DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION HVAC VALVES
|
|
- Jesse McDonald
- 5 years ago
- Views:
Transcription
1 DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION PART 1 GENERAL 1.01 DESCRIPTION A. Provide valves for the following systems: 1. Heating Hot Water 2. Chilled Water 3. Condenser Water 4. Glycol Solutions 5. Low Pressure Steam and Condensate 1.02 QUALITY ASSURANCE A. Standards: American National Standards Institute (ANSI), American Society of Mechanical Engineers, (ASME), Manufacturer's Standardization Society of the Valve and Fittings Industry (MSS). B. Valves shall be rated at least 20% over the maximum system working pressure. PART 2 PRODUCTS 2.01 HVAC systems with operating temperatures up to 200 degrees F. For heating hot water, chilled water, condenser water glycol solutions, heat recovery and make-up water. A. Valve Function Start/Stop Flow 2 Piece Standard Port Ball (600 WOG) Body Material Cast Bronze (ASTM B 584) Seal Material Reinforced PTFE Ball Material Material Lever 13-HC
2 B. Valve Function Start/Stop Flow Butterfly Minimum ANSI Class 125/150 Body Material Cast Iron Seat Material EPDM Full Lug Flange Material Aluminum Bronze Shaft Material 316 or 17-4 PH Stainless Steel Lever with Memory Stop, Gear for 6" and Larger Other Valves and Seats shall be rated for 150 psi shutoff during dead-end service, without down stream piping or flange. C. Valve Function Regulate Flow (200 WOG) Rising Hand Wheel D. Valve Function Regulate Flow (200 WOG) Solid Cast Bronze (ASTM B 62) Seat Ring Cast Bronze (ASTM B 62) Hand Wheel E. Valve Function Prevent Back flow Check - Horizontal Swing or Vertical Lift (200 WOG) Cap HC1-033
3 F. Valve Function Prevent Back Flow Swing check (200 WOG) Cast Iron (ASTM A 126) Seat Ring Bronze (ASTM B 62) Cap G. Valve Function Prevent Back Flow Body Silent Check Valve Body Material Cast Iron (ASTM A 48, Class 35) Cast Iron with Bronze Face Rings Seat Bronze (ASTM B584) Plug Bronze (ASTM B584) Spring Stainless Steel T304 (ASTM A 276) H. Acceptable manufacturers are: NIBCO, Milwaukee, Crane, DeZurik, Watts, Keystone, Mueller, or Stockham HVAC Steam Systems with operating pressure up to 15 psig and temperatures up to 250 degrees F. Including low pressure steam, condensate, and feed water. A. Valve Function Start/Stop Flow Gate Solid Wedge - Bronze (ANSI B 62) Union Non-Rising Malleable Iron Hand Wheel B. Valve Function Start/Stop Flow 2 Piece Standard Port Ball Body Material Bronze Seal Material Reinforced PTFE Ball Material Material Lever C. Valve Function Start/Stop Flow 13-HC
4 Gate Solid Wedge - Cast Iron (ASTM A 126) Wedge and Seat Rings Cast Bronze ( ASTM B 62) O.S. & Y Cast Iron Hand Wheel D. Valve Function Regulate Flow 420 Stainless Steel (ASTM A 276) Seat Ring 420 Stainless Steel (ASTM A 276) or Union Rising Malleable Iron Hand Wheel E. Valve Function Regulate Flow Seat Ring Bronze (ASTM B 62) O.S. & Y Lever, Gear for 6" & larger F. Valve Function Prevent Back Flow Check - Horizontal Swing Teflon or HC1-033
5 G. Valve Function Prevent Back Flow Check - Horizontal Swing Cast Iron with Bronze Face Rings H. Acceptable are: NIBCO, Milwaukee, Watts, Stockham or Crane. PART 3 EXECUTION 3.01 INSTALLATION OF VALVES A. Valves shall be installed as called for in the Specifications, at locations shown on the Drawings, and as required to facilitate the maintenance, operation and servicing of all HVAC piping systems. B. Valves shall be installed at service connections to equipment, at branch take-off lines, at mains at low points for draining, and at high points for venting. C. Valves shall be installed with the hand wheel at or above the centerline of the pipe. D. Valves installed in copper lines shall be provided with screwed or flanged adapters with a union installed downstream and within 12 inches of the valve. E. Valves shall be installed in accessible locations. Provide chain wheel and chain for all valves located with the lowest portion of its handwheel or lever at 10 feet or more above the finished floor. F. Install shutoff and gate drain valves in branches and risers. END OF SECTION 13-HC
Brown University Revised August 3, 2012 Facilities Design & Construction Standards SECTION HVAC&R VALVES
SECTION 23 05 23 HVAC&R VALVES PART 1 - GENERAL 1.1 SUMMARY: A. Section includes valves for building services piping. 1.2 GENERAL VALVE APPLICATION REQUIREMENTS: A. Provide valve handle extensions that
More informationDivision 23 - HVAC Section Switzerland Beallsville K-12 GENERAL DUTY VALVES FOR HVAC PIPING
SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and General Provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION VALVES
PART 1 GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions Specification Sections, apply to this Section. B. Related Sections:
More informationSECTION GENERAL-DUTY VALVES FOR HVAC PIPING. A. Contents of Division 23, HVAC and Division 01, General Requirements apply to this Section.
