SRAMCQ09. Designed for Dodge Ram vehicles Stillwater Designs SRAMCQ Subwoofer. Subwoofer Harness.
|
|
- Constance Pope
- 5 years ago
- Views:
Transcription
1 SRAMCQ09 Designed for Dodge Ram vehicles Subwoofer Alternate Amp Bracket Subwoofer Harness Subwoofer Amplifier Wire Ties x 6 Adapter Harness Subwoofer Power Harness Bolt (only for solid rear bench seat) Fuse Wire Taps 2018 Stillwater Designs SRAMCQ
2 Power Harness Routing 1. Disconnect negative battery cable 2. Make sure the supplied fuse is not installed in the fuse holder of the subwoofer power harness and connect the harness to the stud pictured in Fig. 1. Torque stud nut to 14Nm (124in-lbs) 3. Route the power harness toward the driver s side factory firewall grommet and secure with the supplied wire ties. 4. Make a small incision in the grommet and pass the power harness into the cabin. Fig. 2 Fig 1 Fig 2 5. Install the black two pin power connector on the subwoofer power harness by first inserting the terminal fully into the connector and then depressing the blue retainer. Fig. 3 Note: Make sure the blue retainer in the center of the connector is not depressed it should be flush with the front of the connector. If the retainer is depressed, the terminal will not fully seat in the connector body. Make sure the terminal is installed into position 1 on the connector body. There should be a block-out plug installed in position 2 in order to prevent the terminal from being installed into the wrong position on the connector. Insert terminal first Then depress blue retainer Fig 3 6. ground wire for both the subwoofer and amplifier harness. Fig. 11 Torque to 5Nm 2
3 Subwoofer Harness Routing 7. Remove the driver s side kick panel as well as the front and rear sill plate along the bottom of the door opening by snapping loose. 8. Connect the subwoofer harness ground ring to the factory ground point below the steering column. Fig Connect the subwoofer two-pin black power connector to the power harness two-pin connector. Fig 4 Subwoofer Input Connection with Non-Premium Audio (base audio) 10. Find the gray/yellow striped wire and the gray/purple striped wire in the connector to the left of the brake pedal. For see Fig. 5, For 2013-present, see Fig. 6 Fig 5 Fig Install one of the supplied wire taps on the gray/yellow wire and the gray/purple wire using a pair of pliers. 12. Connect the two-pin adapter harness to the subwoofer harness and then connect the brown wire of the adapter harness to the gray/purple wire and the green wire of the adapter harness to the gray/yellow wire. Subwoofer Input Connection with Kicker Amplifier 13. Connect the white two-pin input connector of the subwoofer harness to the white two-pin connector of the Kicker amplifier harness. Subwoofer Input Connection with Premium Audio (includes Kicker 12 channel upgrade on ) 14. Locate the factory amplifier just below and left of the steering column. Find the gray/brown striped wire and the green/brown striped wire in the 16-pin amplifier connector and install the supplied wire taps with pliers. 15. Connect the brown wire of the adapter harness to the gray/brown wire. Connect the green wire of the adapter harness to the green/brown wire. 16. Connect the adapter harness two-pin connector to the subwoofer input two-pin connector. 3
4 17. Route the subwoofer harness along the driver s side door opening. Route the ten-pin connector under the driver s seat and out of the existing hole. Fig. 7 Fig 7 Subwoofer Amplifier Mounting without Air Bag Control Module Note: The Air Bag Control Module is located under the driver s seat on certain model trucks. The amplifier/bracket assembly as shipped will not install if the Air Bag Control Module is present. If the truck is equipped with the Air Bag Control Module, skip to steps Remove the two 8mm bolts holding the bracket for the seat wiring. Mount the amplifier/ bracket assembly as shown in Fig.8 and replace the two 8mm bolts. Fig 8 Subwoofer Amplifier Mounting with Air Bag Control Module 19. Remove the subwoofer amplifier from its current bracket by removing the four screws and pulling the connector loose. Fig Reattach the subwoofer bracket to the alternate bracket using the original screws. Fig. 10 Fig 9 Fig 10 4
