ngular Grippers NGULR GRIPPERS 2.1
ngular Motion Gripper Product Overview NGULR GRIPPERS 2.2 RU Series ngular Gripper 2-Jaw ngular Gripper Spring ssist Pneumatic or Hydraulic Operation Preferred Market: l Global Page 2. DCT/CT Series TM 18 ngular Gripper 18 of travel (Optional djustable Stop) Features DIRECTCONNECT mounting (sizes 12-25) Sealed design protects internal components from chips and other particulate Optional Resistive or Inductive Sensors Page 2.32 Vulcan Series Hi-Temp ngular Gripper ir Top or Lateral Blowing Port Optional Kelvar Boot, metal seals, or stainless heat shield Optional stainless steel jaws and hardware Preferred Market: s N u S R Series Cam Driven Gripper R-5 & 6 DESIGN DVNTGES Inexpensive djustable stroke Rugged design R-1 DESIGN DVNTGES Extremely small (1in.) and lightweight (1 oz.) Inexpensive Preferred Market: l Global Page 2.16 Page 2.22 Preferred Market: l Global DCT-RE/CT-RE Series 18 Failsafe ngular Gripper 18 of travel (Optional djustable Stop) Spring ssist Features DIRECTCONNECT mounting (sizes 12-25) Sealed design protects internal components from chips and other particulate Optional Magneto Resistive or Inductive Sensors Preferred Market: l Global FU Series Food Gripper Designed for direct product contact in the food zone, according to the food industry standard (EN 1672-2) ll parts are corrosion resistant, non-toxic, non-contaminating, non-porous, non-absorbent and non-reactive Stainless steel design resists chemical cleaning procedures TM Page 2. Page 2.56 Preferred Market: l Global
Destaco-Robohand ngular Gripper Product Selector Two Jaws Three Jaws 12 Degrees 3 Degrees 7 Degrees 18 Degrees 1-1 lbs. [.5-5Kg] 1-25 lbs. [5-111Kg] 25-5 lbs. [111-223Kg] 5-1 lbs. [223-5Kg] 1-5 lbs. [5-2225Kg] 5-3 lbs. [2225-1335Kg] - 2 in. [ - 5.8mm] 2 - in. [5.8-12mm] - 6 in. [12-152mm] 6-8 in. [152-23mm] 8-1 in. [23-25mm] 1-12 in. [25-35mm] 12-1 in. [35-356mm] 1-16 in. [356-6mm] 16-18 in. [6-57mm] 18-2 in. [57-58mm] 2 in.+ [58mm+].5 -.1 sec..1 -.5 sec..5 -.75 sec..75-1 sec. 5-1 psi [.3-7 bar] 2-1 psi [1.5-7 bar] - 1 psi [3-7 bar] 5-1 psi [3.5-7 bar] 7-15 psi [5-7 bar] Clean Room Environment Normal Environment Harsh/Dirty Environment Failsafe Operation Inductive Sensors Magneto Resistive Sensors Double cting Cylinder Single cting/spring Return Double cting/spring ssist Non-Synchronous Option Total Grip Maximum Finger Length ctuation Operating Environ- Model # Stroke Range Force Range @ 6 PSI [ bar] Time Pressure ment CYLINDRICL DESIGN RU-62 RU-82 RU-112 RU-12 RU-162 NGULR GRIPPERS 2.3 HI-TEMP DESIGN VULCN-112 VULCN-12 VULCN-162 CM DRIVEN DESIGN R-5 R-6 R-1 18 DESIGN DCT-12 DCT-16 DCT-2 DCT-25 CT-32 CT- CT-5 18 FILSFE DESIGN DCT-12-RE DCT-16-RE DCT-2-RE DCT-25-RE CT-32-RE CT--RE CT-5-RE FOOD GRIPPER DESIGN FU-63
ngular Grippers- High Power Series RU SERIES 2. Cost effective: The simplified drive mechanism makes these grippers an excellent value Compact, robust & powerful gripper: This gripper is designed for use in confined spaces, combining large opening angle with a high torque. Optional safety springs retain the components, should the air supply fail or to increase grip force. Multipurpose gripper: wide range of options and accessories (hydraulic or pneumatic operation, safety springs for internal or external clamping, Viton seals, and magneto resistive or inductive sensing) allow these grippers to be used in a number of applications. Harsh environment: Shielded design repels chips and other particulate from internal drive mechanism High Temperature Design (Vulcan Series): Designed for heavy-duty, extreme high temperature applications, the Vulcan Series Gripper can be ordered with optional metal seals and fireproof kevlar boot or stainless steel heat shield for added protection. Mounting Information: Gripper can be mounted and operated in any orientation Gripper is located using pilot boss and a dowel pin and assembled with through body screws. G Gripper can be operated utilizing top manifold air ports. Fingers are located on jaws with 2 dowel pins and assembled with 1 screw. Technical Specifications: Specifications Imperial Metric Pneumatic Pressure Operating Range: Standard 3-1 psi 2-7 bar with -RE, -RI Spring Option 5-1 psi 3-7 bar Hydraulic Pressure Operating Range:** Hydraulic 3-29 psi 2-2 bar with -RE, -RI Spring Option 5-29 psi Cylinder Type 3-2 bar Double cting or Single cting Spring Return or Double cting Spring ssist Dynamic Seals Internally Lubricated Buna-N Valve Required -way, 2-position for Double cting to Operate or 3-way, 2-position for Single cting ir Quality Requirements ir Filtration Micron or Better ir Lubrication Not Necessary* ir Humidity Low Moisture Content (dry) Temperature Operating Range Viton Seals (RU Series) -2 ~3 F -3 ~15 C Vulcan Series -2 ~82 F -3 ~5 C Maintenance Specifications Expected Life Normal pplication 5 million cycles w/ Preventative Maintenance 1+ million cycles* Field Repairable Yes Seal Repair Kits vailable Yes *ddition of lubrication will greatly increase service life Maintenance Section ** The gripper can be operated at 29psi (2 bars) MXIMUM hydraulic pressure. Cycle times are longer and may depend on the hydraulic system. Grippers must be mounted before being operated under hydraulic pressure. Please contact factory for more information.
Quality Components Made of luminum alloy, hard coat anodized with Teflon Impregnation. The gripper s main components are made of heat treated steel. Viton Seals Standard Viton seals for high temperatures (-2 F to +3 F / -3 ~15 C) Hi-Temp Design Designed for extreme high temperature applications up to 82 F [5 C] (Vulcan Series only) Safety Springs Optional springs retain the component, should the air supply fail, to assist the gripper for internal (-RI) or external (-RE) gripping, or in single acting or spring assist mode Pivot Pin Product Features Gripper ttachment From the top or from the back using DirectConnect pattern (except sizes 12M & 162M). Magneto Resistive Sensing The gripper comes with adjustable slots for 2 magnetic sensors. (to control jaw position). Must be used with -RE or -RI option. (Except sizes 12M & 162M) Operating Principle Shielded Case Shielded Case and Covers Gripper is shielded to repel chips and other particulate from internal drive mechanism. Hydraulic Operation Optional hydraulic seals for 29 psi [2 bar] Max. operation Multiple Ports Side or top manifold ports Integrated Inductive Sensor n integrated sensor (KT1 or KT2 option) allows to sense jaws in open or closed position Jaw Style -RU ngular Gripper Size -62M Style: RU-62M Stroke: 33.6 Grip Force:* 86 lbs 38 N Weight:.86 lbs.39 Kg Page 2.6 *Grip force @ 1PSI [7 bar], L=1" [25.], with spring, jaws at º Style -RU ngular Gripper Size -82M Style: RU-82M Stroke: 31.8 Grip Force:* 276 lbs 1228 N Weight: 1.5 lbs.7 Kg Page 2.8 *Grip force @ 1PSI [7 bar], L=1" [25.], with spring, jaws at º Style -RU ngular Gripper Size -112M Style: RU-112M Stroke: 38.2 Grip Force:* 83 lbs 215 N Weight: 3.75 lbs 1.7 Kg Page 2.1 *Grip force @ 1PSI [7 bar], L=1" [25.], with spring, jaws at º Style -RU ngular Gripper Size -12M Style: RU-12M Stroke: 35.2 Grip Force:* 1298 lbs 5775 N Weight: 9.5 lbs.1 Kg Page 2.12 *Grip force @ 1PSI [7 bar], L=1" [25.], with spring, jaws at º RU SERIES 2.5 Style -RU ngular Gripper Body Cam Lever Size -162M Style: RU-162M Stroke: 3. Grip Force:* 1778 lbs 7911 N Weight: 1.8 lbs 6.7 Kg Page 2.1 Piston *Grip force @ 1PSI [7 bar], L=1" [25.], with spring, jaws at º Cam Driver Groove Cap Spring Style -VULCN ngular Gripper Size -112M Style: VULCN-112M Stroke: 38. Grip Force:* 895 lbs 3983 N Weight: 3.75 lbs 1.7 Kg Page 2.16 *Grip force @ 1PSI [7 bar], L=1" [25.], with spring, jaws at º Pressure Exhaust Exhaust Pressure double acting piston, connected to a cam driver with a groove, drives the cams levers. The piston s translatory motion makes the cams levers rotate in a synchronous motion. Optional springs can be used to increase the grip force, to hold part in the event of loss of air, or to use the gripper in single acting mode. This gripper is suitable for internal or external gripping. Style -VULCN ngular Gripper Size -12M Style: VULCN-12M Stroke: 35.2 Grip Force:* 133 lbs 5975 N Weight: 9. lbs.1 Kg Page 2.17 *Grip force @ 1PSI [7 bar], L=2" [5.8], with spring, jaws at º Style -VULCN ngular Gripper Size -162M Style: VULCN-162M Stroke: 3.6 Grip Force:* 215 lbs 896 N Weight: 1.77 lbs 6.7 Kg Page 2.18 *Grip force @ 1PSI [7 bar], L=2" [5.8], with spring, jaws at º
NGULR GRIPPER RU-62M SPRING SSISTED SERIES RU SERIES 2.6 2 Open Purge port [5.8] Ø 2. [.5] x Ø.177 3 5 Close Manifold air port Supplied plugged [ 5 H9 x 13 DP] Ø.1969 SF x.512 1..39 2..95 6..236 Purge / Scavenge port [ M5 x 6 ] 2.6.12 53. 2.87 35. 1.378 37.5 1.76 21.5.86 16..63 6. Ø 2.362 [ 38.1 h7 ] Ø 1.5 SF 3..118 2 [G1/8 x 5 DP] [3 h7] Ø.1181 SF [ M5 x 7 DP] 13..512 13..5118 19..78 [1 f8].3937 2 Close 2 Open 8. 1.89 -KT: Inductive sensor Opened: 13 76. 2.992 Sensing range (From close position) Yellow LED Green LED KT1 to 3. 13. to 16.8 KT2 to 6.8 1 to 16.8 Inductive sensor Closed: 3.9 71. 2.795 Same attachment as gripper UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] How to Order: (Order Separately) BSIC MODEL RU-62M - - - POWER P H POWER P-Pneumatic H-Hydraulic Pneumatic Hydraulic (2 bar max.) SPRING RE Closed RI Open Leave Blank. No Spring Option (standard) SPRING SSIST ( Below) INDUCTIVE CSE* KT1 Sensing Range KT1 KT2 Sensing Range KT2 Leave Blank. No Inductive Option * Inductive Case not available with DU model INTEGRTED SENSOR SMPLE ORDER: RU-62M-P-RI-KT1 Ex: RU-62M Gripper, Pneumatic, Spring Open, Sensing Range KT1 SENSOR CCESSORIES ORDER # QTY/UNIT PNP Magneto Resistive Sensor w/qk Disconnect* ** OHSP-17 1 or 2 NPN Magneto Resistive Sensor w/qk Disconnect* ** OHSN-17 1 or 2 PNP Magneto Resistive Sensor (9 Barrel) w/qk Disc* ** OHSP-11 1 or 2 NPN Magneto Resistive Sensor (9 Barrel) w/qk Disc* ** OHSN-11 1 or 2 Replacement PNP Double Inductive Sensor* *** KT15 1 Quick Disconnect 2 Meter Cable* CBL-1 1 or 2 Quick Disconnect 5 Meter Cable* CBL-13 1 or 2 Quick Disconnect 2 Meter Cable (for KT15 Inductive Sensor)* CBL-1 1 or 2 SELED BOOT KITS PVC Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-367 1 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-368 1 FireProof Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-369 1 SEL REPIR KIT PNEUMTIC HYDRULIC Viton Seal Repair Kit SLKT-156V SLKT-33V 1 *Sensor and cable sold separately Requires Mounting Kit **Piston magnet standard Not compatible with Hydraulic (-H) option and requires -RE or -RI option ***Requires KT1 or KT2 Inductive Case Option
NGULR GRIPPER RU-62M SPRING SSISTED SERIES Specifications RU-62M Total Rated Grip Force L=1 in [25.mm] @ 1 psi, 7 bar, w/spring... 86 lbs. 38 N 1 psi, 7 bar, w/o spring... 7 lbs. 313 N Stroke... 16.8 of stroke for each finger Weight....86 lbs..39 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 5-1 psi 3-7 bar Cylinder Bore Ø... 1.57 in. mm Displacement....73 in 3. 12 cm 3 Temperature Range Viton Seals Standard... -2 ~3 F -3~15 C ctuation (open/close)....18 sec./.18 sec. ccuracy... ±.2 in. ±.5 mm Repeatability... ±.8 mm. ±.2 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position FINGER FORCE - F/2 N lbs. 15 337 125 281 1 225 75 169 5 112 25 56 1 PSI [7 bar] PSI [ bar].5 1. 1.5 2. 2.5 3. 3.5 in. 12.7 25. 38.1 5.8 63.5 76.2 88.9 mm L GRIP FORCE PER FINGER (at with Spring ssist) 29 PSI [ 2 bar] 8 PSI [5.5 bar] EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L Y 6 PSI [.1 bar] C T Mx X WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/2 F/2 Loading Capacity Static Dynamic Maximum Tensile T 53 lbs. [236 N] 11 lbs. [7.2 N] Maximum Compressive C 53 lbs. [236 N] 11 lbs. [7.2 N] Maximum Moment Mx 111 in.-lbs. [12.5 Nm] 27 in.-lbs. [3.1 Nm] Maximum Moment My 35 in.-lbs. [3.5 Nm] 31 in.-lbs. [3.5 Nm] Maximum Moment Mz 111 in.-lbs. [12.5 Nm] 27 in.-lbs. [3.1 Nm] Capacities are per set of jaws and are not simultaneous My RU SERIES 2.7 ccessory Mounting Technical Data 1.212 3.8.715 18.2.73 19.728 18.5.185.7.117 3 OHSP/N 17 OHSP/N 11 MR Sensors PNP and NPN Magneto Resistive available Sensors are slot mounted, no mounting kits required Simple adjustment with slotted screw driver Built in LED for ease of positioning and troubleshooting vailable with 2M or 5M Quick Disconnect mating cable (order separately).51 13 PLUMBING FITTING PLFT-38 Plumbing Fittings djustable flow controls: Have thumb screw adjust with locking nut for adjusting actuation time vailable for 6mm OD tubing Plumbing fittings: For side air port location Top airport are plugged as standard DJUSTBLE FLOW CONTROL G1/8 VLVF-5 dapter plate for cover set up Clamping Crown Ø 3.268 83 2.138.5 11.3 5.3 Boot Protects the gripper mechanism Provides better performance and longer life time in harsh environment Three materials available depending on the application: PVC for grinding applications (up to 176 F / 8 C) Kevlar for machine applications (up to 8 F / 25 C) Fireproof Kevlar for welding applications (up to 525 F / 275 C) provided spacer has to be added to the jaws
