SERIES BCZ2D NOZZLE CYLINDER START-UP AND INFORMATION SHEET
|
|
- Jeffery Walton
- 6 years ago
- Views:
Transcription
1 Model Number Definition SERIES BCZD NOZZLE CYLINDER START-UP AND INFORMATION SHEET IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with cylinder installation, setup and repair. File with maintenance or machine documentation. TO ORDER, SPECIFY: Product, Series, Type, Machine No., Process, Design No., Bore Size, Stroke Configurations, and any Options. PRODUCT B - Blow Mold TYPE Z - Nozzle MACHINE NO. - Series BORE SIZE 0 mm STROKE CONFIGURATION STD STROKE mm (cold set only) mm (heat set only) FITTING OPTIONS* L0 - Straight port fitting installed for mm tubing L0-90ϒ swivel elbow port fitting installed for mm tubing B C Z S x - U - L0 SERIES C - Cylinder PROCESS S-CSD D-Heat Set DESIGN NO. - Metric MC U VALVE OPTIONS* - Manifold circuit only for MAC 00 valve - Attached MAC 00 valve ) Consult PHD for additional options such as magnetic piston, ISO/valve manifold combinations and alternative MAC 00 valve combinations. ) *If no fittings or valves are required, leave blank. Life Expectancy Series BCZ Cylinders have been designed for million trouble-free cycles except for high pressure stretch rod seal. Long life stretch rod seal provides times longer life than previous Series BCZ seals tested in a lab environment. Operation with lubricated air can extend cylinder life. Cycle Rate Series BCZ Nozzle Cylinders meet or exceed cycle rate of competitor s unit when using optional manifold/valve combinations. Maintenance As with most PHD products, these cylinders are field repairable. Repair kits, tooling kits, and main structural components are available as needed for extended service. Optional rebuild service is available. LUBRICATION Series BCZ Nozzle Cylinders are lubricated with FDA approved food grade lube which provides extended life and better performance. For maximum life, PHD recommends lubricating all seals which come in contact with the stretch rod every months with FDA food grade lubrication. As machine set-ups and conditions vary, PHD Inc. cannot guarantee the same extended life will be seen as that resulting from PHD s own lab testing of the stretch rod seal. CYLINDER SPECIFICATIONS TYPE SERIES CYLINDER BORE SIZE DIAMETER CYLINDER - LOW URE BORE AREA - EXTEND BORE AREA - RETRACT THEORETICAL EXTEND OUTPUT THEORETICAL RETRACT OUTPUT OPERATION OPERATING URE RANGE BLOW CYLINDER - HIGH URE BORE SIZE BORE AREA OPERATING URE THEORETICAL CLAMP FORCE AMBIENT & FLUID TEMPERATURE STROKE TIME (TYPICAL) FULL RETRACT TO MID POSITION MID POSITION TO FULL EXTEND FULL EXTEND TO MID POSITION MID POSITION TO FULL RETRACT LUBRICATION PORT SIZE STROKE For additional technical assistance, call: BCZD IMPERIAL METRIC Pneumatic BCZ Heat Set Nozzle Cylinder.9 in 0 mm.96 in 0 mm.6 in. cm.0 in 9. cm 06 psi 96 6 bar 6 psi 6 6 bar Double Acting. - 0 psi bar.6 in mm. in. cm 600 psi. bar psi 9 bar -0 to 0 F -9 to C ms ms ms 90 ms FDA Regulation CFR 9.0 G/.69 in ( ) mm ( ) P.O. Box 900, Fort Wayne, IN
2 DISASSEMBLY PROCEDURES: SERIES BCZD PHD, Inc. makes no warranty as to the fitness of its products or as to the length of service life after being repaired or parts replaced by anyone other than authorized employees of PHD, Inc. In no event shall PHD, Inc. be liable for loss of profits, indirect, consequential, or incidental damages arising out of the use of PHD Products. DISASSEMBLY PROCEDURE ) WARNING: All air pressure in the unit must be exhausted prior to disassembly of nozzle cylinder. ) During disassembly, be careful to avoid scratching or damaging sealing surfaces. A non-metallic screwdriver (6) is included with each repair kit to help prevent damage while removing low pressure piston and rod seals. ) A pick type tool is suggested for removal of high pressure seals. (Figure ) ) Remove nozzle and locking nut from piston rod. ) Using 6mm hex wrench, remove all SHCS from tube and cap. Notice that the tube screws are longer than the cap screws. (Figure ) 6) Using of the SHCS just removed, thread screws into the threaded holes in the tube. Tightening these SHCS will separate tube from the body. (Figure ) ) Separate tube from body and remove piston rod from assembly. (Figure ) ) Remove cap from tube. (Figure ) 9) Remove retaining ring from cap. (Figure ) 0) Using a small flat blade screwdriver (not included), pry rod wiper out of the cap. (Figure 6) ) Remove rod and cap seal from cap. (Figure ) ) Using small diameter of tool and arbor press, press bushing out of cap. (Figure ) ) Using a small screwdriver, remove snap ring from the body. (Figure 9) ) Pry large rod seal from body using tool 6. (Figure 9) ) Using small diameter of tool 09 and arbor press, press bushing out of body. (Figure 0) 6) Using spanner wrench 6 and a vise, separate P & R assembly into three components. (Figure ) Note: Place the P&R into a vise and clamp onto the flats on the front piston. Figure (Longer Screws) Insert tool 6 into the end of the smaller piston locating the dowels into the hole in the end. Using an aluminum or steel bar in diameter and approximately long (not supplied), slide it through the hole in the spanner wrench tool 6 to aid in the disassembly. Once the smaller P&R is loosened from the larger P&R it may be possible to use a /' drive breaker bar to complete the disassembly. ) Remove wear ring, shock pads and all seals from piston rods. (Figure ) ) To remove high pressure piston seals, use pick tool (not included) to lift up under the seals and cut seals using a pair of side cutters. 