5 21. Remove the two M6 nuts securing the air ride control module. Fig Install the amplifier bracket over the studs and reinstall the M6 nuts. Torque to 5Nm. Fig.12 Fig 11 Fig Connect the ten-pin connector of the harness to the amplifier. Slide the red locking tab over to prevent the connectors from accidentally becoming disconnected. 24. Route the subwoofer four-pin connector toward the rear seat. 25. If the vehicle is equipped with a fold-out cargo tray under the rear seat, the driver s side portion will need to be removed to allow the subwoofer to install Cargo Tray Removal 26. Remove the four 18mm bolts securing the driver s side rear seat and remove the seat from the truck. Fig Remove the plastic cover on the side of the seat. (not necessary on some models) Fig. 14 Fig 13 Fig Remove the 13mm and 10mm bolt on both sides of the bottom of the rear seat and remove the cargo tray. Fig Remove the front latch. (this will not be reinstalled) (not present on one-piece bench seat) 30. Reinstall seat and loosely install the two rear bolts. Fig. 16 Fig 15 Fig 16 5
6 2013-present Cargo Tray Removal. 31. Remove the two smaller nuts in the rear. Fig Fold the tray up and remove the two seat bolts and then remove the tray. Fig. 18 Fig For vehicles equipped with one piece rear bench seats remove the 18mm bolt securing the driver s (left) side of the seat to the floor. 34. For one piece rear bench seat you will also need to find threaded nut insert in the floor pan concealed by the carpet flap. Fig Set the enclosure in place and reinstall and tighten all seat bolts and Torque to 30 ft/lbs (a bolt is supplied for one-piece bench seats) Fig. 20 Fig 18 Fig 19 Fig Route the subwoofer harness behind the plastic trim panel on the end of the rear seat and under the driver s side rear outermost seat bracket. Fig Connect the four-pin plug of the subwoofer harness to the subwoofer enclosure. 38. If the vehicle is equipped with a factory subwoofer it must be disconnected for the system to operate properly. 39. Reinstall all previously removed parts in reverse order. 40. Install the supplied fuse in the fuse holder under the hood. 41. Reconnect the negative battery cable. Torque to 5Nm. Fig 21 6
7 Troubleshooting the Kicker Integrated Systems If you experience a problem once the subwoofer or amplifier are installed use this guide to locate the trouble. The radio is working, but the Subwoofer is not working: Check the battery voltage to make sure it is not discharged below 11 volts. Check the negative battery cable to see if it has been securely tightened back on the battery. Check the inline fuse located near the battery to make sure it is plugged in completely, and not blown. Check the inline +12 volt power connector near the firewall to make sure it is plugged in securely. Check the inline connectors near the subwoofer enclosure to make sure they are plugged securely. Check the ground wire connection to make sure it is tightly secured to the proper ground in the vehicle. Check the audio input signal connection to make sure it is secure and connected to the proper wiring. Test with different music in case there is no low frequency audio in the initial sound check. Symptom Possible Cause Solution No Subwoofer Output Radio Not Coming On Fuse not installed in inline fuse holder on subwoofer and / or amp harness Low battery voltage Negative battery cable not connected Power wire connector not connected to body harness Install fuse into fuse holder. Refer to instructions for correct placement Recharge the battery Reconnect negative battery cable Connect power wire to body harness. Check for loose connection Ground wire not grounded properly Check ground wire with voltmeter to insure it is a good Balance or fader controls not set to neutral position No low frequency information in music Subwoofer harness not properly / Completely connected to subwoofer. Blown radio fuse Low battery voltage Set balance and fader control to center settings. (only effects stand-alone subwoofer kit) Test with several different songs Securely fasten both of the connectors on the subwoofer harness to the subwoofer. Check for loose connections. Refer to owner's manual for radio fuse location and value Recharge the battery 7
8 If you continue to experience problems after troubleshooting, please contact KICKER Technical Support at (800) ext. 6009, or P.O. Box 459 Stillwater, Oklahoma USA (405)
PRAMCQ13. Designed for Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles
PRAMCQ13 Designed for 2013 2017 Dodge Ram vehicles with base audio Not Compatible with 2018 and newer Dodge Ram vehicles Subwoofer Alternate Amplifier Bracket Amplifier Subwoofer Harness Subwoofer Amplifier
More informationSFSDC08. Designed for 2008-present Ford F250/F350 Super Crew vehicles. Adaptor Harness. Subwoofer Power Harness
SFSDC08 Designed for 2008-present Ford F250/F350 Super Crew vehicles Subwoofer Enclosure Subwoofer Harness Adaptor Harness Wire Ties Wire Taps Fuse Factory Amplifier Relocation Bracket, Nut and Bolt Subwoofer
More informationSWRA211. T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY 200 WATT AMP BRACKET ASSEMBLY POWER HARNESS OVERLAY HARNESS.
