Round Die Products. Check our website for the latest technical information.

Transcription

1 Round Die Products Check our website for the latest technical information. 1

2 BUSHINGS General Information Bushings... 2 & 3 STANDARD SHOULDER BUSHINGS Bronze Plated & Solid Steel... 4 Solid Bronze & Self-Lubricating... 5 Pressed Fit... 6 Bushings for Lifter Pin Metric... 6 Long & Extra Long Shoulder Bushings... 7 SHORT SHOULDER BUSHINGS Bronze Plated... 8 Solid Bronze... 9 Self-Lubricating METRIC BUSHINGS NAAMS & 12 Standard Shoulder Bushings Metric Long & Extra Long Shoulder Bushings Metric Short Shoulder Bushings Metric TECHNICAL INFORMATION Toe Clamp Selection Toe Clamp Placement Bore Sizes for Pins & Bushings GUIDE PINS, continued Guide Pins Tap Fit (Demountable) & 29 Guide Pins Shoulder Inch Metric Guide Pins Removable Stripper Guide Pins & Bushings & 35 STOCK LIFTERS 75 Stock Lifters Stock Lifters Rail Lifters Rail Lifters Mini Lifters Repair Parts Metric Lifter Pins Stop Blocks PAD RETAINERS Pad Retainers, Standard Inch Pad Retainers, Reverse Mount Inch Pad Retainers, Standard & Reverse Metric.. 46 Spool Type Pad Retainers Metric MISCELLANEOUS BUSHINGS Running Fit Bushings Hardened Running Fit Bushings Soft Guide Bar Bushings (Wiper Bushings) Precision Bearings GUIDE PINS General Information Pins Straight Guide Pins TN & ATN Straight Guide Pins TPB Straight Guide Pins TPC Straight Guide Pins NAAMS Straight Guide Pins Hollow Straight Guide Pins TN Metric Straight Guide Pins TPB Metric Short SC-GSC SCB-GSCB SHOULDER BUSHING STYLES Standard AC-GAC ACB-GACB Long LAC-GLAC Extra-Long XLAC-GXLAC All bronze plated shoulder bushings must be wring-fit in the die shoe. It is also recommended that Solid Bronze shoulder bushings be mounted similarly. Bronze plated bushings feature figure 8 oil grooves for maximum lubrication. For long wear, bronze plated bushings should be lubricated with a high temperature, high pressure lithium grease on a regular basis. Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of self-lubricating bushings. DO NOT USE GREASE. 2

3 Specials have become very important at Lamina. The table below will give a basic idea of our everyday manufacturing capabilities. If you have a need for special bushings, please send your requests for quotations. See page 22 for pin manufacturing capabilities. BUSHING MANUFACTURING CAPABILITIES Series Inch Min. Length Max. Length Series Metric Min. Length Max. Length We are not restricted to the above parameters. Every quote will be analyzed for manufacturing possibility. Straight & Shoulder Bronze Plated & Solid Steel Solid Bronze Self-Lubricating LAMINA DIE SET STANDARD GRIND (LDSS) Tapers.0005 Nominal Wring Fit Diameter Slight taper on wring fit diameter facilitates installation. (This feature is standard on all bronze plated and solid steel shoulder bushings unless otherwise noted.) Bushings are held in place with toe clamps and screws unless otherwise noted. In the following pages bronze plated and solid steel bushings which are listed as ground are LDSS ground. GUIDE BUSHINGS Class 1 & 2 bushing dimensions shown opposite are for use in precision die sets. Class 3 bushings are for use with automotive, hardware, forming or draw dies where stamping stock is thicker than 1/16, and clearances between punch and die sections will be more than.003 per side. Bronze-Plated Bushings Available in Class 1 or Class 2 Solid Bronze Bushings Available in Class 1 or Class 2 Hardened Steel Bushings available in Class 2 Self-Lubricating Bushings available in Class 3 NOMINAL PIN DIAMETER 3/4 7/ /4 1-1/2 1-3/ /2 3 LAMINA BUSHINGS I.D. Dimensions Class 1 Class 2 Class /4 4-1/

4 Bushings Inch Wring Fit Style D4.187 C L BRONZE PLATED SOLID STEEL Grease Fitting (incl.) *See page 3 for details. See pages 16 & 17 for toe clamp installation instructions..75 L4.188 D5 D-Clamps & Screws are included with wring fi t style bushings. Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/ /8-27 NPTF, 7/16 hex STANDARD SHOULDER BUSHINGS BRONZE PLATED D4 D5 L4 Class 2* Class 1* Nom Pin Wring Fit Diameter Head Shoulder Head OD Overall Wring Fit Head GROUND UNGROUND GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GAC-750-S AC-750-S GAC-7501-S AC-7501-S 3/ GAC-875-S AC-875-S GAC-8751-S AC-8751-S 7/ GAC-100-S AC-100-S GAC-1001-S AC-1001-S GAC-100-L AC-100-L GAC-1001-L AC-1001-L GAC-125-S AC-125-S GAC-1251-S AC-1251-S / GAC-125-L AC-125-L GAC-1251-L AC-1251-L GAC-150-SP GAC-150-S AC-150-S GAC-1501-S AC-1501-S 1-1/ GAC-150-L AC-150-L GAC-1501-L AC-1501-L GAC-175-SP GAC-175-S AC-175-S GAC-1751-S AC-1751-S 1-3/ GAC-175-L AC-175-L GAC-1751-L AC-1751-L GAC-200-SP GAC-200-S AC-200-S GAC-2001-S AC-2001-S GAC-200-L AC-200-L GAC-2001-L AC-2001-L GAC-250-S AC-250-S GAC-2501-S AC-2501-S 2-1/ GAC-300-S AC-300-S GAC-3001-S AC-3001-S STANDARD SHOULDER BUSHINGS SOLID STEEL D4 D5 L4 Class 2 only* Nom Pin Wring Fit Diameter Head Shoulder Head OD Overall Wring Fit Head GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GAC-750-SS AC-750-SS 3/ GAC-100-SS AC-100-SS GAC-100-SS2 AC-100-SS GAC-125-SS AC-125-SS / GAC-125-SS2 AC-125-SS GAC-150-SS AC-150-SS / GAC-150-SS2 AC-150-SS GAC-175-SS AC-175-SS / GAC-175-SS2 AC-175-SS GAC-200-SS AC-200-SS GAC-200-SS2 AC-200-SS GAC-250-SS AC-250-SS 2-1/

5 Bushings Inch Wring Fit Style D L4.188 SOLID BRONZE SELF-LUBRICATING *See page 3 for details. See pages 16 & 17 for toe clamp installation instructions. Grease Fitting (Solid Bronze only) Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex D5 D-Clamps & Screws are included with wring fi t style bushings. STANDARD SHOULDER BUSHINGS SOLID BRONZE D4 D5 L4 Nom Head Wring Class 2* Class 1* Wring Fit Diameter Head Shoulder Overall Head Pin OD Fit GROUND UNGROUND GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GAC-750-SB AC-750-SB GAC-7501-SB AC-7501-SB 3/ GAC-875-SB AC-875-SB GAC-8751-SB AC-8751-SB 7/ GAC-100-SB AC-100-SB GAC-1001-SB AC-1001-SB GAC-125-SB AC-125-SB GAC-1251-SB AC-1251-SB 1-1/ GAC-150-SB AC-150-SB GAC-1501-SB AC-1501-SB 1-1/ GAC-175-SB AC-175-SB GAC-1751-SB AC-1751-SB 1-3/ GAC-200-SB AC-200-SB GAC-2001-SB AC-2001-SB GAC-250-SB AC-250-SB GAC-2501-SB AC-2501-SB 2-1/ GAC-300-SB AC-300-SB GAC-3001-SB AC-3001-SB STANDARD SHOULDER BUSHINGS SELF-LUBRICATING D4 D5 L4 Nom. Head Wring Class 3 only* Wring Fit Diameter Head Shoulder Overall Head Pin OD Fit GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GACB-750-S ACB-750-S 3/ GACB-100-S ACB-100-S GACB-125-S ACB-125-S 1-1/ GACB-150-S ACB-150-S 1-1/ GACB-175-S ACB-175-S 1-3/ GACB-200-S ACB-200-S GACB-250-S ACB-250-S 2-1/ GACB-300-S ACB-300-S Note: Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of self-lubricating bushings. DO NOT USE GREASE. All Standard Shoulder Bushings (unless otherwise noted) are to be wring fi t and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see bore size information on page 18. 5

6 Bushings Inch Pressed Fit Style Press Fit Shoulder Bushings allow for fast, easy installation. Eliminates the use of clamps and screws. Grease Fittings 3/4-1/4-28 NTF, 5/16 hex 7/8-1/8-27 NPTF, 7/16 hex.750 L4 Figure 8 oil grooves allow the lubricant to fl ow smoothly throughout the bushing I.D. *Please note! BRONZE PLATED Grease Fitting SHOULDER BUSHING PRESS FIT L4 REC'D NOM. PIN * PRESS FIT HEAD OVERALL HEAD PRESS FIT BORE DIAMETER DIAMETER O.D. SIZE / / Press Fit bushings have tapered holes, larger at press fit end. This facilitates honing, since the bore will close up in a more nearly straight line when pressed in. While these bushings are precision fi nished on the O.D. a small amount of stock is left on the I.D. to allow for honing because they are pressed fi t type. Toe clamps and screws are not provided with press fi t shoulder bushings and they do not come with an LDSS grind. BUSHINGS FOR LIFTER PINS METRIC MBL MBL MBL

