omfort365 Dsplays the Thermostat Mode HOLD, SHEDULE or VAANT Dsplays the upstars arflow Dsplays the downstars arflow Dsplays the Arflow Mode MATI or MANUAL Dsplays the tme, day and schedule MORNIN, DAYTIME, EVENIN or NIHT Key Dsplays the User optons. Key Selects Thermostat Mode HOLD, SHEDULE or VAANT Descrpton The 365 thermostat controls heatng, coolng and arflow to the upstars and downstars usng an upstars and a downstars modulatng damper. A temperature sensor located upstars montors the upstars temperature and the temperature sensor n the 365 montors the downstars temperature. The 365 adjusts the upstars and downstars arflow durng heatng and coolng calls to mantan unform upstars and downstars temperatures. S Off,,, S or ontnuous THERMOSTAT S Hold, or Vacant mode. PRORS PER DAY Mornng, tme, Evenng and Nght. PROR FORMAT Weekdays and weekend 5/2. TEMPERATURE OVERRIDE Temperature s held for 4 hours when adjusted n mode. After nstallng and wrng dampers and sensors to the thermostat, HEK FOR ERROR MESSAES (p.4) Set tme of day (p.4) Set s (p.5-7). s 1 through 5 determne the equpment operaton and must be set f dfferent than Factory Settngs. Warranty Ths thermostat s warranted to be free of defects due to workmanshp or materals under normal use and servce for a perod of 5 years from date of nstallaton and not longer than 6 years from manufacturng date code. omfort365 Installer Manual Model 365T21 and 365T21WF ATTENTION INSTALLER HEAT Ver1.7 / Ver1.9 Jul 2017 Dsplays the heatng or coolng temperature UP/DOWN Keys. Dsplays the downstars () or upstars (2) temperature. Key OFF, HEAT, OOL or Key or ON Key Used to save optons and return to thermostat operaton Key Used to advance through optons AIRFLOW ONTROL Arflow can be turned off usng 15. Dampers fully open, nghttme arflow optons are dsabled and arflow s no longer dsplayed on the thermostat. AIRFLOW LIMITS Maxmum upstars and downstars, heatng and coolng arflow lmts can be set durng nstallaton. NIHTTIME OPERATION The 365 thermostat uses the upstars temperature sensor to control heatng and coolng calls and drects more arflow upstars. If bedrooms are located downstars, the Nghttme Arflow opton should be turned off. PATIBLE EQUIPMENT as/electrc equpment wth 2- stage heatng and 1 stage coolng or 1 stage heatng and 2- stage coolng and heat pumps wth 2-stage heatng and 2- stage coolng. UPSTAIRS TEMPERATURE SENSOR One TS510W sensor or two TS520W upstars temperature sensors can be used. MODULATIN DPERS Round or rectangular dampers usng the A80MT actuator and up to 1 nch statc pressure. POWER Operates on 24VA from the HVA equpment usng the R and wres. To dsable arflow control so the thermostat operates as a typcal thermostat, use 17 to turn arflow control off. The thermostat wll control the system as any other thermostat and the nghttme arflow opton wll be dsabled. Nghttme Arflow. If bedrooms are located downstars, the Nghttme Arflow should be turned OFF usng the User s. eontrols eontrols, Inc. 26072 Mert rcle #110 / Laguna Hlls, A 92653 949-916-0945 Fax 949-458-8502 www.eontrolsusa.com
SEPARATE THE 365 SUBBASE Place a slotted screwdrver n the slots as shown and rotate to remove subbase from the 365 housng. INSTALL UPSTAIRS & DOWNSTAIRS DPERS Install an R80T damper n the duct supplyng ar to the upstars and wre the termnals to the correspondng termnals on the 365T. Install a second R80T damper n the duct supplyng ar to the downstars and wre t to the 365T. Each damper uses 2.4VA of power. Ensure that damper nstallaton does not cause obstructon to the damper blade. When two or more dampers are requred to defne the upstars or downstars zones, the damper may be wred n parallel. LEDS on the damper actuator ndcate when the damper s fully open (green) or fully closed (red). reen LED Red LED ATTAH THE