Automatism for overhead doors English AUTOMATISM FOR OVERHEAD DOORS ASSEMBL. Please read this instructions very carefully before assembly

Transcription

1 AUTOMATISM FOR OVERHEAD DOORS ASSEMBL Please read this instructions very carefully before assembly Rev. //0

2

3 The pulley block was designed for emergency use situations only,so avoid to use it continuously al force 0ºC limit switches wires poorly connected change limit switches wires damaged Pulley do not work rpm rpm rpm change the axis x0v AC + N (With neutral) <-50ºC; <+50ºC <-50ºC; <+50ºC Pág.

4 C) Product Description:.. Productsexplanation ) 50 /00 Aluminium groove Rubber tube Screw Seamless solid plug Seamless hollow plug PVC soft tube Air wave switch Spiral cable Fig. 7.. Installation. 5 5 Lift device (Pulley block) Capacitor Gear reducer Gear of limit device Output axes hole 7 Gear of fine limit device AC Motor Cover )cut the rubber tube into proper length as you need. )cut the aluminiun groove into proper length as you need. )put the seamless hollow plug and PVC soft tube into rubber tube. )put the seamless solid plug into rubber tube. 5)fix up the aluminium groove. )put the Rubber tube which is well assembled into aluminium groove. ) Acessories Imagem Nome Espec. Qtd. Mounting bracket Straight key x 00 Expand bolt M0 Socket cap screw M0 x 0 M x 5 Screw Coil spring washer Ø 0 7 Flat washer Ø 0 Flat washer Ø 7)Install the Air wave electrics switch. Pág. 0 )connect the PVC soft tube with switch. 9)connect spiral cable with controller. Pág. 5

5 OPTIONAL SAFETY DEVICES D) Assembly: F) Installation: Before the installation of automatism, the door must be completely placed and tuned springs.. Photocells installation: ) Appearance of a standard application: () Photocellshould beinstalled atthe twosides ofthe doorframe,00mm height fromthe ground. () Switch off the power, connect Beam receiver and Beam emitter with the controller. Switch on power, adjust carefully the location of Beam receiver and Beam transmitter, the beam ofreceiver and Emitter should aim at each other. The red-light in receiver is dim, while the beams collimate, then, the door operator could work normally. 5 () Fixed by screw to ensure that the photocell would not shift easily. Fig. KVM Control box Door Track Bracket Tube axle Fixer for torsion spring Torsion spring Bracket for torsion spring Wire step pulley Steel wire Fig..Installating Air Wave Switch.. Working principle: the pow er from the aircompressin soft tube tra n sportationto Air wave switch. ) Motor mounting: Air wave switch controller Let the spring came with the Point the plate to the motor Gnd Air wave switch Resisted least 5cm outside the poly Gnd Unresisted Fig Pág. 05 controller. Pág.

6 5. Set the closing limit Fig 5. Place the motor shaft and springs make the markings of the holes Remove the engine and make holes Fig 5.5 Step - Close the door completely, and confirm which is the one of close limit block according to the situation, then loosen the screw adjuster on close limit block 0mm in marking Step - Adjust the fine adjustor till the close limit block touch the microswitch and LED on control box turn off Step - Start the operator,inspect if the close limit points is in accoed with door closed totally.if not,readjust from step. 5 Replace the engine in place and attach the bracket to the wall Put the brake to coincide Fig 5. with the shaft and spring engine Step - Fasten the screw adjustor on close limit block Attention: If the motor work in the wrong way change the connetions L and L. 5. Set «open» limit swicth Do the same that you do to set the «closing» limit swicth 7 Tighten the screws from support the engine and the wall Pág. 0 Pág.

7 ) Fix the control box in the wall.erase the codes Press «LEARN» for seconds until the LED flash. After this, all the codes were eliminated 7.LED for learning.receiver.connector.learn-button 5. Ending-swicth set Fig.- Height from the floor 00mm Motor If the engine star work in the wrong way, you should change the connections like we show in the picture. AC0V Fig.- Motor L L Limitador I Set srew Control box Set srew Set Thin Limitador II Set Thin Control box Fig.- E) Control box: Fig.- Emergency button Switch ON / OFF Close button Open button Interrupter Control box Remote control Fig 5- Control box Pág. 07 Pág.

8 Control board wiring diagram. DIP Switches setup. 0VAC Control Box ON OFF 9 DIP: ON: Enable auto closing,delay time is adjustable when rotating Vr potentiometer OFF: Disable auto closing DIP: ON: Human mode, the button should be pressed continuously when closing door OFF: Automatic mode 7 LED-R LED-S LED-T Fase 5 LED: Learning LED: Power LED: Opening Limit LED: Closing Limit LED5: - Stop LED: Air wave LED7: Opening LED9: Closing LED0: Photocells U. Add remote control 0V VAC Supply Operating temperature range NOTE: The operating mode of the transmitter is step by step for each button Discription of main board AC 0V 50HZ W Max. Consumpation Accessories power supply PHOTOCELL Techincal data OPEN BUTTON CLOSE LIMIT Press ««LEARN» for second,the Led flash,press one button from transmitter,the LED flash times and the button is programmed VDC CLOSE BUTTON OPEN LIMIT LIMIT SWITCH Service door LIGHT MOTOR ACV 0.A max Operating mode Soft start & stop Frequency MHZ.Transformer.Button connector.0.a Fuse.A Fuse 5.LED.Push button connector 7.DIP switch.receiver module connector 9.Potentiomer Vr:Potentiometer for adjust opening force Vr:Potentiometer for adjust closing force Vr:Potentiometer for adjust auto closing time Vr:Potentiometer for adjust running time Pág. 0 Pág.

9 . 00VAC Control board. DIP Switches setup ON OFF DIP: ON: Enable auto closing,the delay time is adjustable when rotating Vr potentiometer OFF: Disable auto closing DIP: ON: Human mode, the button should be pressed continuously when closing door OFF: Automatic mode DIP: ON: Enable force detecting,in this situation,when the door meets obstacle, it will reverse.the force can be adjusted by Vr and Vr OFF: Disable force detecting.dip: ON:Enable soft start&stop OFF: Disable soft start&stop LED: Learning LED: Power LED: Opening limit LED: Opening LED7: Closing LED: Photocells Neutral Phase Phase Phase LIGHT Press ««LEARN» for second,the Led flash,press one button from transmitter,the LED flash times and the button is programmed Technical Data Supply NOTE: The operating mode of the transmitter is step by step for each button X0V + N W Accessories power supply ACV 0.A max Frequency Pág. 09 Discription of main board Max. Consumpation Operating temperature range PHOTOCELL CLOSE LIMIT OPEN BUTTON LIMIT SWITCH. Add remote control CLOSE BUTTON OPEN LIMIT Service door LED: Closing limit LED5: Air wave MHZ.Transformer.Button connector.a fuse.led 5.LED.Push button 7.DIP switch.receiver 9.Potentiomers Vr:Potentiometer for adjust running time Vr:Potentiometer for adjust pause time Pág. 0