INFORMATION SHEET: SERIES SxL/SxH DESIGN [] SLIDES IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with slide installation and setup. File with maintenance or machine documentation. TO ORDER SPECIFY: Product, Series, Type, Design No., Bore Size, Travel, and Miscellaneous Options. PRODUCT S - Slide TYPE L-Polymer bushing (see note ) H-Heavy duty precision TC composite bushing BORE (mm) CORROSION RESISTANCE Q6 -Total corrosion resistant guide shafts Z -Total corrosion resistant unit MAGNET M- Magnet for PHD Series 6790 & JC Switches DOWEL HOLES (see availability table below) -Transitional fit J4 - Clearance fit (imperial only) J - Precision fit (metric only) S A L x /2 Z AE M SERIES A- Threaded tool plate B - Counterbore holes in tool plate DESIGN NO. - Imperial - ports and mounting holes are imperial -Metric - ports and mounting holes are metric NOTES: ) L - Polymer bushing not available on size,,, & mm bore units. 2) Shock pads are standard on extend and retract for all sizes. Retract shock pads are located on the guide shafts. Extend shock pad is located internally on the piston. 3) -AE option (stop collars) is recommended for high cycle speed applications and high load applications. Extend shock pads are included with the -AE option to remove impact load from the piston rod. 4) ** Long travel units are available standard on imperial units. 0 mm long travel units are available on metric sizes,, &. Contact PHD for longer travel metric units. DESIGN NO. (IMPERIAL) 2 (METRIC) UNIT & BORE SAL/SBL,, SAH/SBH,,,,, 2, 3, 2, 3, 2, 3 ITEM HOUSING SBx TOOL PLATE HOUSING SBx TOOL PLATE TRAVEL (see note 4) IMPERIAL (in) BASE UNIT ( STD) NONE ( STD) LONG 2, 3, 4 2, 3, 4,, 6 4,, 6, 7, 4,, 6, 7, DOWEL HOLE AVAILABILITY DOWEL HOLES STD STD,, 7,, 7, 7 J4 METRIC (mm) J NOTES: ) SEE DOWEL HOLE DIAMETERS TABLE FOR DIMENSIONAL INFORMATION. 2) STD = Standard = Optional = Production Diameter LONG 0 TRAVEL ADJUSTMENT AE - Extend travel adjustment PHD UNLIMITED A model number ML-xxxxxx indicates the unit is a unique solution. Contact your local distributor or PHD, Inc. for a complete product description.
ENGINEERING DATA: SERIES SxL/SxH DESIGN [] SLIDES SPECIFICATIONS OPERATING PRESSURE OPERATING TEMPERATURE TRAVEL TOLERANCE LUBRICATION MAINTENANCE SERIES SxL / SxH 30 to psi [2 to bar] - to 0 F [-29 to 2 C] Nominal travel +.0/-.000 [+2 mm/-0 mm] Factory lubricated for rated life Field repairable CYLINDER FORCE CALCULATIONS Imperial Metric F = P x A F = 0. x P x A F = Cylinder Force lbs N P = Operating Pressure psi bar A = Effective Area in 2 mm 2 TRAVEL /2 2 /2 /2 2 /2 2 3 /2 2 /2 2 3 4 0 4 0 4 0 SHAFT DIAMETER.97.236 6.394.472 2.0 6.77.94. 30.374 34.9 BORE DIAMETER.3.394..77.94.260.7.969 2.40 EFFECTIVE AREA DIRECTION in 2 mm 2 EXTEND.07.3 RETRACT.0 37.4 EXTEND.22 7.7 RETRACT.09.7 EXTEND.23 4 RETRACT.9 26 EXTEND.47 3 RETRACT.9 264 EXTEND.76 49 RETRACT.9 42 EXTEND.247 0 RETRACT.07 69 EXTEND.94 6. RETRACT.6. EXTEND 3.043 9.2 RETRACT 2.6 649.0 EXTEND 4. 37.4 RETRACT 4.34 203.2 BASE WEIGHT lb kg.24..29.3.34..2.3.36.6.44..2.6..79.36.9.43...2.9.9 2.23 2..72.7 2.26.03 2.0.27 3.3 3. 4.42 4.9. 2.79.27 3.62.64 4.4 2.02.2 6. 6.92 7.7. 3.9.76 4.97 2. 6.0 2.74 7.3.2 9.2.. 6..7 3.6.2 4.64.99.4 3.70.4 7.2.3.9 3.43 6..92 7.2.4.34.90 23.39. 2.3 7.2.64 9.34 24.03.7 27.4 2.4 30.79 34. 37..9 MAX. STATIC LOAD SxL SxH lb N lb N 46 33 7 26 6 60 267 2 36 44 96 9 262 34 46 3 2 2 2 934 344 30 90 4 4 30 667 2 9 6 23 9 69 20 24 37 6 90 4 260 6 667 9 33 0 9 423 2 73 4 49 6 49 276 3 37 30 69 32 26 229 2 0 2 2349 94 23 26 9 4226 230 3336 60 44 393 32 94 7 77 374 62 36 3 96 43 74 67 2 29 277 222 99 447 62 22 2 3 323 30 69 3 3 2964 3 42 222 97 7 TYPICAL DYNAMIC LOAD lb N 0-0 - 4. - 2 4. -.9 2-6.9-26.7 6-2 26.7-3.4-6 44. - 7.2 2-3.4-6 - 7 7-334 - 0-44 7-334 - 66 2