9) Using long side of tool 0 and arbor press, press bushing out of intermediate piston. (Figure ) 0) The repair kit provides new components for wear items to completely rebuild unit. Unless a fastener kit was also purchased, keep all SHCS to repair unit. Discard all old seals, shock pads and bushings and clean all remaining parts. X SHCS Figure Figure Figure Figure Figure 6 ROD WIPER X SHCS SEPARATE, ROD & ASSEMBLIES RETAINING RING Figure Figure ARBOR Figure 9 Figure 0 SNAP RING SEAL 09 FLANGE OR SLEEVE 6 Figure SEPARATE P&R BY USING APPROPRIATE S 00 IN-LB MINIMUM TORQUE REQUIRED Figure 0 PLACE WRENCH FLATS IN A VISE PER 6 PISTON Figure DISCARD ALL OF THE PARTS LABELED X PISTON SEALS ( 6) X PISTON SEAL (PICK ) WEAR RING ( 6) X S (PICK ) Figure PICK OR EQUIVALENT 6 X SHOCK PADS X HIGH URE PISTON SEALS NOT INCLUDED
3 ASSEMBLY PROCEDURES: SERIES BCZD PHD, Inc. makes no warranty as to the fitness of its products or as to the length of service life after being repaired or parts replaced by anyone other than authorized employees of PHD, Inc. In no event shall PHD, Inc. be liable for loss of profits, indirect, consequential, or incidental damages arising out of the use of PHD Products. ASSEMBLY PROCEDURE ) All seals and wear surfaces must be lubricated with FDA food grade lubrication prior to assembly. Recommended lubricant is provided in repair kit. ) PHD recommends using adhesive primer and thread locker for all threaded interfaces. ) Press bushing into intermediate piston using short side of tool 0. (Figure ) ) Place piston seals onto intermediate piston noting seal lip orientation. (Figure ) ) Press shock pads onto intermediate piston. (Figure ) 6) Place high pressure piston seals onto high pressure piston rod noting lip orientation. (Figure 6) ) Press shock pad into low pressure piston rod. (Figure 6) ) Slide tool over the threads on the high pressure piston rod and slip intermediate piston assembly onto the high pressure piston rod. (Figure ) 9) Place wrench flats on the low pressure piston assembly into a vise and thread high pressure piston assembly into low pressure piston assembly. Using recommended primer and adhesive, torque to 00 in-lb [90 Nm] using spanner wrench tool 6. (Figure ) 0) Using large diameter of tool 09 and arbor press, press bushing with chamfered side down into body until seated by tool depth. (Figure 9) ) Install rod seal into body with part number of seal located on outside of body. (Figure 0) ) Install retaining ring into body by separating coils and working retaining ring in a circle around groove. (Figure 0) NOTE: Replacement kits contain two different seals and bushings for the cap. Replace the seal and bushing with those that were removed. The other seal and bushing may be discarded. ) Using large diameter of tool and arbor press, install cap bushing until seated by tool depth. (Figure ) ) Install rod seal into cap using tool 06 and 0 with orientation as shown. (Figure ) ) Place o-ring onto cap. (Figure ) 6) Using tool 09 and an arbor press, press rod wiper into cap until fully seated. (Figure ) ) Install retaining ring into cap by separating coils and working retaining ring in a circle around groove. (Figure ) ) Place o-ring onto tube. (Figure ) 9) Place o-ring onto low pressure piston rod assembly. (Figure ) 0) Wrap wear ring around the high pressure piston and while holding wear ring ends, slip tube over high pressure piston rod assembly. (Figure ) ) Place shock pad onto low pressure piston rod assembly (Figure ) ) Work body over low pressure seals and seat body fully against tube aligning all flat sides. (Figure 6) ) Using recommended thread locker, torque tube screws to 00 in-lb [ Nm]. (Figure ) ) Work cap assembly onto tube until fully seated. (Figure ) ) Using recommended thread locker, torque cap screws to 00 in-lb [ Nm]. (Figure ) Figure Figure SHOCK PADS 0 X ROD SEALS Figure 6 X PISTON HIGH URE Figure SEALS INTERMEDIATE PISTON ASSEMBLY HIGH URE PISTON X PISTON SEALS LOW URE SHOCK PAD X HIGH URE PISTON SEALS Figure HIGH URE Figure 9 Figure 0 RETAINING RING Figure Figure ASSEMBLY 09 LOW URE INTERMEDIATE ASSEMBLY PISTON ASSEMBLY 6 INSTALL WITH PART NO. ON OUTSIDE SLEEVE OR FLANGE SEAL DETAIL KIT Figure Figure Figure WEAR RING 09 ROD WIPER SHOCK PAD ORIENTATION Figure 6 STRETCH LUBRICATION PROCEDURES: With stretch rod installed:. Fully extend the stretch rod.. Apply a / inch wide ring of lubricant around the outside diameter of the stretch rod just below the blow nozzle bell.. Fully retract the stretch rod.. Once again, fully extend the stretch rod once and wipe away the excess lube from it. With stretch rod removed:. With a small brush or similar device, apply a small amount of lubricant to inside surface of the stretch rod seal(s).