7 Bushings Wring Fit Style D D-Clamps & Screws are included with wring fi t style bushings. L4.75 BRONZE PLATED SOLID STEEL *See page 3 for details. See pages 16 & 17 for toe clamp placement instructions. Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex D5 Grease Fitting LONG SHOULDER BUSHINGS BRONZE PLATED D4 D5 L4 Nom Class 2* Class 1* Wring Fit Diameter Head Shoulder OD Overall Wring Head Pin Fit Head GROUND UNGROUND GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GLAC-750-S LAC-750-S GLAC-7501-S LAC-7501-S 3/ GLAC-875-S LAC-875-S GLAC-8751-S LAC-8751-S 7/ GLAC-100-S LAC-100-S GLAC-1001-S LAC-1001-S GLAC-125-S LAC-125-S GLAC-1251-S LAC-1251-S 1-1/ GLAC-150-S LAC-150-S GLAC-1501-S LAC-1501-S 1-1/ GLAC-150-SP 1-1/ GLAC-175-S LAC-175-S GLAC-1751-S LAC-1751-S 1-3/ GLAC-200-S LAC-200-S GLAC-2001-S LAC-2001-S GLAC-250-S LAC-250-S GLAC-2501-S LAC-2501-S 2-1/ GLAC-300-S LAC-300-S GLAC-3001-S LAC-3001-S EXTRA LONG SHOULDER BUSHINGS BRONZE PLATED D4 D5 L4 Nom Class 2* Class 1* Wring Fit Diameter Head Shoulder OD Fit Head Wring Overall Pin Head GROUND UNGROUND GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GXLAC-750-S XLAC-750-S GXLAC-7501-S XLAC-7501-S 3/ GXLAC-875-S XLAC-875-S GXLAC-8751-S XLAC-8751-S 7/ GXLAC-100-S XLAC-100-S GXLAC-1001-S XLAC-1001-S GXLAC-125-S XLAC-125-S GXLAC-1251-S XLAC-1251-S 1-1/ GXLAC-150-S XLAC-150-S GXLAC-1501-S XLAC-1501-S 1-1/ LONG & EXTRA LONG SHOULDER BUSHINGS SOLID STEEL D4 D5 L4 Class 2 only* Nom Pin Wring Fit Diameter Head Shoulder Head OD Overall Wring Fit Head GROUND UNGROUND Diam. GROUND UNGROUND OD OD Groove Length Length Length GXLAC-750-SS XLAC-750-SS 3/ GXLAC-100-SS XLAC-100-SS GXLAC-125-SS XLAC-125-SS 1-1/ GXLAC-150-SS XLAC-150-SS 1-1/ GXLAC-175-SS XLAC-175-SS 1-3/ GLAC-200-SS LAC-200-SS GXLAC-200-SS XLAC-200-SS GLAC-250-SS LAC-250-SS 2-1/

8 Bushings Inch Wring Fit Style Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex BRONZE PLATED *See page 3 for details. See pages 16 & 17 for toe clamp placement instructions. D-Clamps & Screws are included with wring fi t style bushings. SHORT SHOULDER BUSHINGS BRONZE PLATED D4 L4 Nom Class 2* Class 1* Pin Wring Fit Diameter Head Shoulder Overall Wring Fit Head GROUND UNGROUND GROUND UNGROUND Diam. GROUND UNGROUND OD OD Length Length Length GSC-750-S SC-750-S GSC-7501-S SC-7501-S / GSC-750-L SC-750-L GSC-7501-L SC-7501-L GSC-875-S SC-875-S GSC-8751-S SC-8751-S / GSC-875-L SC-875-L GSC-8751-L SC-8751-L GSC-100-S SC-100-S GSC-1001-S SC-1001-S GSC-100-L SC-100-L GSC-1001-L SC-1001-L GSC-125-S SC-125-S GSC-1251-S SC-1251-S / GSC-125-L SC-125-L GSC-1251-L SC-1251-L GSC-150-S SC-150-S GSC-1501-S SC-1501-S / GSC-150-L SC-150-L GSC-1501-L SC-1501-L GSC-175-S SC-175-S GSC-1751-S SC-1751-S / GSC-175-L SC-175-L GSC-1751-L SC-1751-L GSC-200-S SC-200-S GSC-2001-S SC-2001-S GSC-200-L SC-200-L GSC-2001-L SC-2001-L GSC-250-S SC-250-S GSC-2501-S SC-2501-S GSC-250-M SC-250-M GSC-2501-M SC-2501-M 2-1/ GSC-250-L SC-250-L GSC-2501-L SC-2501-L GSC-300-S SC-300-S GSC-3001-S SC-3001-S GSC-300-M SC-300-M GSC-3001-M SC-3001-M GSC-300-L SC-300-L GSC-3001-L SC-3001-L Reference on page 9. For bushing I.D.s less than 1.25, hole diameter is.188; for bushing I.D.s 1.25+, hole diameter is.344. D4 L4 Lamina pins and bushings are used in die sets for the metal stamping industry. 8

9 Bushings Inch Wring Fit Style Grease Fittings Ø3/4-1/4-28 NTF, 5/16 hex Ø7/8-1/8-27 NPTF, 7/16 hex L4 SOLID BRONZE *See page 3 for details. D-Clamps & Screws are included D4 See pages 16 & 17 for toe clamp placement instructions. with wring fi t style bushings. SHORT SHOULDER BUSHINGS SOLID BRONZE D4 L4 Nom Class 2* Class 1* Wring Fit Diameter Head Shoulder Fit Overall Wring Pin Head GROUND UNGROUND GROUND UNGROUND Diam. GROUND UNGROUND OD OD Length Length Length GSC-750-SB SC-750-SB GSC-7501-SB SC-7501-SB 3/ GSC-750-LB SC-750-LB GSC-7501-LB SC-7501-LB GSC-875-SB SC-875-SB GSC-8751-SB SC-8751-SB 7/ GSC-875-LB SC-875-LB GSC-8751-LB SC-8751-LB GSC-100-SB SC-100-SB GSC-1001-SB SC-1001-SB GSC-100-LB SC-100-LB GSC-1001-LB SC-1001-LB GSC-125-SB SC-125-SB GSC-1251-SB SC-1251-SB / GSC-125-LB SC-125-LB GSC-1251-LB SC-1251-LB GSC-150-SB SC-150-SB GSC-1501-SB SC-1501-SB / GSC-150-LB SC-150-LB GSC-1501-LB SC-1501-LB GSC-175-SB SC-175-SB GSC-1751-SB SC-1751-SB / GSC-175-LB SC-175-LB GSC-1751-LB SC-1751-LB GSC-200-SB SC-200-SB GSC-2001-SB SC-2001-SB GSC-200-LB SC-200-LB GSC-2001-LB SC-2001-LB GSC-250-SB SC-250-SB GSC-2501-SB SC-2501-SB GSC-250-MB SC-250-MB GSC-2501-MB SC-2501-MB 2-1/ GSC-250-LB SC-250-LB GSC-2501-LB SC-2501-LB GSC-300-SB SC-300-SB GSC-3001-SB SC-3001-SB GSC-300-MB SC-300-MB GSC-3001-MB SC-3001-MB GSC-300-LB SC-300-LB GSC-3001-LB SC-3001-LB GSC-375-B SC-375-B 3-3/ GSC-450-B SC-450-B 4-1/ Bushings of 2.50 diameter and larger have 1.25 dimensions. For bushing I.D.s less than 1.25, hole diameter is.188; for bushing I.D.s 1.25+, hole diameter is.344. All Short Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see bore size information on page 18. 9

10 Bushings Inch Wring Fit Style.187 BRONZE with SELF-LUBRICAT- ING GRAPHITE PLUGS *See page 3 for details. See pages 16 & 17 for toe clamp placement instructions. D-Clamps & Screws are included with wring fi t style bushings. SHORT SHOULDER BUSHINGS SELF-LUBRICATING D4 L4 Class 3 only* Nom Pin Wring Fit Diameter Head Shoulder Overall Wring Fit Head GROUND UNGROUND Diam. GROUND UNGROUND OD OD Length Length Length GSCB-750-S SCB-750-S / GSCB-750-L SCB-750-L GSCB-875-S SCB-875-S / GSCB-875-L SCB-875-L GSCB-100-S SCB-100-S GSCB-100-L SCB-100-L GSCB-125-S SCB-125-S / GSCB-125-L SCB-125-L GSCB-150-S SCB-150-S / GSCB-150-L SCB-150-L GSCB-175-S SCB-175-S / GSCB-175-L SCB-175-L GSCB-200-S SCB-200-S GSCB-200-L SCB-200-L GSCB-250-S SCB-250-S GSCB-250-M SCB-250-M 2-1/ GSCB-250-L SCB-250-L GSCB-300-X SCB-300-X GSCB-300-S SCB-300-S GSCB-300-M SCB-300-M GSCB-300-L SCB-300-L GSCB-375-S SCB-375-S 3-3/ GSCB-450-S SCB-450-S 4-1/ Self-lubricating bronze with graphite bushings require initial lubrication with light oil. Periodic lubrication will extend the life of self-lubricating bushings. Do not use grease. D4 L4 10

