Installation Instructions

Transcription

1 LEDlux Lustre SKU# Rated Voltage V~ 50Hz Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference. Warranty This fitting is covered by a 3 year warranty. The warranty is from date of purchase, not the date of installation. If the fitting is not installed by a licensed electrician it will void the warranty. Please retain proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries. The use of non-recommended dimmers may damage your LED light fitting and will void the warranty. Warranty will be void if there is any damage due to improper usage or modification to the fitting. Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void warranty. Installation requirements Must be installed by a licensed electrician. All wiring and installation of the light fitting must adhere to local and national wiring rules. eg. AS/NZS 3000:2007/Amendment 2:2012 Electrical installations. This is a Class I fitting and must be earthed during installation. Select a suitable location for installation; - This product is suitable for indoor use only. - The mounting point must support 2 times the weight of the fitting. - Ensure the fitting is not installed in direct line of an air vent/system and is not placed in any moist of damp areas. A mecahnical ON/OFF switch must be incorporated into the fixed wiring circuit before the dimmer in order to shift the colour temperature between 3000K, 4000K or 5000K. Electronic ON/OFF switch/push-button type dimmers, eg. Lucci LEDlux SKU# push-button dimmer or Clipsal 31E2PUDM push-button dimmer are not compatible with colour shifting fittings. Load sensing type dimmers, e.g. Lumex LT1D450LSWE, are not compatible with colour shifting fittings. This fitting is dimmable and has been tested with Lucci LEDlux SKU# dimmer, Clipsal 32E450TM and Clipsal 32E450UDM dimmers only. The use of a LED dimmer such as the Lucci LEDlux SKU# dimmer is highly recommended. NOTE: Some dimmers can switch the LED load OFF (no visible light) in the minimum dimming position, this is not desirable and will affect the colour shift, memory and rest function. When using the Lucci LEDlux SKU# dimmer, ensure to adjust the variable resistor so that the minimum dimming position DOES NOT switch the LED load OFF. NOTE: The use of non-recommended dimmers may damage your LED light fitting and will void the warranty. NOTE: Dimming may cause buzzing sounds or a slight flicker. There may be slight delays with the LED light start up or slight uneven light performance when more than one LED light fitting is linked together, switched ON or dimmed. This is not a product fault and as such is not covered under warranty. NOTE: Some dimmers have a minimum load of 20W. Ensure the dimmer position is on the maximum setting before turning on the LED light and adjust the dimmer down to your desired light level. Take care not to pull any electrical wires during unpacking as this may damage the connection. Lay out all the components on a smooth surface and make sure there are no components missing before assembling. If parts are missing, return the complete product to the place of purchase for inspection or replacement. Check whether the fitting has been damaged during transport. Do not operate/install any product which appears 1 P a g e v 1. 4

2 damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement. Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work. Installation directions 1. Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. (Figure A) 2. Remove the shade from the fitting by loosening the locking brackets on the back of the fitting. (Figure B) 3. Use the fitting as a template to mark the screw positions onto the ceiling. 4. Install the fitting onto the ceiling by using appropriately sized mounting screws and anchors. (Figure C) Ensure the mounting screws and anchors used are suitable for the mounting surface. 5. Remove the cover from the terminal block and connect the mains supply wire to the terminal block. (Figure D). Mains Supply Wire Earth Yellow/Green Neutral Blue or Black Live Brown or Red Fitting Wire Yellow/Green Blue Brown Ensure that the wires are secure and no bare wires are exposed. Install the cover back over the terminal block. NOTE: A loop terminal is provided on the terminal block. Please see the LOOP TERMINAL section for assistance with the wiring connection and a diagram. (Figure G) 6. Install the shade onto the fitting using the locking brackets at the back of the fitting, ensure it is secure. (Figure E). 7. After the installation, switch on the fitting to test all the lighting functions and enjoy your new lighting product. 2 P a g e v 1. 4