NGULR GRIPPER RU-82M SPRING SSISTED SERIES RU SERIES 2.8 2 Open Purge port [69.9] Ø 2.75 3 [5.3] x Ø.29 5 Close Manifold air port Supplied plugged [ 5 H9 x 13 DP ] Ø.1969 SF x.512 15..591 31. 1.22 7..276 57. 2.2 21..827 16..63 8. 3.15 Purge / Scavenge port [ M5 x 6 ] [ 5.8 h7 ] 33. 2. SF 1.299 3.1 3..122.118 37. 1.57 2 [G1/8 x 5 DP] 15..591 [ h7] Ø.1575 SF [ M6 x 12 DP] 2..787 29. 1.12 [13 f8].5118 Close 15 15 Open 5. 1.969 Opened: 13 85. 3.36 -KT: Inductive sensor Sensing range (From close position) Yellow LED Green LED KT1 to 2. 13.5 to 15.9 KT2 to.8 11.1 to 19.9 Closed: 2.9 78. 3.71 Inductive sensor Same attachment as gripper UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] How to Order: (Order Separately) BSIC MODEL RU-82M - - - SPRING SSIST ( Below) POWER INTEGRTED SENSOR P-Pneumatic H-Hydraulic POWER P Pneumatic H Hydraulic (2 bar max.) SPRING RE Closed RI Open Leave Blank. No Spring Option (standard) INDUCTIVE CSE* KT1 Sensing Range KT1 KT2 Sensing Range KT2 Leave Blank. No Inductive Option * Inductive Case not available with DU model SMPLE ORDER: RU-82M-H-RE-KT2 Ex: RU-82M Gripper, Hydraulic, Spring Closed, Sensing Range KT2 SENSOR CCESSORIES ORDER # QTY/UNIT PNP Magneto Resistive Sensor w/qk Disconnect* ** OHSP-17 1 or 2 NPN Magneto Resistive Sensor w/qk Disconnect* ** OHSN-17 1 or 2 PNP Magneto Resistive Sensor (9 Barrel) w/qk Disc* ** OHSP-11 1 or 2 NPN Magneto Resistive Sensor (9 Barrel) w/qk Disc* ** OHSN-11 1 or 2 Replacement PNP Double Inductive Sensor* *** KT15 1 Quick Disconnect 2 Meter Cable* CBL-1 1 or 2 Quick Disconnect 5 Meter Cable* CBL-13 1 or 2 Quick Disconnect 2 Meter Cable (for KT15 Inductive Sensor)* CBL-1 1 or 2 SELED BOOT KITS PVC Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-37 1 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-371 1 FireProof Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-372 1 SEL REPIR KIT PNEUMTIC HYDRULIC Viton Seal Repair Kit SLKT-157V SLKT-331V 1 *Sensor and cable sold separately Requires Mounting Kit **Piston magnet standard Not compatible with Hydraulic (-H) option and requires -RE or -RI option ***Requires KT1 or KT2 Inductive Case Option
NGULR GRIPPER RU-82M SPRING SSISTED SERIES Specifications RU-82M Total Rated Grip Force L=1 in [25.mm] @ 1 psi, 7 bar, w/spring... 276 lbs 1228 N 1 psi, 7 bar, w/o spring... 27 lbs. 922 N Stroke... 15.9 of stroke for each finger Weight... 1.55 lbs..7 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 5-1 psi 3-7 bar Cylinder Bore Ø... 2.36 in. 6 mm Displacement... 2.1 in 3. 35 cm 3 Temperature Range Viton Seals Standard... -2 ~3 F -3~15 C ctuation (open/close)....1 sec./.1 sec. ccuracy... ±.2 in. ±.5 mm Repeatability... ±.8 mm. ±.2 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position FINGER FORCE - F/2 N lbs. 25 562 2 9 15 337 1 225 5 112 1 PSI [7 bar] PSI [ bar] 1. 1.5 2. 2.5 3. 3.5..5 5. in. 25. 38.1 5.8 63.5 76.2 88.9 11.6 11.3 127 mm L GRIP FORCE PER FINGER (at with Spring ssist) 29 PSI [ 2 bar] 8 PSI [5.5 bar] Y 6 PSI [.1 bar] EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L C T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS X F/2 F/2 Loading Capacity Static Dynamic Maximum Tensile T 65 lbs. [29 N] 13 lbs. [58 N] Maximum Compressive C 65 lbs. [29 N] 13 lbs. [58 N] Maximum Moment Mx 168 in.-lbs. [19 Nm] 2 in.-lbs. [.8 Nm] Maximum Moment My 171 in.-lbs. [121 Nm] 16 in.-lbs. [12 Nm] Maximum Moment Mz 168 in.-lbs. [19 Nm] 2 in.-lbs. [.8 Nm] Capacities are per set of jaws and are not simultaneous My RU SERIES 2.9 ccessory Mounting Technical Data.715 18.2.73 19 1.212 3.8.185.7.115 2.9 OHSP/N 17 OHSP/N 11 MR Sensors PNP and NPN Magneto Resistive available Sensors are slot mounted, no mounting kits required Simple adjustment with slotted screw driver Built in LED for ease of positioning and troubleshooting vailable with 2M or 5M Quick Disconnect mating cable (order separately).51 13 PLUMBING FITTING PLFT-38 Plumbing Fittings djustable flow controls: Have thumb screw adjust with locking nut for adjusting actuation time vailable for 6mm OD tubing Plumbing fittings: For side air port location Top airport are plugged as standard.728 18.5 DJUSTBLE FLOW CONTROL G1/8 VLVF-5 dapter plate for cover set up Clamping Crown.55 13.62 16.3 2.295 58.3 Boot Protects the gripper mechanism Provides better performance and longer life time in harsh environment Three materials available depending on the application: PVC for grinding applications (up to 176 F / 8 C) Kevlar for machine applications (up to 8 F / 25 C) Fireproof Kevlar for welding applications (up to 525 F / 275 C) provided spacer has to be added to the jaws
NGULR GRIPPER RU-112M SPRING SSISTED SERIES RU SERIES 2.1 2 Open Purge port [95.3] Ø 3.75 3 [8.5] x Ø.335 5 Close Manifold air port Supplied plugged [ 8 H9 x 13 DP] Ø.315 SF x.512 Purge / Scavenge port [ M5 x 6 ] 21.5.86. 1.575 9..35 3.1.122 75. 2.953 5. 1.772 8. 1.89 32. 1.26 16..63 11. Ø.331 [ 76.2 h7 ] 3. SF 3..118 2 [G1/8 x 8 DP] [5 h7] Ø.1969 SF [ M8 x 13 DP] 22.1.87 25. 1. 38. 1.512 [19 f8].78 Close 15 15 Open 66. 2.598 -KT: Inductive sensor Opened: 13 111..37 Sensing range (F rom close position) Yellow LE D Green LE D KT1 to 1.9 17.2 to 19.1 KT2 to 5.7 13. to 19.1 Closed: 6.2 12..16 Inductive sensor Same attachment as gripper UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] How to Order: (Order Separately) POWER P H BSIC MODEL RU-112M - - - POWER P-Pneumatic H-Hydraulic Pneumatic Hydraulic (2 bar max.) SPRING SSIST ( Below) SPRING RE Closed RI Open Leave Blank. No Spring Option (standard) INDUCTIVE CSE* KT1 Sensing Range KT1 KT2 Sensing Range KT2 Leave Blank. No Inductive Option * Inductive Case not available with DU model INTEGRTED SENSOR SMPLE ORDER: RU-112M-P-RI-KT2 Ex: RU-112M Gripper, Pneumatic, Spring Open, Sensing Range KT2 SENSOR CCESSORIES ORDER # QTY/UNIT PNP Magneto Resistive Sensor w/qk Disconnect* ** OHSP-17 1 or 2 NPN Magneto Resistive Sensor w/qk Disconnect* ** OHSN-17 1 or 2 PNP Magneto Resistive Sensor (9 Barrel) w/qk Disc* ** OHSP-11 1 or 2 NPN Magneto Resistive Sensor (9 Barrel) w/qk Disc* ** OHSN-11 1 or 2 Replacement PNP Double Inductive Sensor* *** KT15 1 Quick Disconnect 2 Meter Cable* CBL-1 1 or 2 Quick Disconnect 5 Meter Cable* CBL-13 1 or 2 Quick Disconnect 2 Meter Cable (for KT15 Inductive Sensor)* CBL-1 1 or 2 SELED BOOT KITS PVC Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-373 1 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-37 1 FireProof Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-375 1 SEL REPIR KIT PNEUMTIC HYDRULIC Viton Seal Repair Kit SLKT-158V SLKT-332V 1 *Sensor and cable sold separately Requires Mounting Kit **Piston magnet standard Not compatible with Hydraulic (-H) option and requires -RE or -RI option ***Requires KT1 or KT2 Inductive Case Option
NGULR GRIPPER RU-112M SPRING SSISTED SERIES Specifications RU-112M Total Rated Grip Force L=1 in [25.mm] @ 1 psi, 7 bar, w/spring... 83 lbs. 215 N 1 psi, 7 bar, w/o spring... 36 lbs. 16 N Stroke... 19.1 of stroke for each finger Weight... 3.75 lbs. 1.7 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 5-1 psi 3-7 bar Cylinder Bore Ø... 2.99 in. 76 mm Displacement... 5.19 in 3. 85 cm 3 Temperature Range Viton Seals Standard... -2 ~3 F -3~15 C ctuation (open/close)....35 sec./.35 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.8 mm. ±.3 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position FINGER FORCE - F/2 N lbs. 6 138 5 112 899 3 67 2 9 1 225 29 PSI [ 2 bar] 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [ bar] 1 2 3 5 6 7 in. 25 51 76 12 127 152 18mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER (at with Spring ssist) Y C T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS X F/2 F/2 Loading Capacity Static Dynamic Maximum Tensile T 65 lbs. [29 N] 13 lbs. [58 N] Maximum Compressive C 65 lbs. [29 N] 13 lbs. [58 N] Maximum Moment Mx 168 in.-lbs. [19 Nm] 2 in.-lbs. [.8 Nm] Maximum Moment My 171 in.-lbs. [121 Nm] 16 in.-lbs. [12 Nm] Maximum Moment Mz 168 in.-lbs. [19 Nm] 2 in.-lbs. [.8 Nm] Capacities are per set of jaws and are not simultaneous My RU SERIES 2.11 ccessory Mounting Technical Data.715 18.2.73 19 1.212 3.8.185.7.728 18.5 OHSP/N 17.51 13 OHSP/N 11 MR Sensors PNP and NPN Magneto Resistive available Sensors are slot mounted, no mounting kits required Simple adjustment with slotted screw driver Built in LED for ease of positioning and troubleshooting vailable with 2M or 5M Quick Disconnect mating cable (order separately) PLUMBING FITTING PLFT-38 Plumbing Fittings djustable flow controls: Have thumb screw adjust with locking nut for adjusting actuation time vailable for 6mm OD tubing Plumbing fittings: For side air port location Top airport are plugged as standard DJUSTBLE FLOW CONTROL G1/8 VLVF-5 dapter plate for cover set up Clamping Crown 5.827 18.898 3. 76.3 22.8 Boot Protects the gripper mechanism Provides better performance and longer life time in harsh environment Three materials available depending on the application: PVC for grinding applications (up to 176 F / 8 C) Kevlar for machine applications (up to 8 F / 25 C) Fireproof Kevlar for welding applications (up to 525 F / 275 C) provided spacer has to be added to the jaws
NGULR GRIPPER RU-12M SPRING SSISTED SERIES 17..213 RU SERIES 2.12 Purge port 6 2 [122.2] Ø.811 3 Manifold air port Supplied plugged [ 8 H9 x 2 DP] Ø.315 SF x.787 3 [8.5] 6 x Ø.335 Close 3 Open 27. 1.63 55. 2.165 9..35 Purge / Scavenge 66. port [ G1/8 x 8 ] 2.598 3.7.16 71. 2.795 3. 1.693 22..866 1. 5.512 [17.95 h7] Ø.25 2 [G1/ x 1 DP] [6 m6] 2 x Ø.236 SF [ 2 x M8 x 18 DP] 26. 1.2 2..95 2..95 [22 f8].8661 3 Close 15 Open 95. 3.7 5..197 Opened: 13 152.5 6. -KT: Inductive sensor Same attachment as gripper Sensing range (F rom close position) Yellow LED Green LED KT1 to 2.8 1.8 to 17.6 KT2 to 5. 12.2 to 17.6 Closed:.6 1.5 5.531 15 Inductive sensor Inductive sensor UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] How to Order: (Order Separately) BSIC MODEL RU-12M - - - POWER INTEGRTED SENSOR P-Pneumatic H-Hydraulic POWER P Pneumatic H Hydraulic (2 bar max.) SPRING RE Closed RI Open Leave Blank. No Spring Option (standard) INDUCTIVE CSE KT1 KT2 SPRING SSIST ( Below) Sensing Range KT1 Sensing Range KT2 Leave Blank. No Inductive Option SENSOR CCESSORIES ORDER # QTY/UNIT Replacement PNP Double Inductive Sensor* *** KT15 1 Quick Disconnect 2 Meter Cable (for KT15 Inductive Sensor)* CBL-1 1 or 2 SELED BOOT KITS PVC Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-376 1 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-377 1 FireProof Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-378 1 SEL REPIR KIT PNEUMTIC HYDRULIC Viton Seal Repair Kit SLKT-333V SLKT-33V 1 *Sensor and cable sold separately ***Requires KT1 or KT2 Inductive Case Option SMPLE ORDER: RU-12M-H-RE-KT1 Ex: RU-12M Gripper, Hydraulic, Spring Closed, Sensing Range KT1
NGULR GRIPPER RU-12M SPRING SSISTED SERIES Specifications RU-12M Total Rated Grip Force L=1 in [25.mm] @ 1 psi, 7 bar, w/spring... 1298 lbs. 5775 N 1 psi, 7 bar, w/o spring... 886 lbs. 391 N Stroke... 17.6 of stroke for each finger Weight... 9.5 lbs..1 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 6-1 psi -7 bar Cylinder Bore Ø....13 in. 15 mm Displacement... 13.2 in 3. 215 cm 3 Temperature Range Viton Seals Standard... -2 ~3 F -3~15 C ctuation (open/close)....6 sec./.6 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.8 mm. ±.3 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position FINGER FORCE - F/2 N lbs. 75 1686 625 15 5 112 375 83 25 562 125 281 29 PSI [ 2 bar] PSI [ bar] 1 2 3 5 6 7 8 9 in. 25 51 76 12 127 152 178 23 228mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER (at with Spring ssist) 1 PSI [7 bar] Y 8 PSI [5.5 bar] 6 PSI [.1 bar] C T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS X F/2 F/2 Loading Capacity Static Dynamic Maximum Tensile T 12 lbs. [63 N] 28 lbs. [126 N] Maximum Compressive C 12 lbs. [63 N] 28 lbs. [126 N] Maximum Moment Mx 6 in.-lbs. [52 Nm] 115 in.-lbs. [13 Nm] Maximum Moment My 616 in.-lbs. [696 Nm] 611 in.-lbs. [69 Nm] Maximum Moment Mz 6 in.-lbs. [52 Nm] 115 in.-lbs. [13 Nm] Capacities are per set of jaws and are not simultaneous My RU SERIES 2.13 ccessory Mounting Technical Data 1.15 29.2.9 12. PLUMBING FITTING PLFT-39 1.67 27.1 DJUSTBLE FLOW CONTROL G1/ VLVF-1 Plumbing Fittings djustable flow controls: Have thumb screw adjust with locking nut for adjusting actuation time vailable for 6mm OD tubing Plumbing fittings: For side air port location Top airport are plugged as standard dapter plate for cover set up Clamping Crown 6.96 165 1.12 29.291 19 Boot Protects the gripper mechanism Provides better performance and longer life time in harsh environment Three materials available depending on the application: PVC for grinding applications (up to 176 F / 8 C) Kevlar for machine applications (up to 8 F / 25 C) Fireproof Kevlar for welding applications (up to 525 F / 275 C) provided spacer has to be added to the jaws