SWRA211 Designed for 2011-2014 Jeep Wrangler two door with base audio or premium audio T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY 200 WATT AMP BRACKET ASSEMBLY POWER HARNESS 2012 Stillwater
More informationPFSDC12. Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Stillwater Designs PFSDC12-A Subwoofer Enclosure
PFSDC12 Designed for 2012 and newer Ford F250/F350 Super Crew vehicles Subwoofer Enclosure Amplifier/Bracket Assembly Subwoofer Power Harness Amplifier Harness Subwoofer Harness Amplifier Power Harness
More informationDesigned for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System. M6 Bolt X 2
SF150SC15 Designed for 2015 Ford F150 Super-Cab and Super-Crew vehicles (Compatible in vehicles with or without Sony System Subwoofer Assembly Amplifier Relocation Bracket (not used on non Sony trucks)
More informationPSIEXT16I. Designed for 2016 and newer 1500 Series and Heavy Duty GM Silverado/Sierra Double Cab vehicles with 7 inch touchscreen radio
PSIEXT16I Designed for 2016 and newer 1500 Series and Heavy Duty GM Silverado/Sierra Double Cab vehicles with 7 inch touchscreen radio Not compatible with Bose Audio Not compatible with 4.2 inch radio
More informationPF150SC15. Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Stillwater Designs PF150SC15-A
PF150SC15 Designed for 2015 and newer Ford F150 Super-Cab and Super-Crew vehicles without Sony System Subwoofer Assembly Amplifier Assembly Amplifier Harness 2015 Stillwater Designs PF150SC15-A2-20160502
More informationSCAMA10. Designed for Chevrolet Camaro vehicles. Subwoofer Assembly. Subwoofer Bracket Wire Ties x6 Wire Taps x2 Rubber Bumper
SCAMA10 Designed for 2010-2015 Chevrolet Camaro vehicles Subwoofer Assembly Subwoofer Harness Subwoofer Bracket Wire Ties x6 Wire Taps x2 Rubber Bumper 2012 Stillwater Designs SCAMA10-A3-20151028 M6 Nut
More informationSF150C09. Designed for Ford F150 Super-Crew vehicles (not compatible with trucks that have Sony Factory Premium Audio) Subwoofer Assembly
SF150C09 Designed for 2009-2014 Ford F150 Super-Crew vehicles (not compatible with trucks that have Sony Factory Premium Audio) Subwoofer Assembly Subwoofer Power Harness Subwoofer Body Harness M6 Bolts
More informationPSIEXT14. Subwoofer Assembly. Subwoofer Power Harness. Subwoofer Body Harness. 25A Fuse Wire Ties x 6 Washers x 2
PSIEXT14 Designed for 2014 and newer Chevrolet Silverado & GMC Sierra Double-Cab 1500 series with base radio 2015 and newer Chevrolet Silverado & GMC Sierra Double-Cab 2500/3500 with base radio (Not compatible
More informationDesigned for 2005 & newer Ford Mustang (Not compatible with Convertible)
Designed for 2005 & newer Ford Mustang (Not compatible with Convertible) SMUS05 Subwoofer Enclosure Assembly Power Harness Body Harness Input Adapter Wire Ties x6 M6 Nut 25A Fuse Wire Taps x2 SMUS05 A.2
More informationPSICRE14. Subwoofer Assembly. Subwoofer Power Harness. Subwoofer Body Harness 25A Fuse Wire Ties x Stillwater Designs PSICRE14-A
PSICRE14 Designed for 2014 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 1500 series with base radio 2015 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 2500/3500 with base radio (Not compatible
More informationSSUTAYU15. Designed for 2015 and newer Chevrolet Tahoe/Suburban and GMC Yukon/Yukon XL vehicles
SSUTAYU15 Designed for 2015 and newer Chevrolet Tahoe/Suburban and GMC Yukon/Yukon XL vehicles Subwoofer Assembly Subwoofer Harness Subwoofer Power Harness 2018 Stillwater Designs SSUTAYU15-20180313 Wire
More informationSSICRE14. Subwoofer Assembly. Subwoofer Body Harness. Subwoofer Power Harness. Fuse Wire Ties x 6 Wire Taps x 2 Adaptor Harness
SSICRE14 Designed for: 2014 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 1500 series with base or premium radio 2015 and newer Chevrolet Silverado & GMC Sierra Crew-Cab 2500/3500 with base or premium
More informationPWRA215. Designed for 2015 and newer Jeep Wrangler two door with base audio. T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY
PWRA215 Designed for 2015 and newer Jeep Wrangler two door with base audio T-TAP x2 10MM BOLT FUSE WIRE TIES x6 SUBWOOFER ASSEMBLY 200 WATT AMP BRACKET ASSEMBLY POWER HARNESS 2015 Stillwater Designs PWRA215
More informationSCHAL08. Designed for Dodge Challenger vehicles. Subwoofer Assembly. 200W Amplifi er. Wire Harness
SCHAL08 Designed for 2008-2014 Dodge Challenger vehicles Subwoofer Assembly 200W Amplifi er Wire Harness 2012 Stillwater Designs SCHAL08-A3-20140930 Wire Ties x6 25A Fuse #8 Sheet Metal Screws x4 Body
More informationPCAMA13MY. Designed for Chevrolet Camaro vehicles with MyLink. Subwoofer Assembly. Subwoofer Bracket Wire Ties x6 Rubber Bumper
PCAMA13MY Designed for 2013-2015 Chevrolet Camaro vehicles with MyLink Subwoofer Assembly Subwoofer Harness Adapter Harness Subwoofer Bracket Wire Ties x6 Rubber Bumper 2012 Stillwater Designs PCAMA13MY-A3-20151028
More informationDesigned for 2014 and newer 1500 Series and 2015 and newer Heavy Duty GM Silverado/Sierra Double Cab vehicles
19303116 Designed for 2014 and newer 1500 Series and 2015 and newer Heavy Duty GM Silverado/Sierra Double Cab vehicles Subwoofer Assembly Subwoofer Body Harness 25A Fuse Wire Ties x 6 Wire Taps x 2 Adapter
More informationCONTENTS TOOLS REQUIRED: *Ratchet*13mm Socket*10mm Socket*Phillips Screwdriver*Pliers*Panel Removal Tool. Subwoofer Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N 77KICK40SUBASSEMBLY 1EA. 200 WATT AMP P/N RE08BTL2000R 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER 2EA. T-TAP P/N RFTTAPB 1EA. FUSE 30
More informationCONTENTS TOOLS REQUIRED: *Ratchet*13mm Socket*10mm Socket*Phillips Screwdriver*Pliers*Panel Removal Tool. Subwoofer Installation
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N 77KICK24SUBASSEMBLY 1EA. 200 WATT AMP P/N RE08BTL200R 1EA. POWER HARNESS P/N RHWRANGLERPWR 1EA. OVERLAY HARNESS P/N RHWRANGLER 2EA. T-TAP P/N RFTTAPB 1EA. FUSE 30 AMP
More informationCONTENTS: 1EA. SUBWOOFER HARNESS 2PIECE TOOLS REQUIRED:
CONTENTS: 1EA. SUBWOOFER ENCLOSURE 1EA. SUBWOOFER HARNESS 2PIECE 2EA. T-TAP 1EA. FUSE 30 AMP 6EA. WIRE TIES 1EA. INSTRUCTIONS P/N 77KICK14SUBASSEMBLY P/N RHPM1 P/N RFTTAPB P/N RFUSE30 P/N RFZIP6 P/N RBI77KICK14
More informationCONTENTS TOOLS REQUIRED:
CONTENTS 1EA. SUBWOOFER ASSEMBLY P/N 77KICK13SUBASSEMBLY 1EA. SUB BRACKET P/N 05030060AA 1EA. 200 WATT AMP P/N REBTL200 1EA. AMP BRACKET P/N RMDR 1EA. POWER HARNESS P/N RHRAMP 1EA. OVERLAY HARNESS P/N
More informationAudio System Upgrade Package 2007-UP Jeep Wrangler (Premium Audio) 4-Door & 2- Door Operating and Installation Instructions
2007-UP Jeep Wrangler (Premium Audio) 4-Door & 2- Door Operating and Congratulations, you just purchased one of the most sophisticated 32 bit digital audio amplifiers available today. Fortunately, all
More informationTOOLS REQUIRED: Panel Removal Tool Phillips Screwdriver 10mm Nut Driver Ratchet 10mm Socket 7mm Wrench 7mm Nut Driver Straight Screwdriver
CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N MPDSP039AA 1EA. OVERLAY HARNESS P/N RH41LX10 3EA. 7MM SCREWS P/N RF7MM 6EA. WIRE TIE P/N RFZIP6 1EA. 30 AMP FUSE P/N RFUSE30 1EA. INSTRUCTIONS
More informationImportant! The subwoofer system is designed to be used only with the rear seat in the up position only.
Important! The subwoofer system is designed to be used only with the rear seat in the up position only. CONTENTS 1EA. SUBWOOFER ASSEMBLY 2EA. BRACKET LOWER 2EA. BRACKET UPPER 1EA. OVERLAY HARNESS 2EA.
More informationCONTENTS: TOOLS REQUIRED:
CONTENTS: 1EA. FIVE CHANNEL AMPLIFIER/BRACKET ASSEMBLY P/N RBI77KICK37 1EA. POWER HARNESS P/N RH41PMP 1EA. OVERLAY HARNESS P/N RH41PM 3EA. NUT P/N RFM6NUT 6EA. WIRE TIE P/N RFZIP6 1EA. FUSE 30 AMP P/N
More informationAudio System Upgrade Package Dodge Magnum, Chrysler 300C, Dodge Charger Jeep Commander (Premium Audio Only)
2005-2006 Dodge Magnum, Chrysler 300C, Dodge Charger 2005-2006 Jeep Commander (Premium Audio Only) 2005-2006 Dodge Ram (Regular Cab, Quad Cab, Mega Cab) 2005-2007 Jeep Grand Cherokee (Premium sound) TOOLS
More informationMY F150 CrewCab 1. Tools Required 10X. Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo
2013-2014MY F150 CrewCab 1 Tools Required A B C D E F G 4X H I J K 3X L 3X 2X 10X 2X Page 1 of 15 DL3J-19A014-AA Copyright Ford 2013 FoMoCo 2013-2014MY F150 CrewCab 2 Vehicles with selector lever in floor
More informationCONTENTS TOOLS REQUIRED:
CONTENTS 1EA. FIVE CHANNEL AMPLIFIER P/N MPDSP033AA 1EA. AMPLIFIER BRACKET P/N RM11JK41 1EA. POWER HARNESS P/N RH41JKP 1EA. OVERLAY HARNESS P/N RH41JK 1EA. FUSE 30 AMP P/N RFUSE30 6EA. WIRE TIE P/N RFZIP6
More informationpg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation
RZ3-5KRC RZR XP1000 & 2015+ RZR900 with Ride Command SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers
More informationMY F150 CrewCab 1. Tools Required E F G. Page 1 of 10 9L3J-19A014-AA Copyright Ford 2013 FoMoCo
2009-2014MY F150 CrewCab 1 Tools Required A B C D 3X E F G H 2X I 6X 3X Page 1 of 10 9L3J-19A014-AA Copyright Ford 2013 FoMoCo 2009-2014MY F150 CrewCab 2 Subwoofer Power Wire Routing All Vehicles WARNING:
More informationTOOLS REQUIRED: *Pliers*Panel Removal Tool*Crimpers*Wire Strippers*Ratchet*10mm Socket*#2 Phillips Bit*Drill*18mm socket*19mm socket
CONTENTS: 1EA. SUBWOOFER ASSEMBLY P/N 77KICK20SUBASSEMBLY 1EA. OVERLAY HARNESS P/N RHLX 2EA. LOWER BRACKET P/N RMLX 8EA. #8X1 SCREW P/N RFS81P 2EA. LOCKING NUT 18MM P/N RFLOCKNUT18 2EA. WASHER P/N RFW2
More informationMY F150 SuperCab 1. Tools Required. Page 1 of 12 9L3J-19A014-BA Copyright Ford 2013 FoMoCo
2009-2014MY F150 SuperCab 1 Tools Required A B C D E F G 3X 6X 3X H I J 2X 3X 3X K L M N 3X Page 1 of 12 9L3J-19A014-BA Copyright Ford 2013 FoMoCo 2009-2014MY F150 SuperCab 2 Subwoofer Power Wire Routing
More information*Phillips Screwdriver *10mm Nut Driver *10mm Socket *Ratchet *Three Inch Putty Knife *Panel Removal Tool *10mm Wrench CONTENTS:
TOOLS REQUIRED: *Phillips Screwdriver *10mm Nut Driver *10mm Socket *Ratchet *Three Inch Putty Knife *Panel Removal Tool *10mm Wrench CONTENTS: 1EA. SUBWOOFER ASSEMBLY 1EA. 100 WATT AMP ASSEMBLY 1EA. WIRE
More informationDODGE RAM QUAD CAB. Vehicle Specific Subwoofer Enclosure. Made in the USA
DODGE RAM QUAD CAB Vehicle Specific Subwoofer Enclosure Made in the USA READ ALL DIRECTIONS CAREFULLY BEFORE BEGINNING MOUNTING LOCATION: The enclosure mounts under the rear seat on Dodge Quad Cab Trucks.
More information*Phillips Screwdriver *10mm Nut Driver *8mm Nut Driver*10mm Socket *Ratchet *Three Inch Putty Knife*Panel Removal Tool *10mm Wrench
TOOLS REQUIRED: *Phillips Screwdriver *10mm Nut Driver *8mm Nut Driver*10mm Socket *Ratchet *Three Inch Putty Knife*Panel Removal Tool *10mm Wrench CONTENTS: 1EA. SUBWOOFER ASSEMBLY P/N 05030280AA 1EA.
More informationRZ3-5K Polaris RZR XP 1000 & 900 Kicker 5 Speaker Audio Kit
PO H PWER PO 5 O KIT I E D U A S A TS S I R LA R Z R R O SP pg 2 pg 9 pg 13 pg 25 pg 29 Disassembly, Wire and Amplifier Plate Installation Glovebox Subwoofer Installation Kick Panel Speakers Installation
More informationTOYOTA SIENNA FOG LIGHT (Halogen & LED)
(Halogen & LED) Part Number: TSI-312 / TSI-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Light bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 27363 ODYSSEY Issue Date SEP 2004 PARTS LIST Compact Subwoofer Kit: P/N 08A39-5E1-010 4 Flange bolt, 6 x 12 mm Subwoofer 3 Cushion tapes
More informationPart Number: SFR-713. Hardware Bag Contents. General Applicability All models. Conflicts - Fog Lights. Date: SCION FRS LED DRL
Date: 01.30.2014 SCION FRS 2013-2015 LED DRL Part Number: SFR-713 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware
More informationPart Number: TTU-BGB14-DRL TTU-BGP14-DRL
11/15/16 TOYOTA TUNDRA 2014-17 Billet Grille w/led DRL Part Number: TTU-BGB14-DRL TTU-BGP14-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card 5 2 Hardware
More informationTOYOTA PRIUS FOG LIGHT (Halogen or LED)
Part Number: TPR-413 / TPR-813 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Lower Grill 3 1 Switch Assembly 4 1 Fog Light Operation guide 5 1 Harness Bag Hardware Bag Contents Item
More informationYour Legal Fuel Tank Source.