SECTION 23 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Gate Valves 2. Balancing Valves 3. Ball Valves 4. Butterfly Valves 5. Swing Check Valves 1.2 RELATED SECTIONS A. Contents of Division
More informationSECTION VALVES PART 1 -GENERAL
SECTION 1571 0 VALVES PART 3- EXECUTION General Shut-off Valves Balancing Valves Drain Valves RELATED WORK Section 15430- Plumbing Specialties Section 15450- Plumbing Equipment PART 1 -GENERAL SCOPE This
More informationDARTMOUTH COLLEGE DESIGN January 3, 2012 & CONSTRUCTION GUIDELINES
SECTION 15100 VALVES PART 1 DESIGN DIRECTIVE 1.1 SUMMARY A. This Section includes general duty valves common to most mechanical piping systems, special duty valves are specified in individual piping system
More informationA. This Section includes general duty valves common to several HVAC piping systems.
SECTION 23 05 23 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More information15100 VALVES. E. Section Building Automation and Control System Guidelines
15100 VALVES PART 1: GENERAL 1.01 RELATED SECTIONS A. Section 15050 Basic Material and Methods B. Section 15545 Chilled Water System C. Section 15550 Heat Generation D. Section 15790 Coils E. Section 15955
More informationA. American National Standards Institute: 1. ANSI Z Relief Valves for Hot Water Supply Systems.
SECTION 220523 - PLUMBING VALVES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Ball valves. 2. Butterfly valves. 3. Swing check valves. 4. Spring loaded check valves. 5. Water pressure reducing
More informationMichigan State University Construction Standards. GENERAL-DUTY VALVES FOR HVAC PIPING Page
Page 230523-1 Copyright 2005 by The American Institute of Architects (AIA) Exclusively published and distributed by Architectural Computer Services, Inc. (ARCOM) for the AIA Modified by MSU Physical Plant
More information1.2 REFERENCES.1 American National Standards Institute (ANSI)/ American Society of Mechanical Engineers (ASME)
Issued 2005/06/01 Section 15111 Valves Bronze Page 1 of 6 PART 1 GENERAL 1.1 RELATED SECTIONS.1 Section 01355 Waste Management and Disposal 1.2 REFERENCES.1 American National Standards Institute (ANSI)/
More informationHenderson Engineers, Inc. SECTION GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS
SECTION 220523 - GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL REQUIREMENTS 1.1 SUMMARY A. This Section includes general duty valves common to most plumbing piping systems. 1. Special purpose
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
PART 1 - GENERAL 1.1 DESCRIPTION OF WORK A. Provide labor, materials, equipment, and services necessary to install valves required to complete the work indicated on drawings. B. ASME Compliance: 1. ASME
More informationSECTION GENERAL-DUTY VALVES FOR HVAC. A. Section includes valves for building services piping.