NGULR GRIPPER RU-162M SPRING SSISTED SERIES 119.5.75 RU SERIES 2.1 Purge port 6 2 [12.9] Ø 5.626 3 Manifold air port Supplied plugged [ 1 H9 x 22 DP] Ø.3937 SF x.866 3 [11] 6 x Ø.33 3 Close Open 32. 1.26 65. 2.559 11..33 Purge / Scavenge port [ G1/8 x 8 ] 5. 1.969 71. 2.795 2..95 [127. h7] Ø 5. [8 m6] 2 x Ø.315 SF 2 [G1/ x 1 DP] [ 2 x M1 x 22 DP] 165. 6.96 31.5 1.2 28. 1.12 28. 1.12 3 Close Open [ 26 f8] 1.236 15 3.7.16 79. 3.11 15..13 6..236 Opened: 13 185. 7.283 -KT: Inductive sensor Same attachment as gripper Sensing range (F rom close position) Yellow LED Green LED KT1 to 2. 1.8 to 17.2 KT2 to.6 12.6 to 17.2 Closed:.3 17.5 6.713 Inductive sensor 15 Inductive sensor UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] How to Order: (Order Separately) BSIC MODEL RU-162M - - - POWER INTEGRTED SENSOR P-Pneumatic H-Hydraulic POWER P Pneumatic H Hydraulic (2 bar max.) SPRING RE Closed RI Open Leave Blank. No Spring Option (standard) INDUCTIVE CSE KT1 KT2 SPRING SSIST ( Below) Sensing Range KT1 Sensing Range KT2 Leave Blank. No Inductive Option SENSOR CCESSORIES ORDER # QTY/UNIT Replacement PNP Double Inductive Sensor* *** KT15 1 Quick Disconnect 2 Meter Cable (for KT15 Inductive Sensor)* CBL-1 1 or 2 SELED BOOT KITS PVC Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-379 1 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-38 1 FireProof Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-381 1 SEL REPIR KIT PNEUMTIC HYDRULIC Viton Seal Repair Kit SLKT-335V SLKT-336V 1 *Sensor and cable sold separately ***Requires KT1 or KT2 Inductive Case Option SMPLE ORDER: RU-162M-H-RI-KT2 Ex: RU-162M Gripper, Hydraulic, Spring Open, Sensing Range KT2
NGULR GRIPPER RU-162M SPRING SSISTED SERIES Specifications RU-162M Total Rated Grip Force L=2 in [5.8mm] @ 1 psi, 7 bar, w/spring... 123 lbs. 59 N 1 psi, 7 bar, w/o spring... 853 lbs. 379 N Stroke... 17.2 of stroke for each finger Weight... 1.8 lbs. 6.7 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 6-1 psi -7 bar Cylinder Bore Ø....72 in. 12 mm Displacement... 19.7 in 3. 322 cm 3 Temperature Range Viton Seals Standard... -2 ~3 F -3~15 C ctuation (open/close)....8 sec./.8 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.8 mm. ±.3 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position FINGER FORCE - F/2 N lbs. 75 1686 625 15 5 112 375 83 25 562 125 281 29 PSI [ 2 bar] PSI [ bar] 2 3 5 6 7 8 9 1 11 in. 51 76 12 127 152 178 23 229 25 28mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER (at with Spring ssist) 1 PSI [7 bar] Y 8 PSI [5.5 bar] 6 PSI [.1 bar] C T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS X F/2 F/2 Loading Capacity 1 Static Dynamic Maximum Tensile T 189 lbs. [8 N] 38 lbs. [168 N] Maximum Compressive C 189 lbs. [8 N] 38 lbs. [168 N] Maximum Moment Mx 66 in.-lbs. [75 Nm] 166 in.-lbs. [18.8 Nm] Maximum Moment My 9293 in.-lbs. [15 Nm] 885 in.-lbs. [1 Nm] Maximum Moment Mz 66 in.-lbs. [75 Nm] 166 in.-lbs. [18.8 Nm] Capacities are per set of jaws and are not simultaneous My RU SERIES 2.15 ccessory Mounting Technical Data 1.15 29.2 1.67 27.1.9 12. PLUMBING FITTING PLFT-39 DJUSTBLE FLOW CONTROL G1/ VLVF-1 Plumbing Fittings djustable flow controls: Have thumb screw adjust with locking nut for adjusting actuation time vailable for 6mm OD tubing Plumbing fittings: For side air port location Top airport are plugged as standard dapter plate for cover set up Clamping Crown 7.8 19 1.339 3.783 121.5 Boot Protects the gripper mechanism Provides better performance and longer life time in harsh environment Three materials available depending on the application: PVC for grinding applications (up to 176 F / 8 C) Kevlar for machine applications (up to 8 F / 25 C) Fireproof Kevlar for welding applications (up to 525 F / 275 C) provided spacer has to be added to the jaws
NGULR GRIPPER VULCN-112M HIGH TEMPERTURE SERIES VULCN SERIES 2.16 TOP BLOWING PORT [M5 x 5 DP] 3 D [95.25] Ø 3.75 [8.5] x Ø.33 3 5 TOP IR PORTS [M5 x 5 DP] [ 8 H9 x 13 DP] Ø.315 SF x.51 DP BLOWING PORT [M5 x 5 DP] (Supplied Plugged) 21.5.86 9.35 1.575 3.1.122 75 2.953 32 1.26 5 1.77 8 1.89 66 2.6 IR PORTS [G1/8 x 8 DP] (Supplied Plugged) 16.63 Ø 3.12 11.331 [76.2 h7] 3. SF 38. 1.512 15.6.61 22.1.87 [25. ±.25] 1. [ 19 f8].78 [5 h7] 2 x Ø.1969 SF [ M8 x 13 DP] D 15 BLOWING 15 2 D 6.2 T : Output Shaft for Sensing 35 D 1.38 25.98 ET : Stainless Steel Heat Shield 37.5 1.8 76 2.99 1.1 5.52 E3 or E5 : Fireproof Kevlar Boot 76.3 3. [M6] 13 15.59 13 Ø5.28 18 Ø5.83 N lbs. 5 112 [15 h8] Ø.596 SF FINGER FORCE - F/2 3 2 1 899 67 9 225 1 PSI [7 bar] PSI [ bar] 29 PSI [ 2 bar] 8 PSI [5.5 bar] GRIP FORCE PER FINGER (at with Spring ssist) WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS 6 PSI [.1 bar] UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] 1. 2. 3.. 5. 6. 7. in. 25 51 76 12 127 152 178 mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L Y C T Mx X F/2 F/2 Loading Capacity Static Dynamic Maximum Tensile T 17 lbs. [75 N] 21 lbs. [95 N] Maximum Compressive C 17 lbs. [75 N] 21 lbs. [95 N] Maximum Moment Mx 319 in.-lbs. [36 Nm] 8 in.-lbs. [9 Nm] Maximum Moment My 2159 in.-lbs. [2 Nm] 212 in.-lbs. [2 Nm] Maximum Moment Mz 319 in.-lbs. [36 Nm] 8 in.-lbs. [9 Nm] Capacities are per set of jaws and are not simultaneous My Specifications Total Rated Grip Force L=1 in [25.mm] @ VULCN-112M 1 psi, 6.9 bar, w/spring... 895 lbs. 3983 N 1 psi, 6.9 bar, w/o spring... 667 lbs. 2965 N Stroke... 19.2 of stroke for each finger Weight... 3.75 lbs. 1.7 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 5-1 psi 3-7 bar Cylinder Bore Ø... 2.99 in. 76 mm Displacement... 5.3 in 3. 87 cm 3 Temperature Range Viton Seals Standard... -2 ~32 F -3~16 C -HT Dynamic Steel Ring... Up to 8º Up to 5º ctuation (open/close)....1 sec./.1 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.8 mm. ±.2 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position How to Order: (Order ccessories separately from Basic Model) BSIC MODEL SELS SPRING SENSING VULCN-112M - HT - RI - T - E5 PROTECTION SELS HT* Dynamic Steel Ring (Up to 5ºC) Leave Blank. Viton Seals up to 16º (Standard) SPRING RE Closed RI Open Leave Blank. No Spring Option (Standard) SENSING T* Rear Output Shaft for Sensing Leave Blank. No Sensing Option (Standard) PROTECTION E3 Fire-proof Kevlar Sealed Jaw Boot (up to 275ºC) E5 Fire-proof Kevlar Sealed Jaw Boot (up to 5ºC) ET Stainless Steel Heat Shield Leave Blank. No Protection Option (Standard) SELED BOOT KITS ORDER # QTY/UNIT -E3 Fire Proof Kevlar Sealed jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-375 1 -E5 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-55 1 SEL REPIR KIT Viton Seal Repair Kit SLKT-158V 1 -HT Dynamic Steel Ring Repair Kit SLKT-58 1 SMPLE ORDER: VULCN-112M-HT-RI-E5 Ex: Vulcan-112M Gripper, Dynamic Steel Ring, Spring Open, Fire-proof Kevlar Sealed Jaw Boot up to 5º C *HT and T Options are not compatible.
NGULR GRIPPER VULCN-12M HIGH TEMPERTURE SERIES 6 TOP BLOWING PORT [G1/8 x11 DP] 15 [8.5] 6 x Ø.33 [122.2] Ø.811 TOP IR PORTS [M6 x 7 DP] [8 H9 x 2 DP] Ø.315 SF x.79 DP D 55 D 2.17 2 1.65 3 T : Output Shaft for Sensing 3 55 2.165 BLOWING PORT [G1/8 x 8 DP] (Supplied Plugged) 27 1.63 9.35 3.7.15 11.33 5 2.13 17.213 3 1.69 66 2.6 71 2.8 95 3.7 IR PORTS [G1/ x 1 DP] (Supplied Plugged) 22.87 ET : Stainless Steel Heat Shield 177 Ø6.97 16.63 5 2.126 1 5.512 26 1.2 [2 ±.25].99 [ 17.95 h 7] Ø.25 SF 2.9 5.2 19.29 [6 m6] 2 x Ø.236 SF [22 f8].8661 E3 or E5 : Fireproof Kevlar Boot [ 2 x M8 x 18 DP] D BLOWING 2 3 15 VULCN SERIES 2.17 N lbs. 7 1573 13 D.6 2.79 [M8] [ Ø15 h8 h8] Ø.596SF 168 Ø6.61 165 Ø6.5 FINGER FORCE - F/2 6 138 5 112 899 3 67 2 9 1 225 1 PSI [7 bar] PSI [ bar] 29 PSI [ 2 bar] GRIP FORCE PER FINGER (at with Spring ssist) 8 PSI [5.5 bar] 6 PSI [.1 bar] WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] 2. 3.. 5. 6. 7. 8. 9. in. 5.8 76.2 11.6 127 152. 177.8 23.2 228.6 mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L Y C T Mx X F/2 F/2 Loading Capacity Static Dynamic Maximum Tensile T 12 lbs. [63 N] 28 lbs. [126 N] Maximum Compressive C 12 lbs. [63 N] 28 lbs. [126 N] Maximum Moment Mx 6 in.-lbs. [52 Nm] 115 in.-lbs. [13 Nm] Maximum Moment My 616 in.-lbs. [696 Nm] 611 in.-lbs. [69 Nm] Maximum Moment Mz 6 in.-lbs. [52 Nm] 115 in.-lbs. [13 Nm] Capacities are per set of jaws and are not simultaneous My Specifications Total Rated Grip Force L=2 in [5.8mm] @ VULCN-12M 1 psi, 6.9 bar, w/spring... 133 lbs. 5975 N 1 psi, 6.9 bar, w/o spring... 917 lbs. 79 N Stroke... 17.6 of stroke for each finger Weight... 9. lbs..1 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 6-1 psi -7 bar Cylinder Bore Ø....13 in. 15 mm Displacement... 13.1 in 3. 215 cm 3 Temperature Range Viton Seals Standard... -2 ~32 F -3~16 C -HT Dynamic Steel Ring... Up to 8º Up to 5º ctuation (open/close)....16 sec./.16 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.8 mm. ±.2 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position How to Order: (Order ccessories separately from Basic Model) BSIC MODEL SELS SPRING SENSING VULCN-12M - HT - RI - T - ET PROTECTION SELS HT* Dynamic Steel Ring (Up to 5ºC) Leave Blank. Viton Seals up to 16º (Standard) SPRING RE Closed RI Open Leave Blank. No Spring Option (Standard) SENSING T* Rear Output Shaft for Sensing Leave Blank. No Sensing Option (Standard) PROTECTION E3 Fire-proof Kevlar Sealed Jaw Boot (up to 275ºC) E5 Fire-proof Kevlar Sealed Jaw Boot (up to 5ºC) ET Stainless Steel Heat Shield Leave Blank. No Protection Option (Standard) SELED BOOT KITS ORDER # QTY/UNIT -E3 Fire Proof Kevlar Sealed jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-378 1 -E5 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-56 1 SEL REPIR KIT Viton Seal Repair Kit SLKT-333V 1 -HT Dynamic Steel Ring Repair Kit SLKT-59 1 SMPLE ORDER: VULCN-12M-T-ET Ex: Vulcan-12M Gripper, Rear Output Shaft for Sensing, Stainless Steel Heat Shield *HT and T Options are not compatible.
NGULR GRIPPER VULCN-162M HIGH TEMPERTURE SERIES VULCN SERIES 2.18 6 TOP BLOWING PORT [G1/8 x 11 DP] 15 [11] 6 x.3 [12.9] Ø 5.626 TOP IR PORTS [M6 x 7 DP] [1 H9 x 22 DP] Ø.3937 SF x.87 DP D 3 3 BLOWING PORT [G1/8 x 8 DP] (Supplied Plugged) T : Output Shaft for Sensing 32 1.26 11.3 65 2.559 3.7.15 119.5.75 5 1.97 71 2.8 79 3.11 15.13 IR PORTS [G1/ x 12 DP] (Supplied Plugged) 2.9 6.2 165 6.96 [127 h7] Ø5. SF ET : Stainless Steel Heat Shield 31.5 1.2 D 2.9 53. 12 26.72 6 Ø8.11 38 2.36 1.5 23.5.93 58 2.283 [28 ±.25] 1.12 28 1.1 E3 or E5 : Fireproof Kevlar Boot 121.5.78 [8 m6] 2 x Ø.315 SF [26 f8] 1.236 [ 2 x M1 x 22 DP] D BLOWING 2 3 15 13 2.79 [M8] 19 Ø7.8 19 Ø7.8 N lbs. 12 2697 D [15 h8].3 Ø.596 SF 1 227 FINGER FORCE - F/2 8 1798 6 138 899 2 9 1 PSI [7 bar] PSI [ bar] 29 PSI [ 2 bar] 8 PSI [5.5 bar] GRIP FORCE PER FINGER (at with Spring ssist) 6 PSI [.1 bar] WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] 2. 3.. 5. 6. 7. 8. 9. 1. in. 51 76 12 127 152 178 23 229 25 mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L Y C T Mx X F/2 F/2 Loading Capacity 1 Static Dynamic Maximum Tensile T 189 lbs. [8 N] 38 lbs. [168 N] Maximum Compressive C 189 lbs. [8 N] 38 lbs. [168 N] Maximum Moment Mx 66 in.-lbs. [75 Nm] 166 in.-lbs. [18.8 Nm] Maximum Moment My 9293 in.-lbs. [15 Nm] 885 in.-lbs. [1 Nm] Maximum Moment Mz 66 in.-lbs. [75 Nm] 166 in.-lbs. [18.8 Nm] Capacities are per set of jaws and are not simultaneous My Specifications Total Rated Grip Force L=2 in [5.8mm] @ VULCN-162M 1 psi, 6.9 bar, w/spring... 215 lbs. 896 N 1 psi, 6.9 bar, w/o spring... 1393 lbs. 6198 N Stroke... 17.3 of stroke for each finger Weight... 1.77 lbs. 6.7 kg Pressure Range (without springs)... 3-1 psi 2-7 bar Pressure Range (with springs)... 6-1 psi -7 bar Cylinder Bore Ø....72 in. 12 mm Displacement... 19.7 in 3. 322 cm 3 Temperature Range Viton Seals Standard... -2 ~32 F -3~16 C -HT Dynamic Steel Ring... Up to 8º Up to 5º ctuation (open/close)....21 sec./.21 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.8 mm. ±.2 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position How to Order: (Order ccessories separately from Basic Model) BSIC MODEL SELS SPRING SENSING VULCN-162M - HT - RI - T - E3 PROTECTION SELS HT* Dynamic Steel Ring (Up to 5ºC) Leave Blank. Viton Seals up to 16º (Standard) SPRING RE Closed RI Open Leave Blank. No Spring Option (Standard) SENSING T* Rear Output Shaft for Sensing Leave Blank. No Sensing Option (Standard) PROTECTION E3 Fire-proof Kevlar Sealed Jaw Boot (up to 275ºC) E5 Fire-proof Kevlar Sealed Jaw Boot (up to 5ºC) ET Stainless Steel Heat Shield Leave Blank. No Protection Option (Standard) SELED BOOT KITS ORDER # QTY/UNIT -E3 Fire Proof Kevlar Sealed jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-381 1 -E5 Kevlar Sealed Jaw Boot Kit (includes 2 interfaces, 1 collar, 1 boot) SLKT-57 1 SEL REPIR KIT Viton Seal Repair Kit SLKT-335V 1 -HT Dynamic Steel Ring Repair Kit SLKT-6 1 SMPLE ORDER: VULCN-162M-RE-T-E3 Ex: Vulcan-162M Gripper, Spring Closed, Rear Output Shaft for Sensing, Fireproof Kevlar Sealed Jaw Boot up to 275º *HT and T Options are not compatible.