4 EXPLODED VIEW: SERIES BCZD FILL GREASE RESERVOIR.09 ±.0 DETAIL E DETAIL B B DETAIL C C D DETAIL D E F DETAIL F OPTIONAL FITTINGS CROSS-SECTION PORT POSITION DETAIL PORT LOCATION DETAIL ) NUMBERS INCLUDED IN A HEX INDICATE PORT POSITION ) NUMBERS INCLUDED IN AN OVAL INDICATE PORT LOCATION 6 E F F 9 A 6 SEAL GROOVE B I.D. D E C F D B D D D D6 G THREAD I.D. H A 0 B C D D D D SEAL GROOVE = HYDRAULIC SEALANT & PRIMER KIT [0] GROOVES D = THREAD LOCKER C B I.D. A PISTON BORE = -0 (HIGH URE FOOD GRADE GREASE) = -0, 0 (LOW URE FOOD GRADE GREASE) M x..9 [6] Kit provides a rod locking nut made of steel with yellow zinc dichromate plating.
5 PARTS LIST: SERIES BCZD KEY A B C D A B C D D D D D D D6 E F G H A B C D E F PART DESCRIPTION Body Assembly Double Stage Body Rod Seal Retaining Ring Piston and Rod Assembly Double Stage Cylinder Piston & Rod Piston Seal Intermediate Piston Assembly Piston Rod Seal Piston Seal Double Stage Cylinder Piston & Rod High Pressure Piston Seal Wear Ring Rod O-Ring Double Stage Tube Cap Assembly Cap Rod Wiper Rod Seal Cap O-Ring Retaining Ring Tube O-Ring Cap Screw Tube Screws High Pressure Fitting Plug Manifold Plate Assembly Manifold O-Ring Manifold Screw Muffler Label MAC 00 Series Valve Valve Manifold O-Ring mm Tube Fitting (-L0) mm Tube Fitting (-L0) mm Tube Fitting (-L0-U OR -L0-MC) mm Tube Fitting (-L0-U OR -L0-MC) Valve Screw PTF Port Plug Proximity Flag Orifice Disk BCZD--0x Full unit description required followed by -H Full unit description required followed by -H000 0 Full unit description required followed by -H Full unit description required followed by -H00 69 Sold as part of Fastener Kit -H900 Sold as part of Fastener Kit -H MAC A-BOA-DM-DDAJ- JM = Sold As Part of Orifice Kit or Manifold Kit KIT DESCRIPTION Unit Repair Kit Rod Locking Nut Tooling Kit Cap Seal Tooling Kit Fastener Kit Manifold Kit Cap Repair Kit Stretch Rod Seal Repair Kit Orifice Kit KIT NUMBER Full unit description required followed by -H Full unit description required followed by -H ) Includes all parts to repair the full unit excluding cap parts. ) Includes all hardware to completely repair cap. ) Includes all specialized tools required to rebuild unit. ) For maximum life, PHD recommends lubricating all seals which come in contact with the stretch rod every months with the following lubrication: FDA Food Grade Lubrication. As machine set-ups and conditions vary, PHD Inc. cannot guarantee the same extended life will be seen as that resulting from PHD s own lab testing of the stretch rod seal. ) Includes tools to rebuild cap. Tools in this kit are also included in Kit #. PHD, Inc., P.O. Box 900, Fort Wayne, IN (60) -6 Fax (60) -6
SERIES1 NOZZLE CYLINDER REPAIR PROCEDURES
THE FOLLOWING REPAIR PROCEDURE ENCOMPASSES THESE PHD ML UNITS : - ML309435, ML310142, ML310153, ML310254, ML310295, ML310427, 1) Refer to individual ML exploded view for actual part numbers. 2) Not all
More informationPPC PRODUCTS PARTS LISTS CATALOG 2013
PLASTIC PACKAGING COMPONENTS GROUP PPC PRODUCTS PARTS LISTS CATALOG 0 Quality Delivery Support SOLUTIONS A division of PHD PPCPARTS INDEX Page FACTORY REBUILD PROGRAM Using H Codes... Cylinders STRETCH
More informationREBUILD PROCEDURES: SERIES BCZUS UNIVERSAL NOZZLE CYLINDER DISASSEMBLY OF CYLINDER REBUILD / REASSEMBLY
PHD, Inc. makes no warranty as to the fitness of its products or as to the length of service life after being repaired or parts replaced by anyone other than authorized employees of PHD, Inc. In no event
More informationSTRAIGHT FITTING ORIFICE DISK MUFFLER MANIFOLD MOUNTING PLATE MULTI-FUNCTION IMPACT SEAL CYLINDER TUBE 1/4 BSPP ELBOW FITTING HEAD ASSEMBLY
Disassembly OF THE CYLINDER 1) WARNING: All air pressure in the unit must be exhausted prior to disassembly of stretch rod cylinder. 2) Remove valve from manifold (valve not shown). 3) Remove mufflers,
More informationSTRETCH ROD CYLINDERS for Krones Stretch Blow Molding Machines
PACKAGING COMPONENTS PLASTIC GROUP BCK STRETCH ROD CYLINDERS for Krones Stretch Blow Molding Machines Quality Delivery Support SOLUTIONS A division of PHD Simplified Pneumatic System Easy Maintenance Better
More informationINFORMATION SHEET: SERIES GRT 3 JAW PARALLEL GRIPPERS
INFORMATION SHEET: SERIES GRT 3 JAW PARALLEL GRIPPERS IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with gripper installation and setup. File with maintenance or machine documentation.