SECTION 23 05 23 GENERAL-DUTY VALVES FOR HVAC PART 1 - GENERAL 1.1 SUMMARY A. Section includes valves for building services piping. 1.2 REFERENCES A. AGA Z21.22 (American Gas Association) - Relief Valves
More informationVALVES. A. Section HVAC Basic Materials and Methods. E. Section Building Automation and Control System Guidelines
230523 VALVES PART 1: GENERAL 1.01 RELATED SECTIONS A. Section 230500 HVAC Basic Materials and Methods B. Section 230510 Chilled Water System C. Section 230520 Heat Generation D. Section 238216 Coils E.
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SUNY GENESEO 220523-1 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply
More informationUNIVERSITY SERVICES ANNEX James Madison University Harrisonburg, Virginia State Project Code: Architect s Project Number:
SECTION 230523 GENERAL DUTY VALVES FOR HVAC PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Provisions of the Contract and of the Contract Documents apply to this Section. 1.2 DEFINITIONS A. The following
More informationUnion County Vocational - Technical Schools Scotch Plains, New Jersey
SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Iron swing check valves. 3. Iron gate valves. 4. Iron globe valves. B.
More informationSECTION VALVES PART 1 - GENERAL
1.01 RELATED DOCUMENTS SECTION 15100 VALVES PART 1 - GENERAL A. The work in this section includes the furnishing and installation of all control valves and accessories shown on the construction plans and
More informationMichigan State University Construction Standards. GENERAL-DUTY VALVES FOR PLUMBING PIPING Page
Page 220523-1 SECTION 220523 - PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More information***************************************************************************************************************
15515 VALVES, HANGERS, AND SPECIALTIES *************************************************************************************************************** SPECIFIER: CSI MasterFormat 2004 number:23 21 16 ***************************************************************************************************************
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 220523 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division
More informationSECTION FACILITY FUEL OIL PIPING
PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Specification Sections, apply to this Section. B. Related Sections:
More informationHerpteraium SECTION VALVES GENERAL
SECTION 22 05 23 VALVES GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections, apply to
More informationSECTION (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING
SECTION 22 05 23 (15110) - GENERAL DUTY VALVES FOR PLUMBING PIPING PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Valves. B. Related Sections: 1.02 REFERENCES 1. Section 22 05 53 (15075) Identification
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 22 05 23 PART 1 - GENERAL 1.1 SUMMARY A. Work Included: 1. Valves, General 2. Gate Valves 3. Balancing Valves 4. Ball Valves 5. Swing Check Valves 6. Backflow Prevention Assemblies 7. Pressure
More informationA. Valves and specialties including necessary accessories indicated on drawings and specified in this section.
SECTION 15081 - VALVES AND SPECIALTIES (HVAC) PART - 1 - GENERAL 1.01 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 1
More informationBrass, Bronze, Iron and Stainless Steel Valves
Price Schedule June 1, 2011 Supersedes BIV-01-11 07 Brass, Bronze, Iron and Stainless Steel Valves ASTM B283 FORGED BRASS SCREW-IN BONNET NON-RISING STEM SOLID WEDGE DISC 125 WSP/200 WOG BRONZE GATE VALVES
More informationSECTION PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL
SECTION 22 10 10 PLUMBING PIPING VALVES AND ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and
More informationValve Selection. 1. Function and service considerations
1. Function and service considerations Valve Selection Selection Valves serve the purpose of controlling the fluids in building services piping. Valves are produced in a variety of design types and materials.
More informationLCS6822 (Class 150) LCS7822 (Class 300)
Revision 8/22/2012 high performance butterfly valve LCS6822 (Class 150) LCS7822 (Class 300) APPLICATIONS Ideally suited for Commercial, Industrial and Mechanical HVAC Services. Use in other applications
More information1.1 PURPOSE A. This section is intended to define the general installation and minimum product requirements for hydronic and steam valves.
Date Description of Change Pages / Sections Modified ID 6/15/16 Entire document - mgl44 PART 1 - INTRODUCTION 1.1 PURPOSE A. This section is intended to define the general installation and minimum product
More informationA. This Section includes natural gas piping, specialties, and accessories within the building.