ENGINEERING DATA & IONS: SERIES SxL/SxH DESIGN [] SLIDES MATERIAL SPECIFICATIONS On both the Series SxL and SxH units, the slide housing and tool plate are anodized aluminum alloy. SERIES SxL SLIDES On Series SxL Slides sizes,,,, and, the guide shafts are hard chrome plated steel. The -Q6 corrosion resistant option these sizes provides hard chrome plated stainless steel guide shafts. All Series SxL Slides have low friction polymer bearings. SERIES SxH SLIDES Series SxH Slides have precision ground case hardened guide shafts. The -Q6 corrosion resistant option provides a corrosion resistant coating on these guide shafts. Series SxH Slides utilize high load capacity composite bearings. MOUNTING TORQUE SLIDE BODY THREADED MOUNTING -AE ION COLLAR CLAMP SCREW -AE ION THREADED MOUNTING PART DESCRIPTION Collar Clamp Screw (-AE option) Female Thread on Bottom of Body Thread on SAx Tool Plate Imperial Unit Metric Unit Imperial Unit Metric Unit SAxx 22 [2.] [.] [.7] [.] [.] SAxx 22 [2.] 2 [3.2] [4.] [.6] [.7] SAxx [.6] 64 [7.2] 7 [.] 2 [3.2] [4.] SAxx 0 [.3] [6.9] [3.6] 64 [7.2] 7 [.] TORQUE in-lb [Nm] SAxx SAxx 0 [.3] [6.9] 0 [2.2] 300 [33.9] 27 [3.] 27 [3.] [6.9] [6.9] [3.6] [3.6] Sxxx 3 [39.] 3 [39.] 430 [4.6] 300 [33.9] 27 [3.] Sxxx 3 [39.] 4 [.] 0 [6.] 4 [.] 0 [6.] Sxxx 700 [79.] 7 [4.7] 700 [79.] 00 [3.0] 700 [79.] AE TRAVEL ADJUSTMENT ON EXTEND This option provides both travel adjustment stop collars and shock pads on extension only. The travel adjustment stop collars provide infinite adjustment while the shock pads provide excellent noise reduction and energy absorption capability. NOTE: AE travel adjustments are available as a kit. To specify, give the full unit description -H903. Each travel adjustment kit contains 2 steel shaft collars, 2 shock pads, and 2 SHCS..0 [6.0].2 [6.0] ONLY.6 [6.].2 [3.0] A B SHOCK PAD SHCS C D SHAFT COLLAR UNIT UNIT A B C D.064 [.6].064 [.6].3 [.0].709.064 [.6]. [3.2].99 [.0].99 [.0].0 [6.4].0 [6.4].0 [6.4].433 [.0]. [3.0]. [3.0].90 [.0].7 [.0].749 [9.0].66 [22.0].7..37.0 2.026 2.34 2.7.37 [9.].0 [2.7].9 [.0].6 [22.0].94 [24.0]. [2.6].0 [3.].7 [44.] 2. [3.] LETTER DIMENSION [mm] TRAVEL ADJUSTMENT KIT [.0] [22.2] [2.6] [34.9] [3.] [.] [9.6] [69.9] KIT NUMBER COLLAR SCREWS Z ION MAX TORQUE 73439-734- 7344-73442- 7422-73443- 796-797- 79-73439-2 734-2 7344-2 73442-7422-2 73443-2 796-2 797-2 79-2 22 in/lb 22 in/lb in/lb 0 in/lb 0 in/lb in/lb 3 in/lb 3 in/lb 700 in/lb [2. Nm] [2. Nm] [.6 Nm] [.3 Nm] [.3 Nm] [6.9 Nm] [39. Nm] [39. Nm] [79. Nm] 3
IONS: SERIES SxL/SxH DESIGN [] SLIDES TRANSITIONAL FIT M MAGNET FOR PHD SERIES 6790 & JC SWITCHES Transitional fit dowel pin holes in the tool plate and housing provides a compromise fit between clearance and interference. Transitional fits are used where accuracy of location is important, but a small amount of clearance in order to simplify the installation of dowel pins is permissible. J4 Clearance fit dowel pin holes in the tool plate and housing are used when extra clearance is needed due to inaccuracies of attached tooling. Available on imperial units only. J CLEARANCE FIT H7 tolerance precision fit dowel pin holes in the tool