More informationKRONES DIRECT REPLACEMENTS
PLASTIC PACKAGING COMPONENTS GRO Quality Support Delivery SOLUTIONS A BLOW division MOLDING SOLUTIONS of PHD PLASTIC PACKAGING COMPONENTS P KRONES DIRECT REPLACEMENTS phdinc.com (800) 624-8511 INCREASE
More informationDIRECT REPLACEMENTS. phdinc.com (800) INCREASE PRODUCTION REDUCE MAINTENANCE REDUCE DOWNTIME REDUCE SCRAP STRETCHING CYLINDERS
SOLUTIONS A BLOW division MOLDING SOLUTIONS of PHD P Quality SIDEL Support Delivery PLASTIC PACKAGING COMPONENTS P ASTIC PACKAGING COMPONENTS GRO DIRECT REPLACEMENTS phdinc.com (800) 624-8511 INCREASE
More informationSERIES BCS STRETCH ROD CYLINDERS
BCS y Q ua lit Support SOLUTIONS for the Plastic Bottle Blowing Industry DIRECT REPLACEMENT FOR SIDEL SERIES AND SERIES MACHINES P U O C PACK TI A S y er iv el D ENTS GR N O G COM P IN G SERIES BCS STRETCH
More informationParts online Spare parts list
Parts online Spare parts list Refer to the Parts online web page for most up to date information. The printed information might be outdated. Contents Service, repair and wear part kits Kit list 1 Mechanical
More informationPSP SERIES PSP SHOT PIN. Superior part locating and positioning. Provides the best repeatability in its class. Patent Pending PSP01A
PSP SERIES PSP SHOT PIN Superior part locating and positioning. Provides the best repeatability in its class. Port Fittings Option Switch Options Weld Cover Option Patent Pending ORDERING DATA: SERIES
More informationSachs shock manual. ( ) 2 & 4 Stroke RR Enduro. ( ) RS Dual Sport
Sachs shock manual (2013 2015) 2 & 4 Stroke RR Enduro (2014-2015) RS Dual Sport 1 Introduction The procedures in this manual must take place in a clean environment using professional tools and some specific,
More informationDisassembly Instructions hp. Dynafile II Models: 40352, 40353
Disassembly Instructions - 0.4 hp. Dynafile II Models: 40352, 40353 Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever
More informationREPAIR PROCEDURES MANUAL
REPAIR PROCEDURES MANUAL PVX Series Vane Pumps A Design Series Step-by-Step Guide to Troubleshooting and Repairing PVX Series Vane Pumps Introduction Thank you for choosing Continental Hydraulics PVX Vane
More informationSERVICE PARTS LIST SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS 1" D-HANDLE ROTARY HAMMER SERIAL NUMBER G43A See page 6.
00 0 CATALOG NO. EXAMPLE: Component Parts (Small #) Are Included When Ordering The Assembly (Large #). = Component of the 14-4-525 522-21 Maintenance Service Kit SEE PAGE TWO FOR THE PROCEDURE ON CHECKING
More informationBack Pressure Regulator
Instruction Sheet P/N 108652H Description The Nordson back pressure regulator is a spring-loaded, hand-operated fluid pressure regulator designed for use with general liquid coating materials. The regulator
More informationSERIES SCV SLIDES DESIGN 2/6 INFORMATION SHEET
SERIES SC SLIDES DESIGN / INFORMATION SHEET IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with slide installation and setup. File with maintenance or machine documentation.
More informationDisassembly Instructions hp. Mini-Dynafile II
Disassembly Instructions - 0.4 hp. Mini-Dynafile II Important: Use these instructions along with the tool parts page or manual. Notice: Shut off the air supply and depress throttle lever to deplete the
More informationSERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS
SERVICE INSTRUCTIONS FOR SEAL REPLACEMENT OF POWER GEAR HYDRAULIC LEVELING LEGS 82-L0352 REV 8 4-27-2011 WARNING! HYDRAULIC COMPONENTS CAN CAUSE SERIOUS INJURY OR DEATH IF PROPER SAFETY PRECAUTIONS ARE
More informationSpare parts list. Hydraulic breakers RX 30.
Spare parts list Hydraulic breakers RX 30 RX 30 Valid from serial number DEQ121453 Valid to serial number www.cp.com RX 30 Spare parts list General information This spare parts list applies to the following:
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 5 in. (127 mm) and 6 in. (150 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20347, 3M Overhaul Service Kit, contains all the replacement parts
More informationIntroduction. Pressed Shaft Flowmeter. Flowmeter Service Kits. Disassembly. Idler Shaft Removal
Flowmeter Service Kits Introduction See Figure. This instruction sheet provides repair procedures for flowmeters that use either pressed or screw-in shafts. Refer to the applicable repair procedure: Pressed
More informationSERIES SFP SLIDES INFORMATION SHEET. Ordering Data. U.S. Patent No. 6,857,780 International Patent No. CA PART NO.
Ordering Data SERIES SFP SLIDES INFORMATION SHEET IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with slide installation and setup. File with maintenance or machine documentation.
More informationLOR Series Trig-O-Matic Lite Overload Release Clutch
LOR Series Trig-O-Matic Lite Overload Release Clutch P-3029-BG LOR Series Installation and Operation An Altra Industrial Motion Company Contents I. Introduction A. Operating Principle... 3 B. Torque Adjustment...
More informationIso-Flo Coupling Repair
Instruction Sheet P/N 229782C Iso-Flo Coupling Repair Introduction This instruction sheet covers the repair of the male and female couplings used in the Automatic and Manual Iso-Flo HD Voltage Block Systems,
More informationSpare parts list. Hydraulic breakers RX 26.
