SPECIFICATIONS. Refer to the 3.Outer Dimensions UL 508, CSA-C22.2 No. 14 EMC Directive (EN , EN ) Conformity Standards
|
|
|
- Julie Jordan
- 5 years ago
- Views:
Transcription
1 1.General Specifications SPECIFICATIONS Model LR5-01 W Rated Voltage 12V DC Operating Voltage Range Rated Voltage ±10% LED Unit:90mA Typ. Signal Wire Current Buzzer Unit:90mA ( 1) (Per Unit) LED Unit:100mA Max. Buzzer Unit:250mA ( 1) Power Supply Wire 0.7A / Less than 15ms Inrush Current LED Unit:none ( 2) Signal Wire Buzzer Unit:none (Not exceeding Maximum Signal Wire Current Ratings) ( 2) LED Unit : 1W Rated Power Typ. Buzzer Unit : 1.1W ( 1) Consumption LED Unit : 1.1W (Per Unit) Max. Buzzer Unit : 1.2W ( 1) LED Unit : none Standby Power Consumption Buzzer Unit : 0.3W Body Unit : 0.1W Operating Ambient Temperature -20 ~ +50 Operating Ambient Humidity Less than 90% RH (No Condensation) Storage Ambient Temperature Storage Ambient Humidity -30 ~ +60 Less than 90% RH (No Condensation) Mounting Location Indoor Only Mounting Direction Upright Protection Rating IP65(IEC 60529)( 3) / NEMA TYPE 4X,13 EnvironmentalCondition Upright Insulation Resistance Withstand Voltage More than 1MΩ at 500VDC between live part and non-current carrying metallic part 500VAC applied for 1min Between live part and non-current carrying metallic part without breaking insulation Flashing Rate 60±2 Flashes Per Minute Buzzer Sound /Typical Frequency Setting No.1 No.2 No.3 No.4 Rapid intermittent beep / 3378Hz Continuous beep sound / 3378Hz Rapid Hi-Lo / 2016Hz&3012Hz Sweep sound / 1000Hz-4032Hz Depending on DIP Switch Settings Refer to the 6.Buzzer Pattern Set-up Outer Dimensions Refer to the 3.Outer Dimensions UL 508, CSA-C22.2 No. 14 EMC Directive (EN , EN ) Conformity Standards RoHS Directive (EN 50581) FCC Part 15 Subpart B Class A KC (KN , KN ) ( 1)Environmental Condition :Buzzer sound No.2 Continuous beep sound ( 2)When (Gray) power supply wire is not connected, inrush current of 0.7A will flow through the signal wires. Remarks ( 3)LJ Type IP54 Due to the characteristics of the LED elements, a variation in difference of the color tone and brightness of every product may occur UL Recognized Component (File No.E215660) LR-501-W18D-1_9
2 Mass (Tolerance±10%) Sound Pressure Level WJ LJ PJ Environmental Condition (LED Unit) + [Buzzer Unit] 0.2kg + (0.04kg) Tiers + [0.05kg] 0.49kg + (0.04kg) Tiers + [0.05kg] 0.38kg + (0.04kg) Tiers + [0.05kg] Sound Reduction Approx. -10dB Typ.80dB Depending on DIP Switch Settings Refer to the 6.Buzzer Pattern Set-up Buzzer sound No.4 was measured from the total circumfrence of the Buzzer Unit at 1m 2. Model 2.1.1Model Number Configuration Assembly Model Model LR 5 - Tiers Rated Voltage 01 Mounting/Wiring Flashing/Buzzer Body Color W - LED Unit Color Size 5 Φ50 Tiers Body Color 1 1Tier Flashing/Buzzer W Off-white 2 2Tiers B With Flashing/Buzzer 3 3Tiers N No Flashing/Buzzer 4 4Tiers 5 5Tiers Mounting/Wiring WJ Direct Mount/Cable Rated Voltage LJ Pole Mount with L-bracket/Cable 01 12V DC PJ Pole Mount with Circular Bracket/Cable LED Unit Color R Red Y Amber G Green B Blue C White From top to bottom Unit Model(Body Unit) Model LR 5 - Rated Voltage 01 Mounting/Wiring WJ Flashing/Buzzer N Body Color W Size Flashing/Buzzer 5 Φ50 N No Flashing/Buzzer Body Color W Off-white Model Number Example Assembly Model Unit Model (Body Unit) 2.2. UL Registered Model LR5 Rated Voltage 01 12V DC Mounting/Wiring WJ Direct Mount/Cable LR5-301WJNW-RYG Φ50 LED Unit 3T iers 12V DC Direct Mount/Cable No Flashing/Buzzer Off-white (From top to bottom)red Amber Green LR5-501PJBW-RYGBC Φ50 LED Unit 5 T iers 12V DC Pole Mount with Circular Bracket/Cable With Flashing/Buzzer Off-white (From top to bottom)red Amber Green Blue White LR5-01WJNW Φ50 12V DC Direct Mount/Cable No Flashing/Buzzer Off-white LR5-_01WJB, LR5-_01WJN, LR5-_01LJB, LR5-_01LJN, LR5-_01PJB, LR5-_01PJN LR-501-W18D-2_9