SECTION 226313 NATURAL GAS PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
More informationCITY OF TAMPA ADDENDUM 2. July 13, Contract 17-C-00030; David L. Tippin Water Treatment Facility Lime Slaker Replacement
CITY OF TAMPA Bob Buckhorn, Mayor CONTRACT ADMINISTRATION DEPARTMENT Michael W. Chucran, Director ADDENDUM 2 July 13, 2017 Contract 17-C-00030; David L. Tippin Water Treatment Facility Lime Slaker Replacement
More informationHIGH PERFORMANCE BUTTERFLY VALVE
Revised 11/17/2017 HIGH PERFORMANCE BUTTERFLY VALVE LCS-6822 (Class 150) LCS-7822 (Class 300) APPLICATIONS Ideally suited for commercial, industrial, and mechanical HVAC services. Use in other applications
More informationPROJECT TITLE PROJECT NO: CONTRACT TITLE GRANT NO: UNIVERSITY OF CALIFORNIA, DAVIS CITY, CALIFORNIA
The following standard specification is intended to be edited according to the specifics of the project. Brackets [ ] and areas shaded in gray [e.g. format] indicate requirements that are optional depending
More informationSECTION VALVES. A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section.
PART 1 GENERAL 1.01 DESCRIPTION OF WORK SECTION 22412 VALVES A. Extent of Valve Work is indicated on the Drawings and by the Requirements of this Section. B. All valves, except those are 2 in diameter
More informationSECTION VALVES
Buchtel/Perldns Community LearningCenter GPD -2007271.15 SECTION 15110 VALVES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary
More informationCast-Iron Valves G101 DI BUTTERFLY VALVE LEVER... 2 G401 CI GLOBE VALVE CL G403 CI GLOBE VALVE PN G103 DI BUTTERFLY VALVE GEAR...
Cast-Iron Valves PAGE G101 DI BUTTERFLY VALVE LEVER.... 2 PAGE G401 CI GLOBE VALVE CL125.... 9 G103 DI BUTTERFLY VALVE GEAR.... 3 G403 CI GLOBE VALVE PN16.... 10 G201 CI Y STRAINER CL125.... 4 G501 CI
More informationBuildingName The Description of the Project P DOCUMENTS SPECIFICATION DIVISION 22 SECTION DESCRIPTION DIVISION 22 SECTION VALVES
ARCHITECTURE, ENGINEERING AND CONSTRUCTION P00000000 0000 DOCUMENTS ARCHITECTURE & ENGINEERING 326 East Hoover, Mail Stop B Ann Arbor, MI 48109-1002 Phone: 734-764-3414 Fax: 734-936-3334 SPECIFICATION
More informationSECTION COMMON WORK RESULTS FOR FIRE SUPPRESSION. A. Pipe, fittings, valves, and connections for sprinkler systems.
SECTION 210500 - COMMON WORK RESULTS FOR FIRE SUPPRESSION PART 1 GENERAL 1.1 SECTION INCLUDES A. Pipe, fittings, valves, and connections for sprinkler systems. 1.2 RELATED REQUIREMENTS A. Section 099000
More informationLOWER MACUNGIE TOWNSHIP COMMUNITY CENTER ADDITIONS AND RENOVATIONS
LOWER MACUNGIE TOWNSHIP COMMUNITY CENTER. SECTION.0 - GENERAL-DUTY VALVES FOR PLUMBING PIPING PART - GENERAL. RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and
More informationSTANDARDS and SPECIFICATIONS
ANSI (American National Standards Institute) ANSI B31.4 - Liquid petroleum transportation piping system. ANSI B31.4 - Gas transmission and distribution piping system. API (American Petroleum Institute)
More informationSECTION HVAC WATER PIPING ACCESSORIES
SECTION 23 05 10 PART 1 - GENERAL HVAC WATER PIPING ACCESSORIES 1.01 RELATED DOCUMENTS 1.02 SCOPE A. The requirements of the General Conditions, Supplementary Conditions, Division 1, Division 20, and Drawings
More informationTENOCHCA HALL - PROJECT NO FAN COIL UNITS, RESTROOM AND FINISH RENOVATION
SECTION 220523.12 - PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Brass ball valves. 2. Bronze ball valves. 1.2 ACTION SUBMITTALS A. Product Data: For each type of valve. 1. Certification that products
More informationSECTION GENERAL-DUTY VALVES FOR PLUMBING PIPING
SECTION 220523 GENERAL-DUTY VALVES FOR PLUMBING PIPING PART 1 - GENERAL 1.1 SUMMARY A. General: Refer to General and Special Condition Specifications in Division 01 for all required submissions of this
More informationQUALITY YOU CAN BUILD ON CONDENSED CATALOG
QUALITY YOU CAN BUILD ON CONDENSED CATALOG Pressed for time? JUST PRESS, CRIMP AND TRIPLE YOUR PRODUCTIVITY 1. Reduce installation time up to 68% with Hammonds s extensive new line of UltraPress press-connection
More informationcatalog C-NPS-1014 NIBCO Press System
catalog C-NPS-1014 ahead of the flow NIBCO Press System Business-to-Business Solutions Look to NIBCO for technology leadership. The velocity with which e-business evolves demands that new products and
More informationCopyright 2012 AIA MasterSpec Premium 06/12 PRODUCT MASTERSPEC LICENSED BY ARCOM TO CONBRACO, INC.