Spare parts list Hydraulic breakers RX 26 RX 26 Valid from serial number DEQ152263 Valid to serial number www.cp.com RX 26 Spare parts list General information This spare parts list applies to the following:
More informationINSTALLATION INSTRUCTIONS South Highway 11 Westminster, SC Toll Free (888) (864) FAX (864)
These instructions apply to the servicing of the Lift Technologies MaxiMizer Integral Sideshifters Cylinder Head. WARNING! Unless the steps in the following Installation Instructions are properly followed
More informationCylinder Maintenance & Repair Instructions
Cylinder Maintenance & Repair Instructions PENINSULAR CYLINDER CO. Model HP High Pressure Hydraulic Cylinders Proximity Switch & Non Proximity Switch Designs - High Pressure NFPA Hydraulic Cylinder ( 5,000
More informationOverhaul Special Tools Required
1 of 31 Overhaul - Special Tools Required - Cylinder end seal remover attachment, 07NAD-SR3020A - Pilot collar, 07GAF-PH70100 - Valve seal ring sizing tool, 07NAG-SR3090A - Ball joint boot clip guide,
More informationSpare parts list. Hydraulic breakers RX Valid from serial number
Hydraulic breakers Valid from serial number 50 www.cp.com Contents Contents General information............................................................... 5....................................................................
More information3M Overhaul Service Kit
SERVICE INSTRUCTIONS FOR 3M 12,000 RPM 3 in. (77 mm) RANDOM ORBITAL SANDERS 3M Overhaul Service Kit The part number 20346, 3M Overhaul Service Kit, contains all the replacement parts that naturally wear
More informationShock Absorber for Formula Student and Formula SAE TTX 25. Workshop Manual
Shock Absorber for Formula Student and Formula SAE TTX 5 Workshop Manual SAFETY PRECAUTIONS General Warnings Note! The shock absorber is an important part of the vehicle and will affect the stability.
More informationHard Seat Fluid Pressure Regulator
Instruction Sheet P/N 04742-02 Description The Nordson hard seat fluid pressure regulator is designed for use with abrasive coatings. The regulator body is constructed of stainless steel with a nickel-plated
More informationIdeal for robotic and end effector applications
MINIATURE CLAMPS FOR WORKHOLDING APPLICATIONS Ideal for robotic and end effector applications Bayonet Body Option -B11 ORDERING DATA: SERIES GRM CLAMP SIZE 1 INDEX: Ordering Data Page 2 Benefits Page 3
More informationProportioning pumps and hydraulic cylinders used on Hydraulic Proportioners. Model : 2000 psi (13.8 MPa, 138 bar) Maximum Working Pressure
- Parts Proportioning Pumps 3068F Proportioning pumps and hydraulic cylinders used on Hydraulic Proportioners. Important Safety Instructions Read all warnings and instructions in this manual and in manuals
More information0-800 psi Carbide Seat Fluid Pressure Regulator
Instruction Sheet P/N 0350C 0-800 psi Carbide Seat Fluid Pressure Regulator Description The Nordson 0-800 psi carbide seat fluid pressure regulator is designed for use with general liquid coatings. The
More informationSpare parts list. Hydraulic breakers RX Valid from serial number
Hydraulic breakers Valid from serial number 50 www.cp.com Contents Contents General information............................................................... 5....................................................................
More information3. Park vehicle on a clean, dry, flat, level surface and block the tires so the vehicle cannot roll in either direction.
InstalL Instructions ram assist single-ended ram rebuild kit 304201-kit 304202-kit (for 1.5" bore x 3/4" rod rams with 6" or 8" stroke) (for 2" bore x 3/4" rod rams with 6" or 8" stroke) kit contents 304202-ins
More informationGRA GRV SERIES GRA PARALLEL GRIPPERS SERIES GRV ANGULAR GRIPPERS. Compact Precision Grippers Ideal for a Wide Range of Applications
GRA GRV SERIES GRA PARALLEL GRIPPERS SERIES GRV ANGULAR GRIPPERS Compact Precision Grippers Ideal for a Wide Range of Applications Series GRA Parallel Series GRV Angular GRAV0 ORDERING DATA: SERIES GRA
More informationARM OVER CLAMP FOR ASSEMBLY AND WELDING
ARM OVER CLAMP FOR ASSEMBLY AND WELDING Superior part holding Provides widest range of high clamping force in its class OPTIONS: AD001 AU001 AL001 AR000 SW42 PS1E1 Patent Pending ORDERING DATA: SERIES
More informationIdeal for part clamping in weld areas
PIN LOCATING CLAMPS FOR THE AUTOMOBILE INDUSTRY Series PLK Ideal for part clamping in weld areas Completely enclosed finger/pin prevents weld slag from entering Locking mechanism holds panel in place if
More informationTECHNICAL SERVICE MANUAL
Electronic copies of the most current TSM issue can be found on the Viking Pump website at www.vikingpump.com TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES
More informationFront Hub and Disc (4WD Model)
4C 8 DRIVE SHAFT SYSTEM Disassembled View Front Hub and Disc (4WD Model) 411RW001 Legend (1) Bolt (2) Cap (3) Snap Ring and Shim (4) Hub Flange (5) Lock Washer and Lock Screw (6) Hub Nut (7) Outer Bearing
More informationMaintenance Information
45530136 Edition 1 July 2008 Electric Screwdrivers EL 24V DC Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this tool.
More informationINFORMATION SHEET: SERIES SxL/SxH DESIGN 1 [5] SLIDES
INFORMATION SHEET: SERIES SxL/SxH DESIGN [] SLIDES IMPORTANT INFORMATION DO NOT DISCARD! Use this information sheet to assist with slide installation and setup. File with maintenance or machine documentation.