RU/VULCN SERIES EXPLODED VIEW 56 6 8 57 3 1 65 2 62 61 9 63 6 Item Qty Name 1 1 Body 2 1 Piston 3 1 Cam Driver 1 Cap 6 2 Jaw 8 1 Shielded case 9 2 Pivot Pin 52 2 SS Screw, Cap 53 SHC Screw, Cap 56 1 Magnet 57 2 SS Screw, Body 61 1 SHC Screw, Piston 62 1 Nut, Piston 63 Pin, Jaw 6 2 Screw, Shielded case 65 1 Springs 9 1 KT Body 91 1 KT Body, O-Ring 92 1 KT Sensor 93 1 KT Body, Screw 9 1 Target 95 1 Target, Screw 96 2 KT Body, O-Ring 97 1 KT Body, Screw 98 1 Wire Holder 99 3 KT Body, Screw 1 1 Cap for KT Shaft 11 1 Shaft 12 1 KT Body, Pin RU/VULCN SERIES MINTENNCE 2.19 NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. 99 9 52 53 92 93 91 96 98 97 -KT Option 9 95 1 11 1 12 ssembly Procedure 1) Lubricate and install the seals onto the cap (x3), the piston (x2) and the body (x1). 2) If top airports are used, remove the plug screws from the cap (#) and insert into side airports of the body (#1). 3) ssemble the piston (#2) and the cam driver (#3) with the washer and the screw. - RE option : Place the counterbore holes of the piston on the cam driver side. - RI option : Place the counterbore holes of the piston on the screw side. ) Insert the piston into the body. Orientate the piston so that the magnets are placed in front of the body slots. - RE option : insert the springs (#65) between the body and the piston in the counterbore holes. 5) Place and screw the cap onto the body. The dowel holes of the cap and of the body have to be aligned. - RI option : insert the springs (#65) between the cap and the piston in the counterbore holes. 6) Lubricate the slots and the jaws (#6) and the groove of the cam driver. 7) Place the jaws into the body slot and insert the pivot pin aligning with the jaw hole. The flat of the pivot pin has put in front of the rear side of the body. Screw SS screw into the body to prevent the pivot pin from moving. 8) ttach the shielded case. SK Seal Repair Kit Order # s Product Data Sheets SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
RU/VULCN SERIES EXPLODED VIEW Item Qty Name RU/VULCN SERIES MINTENNCE 2.2 9 6 8 65 1 1 1 Body 2 1 Piston 3 1 Cam Driver 1 Cap 6 2 Jaw 8 1 Shielded case 9 2 Pivot Pin 52 2 SS Screw, Cap 53 SHC Screw, Cap 56 1 Magnet 57 2 SS Screw, Body 61 1 SHC Screw, Piston 62 1 Nut, Piston 63 Pin, Jaw 6 2 Screw, Shielded case 65 1 Springs 3 2 NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. CCESSORY INSTLLTION & DJUSTMENT INSTRUCTIONS Installation - MR Sensors 1) Insert sensors (#9) for either end of the profile slots 2) Set the sensors with the integrated screw 81 9 8 86 Installation - Boot 1) Mount the gripper onto the customer mounting plate 2) Insert the spacer (#81) into the pins of the jaws 3) Insert sensor slot plugs (#82) into sensor mounting groove. Install the boot (#8) on the gripper. The jaw opening of the boot has to fit with the spacer. Insert lip of boot seal into the groove of the gripper ) Use the clamping ring (#83) to fasten the boot on the gripper 5) ttach fingers to the jaws (ensure that boot is sealed between the jaws and the finger) 82 8 87 88 85 Installation - Stainless Steel Shield 1) Mount the gripper onto the customer mounting plate 2) Insert the spacer plate (#88) using (2) fasteners (#87) to the center of the gripper 3) Install the stainless steel shield (#8) using the (2) fasteners (#86) on top of the stainless steel shield and the () fasteners (#85) on the side of the stainless steel shield ) Install fingers to gripper as required 83 SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
QULITY PRECISION DESIGNDURBILITY NOTES PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY 2.21 PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY RU/VULCN SERIES
ngular Grippers- Cam Driven Series R SERIES 2.22 General Purpose: This style gripper is widely used in the industry and is a rugged design that supplies very high grip force for its size. Cost Effective: The simplified drive mechanism makes these grippers an excellent value. Mounting Information: Gripper can be mounted and operated in any orientation Technical Specifications: Pneumatic Specifications Imperial Metric Pressure Operating Range -1 psi 3-7 bar Cylinder Type Double cting Dynamic Seals Internally Lubricated Buna-N Valve Required to Operate -way, 2-position ir Quality Requirements ir Filtration ir Lubrication ir Humidity Micron or Better Not Necessary* Low Moisture Content (dry) Body mounts with screws and locates with slip fit dowel pins for accuracy G Warning! Protect jaw mechanism from falling debris when mounted upside down Temperature Operating Range Buna-N Seals (standard) -3 ~18 F -35 ~8 C Viton Seals (optional) -2 ~3 F -3 ~15 C Maintenance Specifications Expected Life Normal pplication 5 million cycles w/ Preventative Maintenance 1+ million cycles* Field Repairable Yes Seal Repair Kits vailable Yes *ddition of lubrication will greatly increase service life Maintenance Section Fingers attach to jaws with screws and locate by keying
Product Features Hard Coat nodize The body has hard-coat anodize 6 RC with Teflon impregnation Quality Components Dynamic components are hardened for wear resistance and long life Style -R ngular Gripper Size -5M Style: R-5 R-5M Stroke: 15 each finger Grip Force: 2 lbs. 89 N Weight:.25 lbs..11 Kg One Piece Body One piece 775-T6 aircraft quality aluminum body Quality Manufacturing Components are precision ground for minimal jaw play Sensor Magnets Standard Style -R ngular Gripper Page 2.2 Size -6M Style: R-6 R-6M Stroke: 15 each finger Grip Force: lbs. 196 N Weight:.68 lbs..31 Kg R SERIES 2.23 Page 2.25 Stop Screw Limits open position of jaws Self-Lubricating Seals Self lubricating dynamic seals (Buna-N only) Style -R ngular Gripper Size -1M Style: R-1 R-1M Stroke: 15 each finger Grip Force: 16 lbs. 71 N Weight:.6 lbs..3 Kg Operating Principle Cap Page 2.28 Piston Body Cam Shaft djustment Plate Jaw Pressure Exhaust Exhaust Pressure Open Position Closed Position double acting piston is connected by a shaft to a cam. The cam rolls in a slot located in each of the jaws converting vertical motion of the wedge into angular synchronous motion of the jaws. This gripper is suitable for internal or external gripping. Designed and manufactured in the US
NGULR GRIPPER R-5M CM DRIVEN SERIES R SERIES 2.2 1.187 [3.1] 1.1 [25.7].75 [19.1] LC.375 [9.5] 1.75 [.5].88 [22] LC STROKE DJUSTMENT 8X #- X.18 DP [M3 X DP] LC.25 [6.].125 [3.2] 2X #1-32 [M5] IR PORTS ().19 [5].51 [13] Specifications R-5 R-5M Total Rated Grip Force F @ 1 psi, 7 bar. 2 lbs. 89 N Stroke... 15 of stroke for each finger Open Stroke djustment... 15 of stroke for each finger Weight....25 lbs..11 Kg Pressure Range... -1 psi 3-7 bar Cylinder Bore Ø....813 in. 2.6 mm Displacement....13 in 3. 2.1 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....1 sec..1 sec. ccuracy... ±.5 in. ±.13 mm Repeatability... ±.3 in. ±.8 mm Valve required to actuate... -way, 2-position 1.377 [35.] 1.313 [33.] L C 2X #- X.12 DP [M3 X 3 DP] 2X #- X.18 DP [M3 X DP] 15 STROKE.25 [6.] 1.25 [31.8] NOTE: JWS 1 PST PRLLEL.99.1 [12.7.3].125 [3.2] 1.5 [38.1] 1.1875 [3.16].75 [19.1].375 [9.5] LC.25 [6.] UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW.75 [1.9] LC.5 [12.7] 1. [25.] 2X #8-32 X.38 DP [M X 9 DP] 3X Ø.125 SF X.18DP [Ø 3 H7 X DP] Dimensions are symmetrical about centerline Metric Threads Course Pitch Third ngle Projection ll Dowel Holes are SF (Slip Fit). Locational Tolerance ±.5" or [±.13mm] Imperial in. Metric [mm]. = ±.1 [.] = [±.25]. = ±.5 [.] = [±.13]. = ±.5 [.] = [±.13] Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N lbs. 5 1 36 27 18 9 8 6 2 L GRIP FORCE PER FINGER C 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar].5 1 1.5 13 25 38 EFFECTIVE FINGER LENGTH - L T M X Y F/2 WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS M 2 in. 5mm M Y F/2 X BSIC MODEL R-5 M- METRIC V VITON SELS SENSOR CCESSORIES ORDER # QTY/UNIT mm NPN Magneto Resistive Sensor* OHSN-17 1 or 2 mm PNP Magneto Resistive Sensor* OHSP-17 1 or 2 mm NPN 9 Magneto Resistive Sensor* OHSN-11 1 or 2 mm PNP 9 Magneto Resistive Sensor* OHSP-11 1 or 2 Quick Disconnect 2 Meter Cable Length* CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length* CBL-13 1 or 2 PNEUMTIC CCESSORIES Fail Safe Valve (Imperial) OFSV-1 1 Fail Safe Valve (Metric) OFSV- 1 Standard Seal Repair Kit SLKT-22 1 Viton Seal Repair Kit SLKT-22V 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 1 lbs. N 1 lbs. N Maximum Compressive C 1 lbs. N 1 lbs. N Maximum Moment Mx 1 in.-lbs. 1.1 Nm 1 in.-lbs. 1.1 Nm Maximum Moment My 1 in.-lbs. 1.1 Nm 1 in.-lbs. 1.1 Nm Maximum Moment Mz 1 in.-lbs. 1.1 Nm 1 in.-lbs. 1.1 Nm Capacities are per set of jaws and are not simultaneous.7 [18] HLL EFFECT SENSOR FILSFE VLVE.63 [16] 2.2 [61] MIN.
NGULR GRIPPER R-6M CM DRIVEN SERIES 1. [25.] LC.5 [12.7] 2.18 [61.] STROKE DJUSTMENT 8X #8-32 X.38DP [M X 9DP] LC.375 [9.5].187 [.7] 2X #1-32 [M5] IR PORTS() Specifications R-6 R-6M Total Rated Grip Force F @ 1 psi, 7 bar lbs. 196 N Stroke... 15 of stroke for each finger Open Stroke djustment... 15 of stroke for each finger Weight....69 lbs..31 Kg Pressure Range... -1 psi 3-7 bar Cylinder Bore Ø... 1.25 in. 31.8 mm Displacement....3 in 3..9 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....11 sec..11 sec. ccuracy... ±.5 in. ±.13 mm Repeatability... ±.3 in. ±.8 mm Valve required to actuate... -way, 2-position R SERIES 2.25 1.19 [3] LC LC 2X #8-32 X.19DP [M X DP].2 [6].6 [15] 2X #8-32 X.38DP [M X 9DP] 1.82 [37.6] 1.25 [31.8] 1.95 [9.6] 1.792 1.75 [5.5] [.5] 15 STROKE.375 [9.5] 1.626 [1.3] NOTE: JWS 1 PST PRLLEL.785.1 [19.1.3].187 [.7].82 [21.].21 [1.7] 2X.75 [1.9] 2. [5.8] 1.6875 [2.86] LC LC 3X Ø.125SF X.18DP [ØH7 X DP] 2X #1-32 X.5DP [M5 X 12DP].312 [7.9].62 [15.8] 1.5 [38.1] UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Dimensions are symmetrical about centerline Metric Threads Course Pitch Third ngle Projection ll Dowel Holes are SF (Slip Fit). Locational Tolerance ±.5" or [±.13mm] Imperial in. Metric [mm]. = ±.1 [.] = [±.25]. = ±.5 [.] = [±.13]. = ±.5 [.] = [±.13] Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N lbs. 111 25 89 2 67 15 5 1 22 5 L GRIP FORCE PER FINGER.5 1 1.5 2 13 25 38 5 EFFECTIVE FINGER LENGTH - L C 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] T M X Y F/2 WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS M 2.5 in. 6mm M Y F/2 X BSIC MODEL R-6 M- METRIC V VITON SELS SENSOR CCESSORIES ORDER # QTY/UNIT mm NPN Magneto Resistive Sensor* OHSN-17 1 or 2 mm PNP Magneto Resistive Sensor* OHSP-17 1 or 2 mm NPN 9 Magneto Resistive Sensor* OHSN-11 1 or 2 mm PNP 9 Magneto Resistive Sensor* OHSP-11 1 or 2 Quick Disconnect 2 Meter Cable Length* CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length* CBL-13 1 or 2 PNEUMTIC CCESSORIES Fail Safe Valve (Imperial) OFSV-1 1 Fail Safe Valve (Metric) OFSV- 1 Standard Seal Repair Kit SLKT-23 1 Viton Seal Repair Kit SLKT-23V 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 2 lbs. 89 N 2 lbs. 89 N Maximum Compressive C 2 lbs. 89 N 2 lbs. 89 N Maximum Moment Mx 2 in.-lbs. 2.3 Nm 2 in.-lbs. 2.3 Nm Maximum Moment My 2 in.-lbs. 2.3 Nm 2 in.-lbs. 2.3 Nm Maximum Moment Mz 2 in.-lbs. 2.3 Nm 2 in.-lbs. 2.3 Nm Capacities are per set of jaws and are not simultaneous 1.1 [26] HLL EFFECT SENSOR FILSFE VLVE 2.67 [68] MIN..63 [16]
R-5 & 6 SERIES EXPLODED VIEW R 5 & 6 SERIES MINTENNCE 2.26 SK 5 Item Qty Name 1 1 Body 2 2 Jaw 3 1 Wedge 1 Piston 5 1 Cap 6 1 Plate, djustment 3 1 SSS, Nylon Patch, Cup Point 31 2 Dowel Pin 2 Magnet NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. ssembly Procedure 1) Lubricate and install seals. 2) Glue magnet into piston. 3) Install piston and wedge. ) Install jaws (press dowel pins through fingers from air port side). 5) Install cap and retaining ring. 6) Install adjustment plate. 7) Set adjustment screw for desired stroke. 7 SK SK Seal Repair Kit Order # s Product Data Sheets 1 2 31 3 6 3 SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
R-5 & 6 SERIES SSEMBLED VIEW 1 5 7 Item Qty Name 1 1 Body 2 2 Jaw 3 1 Wedge 1 Piston 5 1 Cap 6 1 Plate, djustment 3 1 SSS, Nylon Patch, Cup Point 31 2 Dowel Pin 2 Magnet NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. R 5 & 6 SERIES MINTENNCE 2.27 3 2 3 31 6 CCESSORY INSTLLTION & DJUSTMENT INSTRUCTIONS 2 Installation 1) Install sensors in profile slots as shown. 2) Set with integrated set screw. 1 SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
NGULR GRIPPER R-1M CM DRIVEN SERIES R SERIES 2.28 Ø.938 SF X.8 DP [Ø 2 H7 X 2 DP].75 [19.1] VIEW - 1. [25.].75 [19.1] LC LC 1. [25.] 2X #6-32 X.25 DP [M X 6 DP] Specifications R-1 R-1M Total Rated Grip Force F @ 1 psi, 7 bar. 16 lbs. 71 N Stroke... 15 of stroke for each finger Weight....63 lbs..3 Kg Pressure Range... -1 psi 3-7 bar Cylinder Bore Ø....813 in. 2.6 mm Displacement....26 in 3.. cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation Time....8 sec..8 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.1 in. ±.3 mm Valve required to actuate... -way, 2-position 2X #6-32 X.25 DP [M X 6DP].75 [19.1] STROKE NOTE: JWS 1 PST PRLLEL LC 3.5 [12.7].813 [2.7] 2X #3-56 [M3] IR PORTS () (FITTINGS SUPPLIED FOR.6 [2.] TUBING ID.37 [9].16 [].25 [6.] L C.3 [9] 1.62 [27.] X #6-32 [M3] THRU.31.1 [7.87.3].126 [3.2].13 [3].562 [1.3] LC 1.37 [36.5].187 [.7] UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N lbs. 36 8 31 7 27 6 22 5 18 13 3 9 2 5 1 GRIP FORCE PER FINGER 5 1 13 25 EFFECTIVE FINGER LENGTH - L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS M 1.5 38 mm BSIC MODEL R-1 M- METRIC PNEUMTIC CCESSORIES ORDER # QTY/UNIT Standard Seal Repair Kit SLKT-18 1 Viton Seal Repair Kit SLKT-18V 1 V VITON SELS L C T Y F/2 F/2 X M X M Y Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 5 lbs. 22 N 5 lbs. 22 N Maximum Compressive C 5 lbs. 22 N 5 lbs. 22 N Maximum Moment Mx 5 in.-lbs..6 Nm 5 in.-lbs..6 Nm Maximum Moment My 5 in.-lbs..6 Nm 5 in.-lbs..6 Nm Maximum Moment Mz 5 in.-lbs..6 Nm 5 in.-lbs..6 Nm Capacities are per set of jaws and are not simultaneous
