NEW SINGLE-HEAD MACHINE TMBR-SC TMBP-SC TECHNICAL SUMMARY

Size: px

Start display at page:

Download "NEW SINGLE-HEAD MACHINE TMBR-SC TMBP-SC TECHNICAL SUMMARY"

Branden Cross
5 years ago
Views:

1 Ref.. TTD March, 2016 TAJIMA TECHNICAL DOCUMENT NEW SINGLE-HEAD MACHINE TMBR-SC TMBP-SC TECHNICAL SUMMARY ( )

2 FOREWORD We have started the mass-production of the new Single-head machines [ TMBR-SC ], [ TMBP-SC ] (hereinafter called "TMBR/TMBP") since December [ TMBR/TMBP ] enhances the quality of embroidery finish and functionality in the equivalent or higher level to the conventional Single-head machines. Besides, there are widely differences between the conventional machines and [ TMBR/TMBP ] in the electrical component parts as well as in the mechanical parts. This document describes the features, specification comparison of [ TMBR/TMBP ] and also the information of electrical components parts. You are kindly requested to clearly understand of [ TMBR/TMBP ], referring to this document. Contents 1. Features of TMBR/TMBP Individual drive mechanism of presser foot (Only for TMBR) New type Cylinder bed Operation panel, I/O port Tension base Snap-fit middle thread guide Cap frame base Lightweight FS mode System software 4 2. Specification comparison 5 3. Allocation of major electrical component parts 7 4. Compatibility of electrical component parts 8 5. Electrical system diagram Electrical system diagram Harness list Compatibility of major parts TMBR-SC Cylinder bed (E1-03) Color change system (E1-04) Arm 1 (E1-05-1) Arm 2 (E1-05-2) Arm 3 (E1-05-3) Needle bar case 1 (E1-06-1) Needle bar case 2A [6-needle M/C] (E1-06-2a) Needle bar case 2B [12, 15-needle M/C] (E1-06-2b) TMBP-SC Arm 1 (E2-05-1) Arm 2 (E2-05-2) Arm 3 (E2-05-3) Needle bar case 1 (E2-06-1) Needle bar case 2A [6-needle M/C] (E2-06-2a) Needle bar case 2B [12, 15-needle M/C] (E2-06-2b) Upper thread holder (E2-07) 39 Page ( i )

TMBR ] has adopted the new mechanism to individually drive the

foot). DCP has been adopted to[ TMAR series TYPE-2 ].

pulse motor to provide the embroidery finish in high quality.

thread holding motor te) The Needle bar reciprocator for MX

Presser foot reciprocator TMBR-SC internal view of 47mm arm

slimmer cylinder bed compared with that of conventional

3 1. Features of TMBR/TMBP 1-1. Individual drive mechanism of presser foot (Only for TMBR) [ TMBR ] has adopted the new mechanism to individually drive the presser foot on 47mm arm (DCP : Digitally-Controlled Presser foot). DCP has been adopted to[ TMAR series TYPE-2 ]. It accurately controls the height of presser foot by using the pulse motor to provide the embroidery finish in high quality. For [ TMBP ], the mechanical type presser foot is equipped in the same mechanism with that of TUMX-C. Jump motor Needle bar reciprocator Presser foot motor Upper thread holding motor te) The Needle bar reciprocator for MX type machines cannot be used to [ TMBR/TMBP ]. Presser foot reciprocator TMBR-SC internal view of 47mm arm 1-2. New type Cylinder bed [ TMBR/TMBP ] has adopted the slimmer cylinder bed compared with that of conventional machine to locate the embroidery material closer to the needle plate when using the cap frame. The new cylinder bed requires an exclusive gauge to adjust the lower dead point. 13.3mm Lower dead point gause for new cylinder bed ( ) 13.3mm Lower dead point gause for TUMX-C ( ) 44mm 55mm TMBR/TMBP Needle plate for new cylinder bed (2mm dia. or 2.5mm dia. hole) TUMX-C Needle plate for TUMX-C ( 1 / 40 )

1-3. Operation panel, I/O port [ TMBR/TMBP ] has equipped 7 inch

5 inch in actual display area) for the new operation panel.

machine to enhance the convenience of connection.

7 inch wide LCD LAN port Start/stop buttons Right side of machine

Tension base On the tension base for [ TMBR/TMBP ], the magnetic

reduce the malfunction because of the dust such as lint.

will be introduced by turns to the new models in the future.

4 1-3. Operation panel, I/O port [ TMBR/TMBP ] has equipped 7 inch wide LCD display (6.5 inch in actual display area) for the new operation panel. For the panel operation, the same user interface with MX type series has been succeeded. The locations of USB and LAN ports have moved to the right side of machine to enhance the convenience of connection. The operation of machine start/stop is performed with the buttons on the operation panel. Power supply switch and USB ports Operation panel (XC1 controller) 7 inch wide LCD LAN port Start/stop buttons Right side of machine te) USB ports support the multiple connection of the USB memory and barcode reader. 2 USB memory devices cannot be used at the same time Tension base On the tension base for [ TMBR/TMBP ], the magnetic type sensor has been adopted for the thread breakage detection to reduce the malfunction because of the dust such as lint. This new sensor has been adopted to TMAR series TYPE-2 as well and will be introduced by turns to the new models in the future. Tension base switch is not mounted onto the tension base like that of TEJT2-C. Neodymium magnet TC sensor (Magnetic type) Slit disc Tension base card Internal view of tension base for TMBR/TMBP TC sensor (Optical type) Internal view of tension base for the conventional machine ( 2 / 40 )

1-5. Snap-fit middle thread guide We have further improved [ One-touch type

conventional TMAR series, and we have now introduced it to [ TMBR/TMBP ] as [

te) [ Snap-fit middle thread guide ] is mounted for 9/12/15-needle machines.

Major features - To facilitate attachment/detachment of device by fixing with

) - To facilitate to adjust the stroke of thread take-up spring by using the

mounting, insert the pawl into a hole and push down middle thread guide base.

straight pins to the middle thread guide base.