More informationIdeal for robotic and end effector applications
MINIATURE CLAMPS FOR WORKHOLDING APPLICATIONS Ideal for robotic and end effector applications Bayonet Body Option -B11 ORDERING DATA: SERIES GRM CLAMP SIZE 1 INDEX: Ordering Data Page 2 Benefits Page 3
More informationFOR PART CLAMPING IN WELD AREAS
PLk SERIES PLK PIN LOCATING CLAMP for the Automotive Industry IDEAL FOR PART CLAMPING IN WELD AREAS Enclosed Finger Weld Field Immune Switches PLK01 A ORDERING DATA: SERIES PLK CLAMPS INDEX: Ordering Data
More informationInput Adjusting Ring Leak Repair Procedure for Meritor MT-14X Series Forward Differential Carriers
Revised 01-16 Technical Bulletin Input Adjusting Ring Leak Repair Procedure for Meritor MT-14X Series Forward Differential Carriers Revised 1 Technical 01- Bulletin 16 Hazard Alert Messages Read and observe
More informationPLK/PLKD SERIES PLK/PLKD PIN LOCATING CLAMPS
PLK/PLKD SERIES PLK/PLKD PIN LOCATING CLAMPS Ideal for part clamping in weld areas Disappearing Pin Weld Field Immune Switch PLK03 PLK/PLKD PIN LOCATING CLAMPS PATENT PENDING Major Benefits Completely
More informationSoft Seat Fluid Pressure Regulator
Instruction Sheet P/N 04622F Description The Nordson soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel with a
More informationFig Variable Speed Valve Parts
5 DISASSEMBLY OF VARIABLE SPEED CONTROL VALVE (Seal Replacement with Control Valve in the Bobcat). Remove seat and seat plate (Fig. ).. Remove variable speed control lever linkage rod. 3. Remove temperature
More informationMaverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.2 SHOCK SERVICE MANUAL
Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.2 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.2 rear shock is an oil damped
More informationBoston Gear LOR Series
Boston Gear LOR Series Trig-O-Matic Lite Overload Release Clutch Installation and Maintenance Instructions Doc. No. LOR Series Trig-O-Matic Lite www.bostongear.com LOR SERIES TRIG-O-MATIC LITE OVERLOAD
More informationParallel Grippers- DPW DIRECTCONNECT Wide Body Series
DPW SERIES 1.196 Parallel Grippers- DPW DIRECTCONNECT Wide Body Series DIRECTCONNECT Connectivity: DIRECTCONNECT Tapped and Dowel mounting on body. Large or Wide Parts: Wide body design provides secure
More informationGRB. long life Compact Angular gripper SHIPS IN 1-2 days. Major Benefits. Industry Uses
long life Compact Angular gripper SHIPS IN 1-2 days hardened steel jaws have robust design and include dowel holes for precise tooling location steel cover, jaw design, and tight jaw slots minimize external
More informationMaverick American 3085 Bluff Street Boulder, CO Tel: Fax: ML7.0 SHOCK SERVICE MANUAL
Maverick American 3085 Bluff Street Boulder, CO 80301 Tel: 303-415-0370 Fax: 303-415-0676 www.maverickamerican.com ML7.0 SHOCK SERVICE MANUAL 1. OVERVIEW 1.1. The Maverick ML7.0 rear shock is an oil damped
More informationParallel Grippers- DPDS DIRECTCONNECT Modular Series
Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (8) 426-548 www.cmafh.com 1.134 Parallel Grippers- DPDS DIRECTCONNECT Modular Series Mounting Information: Grippers
More informationfile://c:\program Files\tsocache\OFFICE_5416\SY1~us~en~file=SY131B46.htm~gen~ref...
Page 1 of 41 SECTION 303-01B: Engine 4.6L and 5.4L 2000 F-150 Workshop Manual ASSEMBLY Procedure revision date: 01/27/2004 Engine 4.6L Special Tool(s) Compressor, Valve Spring 303-567 (T97P-6565-AH) Compressor
More informationSC series Stopper Cylinders
SERIES 60,000 PSI tensile strength electro-less nickel rod bearing High strength threaded connection Hard chrome plated 100,000 PSI yield strength rod inc plated dust cover series Stopper Cylinders Common
More informationHYDRAULICS. TX420 & & lower. Hydraulic Tandem Pump Removal. 4. Remove the LH side panel (Fig. 0388).