3 3.Outer Dimensions 3.1 LR5-01WJ W WJ Direct Mount with Cable LR5-01WJBW LR5-01WJNW (Unit:mm) LR5-101 : LR5-201 : LR5-301 : LR5-401 : LR5-501 : LR5-01 : 99 LR5-101 : 139 LR5-201 : 179 LR5-301 : 219 LR5-401 : 259 LR5-501 : 299 Maximum Board Thickness : 7 Cable : UL2464 (Φ7.5) Signal Wire & Power Supply Wire : AWG24 Cable Length : (1300) Number 1 Name Buzzer Case Material UL Flammability 2 3 Head Cover Globe 4 5 Body Direct Mount Bracket 6 Waterproof Packing Silicone Rubber - 7 Cable PVC VW-1 LR-501-W18D-3_9
4 3.2 LR5-01LJ W LJ L-bracket and Pole with Cable LR5 01LJBW LR5-01LJNW (Unit:mm) LR5-101 : LR5-201 : LR5-301 : LR5-401 : LR5-501 : LR5-01 : 99 LR5-101 : 139 LR5-201 : 179 LR5-301 : 219 LR5-401 : 259 LR5-501 : 299 Number Name Material UL Flammability 1 Buzzer Case 2 Head Cover 3 Globe 4 Body 5 Pole Bracket 6 Pole AL - 7 Rubber Bushing EPR - 8 Cable PVC VW-1 9 L-bracket Steel - 10 Hexagon Nut M22 SUM - Cable : UL2464 (Φ7.5) Signal Wire & Power Supply Wire : AWG24 Cable Length : (1000) LR-501-W18D-4_9
5 3.3 LR5-01PJ W PJ Circular Bracket and Pole Mount with Cable LR5 01PJBW LR5 01PJNW (Unit:mm) LR5-101 : LR5-201 : LR5-301 : LR5-401 : LR5-501 : LR5-01 : 99 LR5-101 : 139 LR5-201 : 179 LR5-301 : 219 LR5-401 : 259 LR5-501 : 299 Number Name Material UL Flammability 1 Buzzer Case 2 Head Cover 3 Globe 4 Body 5 Pole Bracket 6 Pole AL - 7 Circular Bracket 5VA 8 Waterproof Packing Silicone Rubber - 9 Cable PVC VW-1 Cable : UL2464 (Φ7.5) Signal Wire & Power Supply Wire : AWG24 Cable Length : (1000) LR-501-W18D-5_9
6 4.Mounting Dimensional Drawing 4.1 WJ PJ Mounting Dimensional Drawing (Unit: mm) 4.2 LJ Mounting Dimensional Drawing (Unit: mm) LR-501-W18D-6_9
7 5.Wiring Diagram 5.1 Wiring Example LR-501-W18D-7_9
8 5.2 External Contact Capacity IS:Current Capacity VS:Withstand Voltage IL:Leakage Current Recommended contact capacity LED Unit (1 Tier) IS 100mA VS 20V DC ( 1) Buzzer IS 300mA VS 20V DC ( 1) Power Supply IS 700mA VS 20V DC Leakage Current IL 0.1mA LR-501-W18D-8_9
9 6.Buzzer Pattern Set-up T he B Flashing/Buzzer type includes a set up for four different patterns and sound reduction. Set up the preferred pattern, using the DIP Switch after removing the buzzer unit. LR-501-W18D-9_9
LR IP54(IEC 60529) / NEMA TYPE 4X,13 Protection Rating. 60±2 Flashes Per Minute Outer Dimensions
Drawing No. LR-502-W18 Rev. F Page SPECIFICATIONS 1.General Specifications Product Name Signal Tower Model LR - 02 Rated Voltage 24V DC Operating Voltage Range Rated Voltage ±10% LED Unit:40mA Typ. Signal
Type Contact form Enclosure ratings Model Standard SPST-NO (Class A) Flux protection G5LA-1A Sealed
PCB Relay G5LA A Cubic, Single-pole 1A Power Relay Economical cube relay with universal terminal footprint Conforms to VDE435, CQC UL recognized/ CSA certified. High switching power: 1A @ 5VAC Withstands
PRODUCT SPECIFICATION. Stack Lights. Series.
PRODUCT SPECIFICATION Stack Lights Series www.wernerelektrik.com Light Color Significance... Specifications... Functional Specification... Model Number Structure - Stack Lights... Model Number Selection...
Low Signal Relay. To Order: Select the part number and add the desired coil voltage rating, (e.g., G6A-274P-ST-US-DC12).