Standard 0.5 dia. For thick thread For the mounting, insert the lock pawl first.

5 1-5. Snap-fit middle thread guide We have further improved [ One-touch type middle thread guide ], having been adopted to TFGNII series as well as to the conventional TMAR series, and we have now introduced it to [ TMBR/TMBP ] as [ Snap-fit middle thread guide ]. te) [ Snap-fit middle thread guide ] is mounted for 9/12/15-needle machines. For 6-needle machine, [ One-touch type middle thread guide ] is mounted. Major features - To facilitate attachment/detachment of device by fixing with the locking pawl (On-touch type middle thread guide is fixed with the screw.) - To facilitate to adjust the stroke of thread take-up spring by using the notch type adjuster (7 steps) Exterior view, adjustment points For the mounting, insert the pawl into a hole and push down middle thread guide base. Pawl Straight pins Middle thread guide base Lock pawl For the mounting, set the straight pins to the middle thread guide base. Large thread holder Thread take-up spring Wire dia. (mm) Spec. 0.4 dia. Standard 0.5 dia. For thick thread For the mounting, insert the lock pawl first. For the removing, unlock the lock pawl with flathead screwdriver etc. large Stroke Small Spring shaft (Standard position) To adjust the stroke, turn the spring shaft by 1 notch with a coin etc. ( 3 / 40 )

1-6. Cap frame base On [ TMBR/TMBP ], we have improved the cap frame base with the improvement of cylinder bed.

Rotation shaft Exterior view of cap frame base for the slim type cylinder Front view of cap frame base for the slim type cylinder te) The cap frame base is in common with TMAR-KC TYPE2.

Lightweight On [ TMBR/TMBP ], for the easier machine installation and relocation, redesign the machine stand and reduce the quantity of electrical component parts to reduce the machine weight.

FS mode [ TMBR/TMBP ] supports "FS mode", having been adopted to TFGNII and TMAR series Type2.

6 1-6. Cap frame base On [ TMBR/TMBP ], we have improved the cap frame base with the improvement of cylinder bed. The rotation shaft for the cap frame base is mounted onto the bottom side of cylinder bed to stabilize the cap frame embroidery. The conventional cap frame can be used to the new cap frame base. Rotation shaft Exterior view of cap frame base for the slim type cylinder Front view of cap frame base for the slim type cylinder te) The cap frame base is in common with TMAR-KC TYPE2. (The photos shown above are the Cap frame base on TMAR-KC TYPE2) 1-7. Lightweight On [ TMBR/TMBP ], for the easier machine installation and relocation, redesign the machine stand and reduce the quantity of electrical component parts to reduce the machine weight. The machine vibration and stability of needle location are equivalent to TUMX-C. Model TMBR/TMBP TUMX-C Weight 95kg 102kg 1-8. FS mode [ TMBR/TMBP ] supports "FS mode", having been adopted to TFGNII and TMAR series Type2. "FS mode" is effective to enhance the embroidery finish with the metallic yarn or loose twisted thread and it can be set in units of needle bar. te) The maximum R.P.M. will be limited up to 900rpm (4mm) when "FS mode" is selected and it may vary depending on the stitch length being embroidered System software The system software for [ TMBR/TMBP ] can be installed through USB memory in the same manner with that of conventional MX type series. In the system installation, the firmware, memorized in the cards, can be updated as well as the system software. The version name of the system software and firmware can be checked on the panel screen. Check the version name in [ SET ] +F4- [ 8 Software Version ] ( 4 / 40 )

7 2. Specification comparison Item TMBR/TMBP TUMX-C TEJTII-C Machine code (Type) TMBR : E1 (1-1A) TMBP : E2 (1-1A) MU (1-1A) JT (1-1A) Number of needles 6/12/15 needles 6/15 needles 6/9/12/15 needles Maximum embroidery space (X*Y) 500* *360/500* *360 Arm Maximum R.P.M Needle bar stroke 47mm 50mm Presser foot drive TMBR : Pulse motor (DCP) Mechanical system TMBP : Mechanical Border/tubular 1200rpm (4mm) 1200rpm (*1) 1200rpm Width of cylinder bed (Width of needle plate bracket) Standard rotary hook Cap frame 1000rpm (4mm) 900rpm 45mm (44mm) Regular E-hook, supporting thick thread FS (KHS12-RYPTFSOE) 56mm (55mm) Regular hook (HSL-ATR [ MTQETA]) Screen LCD (7 inch wide) LCD (6.5 inch) LCD (20-digit, 4-line) Operation Windows Embedded Windows CE 5.0 System OS panel Compact 7 (English) (Japanese/English) ITron System recording medium SD card CF card Built-in memory Main shaft motor (Upper shaft reduction ratio) AC servo 188W (1:2.5) AC servo 200W (1:2.5) AC servo 120W (1:2) [ Direct coupling ] X-axis motor 60mm square pulse motor (Direct coupling 1:1) Y-axis motor 60mm square pulse motor (Reduction ratio 1:3.5) Upper thread locking device Installed t installed Middle thread guide Snap-fit type (*2) Roller types Needle base LED light Installed (*3) Installed Thread breakage detection type Magnetic type Optical type Tension base switch t mounted Mounted t mounted Design data input/output USB, LAN Serial, USB, LAN FS mode Supported t supported Network Supported Time limit locking type AR/GN type MX type (User management system) (Password maker) t supported System boot up lock (*4) Supported t supported Barcode input (*5) Supported System boot up time 40 sec. 105 sec. 8 sec. Sleep mode t supported Supported t supported System installation medium USB USB, floppy disk Timing Power supply specification Stop position Main shaft adjusting position Upper dead point 100+/-2 deg to deg. 0 deg. Lower dead point 178 deg. 180 deg. Needle/rotary hook ATH Take-up lever lower dead point Voltage (1-phase) Power consumption 200+/-1 deg. 287+/-1 deg. 297+/-2 deg. 100 to 120V/200 to 240V (50/60Hz), 120V (Only for UL spec.) TMBR : 160W 230W 225W TMBP : 190W Weight 95kg 102kg 75kg (*1) Only for the tubular frame because the border frame not supported (*2) One-touch type middle thread guide is mounted only to 6-needle machine. (*3) ON/OFF operation on the operation panel (*4) A function to enable the machine operation by cancelling the password lock at machine installation after shipping (*5) Barcode reader with USB connection (commercial item) is required separately. ( 5 / 40 )