11 Bushings Metric Wring Fit Style G720000C Clamps & Screws are included with NAAMS wring fi t style bushings. 6 BRONZE with SELF-LUBRICATING GRAPHITE PLUGS See page 17 for toe clamp placement instructions. D4 SHORT SHOULDER BUSHINGS SELF-LUBRICATING NAAMS # TOE NOM. PIN TOL WRING FIT TOL D4 OVERALL WRING FIT CLAMPS & DIAMETER H6 DIAMETER G6 SCREWS G G G G G G G G G NOTE: Evenly distributed graphite covers 20-30% of the sliding surface. Graphite is positioned to ensure overlapping in the slide direction. See page 17 for Toe Clamp information and page 18 for bore sizes These short shoulder bushings are made especially for automotive stamping companies. They conform to the standards agreed to by the North American Automotive Metric Standards group. AUTOMOTIVE METRIC NAAMS STANDARD 3 11

12 Bushings Metric These pad bushings are made especially for automotive stamping companies. They conform to the standards agreed to by the North American Automotive Metric Standards group. BRONZE with SELF LUBRICATING GRAPHITE PLUGS See page 17 for toe clamp installation instructions. SELF-LUBRICATING PAD BUSHINGS NAAMS NOM. PIN TOL WRING FIT TOL D4 OVERALL DIAMETER C9 DIAMETER G6 G G G G G G G G NOTE: Evenly distributed graphite covers 20-30% of the sliding surface. Graphite is positioned to ensure overlapping in the slide direction. AUTOMOTIVE METRIC NAAMS STANDARD See page 18 for bore size information. D4 6 A full complement of flat products is also available from the Lamina Components line. 12

13 Bushings Metric Wring Fit Style Bronze plated shoulder bushings are available in metric sizes. D4 5 5 BRONZE PLATED See pages 16 & 17 for toe clamp installation instructions. D-Clamps & Screws are included with wring fi t style bushings. Grease Fitting Grease Fittings, North America Ø18 & 19mm - 1/4-28 NTF, 5/16 hex Ø24-80mm - 1/8-27 NPTF, 7/16 hex STANDARD SHOULDER BUSHINGS BRONZE PLATED METRIC D4 D5 L4 # NOM. WRING FIT HEAD SHOULDER HEAD OVERALL WRING FIT HEAD CLAMPS PIN DIAMETER O.D. O.D. O.D. & DIA GROUND UNGROUND GROUND UNGROUND GROOVE SCREWS GAC-18S AC-18S GAC19S AC19S GAC24S AC24S GAC25S AC25S GAC30S AC30S GAC32S AC32S GAC40S AC40S GAC42S AC42S GAC50S AC50S GAC52S AC52S GAC63S AC63S GAC80S AC80S *Unground wring fi t tolerance is All Standard Shoulder Bushings (unless otherwise noted) are to be wring fi t and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see clamping information on pages 16 & 17 and bore size information on page D5 L4 13

14 Bushings Metric Wring Fit Style D D-Clamps & Screws are included with wring fi t style bushings. L4 D5 Grease Fitting Grease Fittings, North America Ø18 & 19mm - 1/4-28 NTF, 5/16 hex Ø24-80mm - 1/8-27 NPTF, 7/16 hex See pages 16 & 17 for toe clamp placement instructions. LONG & EXTRA LONG SHOULDER BUSHINGS BRONZE PLATED METRIC NOM. PIN DIA. WRING FIT O.D. GROUND UNGROUND GROUND UNGROUND GLAM-18F LAM-18F GLAC-18S LAC-18S GLAM-19F LAM-19F GLAC-19S LAC-19S GLAM-24F LAM-24F GLAC-24S LAC-24S GLAM-25F LAM-25F GLAC-25S LAC-25S GLAM-30F LAM-30F GLAC-30S LAC-30S GLAM-32F LAM-32F GLAC-32S LAC-32S GLAM-40F LAM-40F GLAC-40S LAC-40S GLAM-42F LAM-42F GLAC-42S LAC-42S GLAM-50F LAM-50F GLAC-50S LAC-50S GLAM-52F LAM-52F GLAC-52S LAC-52S GLAM-63F LAM-63F GLAC-63S LAC-63S GLAM-80F LAM-80F GLAC-80S LAC-80S *Unground wring fi t tolerance is HEAD O.D. D4 SHOULDER O.D / D5 HEAD O.D. GROOVE OVERALL / WRING FIT / L4 HEAD # CLAMPS & SCREWS All Standard Shoulder Bushings (unless otherwise noted) are to be wring fi t and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see clamping information on pages 16 & 17 and bore size information on page

15 Bushings Metric Wring Fit Style Grease Fittings, North America Ø18 & 19mm - 1/4-28 NTF, 5/16 hex Ø24-80mm - 1/8-27 NPTF, 7/16 hex * H1 See pages 16 & 17 for toe clamp placement instructions. SHORT SHOULDER BUSHINGS BRONZE PLATED METRIC NOM. PIN DIA. WRING FIT DIAMETER *Ø4.76 for bushings with nom. I.D.s between 18 & 32mm. *Ø8.73 for bushings with nom. I.D.s between 40 & 80mm. D-Clamps & Screws are included with wring fi t style bushings. GROUND UNGROUND GROUND UNGROUND GSC-18S SC-18S GSCL-18F SCL-18F GSC-19S SC-19S GSCL-19F SCL-19F GSC-24S SC-24S GSCL-24F SCL-24F GSC-25S SC-25S GSCL-25F SCL-25F GSC-30S SC-30S GSCL-30F SCL-30F GSC-32S SC-32S GSCL-32F SCL-32F GSC-40S SC-40S GSCL-40F SCL-40F GSC-42S SC-42S GSCL-42F SCL-42F GSC-50S SC-50S GSCL-50F SCL-50F GSC-52S SC-52S GSCL-52F SCL-52F GSC-63S SC-63S GSCL-63F SCL-63F GSC-80S SC-80S *Unground wring fi t tolerance is HEAD O.D. 13 D4 SHOULDER O.D / D4 OVERALL / WRING FIT / H1 LUBE HOLE CENTER # CLAMPS & SCREWS All Standard Shoulder Bushings (unless otherwise noted) are to be wring fit and held in place with toe clamps and screws. This means that the bushing should be installed into the die shoe using a wringing (circular) motion with the heel of the hand. Please see clamping information on pages 16 & 17 and bore size information on page

16 Toe Clamp Information for Inch & Metric Plain Bearing Die Bushings Bushing I.D. # Provided AC, LAC, XLAC CLAMP & SCREW PLACEMENT INCH Bolt Circle Diameter D-Clamps X-40 Clamps AC, LAC, SC LMB SC LMB XLAC Bushing I.D. AC, LAM, LAC, SC Toe Clamp Dimensions # Provided METRIC Bolt Circle Diameter D- Clamps X-40 Clamps D-Clamp & BHC Screw (5/16-18 x 3/4") D-Clamp & F Metric Screw (M8 x mm) X-40-Clamp & SHC Screw (5/16-18 x 3/4") X-40-Clamp & F Metric Screw (M8 x mm) 16 REPLACEMENT KITS CLAMPS & SCREWS D-CLAMPS INCH METRIC Nom. Pin Diameter # Clamps & Screws per Kit # Kits Needed Nom. Pin Diameter # Clamps & Screws per Kit # Kits Needed CSK /8 7/8 2 1 CSK CSK /4 3 1 CSK CSK /2 2 2 CSK CSK /2 3 2 X-40 CLAMPS INCH METRIC Nom. Pin Diameter # Clamps & Screws per Kit # Kits Needed Nom. Pin Diameter # Clamps & Screws per Kit # Kits Needed CSK /8 7/8 2 1 CSK CSK /4 3 1 CSK CSK /2 2 2 CSK CSK /2 3 2 Bolt Circle Diameter Drawing above can refer to either D-Clamps or X-40-Clamps