February 23, 2015 IS# 808 Page 1 of 13 THANK YOU FOR PURCHASING A TRANSFER FLOW 40 GALLON TOOLBOX REFUELING SYSTEM. PLEASE READ THE FOLLOWING PROCEDURES CAREFULLY BEFORE STARTING THE INSTALLATION. CAUTION:
More informationTOYOTA COROLLA LED DRL eyebrow. Part Number: TCO-DRL
Part Number: TCO-DRL Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware Bag Contents Item # Quantity Reqd. Description
More informationSCION FRS FOG LIGHTS. Part Number: SFR-313
Part Number: SFR-313 Kit Contents Item # Quantity Reqd. Description 1 2 Light Housings 2 2 Fog Light bezels 3 1 Harness bag 4 1 User s card 5 1 Switch 6 1 Fuse jumper Hardware Bag Contents Item # Quantity
More informationTOYOTA PRIUS V LED DRL Black-Out
TOYOTA PRIUS V 2012 - LED DRL Black-Out Part Number: 00016-47021 Accessory Code:LDBO10 Conflicts Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box
More informationTOYOTA TACOMA LED DRL. Part Number: TTA-712
Part Number: TTA-712 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware Bag Contents Item # Quantity Reqd. Description
More informationPart Number: TBL-016S
5/18/17 TOYOTA TUNDRA 2014-2017 LED Truck Bed Light Kit Part Number: TBL-016S Kit Contents Item # Quantity Reqd. Description 1 2 LED Bed Light Harness (10 ) 2 2 LED Bed Light Harness (5 ) 3 1 Y Harness
More informationPart Number: STC-501. Hardware Bag Contents. General Applicability. Conflicts. Date: SCION tc LED DRL in FOG LIGHT HOUSING
Date: 09.30.2013 SCION tc 2011-2013 LED DRL in FOG LIGHT HOUSING Part Number: STC-501 Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL housings 2 2 Bezels 3 1 Driver Box 4 1 Harness bag 5 1 User
More information2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH
2015+ S550 MUSTANG Battery Relocation Kit WR-BTRYRELOKIT-LH WR-BTRYRELOKIT-RH The Watson Racing Battery Relocation Kit is NOT designed to protect you in the case of an accident, and therefore is INTENDED
More informationCAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc
Doc. 02.126.00 TOYOTA CAMRY PIO / DIO Rev. A 2013-02/26/13 STRIP LED DRL Part Number: 00016-32280 Accessory Code: LDRS10 Conflicts - Only works on Camry SE Kit Contents Item # Quantity Reqd. Description
More informationConflicts. TOYOTA Prius Foglights. Part Number: Accessory Code: LF1. Factory Fog Lights
TOYOTA Prius 2011- Foglights Part Number: 00016-47401 Accessory Code: LF1 Conflicts Factory Fog Lights Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Fog Lamp s bezels 3 1 Switch Assembly 4 1 Fog
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: 2. APPLICATION: 3. PART NUMBER(S) REQUIRED FOR INSTALLATION: 4. KIT CONTENTS: Item Qty. Fog Lamp Kit Titan MY16 999F1 W4000 Fog Lamp Kit Part Description
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 26031 2004 ODYSSEY Issue Date AUG 2003 NOTE: You cannot install the subwoofer in a vehicle equipped with both an under seat Navigation
More informationRZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit
RZ3-5A Polaris RZR XP 1000 & 900 SSV Works 5 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25
More informationTOYOTA SIENNA LED DRL Black-Out
TOYOTA SIENNA 2013 - LED DRL Black-Out Part Number: 00016-08021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver
More informationConflicts - Fog Lights
TOYOTA CAMRY 2013 - BLACKOUT LED DRL Part Number: 00016-32270 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationTRAIL CHARGER with EXTENDER and COMBO NOSE BOX
TRAIL CHARGER with EXTENDER and COMBO NOSE BOX 284424 01 Version 1.02 03/14/2011 Owners Manual Operation Installation Wiring Diagram Troubleshooting Parts Breakdown 1 GENERAL OPERATION PROBLEM On applications
More informationPHASE 3 POWERSPORTS AUDIO KIT RZR POLARIS. pg 2 Disassembly, Wire and Amplifier Plate Installation. pg 9 Glovebox Subwoofer Installation
POLARIS RZR PHASE 3 POWERSPORTS AUDIO KIT pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25 MRB3 and Dash Kit Installation
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationFORD F-150 CREW CAB. Vehicle Specific Subwoofer Enclosure. Made in the USA
FORD F-150 CREW CAB Vehicle Specific Subwoofer Enclosure Made in the USA READ ALL DIRECTIONS CAREFULLY BEFORE BEGINNING MOUNTING LOCATION: The enclosure mounts under the rear seat on drivers side of Ford
More informationSCION xb HEADREST DVD RSE Section I Installation Preparation. Part Number: PT
Section I Installation Preparation Part Number: PT900-52080 Kit Contents Item # Quantity Reqd. Description 1 2 DVD Headrest Unit 2 2 Headrest Extension Cables 3 1 Audio Interface Module 4 1 Audio Interface
More informationTOYOTA TACOMA LED DRL Black-Out
TOYOTA TACOMA 2013 - LED DRL Black-Out Part Number: 00016-35021 Accessory Code: LDBO10 Conflicts - Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 1 Driver Box 3 1 Harness bag
More informationPart Number: TCA-712SE
Date: 09.04.2013 TOYOTA CAMRY SE 2012-14 LED DRL Part Number: TCA-712SE Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Cushion
More informationLEXUS CT 200h ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT922-89100 Kit Contents Item # Quantity Req'd. Description 1 1 Door Sill, Front Right Hand 2 1 Door Sill, Front Left Hand 3 1 Door Sill, Rear Right Hand 4 1 Door Sill, Rear Left
More informationPart Number: TCO-DRL. Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL. Hardware Bag Contents.