8 Optional frame Optional device Item TMBR/TMBP TUMX-C TEJTII-C Cap frame Common part with other models (*6) Common part with other models Cylindrical frame t supported Supported Border frame (X*Y) Supported (500*350) t supported Supported (500*350) Auto clamp frame Supported (Air type) Supported X-extension unit To be supported in the Supported t supported (X*Y) future (1200*350) (1200*350) Beam sensor Supported LED light (fluorescent type) Supported t supported Position marker Supported Supported (*7) Multi cord device TMBR : Supported TMBP : t supported t supported Stand Supported Stand tray Supported t supported Serial communication (RS-232C) t supported Supported (*8) Sequin device III t supported Sequin device IV Supported Laser line marker(*9) t supported Signal tower To be supported Supported t supported in the future Under thread t supported t supported (*10) winder (Built-in) Lochrose embroidery device Supported t supported Laser device, made by other t supported suppliers Boring device (Mechanical type) t supported Supported (*6) Exclusive cap frame base for the slim cylinder (*7) Position marker cannot be mounted with the cap frame. (*8) Standard specification (*9) A device to mark the needle position from the bottom of needle bar (*10) t equipped since October 2013 ( 6 / 40 )

9 3. Allocation of major electrical component parts CMOS battery(lithium battery) Jump motor Upper thread holding motor Presser foot motor CPU card Internal view of arm Beam sensor (Option) ise filter SD card (On the back side of card) Internal view of Operation panel (XC1 controller) Emergency stop switch Power supply switch (Circuit protector) ATH sensor USB hub card AC inlet ATH motor Connector A card On the left side of machine stand Internal view on the rear side of machine stannd LAN port USB ports Color change motor Color change potentiometer TC sensor (Magnetic type) Control card Permanent counter X-axis motor Main shaft driver 24V power supply Y-axis motor Upper side of machine stand Fan Main shaft motor ( 7 / 40 )

10 4. Compatibility of electrical component parts : New part : Available : t available Cards Sensor, switch (SW) Power supply Motor Solenoid Optional device Category Part name Part. BR/BP TUMX Remark Operation panel Input/output Control Tension base Controller :XC1[A] 0J A00 7 inch wide LCD LCD :7 inch Wide NL8048AC19-13 Card :CPU :XC1[A] 0J A00 MP359-1A Lithium Battery :XC[A] A01 CMOS Battery SD Card :XC1 0J MB Class6 Card :Switch :XC1 0J MP361-2A Controller :X16-E[A] 0J A15 LCD :6.5 inch Card :CPU-E :X16[A] 0J A15 The component parts of Lithium Battery English operation panel Compact Flash Memory :English :6.5-inch 0J of TUMX-C are Card :Capacitor 0J described here for the example of comparison. Card :I/F Connector 0J Inverter :Backlight Card :Switch 0J Card :Connector :A 0J MP350-1A, for LAN Card :USB Hub :B 0J MP336-1B, for USB Main Shaft Driver :X14 :200[A] 0J A11 MP348-2B-B Main Shaft Driver :X13-A :200[A] 0J A11 Card :Control 0J MP358-2B Card :Machine 0J C Card :Head 0J AC Card :TC Sensor :Magnetic Type 0J TCS131 Card :Tension Base 0J Card :TC Sensor 0J Card :Power Supply :Single Head 0J DC24AVR is used for the power supply of BR/BP Power supply ATH, X/Y-axis Card :Magnetic Sensor A 0J Main shaft Card :Photo-interrupter 0J Color change Potentiometer Emergency stop SW Switch :Emergency Stop[A] 0J A00 A22E-S-02 with lead wire Switch :Emergency Stop[A] 0J A00 Start/stop SW Switch :Cylinder Head[A] 0J A11 BR/BP: built-in SW in the panel Permanent counter Counter :Electro-Magnetic 0J Circuit Protector :Single-phase 10A F521-P7T1-W02L-10A AC power supply Circuit Protector :Single-phase 10A ise Filter :Single-phase :10A NAP ise Filter :Single-phase :10A AC Inlet DC5V, 12V DC Power Supply :5V +/-12V DC Power Supply :24V :350W OZP JSE-K DC24V DC Power Supply :24V Transformer Transformer :X Servo Motor :188W 0J D2-01 Main shaft Servo Motor :200W 0J X/Y-axis Pulse Motor :60mm Square :With Sensor[A] 0J A14 Presser foot Pulse Motor :42mm Square 44L :With Sensor[A] 0J A03 To be used only for TMBR Jump, Upper thread hold, Pulse Motor :42mm Square :Double-End[T] 0J T11 Color change ATH Pulse Motor :42mm Square :Double-End 0J Fan Motor :Fan :60mm Square 0J Upper thread lock Solenoid :Open Frame Picker Solenoid :Open Frame[A] 0J A11 Needle position Position Marker[A] 0J A22 Safety Sensor :Beam Sensor : Light Lamp :Needle Base LED Light[A] 0J A00 For the needle base Lamp :LED Light :16W 0J LE38B101B, fluorescent type LED ( 8 / 40 )