17 Toe Clamp Information for Inch & Metric Demountable Components NOM. PIN DIA. 1, 1 1 /4, & 1 1 /2 1 3 /4, 2, 2 1 /2 & /4, 2, 2 1 /2 & /4, 2, 2 1 /2 & 3 BALL-BEARING DEMOUNTABLE COMPONENT CLAMP ARRANGEMENTS STANDARD LEFT - RIGHT FEED FEED FEED FEED FRONT to BACK FEED (Center Post Die Sets) FEED FEED FEED FEED ROUND DIES BOLT CIRCLE DIAMETERS DEMOUNTABLE BALL BEARING BUSHINGS Nominal Bushing Bolt Circle Diameter Diameter / / / / DEMOUNTABLE BALL BEARING & PLAIN BEARING PINS Nominal Bushing Bolt Circle Diameter Diameter / / / / KEYLESS DEMOUNTABLE BALL BEARING BUSHINGS Nominal Bushing Bolt Circle Diameter Diameter / / / / KEYLESS DEMOUNTABLE BALL BEARING PINS Nominal Bushing Bolt Circle Diameter Diameter / / / / BUSHING CLAMPING PROCEDURES AUTOMOTIVE METRIC NAAMS STANDARD 6 Clamp Part No: G720000C M8 x 1.25 x 20 Long D4 (O.D. of Bushing Shoulder) B.C. = D (ID of Bushing) M8 x 1.25 Tap (3) Holes equally spaced D4 B.C. (D4 + 18) NOTES & SPECIFICATIONS: Bushings will be supplied with (3) toe clamps and (3) screws - M8. Screws must engage 16mm minimum deep into die shoe. 17

18 18 Nominal Pin Diameter Standard Inch GAC, GLAC, GXLAC & GSC Style Bushings DEFINITIONS OF MOUNTING PROCEDURES Pins and bushings require specific mounting procedures. By following these procedures the components should give maximum life and reduce downtime due to improper alignment, breakage and uneven wear. Pressed Fit The component is installed in an interference condition: the bore size is smaller than the pressed fi t portion of the component. RECOMMENDED BORE SIZES FOR PLAIN BEARING PINS & BUSHINGS Standard Metric GAC, GLAC, GLAM & GSC Style Bushings Short Shoulder & Pad Bushings NAAMS Bushing Liner for Removable Pin Straight Guide Pins Inch TN & ATN Straight Guide Pins Metric TN Straight Guide Pins Inch TPC Bushings that require a pressed fi t should never be frozen or hammered. They should be forced into place using a hydraulic press or other proper tooling. Improper methods can permanently change the tolerance of the component. Pins can be forced into place using a hydraulic press; or the pins can be frozen and pressed into place. Lamina does not recommend hammering pins into place. Hammering can cause the pins to mushroom or expand on the pin Straight Guide Pins Metric NAAMS Guide Pins with Shoulders Metric NAAMS D'mountable Inch Guide Pins Standard Metric Guide Pins WRING FIT WRING FIT WRING FIT PRESSED FIT PRESSED FIT PRESSED FIT PRESSED FIT PRESSED FIT TAP FIT TAP FIT TAP FIT 3/4 in /8 in in /4 in /2 in /4 in in /2 in in GSC ONLY in /4 in /2 in mm mm mm mm mm mm mm mm mm mm mm mm mm mm mm end resulting in permanent distortion of the component. Tap Fit The component should be tapped using a soft hammer into the bored hole and secured with toe clamps. Wring Fit The component should be installed using a wringing (circular) motion with the heel of the hand. Wring fit components are to be held in place with toe clamps, retaining rings or plates.

19 Bearings Pressed Fit Chamfer Figure 8 Oil Groove Sharp Corner (Both Ends) For Machine Tools, Fixtures, etc. Straight Design, Wiper type Lamina-Bronze on steel provides longer wearing running fits No reaming or honing after press fitting bearing HEAT TREATED L2 Bearings for Radial or Linear Applications I.D O.D BEARINGS RUNNING FIT HARDENED RECOM- MENDED BORE SIZE L I.D O.D *This diameter only. RECOM- MENDED BORE SIZE L 625-x-75-RFB x-175-RFB x-100-RFB x-200-RFB x-125-RFB x-250-RFB x-75-RFB x-300-RFB x-100-RFB x-350-RFB x-125-RFB x-200-RFB x-150-RFB x-250-RFB x-100-RFB x-300-RFB x-125-RFB x-350-RFB x-150-RFB x-400-RFB x-175-RFB x-250-RFB x-200-RFB x-300-RFB x-125-RFB x-350-RFB x-150-RFB x-400-RFB x-175-RFB x-450-RFB x-200-RFB x-500-RFB x-250-RFB x-300-RFB x-150-RFB x-350-RFB x-175-RFB x-400-RFB * x-200-RFB x-450-RFB x-250-RFB x-500-RFB x-300-RFB x-600-RFB

20 Bearings Pressed Fit NON-HEAT TREATED Chamfer Figure 8 Oil Groove Sharp Corner (Both Ends) L2 For Machine Tools, Fixtures, etc. Straight Design, Wiper type Lamina-Bronze on steel provides longer wearing running fits Flash-plated O.D. prevents scoring when pressing bearing in and out BEARINGS RUNNING FIT NON-HEAT-TREATED RECOM- RECOM- MENDED MENDED I.D. 0.D. L I.D. O.D. L BORE SIZE BORE SIZE SRFB-75-x SRFB-175-x SRFB-75-x SRFB-175-x SRFB-75-x SRFB-175-x SRFB-75-x SRFB-175-x SRFB-100-x SRFB-200-x SRFB-100-x SRFB-200-x SRFB-100-x SRFB-200-x SRFB-100-x SRFB-200-x SRFB-100-x SRFB-200-x SRFB-100-x SRFB-200-x SRFB-125-x SRFB-200-x SRFB-125-x SRFB-200-x SRFB-125-x SRFB-250-x SRFB-125-x SRFB-250-x SRFB-125-x SRFB-250-x SRFB-125-x SRFB-250-x SRFB-125-x SRFB-250-x SRFB-150-x SRFB-250-x SRFB-150-x SRFB-250-x SRFB-150-x SRFB-250-x SRFB-150-x SRFB-300-x SRFB-150-x SRFB-300-x SRFB-150-x SRFB-300-x SRFB-150-x SRFB-300-x * SRFB-175-x SRFB-300-x SRFB-175-x SRFB-300-x SRFB-175-x SRFB-300-x SRFB-175-x SRFB-300-x *This diameter only. 20 Bearings for Radial or Linear Applications

21 Guide Bar Bushings Wring Fit Style Used in Transfer Machinery Bronze Plated Steel for strength and lubricity Guide Bar Bushings are to be wring fit and held in place with toe clamps & screws. Please see clamping information on pages 16 & 17 and bore size information on page 18. GROUND UNGROUND GROUND UNGROUND GLMB-062 GLMB-075 GLMB-100 GLMB-125 GLMB-150 GLMB-175 GLMB-200 GLMB-250 GLMB-300 GLMB-375 GLMB-450 LMB-062 LMB-075 LMB-100 LMB-125 LMB-150 LMB-175 LMB-200 LMB-250 LMB-300 LMB-375 LMB-450 Bearings Pressed Fit GUIDE BAR BUSHINGS Bearings for Radial or Linear Applications Wiper Head D4 L4 L5 H Sharp Corner (Both Ends) # CLAMPS & SCREWS H D4 Recommended Bore Size STANDARD EXTRA-LONG L5 L Flat D-Clamps & Screws are included with wring fi t style bushings. PRECISION BEARINGS Nom. Pin L Diameter B / B /8 1-3/ B B / B / B / B B / B / B / B B /

22 General Information Guide Pins Below are listed standard diameters and minimum/maximum lengths that we are able to machine to your specifi cations. We can also manufacture in-between diameters. We are able to make specials to meet your exact specifi catons. Please call, fax or for a quotation form. Every quote will be answered! Outside Diameter MINIMUM & MAXIMUM PIN S INCH METRIC Minimum Length Maximum Length Outside Diameter Minimum Length Maximum Length & & & & & TN, ATN, TPB & TPC STRAIGHT PINS Lamina TPB & TPC Pins dimensions shown opposite for use in precision die sets. (Pins Available in Class 2) SHOULDER PINS For use with automotive, hardware, forming, or draw dies where stamping stock is thicker than 1/16, and clearances between punch and die sections will be more than.003 per side. (Pins available in Class 2) REMOVABLE PINS Designed specifi cally for all dies where it is desirable to remove pins for ease and simplicity of sharpening die. Lamina removable pins are generally used in carbide dies, progressive dies, lamination dies, and dies for very thin materials where clearances between punch and die sections will be no more than.0007 per side. Diameter TN Tolerance DIE PIN TOLERANCES Dimension Dimension ATN Tolerance HP Tolerance TPB & TPC Press TPC Press Diameter Tolerance Diameter