Date: 09.30.2013 TOYOTA COROLLA 2011-2012 LED DRL eyebrow Part Number: TCO-DRL Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: Trailer Hitch Harness Kit 2. APPLICATION: Pathfinder and QX60 3. PART NUMBER: 999T8 XZ000 - Trailer Hitch Harness Kit 4. KIT CONTENTS: Item QTY Description
More informationPart Number: TTA-712. Hardware Bag Contents. General Applicability All models
Date: 09.30.2013 TOYOTA TACOMA 2012-15 LED DRL Part Number: TTA-712 Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware
More informationTOYOTA TACOMA FOG LIGHT (Halogen or LED)
Part Number: TTA-312 / TTA-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Switch Assembly 3 1 Fog light operation guide 4 1 Harness bag Hardware Bag Contents Item # Quantity Reqd.
More informationInstallation Instructions
Installation Instructions Accessories, Electric Trailer Brake Controller Ver 1.0 Page 1 of 9 August 2009 Accessory Development SUBJECT ELECTRIC TRAILER BRAKE CONTROLLER - P/N 82 11 0 420 082 MODEL X5 (E70):
More informationGN-3A Polaris General SSV Works 3 Speaker Audio Kit
GN-3A Polaris General SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 17 Kick Panel Speakers Installation pg 21 MRB3 and Dash
More informationINSTRUMENT PANEL ASSEMBLY
2003 Dodge or Ram Truck RAM 1500 Truck 2WD V8-4.7L VIN N Vehicle > Body and Frame > Interior Moulding / Trim > Dashboard / Instrument Panel > Service and Repair > Removal and Replacement INSTRUMENT PANEL
More informationTOYOTA VENZA 2009 TRAILER WIRE HARNESS Procedure
Part Number: PT791-0T099 Kit Contents Item # Quantity Reqd. Description 1 1 Trailer Wire Harness Module 2 1 4-Flat Harness 3 1 Battery Power Wire Harness 4 1 Mounting Bracket, 4-Flat 5 2 Screw #10-24 6
More informationRZ3-3A Polaris RZR XP 1000 & 900 SSV Works 3 Speaker Audio Kit
RZ3-3A Polaris RZR XP 1000 & 900 SSV Works 3 Speaker Audio Kit pg 2 Disassembly, Wire and Amplifier Plate Installation pg 9 Glovebox Subwoofer Installation pg 13 Kick Panel Speakers Installation pg 25
More informationInstallation instructions, accessories. Subwoofer
Installation instructions, accessories Instruction No 9162298 Version 1.0 5 Part. No. Subwoofer Volvo Car Corporation Subwoofer - 9162298 - V1.0 Page 1 / 24 Equipment A0000162 A0801178 A0000161 R8802817
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1. 2. 3. 4. DESCRIPTION: APPLICATION: PART NUMBER: KIT CONTENTS: Trailer Hitch Harness Kit Infiniti JX 999T8 YZ000- Trailer Hitch Harness Kit Item QTY Description
More informationDASH AUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 04/16 Page 1 of 6. Verify accessory fitment at Polaris.com.