11 5. Electrical system diagram 5-1. Electrical system diagram AC power supply DC24V DC12V DC5V DC3.3V Control signal (Two-way) Control signal Ground Operation panel (XC1 controller) 7 inch wide LCD panel SD card Windows Compact7 CN1 J13 CPU card MP359 J1 CN1 Switch card MP361 24V power supply OZP JSE-K 6 CN1 J7 J23 Power supply switch (Circuit protector) 3120-F521-P7T1-W02L-10A 5 Emergency stop switch A22E-S-02 2 ise filter NAP CN2 J26 CN7 AC inlet AP B-2-Ni-BLACK J28 J29 CN10 CN11 CN8 CN PE LAN CN2 Connector A card MP350 CN USB Fan Beam sensor Air pressure sensor Backup capacitor ( *1 ) Fluorescent type LED lamp Needle base LED lamp Signal tower ( *1 ) CN Sequin device ( *1 ) CN6 CN9 CN10 Option card MP349 ( *1 ) Machine stand USB hub card MP336 CN5 CN5 CN Control card MP358 CN7 CN3 CN4 CN5 CN10 CN13 CN21 CN6 CN2 CN16 CN1 CN1 SW1 ( *2 ) CN14 CN5 Main shaft driver MP CN8 CN9 CN11 CN15 CN17 CN19 CN20 CN24 CN29 CN30 CN32 CN33 CN34 CN35 CN38 CN39 CN41 CN42 CN43 CN45 CN47 CN48 CN2 CN3 CN Picker solenoid Upper thread lock solenoid Position marker TC sensor Tension base card (Magnetic type) Electro-magnetic counter Color change potentiometer Laser line marker ( *1 ) Foot switch X-axis motor Encoder Color change motor Upper thread holding motor X-axis origin sensor ATH origin sensor ATH motor Y-axis motor Encoder Jump motor Magnetic sensor card Y-axis origin sensor Y-axis origin sensor Magnetic sensor card (For Auto clamp frame) Presser foot motor Encoder Only for TMBR Main shaft motor Encoder Main shaft fixed position sensor Photo-interrupter Power supply cord AC120V (Japanese/ETL) AC230V (EMC) ( *1 ) To be supported in the future ( *2 ) Dip switch settings (SW1). Setting details ON OFF Setting at shipment To be set according 1 Beam sensor Enabled Disabled to the machine specification 2 Position marker -- Enabled OFF 3 Auto clamp frame air valve -- Enabled OFF t used Always OFF ( 9 / 40 )

12 5-2. Harness list. Part name Part. Type, remark 1 Harness :AC inlet - ise filter :ETL H0E For ETL spec. 2 Harness : ise filter - Emergency stop :ETL H0E For ETL spec. 3 Harness :AC inlet grounding :ETL H0E For ETL spec. 4 Harness :ise filter grounding :ETL H0E For ETL spec. 5 Harness :Emergency stop-power supply switch :ETL H0E For ETL spec. 6 Harness :Power supply switch-24v power supply :ETL H0E For ETL spec. 7 Harness :AC inlet-ise filter :CE H0E For EMC spec. 8 Harness : ise filter- Emergency stop :CE H0E For EMC spec. 9 Harness :AC inlet grounding :CE H0E For EMC spec. 10 Harness :ise filter grounding :CE H0E For EMC spec. 11 Harness :Emergency stop - Power supply switch :CE H0E For EMC spec. 12 Harness : Power supply switch -24V power supply :CE H0E For EMC spec. 13 Harness :24V power supply output H0E Harness :Power failure detection H0E Harness :CPU card Control card H0E Harness :CPU card USB Hub card H0E Harness :Controller :Grounding H0E Harness :Control card Main shaft driver H0E Harness :Main shaft fixed position sensor H0E Harness :X-axis junction H0E Harness :X-axis origin sensor H0E Harness :Y-axis motor H0E Harness :Y-axis encoder H0E Harness :Y-axis origin sensor H0E Harness :ATH knife retracting sensor H0E Harness :Color change potentiometer H0E Harness :Upper thread lock solenoid H0E Harness :Picker solenoid H0E Harness :Needle base LED lamp H0E Harness :Permanent counter H0E Harness :Thread breakage sensor H0E Harness :Fan motor H0E Harness :CPU card Connector card :LAN H0E Harness :Beam sensor H0E Harness :Position marker H0E Harness :Air pressure sensor H0E Harness :Auto clamp :Y-axis frame origin sensor H0E Harness :Auto clamp :Two-steps type foot switch H0E Harness :LED lamp H0E Harness :Presser foot encoder H0E ( 10 / 40 )

13 6. Compatibility of major parts The compatibility of major parts on [ TMBR-SC/TMBP-SC ] is described here. (Excluding the screws) 6-1. TMBR-SC Cylinder bed (E1-03) Symbol Upward compatibility TUMX-C TEJT2-C ( 11 / 40 )

14 Symbol. Part name Part. Remark 1 Long Cylinder Bed[S] S01 2 Rotary Hook Base Stud Bearing Collar :15mm dia Spiral Bevel Gear :.1 :28t Spiral Bevel Gear :.1 :14t Plain Washer :7.94*19*t Stopper Collar :7.94mm dia Shaft :Rotary Hook :7.94mm dia Needle Plate Bracket[S] S00 10 Spring Pin :3* Rotary Hook Support Rotary Hook : KHS12-RYPOEET Rotary Hook Set Screw :11/64* Bobbin :Regular Rotary Hook Bobbin Case :Regular Rotary Hook :Standard Lever Shaft :Knife[S] S00 17 E-Ring :4mm dia Thread Separating Plate :Direct Movement 2-Blade Type Movable Knife :Direct Movement 2-Blade Type Fixed Knife :Direct Movement 2-Blade Type Under Thread Presser Connecting Plate :Knife[S] S00 23 Lever Shaft :Knife Connecting Plate[S] S21 24 Lever :Knife Connecting Plate Shaft Base :Solenoid[A] A02 26 Rubber Packing Cord Clamp Stepped Screw :.1 :M2.5* Connecting Plate :Picker E-Ring :2mm dia Picker[S] S12 32 Holder :Picker Stopper :Picker Plate Spring :Rotary Hook Cover :t Straight Pin :.1 :3mm dia Rotary Hook Cover[S] S00 37 Cover :Needle Plate Bracket Needle Plate @ Hexagon Socket Head Countersunk Screw : M4*8 S SD 40 Cover :Cylinder Bed :Front Sensor Plate : Lever :ATH Card :Magnetic Sensor A 0J Base :Sensor Damper Ring :3mm dia. E Pulse Motor :42mm Square :Double-End 0J Base :ATH Motor Plastic Washer :6*15*t Connecting Plate :ATH Drive Arm Stepped Screw :.1 :M4* Cylinder bed (E1-03) ( 12 / 40 )