23 Guide Pins Pressed Fit GUIDE PIN STRAIGHT 4 TN-125-X-7 7 TN-750-X-4 TN-750-X-4-1/2 4-1/2 TN-125-X-7-1/2 7-1/2 TN-750-X-5 5 TN-125-X-8 8 3/4 TN-750-X-6 6 TN-125-X-8-1/2 8-1/2 TN-750-X-7 7 TN-125-X-9 1-1/4 9 TN-750-X-8 8 TN-125-X-9-1/2 9-1/2 TN-100-X-4 4 TN-125-X TN-100-X-4-1/2 4-1/2 TN-125-X TN-100-X-5 5 TN-125-X TN-100-X-5-1/2 5-1/2 TN-150-X-5 5 TN-100-X-6 6 TN-150-X-5-1/2 5-1/2 TN-100-X-6-1/2 6-1/2 TN-150-X TN-100-X-7 7 TN-150-X-6-1/2 6-1/2 TN-100-X-7-1/2 7-1/2 TN-150-X-7 7 TN-100-X-8 8 TN-150-X-7-1/2 7-1/2 TN-100-X-8-1/2 8-1/2 TN-150-X-8 1-1/2 8 TN-100-X-9 9 TN-150-X-8-1/2 8-1/2 TN-100-X TN-150-X-9 9 TN-125-X-4-1/2 4-1/2 TN-150-X-9-1/2 9-1/2 TN-125-X-5 5 TN-150-X TN-125-X-5-1/2 1-1/4 5-1/2 TN-150-X TN-125-X-6 6 TN-150-X TN-125-X-6-1/2 6-1/2 GUIDE PIN STRAIGHT WITH STEP LEAD ATN-175-X-6 6 ATN-200-X ATN-175-X-6-1/2 6-1/2 ATN-200-X ATN-175-X-7 7 ATN-200-X ATN-175-X-7-1/2 7-1/2 ATN-200-X ATN-175-X-8 8 ATN-250-X-8 8 ATN-175-X-8-1/2 8-1/2 ATN-250-X-8-1/2 8-1/2 ATN-175-X-9 9 ATN-250-X /4 ATN-175-X-9-1/2 9-1/2 ATN-250-X-9-1/2 9-1/2 ATN-175-X ATN-250-X /2 ATN-175-X ATN-250-X ATN-175-X ATN-250-X ATN-175-X ATN-250-X ATN-175-X ATN-250-X ATN-175-X ATN-250-X ATN-200-X-6 6 ATN-300-X-9 9 ATN-200-X-6-1/2 6-1/2 ATN-300-X ATN-200-X-7 7 ATN-300-X ATN-200-X-7-1/2 7-1/2 ATN-300-X ATN-200-X-8 8 ATN-300-X ATN-200-X-8-1/2 8-1/2 ATN-300-X ATN-200-X-9 9 ATN-300-X ATN-200-X ATN-300-X ATN-200-X-10-1/2 10-1/2 ATN-300-X ATN-200-X ATN-300-X TN TN pins are centerless ground. ATN ATN pins are centerless ground. TN and ATN pins are made of hardened steel with a precision-ground running diameter (), these guide pins are perfect mates for standard Lamina guide bushings. Please see bore size information on page

24 24 GUIDE PIN STRAIGHT - PRESS FIT END UNGROUND 4 TPB-750-X-4 TPB-750-X-4-1/2 4-1/2 TPB-750-X-5 5 TPB-750-X-5-1/2 3/ /2 TPB-750-X TPB-750-X-7 7 TPB-750-X-7-1/2 7-1/2 TPB-750-X-8 8 TPB-100-X-4 4 TPB-100-X-4-1/2 4-1/2 TPB-100-X-5 5 TPB-100-X-5-1/2 5-1/2 TPB-100-X-6 6 TPB-100-X-6-1/ /2 TPB-100-X TPB-100-X-7-1/2 7-1/2 TPB-100-X-8 8 TPB-100-X-8-1/2 8-1/2 TPB-100-X-9 9 TPB-100-X TPB-125-X-4 4 TPB-125-X-4-1/2 4-1/2 TPB-125-X-5 5 TPB-125-X-5-1/2 5-1/2 TPB-125-X-6 6 TPB-125-X-6-1/2 6-1/2 TPB-125-X-7 7 TPB-125-X-7-1/2 1-1/ /2 TPB-125-X-8 8 TPB-125-X-8-1/2 8-1/2 TPB-125-X-9 9 TPB-125-X-9-1/2 9-1/2 TPB-125-X TPB-125-X TPB-125-X TPB-150-X-4-1/2 4-1/2 TPB-150-X-5 5 TPB-150-X-5-1/2 5-1/2 TPB-150-X-6 6 TPB-150-X-6-1/2 6-1/2 TPB-150-X-7 7 TPB-150-X-7-1/2 7-1/2 TPB-150-X-8 8 TPB-150-X-8-1/2 1-1/ /2 TPB-150-X TPB-150-X-9-1/2 9-1/2 TPB-150-X TPB-150-X TPB-150-X TPB-150-X TPB-150-X TPB-150-X TPB-150-X L2 1-3/8 1-1/2 1-3/4 2 6 TPB-175-X-6 TPB-175-X-6-1/2 6-1/2 TPB-175-X-7 7 TPB-175-X-7-1/2 7-1/2 TPB-175-X-8 8 TPB-175-X-8-1/2 8-1/2 TPB-175-X-9 9 TPB-175-X-9-1/2 1-3/ /2 TPB-175-X TPB-175-X TPB-175-X TPB-175-X TPB-175-X TPB-175-X TPB-175-X TPB-200-X-6 6 TPB-200-X-6-1/2 6-1/2 TPB-200-X-7 7 TPB-200-X-7-1/2 7-1/2 TPB-200-X-8 8 TPB-200-X-8-1/2 8-1/2 TPB-200-X-9 9 TPB-200-X-9-1/ /2 2 TPB-200-X TPB-200-X TPB-200-X TPB-200-X TPB-200-X TPB-200-X TPB-200-X TPB-200-X TPB-250-X-8 8 TPB-250-X-8-1/2 8-1/2 TPB-250-X-9 9 TPB-250-X TPB-250-X TPB-250-X / TPB-250-X TPB-250-X TPB-250-X TPB-250-X TPB-250-X TPB-250-X TPB-300-X-9 9 TPB-300-X TPB-300-X TPB-300-X TPB-300-X TPB-300-X TPB-300-X TPB-300-X TPB-300-X TPB-300-X L2 2-1/4 2-1/2 3-1/2 4 Guide Pins Pressed Fit L2 TPB All TPB Guide Pins have centers and stock left on the diameter for grinding. See bore size information on page 18. TPB-375-X 3-3/4" diameters & L2 lengths as specified TPB-450-X 4-1/2 diameters & L2 lengths as specified Call for quotation on pins above.

25 TPC-750-X-4 L2 TPC-750-X-4-1/2 4-1/2 TPC-750-X-5 5 TPC-750-X-5-1/2 5-1/2 TPC-750-X-6 3/4 6 TPC-750-X-6-1/2 6-1/2 TPC-750-X-7 7 TPC-750-X-7-1/2 7-1/2 TPC-750-X-8 8 TPC-875-X-4 TPC-875-X-4-1/2 4-1/2 TPC-875-X-5 5 TPC-875-X-5-1/2 5-1/2 TPC-875-X-6 7/8 6 TPC-875-X-6-1/2 6-1/2 TPC-875-X-7 7 TPC-875-X-7-1/2 7-1/2 TPC-875-X-8 8 TPC-100-X-4 TPC-100-X-4-1/2 4-1/2 TPC-100-X-5 5 TPC-100-X-5-1/2 5-1/2 TPC-100-X-6 6 TPC-100-X-6-1/2 6-1/2 1 TPC-100-X-7 7 TPC-100-X-7-1/2 7-1/2 TPC-100-X-8 8 TPC-100-X-8-1/2 8-1/2 TPC-100-X-9 9 TPC-100-X TPC-125-X-4 TPC-125-X-4-1/2 4-1/2 TPC-125-X-5 5 TPC-125-X-5-1/2 5-1/2 TPC-125-X-6 6 TPC-125-X-6-1/2 6-1/2 TPC-125-X-7 7 TPC-125-X-7-1/2 1-1/4 7-1/2 TPC-125-X-8 8 TPC-125-X-8-1/2 8-1/2 TPC-125-X-9 9 TPC-125-X-9-1/2 9-1/2 TPC-125-X TPC-125-X TPC-125-X TPC-150-X-4-1/ /2 TPC-150-X-5 5 TPC-150-X-5-1/2 5-1/2 TPC-150-X-6 1-1/2 6 TPC-150-X-6-1/2 6-1/2 TPC-150-X-7 7 TPC-150-X-7-1/2 7-1/2 GUIDE PIN STRAIGHT PRESS FIT GROUND 1-3/8 1-1/2 1-1/2 1-3/4 2 TPC-150-X-8 L2 TPC-150-X-8-1/2 8-1/2 TPC-150-X-9 9 TPC-150-X-9-1/2 1-1/2 9-1/2 TPC-150-X TPC-150-X TPC-150-X TPC-175-X-6 TPC-175-X-6-1/2 6-1/2 TPC-175-X-7 7 TPC-175-X-7-1/2 7-1/2 TPC-175-X-8 8 TPC-175-X-8-1/2 8-1/2 TPC-175-X-9 9 TPC-175-X-9-1/2 1-3/4 9-1/2 TPC-175-X TPC-175-X TPC-175-X TPC-175-X TPC-175-X TPC-175-X TPC-175-X TPC-200-X-6 TPC-200-X-6-1/2 6-1/2 TPC-200-X-7 7 TPC-200-X-7-1/2 7-1/2 TPC-200-X-8 8 TPC-200-X-8-1/2 8-1/2 TPC-200-X-9 9 TPC-200-X-9-1/2 9-1/2 2 TPC-200-X TPC-200-X TPC-200-X TPC-200-X TPC-200-X TPC-200-X TPC-200-X TPC-200-X TPC-250-X-8 TPC-250-X-8-1/2 8-1/2 TPC-250-X-9 9 TPC-250-X TPC-250-X TPC-250-X /2 TPC-250-X TPC-250-X TPC-250-X TPC-250-X TPC-250-X TPC-250-X Not all pins ground on centers /4 2-1/2 3-1/2 TPC-300-X-9 L2 Specifi cations: L2 TPC-300-X TPC-300-X TPC-300-X TPC-300-X TPC-300-X TPC-300-X TPC-300-X TPC-300-X TPC-300-X TPC TPC-100 & smaller = nominal plus.0020 TPC = nominal plus.0025 TPC-375 & 450 = nominal plus TPC-375-X 3-3/4" diameters & L2 lengths as specified TPC-450-X 4-1/2 diameters & L2 lengths as specified Call for quotation on pins above