This Product MasterSpec Section is licensed by ARCOM to Apollo Flow Controls, Conbraco Industries, Inc ("Licensee").This Product MasterSpec Section modifies the original MasterSpec text and does not include
More informationLead-free valves for potable water systems. Rev 02/17
Lead-free valves for potable water systems. Rev 02/17 UltraPure for purer water. The new standard. Senate law S.3874 was passed January 4, 2011 and is effective January 4, 2014. The law regulates lead
More informationIndustrial Bronze and Iron Price List
Industrial Bronze and Iron Price List TABLE OF CONTENTS IND-0217 Effective: February 1, 2017 Revised: 12/07/17 Suggested list prices are subject to change without notification. Visit our Website for the
More informationIndustrial Bronze and Iron Price List
Industrial Bronze and Iron Price List TABLE OF CONTENTS IND-0718 Effective: July 2, 2018 Revised: 08/06/2018 Suggested list prices are subject to change without notification. Visit our Website for the
More informationIndustrial Bronze and Iron Price List
Industrial Bronze and Iron Price List IND-0318 Effective: March 1, 2018 Revised: 08/06/2018 Suggested list prices are subject to change without notification. Visit our Website for the most up-to-date product
More informationIndustrial Bronze and Iron Price List
Industrial Bronze and Iron Price List IND-0718 Effective: July 2, 2018 Revised: 09/24/2018 Suggested list prices are subject to change without notification. Visit our Website for the most up-to-date product
More informationIron Check Valves Illustrated Index
Iron Check Valves Illustrated Index Iron Body Swing Check Valve Bronze Mounted or All Iron 125 lb. SWP 200 lb. CWP Iron Body Swing Check Valve Bronze Mounted 250 lb. SWP 500 lb. CWP Iron Body Silent Check
More informationCopyright 2016 AIA MasterSpec Premium 12/16 PRODUCT MASTERSPEC LICENSED BY ARCOM TO CONBRACO, INC.
This Product MasterSpec Section is licensed by ARCOM to Apollo Flow Controls, Conbraco Industries, Inc ("Licensee").This Product MasterSpec Section modifies the original MasterSpec text and does not include
More informationA. Provide all HVAC specialties required to complete the installation of all HVAC systems. B. Manufacturers: Refer to individual product item.
DIVISION 23 HEATING, VENTILATING, AND AIR CONDITIONING (HVAC) SECTION 23 05 02 PART 1 GENERAL 1.01 DESCRIPTION A. Provide all HVAC specialties required to complete the installation of all HVAC systems.
More informationSECTION (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS
SECTION 22 11 23.13 (15444) - DOMESTIC WATER PACKAGED BOOSTER PUMPS PART 1 GENERAL 1.01 SUMMARY A. Section Includes: 1. Packaged Domestic Water Booster Pumps B. Related Sections: 1.02 REFERENCES 1. Section
More informationUniversity of Houston Master Construction Specifications Insert Project Name
SECTION 23 20 10 - HVAC PIPING VALVES AND ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section
More informationCATALOG C-NPS-0812 AHEAD OF THE FLOW. NIBCO Press System
CATALOG C-NPS-0812 AHEAD OF THE FLOW NIBCO Press System Business-to-Business Solutions Look to NIBCO for technology leadership. The velocity with which e-business evolves demands that new products and
More informationLead-free valves for potable water systems.