15 Color change system (E1-04) Symbol Upward compatibility TUMX-C TEJT2-C ( 13 / 40 )

16 Color change system (E1-04) Symbol. Part name Part. Remark 1 Base :Change Motor Collar :.1 :5.1mm dia Pulse Motor :42mm Square :Double-End[T] 0J T11 4 Knob :B B012 5 Roller Pin[S] S11 6 Cover :Change Sensor Arm 0C Base :Card 0C Card :TC Sensor :Magnetic Type 0J Mini Clamp :MB Bracket :Potentiometer 0C Stud :.4 :M Potentiometer Bearing Case :Change Cam Oil-Bushing :.2 :MB FDU Shaft :Change Cam Cam :Change Spacer :.2 :t ( 14 / 40 )

17 Arm 1 (E1-05-1) Symbol Upward compatibility TUMX-C TEJT2-C ( 15 / 40 )

18 Symbol. Part name Part. Remark 1 Head Tightening Collar :21mm dia Cam :Needle Bar[A] A03 4 Bearing Case :.2 :22mm dia.[s] S02 5 Cam :Needle Bar Needle Cage : KT404310NE01B Connecting Rod : Base :Take-Up Lever Cam Cam :Take-Up Lever :M6 :Regular Rotary Hook Washer :Cam Balancer :Head Spacer :Balancer Lever :Needle Bar[S] S00 14 Stepped Pin :.4[S] S00 15 Stepped Pin : Wick :3P* Stopper Collar :8mm dia Stepped Screw :.2 :M6*13[S] S11 19 Stepped Screw :.2 :M6* Wick :3.5*1* Screw With Pin :.3 :11/64-7.7[A] A11 22 Screw With Pin :.3 :11/ Wick :2.5*1* Connecting Rod : Needle Bar Reciprocator[A] 9A A00 26 Needle Bar Reciprocator[S] 9A S00 27 Torsion Spring :0.7mm dia Holder :Jump Spring Plain Washer :10.3*14*t Reciprocating Slide Block Plastic Bushing :.2 :7.24mm dia Damper Bracket :Needle Bar Reciprocator Screw With Pin :.3 :11/64-7.9[A] A22 34 Screw With Pin :.3 :11/ Flat Fillister Head Screw :9/64* Plain Washer :6*9.5*t @ Felt :14mm dia Needle Bar Drive Shaft :Automatic Lubrication[S] 0L S00 39 Needle Bar Drive Shaft :Automatic Lubrication 0L Wick :3.5P* Guide :Needle Bar Case[S] S22 42 Felt :Needle Bar Drive Shaft Arm 1 (E1-05-1) ( 16 / 40 )

19 Arm 2 (E1-05-2) Symbol Upward compatibility TUMX-C TEJT2-C ( 17 / 40 )

20 Symbol. Part name Part. Remark 1 Bearing Bushing :.1 :10mm dia Lever :Take-Up Lever[S] S00 3 Lever :Take-Up Lever Stepped Screw :.1 :M4* Roller :5*8* Plain Washer :4*7.5*t Straight Pin :.1 :10mm dia Arm :Take-Up Lever[S] S00 9 Lid :Take-Up Lever Shaft Holder :15.3mm dia Take-Up Lever Guide Linear Way :Needle Bar Case @ Reinforcing Plate @ Head Front Cover :L[A] LA00 14 Head Front Cover :L L Solenoid :Open Frame Lever :Solenoid Torsion Spring :0.5mm dia Collar :.1 :3.1mm dia Lever :Drive[S] S12 20 Head Front Cover :R R Guide Plate :Needle Bar Case Guide Bracket :Needle Bar Case Side Cover :Head :Upper Upper Thread Holder[A] 0B A01 25 Side Cover :Head :Lower Pulse Motor :42mm Square :Double-End[T] 0J T11 27 Base :Hook Motor 0B Collar :Spring Guide Torsion Spring :0.8mm dia Stepped Screw :.1 :9/64* Lever :Hook 0B Connecting Plate :Hook 0B Stepped Screw :.1 :M4* Spacer :Slide Hook 0B Slide :Hook 0B Washer :2.6*7*t Hook[S] 0B S11 38 Guide :Hook 0B Damper Ring :4mm dia Stepped Screw :.1 :9/64* Bracket :LED Lamp 0L Lamp :Needle Base LED Light[A] 0J A00 43 Clamp :LED Lamp :L 0L231003L Clamp :LED Lamp :R 0L231003R000 Arm 2 (E1-05-2) ( 18 / 40 )

21 Arm 3 (E1-05-3) Symbol Upward compatibility TUMX-C TEJT2-C ( 19 / 40 )

22 Symbol. Part name Part. Remark 1 Jump[A] A11 2 Bracket :Jump Motor Pulse Motor :42mm Square :Double-End[T] 0J T11 4 Torsion Spring :0.9mm dia Lever :Jump Washer :4.8*8*t0.8 S KC 7 Roller :4.7mm dia Stepped Screw :.1 :11/64* Torsion Spring :0.7mm dia Lever :Clutch :Middle Stepped Screw :.2 :M4* Damper Ring :4mm dia Screw With Pin :.1 :9/ Lever :Clutch :Reversing Lever :Clutch :Drive[S] S00 16 Base :Clutch Duracon Spacer :C Stepped Screw :.1 :9/64* Presser Foot Motor[A] 0J A00 20 Pulse Motor :42mm Square 44L :With Sensor[A] 0J A02 21 Base :Presser Foot Motor Stud :.1 :M Lever :Presser Foot[S] S01 24 Lever :Presser Foot Screw With Pin :.3 :M4-5.5[A] A00 26 Screw With Pin :.3 :M Wick :2.5*1* Connecting Rod :Presser Foot Stepped Screw :.2 :M4*12.5[A] A00 30 Presser Foot Reciprocator Shaft :Presser Foot Drive Shaft Holder :Presser Foot Drive Felt :Presser Foot Shaft Felt Presser :Presser Foot Shaft Stud :.1 :M Wick :3P* Arm 3 (E1-05-3) ( 20 / 40 )