26 Guide Pins Pressed Fit Metric Solid & Hollow These pins are made especially for automotive stamping companies. They conform to the standards agreed to by the North American Automotive Metric Standards group. AUTOMOTIVE METRIC NAAMS STANDARD 32, 40, 50 & 63 Dia. guide posts have M8 x thread; 80, 100, 115 & 125 Dia. guide posts have M12 x thread to facilitate handling from deep freeze. 26 GUIDE PIN STRAIGHT NAAMS SOLID HOLLOW Tol Tol g6 r6 D4 Hollow Pins only GROUND UNGROUND GROUND G G512512UG 125 G G512514UG G G512516UG G G512518UG 180 G G513214UG 140 G G513216UG G G513218UG G G513220UG 200 G G514014UG 140 G G514016UG 160 G G514018UG G G514020UG G G514022UG 225 G G514025UG 250 G G515016UG G G515018UG 180 G G515020UG G G515022UG G G515025UG 250 G G515028UG 280 G G515031UG 315 G G516318UG 180 G G516320UG 200 G G516322UG 225 G G516325UG G G516328UG G G516331UG 315 G G516335UG 355 G G516340UG 400 G G516350UG 500 G G518022UG 225 G G518025UG 250 G G518028UG 280 G G518031UG G G518035UG G G518040UG 400 G G518045UG 450 G G518050UG 500 G G511031UG GH G G511035UG GH G G511040UG GH G G511045UG GH G G511050UG GH G G511055UG GH G G511060UG GH G G511065UG 650 G G511140UG G G511150UG G G511235UG GH G G511240UG GH G G511245UG GH G G511250UG GH G G511255UG GH G G511260UG GH G G511265UG GH G M x 30mm Deep D4 HOLLOW PIN Please see bore size information on page 18.

27 Guide Pins Pressed Fit Metric GUIDE PINS STRAIGHT METRIC 120 TN-25MM-X TN-19MM-X-120 TN-19MM-X TN-25MM-X TN-19MM-X TN-25MM-X TN-19MM-X TN-25MM-X TN-19MM-X TN-32MM-X TN-19MM-X TN-32MM-X TN-19MM-X TN-32MM-X TN-19MM-X TN-32MM-X TN-19MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN-32MM-X TN-25MM-X TN -Metric TN pins are designed to be pressed into place. The ground bearing surface is equal top to bottom. STRAIGHT GUIDE PINS METRIC UNGROUND L2 L2 TPB-40MM-X TPB-50MM-X TPB-40MM-X TPB-50MM-X TPB-40MM-X TPB-50MM-X TPB-40MM-X TPB-50MM-X TPB-40MM-X TPB-50MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-40MM-X TPB-63MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB-80MM-X TPB-50MM-X TPB - Metric L2 All TPB Guide Pins have centers and stock left on the diameter for grinding. 27

28 Guide Pins Tap Fit Lamina demountable guide pins are tap fit and require toe clamps and screws to hold them in place. L5 The clamping flange is ground so that the flange fits squarely against the mounting surface. Please see pages 16 & 17 for toe clamp placement information and bore size information on page Heavy-duty X-40-Clamps are used to secure the pins to the die shoe. Clamps and screws are included. 28 & NOM. PIN DIA ±.010 ±.010 GUIDE PINS DEMOUNTABLE L5 (Ref.) # of CLAMPS & NOM. PIN DIA ±.010 ±.010 L5 (Ref.) DGP DGP DGP DGP DGP DGP / DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP / DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP / DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP / DGP DGP DGP DGP # of CLAMPS 3 3 4

29 Guide Pins Tap Fit Lamina demountable guide pins are tap fit and require toe clamps and screws to hold them in place. L5 The clamping flange is ground so that the flange fits squarely against the mounting surface. Please see pages 16 & 17 for toe clamp placement information and bore size information on page Heavy-duty X-40-Clamps are used to secure the pins to the die shoe. Clamps and screws are included. & NOM. PIN DIA ±.010 ±.010 GUIDE PINS DEMOUNTABLE L5 (Ref.) # of CLAMPS & NOM. PIN DIA ±.010 ±.010 L5 (Ref.) DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP / DGP DGP DGP / DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP DGP / DGP # of CLAMPS

30 Guide Pins Pressed Fit 30 Shoulder type guide pins are for use with automotive, hardware, forming, or draw dies where stamping stock is thicker than 1/16, and clearances between punch and die sections will be more than.003 per side. Shoulder type guide pins are also valuable for repair of damaged dies where straight type pins no longer fit. NOM. PIN DIA. (Pins available in Class 2) GUIDE PINS WITH SHOULDERS PRESS DIA. L2 NOM. PIN DIA. PRESS DIA. HP-100-X-5-1/2 5-1/2 HP-200-X-8 8 HP-100-X-6 6 HP-200-X-8-1/2 8-1/2 HP-100-X-6-1/2 6-1/2 HP-200-X /2 1-1/2 HP-100-X-7 7 HP-200-X HP-100-X-8 8 HP-200-X /2 HP-100-X-9 9 HP-200-X /2 HP-125-X-6 6 HP-200-X HP-125-X-7 7 HP-200-X HP-125-X-7-1/2 1-1/4 1-3/4 7-1/2 2 HP-200-X HP-125-X-8 8 HP-200-X HP-125-X-9 9 HP-250-X-9 9 HP-150-X-6 6 HP-250-X HP-150-X-6-1/2 6-1/2 HP-250-X HP-150-X-7 7 HP-250-X /2 3 HP-150-X-7-1/2 7-1/2 HP-250-X HP-150-X-8 8 HP-250-X HP-150-X-8-1/2 8-1/2 HP-250-X / /2 HP-150-X-9 9 HP-250-X HP-150-X HP-300-X HP-150-X HP-300-X HP-150-X HP-300-X / HP-150-X HP-300-X HP-150-X HP-300-X HP-175-X-7-1/2 7-1/2 HP-300RA-X HP-175-X-8 8 HP-300RA-X HP-175-X-9 9 HP-300RA-X /2 5 HP-175-X HP-300RA-X /4 2-1/4 3 HP-175-X HP-300RA-X HP-175-X HP-300RA-X HP-175-X HP Pins can be manufactured in 3 3 /4 and 4 1 /2 HP-175-X diameters in various lengths. See page 22. L2 L2 HP dimension is supplied with approximately.016 grindstock. HP Shoulder pins are meant to be press fit into place. 1/4 R

31 Guide Pins Tap Fit Metric Lamina has a wide variety of pins to meet most tool room requirements. Applications: Transfer Presses Repairs See page 17 for clamp placement instructions. GUIDE PINS WITH SHOULDERS METRIC TOL g6 TOL r6 L5 G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G G L5 6 32, 40, 50 & 63 Dia. guide posts have M8 x thread; 80, 100, 115 & 125 Dia. guide posts have M12 x thread to facilitate handling from deep freeze. Must be held in place with toe clamps. G720000C toe clamps & screws are included. See pages 16 & 17 for clamping information; bore size information on page