R-1 SERIES EXPLODED VIEW 2 Item Qty Name 1 1 Body 2 1 Cap 3 2 Jaw 1 Piston 5 1 Shaft 6 1 Pin 31 2 Dowel Pin NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. R-1 SERIES MINTENNCE 2.29 SK Seal Repair Kit Order # s Product Data Sheets 5 6 3 1 31 SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
R-1 SERIES SSEMBLED VIEW R-1 SERIES MINTENNCE 2.3 1 2 5 Item Qty Name 1 1 Body 2 1 Cap 3 2 Jaw 1 Piston 5 1 Shaft 6 1 Pin 31 2 Dowel Pin NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. 6 31 3 SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
QULITY PRECISION DESIGNDURBILITY NOTES PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY 2.31 PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY R SERIES
ngular Grippers- 18 Series DCT/CT SERIES 2.32 18 angular gripper: The full jaw opening (18 ) means that the part can be direct fed, avoiding any release movement by the robot or by the actuator. Multiple mounting locations: DIRECTCONNECT mounting on back of body (sizes 12-25). Standard mounting on top. Compact gripper: This gripper is designed for use in confined spaces. Multipurpose gripper: Several accessories (adjustable stop, magneto resistive or inductive sensors*) allow this gripper to be used in a number of applications. Harsh environments: Shielded design repels chips and other particulate from internal drive mechanism. * Inductive sensors not available on CT-12 TM Mounting Information: Gripper can be mounted and operated in any orientation Gripper is located from the top with 2 dowel pins and assembled with 2 screws. DIRECTCONNECT mounting pattern: Gripper is located with 2 dowel pins and assembled with screws. lternative pattern: Gripper is located with 2 dowel pins and assembled with 2 screws. Technical Specifications: Pneumatic Specifications Imperial Metric Pressure Operating Range -1 psi 3-7 bar Cylinder Type Double cting Dynamic Seals Internally Lubricated Buna-N Valve Required to Operate -way, 2-position ir Quality Requirements ir Filtration ir Lubrication ir Humidity Micron or Better Not Necessary* Low Moisture Content (dry) Temperature Operating Range Buna-N Seals (Standard) -3 ~18 F -35 ~8 C Viton Seals (Optional) -2 ~3 F -3 ~15 C Fingers are centered over the jaws, located with 1 dowel pin and assembled with 2 screws. G Gripper can be operated utilizing top manifold air ports. The gripper is protected from falling debris when it is mounted and operated upside down. Maintenance Specifications Expected Life Normal pplication 5 million cycles w/ Preventative Maintenance 1+ million cycles* Field Repairable Yes Seal Repair Kits vailable Yes *ddition of lubrication will greatly increase service life Maintenance Section
Inductive Sensor Mounting Kit ccessory (SD) in order to sense jaw position. Comes with 2 holders for tubular sensors and 2 adjustable flags (except size -12). Jaw Drive Pin Driver Gripper ttachment Gripper mounting from side or bottom Viton Seals Viton seals for high temperatures (-2 F to +3 F / -3 ~15 C) are optional Quality Components Made from aluminum alloy anodized with Teflon impregnation. The gripper's main components are made of heat treated steel. Product Features Magneto Resistive Sensor Mounting Kit Standard mounting slots for magneto resistive sensors. (sensors sold separately) Operating Principle djustable Stop ccessory (BR) in order to adjust the opening of jaws, between to 18 Shielded Plate and Wiper Covers Gripper body is shielded to repel chips and other particulate from internal drive mechanism Mounting Patterns DIRECTCONNECT mounting surface on back of body (sizes 12-25) Shielded Plate Multiple ir Ports Side or top air ports (top ports require O-ring) Drive Pin Slot Pivot Pin Wiper Cover Style-DCT ngular Gripper Style: DCT-12M Size -12M Stroke: 9 each finger Grip Force: 7.2 lbs 32 N Weight:.2 lbs.9 Kg Page 2.3 Style-DCT ngular Gripper Style: DCT-16M Size -16M Stroke: 9 each finger Grip Force: 16 lbs 7 N Weight:.35 lbs.16 Kg Page 2.35 Style-DCT ngular Gripper Style: DCT-2M Size -2M Stroke: 9 each finger Grip Force: 25 lbs 112 N Weight:.62 lbs.28 Kg Page 2.36 Style-DCT ngular Gripper Style: DCT-25M Size -25M Stroke: 9 each finger Grip Force: 35 lbs 157 N Weight: 1.8 lbs.9 Kg Page 2.37 Style-CT ngular Gripper Style: CT-32M Size -32M Stroke: 9 each finger Grip Force: 61 lbs 272 N Weight: 1.59 lbs.72 Kg Page 2.38 DCT/CT SERIES 2.33 Body Cap Piston Magnet Style-CT ngular Gripper Style: CT-M Size -M Stroke: 9 each finger Grip Force: 1 lbs 6 N Weight: 2.6 lbs 1.18 Kg TM Page 2.39 Exhaust Pressure Pressure Exhaust double acting piston, with a ring magnet for magneto resistive sensing, is connected to a fork driver on which 2 drive pins are fixed. Jaw rotation is synchronized with the drive pin-jaw assembly. Sliding in these slots, drive pins convert vertical motion of the piston into rotating opposite synchronous motion of both jaws. Each jaw has a useful rotation stroke of 9, between the 9 open position and the gripping position, plus a gripping over-stroke of approximately 1.5 before reaching the fully gripped position. Jaws have to be designed for a gripping position (parallel jaws) Style-CT ngular Gripper Style: CT-5M Size -5M Stroke: 9 each finger Grip Force: 16 lbs 651 m Weight:. lbs 1.82 Kg Page 2.
NGULR GRIPPER DCT-12M 18 SERIES Shielded plate 18 6..71.236 Jaws in gripping position at 25.98 1.39 1.6.63 [6. g6] -.2.2362 -.5 2 x [M3] THRU [ 2.5E7] THRU 36.5 1.37 9 9 DCT SERIES 2.3 2x[ 2.5H9 x.5 DP] x [M3 x 7 DP] 2x[ 9.5.375 3H7 x 6 DP] 2 x [M3 x 7 DP] 1.5.579 12.5.921 6 2.52 56. 2.27 8 1.89 16.5.65 35.5 1.398 19.5.75 2.5.966 2..787 Specifications DCT-12M Total Rated Grip Force, F @ 1 psi [7 bar] L = 1 in. [25mm] @... 7.2 lbs. 32 N Stroke... 9 of stroke for each finger Weight....2 lbs..9 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø....72 in. 12 mm Displacement....117 in 3. 1.92 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....6 sec..6 sec. ccuracy... ±.28 in. ±.7 mm Repeatability... ±.2 in. ±.5 mm Valve required to actuate... -way, 2-position 8.31 Side air port Side air port 9 [M5 x 6 DP].35 [M5 x6dp] Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. Gripper's top air port 3.12 5.2.8.3 O-Ring [ 1 x 3] Top air port [M3 x 5.5 DP] (supplied plugged) 2x[ 2.5H9 x.5 DP] 2.79 9.35 Top air port [M3 x 5.5 DP] (supplied plugged) 2 Slots to mount magnetic sensors 3 1.18 2.5.966 9.35 8.6.339 VIEW - 2x[M3 x7dp] 1.5.579 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) TM FINGER FORCE - F/2 N 16 12 8 lbs. 3 2 1 1 1.5 2. 2.5 in. 25 35 5 65mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER @ 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/ 2 Mz F/ 2 My X NOTE: DCT-12 can be used as an exact replacement for CT-12 BSIC MODEL DCT -12M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-159 1 Viton Seal Repair Kit SLKT-159V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT12-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 11 lbs. 7 N 2 lbs. 9. N Maximum Compressive C 11 lbs. 7 N 2 lbs. 9. N Maximum Moment Mx 1 in.-lbs. 1.1 Nm 3 in.-lbs..3 Nm Maximum Moment My 1 in.-lbs. 1.1 Nm 3 in.-lbs..3 Nm Maximum Moment Mx 1 in.-lbs. 1.1 Nm 3 in.-lbs..3 Nm Capacities are per set of jaws and are not simultaneous.31 [8].2 [5] M.59 [15] MX. DJUSTBLE STOP KIT (BR)
NGULR GRIPPER DCT-16M 18 SERIES Shielded plate 2.79 Jaws in gripping position at 8..315 26.5 1.3 2.8 1.39 [8g6] -.2.315 -.6 2x[M3] THRU [ 2.5E7] THRU 9.5 1.59 9 2x[ 3H9 x 5.5 DP] x [M3 x 7 DP] 2 x [ 3H7 x 6 DP] 9.5 C.375 L 2x[Mx9DP] 19.5.75 29. 1.117 18..787 1..5512 2..787 72 2.83 6. 2.5197 56 2.2 Side air port [M5 x6dp] 1.39 2.5.87 8.31 Side air port [M5x6DP] 9.35 23.5.925 x[m3x5.5dp] 17.67 1.5 1.63 2 Slots to mount magnetic sensors DCT SERIES 2.35 Specifications DCT-16M Total Rated Grip Force, F @ 1 psi [7 bar] L = 1 in. [25mm] @... 16 lbs. 7 N Stroke... 9 of stroke for each finger Weight....35 lbs..16 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø....63 in. 16 mm Displacement....251 in 3..12 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....13 sec..13 sec. ccuracy... ±.28 in. ±.7 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. 3.12 5.2 Gripper's top air port.8.3 O-Ring [ 1 x 3] Top air port [M3 x 5.5 DP] (supplied plugged) 2x[ 3H9x6DP] 25.98 1.39 Top air port [M3 x 5.5 DP] (supplied plugged) 11.5.53 36 1.2 29. 1.117 9.35 VIEW - 2x[M x9dp] 18..787 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 3 2 1 lbs. 9 7 2 1 1.25 1.5 1.75 2. 2.25 2.5 2.75 in. 25 32 38 51 57 6 7mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER @ 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/ 2 Mz F/ 2 My X NOTE: DCT-16 can be used as an exact replacement for CT-16 BSIC MODEL DCT -16M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT16-2 1 mm PNP Inductive Sensor with Quick Disconnect* OISP-1 1 or 2 mm NPN Inductive Sensor with Quick Disconnect* OISN-1 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-16 1 Viton Seal Repair Kit SLKT-16V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT16-BR 1 *Sensor and cable sold separately. TM Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 2 lbs. 9 N lbs. 18 N Maximum Compressive C 2 lbs. 9 N lbs. 18 N Maximum Moment Mx 26 in.-lbs. 2.9 Nm 6 in.-lbs..7 Nm Maximum Moment My 26 in.-lbs. 2.9 Nm 6 in.-lbs..7 Nm Maximum Moment Mz 26 in.-lbs. 2.9 Nm 6 in.-lbs..7 Nm Capacities are per set of jaws and are not simultaneous.39 [1].2 [6] M5.79 [2] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).31 [8].16 [] 1.79 [5.5].59 [15].81 [2.5].2 [6] Sensors.8 [12.3] Ø.16 [].6 [11.7].22 [5.5]
NGULR GRIPPER DCT-2M 18 SERIES Shielded plate 22.87 Jaws in gripping position at 1..39 33 1.3 12.7 2.6.12 [1g6] -.2.3937 -.6 2x[M] THRU [ 3E7] THRU 9.5 1.99 9 9 DCT SERIES 2.36 2x[ H9 x 8 DP] 89 3.5 x [M3 x 6 DP] 21.5.865 9.5.375 x[m5 x 6 DP] 2x[ 3H7 x 6 DP] 18..787 79. 3.112 68 2.68 2.5.965 9.35 29 1.1 51.5 2.28 19.5.75 33.5 1.3189 22..8661 Specifications DCT-2M Total Rated Grip Force, F @ 1 psi [7 bar] L = 1.25 in. [32mm] @... 25 lbs. 112 N Stroke... 9 of stroke for each finger Weight....62 lbs..28 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø....787 in. 2 mm Displacement....83 in 3. 7.92 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....16 sec..16 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.2 in. ±.5 mm Valve required to actuate... -way, 2-position C 8 L.31 Side air port [M5 x6dp] 11 Side air port.3 [M5 x6dp] Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. Gripper's top air port 3.12 5.2.8.3 O-Ring [ 1 x 3] x[m3x5.5dp] Top air port [M3 x 5.5 DP] (supplied plugged) 2x[ H9 x 8 DP] 3 1.18 11.3 Top air port [M3 x 5.5 DP] (supplied plugged) 22.87 2 1.65 33.5 1.3189 13.5.531 1.39 2 Slots to mount magnetic sensors 2x[M5 x11dp] VIEW - 21.5.865 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) TM FINGER FORCE - F/2 N 6 5 3 2 1 lbs. GRIP FORCE PER FINGER @ 13 WRNING! 11 DO NOT EXCEED MXIMUM EFFECTIVE 9 FINGER LENGTHS 7 2 1.25 1.75 2.25 2.75 3.25 in. 32 57 7 83mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx F/ 2 Mz F/ 2 My X NOTE: DCT-2 can be used as an exact replacement for CT-2 BSIC MODEL DCT -2M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT M8 PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 M8 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT16-2 1 mm PNP Inductive Sensor with Quick Disconnect* OISP-1 1 or 2 mm NPN Inductive Sensor with Quick Disconnect* OISN-1 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-161 1 Viton Seal Repair Kit SLKT-161V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT2-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 3 lbs. 15 N 7 lbs. 3 N Maximum Compressive C 3 lbs. 15 N 7 lbs. 3 N Maximum Moment Mx 53 in.-lbs. 6 Nm 13 in.-lbs. 1.5 Nm Maximum Moment My 53 in.-lbs. 6 Nm 13 in.-lbs. 1.5 Nm Maximum Moment Mz 53 in.-lbs. 6 Nm 13 in.-lbs. 1.5 Nm Capacities are per set of jaws and are not simultaneous.7 [12].31 [8] M6.98 [25] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).31 [8].1 [3.5] 2.2 [56].59 [15] 1.2 [26].2 [6] Sensors.8 [12.3] Ø.16 [].6 [11.7].8 [8]
NGULR GRIPPER DCT-25M 18 SERIES Jaws in gripping position at Shielded plate 26 1.2 12.7 3.3.13 -.2 15.72 -.7.59 2 x [M5] [12g6] [ E7].1575 SF 59 2.32 9. 1.57 9 x [M5 x 11 DP] 2 x [ 5H7 x 1 DP] 19.1.75 38.1 1.5 (Dowels) 3. 1.1811 Specifications DCT-25M Total Rated Grip Force, F @ 1 psi [7 bar] L = 1.75 in. [mm] @... 35 lbs. 157 N Stroke... 9 of stroke for each finger Weight... 1.8 lbs..9 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø....98 in. 25 mm Displacement....99 in 3. 1.9 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....21 sec..21 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate... -way, 2-position 16.17 93.5 3.6811 81 3.19 [M5 x 6 DP] 11.3 28.5 1.122 1.39 [M5 x 6 DP] Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. Gripper's top air port.16 8.31 1.2.5 O-Ring [ 1.5 x 5] 2 x [ 5H7 x 1 DP] [M5 x 6 DP] (supplied plugged) [ 5H9] 2 x.1969 SF x.39 [1] DP 36 1.2 11.3 39.5 1.555 x [M3 x 7 DP] [M5 x 6 DP] (supplied plugged) 17.5.689 26.5 1.3 5. 1.97 12.7. 1.578 26. 1.2 2..79 61 2. 2 Slots to mount magnetic sensors 2 x [M6 x 13 DP] VIEW - 26. 1.236 DCT SERIES 2.37 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 8 6 2 lbs. 18 13 9 1.75 2.25 2.75 3.25 3.75.25 in. 57 7 81 95 18mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER @ 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/ 2 Mz F/ 2 My X BSIC MODEL DCT -25M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT25-32 1 M8 PNP Inductive Sensor with Quick Disconnect* OISP-11 1 or 2 M8 NPN Inductive Sensor with Quick Disconnect* OISN-11 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES M5 djustable Flow Control VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-162 1 Viton Seal Repair Kit SLKT-162V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT25-BR 1 *Sensor and cable sold separately. TM Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 6 lbs. 25 N 9 lbs. 1 N Maximum Compressive C 6 lbs. 25 N 9 lbs. 1 N Maximum Moment Mx 89 in.-lbs. 1 Nm 22 in.-lbs. 2.5 Nm Maximum Moment My 89 in.-lbs. 1 Nm 22 in.-lbs. 2.5 Nm Maximum Moment Mz 89 in.-lbs. 1 Nm 22 in.-lbs. 2.5 Nm Capacities are per set of jaws and are not simultaneous.55 [1].39 [1] M6 1.18 [3] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).3 [11].18 [.5] 2.62 [66.5].63 [16] 1.38 [35.2].39 [1] Sensors.79 [2] Ø.31 [8].63 [16].37 [9.5]