23 Needle bar case 1 (E1-06-1) Symbol Upward compatibility TUMX-C TEJT2-C ( 21 / 40 )

24 Needle bar case 1 (E1-06-1) Symbol. Part name Part. Remark 1 Needle Bar Case @001 2 Screw :Needle Bar Needle Bar Compression Spring :0.6mm dia Felt Packing Damper Ring :F Stopper :Upper Dead Point Flat Fillister Head Screw :9/64*12 SA UN 9 Compression Spring :0.5mm dia Needle Bar Connecting Stud Screw With Pin :.1 :9/ Felt :Needle Bar Needle Clamp[S] S67 14 Slotted Head Set Screw :11/64*6B Needle :DB-K5Z1 # Needle Bar Guide @@ Presser Foot Connecting Stud Compression Spring :0.4mm dia Presser Foot Shaft Felt :Presser Foot O-Ring :SO Presser Foot :2mm dia./3mm dia @ Rail :Case :Lower @ Parallel Pin :4*16-h Split Collar :.1 :8mm dia Split Collar :.1 :8mm dia For 15-needle machine 26 Split Collar :.2 :8mm dia Split Collar :.2 :8mm dia For 15-needle machine 27 Guide Shaft :Take Up Lever @ Take-Up Lever[A] A44 29 Take-Up Lever[S] S44 30 Thread Guide Collar :2mm dia Boss :Take-Up Lever Lever :Stopper Torsion Spring :1mm dia Spring Hook Bar @ Stopper :Linear Way Flat Fillister Head Screw :M4* ( 22 / 40 )

25 Needle bar case 2A [6-needle M/C] (E1-06-2a) Symbol Upward compatibility TUMX-C TEJT2-C ( 23 / 40 )

26 Needle bar case 2A [6-needle M/C] (E1-06-2a) Symbol. Part name Part. Remark 1 Top Cover[A] @A00 2 Top Cover @003 3 Middle Thread Guide Base @000 4 Side Cover :L L000 4 Side Cover :L :15-Needle L000 5 Side Cover :R R000 5 Side Cover :R :15-Needle R000 6 Straight Pin :.1 :3mm dia Front Face Cover :Middle Thread Guide Base :Middle Thread Guide :0.4mm dia.[a] A11 8 Base :Middle Thread Guide :0.5mm dia.[a] A11 9 Base :Middle Thread Guide Spring Shaft :Thread Take-Up Spring Thread Take-Up Spring :.2 :0.4mm dia Thread Take-Up Spring :.2 :0.5mm dia Grommet :Middle Thread Guide Base Urethane Tube :4mm dia. :10L Face Cover :Needle Bar Case @ Stepped Screw :.1 :M3* Upper Thread Lock[A] @A12 17 Base :Upper Thread Lock @00A 18 Lock Shaft[S] S14 19 Compression Spring :0.3mm dia E-Ring :1.5mm dia Upper Thread Holder[A] 0B020037@A00 22 Base :Upper Thread Holder[S] 0B020039@S00 23 Base :Upper Thread Holder 0B020039@ Velcro 0B020038@ Upper Thread Holder[S] 0B020037@S00 26 Upper Thread Holder 0B020037@ Thread Suspender Disk 0B Compression Spring :0.3mm dia Presser :Thread Suspender Spring 0B Stepped Screw :.1 :9/64* Base :Change Roller[A] @A00 32 Base :Change Roller[S] @S00 33 Stepped Screw :.1 :M4* Roller :5*8* Plain Washer :4*7.5*t Wire diameter 0.5mm (For thick thread) Wire diameter 0.5mm (For thick thread) ( 24 / 40 )

27 Needle bar case 2B [12, 15-needle M/C] (E1-06-2b) Symbol Upward compatibility TUMX-C TEJT2-C ( 25 / 40 )

28 Needle bar case 2B [12, 15-needle M/C] (E1-06-2b) Symbol. Part name Part. Remark 1 Top Cover[A] @A00 2 Top Cover @000 3 Side Cover :L L000 3 Side Cover :L :15-Needle L000 4 Side Cover :R R000 4 Side Cover :R :15-Needle R000 5 Straight Pin :2mm dia @000 6 Base :Middle Thread Guide :0.4mm dia.[a] A00 6 Base :Middle Thread Guide :0.5mm dia.[a] A00 7 Base :Middle Thread Guide Side Wall Plate :Middle Thread Guide Spring Shaft :Thread Take-Up Spring Plain Washer :8*10*t Thread Take-Up Spring :.2 :0.4mm dia Thread Take-Up Spring :.2 :0.5mm dia Large Thread Holder Truss Head Tapping Screw :3P*12 S SD 14 Face Cover :Needle Bar Case @ Stepped Screw :.1 :M3* Upper Thread Lock[A] @A12 17 Base :Upper Thread Lock @00A 18 Lock Shaft[S] S14 19 Compression Spring :0.3mm dia E-Ring :1.5mm dia Upper Thread Holder[A] 0B020037@A00 22 Base :Upper Thread Holder[S] 0B020039@S00 23 Base :Upper Thread Holder 0B020039@ Velcro 0B020038@ Upper Thread Holder[S] 0B020037@S00 26 Upper Thread Holder 0B020037@ Thread Suspender Disk 0B Compression Spring :0.3mm dia Presser :Thread Suspender Spring 0B Stepped Screw :.1 :9/64* Base :Change Roller[A] @A00 32 Base :Change Roller[S] @S00 33 Stepped Screw :.1 :M4* Roller :5*8* Plain Washer :4*7.5*t Wire diameter 0.5mm (For thick thread) Wire diameter 0.5mm (For thick thread) ( 26 / 40 )

