Phillips Screwdriver 10mm Nut Driver 8mm Nut Driver10mm Socket Ratchet Three Inch Putty KnifePanel Removal Tool 10mm Wrench

Size: px

Start display at page:

Download "*Phillips Screwdriver *10mm Nut Driver *8mm Nut Driver*10mm Socket *Ratchet *Three Inch Putty Knife*Panel Removal Tool *10mm Wrench"

Joleen Montgomery
6 years ago
Views:

1 TOOLS REQUIRED: *Phillips Screwdriver *10mm Nut Driver *8mm Nut Driver*10mm Socket *Ratchet *Three Inch Putty Knife*Panel Removal Tool *10mm Wrench CONTENTS: 1EA. SUBWOOFER ASSEMBLY P/N AA 1EA. 200 WATT AMPLIFIER P/N AC 1EA. WIRE HARNESS P/N RH05CHGSUBM 2EA. M6 BOLT P/N RFM6 1EA. VEHICLE TO SUB BRACKET P/N AB 1EA. BODY CLIP P/N AA 1EA. INSTRUCTIONS P/N RBI05CHGSUB 6EA. WIRE TIES P/N RFZIP6 4EA. #8 SHEET METAL SCREWS P/N RFS2 77KICK04 01/09/07 Page 1 of 8

1. Remove the lower rear seat cushion by pulling up on the front edge. 2. Fold rear seat backs into the down position. 3.

Release the spring clip on the back of the side cushion.

2 5. To remove the rear package tray, first remove the plastic retainer in the center.

If the car is equipped with a eight speaker Boston Acoustics system find the subwoofer mounted in the rear deck and remove

2 1. Remove the lower rear seat cushion by pulling up on the front edge. 2. Fold rear seat backs into the down position. 3. Remove the 10mm bolt securing the side portions of the seat. Fig Release the spring clip on the back of the side cushion. Insert a putty knife behind the side cushion and push down firmly while pulling forward on the cushion. Fig. 2 Fig. 1 Fig To remove the rear package tray, first remove the plastic retainer in the center. Remove the package tray by pulling it away from the rear glass. Fig If the car is equipped with a eight speaker Boston Acoustics system find the subwoofer mounted in the rear deck and remove the four screws securing it in place. Save the screws for reinstallation later. 7. If the car is not equipped with the Boston Acoustics system the hole will be covered by a selfadhesive sound damping material. Remove the damping material and save for reinstallation later. Fig. 4 Fig. 3 Fig. 4 77KICK04 01/09/07 Page 2 of 8

8. Install the amplifier assembly in the hole in the rear deck.

Secure the amplifier assembly using the previously removed screws.

the factory subwoofer. Fig. 6 Fig. 5 Fig. 6 10.

3 8. Install the amplifier assembly in the hole in the rear deck. Fig Secure the amplifier assembly using the previously removed screws. Screws (#8 sheet metal) are provided for cars not equipped with the factory subwoofer. Fig. 6 Fig. 5 Fig Replace the sound damping material (if so equipped) over the amplifier assembly. Fig Remove the six plastic retainers securing the large panel directly below the package tray and remove the panel from the trunk. Fig. 8 Fig. 7 Fig. 8 77KICK04 01/09/07 Page 3 of 8

12. Plug the ten pin connector of the wire harness into the

Remove the plastic retainer securing the right side of the trunk

right side of the rear seat pass through and toward the battery

4 12. Plug the ten pin connector of the wire harness into the amplifier. Fig Remove the plastic retainer securing the right side of the trunk liner to the floor to allow for wire routing. Fig. 10 Fig. 9 Fig Route the power and ground portion of the wire harness down the right side of the rear seat pass through and toward the battery along side the factory wiring using the supplied wire ties where needed. Fig Secure the harness with the factory retaining bracket. Fig. 12 Fig. 11 Fig KICK04 01/09/07 Page 4 of 8

16. Connect the ground wire to the body of the car at the factory ground point

Connect the power wire to the fuse box main lug. Fig. 14 Fig. 13 Fig. 14 18.

the white male speaker connector into the white female connector of the wire

On all other cars disconnect the left rear speaker connector. Plug harness.

5 16. Connect the ground wire to the body of the car at the factory ground point between the fuse box and the battery. Fig Connect the power wire to the fuse box main lug. Fig. 14 Fig. 13 Fig If the car is equipped with the eight speaker Boston Acoustics system, connect the white male speaker connector into the white female connector of the wire harness. Fig On all other cars disconnect the left rear speaker connector. Plug the white male speaker connector into the white female connector of the wire harness. Plug the white male connector back into the speaker. Fig. 16 Fig. 15 Fig KICK04 01/09/07 Page 5 of 8

20. You will need to remove the plastic fastener in order to correctly position

Route the speaker output portion of the harness toward the left rear fender well

The wire harness needs to route low enough that it will not be pinched by the

Install the speed clip that is provided onto the sheet metal just behind the left

6 20. You will need to remove the plastic fastener in order to correctly position the wire harness. It is not necessary to reinstall this fastener. Fig Route the speaker output portion of the harness toward the left rear fender well and back to the subwoofer mounting location. The wire harness needs to route low enough that it will not be pinched by the subwoofer mounting bracket. Fig. 18 Fig. 17 Fig Install the speed clip that is provided onto the sheet metal just behind the left rear fender well. Fig Install the subwoofer mounting bracket using one of the supplied M6 bolts. Fig. 20 Fig. 19 Fig KICK04 01/09/07 Page 6 of 8

24. Remove the bag from the subwoofer assembly and lay it in the corner of the

The purpose of the bag is to prevent the Velcro mounting system on the bottom of

Set the subwoofer assembly in place, install the M6 bolt and tighten. Fig. 22 26.

7 24. Remove the bag from the subwoofer assembly and lay it in the corner of the trunk where the subwoofer assembly will be placed. The purpose of the bag is to prevent the Velcro mounting system on the bottom of the subwoofer assembly from engaging the carpet prematurely. Fig Set the subwoofer assembly in place, install the M6 bolt and tighten. Fig Connect the four pin connector of the wire harness to the subwoofer assembly. Fig. 21 Fig Apply moderate pressure to the front of the enclosure while pulling the bag out from under it. Fig Reinstall all previously removed parts in reverse order. Fig KICK04 01/09/07 Page 7 of 8

7 output - Pin 8 ground Pin 9 empty Pin 10 empty F U S E + - Battery Pin 1

8 Pin 1 signal + Pin 2 empty Pin 3 signal - Pin 1 12 volt input Pin 2 signal input - Pin 3 signal input + Pin 4 output + Pin 5 output Pin 6 output + Pin 7 output - Pin 8 ground Pin 9 empty Pin 10 empty F U S E + - Battery Pin 1 output + Pin 2 output Pin 3 output + Pin 4 output - 77KICK04 01/09/07 Page 8 of 8

Phillips Screwdriver 10mm Nut Driver 10mm Socket Ratchet Three Inch Putty Knife Panel Removal Tool *10mm Wrench CONTENTS:

TOOLS REQUIRED: *Phillips Screwdriver *10mm Nut Driver *10mm Socket *Ratchet *Three Inch Putty Knife *Panel Removal Tool *10mm Wrench CONTENTS: 1EA. SUBWOOFER ASSEMBLY 1EA. 100 WATT AMP ASSEMBLY 1EA. WIRE