NGULR GRIPPER CT-32M 18 SERIES CT SERIES 2.38 Shielded plate +.3 6 +.12 2 x.2362. x.7 [12] DP 2 x M8 x.67 [17] DP 28 1.1 Jaws in gripping position at 1.551 5 1.77 12.88 29 ±.16 1.117 ±.6 -.6 1 -.17 -.2.5512 -.7 3.9.15 11 ±.11.337 ±.3 17 =.67 = 95 3.7 2 x M6 +.32 5 +.2 +.13.1969 +.8 33 1.3 7.5.3 51.5 2.3 67 2.6 9 9 73 2.87 3 ±.19 1.6929 ±.7 25 ±.26.983 ±.1 Side air port M5 x.2 [6] DP 12.7 12.7 Side air port M5 x.2 [6] DP x [M3 x 7] 31.5 1.2 2 Slots to mount magnetic sensors Specifications CT-32M Total Rated Grip Force, F @ 1 psi [7 bar] L = 1.75 in. [mm] @... 61 lbs. 272 N Stroke... 9 of stroke for each finger Weight... 1.59 lbs..72 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø... 1.26 in. 32 mm Displacement... 1.75 in 3. 28.6 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....29 sec..29 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.2 in. ±.5 mm Valve required to actuate... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. Gripper's top air port 1.2.5.16 8 O-Ring.31 [ 1.5 x 5] +.3 6 +.12 2 x.2362. x.7 [12] DP Top air port M5 x.2 [6] DP (supplied plugged) 2 1.65 12.7 Top air port M5 x.2 [6] DP (supplied plugged) 56 2.2 3 ±.19 1.6929 ±.7 21.5.85 19.75 VIEW - 2 x M8 x.67 [17] DP 29 ±.16 1.117 ±.6 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 1 12 1 8 6 2 lbs. GRIP FORCE PER FINGER @ 31 WRNING! 27 DO NOT EXCEED MXIMUM EFFECTIVE 22 FINGER LENGTHS 18 13 9 1.75 2.25 2.75 3.25 3.75.25.75 5.25 in. 57 7 81 95 18 12 133mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx F/ 2 Mz F/ 2 My X BSIC MODEL CT -32M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT25-32 1 M8 PNP Inductive Sensor with Quick Disconnect* OISP-11 1 or 2 M8 NPN Inductive Sensor with Quick Disconnect* OISN-11 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-163 1 Viton Seal Repair Kit SLKT-163V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT32-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 65 lbs. 288 N 13 lbs. 57.6 N Maximum Compressive C 65 lbs. 288 N 13 lbs. 57.6 N Maximum Moment Mx 12 in.-lbs. 16 Nm 35 in.-lbs. Nm Maximum Moment My 12 in.-lbs. 16 Nm 35 in.-lbs. Nm Maximum Moment Mz 12 in.-lbs. 16 Nm 35 in.-lbs. Nm Capacities are per set of jaws and are not simultaneous.63 [16].7 [12] M8 1. [35] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).3 [11].16 [] 3.11 [79].63 [16] 1.86 [7.2].39 [1] Sensors.79 [2] Ø.31 [8].63 [16].7 [12]
NGULR GRIPPER CT-M 18 SERIES Shielded plate 3 1.3 Jaws in gripping position at 16.63 9 1.93 3.9.15 17.67 [16g6] -.2.6299 -.7 2 x [M6] [ 5E7].1969 SF 7.5 2.933 9 9 [ 6H9] 2 x.2362 SF x.7 [12] DP 2 x [M8 x 17 DP] 138 5.3 39. 1.535 12..8819 17.5.232 39.5 1.555 2.79 5.5 1.988 81.5 3.29 CT SERIES 2.39 53. 2.866 26. 1.236 [G 1/8 x 8 DP] 18.71 12.7 [G 1/8 x 8 DP] x [M x 8 DP] 51 2.1 2 Slots to mount magnetic sensors Specifications CT-M Total Rated Grip Force, F @ 1 psi [7 bar] L = 2 in. [51mm] @... 1 lbs. 6 N Stroke... 9 of stroke for each finger Weight... 2.6 lbs. 1.18 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø... 1.575 in. mm Displacement... 3.173 in 3. 52 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....1 sec..1 sec. ccuracy... ±.36 in. ±.9 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. Gripper's top air port.16 1.2.5 8 O-Ring.31 [ 1.5 x 5] [ 6H9] 2 x.2362 SF x.7 [12] DP [M5 x 6 DP] (supplied plugged) 52 2.5 18.71 [M5 x 6 DP] (supplied plugged) 66 2.6 53. 2.866 25.5 1. 18.71 VIEW - 2 x [M8 x 17 DP] 39. 1.535 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 25 2 15 1 5 lbs. 56 5 3 22 11 2 3 5 6 in. 51 76 12 127 152mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER @ 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/ 2 Mz F/ 2 My X BSIC MODEL CT -M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SCT-63 1 M12 PNP Inductive Sensor with M12 Quick Disconnect* OISP-17 1 or 2 M12 NPN Inductive Sensor with M12 Quick Disconnect* OISN-17 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 M12 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M12 Quick Disconnect 5 Meter Cable Length * CBL-18 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control G1/8 Elbow - 6mm OD Push-in (Metric) VLVF-5 1 or 2 Buna-NSeal Repair Kit SLKT-16 1 Viton Seal Repair Kit SLKT-16V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-CT-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 9 lbs. 2 N 19 lbs. 8 N Maximum Compressive C 9 lbs. 2 N 19 lbs. 8 N Maximum Moment Mx 195 in.-lbs. 22 Nm 9 in.-lbs. 5.5 Nm Maximum Moment My 195 in.-lbs. 22 Nm 9 in.-lbs. 5.5 Nm Maximum Moment Mz 195 in.-lbs. 22 Nm 9 in.-lbs. 5.5 Nm Capacities are per set of jaws and are not simultaneous.63 [16].7 [12] M8 1.57 [] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).69 [17.5].22 [5.5] 3.5 [89] 1.18 [3] 1.79 [5.5].39 [1] Sensors.87 [22] Ø.7 [12].83 [21].57 [1.5]
NGULR GRIPPER CT-5M 18 SERIES Shielded plate 18 1.57.71 Jaws in gripping position at 6 2.36 5.2 21.83 [18g6] -.2.787 -.7 2 x [M8] [ 6E7].2362 SF 9 3.5 9 9 CT SERIES 2. [ 8H9] 2 x.315 SF x.63 [16] DP 2 x [M1 x 22 DP] 6. 2.3622 6. 1.811 16 6.6 3. 1.1811 16. 5.78 126.96 [G 1/8 x 8 DP] CL 25.98 1.73 15.59 [G 1/8 x 8 DP] 2.79 65.5 2.579 x [M x 8 DP] 6 2.36 96 3.78 2 Slots to mount magnetic sensors Specifications CT-5M Total Rated Grip Force, F @ 1 psi [7 bar] L = 2.25 in. [6mm] @... 16 lbs. 651 N Stroke... 9 of stroke for each finger Weight....1 lbs. 1.82 Kg Pressure Range... -1 psi 3-7 Bar Cylinder Bore Ø... 1.968 in. 5 mm Displacement... 5.61 in 3. 92 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation....6 sec..6 sec. ccuracy... ±.36 in. ±.9 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown..1 8.31 Gripper's top air port 1.2.5 O-Ring [Ø1.5 x Ø5 ] [ 8H9] 2 x.315 SF x.63 [16] DP [M5 x 6 DP] (supplied plugged) 62 2. 25.98 [M5 x 6 DP] (supplied plugged) 76 2.99 6. 2.3622 3 1.18 3 1.18 2 x [M1 x 21 DP] VIEW - 6. 1.811 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 3 25 2 15 1 5 lbs. GRIP FORCE PER FINGER @ 67 56 5 WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS 3 22 11 2.5 3.5.5 5.5 6.5 7.5 8.5 in. 6 89 12 1 165 191 216mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] C Y T Mx F/ 2 Mz F/ 2 My X BSIC MODEL CT -5M - V SIE VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT M8 PNP Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSP-17 1 or 2 M8 NPN Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT-63 1 M12 PNP Inductive Sensor with M12 Quick Disconnect* OISP-17 1 or 2 M12 NPN Inductive Sensor with M12 Quick Disconnect* OISN-17 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 M12 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M12 Quick Disconnect 5 Meter Cable Length * CBL-18 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control G1/8 Elbow - 6mm OD Push-in (Metric) VLVF-5 1 or 2 Buna-NSeal Repair Kit SLKT-165 1 Viton Seal Repair Kit SLKT-165V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-CT5-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 11 lbs. 9 N 22 lbs. 98 N Maximum Compressive C 11 lbs. 9 N 22 lbs. 98 N Maximum Moment Mx 266 in.-lbs. 3 Nm 66 in.-lbs. 7.5 Nm Maximum Moment My 266 in.-lbs. 3 Nm 66 in.-lbs. 7.5 Nm Maximum Moment Mz 266 in.-lbs. 3 Nm 66 in.-lbs. 7.5 Nm Capacities are per set of jaws and are not simultaneous.79 [2].63 [16] M1 1.77 [5] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).69 [17.5].2 [5].9 [1] 1.18 [3] 2.38 [6.5].39 [1] Sensors.87 [22] Ø.7 [12].83 [21].75 [19]
DCT/CT SERIES EXPLODED VIEW 7 2 9 8 1 1 3 5 5 6 x2 x2 x2 x2 x2 Item Qty Name 1 1 Body 2 1 Driver 3 1 Piston 2 Jaw 5 1 Washer 6 1 Cap 7 1 Shielded Plate 8 2 Wiper Cover 9 2 Drive Pin 1 2 Pivot Pin 5 1 Magnet NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. ssembly Procedure 1) Lubricate and install the seals into cap (x1), piston (x2) and body (x1) 2) If top air ports are used, clear them and plug the side air ports on the body (#1) 3) Lubricate the sloping rack of jaws (#) ) Install both drive pins (#9) into driver (#2) through sloping racks of jaws. Check that the pin flat surface is correctly aligned before continuing with their installation. 5) Lock drive pins in the driver with screws, tightening down on to the flat surface of the pins. 6) Position driver and jaws assembly into body. 7) Install both pivot pins (#1) into body, through the bore of jaws. Check that the pin flat surface is correctly aligned before continuing with their installation. 8) Pivot pin locking: - DCT-12 (not shown): lock pivot pins into body with screws, tightening down on to the flat surface of the pins (pins are fixed into body and rotating into jaws) - DCT-16 to CT-5: lock pivot pins into jaws with screws, tightening down on to the flat surface of the pins (pins are fixed into jaws and rotating into body) 9) Magnet mounting: - DCT-12 to DCT-2: install the magnet (#5) on the washer (#5) - DCT-25 to CT-5 (not shown): install magnet (#5) onto piston (#3) and lock it by means of its retaining ring. 1) Piston mounting: - DCT-12 to DCT-2: insert the piston and the washer with magnet into body. Fix the assembly at the end of the driver with screw. - DCT-25 to CT-5 (not shown): insert the piston with magnet into body. Fix the assembly at the end of the drivers with screw. 11) Check unit operation unladen. 12) Install the cap (#6) into body and lock it by means of its retaining ring. 13) Place both wiper covers (#8) into body and lock them with their screws. 1) Fix the shielded plate (#7) onto body with both screws. DCT/CT SERIES MINTENNCE 2.1 SK Seal Repair Kit Order # s Product Data Sheets SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
DCT/CT SERIES SSEMBLED VIEW DCT/CT SERIES MINTENNCE 2.2 1 8 5 6 5 3 9 Item Qty Name 1 1 Body 2 1 Driver 3 1 Piston 2 Jaw 5 1 Washer 6 1 Cap 7 1 Shielded Plate 8 2 Wiper Cover 9 2 Drive Pin 1 2 Pivot Pin 5 1 Magnet NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. 1 2 7 CCESSORY INSTLLTION & DJUSTMENT INSTRUCTIONS DCT16M, 2M DCT25M, 32M CTM, 5M 3 1 1 1 2 2 2 5 2 7 6 1 6 6 7 5 3 3 8 8 5 8 3 Installation - djustment Stop 1) Unscrew both screws for mounting of the shielded plate and remove it. 2) Fix the new shielded plate (#1) and the stop (#2) onto body with both screws (#3) 3) Install the locknut system (#) and (#5) on the stop. ) Tighten screw for maximum target jaw opening and lock with locknut. Installation - Inductive Sensor Holders 1) Fix the flags (#1) at the end of pivot pins with their screws (#2) 2) Holder mounting: - DCT-16M to DCT-32M: fix holder (#3) and spacer (#5) onto body with both screws (#6) - DCT-M to DCT-5M: fix holder (#3) onto body with both screws (#6) 3) Sensor mounting: - DCT-16M to DCT-2M: unscrew lightly both screws for mounting (#6) of holder and insert sensor (#8, not included) into it. Position sensor so that it senses up on flag. Lock the sensor by tightening both screws. - DCT-25M to DCT-32M: unscrew lightly screw (#7) on holder and insert sensor (#8, not included) into it. Position sensor so that it senses up the flag. Lock the sensor by tightening screw. - CT-M to CT-5M: insert sensor (#8, not included) in stop into holder. Lock the sensor by tightening the collar holder with both screws (not shown). ) djust flag position by unscrewing their screws for desired sensing positions. SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
QULITY PRECISION DESIGNDURBILITY NOTES PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY 2.3 PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DCT/CT SERIES MINTENNCE
DCT-RE/CT-RE SERIES ngular Grippers- 18 Spring ssist Series 2. 18 angular gripper: The full jaw opening (18 ) means that the part can be direct fed, avoiding any release movement by the robot or by the actuator. Multiple mounting locations: DIRECTCONNECT mounting on back of body (sizes 12-25). Standard mounting on top. Fail safe operation: The force supplied from the internal spring can be used to maintain gripping force if the gripper looses air pressure. Compact gripper: This gripper is designed for use in confined spaces. Multipurpose gripper: Several accessories (adjustable stop, magneto resistive or inductive sensors) allow this gripper to be used in a number of applications. Harsh environments: Shielded design repels chips and other particulate from internal drive mechanism. TM Mounting Information: Gripper can be mounted and operated in any orientation Gripper is located from the top with 2 dowel pins and assembled with 2 screws. G DIRECTCONNECT mounting pattern: Gripper is located with 2 dowel pins and assembled with screws. lternative pattern: Gripper is located with 2 dowel pins and assembled with 2 screws. The gripper is protected from falling debris when it is mounted and operated upside down. Technical Specifications: Pneumatic Specifications Imperial Metric Pressure Operating Range 6-1 psi -7 bar Cylinder Type Double cting Spring ssist or Single cting Spring Return Dynamic Seals Internally Lubricated Buna-N Valve Required to Operate -way, 2-position ir Quality Requirements ir Filtration ir Lubrication ir Humidity Micron or Better Not Necessary* Low Moisture Content (dry) Temperature Operating Range Buna-N Seals (Standard) -3 ~18 F -35 ~8 C Viton Seals (Optional) -2 ~3 F -3 ~15 C Maintenance Specifications Expected Life Normal pplication 5 million cycles w/ Preventative Maintenance 1+ million cycles* Field Repairable Yes Seal Repair Kits vailable Yes *ddition of lubrication will greatly increase service life Maintenance Section Fingers are centered over the jaws, located with 1 dowel pin and assembled with 2 screws. Gripper can be operated utilizing top manifold air ports.