32 32 GUIDE PIN REMOVABLE Nom. L2 Length Pin Dia. Tapped Hole RP-100-X RP-100-X-5-1/ RP-100-X Pin End RP-100-X-6-1/ /16 18x3/4 RP-100-X RP-100-X-7-1/2 Install End RP-100-X /16 18 RP-100-X-8-1/ RP-100-X RP-125-X-5-1/ RP-125-X RP-125-X-6-1/ RP-125-X RP-125-X-7-1/ Pin End RP-125-X /16 18x7/8 RP-125-X-8-1/ RP-125-X-9 Install End RP-125-X /8 16 RP-125-X RP-125-X RP-125-X RP-125-X RP-150-X-5-1/ RP-150-X RP-150-X-6-1/ Pin End RP-150-X /8 16x1 RP-150-X-7-1/ RP-150-X-8 Install End RP-150-X-8-1/ /8 16 RP-150-X RP-150-X RP-175-X RP-175-X-7-1/ Pin End 3/8-16x1 RP-175-X RP-175-X-8-1/ Install End RP-175-X /8-16 RP-175-X RP-200-X RP-200-X RP-200-X-7-1/ RP-200-X Pin End RP-200-X-8-1/ /8-16x7/8 RP-200-X RP-200-X-10 Install End RP-200-X /8-16 RP-200-X RP-200-X RP-200-X RP-250-X RP-250-X Pin End 1/2-13x1 RP-250-X RP-250-X Install End RP-250-X /2-13 RP-250-X RP-300-X Non-stock, call for quotation. Guide Pins Removable Pressed Fit Bushing Liner Designed specifically for all dies where it is desirable to remove pins for ease and simplicity of sharpening die. Lamina removable pins are generally used with carbide dies, progressive dies, lamination dies, and dies for very thin materials where clearances between punch and die sections will be no more than.0007 per side. Can be used with Plain Bearing & Keyless Ball-Bearing Bushing and Retainers. 3/8 L2 2 2 REMOVABLE PIN * BUSHING LINER END CAP SOCKET HEAD CAP SCREW Tapped Hole Pin End Tapped Hole Install End ASSEMBLIES FOR REMOVABLE PINS GROUND UNGROUND Nom Pin Diam. GRP-100-ASSY GRP-100-ASSY GRP-125-ASSY GRP-125-ASSY GRP-150-ASSY GRP-150-ASSY GRP-175-ASSY GRP-175-ASSY GRP-200-ASSY GRP-200-ASSY GRP-250-ASSY GRP-250-ASSY GRP-300-ASSY GRP-300-ASSY Assembly includes 1 bushing liner, 1 End Cap & 1 Socket Head Cap Screw BUSHING LINERS FOR REMOVABLE PINS Nom * GROUND UNGROUND Pin O.D. Length Diam. GNRB-100 NRB GNRB-125 NRB GNRB-150 NRB GNRB-175 NRB GNRB-200 NRB GNRB-250 NRB GNRB-300 NRB *.016 stock left on this diameter on unground liner for grinding to fi t bored hole in die shoe END CAPS FOR REMOVABLE PINS Nom Soc. Head Pin Diam. O.D. Screw GRP-100-ASSY /16-18x1 GRP-125-ASSY /8-16x1 GRP-150-ASSY /8-16x1 GRP-175-ASSY /8-16x1 GRP-200-ASSY /8-16x1 GRP-250-ASSY /2-13x1.5 GRP-300-ASSY /2-13x1.5 Removable pins, assemblies and screws are sold separately.

33 SOLUTIONS TO FIT YOUR SPECIAL APPLICATIONS In addition to made to print specials, a wide range of catalog components can be modifi ed to meet customer specifi c applications. Round, fl at, simple or complex, we want to make those one-of-a-kind parts for you. At Lamina, our focus is on offering specials to you quickly and at a reasonable price. Please send your prints and requests for quotation to sales@lamina.com. 33

34 Stripper Bushings Clamp & Pressed Fit Types Lamina manufactures components specifi cally for use in dies where stripping operations take place such as in lamination dies. These components are made to close tolerances. GROUND UNGROUND* STRIPPER GUIDE PIN BUSHINGS BRONZE-PLATED Assembly includes bushing, clamps and screws. Nom Pin Diam. D4 L2 Bolt Circle Dia. # of "D" Clamps L2 * GCG-75 CG-75 3/ GCG-100 CG *.016" grind stock on these diameters. D4 STRIPPER BUSHINGS BRONZE PLATED PRESS FIT TYPE Nom Pin D GROUND UNGROUND* Diam GHG-62 HG-62 5/ GHG-75 HG-75 3/ GHG-100 HG *.016 grind stock on these diameters. D4 * STRIPPER BUSHINGS STRAIGHT TYPE Nom Pin L GROUND UNGROUND* Diam GSG-100-L SG-100-L *.020" grind stock on these diameters * 34

35 Stripper Pins Pressed Fit & Flange Types STRIPPER PINS PRESS FIT TYPE Nom. Pin Diam. * L2 SGP-62-X-4 5/ SGP-62-X-5 5/ SGP-75-X-5 3/ SGP-75-X-6-1/2 3/ SGP-100-X-6-1/ SGP-100-X-7-1/ * The diameter is unground. Suggested fi nish grind size for dimension to be.001 over nominal pin diameter. L2.406 * 3/4 1/4" G Screw CG Type DIE SHOE STRIPPER PLATE DIE RETAINER DIE SHOE HG Type R1 L2 STRIPPER PIN & BUSHING APPLICATION Nom. Pin Diam. F /8 STRIPPER PIN FLANGE STYLE * ± L2 R1 "G" Screws Flat Head ".250 F Soc. Head F Soc. Head F Soc. Head F / Soc. Head * The diameter is unground. Suggested fi nish bore size to be.005 over nominal pin diameter. 35

36 HEAVY DUTY STOCK LIFTERS MODEL 75 HARDENED, GROUND AND VENTED Rockwell: RC Case Hardened Deep Packaged complete with spring, screw and retaining washer W Dia. R Dia. U T S V Radius PURPOSE Available as Replacement Part No. DL75 Die Life Retaining Washer. 6 per package. Includes fl at head socket screw 5/16-18x1. Note: In blanking die sections order optional Die Life DL Retaining Washers: Counterbore hole must be deeper. When ordering please specify: 1. Quantity 2. Catalog Number Lifters with travel greater than 1.75 are available. Priced on application. (Furnished without spring.) DIE LIFE REPLACEMENT RETAINING WASHER & SCREW KIT R S T U V W DL LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for Lifter Body F Slot Length MODEL 75 Stock Lifter O.D (For Stock up to.094 thick) A TRAVEL LIFTER SPECIFICATIONS MODEL 75 B LIFTER C LIFTER POCKET D SPRING POCKET E SPRING FREE F SLOT REPLACE- MENT DIE SPRING 1/10" SPRING DEFL M113L M115L M115AL M115BL M115CL M115DL 1.2 d Counterbore a.187 h g b c REAM i f Counterbore in stripping plate j Replacement Washer #75WASHER Replacement Screw #75SCREW Die Life Package #DL75 (6 per package) F p A Travel VALUES CONSTANT FOR ALL "75" LIFTERS a.578 Dimension between CL of Lifter Pocket to CL of Socket Screw b.203 Slot Depth ±.005 c.750 Pocket Diameter for Lifter Body / d.688 Counter Bore Diameter for Lifter Washer f.25 Counter Bore Depth in Stripper Plate, minus half of stock thickness g.781 Counter Bore Diameter in Stripper Plate h.7495 Lifter Body Diameter / i.125 Slot Height (for Stock) ±.005 j.187 Dimension from Top of Slot to Top of Body ±.005 k Length of Spring Pocket in Lifter Body m.50 Spring Pocket Diameter n Dimension from Bottom of Washer (Slot) to Bottom of Body p.375 Counter Bore Depth for Washer & Socket Screw n.156 5/16-18 x 5/8 Socket Button Head Screw m k E B C D 36

37 HEAVY DUTY STOCK LIFTERS MODEL 112 HARDENED, GROUND AND VENTED Rockwell: RC Case Hardened Deep Packaged complete with spring, screw and retaining washer W Dia. R Dia. U T S V PURPOSE Available as Replacement Part No. D12 Die Life Retaining Washer. 6 per package. Includes fl at head socket screw 3/8-16x1-1/4. Note: In blanking die sections order optional Die Life DL Retaining Washers: Counterbore hole must be deeper. When ordering please specify: 1. Quantity 2. Catalog Number Lifters with travel greater than 1.75 are available. Priced on application. (Furnished without spring.) DIE LIFE REPLACEMENT RETAINING WASHER & SCREW KIT R S T U V W D LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for Lifter Body F Slot Length b MODEL 112 Stock Lifter O.D (For Stock up to.156 thick) d Counterbore c REAM LIFTER SPECIFICATIONS MODEL 112 A TRAVEL B LIFTER C LIFTER POCKET D SPRING POCKET E SPRING FREE F SLOT REPLACE- MENT DIE SPRING 1/10" SPRING DEFL M4L M6L M8L 6.4 a g f Counterbore in stripping plate M10L M11BL M11CL h i j Replacement Washer #112 WASHER Replacement Screw #112 SCREW Die Life Package #D12 (6 per package) F p A Travel VALUES CONSTANT FOR ALL "112" LIFTERS a.828 Dimension between CL of Lifter Pocket to CL of Socket Screw b.329 Slot Depth ±.005 c Pocket Diameter for Lifter Body / d.875 Counter Bore Diameter for Lifter Washer f.50 Counter Bore Depth in Stripper Plate, minus half of stock thickness g Counter Bore Diameter in Stripper Plate h Lifter Body Diameter / i.188 Slot Height (for Stock) ±.005 j.406 Dimension from Top of Slot to Top of Body ±.005 k Length of Spring Pocket in Lifter Body m.75 Spring Pocket Diameter n Dimension from Bottom of Washer (Slot) to Bottom of Body p.394 Counter Bore Depth for Washer & Socket Screw n.156 3/8-16 x 1.00 Socket Button Head Screw m k E B C D 37