DASH AUDIO KIT P/N 2882030 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationLED Fog Light. Conflicts Note: 1226, General Applicability Fits Models Additional Items Required For Installation
LED Fog Light Year & Model Part Number Conflicts Note: 1226, 1228 2017 Prius TPR-817 General Applicability Fits Models 1221 1225 1223 1227 1224 Additional Items Required For Installation Items 1 N/A 2
More informationTOYOTA PRIUS C FOG LIGHT (Halogen & LED)
TOYOTA PRIUS C 2012-14 FOG LIGHT (Halogen & LED) Part Number: TPC-312 / TPC-812 Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 2 Bezels 3 1 Switch Assembly 4 1 Fog Light Operation guide
More informationAccessory Kit Estimated Fitting Time: 120 Minutes (Prado) Estimated Fitting Time: 140 Minutes (Kluger)
Tow-Pro Wiring Kit - Toyota Kluger / Prado Accessory Kit Estimated Fitting Time: 0 Minutes (Prado) Estimated Fitting Time: 0 Minutes (Kluger) FI99 Page 0 of Issue: Date: 0/0/0 0 General Notes Read through
More informationInstallation Instructions for Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights
Installation Instructions for 2015-2018 Chevrolet Colorado, GMC Canyon, LT, Z71, With Factory Fog Lights This kit is designed to allow use of your factory fog light operation along with an addition auxiliary
More information2013 Road King CVO FLHRSE5 Detachable Fairing w/ Garmin Zumo 665 Installation Instructions
2013 Road King CVO FLHRSE5 Detachable Fairing w/ Garmin Zumo 665 Installation Instructions 1 1. Turn ignition switch to on position and leave there. This will prevent alarm from going off when you disconnect
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More informationTOYOTA TACOMA XSP-X LED DRL. Part Number: Accessory Code: LDRL10
TOYOTA TACOMA 2013 - XSP-X LED DRL Part Number: 00016-35230 Accessory Code: LDRL10 Conflicts -None Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Harness bag 4 Hardware Bag
More informationPN DODGE CORONET Two panel Sequential LED Taillight kit installation guide. Kit Contents:
1969 DODGE CORONET Two panel Sequential LED Taillight kit installation guide Kit Contents: 2 LED panels 4 rubber grommets 1 power wire with t-tap 1 driver side LED harness, 24 1 passenger side LED harness,
More informationPart Number: T4R-2N1. Hardware Bag Contents. General Applicability Models with factory fog light. Conflicts -
Date: 07.30.2015 TOYOTA TUNDRA 2014-2016 LED Fog Light & DRL 2 in 1 Part Number: T4R-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User
More informationINTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE
Page 1 of 18 2016 Dodge Grand Caravan 3.6L Eng VIN G SE Service Manual: BODY - INTERIOR & EXTERIOR Print Date: INTERIOR > CONSOLE, FLOOR > REMOVAL > REMOVAL > BASE FLOOR CONSOLE Fig 1: Base Floor Console
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Models: 7105 & 7105TK Dodge Ram 1500 ('02 Current) Ram 2500 & 3500 '03 - Current with stock manual mirrors. IF YOU DO NOT CURRENTLY HAVE MANUAL MIRRORS, THE WRONG SET HAS BEEN
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationTOYOTA TACOMA Part Number: TTA-BGB16-DRL TTA-BGP16-DRL
TOYOTA TACOMA 2016-17 Date: 10.29.2016 Billet Grille w/led DRL Part Number: TTA-BGB16-DRL TTA-BGP16-DRL Kit Contents Item # Quantity Reqd. Description 1 2 LED DRL 2 1 Driver Box 3 1 Switch 4 1 User Card
More informationPart Number: TTA-2N1. Hardware Bag Contents. General Applicability SR5, TRD Sport, TRD Off-Road, Limited
Date: 2.10.2016 TOYOTA TACOMA 2016-2 in 1 LED UPGRADE KIT Part Number: TTA-2N1 Kit Contents Item # Quantity Reqd. Description 1 2 DRL + Fog Light Housing 2 1 Driver Box 3 1 Harness bag 4 1 User s card
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 22903-22963 ODYSSEY Issue Date MAY 2002 PARTS LIST Subwoofer Kit: P/N 08A39-EP7-100 Subwoofer 2 Cushion tapes 8 Wire ties (1 not used)
More informationStand Alone Fog Lights Installation Instructions
Tools Required: 1. Trim Removal tool or protected flat screwdriver 2. #2 Phillips Screwdriver 3. 10mm socket 4. 10mm wrench 5. 8mm or 5/16 socket 6. Adjustable Pliers 7. Electrical Tape WARNING!!! Disconnect
More informationRECOMMENDED SEQUENCE OF APPLICATION
08-11 DODGE CARAVAN, NITRO, JOURNEY CHRYSLER TOWN & COUNTRY/ JEEP LIBERTY 09-11 DODGE RAM 1500/ DAKOTA NEW BODY PART NUMBER: 250-9001 KIT CONTENTS ITEM QTY DESCRIPTION 1 1 CRUISE CONTROL SWITCH/HARNESS
More informationINSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS 1 DESCRIPTION: Trailer Tow Harness 2 APPLICATION: Nissan Rogue 3 PART NUMBER: 999T8 G2000 4 KIT CONTENTS: 999T8 G2000 Item Qty. Part Description Service Part Number
More informationTOYOTA TACOMA FOG LIGHT
TOYOTA TACOMA 2012 - FOG LIGHT Part Number: 00016-35220 Accessory Code: LF10 Conflicts - Factory Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 Fog Lamps 2 1 Hardware bag 3 1 Switch Assembly
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. SYSTEM 2005 ACCORD All 27511 (DX, LX) 2-AND 4-DOOR Issue Date AUG 2004 PARTS LIST Security System Attachment (LX): P/N 08E55-SDA-100A Unit
More information1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide
1970 DODGE CHALLENGER Four panel Sequential LED Taillight kit installation guide Kit Contents: 4 LED panels 4 rubber grommets 1 power wire with t-tap 2 driver side LED harnesses, 24 2 passenger side LED
More informationINSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE
INSTALLATION INSTRUCTIONS FOR THE TOMAHAWK ELECTRIC REVERSE LAST UPDATED: April 2018 Thank you for choosing the Motor Trike Electric Reverse. We ask that you read the directions before you start and follow
More information