Gripper ttachment Gripper mounting from side or bottom Viton Seals Viton seals for high temperatures (-2 F to +3 F / -3 ~15 C) are optional Quality Components Made from aluminum alloy anodized with Teflon impregnation. The gripper's main components are made of heat treated steel. Inductive Sensor Mounting Kit ccessory (SD) in order to control jaw position: comes with 2 holders for tubular sensors and 2 adjustable flags (except size -12) Magneto Resistive Sensor Mounting Kit The gripper comes with adjustable slots for the 2 magnetic sensors (to control jaw position) Jaw Driver Drive Pin Body Cap Product Features Operating Principle djustable Stop ccessory (BR) in order to adjust the opening of jaws, between to 18 Piston Shielded Plate and Wiper Covers Gripper body is shielded to repel chips and other particulate from internal drive mechanism Mounting Patterns DIRECTCONNECT mounting surface on back of body (sizes 12-25) Fail Safe Spring Internal spring allows the gripper to hold onto part with loss of air pressure Shielded Plate Drive Pin Slot Magnet Pivot Pin Wiper Cover Multiple ir Ports Side or top air ports (top ports require O-ring) Fail Safe Spring Style -DCT-RE ngular Gripper Size -12M Style: DCT-12M-RE Stroke: 9 each finger Grip Force: 9 lbs N Weight:.26 lbs.12 Kg Page 2.6 Style -DCT-RE ngular Gripper Size -16M Style: DCT-16M-RE Stroke: 9 each finger Grip Force: 19 lbs 87 N Weight:. lbs.2 Kg Page 2.7 Style -DCT-RE ngular Gripper Size -2M Style: DCT-2M-RE Stroke: 9 each finger Grip Force: 32 lbs 11 N Weight:.73 lbs.33 Kg Page 2.8 Style -DCT-RE ngular Gripper Size -25M Style: DCT-25M-RE Stroke: 9 each finger Grip Force: 5 lbs 199 Nm Weight: 1.26 lbs.57 Kg Page 2.9 Style -CT-RE ngular Gripper Size -32M Style: CT-32M-RE Stroke: 9 each finger Grip Force: 79 lbs 353 N Weight: 1.83 lbs.83 Kg Page 2.5 Style -CT-RE ngular Gripper Size -M Style: CT-M-RE Stroke: 9 each finger Grip Force: 133 lbs 592 N Weight: 3.6 lbs 1.39 Kg Page 2.51 DCT-RE/CT-RE SERIES 2.5 TM Exhaust Pressure Pressure Exhaust double acting piston, with a ring magnet for magneto resistive sensing, is connected to a fork driver on which 2 drive pins are fixed. Jaw rotation is synchronized with the drive pin-jaw assembly. Sliding in these slots, drive pins convert vertical motion of the piston into rotating opposite synchronous motion of both jaws. Each jaw has a useful rotation stroke of 9, between the 9 open position and the gripping position, plus a gripping over-stroke of approximately 1.5 before reaching the fully gripped position. Jaws have to be designed for a gripping position (parallel jaws) The fail safe spring allow the gripper to retain the component should the air supply fail or for the gripper to be used in single acting mode. Style -CT-RE ngular Gripper Size -5M Style: CT-5M-RE Stroke: 9 each finger Grip Force: 21 in-lbs 893 N Weight:.87 lbs 2.21 Kg Page 2.52
NGULR GRIPPER DCT-12M-RE 18 SERIES Shielded plate 18.71 Jaws in gripping position at 6..236 25.98 1.39 1.6.63 [6g6] -.2.2362 -.5 2x[M3] THRU [ 2.5E7] THRU 36.5 1.37 9 9 DCT-RE SERIES 2.6 x [M3 x 7 DP] 2x[ 3H7 x 6 DP] 9.5.375 2x[ 2.5H7 x.5 DP] 2x[M3 x 7 DP] 1.5.579 35. 1.378 8 3.15 72. 2.836 6 2.52 16.5.65 51.5 2.28 12.5.921 8.31 19.5.75 2.5.966 Specifications DCT-12M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 1 in. [25mm] @... 9 lbs. N Stroke... 9 of stroke for each finger Weight....26 lbs..12 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø....72 in. 12 mm Displacement....117 in 3. 1.92 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....8 /.5 sec. ccuracy... ±.28 in. ±.7 mm Repeatability... ±.2 in. ±.5 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Side air port [M5 x6dp] 9.35 Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. 3.12 5.2 Gripper's top air port.8.3 O-Ring [ 1 x 3] Side air port [M5 x6dp] Top air port [M3 x 5.5 DP] (supplied plugged) 2x[ 2.5H9 x.5 DP] 2.79 Top air port [M3 x 5.5 DP] (supplied plugged) 2 Slots to mount magnetic sensors 9.35 3 1.18 2.5.966 9.35 8.6.339 VIEW - 2x[M3 x7dp] 1.5.579 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) TM FINGER FORCE - F/2 N 2 16 12 8 lbs. 5 3 2 1 1 1.5 2. 2.5 3 in. 25 35 5 6 76mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER @ WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] 2 PSI [1.3 bar] C PSI [ bar] T Y Mx F/ 2 Mz My F/ 2 X NOTE: DCT-12-RE can be used as an exact replacement for CT-12-RE BSIC MODEL DCT - 12M - RE - V SIE SPRING VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-159 1 Viton Seal Repair Kit SLKT-159V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT12-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 11 lbs. 7 N 2 lbs. 9. N Maximum Compressive C 11 lbs. 7 N 2 lbs. 9. N Maximum Moment Mx 1 in.-lbs. 1.1 Nm 3 in.-lbs. 1.1 Nm Maximum Moment My 1 in.-lbs. 1.1 Nm 3 in.-lbs. 1.1 Nm Maximum Moment Mz 1 in.-lbs. 1.1 Nm 3 in.-lbs. 1.1 Nm Capacities are per set of jaws and are not simultaneous.31 [8].2 [5] M.59 [15] MX. DJUSTBLE STOP KIT (BR)
NGULR GRIPPER DCT-16M-RE 18 SERIES Shielded plate 2.79 Jaws in gripping position at 8..315 26.5 1.3 1.39 2.8 [8g6] -.2.315 -.6 2x[M3] THRU [ 2.5E7] THRU.5 1.59 9 9 x [M3 x 7 DP] 2x[ 3H7 x 6 DP] 9.5.375 2x[ 3H9 x 5.5 DP] 2x[Mx9DP] 18..787 1..5512 87 3.3 79. 3.112 71 2.8 2.5.87 9.35 38.5 1.516 56.5 2.22 DCT-RE SERIES 2.7 19.5.75 29. 1.117 35. 1.378 Side air port [M5 x 6 DP] 1.39 8.31 Side air port [M5 x6dp] x [M3 x 5.5 DP] 17.67 2 Slots to mount magnetic sensors Specifications DCT-16M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 1 in. [25mm] @... 19 lbs. 87 N Stroke... 9 of stroke for each finger Weight.... lbs..2 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø....63 in. 16 mm Displacement....251 in 3..12 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....15 /.12 sec. ccuracy... ±.28 in. ±.7 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. 3.12 5.2 Gripper's top air port.8.3 O-Ring [ 1 x 3] Top air port [M3 x 5.5 DP] (supplied plugged) 2x[ 3H9 x 5.5 DP] 25.98 1.39 Top air port [M3 x 5.5 DP] (supplied plugged) 36 1.2 29. 1.117 11.5.53 VIEW - 9.35 2x[M x9dp] 18..787 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 5 3 2 1 lbs. 11 9 7 2 1 1.5 2. 2.5 3 in. 25 35 5 6 76mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L GRIP FORCE PER FINGER @ WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] 2 PSI [1.3 bar] PSI [ bar] C Y T Mx F/ 2 Mz F/ 2 My X NOTE: DCT-16-RE can be used as an exact replacement for CT-16-RE BSIC MODEL DCT - 16M - RE - V SIE SPRING VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT16-2 1 mm PNP Inductive Sensor with Quick Disconnect* OISP-1 1 or 2 mm NPN Inductive Sensor with Quick Disconnect* OISN-1 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-16 1 Viton Seal Repair Kit SLKT-16V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT16-BR 1 *Sensor and cable sold separately. TM Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 2 lbs. 9 N lbs. 18 N Maximum Compressive C 2 lbs. 9 N lbs. 18 N Maximum Moment Mx 26 in.-lbs. 2.9 Nm 6 in.-lbs..7 Nm Maximum Moment My 26 in.-lbs. 2.9 Nm 6 in.-lbs..7 Nm Maximum Moment Mz 26 in.-lbs. 2.9 Nm 6 in.-lbs..7 Nm Capacities are per set of jaws and are not simultaneous.39 [1].2 [6] M5.79 [2] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).31 [8].16 [] 2.38 [6.5].59 [15] 1. [35.5].2 [6] Sensors.8 [12.3] Ø.16 [].6 [11.7].22 [5.5]
NGULR GRIPPER DCT-2M-RE 18 SERIES Shielded plate 22.87 Jaws in gripping position at 1..39 33 1.3 12.7 2.6.12 [1g6] -.2.3937 -.6 2x[M] THRU [ 3E7] THRU 9.5 1.99 9 9 DCT-RE SERIES 2.8 x[m3 x 6 DP] 2x[ H9 x 8 DP] 9.5.375 2x[ 3H7 x 6 DP] 2 x [M5 x 11 DP] 21.5.865 2..787 1.9 9. 3.78 83 3.27 25.96 9.35 7 1.85 66.5 2.618 19.5.75 33.5 1.3189 39. 1.535 Specifications DCT-2M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 1.25 in. [32mm] @... 32 lbs. 11 N Stroke... 9 of stroke for each finger Weight....73 lbs..33 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø....787 in. 2 mm Displacement....83 in 3. 7.92 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....2 /.1 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.2 in. ±.5 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Side air port [M5 x 6 DP] CL 11.3 Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. 3.12 5.2 Gripper's top air port.8.3 8.31 Side air port [M5 x6dp] O-Ring [ 1 x 3] x[m3x5.5dp] Top air port [M3 x 5.5 DP] (supplied plugged) 2x[ H9 x 8 DP] 3 1.18 11.3 Top air port [M3 x 5.5 DP] (supplied plugged) 22.87 2 1.65 33.5 1.3189 13.5.531 2 Slots to mount magnetic sensors 2x[M5 x11dp] 1 VIEW -.39 21.5.865 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) TM FINGER FORCE - F/2 N 7 6 5 3 2 1 lbs. GRIP FORCE PER FINGER @ 16 13 11 WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS 9 7 2 1.25 1.75 2.25 2.75 3.25 in. 32 57 7 83mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] 2 PSI [1.3 bar] PSI [ bar] C Y T Mx F/ 2 Mz F/ 2 My X NOTE: DCT-2-RE can be used as an exact replacement for CT-2-RE BSIC MODEL DCT - 2M - RE - V SIE SPRING VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT16-2 1 mm PNP Inductive Sensor with Quick Disconnect* OISP-1 1 or 2 mm NPN Inductive Sensor with Quick Disconnect* OISN-1 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-161 1 Viton Seal Repair Kit SLKT-161V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT2-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 3 lbs. 15 N 7 lbs. 3 N Maximum Compressive C 3 lbs. 15 N 7 lbs. 3 N Maximum Moment Mx 53 in.-lbs. 6 Nm 13 in.-lbs. 1.5 Nm Maximum Moment My 53 in.-lbs. 6 Nm 13 in.-lbs. 1.5 Nm Maximum Moment Mz 53 in.-lbs. 6 Nm 13 in.-lbs. 1.5 Nm Capacities are per set of jaws and are not simultaneous.7 [12].31 [8] M6.98 [25] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).31 [8].1 [3.5] 2.79 [71].59 [15] 1.73 [].2 [6] Sensors.8 [12.3] Ø.16 [].6 [11.7].8 [8]
NGULR GRIPPER DCT-25M-RE 18 SERIES Shielded plate 26 1.2 Jaws in gripping position at 12.7 3.3.13 15.59 [12g6] -.2.72 -.7 2 x [M5] [ E7].1575 SF 59 2.32 9 9 x [M5 x 11 DP] 19.1.75 2 x [ 5H7 x 1 DP] 38.1 1.5 (Dowels) 2x[ 5 H9 x1dp] 51. 2.79 127 5. 11.5.579 12.2 [M5 x 6 DP] 11.3 28.5 1.122 1.39 [M5 x 6 DP] 7.5.295 6.5 2.382 x [M3 x 7 DP] 26.5 1.3 26. 1.2 25..98 82 3.23 2 Slots to mount magnetic sensors DCT-RE SERIES 2.9 Specifications DCT-25M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 1.75 in. [mm] @... 5 lbs. 199 N Stroke... 9 of stroke for each finger Weight... 1.26 lbs..57 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø....98 in. 25 mm Displacement....99 in 3. 1.9 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....25 /.19 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown. 3.12 5.2 Gripper's top air port.8.3 O-Ring [ 1 x 3] [ 5H9] 2 x.1969 SF x.39 [1] DP [M5 x 6 DP] (supplied plugged) 36 1.2 11.3 [M5 x 6 DP] (supplied plugged). 1.57. 1.578 17.5.689 12.7 18.69 2 x [M6 x 13 DP] VIEW - 26. 1.236 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 1 8 6 2 lbs. 22 18 13 L 9 GRIP FORCE PER FINGER @ 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] 2 PSI [1.3 bar] 1.75 2.25 2.75 3.25 3.75.25.75 in. 57 7 81 95 18 121mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L C PSI [ bar] Y T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/ 2 Mz F/ 2 My X BSIC MODEL DCT - 25M - RE - V SIE SPRING VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT25-32 1 M8 PNP Inductive Sensor with Quick Disconnect* OISP-11 1 or 2 M8 NPN Inductive Sensor with Quick Disconnect* OISN-11 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES M5 djustable Flow Control VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-162 1 Viton Seal Repair Kit SLKT-162V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-DCT25-BR 1 *Sensor and cable sold separately. TM Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 6 lbs. 25 N 9 lbs. 1 N Maximum Compressive C 6 lbs. 25 N 9 lbs. 1 N Maximum Moment Mx 89 in.-lbs. 1 Nm 22 in.-lbs. 2.5 Nm Maximum Moment My 89 in.-lbs. 1 Nm 22 in.-lbs. 2.5 Nm Maximum Moment Mz 89 in.-lbs. 1 Nm 22 in.-lbs. 2.5 Nm Capacities are per set of jaws and are not simultaneous.55 [1].39 [1] M6 1.18 [3] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).3 [11].18 [.5] 3. [87.5].63 [16] 2.21 [56.2].39 [1] Sensors.79 [2] Ø.31 [8].63 [16].37 [9.5]