3 LOOP TERMINAL: The loop terminal is provided as a second live supply terminal. It is useful when a switch is included into the wiring as shown in the diagram below. (Figure G) WARNING: ALL WIRING CONNECTION AND DISCONNECTION MUST BE PERFORMED BY A LICENSED ELECTRICIAN. (FIGURE G) COLOUR SHIFTING FUNCTION: Colour temperature shifting function Select the colour temperature of the fitting by turning ON/OFF the switch in the fixing wire (switch not included). Turn ON and then turn OFF the switch within 1 second, the colour temperature of the fitting will be changing in the following cycle: 3000K 5000K 4000K 3000K. Please ensure the dimmer position is on the maximum setting before changing the colour temperature by switch. Colour temperature memory function Select your preferred colour temperature and then turn OFF. After 6 seconds turn on the fitting and it will memorize the last colour temperature status. Colour temperature reset function When installing several fittings on the one circuit and the colour temperatures are in disorder, turn OFF the fittings and wait between 2 to 5 seconds and then turn on the fittings again. The colour temperature will change back to the default setting of 3000K. 3 P a g e v 1. 4

4 HOW TO REPLACE THE LED DRIVER: 1. Ensure the power is off. (figure A) 2. Remove the shade from the fitting by loosening the locking brackets on the back of the fitting. (Figure B) 3. Unplug the input and output wire connectors from the old LED driver. (Figure C) 4. Remove the LED driver from the lamp base by loosening 2 screws on the side. (Figure C) 5. Install the new replacement LED driver by tightening the 2 screws and reconnect the input and output wire connectors together. (Figure E) 6. Install the shade back onto the fitting by tightening the locking brackets on the back of the fitting. (Figure F) 4 P a g e v 1. 4

5 Troubleshooting PROBLEM POSSIBLE CAUSE SUGGESTED SOLUTION Does not work. (New installation) Wiring loose or no power to the LED fitting. Check your circuit breaker/safety switch box and turn on power to your circuit. Contact the installing licensed electrician to check if the fitting has been installed correctly. Check your circuit breaker/safety switch box and Does not work. No power to the LED fitting. turn on power to your circuit. (Existing installation) Contact your nearest Beacon Lighting store. Non-recommended dimmer used. Check the dimmer used. Ensure the dimmer used is on the list of recommended dimmers in this manual. Flickers when Some dimmers have a variable dimming. loading adjustment function. eg. Lucci The variable resistor needs to be adjusted to suit (New installation) LEDlux SKU# dimmer. the LED fitting load to reduce the flickering. This may not have been adjusted during the installation of the dimmer. Flickers when dimming. (Existing installation) Dimmer position on low. Ensure the dimmer position is on the maximum setting before turning on the LED fitting and adjust the dimmer down to your desired light level. Buzzing sound. Non-recommended dimmer used. Check the dimmer used. Ensure the dimmer used is on the list of recommended dimmers in this manual. Uneven light start up Ensure the dimmer position is on the maximum Dimmer position on low when (for multiple units on setting before turning on the LED fitting and adjust switched on. one dimmer) the dimmer down to your desired light level. Cannot reset to default Check the dimmer used. Ensure the dimmer used is colour temperature Non-recommended dimmer is used. on the list of recommended dimmers in the 3000K (for single or e.g. a load sensing dimmer or specification section in this manual. multiple units) electronic ON/OFF switch/push-button Cannot colour shift with 2-in-1 dimmer used. A mechanical ON/OFF switch must be incorporated the ON/OFF switch (for into the fixed wiring circuit before the dimmer. single or multiple units) 5 P a g e v 1. 4

6 Safety tips Always ensure the power is OFF and the fitting has cooled down before performing any maintenance, cleaning or making any adjustment to the fitting. To avoid injury or damage to the fitting, ensure that power leads and screws are secure before connecting the power. Select a suitable location away from liquids and hazards. Ensure that the fitting does not come in contact with corrosive chemicals, etc. To clean, wipe with a damp clean cloth. Never soak the fitting with water. Handle the fitting and cover/shade with care to avoid breakage. Specifications SKU # Insulation Class Rated Voltage Rated Wattage LED Specs Recommended Dimmers Weight Dimensions Serviceable Parts Class I V~ 50Hz 18W SEOUL LEDs, dimmable 3000K lumens, 4000K lumens, 5000K 850 lumens Lucci LEDlux SKU# dimmer (Highly Recommended) Clipsal 32E450TM, Clipsal 32E450UDM, (Compatible) (Please refer to the Installation Requirements or Troubleshooting section in this manual for more information on the recommended dimmers, performance, operation and tips.) 0.7kg H:80mm Dia:335mm LED driver Model#: ES0163D-E039 V2 6 P a g e v 1. 4