Low Signal Relay High sensitivity can be driven by digital circuits Low-profile design allows use in 12.70 mm (0.50 in) PC board rack Surge withstand voltage meets FCC Part 68 regulation Units can be mounted
Ordering Information. Text PCB Power Relay G5LE
A Cubic, Single-pole 10-A Power Relay Single-pole 10A 35VDC, 0.8mm contact gap: G5LE-G Single-pole 16A 250VAC: G5LE-E ROHS compliant. Sub-miniature sugar cube relay with universal terminal footprint. Conforms
Load Resistive load (p.f. = 1) Inductive load (p.f. = 0.40, L/R = 7 ms) Rated load 5 A at 250 VAC, 30 VDC 2 A at 250 VAC, 30 VDC
Power PCB Relay G6D-ASI Reduced board space ideal for high-density mounting (45% smaller than the surface area of G6B). Slim package: measures 6.5 W x 17.5 L x 12.5 H mm Switches loads up to 5 A, 250 VAC/30
PCB Relay RC FCC. Ordering Information. Fully Sealed Relay with High Impulse Dielectric for Use in Telecommunications Equipment
PCB Relay Fully Sealed Relay with High Impulse Dielectric for Use in Telecommunications Equipment High sensitivity can be driven by digital circuits. Horizontal design allows use in /2-inch PCB racks.
TDK-Lambda ZWS240BP/A SPECIFICATIONS
SPECIFICATIONS A253-1-1/A-B MODEL ZWS24BP ZWS24BP ZWS24BP ITEMS -24/A -36/A -48/A 1 Nominal Output Voltage V 24 36 48 2 Average Output Current A 1 6.7 5. 3 Peak Output Current (*1) A 2. 13.4 1. 4 Average
For full product information, visit Use the SpeedSpec Code or scan the QR Code for quick access to the specific web page.
Safety Interlock Switches D4S-N D4SN For full product information, visit www.sti.com. Use the SpeedSpec Code or scan the QR Code for quick access to the specific web page. Slim Safety Door Switches with
Ordering Information. Text PCB Power Relay G5RL. Low-profile Relay with Various Models. Power Relays
Low-profile Relay with Various Models Low profile:.7 mm in height Clearance and creepage distance Between coil and contacts: 8 mm/8 mm Between contacts of the same polarity: 3 mm/4 mm Models with AC coil
TDK-Lambda ZWS300BAF/A
ZWS3BAF/A SPECIFICATIONS A254-1-1/A-B MODEL ZWS3BAF ZWS3BAF ZWS3BAF ZWS3BAF ZWS3BAF ITEMS -12/A -15/A -24/A -36/A -48/A 1 Nominal Output Voltage V 12 15 24 36 48 2 Maximum Output Current A 25.. 12.5 8.4
Signaling Lights LD6A. LD6A LED SignaLight Towers Assembled Products. Unique Striped Design Improves Visibility
Unique Striped Design Improves Visibility Key features of the LD6A LED SignaLight Towers include: The striped design with non-illuminated area between the lenses makes the illuminated color very visible.
G7S. Ordering Information. Plug-In Safety Relay. Safety Relay for Machine Control Conforms to EN Standard. H Suitable for safety circuits in press
Plug-In Safety Relay Safety Relay for Machine Control Conforms to EN Standard H Suitable for safety circuits in press machinery, machine tools, and other production machinery Do Not Remove H CE mark (conforms
HL (AZH) LIMIT SWITCHES
COMPACT SIZE LIMIT SWITCHES LIMIT SWITCHES U L PRODUCT TYPE 1. Limit Switches Actuator Type Push plunger Roller plunger Cross roller plunger Panel mount push plunger Panel mount roller plunger Panel mount
PCB Relay. Contact form Terminal Single-side stable Single-winding latching
PCB Relay Subminiature, Sensitive SPDT Signal Switching Relay High sensitivity: 98 mw pickup coil power. Impulse withstand voltage meets FCC Part 68 requirements. Plastic-sealed construction. Unique moving
Single-pole 10A35VDC 0.8mm Contact Gap Power Relay : G5LE-G Single-pole 16A250VAC Power Relay : G5LE-E. Contact Form 10A 35VDC
PCB Relay R G5LE-E/-G Single-pole 0A35VDC 0.8mm Contact Gap Power Relay : Single-pole 6A250VAC Power Relay : G5LE-E Sub-miniature 'sugar cube ' relay with universal terminal footprint. UL class-f coil
G3RV-SL Slim I/O Relay will be discontinued February 2019
NO: RL-163 PRODUCT: G3RV-SL Slim Relay DATE: February 2018 TYPE: Discontinuation Notice G3RV-SL Slim I/O Relay will be discontinued February 2019 Discontinuation Date: February 2019 Note: Date is subject
20 amps 220 amps, 60 Hz VDC VAC G3PA-420B-VD-2 DC amps 440 amps, 60 Hz G3PA-450B-VD-2 DC12-24
Solid State Relays (SSRs) G3PA/G3PB Long Service Life for Circuits that Cycle Frequently D D D D D Built-in heat sink increases life and reliability Voltage turn-on at zero crossing reduces initial inrush
G6K. Surface Mounting Relay with the World s Smallest Mounting Area. Application Examples. Model Number Legend. Ordering Information
with the World s Smallest Mounting Area Subminiature model as small as.2 (H). (W) (L) mm is ideal for high-density mounting ((U)-2F(-Y)). Low profile of.2 mm improves mounting efficiency ((U)-2F(-Y)).