NGULR GRIPPER CT-32M-RE 18 SERIES Shielded plate 12.5 Jaws in gripping position at 1.551 5 1.77 17 =.67 = 3.9.15 -.6 1 -.17 -.2.5512 -.7 2 x M6 +.32 5 +.2 +.13.1969 +.8 67 2.6 9 9 DCT-RE SERIES 2.5 +.3 6 +.12 2 x.2362. x.7 [12] DP 2 x M8 x.67 [17] DP 29 ±.16 1.117 ±.6 3 ±.26 1.1811 ±.1 6.16 131 ±.125 5.1575 ±.9 116.57 33 1.3 7.5.3 72.5 2.85 9 3.7 3 ±.19 1.6929 ±.7 Side air port M5 x.2 [6] DP 12.7 Side air port M5 x.2 [6] DP 12.7 x [M3 x 7] 2 Slots to mount magnetic sensors 31.5 1.2 Specifications CT-32M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 1.75 in. [mm] @... 79 lbs. 353 N Stroke... 9 of stroke for each finger Weight... 1.83 lbs..83 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø... 1.26 in. 32 mm Displacement... 1.75 in 3. 28.6 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....35 /.26 sec. ccuracy... ±.3 in. ±.8 mm Repeatability... ±.2 in. ±.5 mm Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown..1 8.31 Gripper's top air port 1.2.5 O-Ring [Ø1.5 x Ø5 ] +.3 6 +.12 2 x.2362. x.7 [12] DP Top air por t M5 x.2 [6] DP (supplied plugged) 2 1.65 12.7 Top air por t M5 x.2 [6] DP (supplied plugged) 56 2.2 3 ±.19 1.6929 ±.7 21.5.85 19.75 2 x M8 x.67 [17] DP VIEW - 29 ±.16 1.117 ±.6 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 18 15 12 9 6 3 lbs. GRIP FORCE PER FINGER @ 3 27 WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS 2 13 7 1.75 2.25 2.75 3.25 3.75.25.75 5.25 5.75 in. 57 7 81 95 18 12 133 16mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] 2 PSI [1.3 bar] PSI [ bar] C Y T Mx F/ 2 Mz F/ 2 My X BSIC MODEL CT - 32M - RE - V SIE SPRING VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT25-32 1 M8 PNP Inductive Sensor with Quick Disconnect* OISP-11 1 or 2 M8 NPN Inductive Sensor with Quick Disconnect* OISN-11 1 or 2 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control M5 Elbow - 6mm OD Push-in (Metric) VLVF-8 1 or 2 Buna-NSeal Repair Kit SLKT-163 1 Viton Seal Repair Kit SLKT-163V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-CT32-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 65 lbs. 288 N 13 lbs. 57.6 N Maximum Compressive C 65 lbs. 288 N 13 lbs. 57.6 N Maximum Moment Mx 12 in.-lbs. 16 Nm 35 in.-lbs. Nm Maximum Moment My 12 in.-lbs. 16 Nm 35 in.-lbs. Nm Maximum Moment Mz 12 in.-lbs. 16 Nm 35 in.-lbs. Nm Capacities are per set of jaws and are not simultaneous.63 [16].7 [12] M8 1. [35] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).3 [11].16 [] 3.9 [1].63 [16] 2.68 [68.2].39 [1] Sensors.79 [2] Ø.31 [8].63 [16].7 [12]
NGULR GRIPPER CT-M-RE 18 SERIES Shielded plate 3 1.3 Jaws in gripping position at 16.63 9 1.93 3.9.15 17.67 [16g6] -.2.6299 -.7 2 x [M6] [ 5E7].1969 SF 7.5 2.933 9 9 [ 6H9] 2 x.2362 SF x.7 [12] DP 2 x [M8 x 17 DP] 165.5 6.516 39. 1.535 32. 1.2598 151.5 5.966 135 5.31 39.5 1.555 2.79 78 3.7 19.29 DCT-RE SERIES 2.51 53. 2.866 [G 1/8 x 8 DP] 18.71 12.7 [G 1/8 x 8 DP] x [M x 8 DP] 51 2.1 2 Slots to mount magnetic sensors Specifications CT-M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 2 in. [51mm] @... 133 lbs. 592 N Stroke... 9 of stroke for each finger Weight... 3.6 lbs. 1.39 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø... 1.575 in. mm Displacement... 3.173 in 3. 52 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....7 /.38 sec. ccuracy... ±.36 in. ±.9 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown..1 8.31 Gripper's top air port 1.2.5 O-Ring [Ø1.5 x Ø5 ] [ 6H9] 2 x.2362 SF x.7 [12] DP [M5 x 6 DP] (supplied plugged) 52 2.5 18.71 [M5 x 6 DP] (supplied plugged) 66 2.6 53. 2.866 25.5 1. 18.71 2 x [M8 x 17 DP] VIEW - 39. 1.535 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information How to Order: (Order ccessories separately from Basic Model) FINGER FORCE - F/2 N 3 25 2 15 1 5 lbs. GRIP FORCE PER FINGER @ 67 56 WRNING! DO NOT EXCEED 5 MXIMUM EFFECTIVE FINGER LENGTHS 3 22 11 2 3 5 6 7 in. 51 76 12 127 152 178mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] PSI [2.7 bar] 2 PSI [1.3 bar] PSI [ bar] C Y T Mx F/ 2 Mz F/ 2 My X BSIC MODEL CT - M - RE - V VITON SELS SIE SPRING SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT-63 1 M12 PNP Inductive Sensor with M12 Quick Disconnect* OISP-17 1 or 2 M12 NPN Inductive Sensor with M12 Quick Disconnect* OISN-17 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 M12 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M12 Quick Disconnect 5 Meter Cable Length * CBL-18 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control G1/8 Elbow - 6mm OD Push-in (Metric) VLVF-5 1 or 2 Buna-NSeal Repair Kit SLKT-16 1 Viton Seal Repair Kit SLKT-16V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-CT-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 9 lbs. 2 N 19 lbs. 8 N Maximum Compressive C 9 lbs. 2 N 19 lbs. 8 N Maximum Moment Mx 195 in.-lbs. 22 Nm 9 in.-lbs. 5.5 Nm Maximum Moment My 195 in.-lbs. 22 Nm 9 in.-lbs. 5.5 Nm Maximum Moment Mz 195 in.-lbs. 22 Nm 9 in.-lbs. 5.5 Nm Capacities are per set of jaws and are not simultaneous.63 [16].7 [12] M8 1.57 [] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).69 [17.5].22 [5.5].59 [116.5] 1.18 [3] 2.87 [73].39 [1] Sensors.87 [22] Ø.7 [12].83 [21].57 [1.5]
NGULR GRIPPER CT-5M-RE 18 SERIES Shielded plate 1.57 Jaws in gripping position at 18.71 6 2.36 5.2 21.83 [18g6] -.2.787 -.7 2 x [M8] [ 6E7].2362 SF 9 3.5 9 9 DCT-RE SERIES 2.52 [ 8H9] 2 x.315 SF x.63 [16] DP 2 x [M1 x 22 DP] 6. 1.811. 1.578 21 7.91 183. 7.27 163 6.2 1.73 2.79 12.5.35 133 5.2 6. 2.3622 [G 1/8 x 8 DP] 25.98 15.59 [G 1/8 x 8 DP] x [M x 8 DP] 6 2.36 2 Slots to mount magnetic sensors Specifications CT-5M-RE Total Rated Grip Force, F @ 1 psi [7 bar] L = 2.5 in. [6mm] @... 21 lbs. 893 N Stroke... 9 of stroke for each finger Weight....87 lbs. 2.21 Kg Pressure Range... 6-1 psi -7 Bar Cylinder Bore Ø... 1.968 in. 5 mm Displacement... 5.61 in 3. 92 cm 3 Temperature Range Standard Seals... -3 ~18 F -35 ~8 C Viton Seals... -2 ~3 F -3 ~15 C ctuation (open/close)....5 /.2 sec. ccuracy... ±.36 in. ±.9 mm Repeatability... ±.2 in. ±.5 mm. Valve required to actuate single acting... 3-way, 2-position Valve required to actuate double acting... -way, 2-position Our grippers are supplied with open side air ports and top air ports plugged. When operating top air ports, produce manifold sealing as shown..1 8.31 Gripper's top air port 1.2.5 O-Ring [Ø1.5 x Ø5 ] [ 8H9] 2 x.315 SF x.63 [16] DP [M5 x 6 DP] (supplied plugged) 62 2. 25.98 [M5 x 6 DP] (supplied plugged) 76 2.99 6. 2.3622 3 1.18 3 1.18 2 x [M1 x 21 DP] VIEW - 6. 1.811 UNLESS OTHERWISE NOTED LL TOLERNCES RE S SHOWN BELOW Imperial in. Metric [mm] Dimensions are Third ngle ll Dowel Holes are SF (Slip Fit). Metric Threads. = ±.1 [.] = [±.25] symmetrical about Projection Locational Tolerance Course Pitch. = ±.5 [.] = [±.13] centerline ±.5" or [±.13mm]. = ±.5 [.] = [±.13] NOTE: Jaws have to be designed for a gripping position (parallel jaws). Jaws will close 1.5 past parallel. To limit shocks at the end of an opening or closing stroke, it is highly recommended to design jaws with minimal inertia (as light and short as possible). Flow Controls make it possible to reduce the rotation speed and are highly recommended. Loading Information FINGER FORCE - F/2 N 5 35 3 25 2 15 1 5 lbs. 11 9 79 67 56 5 3 22 11 2.5 3.5.5 5.5 6.5 7.5 8.5 9.5 in. 6 89 12 1 165 191 216 21mm EFFECTIVE FINGER LENGTH FROM ROTTION XIS - L L 1 PSI [7 bar] 8 PSI [5.5 bar] 6 PSI [.1 bar] GRIP FORCE PER FINGER @ PSI [2.7 bar] 2 PSI [1.3 bar] PSI [ bar] C Y T Mx WRNING! DO NOT EXCEED MXIMUM EFFECTIVE FINGER LENGTHS F/ 2 Mz F/ 2 My X How to Order: (Order ccessories separately from Basic Model) BSIC MODEL CT - 5M - RE - V SIE SPRING VITON SELS SENSOR CCESSORIES* ORDER # QTY/UNIT PNP Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSP-17 1 or 2 NPN Magneto Resistive Sensor Short Barrel M8 w/qk Disc* OHSN-17 1 or 2 Inductive Sensor Mounting Kit (mounts 2 sensors) SDCT-63 1 M12 PNP Inductive Sensor with Quick Disconnect* OISP-17 1 or 2 M12 NPN Inductive Sensor with Quick Disconnect* OISN-17 1 or 2 M8 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M8 Quick Disconnect 5 Meter Cable Length * CBL-13 1 or 2 M12 Quick Disconnect 2 Meter Cable Length * CBL-1 1 or 2 M12 Quick Disconnect 5 Meter Cable Length * CBL-18 1 or 2 PNEUMTIC CCESSORIES dj. Flow Control G1/8 Elbow - 6mm OD Push-in (Metric) VLVF-5 1 or 2 Buna-NSeal Repair Kit SLKT-165 1 Viton Seal Repair Kit SLKT-165V 1 MOUNTING CCESSORIES djustment Stop Kit (1 Shielded Plate + 1 Stop) KP-CT5-BR 1 *Sensor and cable sold separately. Loading Capacity Static Dynamic Imperial Metric Imperial Metric Maximum Tensile T 11 lbs. 9 N 22 lbs. 98 N Maximum Compressive C 11 lbs. 9 N 22 lbs. 98 N Maximum Moment Mx 266 in.-lbs. 3 Nm 66 in.-lbs. 7.5 Nm Maximum Moment My 266 in.-lbs. 3 Nm 66 in.-lbs. 7.5 Nm Maximum Moment Mz 266 in.-lbs. 3 Nm 66 in.-lbs. 7.5 Nm Capacities are per set of jaws and are not simultaneous.79 [2].63 [16] M1 1.77 [5] MX. DJUSTBLE STOP KIT (BR) INDUCTIVE SENSORS ND MOUNTING KIT (SD).69 [17.5].2 [5] 5.55 [11] 1.18 [3] 3.8 [97.5].39 [1] Sensors.87 [22] Ø.7 [12].83 [21].75 [19]
DCT-RE/CT-RE SERIES EXPLODED VIEW 2 8 1 1 6 3 7 6 x2 x2 9 x2 x2 x2 Item Qty Name 1 1 Body 2 1 Driver 3 1 Piston 2 Jaw 5 1 Washer 6 1 Cap 7 1 Shielded Plate 8 2 Wiper Cover 9 2 Drive Pin 1 2 Pivot Pin 5 1 Magnet 6 1 Spring NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. ssembly Procedure 1) Lubricate and install the seals into cap (x1), piston (x2) and body (x1) 2) If top air ports are used, clear them and plug the side air ports on the body (#1) 3) Lubricate the sloping rack of jaws (#) ) Install both drive pins (#9) into driver (#2) through sloping racks of jaws. Check that the pin flat surface is correctly aligned before continuing with their installation. 5) Lock drive pins in the driver with screws, tightening down on to the flat surface of the pins. 6) Position driver and jaws assembly into body. 7) Install both pivot pins (#1) into body, through the bore of jaws. Check that the pin flat surface is correctly aligned before continuing with their installation. 8) Pivot pin locking: - DCT-12 (not shown): lock pivot pins into body with screws, tightening down on to the flat surface of the pins (pins are fixed into body and rotating into jaws) - DCT-16 to CT-5: lock pivot pins into jaws with screws, tightening down on to the flat surface of the pins (pins are fixed into jaws and rotating into body) 9) Magnet mounting: - DCT-12 to DCT-2: install the magnet (#5) on the washer (#5) - DCT-25 to CT-5 (not shown): install magnet (#5) onto piston (#3) and lock it by means of its retaining ring. 1) Piston mounting: - DCT-12 to DCT-2: insert the spring, then the piston and the washer with magnet into body. Fix the assembly at the end of the driver with screw. - DCT-25 to CT-5 (not shown): insert the spring, then the piston with magnet into body. Fix the assembly at the end of the drivers with screw. 11) Check unit operation unladen. 12) Install the cap (#6) into body and lock it by means of its retaining ring. 13) Place both wiper covers (#8) into body and lock them with their screws. 1) Fix the shielded plate (#7) onto body with both screws. DCT-RE/CT-RE SERIES MINTENNCE 2.53 SK Seal Repair Kit Order # s Product Data Sheets SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
DCT-RE/CT-RE SERIES SSEMBLED VIEW DCT-RE/CT -RE SERIES MINTENNCE 2.5 6 1 5 6 5 3 9 Item Qty Name 1 1 Body 2 1 Driver 3 1 Piston 2 Jaw 5 1 Washer 6 1 Cap 7 1 Shielded Plate 8 2 Wiper Cover 9 2 Drive Pin 1 2 Pivot Pin 5 1 Magnet 6 1 Spring 8 1 NOTE: Contact the Robohand Sales Department for a complete spare parts list with order numbers and prices. 2 7 CCESSORY INSTLLTION & DJUSTMENT INSTRUCTIONS 3 DCT16M, 2M-RE DCT-25M, 32M-RE CT-M, 5M-RE 1 1 1 2 2 2 5 2 7 6 1 6 6 7 3 5 3 8 5 8 8 3 Installation - djustment Stop 1) Unscrew both screws for mounting of the shielded plate and remove it. 2) Fix the new shielded plate (#1) and the stop (#2) onto body with both screws (#3) 3) Install the locknut system (#) and (#5) on the stop. ) Tighten screw for maximum target jaw opening and lock with locknut. Installation - Inductive Sensor Holders 1) Fix the flags (#1) at the end of pivot pins with their screws (#2) 2) Holder mounting: - DCT-16M to DCT-32M: fix holder (#3) and spacer (#5) onto body with both screws (#6) - CT-M to CT-5M: fix holder (#3) onto body with both screws (#6) 3) Sensor mounting: - DCT-16M to DCT-2M: unscrew lightly both screws for mounting (#6) of holder and insert sensor (#8, not included) into it. Position sensor so that it senses up on flag. Lock the sensor by tightening both screws. - DCT-25M to DCT-32M: unscrew lightly screw (#7) on holder and insert sensor (#8, not included) into it. Position sensor so that it senses up the flag. Lock the sensor by tightening screw. - CT-M to CT-5M: insert sensor (#8, not included) in stop into holder. Lock the sensor by tightening the collar holder with both screws (not shown). ) djust flag position by unscrewing their screws for desired sensing positions. SK KRYTOX Seal Kit Items Thread Locker Krytox Lubricant Lightweight Machine Oil Teflon Based Grease Super Bonder Third ngle Projection
QULITY PRECISION DESIGNDURBILITY NOTES PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY 2.55 PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DURBILITY QULITY PRECISION QULITY PRECISION DURBILITY PRECISION DURBILITY QULITY DCT-RE/CT -RE SERIES MINTENNCE
FU SERIES ngular Grippers- Food Handling Gripper Series 2.56 FETURES & BENEFITS: Designed for direct product contact in the food zone, according to the food industry standard (EN 1672-2) ll parts are corrosion resistant, non-toxic, non-contaminating, non-porous, non-absorbent and non-reactive Stainless steel design resists chemical cleaning procedures Optional body made of High Performance Polymer, conform to FD, for a significantly lighter weight Electro-polished exterior with no recessed or inaccessible zones prevents retention of contaminants and simplifies cleaning Sealed motion components (IP69K design) for high-pressure and high-temperature daily cleanings ny metal/metal contact protected by gasket to obtain a leakproof assembly against bacteria ngular gripper design for easier radial sealing of jaws Optional security springs for external gripping, in case of air supply failure, in single acting or spring assist mode No external fasteners to avoid any foreign matter in food Contains special lubricants suitable for food industry Long maintenance-free service life PPLICTIONS: Food zone and splash zone handling of product Non-food zone applications Other applications requiring a sealed and corrosion resistant gripper Shown with Optional Finger ttachment Kit