Connecting a Remote UR-V Enhanced Front Panel to a Vertically-Mounted Horizontal UR Device Instruction Sheet

Transcription

1 GE Digital Energy UR Family Connecting a Remote UR-V Enhanced Front Panel to a Vertically-Mounted Horizontal UR Device Instruction Sheet GE Publication Number: GEK A GE Document Part Number: A2 Copyright 2015 GE Multilin Inc. This document outlines how to use a UR horizontal enhanced front panel mounting kit, part number , which allows remote use of a vertical front panel with a vertically-mounted horizontal UR device. Overview The installation allows remote use of a vertical UR front panel. The front panel is removed from the UR device and a cover panel is installed. The UR device is then connected remotely to a front panel. The figure shows the concept. Figure 1: Remote use of UR front panel using UR front panel mounting kit CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 1

2 The kit includes a cover panel, mounting brackets, cables, and screws. If you do not have a vertical front panel, order it separately. Table 1: Parts list Part number Quantity Description x 3/8" pan head Phillips screw #8-32X1/4" flat head Phillips black screw lock nut Washer flat zinc number #8 external star washer #8-32 x ¼ Phillips screw RJ45 cable twisted pair Cat6 black straight through coupler " ground cable Mounting bracket 18A UR horizontal side mount cover panel Dimensions There are two cutouts required to attach the UR-V enhanced front panel and the vertically-mounted horizontal UR device. To prepare the customer panels: 1. Make the modifications to the customer panels as shown in the figures. Figure 2: Horizontal UR device mounting hole dimensions 2 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

3 Figure 3: UR-V enhanced front panel mounting holes and cutout dimensions CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 3

4 Procedures After preparing the customer panels, the following four steps are required to install the kit: Attach the UR front panel to the customer panel Attach the mounting brackets and cover panel to the UR device Attach the UR device to the customer panel Connect the wires Disconnect power to the UR device, else death or serious injury can result. Attach the UR front panel to the customer panel To attach the UR-V enhanced front panel to the customer panel: 1. Feed the RJ45 connector cable on the UR-V front panel through the RJ45 connector cutout on the customer panel. 4 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

5 2. Using four # /8 screws (part number ), four #10 zinc washers (part number ), and four nylock zinc nuts (part number ), attach the UR-V front panel to the customer panel. Figure 4: Attach the vertical front panel to the customer panel CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 5

6 3. Tighten the screws using a tightening torque of 20 lb.-in, ensuring that the UR-V enhanced front panel is snug to the customer panel. Figure 5: Tighten screws and nuts 6 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

7 Attach the mounting brackets and cover panel to the UR device The second step is to attach the mounting brackets and vertical mount cover to the chassis. If your chassis already has the mounting brackets and vertical mount cover attached, then go to the next step/section. To attach the brackets and cover to the UR device: 1. Using four #8-32 ¼ screws (part number ), attach the mounting bracket (part number ) to the top of the chassis (tightening torque 17 lb.-in). Figure 6: Attach mounting bracket to top of UR CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 7

8 2. Using four #8-32 ¼ screws (part number ), attach the mounting bracket (part number ) to the bottom of the chassis (tightening torque 17 lb.-in). Figure 7: Attach mounting bracket to bottom of UR 3. From the cover panel (part number 18A0-0523), plug the RJ45 cable into the RJ45 connector on the CPU module of the UR. Figure 8: Connect RJ45 cable from cover panel to UR device 4. Plug the ground cable from the UR device to the ground clip on the cover panel. 8 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

9 5. Using two #8-32 ¼ screws (part number ) and two lock washers (part number ), attach the side-mount cover panel to the top of the chassis (tightening torque 17 lb.-in). Figure 9: Connect cover panel to top of UR CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 9

10 6. Using two #8-32 ¼ screws (part number ) and two lock washers (part number ), attach the cover panel to the bottom of the chassis (tightening torque 17 lb.-in). Figure 10: Connect cover panel to bottom of UR 10 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

11 Attach the UR device to the customer panel The third step is to attach the horizontal UR device to the customer panel. To attach the UR device to the customer panel: 1. Using four # /8 screws (part number ), four #10 zinc washers (part number ), and four nylock zinc nuts (part number ), attach the UR device to the customer panel starting from the bottom. Figure 11: Attach UR device to customer panel CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 11

12 2. Tighten the screws using a tightening torque of 20 lb.-in, ensuring that the UR device is snug to the customer panel. Figure 12: Tighten screws and nuts 12 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

13 Connect wires The final step is to complete the electrical connections between the remote front panel and the UR cover panel/ device. When complete, the UR-V enhanced front panel is connected to a vertically-mounted horizontal UR device as shown. Figure 13: Completed installation CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 13

14 To connect the remote front panel and UR device: 1. Connect one end of the RJ45 cable (part number ) to the UR device as shown here. 2. Connect one end of the ground cable (part number ) to the UR device as shown here. Figure 14: Connect cables to UR device 3. Connect the other end of the ground cable through the cutout on the panel and attach it to the rear of the UR-V enhanced front panel. Figure 15: Connect ground cable to front panel 14 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET

15 4. Connect the other end of the RJ45 cable to the RJ45 cable on the UR-V front panel with the RJ45 straight-through coupler (part number ). Figure 16: Connect RJ45 cable with coupler to front panel For further assistance For product support, contact the information and call center as follows: GE Digital Energy 650 Markland Street Markham, Ontario Canada L6C 0M1 Worldwide telephone: Europe/Middle East/Africa telephone: North America toll-free: Fax: Worldwide multilin.tech@ge.com Europe multilin.tech.euro@ge.com Website: CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET 15

16 16 CONNECTING REMOTE UR-V ENHANCED FRONT PANEL TO VERTICALLY-MOUNTED HORIZONTAL UR DEVICE - INSTRUCTION SHEET