plate and housing are used where accuracy of location is of prime importance Ideal for parts requiring rigidity and alignment. Metric units only. Q6 PRECISION FIT Stainless steel hard chrome guide shafts on the Series SxL Slides and corrosion resistant coating on the Series SxH Slides for use in applications where moisture may corrode untreated, hardened and ground shafts. For sizes and locations, see dimension pages. Z TOTAL CORROSION RESISTANT GUIDE SHAFTS TOTAL CORROSION RESISTANT UNIT This option equips the unit with a magnetic piston for use with PHD s Series 6790 and JC Switches. The switch housing is completely contained by the slide housing and provides a very compact switch design. The switches mount easily to the slide housing using two small grooves located on the top of the unit and are locked into place with a set screw. See Switches and Sensors section of Main Catalog for additional switch information and complete specifications. SERIES 6790 & JCSDX CORDSET CHART PART NO. DESCRIPTION 49-02 M, 3 pin, Straight Female Connector, 2 m cable 49-0 M, 3 pin, Straight Female Connector, m cable TORQUE CHART SWITCH TORQUE 6790 6 in-oz JCSDx Hand tighten clockwise until switch is securely retained. Do not overtighten. SERIES 6790 & JC SWITCHES PART NO. DESCRIPTION 67902--0 PNP (Source) or NPN (Sink) Reed, 4.-30 VDC, m cable JCSDN- NPN (Sink) Solid State, -30 VDC, m cable JCSDP- PNP (Source) Solid State, -30 VDC, m cable 67922- PNP (Source) or NPN (Sink) Reed, 4.-30 VDC, Quick Connect JCSDN-K NPN (Sink) Solid State, -30 VDC, Quick Connect JCSDP-K PNP (Source) Solid State, -30 VDC, Quick Connect 67929-2 PNP (Source) or NPN (Sink) Reed, 6- VAC, Quick Connect This option includes Q6 guide shafts and provides stainless steel or electroless nickel plating on all other externally exposed ferrous parts. This optional plating can be used for protecting the slide from severe or corrosive environments. START-UP PROCEDURES Slide should be securely mounted with all tooling and external flow control devices attached prior to applying pressure to the unit. Care should be taken to provide adequate clearance for the tool plate and guideshafts to extend and retract. At initial start-up, apply pressure slowly to the unit. 4
EXPLODED VIEW & PARTS LIST: SERIES SxL/SxH DESIGN [] SLIDES KEY PART DESCRIPTION HOUSING ASSEMBLY FULL UNIT DESCRIPTION REQUIRED -H400 2 PISTON & ROD ASSEMBLY FULL UNIT DESCRIPTION REQUIRED -H00 3 PISTON SEAL SOLD AS PART OF SEAL KIT 4 ROD SEAL SOLD AS PART OF SEAL KIT GUIDE SHAFT FULL UNIT DESCRIPTION REQUIRED -H47 6 CARTRIDGE / CAP SEAL SOLD AS PART OF SEAL KIT 7 CAP 7247 72497 77 727 746 737 79647 7967 79667 TOOL PLATE FULL UNIT DESCRIPTION REQUIRED -H60 9 CARTRIDGE / CAP RETAINER FULL UNIT DESCRIPTION REQUIRED -H70 INTERNAL SHOCK PAD 6093 63 64 743 74 379 7964 796 7966 EXTERNAL SHOCK PAD 63 64 6069 6730 742 74 79642 7962 79662 2 TOOL PLATE TO GUIDE SHAFT SCREWS FULL UNIT DESCRIPTION REQUIRED -H47 3 CARTRIDGE 7246 72496 76 726 74 736 79646 7966 79666 TOOL PLATE TO PISTON ROD SCREW FULL UNIT DESCRIPTION REQUIRED -H3600 IONAL PARTS 9 COLLAR SHOCK PAD SOLD AS PART OF TRAVEL ADJUST ASSEMBLY 2 SHCS KITS KIT DESCRIPTION SEAL KIT FULL UNIT DESCRIPTION REQUIRED -H9000 EXTEND TRAVEL ADJUSTMENT KIT FULL UNIT DESCRIPTION REQUIRED -H903 (2 COLLARS, 2 SCREWS, AND 2 SHOCK PADS PER KIT) SxL GUIDE SHAFT BEARING KIT FULL UNIT DESCRIPTION REQUIRED -H34 (4 BEARINGS PER KIT - NOT AVAILABLE FOR SxH) 2 9 6 7 9 3 4 3 2 9 6 2