Lead-free valves for potable water systems. UltraPure for purer water. The new standard. On January 1, 2010, new laws went into effect that regulate lead content in plumbing products used for potable
More informationBrass, Bronze, Iron and Stainless Steel Valves
Price Schedule June 1, 2015 Supersedes BIV-06-11 CLASS 125 07 Brass, Bronze, Iron and Stainless Steel Valves ASTM B283 FORGED BRASS SCREW-IN BONNET NON-RISING STEM SOLID WEDGE DISC 125 WSP/200 WOG BRONZE
More informationBrass, Bronze, Iron and Stainless Steel Valves
Price Schedule January 1, 2018 Supersedes BIV-06-15 Brass, Bronze, Iron and Stainless Steel Valves 07 BRONZE GATE VALVES CLASS 125 ASTM B283 FORGED BRASS SCREW-IN BONNET NON-RISING STEM SOLID WEDGE DISC
More information1. All piping shall have flow arrows indicating direction of flow.
PART 1: GENERAL 1.01 Scope of Standards A. This design guidelines contained herein includes the requirements for systems, materials, fittings and valves utilized for piping systems at Texas State University.
More informationMercy Hospital of Buffalo Catholic Health System 2 nd Floor Patient Holding Center 3 rd Floor Locker Rooms Shaflucas Architects, PC Project No.
SECTION 23 22 13 STEAM AND CONDENSATE PIPING PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification
More informationPDC Elastomer Lined Series 27 Butterfly Valve 2" thru 36" for 125/150 lb. Flanging
PDC Elastomer Lined Series 27 Butterfly Valve 2" thru 36" for 125/150 lb. Flanging General Description: The PDC "Elastomer Lined" series butterfly valves are available in both full lug and wafer styles.
More informationSize: 1/4 to 3. Material: 316 Stainless Steel, Carbon Steel,
Size: 1/4 to 4 Material: 316 Stainless Steel, Carbon Steel, Alloy 20, Hastelloy C, Monel, Brass, SW, BW, BSPT, 150#, 300#, 600#, Flanged Pressure: Vacuum to 3000 PSI* -50 to 600 F* ASME B16.34 Design Bottom
More informationIndustrial Bronze and Iron Price List
Industrial Bronze and Iron Price List TABLE OF CONTENTS IBI-1017 Effective: October 2, 2017 Revised: 12/07/2017 Suggested list prices are subject to change without notification. Visit our Website for the
More informationUniversity of Houston Master Construction Specifications Insert Project Name SECTION HVAC PIPING VALVES AND ACCESSORIES PART 1 - GENERAL
SECTION 23 20 10 - HVAC PIPING VALVES AND ACCESSORIES PART 1 - GENERAL 1.1 RELATED DOCUMENTS: A. The Conditions of the Contract and applicable requirements of Division 1, "General Requirements", and Section
More informationSECTION STEAM AND STEAM CONDENSATE PIPING. A. ANSI/ASME SEC 9 - Welding and Brazing Qualifications.
SECTION 23 22 00 STEAM AND STEAM CONDENSATE PIPING PART 1 - GENERAL 1.1 SECTION INCLUDES A. Pipe and Pipe Fittings. B. Valves. C. Steam Piping System. D. Steam Condensate Piping System. 1.2 REFERENCES
More informationSee our expanding selection of products on Product Portfolio
See our expanding selection of products on www.fnw.com Product Portfolio Table of Contents Low Lead Products- Page 3 Ball Valves, Check Valves, Strainers, Water Hammer Arrestors Ball Valves, Brass - Page
More informationFigure 1710 Flow Data
AHEAD OF THE FLOW Figure 1710 Flow Data Circuit Balancing Valve Why balance your system? Whether a system is designed for heating or chilling it must be properly adjusted and balanced for optimum design
More information310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve
310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve Features and Benefits Uninterrupted gasket surfaces help eliminate problems associated with seat retaining screws
More informationKEYSTONE FIGURES 310/312 K-LOK BUTTERFLY VALVES
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve FEATURES GENERAL APPLICATION High performance applications such as steam, chill water, water, utility lines, gasoline,
More informationA. This Section includes the following domestic water piping specialties:
SECTION 221119 - DOMESTIC WATER PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes the following domestic water piping specialties: 1. Backflow preventers. 2. Water pressure-reducing
More informationGuide Specification SECTION HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY
SECTION 23 21 16 - HYDRONIC PIPING SPECIALTIES PART 1 - GENERAL 1.1 SUMMARY A. Section Includes: 1. Pressure gages. 2. Pressure gage taps. 3. Thermometers. 4. Thermometer supports. 5. Test plugs. 6. Air
More informationSECTION HYDRONIC PIPING
SECTION 23 21 00 HYDRONIC PIPING PART 1 - GENERAL 1.1 SECTION INCLUDES A. Pipe and Pipe Fittings. B. Valves. C. Heating Water Piping System. D. Glycol Water Piping System. E. Chilled Water Piping System.