29 6-2. TMBP-SC Arm 1 (E2-05-1) Symbol Upward compatibility TUMX-C TEJT2-C ( 27 / 40 )

30 Symbol. Part name Part. Remark 1 Head Linear Way :Needle Bar Case @003 Arm 1 (E2-05-1) 3 Reinforcing Plate @002 For 12, 15-needle machine 4 Head Front Cover :L L014 5 Head Front Cover :R R001 6 Solenoid :Open Frame Lever :Solenoid Torsion Spring :0.5mm dia Collar :.1 :3.1mm dia Lever :Drive[S] S12 11 Guide Plate :Needle Bar Case Guide Bracket :Needle Bar Case Side Cover :Head :Lower Side Cover :Head :Upper Bracket :Jump Motor Pulse Motor :42mm Square :Double-End[T] 0J T11 17 Damper Ring :4mm dia Torsion Spring :0.9mm dia Lever :Jump Washer :4.8*8*t0.8 S KC 21 Roller :4.7mm dia Stepped Screw :.1 :11/64* Take-Up Lever Guide Rail ( 28 / 40 )

31 Arm 2 (E2-05-2) Symbol Upward compatibility TUMX-C TEJT2-C ( 29 / 40 )

32 Symbol. Part name Part. Remark 1 Needle Bar Reciprocator :GN[A] A67 2 Torsion Spring :0.7mm dia Holder :Jump Spring Needle Bar Reciprocator[S] S49 5 Plain Washer :10.3*14*t Reciprocating Slide Block Plastic Bushing :.2 :7.24mm dia Damper Bracket :Needle Bar Reciprocator Screw With Pin :.3 :11/64-7.9[A] A11 10 Screw With Pin :.3 :11/ Wick :2.5*1* Plain Washer :6*9.5*t @ Flat Fillister Head Screw :9/64* Felt :14mm dia mm-thick 15 Felt :14mm dia mm-thick 16 Presser Foot Reciprocator :47mm st[a] A24 17 Presser Foot Reciprocator :47mm st[s] S13 18 Damper Bracket :Presser Foot Reciprocator[S] S23 19 Needle Bar Drive Shaft :Automatic Lubrication[S] 0L S00 20 Needle Bar Drive Shaft :Automatic Lubrication 0L Wick :3.5P* Guide :Needle Bar Case[S] S11 23 Felt :Needle Bar Drive Shaft :D Straight Pin :.1 :8mm dia Lever :Take-Up Lever Stepped Screw :.1 :M4* Roller :4.7*7.94* Plain Washer :4*7.5*t Arm :Take-Up Lever Screw With Pin :.4 :M Roller :3mm dia Lid :Take-Up Lever Shaft Holder : 15.3mm dia Bearing Bushing :.1 :8mm dia Arm 2 (E2-05-2) ( 30 / 40 )

33 Arm 3 (E2-05-3) Symbol Upward compatibility TUMX-C TEJT2-C ( 31 / 40 )

34 Symbol. Part name Part. Remark 1 Tightening Collar :21mm dia Bearing Case :.2 :22mm dia.[s] S02 3 Bearing :60/22ZZ Cam :Needle Bar Needle Cage : KT404310NE01B Connecting Rod : Base :Take-Up Lever Cam Cam :Take-Up Lever :Regular Rotary Hook Washer :Cam Collar :.1 :21mm dia Cam :Presser Foot[A] A27 12 Stepped Pin :.4[S] S01 13 Stepped Pin : Wick :3P* Lever :Needle Bar[S] S12 16 Stepped Screw :.2 :M6*13[S] S11 17 Stepped Screw :.2 :M6* Wick :3.5*1* Connecting Rod Screw With Pin :.3 :11/64-7.7[A] A11 21 Screw With Pin :.3 :11/ Wick :2.5*1* Stopper Collar :8mm dia Stopper Collar :8mm dia Connecting Rod : Lever :Drive :Presser Foot :47 U8K Lever :Presser Foot[S] S58 28 Stepped Screw :.1 :M4* Roller :5*8* Plain Washer :4*7.5*t Screw With Roller Pin :.4 :11/64E[S] S00 32 Screw With Roller Pin :.4 :11/64E Stepped Pin :.4[S] S01 34 Stepped Pin : Plain Washer :8*15*t Arm 3 (E2-05-3) ( 32 / 40 )

35 Needle bar case 1 (E2-06-1) Symbol Upward compatibility TUMX-C TEJT2-C ( 33 / 40 )

36 Needle bar case 1 (E2-06-1) Symbol. Part name Part. Remark 1 Needle Bar Case @035 2 Needle Bar Compression Spring :0.5mm dia Felt Packing Damper Ring :F Stopper :Upper Dead Point Flat Fillister Head Screw :9/64*12 SA UN 8 Needle Bar Connecting Stud Compression Spring :0.9mm dia Presser Foot Connecting Stud Presser Foot[A] A00 2mm dia. hole (Standard) 11 Presser Foot[A] A05 3mm dia. hole (For thick thread) 12 Presser Foot mm dia. hole (Standard) 12 Presser Foot mm dia. hole (For thick thread) 13 Split Collar :Presser Foot Flat Fillister Head Screw :1/8* Damper Ring :A Needle Clamp[S] S67 17 Slotted Head Set Screw :11/64*6B Needle :DB-K5Z1 # Split Collar :.2 :8mm dia Split Collar :.2 :8mm dia For 15-needle machine 20 Guide Shaft :Take Up Lever @ Take-Up Lever[A] A33 22 Take-Up Lever[S] S33 23 Thread Guide Collar :2mm dia Boss :Take-Up Lever Split Collar :.1 :8mm dia Split Collar :.1 :8mm dia For 15-needle machine 26 Needle Bar Guide @@ Rail Guide @ Rail :Case :Lower @ Parallel Pin :4*16-h Spring Hook Bar @ Lever :Stopper Torsion Spring :1mm dia Stopper :Linear Way Flat Fillister Head Screw :M4* ( 34 / 40 )

