INSTALLATION& OWNER S MANUAL

Transcription

1 INSTALLATION& OWNER S MANUAL WIRE CONTROLLER OF AIR CONDITIONER MODEL: KJR-120C/TF-E(12V) KJR-120C/TF-G(12V) KJR-120C/TF-I(5V) KJR-120C/TF-H(12V) KJR-120C/TF-J(5V) Thank you very much for purchasing our product. Before using your unit, please read this manual carefully and keep it for future reference.

2 This manual gives detailed description of the precautions that should be brought to your attention during operation. In order to ensure correct service of the wired controller please read this manual carefully before using the unit. For convenience of future reference, keep this manual after reading it.

3 CONTENTS 1. SAFETY PRECAUTIONS INSTALLATION ACCESSORY INSTALLATION METHOD SPECIFICATION FEATURE AND FUNCTION OF THE WIRED CONTROLLER NAME ON THE LCD OF THE WIRE CONTROLLER NAME OF BUTTON ON THE WIRE CONTROLLER PREPARATORY OPERATION OPERATION TIMER FUNCTIONS WEEKLY TIMER FAULT ALARM HANDING TECHNICAL INDICATION AND REQUIREMENT...31

4 1. g g WARNING 1 NOTE

5 2. INSTALLATION ACCESSORY Select the installation location Preparation before installation No. Name Qty. Remarks Wire controller Wall plugs Plastic screw bars M4X20 (For Mounting on the Wall) For Mounting on the Wall M4X25 (For Mounting on switch box) For fixing on switch box 7 1 Optional 2 Prepare the following assemblies on the site. No. Name Qty.(embeded Specification into wall) (only for reference) Remarks 1 Switch box 1 2 Wiring Tube(Insulating Sleeve and Tightening Screw) 1

6 2. INSTALLATION ACCESSORY 3

7 3. INSTALLATION METHOD Wiring Principle Sketch: red black yellow brown Wire controller 4-Core Shield Cable, the length is decided by installation Insert of the mainboard CN40 red black yellow brown Indoor unit mainboard 4

8 3. INSTALLATION METHOD 3.Wiring figure 4-core shielding wire 4.Remove the upper part of wire controller Slots 5

9 3. INSTALLATION METHOD 4. Fasten the back plate of the wire controller Switch box Back plate 6

10 3. INSTALLATION METHOD 7

11 3. INSTALLATION METHOD 6. Wiring Top side wire outlet A. For exposed mounting, four outletting positions. There are three need cutting. Left side wire outlet Right side wire outlet Bottom side wire outlet Cutting place of top side wire outlet Cutting place of left side wire outlet Cutting place of right side wire outlet B.Shielded wiring Embedded switch box wiring Wiring through the wall Putty Trap Putty Putty Trap Trap Wiring hole Wall hole and wiring hole Diameter of wall hole:φ20mm CAUTION Avoid the water enter into the wired remote controller, use trap and putty to seal the connectors of wires during wiring installation. (Fig.3-10) When under installation, reserve certain length of the connecting wire for convenient to take down the wired remote controller while during maintenance. 8

12 3. INSTALLATION METHOD 7.Reattach the upper part of the wire controller After adjusting the upper case and then buckle the upper case; avoid clamping the wiring during installation. ( 1) 9

13 4. SPECIFICATION 10

14 5. FEATURE AND FUNCTION OF THE WIRED CONTROLLER Lifting panel 11

15 6. 12

16 7. 13

17 7. 14

18 8. Set the current day and time 15

19 Remote signal receiving function The wired remote controller can be a remote signal receiving device, you can use the wireless remote controller to control the air-conditioner through the wired remote controller when the system have been powered on. To start/stop operation 6 To set the operation mode 16

20 Room temperature sensor selection 17

21 PTC function (on some models) Child lock function C & F scale selection (on some models) 18

22 Faceplate function (on some models), Left-right airflow swing (on some models) 19

23 Up-Down airflow direction and swing (on some models) and - 20

24 21

25 To set the On or Off TIMER

26 To set the On and Off TIMER

27 1 Weekly timer setting 2 Day of the week setting 3 Time scale setting 24

28 4 Time setting 5 Operation mode setting 6 25

29

30 WEEKLY timer operation To set the DAY OFF (for a holiday) 1 During the weekly timer, press the Confirm button to set the day. 2 Press the button + and - to select the day to set the DAY OFF. 27

31 3 4 5 : Copy out the setting in one day into the other day

32

33 Delete the time scale in one day

34 31

35