TX420 & 425 240000299 & lower 4. Remove the LH side panel (Fig. 0388). Hydraulic Tandem Pump Removal Note: Cleanliness is a key factor in a successful repair of any hydraulic system. Thoroughly clean all
More informationSC series Stopper Cylinders
High strength threaded connection Low friction cup sealintegral rod wiper Double wound 302 SS retaining wire 60,000 PSI tensile strength electro-less nickel rod bearing Low friction figure 8 piston seal
More informationrings used in the TuckAway Electric Monitor (#3352)
STYLE 3352 O-Ring Ring Replacement Guide The following tools & materials are required for disassembly & servicing of the O-rings rings used in the (#3352) 5/64 Allen wrench 7/64 Allen wrench* 3/16 Allen
More informationJARVIS. Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner. 30CL-1 Hock Cutter
Model 30CL-1 AND 30CL-3 Hock Cutter and Dehorner 30CL-1 Hock Cutter with Leg Grabber 30CL-1 Hock Cutter 30CL-3 Dehorner Equipment Selection 30CL-1 Sheep Head Dropper Order Number 30CL-1 Hock Cutter 30CL-1
More informationINTEGRAL POWER STEERING GEAR FORD Applies to F-100 F-350 (4X2), F-150 F-250 (4X4) And Bronco
Rockcrawler Steering Shop Manual page1 The following is from the Ford 1978 Truck Shop Manual, Volume 1 Chassis. It is provided here as a courtesy to classic Ford owners who would like to perform their
More informationTECHNICAL GUIDE. For TOUGH GARD Spatter Cleaner GENERAL SAFETY INSTALLATION MAINTENANCE TECHNICAL DATA ORDERING INFORMATION
TECHNICAL GUIDE For TOUGH GARD Spatter Cleaner GENERAL SAFETY INSTALLATION MAINTENANCE TECHNICAL DATA ORDERING INFORMATION Certified ISO 9001:2008 Please read instructions prior to use. Save this manual
More informationgrme SERIES GRME ELECTRIC CLAMP Electric Clamp with Greater Flexibility & Durability for the Automotive Industry GRME01A
grme SERIES GRME ELECTRIC CLAMP for the Automotive Industry Electric Clamp with Greater Flexibility & Durability GRME1A ORDERING DATA: SERIES GRME ELECTRIC CLAMPS INDEX: Ordering Data Pages 2 and 3 Benefits
More informationPNEUMATIC 180 ANGULAR GRIPPER
PNEUMATIC 180 ANGULAR GRIPPER Major Benefits Jaws rotate completely clear of work area eliminating an otherwise required axis of travel Three standard jaw rotations available: 60, 90, and 180 One piece
More informationDisassembly / Reassembly Procedure
08-T059 Disassembly / Reassembly Procedure HEAVY DUTY TYPE PNEUMATIC CYLINDER 10A-3 SERIES Failure to observe the instructions given in this manual could cause this equipment
More informationGRM SERIES GRM CLAMPS R JAW STYLE. Compact Jaw Profi le for Limited Space Applications Largest Total Clamp Force of All Series GRM2 Clamps GRMR01
GRM SERIES GRM CLAMPS R STYLE Compact Jaw Profi le for Limited Space Applications Largest Total Clamp Force of All Series GRM2 Clamps ORDERING DATA: SERIES GRM CLAMP STYLE R INDEX: Ordering Data Page 2
More informationSERIES PA SWING ARM CLAMPS for the Automotive Industry
Pa SERIES PA SWING ARM CLAMPS for the Automotive Industry Ideal for a wide variety of automated part holding and transfer applications Copper Arm Switches Installed ORDERING DATA: SERIES PA CLAMPS INDEX:
More informationSM64155 Maintenance & Repair Manual
SM64155 September 2011 Applicable addition manuals: Aerospace Group Conveyance Systems Division Carter Brand SM61429 Nozzle SM64349 Nozzle SM64201 Nozzle Maintenance & Repair Manual Continuity Dry Break
More informationPOR SERIES Pneumatic Overload Release Clutches
POR SERIES Pneumatic Overload Release Clutches P-3030-BG Installation and Operation POR Series Model H2000 An Altra Industrial Motion Company Contents I. Operating Principle...2 Il. Ill. Mounting Adapters
More informationCONTENTS. VIKING PUMP, INC. A Unit of IDEX Corporation Cedar Falls, IA USA SECTION TSM 710.1
TECHNICAL SERVICE MANUAL industrial heavy duty motor speed pumps SERIES 4076 AND 4176 SIZES hle, ate and ale SECTION TSM 710.1 PAGE 1 of 8 ISSUE B CONTENTS Introduction....................... 1 Safety
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationMaintenance Information
Form 16573321 Edition 1 July 2004 Air Grinder Series 61H Maintenance Information Save These Instructions Always wear eye protection when operating or performing maintenance on this tool. Always turn off
More informationSTEERING SYSTEM 6 A POWER STEERING
STEERING SYSTEM 6 A 22147 POWER STEERING Table of Contents Page Specifications............................ 6A-1 Torque Specification................... 6A-1 Special Tools............................ 6A-1
More informationEC 150T. Spare parts list. Hydraulic breakers. EC 150T s/n DEQ Construction Tools GmbH No
EC 150T Spare parts list Hydraulic breakers EC 150T s/n DEQ181223-2018 Construction Tools GmbH No. 3390768001 2018-07-30 General information This spare parts list applies to the following: Part number
More informationMaintenance Information
16573321 Edition 3 February 2014 Air Grinder Series 61H Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings, and to avoid these
More information0-500 PSI Soft Seat Fluid Pressure Regulator
Instruction Sheet P/N 0953A Description The Nordson 0-500 psi soft seat fluid pressure regulator is designed for use with nonabrasive liquid coatings. The regulator body is constructed of stainless steel
More informationVALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT INSTRUCTIONS SMC 84Q & 2408 LOADERS NEW HOLLAND TRACTORS MODEL 2WD 4WD LESS CAB WITH CAB 1720 X X X 1920 X X X TRACTOR AND VALVE KIT GENERAL
More informationSMS Solid Stainless Cylinders
SMS Solid Stainless Cylinders Space Saving and Conventional Lengths Pneumatic to 200 PSI Hydraulic 400 to 500 PSI Non shock /8,, 2, 3 Bore 300 Series Stainless Exterior Assures Aesthetics and Function
More informationHigh-Torque, Easy Speed & Stroke Control, Field Adaptable
D R I V I N G T H E I N D U S T R Y F O R W A R D High-Torque, Easy Speed & Stroke Control, Field Adaptable Fully Adjustable Stroke Length and Jaw Stop Positions Flow Controls Fitted as Standard Quick
More informationService Manual for Hydraulic Cylinder
Electric Drives and Controls Service Manual for Hydraulic Cylinder Model CDT1/CGT1 Hydraulics Linear Motion and Assembly Technologies Pneumatics Service Table of contents Seal Replacement General 2 Old
More informationVALVE AND PLUMBING KIT 2409 LOADER CUB CADET & KIOTI TRACTORS
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT 2409 LOADER CUB CADET & KIOTI TRACTORS TRACTOR MODELS CUB CADET 8404, 8454 KIOTI DK45, DK50 ROPS X X TRACTOR AND VALVE KIT GENERAL INFORMATION
More informationPOWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly
POWER STEERING PUMP REBUILDING SPK101 Read instructions completely before removal & disassembly DISASSEMBLY: 1. Remove pump from car and allow to drain. 2. Remove pulley from front of pump. This requires
More informationPneumatic Cylinder 14 Bore X 22 Stroke Part No. R (Formerly P )
Pneumatic Cylinder 14 Bore X 22 Stroke Part No. R434001268 (Formerly P -193419-00003) Service Information INSTALLATION Before installing this cylinder, all air lines in the system should be blown clean
More informationTable of Contents. B. Base Utility Coupler...B-4 G2x/G5x Series Utility Couplers with Integrated Compliance...B-4 1. Product Overview...