37 Needle bar case 2A [6-needle M/C] (E2-06-2a) Symbol Upward compatibility TUMX-C TEJT2-C ( 35 / 40 )

38 Needle bar case 2A [6-needle M/C] (E2-06-2a) Symbol. Part name Part. Remark 1 Top Cover[A] @A00 2 Top Cover @003 3 Middle Thread Guide Base @000 4 Side Cover :L L000 4 Side Cover :L :15-Needle L000 5 Side Cover :R R000 5 Side Cover :R :15-Needle R000 6 Straight Pin :.1 :3mm dia Front Face Cover :Middle Thread Guide Base :Middle Thread Guide :0.4mm dia.[a] A11 8 Base :Middle Thread Guide :0.5mm dia.[a] A11 9 Base :Middle Thread Guide Spring Shaft :Thread Take-Up Spring Thread Take-Up Spring :.2 :0.4mm dia Thread Take-Up Spring :.2 :0.5mm dia Grommet :Middle Thread Guide Base Urethane Tube :4mm dia. :10L Pan Head Screw :9/64* Face Cover :Needle Bar Case @ Stepped Screw :.1 :9/64* Upper Thread Lock[A] @A12 18 Base :Upper Thread Lock @00A 19 Lock Shaft[S] S14 20 Compression Spring :0.3mm dia E-Ring :1.5mm dia Upper Thread Holder[A] 0B020036@A00 23 Bracket :Upper Thread Holder 0B Thread Suspender Disk 0B Compression Spring :0.3mm dia Presser :Thread Suspender Spring 0B Stepped Screw :.1 :9/64* Base :Upper Thread Holder[S] 0B020034@S00 29 Base :Upper Thread Holder 0B020034@ Velcro 0B020035@ Upper Thread Holder[S] 0B020033@S00 32 Upper Thread Holder 0B020033@ Collar :.1 :3mm dia Base :Change Roller[A] @A00 35 Base :Change Roller[S] @S00 36 Stepped Screw :.1 :M4* Roller :5*8* Plain Washer :4*7.5*t Wire diameter 0.5mm (For thick thread) Wire diameter 0.5mm (For thick thread) ( 36 / 40 )

39 Needle bar case 2B [12, 15-needle M/C] (E2-06-2b) Symbol Upward compatibility TUMX-C TEJT2-C ( 37 / 40 )

40 Needle bar case 2B [12, 15-needle M/C] (E2-06-2b) Symbol. Part name Part. Remark 1 Top Cover[A] @A00 2 Top Cover @000 3 Side Cover :L L000 3 Side Cover :L :15-Needle L000 4 Side Cover :R R000 4 Side Cover :R :15-Needle R000 5 Straight Pin :2mm dia @000 6 Base :Middle Thread Guide :0.4mm dia.[a] A00 6 Base :Middle Thread Guide :0.5mm dia.[a] A00 7 Base :Middle Thread Guide Side Wall Plate :Middle Thread Guide Spring Shaft :Thread Take-Up Spring Plain Washer :8*10*t Thread Take-Up Spring :.2 :0.4mm dia Thread Take-Up Spring :.2 :0.5mm dia Large Thread Holder Truss Head Tapping Screw :3P*12 S SD 14 Pan Head Screw :9/64* Face Cover :Needle Bar Case @ Stepped Screw :.1 :9/64* Upper Thread Lock[A] @A12 18 Base :Upper Thread Lock @00A 19 Lock Shaft[S] S14 20 Compression Spring :0.3mm dia E-Ring :1.5mm dia Upper Thread Holder[A] 0B020036@A00 23 Bracket :Upper Thread Holder 0B Thread Suspender Disk 0B Compression Spring :0.3mm dia Presser :Thread Suspender Spring 0B Stepped Screw :.1 :9/64* Base :Upper Thread Holder[S] 0B020034@S00 29 Base :Upper Thread Holder 0B020034@ Velcro 0B020035@ Upper Thread Holder[S] 0B020033@S00 32 Upper Thread Holder 0B020033@ Collar :.1 :3mm dia Base :Change Roller[A] @A00 35 Base :Change Roller[S] @S00 36 Stepped Screw :.1 :M4* Roller :5*8* Plain Washer :4*7.5*t Wire diameter 0.5mm (For thick thread) Wire diameter 0.5mm (For thick thread) ( 38 / 40 )

41 Upper thread holder (E2-07) Symbol Upward compatibility TUMX-C TEJT2-C ( 39 / 40 )

42 Upper thread holder (E2-07) Symbol. Part name Part. Remark 1 Hook[S] 0B S11 2 Pulse Motor :42mm Square :Double-End[T] 0J T11 3 Base :Hook Motor 0B Collar :Spring Guide Damper Ring :4mm dia Torsion Spring :0.8mm dia Lever :Hook 0B Connecting Plate :Hook 0B Slide :Hook 0B Washer :2.6*7*t Guide :Hook 0B Stepped Screw :.1 :M4* Stepped Screw :.1 :9/64* Stepped Screw :.1 :9/64* Spacer :Slide Hook 0B Bracket :LED Lamp 0L Lamp :Needle Base LED Light[A] 0J A00 18 Clamp :LED Lamp :L 0L231003L Clamp :LED Lamp :R 0L231003R000 ( 40 / 40 )

PARTS LIST TFMX-IIC P-MJ04-E

PARTS LIST TFMX-IIC P-MJ04-E 2009.03 Table of Contents GENERAL VIEW FRAMING MJ-1 TABLE MJ-2 MAIN SHAFT DRIVE SYSTEM MJ-3 GEAR BOX MJ-4 CYLINDER BED 1 MJ-5-1 CYLINDER BED 2 MJ-5-2 COLOR CHANGE SYSTEM A