Ordering Information. Text Surface-Mounting Signal Relay G6K
Surface-Mounting Relay with the World s Smallest Mounting Area and a Height of Only 5.2 mm ROHS compliant. Sub-miniature model as small as 5.2 (H) x 6.5 (W) x 10 (L) mm is ideal for high-density mounting.
High-force: 230 g. Projected 7.3 mm General-purpose: 160 g. High-force: 230 g. Flat 4.3 mm General-purpose: 200 g.
Tactile Switch BW Tactile Switch with Sealed Construction for Automatic Soldering Sealed construction conforming to IP67 (IEC-6059) provides high reliability in locations exposed to dust or water. Available
HL (AZH) Limit Switches
COMPACT SIZE LIMIT SWITCHES HL (AZH) Limit Switches Wide selections of actuators, terminals and bodies to meet any application Excellent environmental resistance Die casting caseiec IP67 Plastic caseiec
PRODUCT SPECIFICATION OUTPUT CURRENT (A) OUTPUT CURRENT TOLERANCE ±7% ±7% ±10% ±10% ±7% 1.8. Units % % % Typ. Typ.
0-10V Dimmable FEATURES: AC Input 100~277VAC Built-in Active PFC Function Protection: SCP / OVP / OTP 24V Auxiliary Output 0-10V Dimming Control Dimming 1 ~ 100 Flicker Free High Operating Ambient Temp.:
Industrial Relay KML(1C, 2C)
Industrial Relay KML(1C, 2C) Features 1C: 15A, 2C: 10A switching capability 1.5kV dielectric strength (between coil and contacts) Various terminals available Socket available 1 & 2 poles configurations
Sealed type washable 1C H-1C-C 812H-1C-V 812H-1C-S (SPDT) F 812H-1C-C F 812H-1C-V F 812H-1C-S F
8H Type List 8H Terminal style Contact form Features Miniature PCB Power Relays A 2VAC. High CTI 2 material or product comply with IEC 33-1 are available. UL Insulation Class F. VDE, UL/CUL, TUV, CSA/CUS
Ordering Information. Switching Power Supply S82F. Industrial-Grade Power Supply for General or Peak Load Applications SWITCHING POWER SUPPLIES
Switching Power Supply S82F Industrial-Grade Power Supply for General or Peak Load Applications Correct input voltage range is automatically selected: 1 VAC or 2 VAC. Model S82F-P is suitable for peak
PCB Relay. Contact form Terminals Coil terminals Rated voltage Model SPST-NO #250 tab terminals PCB terminals 5, 12, 24 VDC G4A-1A
PCB Relay Miniature Single-pole Relay with 80-A Surge Current and 20-A Switching Current Ideal for motor switching. Miniature, relay with high switching capacity built-in applications. Creepage distance
PCB Relay. 2. Contact Form 2: DPDT 3. Terminal Shape None: PCB terminal F: Surface mount terminal
PCB Relay Ultracompact, Ultrasensitive DPDT Relay Compact size and low 5-mm profile. Low power consumption (140 mw for single-side stable, 100 to 300 mw for latching type) and high sensitivity. Low thermoelectromotive
Hinged Safety Door Switch
Hinged Safety Door Switch Polymer housing, IP65, and slow-action contacts with positive opening. Two actuator types are available: Shaft Arm lever Arm lever type can be adjusted to allow a right (180 ),
Safety Relay Unit. Ordering Information. Ideal for Safety Door and Emergency Stop Switch Circuits for Machines in European Countries
Safety Relay Unit Ideal for Safety Door and Emergency Stop Switch Circuits for Machines in European Countries Two-pole slim models that are only 22.5 mm wide, three-pole models that are only 68 mm wide,
3. Terminal Shape P : PCB terminals FS: Surface-mounting terminals, short FL : Surface-mounting terminals, long
Surfacemounting Relay Ultracompact and Slim DPDT Relay Suitable for highdensity mounting.(.7 mm (W). mm (L) 9 mm (H)). Dielectric strength of, VAC and an impulse withstand voltage of 2, V for 2 μs (conforms
881WP. Type List. Ordering Information 881 WP1-1A C - - C Basic series designation 4. C -- Contact material AgNi
Type List Terminal style WP (High power type, terminals)-.0mm pitch Contact form A (SPNO) Features Low Profile mm w/ fasten terminals. High Rating 7A 277VAC. High temperature withstand up to 2. UL/CUL
Surface mounting, flush mounting, and DIN track mounting
Solid-state Timer H3JA Economical, Compact, Plug-in Timer Time limit, ON-delay, operation with automatic resetting. DIN size (36 x 36 mm), fits standard 8-pin sockets. Wide choice of supply voltages: 24,
60W Constant Current Mode LED Driver. HBG-60 series. File Name:HBG-60-SPEC
05 SPECIFICATION MODEL OUTPUT INPUT RATED CURRENT RATED POWER CONSTANT CURRENT REGION OPEN CIRCUIT VOLTAGE(max.) CURRENT ADJ. RANGE CURRENT RIPPLE CURRENT TOLERANCE SET UP TIME VOLTAGE RANGE FREQUENCY
RWS50B RWS100B RWS150B RWS300B RWS600B
RWS-B Series 50W to 600W Single Output General Purpose Power Supplies Features 10 Year e-cap Lifetime 7 Year Warranty Global Safety Approvals Compact Size Better Field Reliability Lower Cost of Ownership
Model Number Structure
Power Relay G7J Electromechanical Relays A High-capacity, High-dielectric-strength, Multi-pole Relay Used Like a Contactor Miniature hinge for maximum switching power for motor loads as well as resistive
D4BL. Protective Doors Are Locked Until Machines Completely Stop Operating. Guard Lock Safety-door Switch. Model Number Structure.