More informationKeystone Figures 310/312 K-LOK Butterfly Valves
310 - Wafer high performance butterfly valve 312 - Lugged high performance butterfly valve Features General Application High performance applications such as steam, chill water, water, utility lines, gasoline,
More informationIndex. Butterfly Valves
Dry Bulk - Chemical - Petroleum Dry Bulk - Chemical - Petroleum Nozzles Nozzles & Valves & Index Index Part No. Description Page Nozzles P- 202 Overwing Aircraft Refueling, Bronze 1 P- 2022 Overwing Aircraft
More informationSee our expanding selection of products on Product Portfolio
See our expanding selection of products on www.fnw.com Product Portfolio Table of Contents Low Lead Products- Page 3 Ball Valves, Check Valves, Strainers, Water Hammer Arrestors Ball Valves, Brass - Page
More informationFlow Data for NIBCO Circuit Balancing Valves 1/2 to 2 (Figure Number 1710)
NIBCO INC. WORLD HEADQUARTERS 1516 MIDDLEBURY ST. ELKHART, IN 46516-4740 USA PHONE: 574.295.3000 FAX: 574.295.3307 WEB: www.nibco.com INSTALLATION, OPERATION & MAINTENANCE INSTRUCTIONS Flow Data for NIBCO
More informationCONDENSED CATALOG QUALITY IS MORE THAN WHAT MEETS THE EYE.
CONDENSED CATALOG QUALITY IS MORE THAN WHAT MEETS THE EYE. Pressed for time? JUST PRESS, CRIMP AND TRIPLE YOUR PRODUCTIVITY 1. Reduce installation time up to 68% with Milwaukee Valve s extensive new line
More informationLATEST ARRIVALS CATALOGUE STOCK
LATEST ARRIVALS CATALOGUE STOCK PIPES VALVES FLANGES & FITTINGS IN CARBON STEEL STAINLESS STEEL LATEST ARRIVALS!!!!!! VALVE PRODUCTS CAST IRON WAFER TYPE BUTTERFLY VALVE, PINLESS SHAFT, DUCTILE NICKEL
More informationStandard-Low Emission Valves to 100 PPM. A-Series Brass Appliance Valves CSA Approved; 1 & 2 piece Body Designs; Threaded & Flare End connections
Standard-Low Emission Valves to 100 PPM Cast Steel Valves 150 2500 ASME; Gate, Globe & Check Valves; WCB & High Temperature Chrome Valves; Low Temperature Valves; Flanged, Butt-weld, RTG, End Connections;
More information310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve
310 Wafer high performance butterfly valve 312 Lugged high performance butterfly valve Features and Benefits Uninterrupted gasket surfaces help eliminate problems associated with seat retaining screws
More informationDischarge diameters 1.5", 2", 3", 4", 5", 6", 8", 10", 12" & 14" HP 1 to 500. Split Coupled Vertical In-Line Pumps BVL
Discharge diameters 1.5", 2", 3", 4", 5", 6", 8", 10", 12" & 14" HP 1 to 500 Split Coupled Vertical In-Line Pumps BVL Split Coupled Vertical In-Line Pumps Capacities up to 12,000 GPM Heads up to 560 ft
More informationSECTION MISCELLANEOUS VALVES
SECTION 05140 - PART 1 - GENERAL 1.1 WORK OF THIS SECTION A. The WORK of this Section includes providing miscellaneous valves as indicated, complete and operable, including accessories and operators. 1.2
More informationKVC VALVES AND PEX FITTINGS
KVC VALVES AND PEX FITTINGS 2011 KVC VALVES & PEX FITTINGS CATALOGUE 2 P a g e Table of contents 1. Cast Steel Valves..4 FIG. 272-CS-15 ( Gate ).....5 FIG. 272-CS-300 ( Gate )......6 FIG. 272-CS-600 (
More informationButterfly Valves. watts.com