Table of Contents B. Base Utility Coupler...B-4 G2x/G5x Series Utility Couplers with Integrated Compliance...B-4 1. Product Overview...B-4 1.1 G2x/G5x Compliant Utility Coupler Master... B-5 1.2 G2x/G5x
More informationMaintenance Information
45528270 Edition 1 June 2007 Barring Motor T480 Series Maintenance Information Save These Instructions WARNING Always wear eye protection when operating or performing maintenance on this Barring Motor.
More informationEngine. Special Tool(s) Compressor, Valve Spring (T97P-6565-AH) Compressor Spacer, Valve Spring (T91P-6565-AH)
Page 1 of 41 SECTION 303-01A: Engine 5.4L (2V) 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual ASSEMBLY Procedure revision date: 04/04/2003 Engine Special Tool(s) Compressor,
More informationJARVIS. Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner
Model 30CL-1 and 30CL-3 Hock Cutter and Dehorner 30CL--1 Hock Cutter 30CL--1 Pistol Grip 30CL--3 Dehorner EQUIPMENT SELECTION... Ordering No. 30CL--1 Hock Cutter... 4025013 30CL--1 Hock Cutter with Grabber
More informationEngine. Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent. Compressor, Valve Spring (T93P-6565-AR)
SECTION 303-01C: Engine 5.4L (4V) 2009 Mustang Workshop Manual ASSEMBLY Procedure revision date: 12/12/2008 Engine Special Tool(s) Compressor, Piston Ring 303-D032 (D81L-6002-C) or equivalent Compressor,
More informationHydraulics. Part B, Section 1. This section covers the following unit configurations. 3700V 3800V 3900V
Part B, Section 1 Model Voltage Pump Manifold Control This section covers the following unit configurations. 3500V 3700V 3800V 3900V All Piston (F) 4-Port (A) 6-Port (B or C) -Port (S or T) Vista Standard
More informationTRIM AND TILT TABLE OF CONTENTS TRIM AND TILT
TRIM AND TILT TABLE OF CONTENTS SERVICE CHART................................................................... 326 SYSTEM DESCRIPTION............................................................. 328
More informationService Kit
Service Kit 753-05607 Date: Subject: Models Affected: April 17, 2009 (Revised 6/08/2009) Hydraulic Cylinder Seal Replacement XINGHUI 4.5 Cylinder 718-0769A Read through and understand these instructions
More informationFULL COLOR TAB #6 TC 105
FULL COLOR TAB #6 TC 105 SERIES TC 2-STAGE TELESCOPING CYLINDER CONSTRUCTION FEATURES 3 Bore Sizes: 0.75, 1.50 and 2.50 Strokes up to 60 2-Stage Telescoping Space Saving Design 100% Double Action Heavy-Duty
More informationSERVICE GUIDE 8540-B 8549-B C. High-Pressure Lubricant Pump DESCRIPTION. Pump Assembly. Specifications
SERVICE GUIDE 8540-B 8549-B1 8549-C DESCRIPTION The major components of the high-pressure pump models in this series consist of a(n): air-operated motor lubricant pressure controller (pressurtrol) double-acting
More informationVALVE AND PLUMBING KIT NEW HOLLAND 7310 LOADER NEW HOLLAND TRACTORS
ASSEMBLY MANUAL Keep With Operator s Manual VALVE AND PLUMBING KIT NEW HOLLAND 73 LOADER NEW HOLLAND TRACTORS MODEL 2WD FWA LESS CAB WITH CAB TT55 X X X TT75 X X X Valve and plumbing kit can be installed
More informationMaintenance Information
04581245 Edition 2 May 2014 Air Grinder, Die Grinder and Sander Series G2 (Angle) Maintenance Information Save These Instructions Product Safety Information WARNING Failure to observe the following warnings,
More informationAirHawk Gauge and Alarm Assembly
AirHawk Gauge and Alarm Assembly MAINTENANCE AND REPAIR MSA 511 (L) Rev. 4 MSA 2015 Prnt. Spec. 10000005389 (I) Mat. 10079636 Doc. 10079636 AIRHAWK GAUGE AND ALARM ASSEMBLY AIRHAWK GAUGE AND ALARM COMPONENTS
More informationParallel Grippers- Two Jaw Precision Spring Series
Courtesy of CMA/Flodyne/Hydradyne Motion Control Hydraulic Pneumatic Electrical Mechanical (8) 426-548 www.cmafh.com 1.186 TM Parallel Grippers- Two Jaw Precision Spring Series Mounting Information: Grippers
More information