Guard Lock Safety-door Switch Protective Doors Are Locked Until Machines Completely Stop Operating A mechanical lock is applied automatically when the Operation Key is inserted. A high level of safety
Type Contact form Model Plug-in socket/solder terminals Hermetically sealed 4PDT MY4H-US
Hermetically Sealed Relay MY4H Hermetically Sealed Relay Ideal for Hazardous Locations Class 1 Division 2 approved. Fully hermetically sealed for hazardous locations. Cadmium-free contacts for environment-friendly
Model Number Structure
Solid State Relays (Single-phase) G3PB New Single-phase Solid State Relays with Compact Size for Heater Control Slim models with a thickness of only 22.5 mm are also available. Compact design achieved
Cable length. 3: 3 m. 4: Adjustable mounting (vertical) 4: 3NC (slow action) 5: 5 m. (Slow-action) Horizontal 1 m D4GS-N1R D4GS-N2R D4GS-N3R D4GS-N4R
Slim Safety-Door Switch Industry s Smallest Safety-Door Switch (with 3 Contacts) for Use in Space-Confined Areas Slim body design (85 x 30 x 17 mm) suitable for small door applications 2-contact and 3-contact
Max. Input Power (W) Inrush Current (A pk /µs)
Output Power (W) Output Voltage (V) Output Current (A) Tcase Max 150 60~210 0.70 80 C Wiring Diagram Input Current 1.4A@120VAC 0.6A@277VAC 0.67A@250VDC Max. Input Power (W) Inrush Current (A pk /µs) Max.
UCS-CHR24V55W. Combined Power Supply & Battery Charger. Data Sheet
Combined Power Supply & Battery Charger Data Sheet INTRODUCTION UCS-CHR24V55W is a combined charger and power supply with dedicated outputs for both charging and power supply. With a large input range
D4BS. Safety-door Switch. Model Number Structure. Switch D4BS - S Operation Key D4BS - K. Ordering Information
Safety-door Switch Safety-door Switch s Special Operation Key Directly Pulls Apart the Contacts from Each Other and Contributes to the Safety of the Production Site Conforms to EN (TÜV) standards corresponding
UNA SERIES Embedded Power Supply Features Model naming method UNA 350P / Applications UNA Conformity to RoHS Directive Product Line-up
SERIES 350PB, PN 350PB/350PN Specifications CH 2 3 5 Voltage Range (*)(*8) V AC85-265 (AC85-5 : Need output derating) Frequency (*)(*8) Hz 7-63 Power Factor (00/20VAC)(typ) (*5) 0.98 / 0.92 (Ta=25) Input
PRODUCTS: POWER SUPPLY
PRODUCTS: POWER SUPPLY Impact Lighting Inc. All rights reserved. Impact Lighting Inc. Reserves the right to change specifications without notice. 138 POWER SUPPLY 15W AC-DC [12V/1.25A] UNIVERSAL POWER
INDUSTRIAL POWER SUPPLIES SFL-SERIES
INDUSTRIAL POWER SUPPLIES SFL-SERIES Operating Instructions 1. Application The SFL-series are compact, rugged switching power supplies designed for applications in process automation and other industrial
PCB Relay. Ordering Information. SPST-NO Type Breaks 10-A Loads; SPST-NO + SPST-NC Type Breaks 8-A Load G6C - - VDC
PCB Relay SPST-NO Type Breaks 10-A Loads; SPST-NO + SPST-NC Type Breaks 8-A Load Compact: 20 15 10 mm (L W H). Low power consumption: 200 mw. Flux protection or fully sealed construction available. Unique
Model Pressure range ON/OFF output Linear output
Digital Sensor Sensor with Easy-to-Read LED Display status can be checked at a glance from the red digital pressure value and analog bar displays. Measurement pressure is averaged by the chattering prevention
Model Number Structure
Terminal Relay G6B-4@@ND Compact Terminal Relay with 4 Independent Outputs Equipped with four G6B Mini-relays that are compact, highly sensitive, and highly resistant to dielectric surges, and that can
56 mm sq. (2.20 inch sq.)