38 HEAVY DUTY RAIL STOCK LIFTER PINS MODEL T-750 HARDENED, GROUND AND VENTED Rockwell: RC Case Hardened Deep Package complete with spring, screw and retaining washer. When ordering please specify: 1. Quantity 2. Catalog Number 5/16-18 x.625 tap LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for F Slot length Lifter Body G Top of Die to Top of Lifter Body d Counter bore c REAM Rail Stock Lifter O.D A TRAVEL B LIFTER C & D LIFTER POCKET G E SPRING FREE F SLOT REPLACE- MENT DIE SPRING 1/10" SPRING DEFL. a Rail & Screw Not Furnished T M113L 4.5 T M115L T M115AL 2.5 T M115BL 2.1 T M115CL 1.4 T M115DL 1.2 G F p h Optional: Tack Weld at As- A Travel Replacement Washer Part Number 75WASHER Replacement Screw Part Number 75SCREW.156 B n VALUES CONSTANT FOR ALL 75-T LIFTERS a.578 Dimension between CL of Lifter Pocket to CL of Socket Screw c.750 Pocket Diameter for Lifter Body / d.688 Counter Bore Diameter for Lifter Washer h.7495 Lifter Body Diameter / i.125 Slot Height (for Stock) ±.005 j.187 Dimension from Top of Slot to Top of Body ±.005 k Length of Spring Pocket in Lifter Body n Dimension from Bottom of Washer (Slot) to Bottom of Body p.375 Counter Bore Depth for Washer & Socket Screw C & D 5/16-18 x 5/8 Socket Button Head Screw k E 38

39 HEAVY DUTY RAIL STOCK LIFTER PINS MODEL 112T HARDENED, GROUND AND VENTED Rockwell: RC Case Hardened Deep Package complete with spring, screw and retaining washer. When ordering please specify: 1. Quantity 2. Catalog Number 3/8-16 x 1 tap LIFTER SPECIFICATIONS A Operating Travel D Pocket Depth for Spring B Lifter Body Length E Spring Free Length C Pocket Depth for F Slot length Lifter Body G Top of Die to Top of Lifter Body d Counter bore c Ream Rail Stock Lifter O.D a A TRAVEL B LIFTER C & D LIFTER POCKET G E SPRING FREE F SLOT REPLACE- MENT DIE SPRING 1/10" SPRING DEFL. 112T M4L Rail & Screw Not Furnished 112T M6L T M8L T M10L T M11BL T Replacement Washer Part Number 112WASHER M11CL 3.8 Replacement Screw Part Number 112SCREW G F p.156 h Optional Tack Weld at Assembly A Travel B n VALUES CONSTANT FOR ALL 112-T LIFTERS a.828 Dimension between CL of Lifter Pocket to CL of Socket Screw c Pocket Diameter for Lifter Body / d.875 Counter Bore Diameter for Lifter Washer h Lifter Body Diameter / i.188 Slot Height (for Stock) ±.005 j.406 Dimension from Top of Slot to Top of Body ±.005 k Length of Spring Pocket in Lifter Body n Dimension from Bottom of Washer (Slot) to Bottom of Body p.394 Counter Bore Depth for Washer & Socket Screw C & D 3/8-16 x 1.00 Socket Button Head Screw k E 39

40 Mini-Lifters Top or Side Mounted 3/8 and 1/2 diameters each to 3 different lengths. Hardened, ground and vented. Accurately machined from solid bar steel and packaged complete with spring, socket head cap screw, dog point screw and retaining washer. Immediately available from Inventory. ML ML ML OPTIONAL DIE LEVEL FULL SCALE TEMPLATE ML ML ML R.130 ± Air Relief.160 Width of slot 1 /4-20 Dog Pt. Screw & Lock Nut Ream.500 Dia. Dog Point Washer Note: Can be guided by dog point washer or dog point screw Dog Pt. Screw & Lock Nut.130 Width of Slot.38R.130 ± Ream.375 Dia. Air Relief.355 A TRAVEL B C BORE D MIN. E PRELOADED SPRINGS F SLOT REPLACEMENT DIE SPRING SPRING FREE 1/10 SPRING DEFLECTIONS ML M111L ML M112L ML M113L A TRAVEL B C BORE D MIN. E PRELOADED SPRINGS F SLOT REPLACEMENT DIE SPRING SPRING FREE 1/10 SPRING DEFLECTIONS ML M101L ML M102L ML M103L Dia..12 ML Dia Dia ML Dia..155 B.54 Opt..10 A Travel.16 1 /4-20x.5 Screw.62 F B Opt. A Travel x.38 Screw.62 F C E D Min /8 Initial Spring Comp. 4 to 1 Ratio C E D Min.

41 Design in (and build in) stock lifters just as easily as you do die springs and pins. Standard notched lifters are made in two sizes to handle stock up to.156 thick. Side center-rail lifters that easily accept your special rails are also offered. These lifters all install from the top only. Easier to do and they can be replaced without taking the die from the press. All they need are two drilled holes, one tapped. Drop the spring and lifter in the larger one and secure them with the retaining screw in the tapped hole. Go to standard lifters for consistent quality they re all solid bar steel, hardened, ground and vented. You can t build them yourself for less. REPLACEMENT S REPLACEMENT SPRINGS REPLACEMENT WASHERS REPLACEMENT SCREWS DIE LIFE KIT 6 SETS T T T T T T T T T T T T-1-75 ML ML ML ML ML ML M113L M115L M115AL M115BL M115CL M115DL M4L M6L M8L M10L M11BL M11CL M101L M102L M103L M111L M112L M113L 75WASHER 75SCREW DL75 112WASHER 112SCREW D12 38WASHER 50WASHER 41

42 LIFTER PINS METRIC Lifter pins are manufactured from 1144 steel and are commonly used to handle large die sets. They conform to NAAMS standards. The internal spring provides added assurance that the fall ring will function properly during the course of the pin s use. NAAMS Code A B C D E F Total Die Wt. in Metric Tons (t) LP L LP L LP L LP L

43 STOP BLOCKS These stop blocks are precision machined from 1018 material. Additionally, the blocks are inspected to provide uniform quality and dimensions. The length dimension is.060 oversize. Diameter D Length A CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB CSB

44 S1 Socket Set Screw S2 Socket Head Cap Screw PAD RETAINERS LOCKING INCH, STANDARD MOUNT Pad retainers are manufactured from 1144 steel and hardened to Rockwell C-scale. They are machined to precise tolerances in order to retain the pad and assure parallelism during use. The NP Series is also available, by special order, that offers three prongs as opposed to knurl. Diam. Diam. Length ±.005 L2 L S1 S2 5/8-18 5/16-18 ASSEMBLY INCLUDES: Retainer Body Socket Head Cap Screws Socket Set Screw Diam. Diam. ±.005 Length /8-18 5/ /8-14 1/ /8-12 5/ /4-16 3/ /4-12 3/4-10 7/8-14 1/ L2 L4 NO. RADIUS S1 LOAD RATING lbs. 100-XXX , XXX , XXX , XXX , XXX , XXX ,000 S2

45 S1 Socket Set Screw S2 Socket Head Cap Screw PAD RETAINERS LOCKING INCH, STANDARD MOUNT, WITH FLATS Diam. Diam. ±.005 Length L2 L F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F F S1 S2 5/8-18 5/16-18 ASSEMBLY INCLUDES: Retainer Body Socket Head Cap Screws Socket Set Screw Diam. Diam. ±.005 Length F /8-18 5/ F F /8-14 1/ F F F F F F F F F F F /8-12 5/ F /4-16 3/ F F F F F F F F F F F F F F /4-12 3/4 - N10 7/8-14 1/ F F F F F F F L2 NO. L4 F RADIUS S1 LOAD RATING lbs. 100-XXX , XXX , XXX , XXX , XXX , XXX ,000 S2

46 PAD RETAINERS LOCKING INCH, REVERSE MOUNT, WITH FLATS Pad retainers are manufactured from 1144 steel and hardened to Rockwell C-scale. They are machined to precise tolerances in order to retain the pad and assure parallelism during use. NO. F RADIUS LOAD RATING lbs. 100-XXXR , XXXR , XXXR , XXXR , XXXR , XXXR , Diam. Diam. ±.005 Length R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 6.00 G T / / /8-16 Diam. Diam. ±.005 Length R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R R 6.00 G T / / /4-10

47 PAD RETAINERS STANDARD AND REVERSE MOUNT METRIC Pad retainers are manufactured from 1144 steel and hardened to Rockwell C-scale. They are machined to precise tolerances in order to retain the pad and assure parallelism during use. STANDARD MOUNT REVERSE MOUNT S1 Socket Set Screw S2 Socket Head Cap Screw L2 S1 S2 LOAD RATING NR M27 X 2 M16 X kn NR M36 X 3 M20 X kN F LOAD RATING NR kn NR kN Diameter Length NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR NR Diameter Diameter Length NR50-30R 30 NR50-40R 40 NR50-45R 45 NR50-50R 50 NR50-60R 60 NR50-65R 65 NR50-70R NR50-75R 75 NR50-90R 90 NR50-100R 100 NR50-115R 115 NR50-130R 130 NR50-140R 140 NR50-160R 160 NR70-40R 40 NR70-45R 45 NR70-50R 50 NR70-60R 60 NR70-65R 65 NR70-70R 70 NR70-75R NR70-90R 90 NR70-100R 100 NR70-115R 115 NR70-130R 130 NR70-140R 140 NR70-160R 160 Diameter