Butterfly Valves watts.com Durafil is a registered trademark of Cargill, Limited. Teflon is a registered trademark of the E.I. Dupont de Nemours & Company, Incorporated. Uniseal is a registered trademark
More informationFittings. Valves. Actuators
Fittings Valves Actuators Low Emission Valves to 50 PPM Cast Steel Valves 150 2500 ASME; Globe & Check Valves; WCB & High Temperature Chrome Valves; Low Temperature Valves; Flanged, Butt-weld, RTG, End
More informationDeZURIK BOS-CL ON-CENTER, RESILIENT SEATED BUTTERFLY VALVE TECHNICAL SPECIFICATIONS
BULLETIN 46.00-4 MARCH 2015 DeZURIK BOS-CL ON-CENTER, RESILIENT SEATED BUTTERFLY VALVE TECHNICAL SPECIFICATIONS Materials of Construction Item Description Material A1 Body Ductile Iron, ASTM A536, 65-45-12
More informationBOLTED BONNET API 600
PACIFIC VALVES BOLTED BONNET API 600 By Subject Product Overview...2-4 Gate Valves Major Features...5 Gate Valves Optional Features...6 Materials of Construction: Gate Valves...7 Gate Valves Product Line...8-10
More informationCast Iron Valves. Product Information. It s all at Albion
Cast Iron Valves Product Information It s all at Albion ART 77-78 Cast Iron Ball Valve Flanged Ends Flange Mounting PN16 Only ISO 5211 Direct Mount (Not 200mm) Art 77/78 Plated Brass/Stainless Ball BS
More informationA. This Section includes pipe and fitting materials, joining methods, special-duty valves, and specialties for the following:
Page 232113-1 SECTION 232113 PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification Sections,
More informationCNC DISTRIBUTION. ITEM NO Description Quantity
Valves CNC DISTRIBUTION Brass Ball Valves ITEM NO IPS Ball Valve *600# PSI WOG 150 PSI WSP * Heavy Pattern Forged Brass Construction *Full Port For Maximum Flow *Teflon Seats * Teflon Stem Packing * AGA,
More informationPIPING PACKAGES TABLE OF CONTENTS
PIPING PACKAGES TABLE OF CONTENTS ITEM PAGE General Notes and Legend........................................................ 3 Piping Package Code Descriptions & Diagrams VAV Products and HL, HP, VF, and
More informationCAST IRON VALVES CATALOG
CAST IRON VALVES CATALOG www.walworthvalves.com INDEX INTRODUCTION WALWORTH ENGINEERING CONTROL... 5 WALWORTH QUALITY SYSTEM... 5 QUALITY CONTROL EQUIPMENT... 9 CAST IRON GATE, GLOBE & SWING CHECK VALVES
More informationA. This Section includes piping and related specialties for general-service compressed-air systems operating at 150 psig or less.
SECTION 221513 - COMPRESSED-AIR PIPING PART 1 - GENERAL 1.1 SUMMARY A. This Section includes piping and related specialties for general-service compressed-air systems operating at 150 psig or less. 1.2
More informationSECTION METERS AND GAUGES
SECTION 22 05 19 PART 1 GENERAL 1.1 DESCRIPTION OF WORK: A. Extent of meters and gauges required by this section is indicated on drawings and/or specified in other Division-22 sections. B. Types of meters
More informationTOTAL PRODUCT O U R G E N I U S I S V A L V E S & P I P E F I T T I N G S W A T E R H E A T I N G V E N T I L A T I O N A I R C O N G A S
TOTAL PRODUCT C A T A L O G U E W A T E R H E A T I N G V E N T I L A T I O N A I R C O N G A S BALANCING VALVES BALL VALVES BUTTERFLY VALVES CHECK VALVES DRAIN COCKS GATE VALVES GLOBE VALVES PIPE FITTINGS
More information