56 mm sq. (2.2 inch sq.) 1.8 /step RoHS Bipolar winding, Lead wire type Unipolar winding, Lead wire type p. 68 Customizing Hollow Shaft modification Decelerator Encoder Varies depending on the model number
G7L. A High-capacity, High-dielectric-strength Relay Compatible with Momentary Voltage Drops. Application Examples. Model Number Legend
A High-capacity, High-dielectric-strength Relay Compatible with Momentary Voltage Drops No contact chattering for momentary drops up to % of rated. Wide-range AC-activated coil that handles 1 to 1 or to
Safety Limit Switch
Safety Limit Switch D4B-@N CSM_D4B-_N_DS_E_5_1 Snap-action contact with certified direct operation certification. Maintenance, seal, and resistance to shock increased and direct mechanism added. Three-conduit
PCB Relay. Ordering Information. Compact, Low-cost 30-A Power Relay for PC Board or Panel-mounted Applications G8P - - VDC
PCB Relay Compact, Low-cost 30-A Power Relay for PC Board or Panel-mounted Applications Compact, yet capable of switching up to 30-A loads. Complies with UL873 and UL508 column A spacings (1/8 through
PS5R-S. Switching Power Supplies
TREICHL-ATM Electronic Auf der Bült 1-12 D 41189 Mönchengladbach Tel. 2166 8545 Fax 2166 8547 email: atm@treichl.de internet: www.atm-treichl.de PS5R-S Switching Power Supplies Class Create More Space
PCB Relay. Ordering Information. Surface Mounting DPDT Relay G6S
PCB Relay Surface Mounting DPDT Relay Long terminals for ideal for soldering and mounting reliability. Space-saving inside-l terminal. High dielectric strength between coil and contacts (2,000 VAC), and
Safety Interlock Switches
Safety Interlock Switches ATK ATK Safety Key Selector Switch Key-type selector switch with direct opening mechanism Selector Switch for secure equipment activation during maintenance 0 types of exclusive
VA, VF, and VS Series Direct Mounted Globe Valve Assemblies. Application. Features
TAC 1354 Clifford Avenue P.O. Box 2940 Loves Park, Illinois 61132-2940 www.invensysibs.com Two-Way and Three-Way Globe Valve Assemblies with 220 lbf Linear (979 N) Spring Return DuraDrive Actuators Submittal
A22NK. Key-type Selector Switches
Key-type Selector Switches -mm dia. Key-type Selector Switches Control panel miniaturization through a more compact design and modified wiring direction. Addition of Push-In Plus terminal blocks for easy
ZWD100PAF. Conformity to RoHS Directive
-SERIES Dual Output W - 225W Features 15 Complies the standard of the harmonics current limiter Worldwide input: 85-265VAC Peak load accommodatable double power: Approximately twice the value of average
Indoor Linear 50W Driver SI-CU WW
Product Data Sheet Rev.2.0 2016. 5. 27 1# LED Driver Indoor Linear 50W Driver SI-CU1425001WW Constant Current LED Driver Features & Benefits Output Current Range: 500~1400 ma (adjustable via R-set) Output
LPF-25 series. 25W Constant Voltage + Constant Current LED Driver
F 110 M M SELV IP67 Features Constant Voltage + Constant Current mode output Plastic housing with Class II design Built-in active PFC function Class 2 power unit Fully encapsulated with IP67 level Typical
Power consuption motor (motion) Power consuption standby (end position) Auxiliary switch Contact load Switching point
Actuators Technical data sheet Continuous control of spring return actuator Description Spring-return actuator for adjusting and regulating dampers and valves in air conditioning and ventilation. Torque
D4B- N. Safety Interlock Switches. Safety Limit Switch. Specifications. Standards and EC Directives. Certified Standard Ratings D4BN
Safety Interlock Switches D4B- N D4BN Safety Limit Switch Snap-action contact with certified direct operation. mechanism (NC contacts only) added to enable contacts when faults occur, such as fused contacts.
D4DL. Guard Lock Safety-door Switch. Ordering Information. Model Number Legend Switches D4DL- -
Guard Lock Safety-door Switch Polymer housing, IP65, and slow-action contacts with positive opening. 2 versions Mechanical lock/solenoid release Solenoid lock/mechanical release Rotatable operating head
LED Lights Singal Tower
LED Lights Singal Tower 145 CLA CLA LED Light Bar CLA-2S-CD Daylight, Amber Natural White IP66/67/69K Luminous Color CLA-3S-CD CLA-6S-CN More than a diffusion LED light bar, it can be used in places like
PCB Relay. Single-side stable EN60950/EN41003 PCB terminal G6S-2 G6SU-2 G6SK-2 G6S-2-Y Surface mounting. stable
PCB Relay Surface Mounting DPDT Relay Long terminals for ideal for soldering and mounting reliability. Space-saving inside-l terminal. High dielectric strength between coil and contacts (2,000 VAC), and
B3F. Miniature, Space-saving Switch
B3F Miniature, Space-saving Switch Long mechanical / electrical service life Ideal for applications such as audio, office and communications equipment, TVs, etc Taped radial, vertical, high-force, and
LD6A. LED SignaLight Towers. Clear, audible alarm sound. Warning/caution indicated by flashing light. Complies with IEC Standards (IEC60073)
LD6A LED SignaLight Towers Steady/Flashing/Alarm Warning/caution indicated by flashing light Complies with IEC Standards (IEC073) Clear, audible alarm sound 3.3 khz 70 to 90 db 2 3 4 5 LD6A LED SignaLight
Illuminated buzzer for elevators, robots and production sites
ø22mm HW1Z Illuminated Buzzer Illuminated buzzer for elevators, robots and production sites Combination buzzer and pilot light Alerts workers of danger with sound and light Waterproof construction HW1Z
HL (AZH) Limit Switches
COMPACT SIZE LIMIT SWITCHES HL (AZH) Limit Switches Compact, high-performance limit switch with superior environmental resistance. Broad lineup covers from die casting cases to economical plastic cases.
Ordering Information. Snap Action Switch D2F. Subminiature Snap Action Switch D2F- Model Number Legend. Snap Action Switch D2F 31
Snap Action Switch Subminiature Snap Action Switch Switches 3 A loads (general-purpose), 1 A loads (low force general-purpose) and 0.1 A loads(microvoltage/ microcurrent) Long life span assured by high-precision
G9SA-TH. Two-Hand Controller. Ordering Information. Specifications. 45-mm Wide Two-hand Control Circuit. H Two-hand Controller, easy-to-connect
Two-Hand Controller -mm Wide Two-hand Control Circuit H Two-hand Controller, easy-to-connect Expansion Units available H Positive, force-guided contacts H DIN-rail mounting and panel mounting available
Features. Emergency Stop Switch A22E. Install in 22-dia. or 25-dia. Panel Cutout. Safety Lock Mechanism to Prevent Misuse.
Switch A22E Install in 22-dia. or 25-dia. Panel Cutout Direct opening mechanism to open the circuit when the contact welds. Safety lock mechanism prevents operating errors. Easy mounting and removal of
For full product information, visit Use the SpeedSpec Code or scan the QR Code for quick access to the specific web page.
Force-Guided s & Power Contactors For full product information, visit www.sti.com. Use the SpeedSpec Code or scan the QR Code for quick access to the specific web page. Multi-pole Power for Contactor Current
D4DL. Guard Lock Safety-door Switch. Model Number Structure
Guard Lock Safety-door Switch Two new types added to series: Mechanical-lock models that lock automatically when the Operation Key is inserted, and solenoid-lock models that lock when voltage is applied
(with Class-1 AC resistive load) 3. G3PB-215B-2N-VD kW max. (25 A) G3PB-225B-3N-VD 2. G3PB-225B-2N-VD kw max. (35 A) G3PB-235B-3N-VD 2
Solid-state Contactor (New Heat Sink Construction) G3PB Space and working time saved with new heat sink construction. Series now includes 480-VAC models to allow use in a greater range of applications.
Supply voltage 12 to 24 VDC (10 to 30 VDC), ripple (p-p) 10% max. 100 to 220 VAC (90 to 250 VAC), 50/60 Hz
R Pancake Style Inductive Prox Long-Range Proximity Sensor Detects Metal Objects at 50 mm H Ideal for many industrial automation applications H Choose DC 3 -wire or AC 2 -wire models H Rugged die -cast
A165-E. Ordering Information. Emergency Stop Switch. For Panel Cutout of 16 mm
Emergency Stop Switch For Panel Cutout of 16 mm H Modular construction, easy installation H Positive opening mechanism with a minimum contact separation of 3 mm in accordance with EN6947-5-1, for NC contacts
Product discontinuation. Notices. Discontinuation Notice of Safety Relay and Socket. G7S series, P7S series. Wire connection
PRODUCT NEWS Product Discontinuation Notices February 1, 2012 Safety Relays No. 2012037E Discontinuation Notice of Safety Relay and Socket., P7S series Product Discontinuation Safety Relay Socket P7S series
1 Form A 5A small size power relay for interface
1 Form A 5A small size power relay for interface PQ RELAYS RoHS compliant Protective construction: Sealed type FEATURES 1. Compact and slim 20 mm (L) mm (W) 16 mm (H).787 inch (L).394 inch (W).630 inch
Power Contactor with Mirror Contacts
LLAME SN COSTO Force-Guided Relays Power Contactor with Mirror Contacts Contents Selection Guide 2 Force-Guided Relays G7SA G7S- -E 3 8 Power Contactor with Mirror Contacts J7KNA-AR G7Z 11 15 1 LLAME SN
General Purpose Relay
General Purpose Relay Exceptionally reliable general purpose relay Long life (minimum 100,000 electrical operations) assured by silver contacts Built-in operation indicator (mechanical, LED), diode surge
SELV IP30 (CCC optional)
Features Constant Voltage + Constant Current mode output Plastic housing with Class II design Built-in active PFC function Class 2 power unit Fully encapsulated with IP30 level, optional IP67 rating Typical
2-Color Display High-Precision Digital Pressure Switch
2-Color Display High-Precision Digital Pressure Switch Series ZSE3/ISE3 2-color digital display allows you to choose the setting according to your application requirements. 4 different display settings
D4DS. Compact Interlock Safety Door Switch. Compact Safety Switch Saves Space and is Ideal for a Variety of Doors. Refer to Precautions on page 9.
Compact Interlock Safety Door Switch Compact Safety Switch Saves Space and is Ideal for a Variety of Doors Positive opening mechanism and double insulation approved by TÜV and BIA. Five-direction Operation
Square D General Purpose Relays
Square D General Purpose Relays Class 0R plug-in relays 0RS (SPDT) 0RS (DPDT) 0RS3 (3PDT) 0RS (PDT) Catalog 0 Contents Class 0R plug-in relays bbspecifications....................................................
Emergency Stop Switch A165E. Ordering Information. Mounting Aperture of 16 mm
Emergency Stop Switch Mounting Aperture of 16 mm Modular construction, easy installation Positive opening mechanism with minimum contact separation of 3 mm in accordance with EN60947-5-1, Conforms to EN418
NO NO NO. Standard Interlock Safety Switches HS6B. HS5E-K Key Locking Safety Interlock Switches
Standard Interlock Safety Switches HS6B HS5E-K Key Locking Safety Key features: Head removal detection circuitry. High-security pin tumbler key types are used. Sixteen types of key numbers are available,
General Purpose Relay
General Purpose Relay KML 15A switching capability 1.5kV dielectric strength (between coil and contacts) Various terminals available Socket available 1 to 3 pole configurations 1. COIL DATA (at 23 ) 1)
General Purpose Relay
General Purpose Relay Designed small, 2- and 3-pole types break 5 A loads and 4-pole type, 3 A load High reliability, long life Ultra-high sensitivity with quick response High vibration/shock resistance
Application Support. Product Information. Omron STI. Support Engineers are available at our USA headquarters from
Omron STI Application Support Thank you for your interest in Omron STI products. Please contact Omron STI with your application questions. Support Engineers are available at our USA headquarters from 4:00
Mounting type Contact form PCB terminals Screw terminals Quick-connect terminals
Power Relay A High-capacity, High-dielectric-strength, Multi-pole Relay Used Like a Contactor Miniature hinge for maximum switching power for motor loads as well as resistive and inductive loads. No contact
10 AMP POWER RELAY. Breakdown voltage* 2. Operate time* 3 (at nominal voltage) Shock resistance. Vibration resistance. Unit weight
VDE 2c, 3c AMP POWER RELAY RELAYS 2. 1.72 FEATURES Interchangeable with existing models Long life and high reliability High contact capacity up to A 20 Available with plug-in/solder and quick-connect terminals
Max. Output Power. Efficiency (1) 110Vac 220Vac. 450 ma 90 ~ 305 Vac 445 Vdc 200 W 92% EUC-200S045ST
LED Driver EUC200SxxxST 20110114 D Features Ultra High Efficiency (Up to ) Active Power Factor Correction (0.99 Typical) Constant Current Output Lightning Protection AllRound Protection: SCP, OTP, OVP
Series 1. Series 1 Pressure Switch. Pressure Switches Inc. Quality Pressure Solutions. Pressure Switches 1 G 10 N Key Features.
Model 1A 1C 1G 1Z 1P 1H Inc. Series 1 Series 1 Pressure Switch High, Low, Differential & Vacuum Pressure Switch options available All Anodized Aluminum Construction Multiple s Available UL & cul Approved
720 W / 24 V On-board Battery Charger. for industrial applications. Product Data Sheet
for industrial applications Product Data Sheet 720 W / 24 V On-board Battery Charger for industrial applications Features IP65 protection degree Battery selection via GUI, supporting all leading battery
FE100/FE200. Inverter
RoHS-Compliant FE1/FE2 A new inverter that enables speed control to be set easily with a built-in digital display. The inverter parameters have been set exclusively for Oriental Motor's three-phase motors,
SAV Electronic Valve Actuator
Document No. 155-548 Non-spring Return, 24 Vac/dc, 3-Position Control Description The SAV Non-spring Return (NSR), Electronic Valve Actuator requires a 24 Vac/dc supply to provide three-position (floating)
IS 15885(Part 2/Sec13) R ( for 24V only)
THOMAS SAMUEL THOMAS SAMUEL Bauar t gepruft Sicherheit egel ma ge od o s be wac g W Constant Voltage + Constant Current LED Driver 110 M IP67 Features Constant Voltage + Constant Current mode output Plastic
Subminiature Basic Switch
Subminiature Basic Switch Subminiature Basic Switch Offers Long Life and High Reliability A design that combines simplicity and stability by the use of two split springs ensures a long durability of 30,000,000