SUBBASE TO THE WALL Attach the subbase to an nteror wall and about 5-feet above the floor as shown usng the screws and wall anchors suppled. The wres to the dampers, HVA equpment and the upstars temperature sensor pass through the openng between the termnals. EQUIPMENT R WOB Y W2E/Y2 365T21 INSTALL TWO AA BATTERIES The batteres power the clock when 24VA power s lost. Slde the battery cover downward and nstall the two AA batteres as shown. WIRIN INSTRUTIONS Warnng rn the power to the HVA equpment off before wrng. Equpment Wrng, as/electrc, 2H/1 Use 5-conductor, 18 or 20 gage, thermostat cable. 365 Wre olor Equpment Functon R Red R, Rc, Rh 24VA Power Blue ommon W/OB Whte W, W1 Stg1 ng Y1 Yellow Y, Y1 ng reen Fan W2E/Y2 Brown W2 Stg2 ng Equpment Wrng, as/electrc, 1H/2 Use 5-conductor, 18 or 20 gage, thermostat cable. 365 Wre olor Equpment Functon R Red R, Rc, Rh 24VA Power Blue ommon W/OB Whte W, W1 Stg1 ng Y1 Yellow Y, Y1 Stg1 ng reen Fan 2 W2E/Y2 Brown Y2 Stg2 ng
WIRIN DIAR WIRIN INSTRUTIONS (ont) E HP HVA System Y2 Y2 W2 E Y Y W O or B R R Model 365T21 Thermostat EQUIPMENT R W/OB Y1 W2E/Y2 365T21 Model R80T-XX Damper Model A80-MO Damper Actuator Modulatng or Open/lose 24VA,2.4VA Made n USA eontrols, Inc. Model R80T-XX Damper Model TS5 Temperature Model A80-MO Damper Actuator Modulatng or Open/lose 24VA,2.4VA Made n USA eontrols, Inc. 3 Equpment Wrng, Pump, 1 ompressor Use 5-conductor, 18 or 20 gage, thermostat cable. 365 R WOB Y1 W2E/Y2 Equpment Wrng, Pump, 2-ompressor Use 5-conductor, 18 or 20 gage, thermostat cable. 365 R WOB Y1 W2E/Y2 Wre olor Red Blue Whte Yellow reen Brown Wre olor Red Blue Whte Yellow reen Brown Damper Wrng Equpment R, Rc, Rh O or B Y, Y1 W, W2 or E Equpment R, Rc, Rh O or B Y, Y1 Y2 Functon 24VA Power ommon Rev Valve ompressor Fan Aux Functon 24VA Power ommon Rev Valve Stg1 ompressor Fan Stg2 ompressor Use 3-conductor, 18 or 20 gage, thermostat cable to wre from the 365 Thermostat to the upstars and downstars dampers. There are separate termnals for the upstars and the downstars dampers. 365 Wre olor Whte Red reen Damper Functon ommon loses damper Opens damper Multple dampers can be used to construct the upstars or downstars zones. Dasy chan termnals to, to and to. Temperature Wrng Use 2-conductor, 18 or 20 gage, thermostat cable to wre from the 365 Thermostat to the upstars temperature sensor. 365 SNR SNR Wre olor Whte Red SNR SNR Functon Thermstor Thermstor For sngle temperature sensor applcaton, use Model TS5-10. Two temperature sensors can be nstalled n dfferent areas upstars and the two temperatures wll be averaged. For dual sensor applcatons, use Model TS5-20 and dasy chan the sensors.
Temperature Wrng (ont) HAND TIHTEN Prnted crcut board Brass washer Place wre between brass washer and the prnted crcut board and hand tghten screw. The TS5 can be nstalled n a sngle gang box or drectly to the wall usng the hardware provded. heck for the followng error messages: No Power Message np s dsplayed when there s no power to the system. If the message s dsplayed when the system s powered, check the wrng from the thermostat to the system for errors. Error Message ns s dsplayed when there s an error wth the upstars sensor(s). heck for open wres or shortages. When the ns message s dsplayed, the thermostat wll contnue to control the system and automatcally opens both dampers and dsables arflow control untl the sensor error s corrected. OOL OOL Sngle Temperature Model TS5-10 Temperature Dual Temperature s Model TS5-20 Temperature Model TS5-20 Temperature Press the touchscreen wth your fngertp only, usng a frm touch. Do not use a sharp object such as a pen or pencl. Set Tme and Touch here to change the tme and day of the week. OOL HANE THE HOUR change the HOUR. Touch to save the hour and go to change the mnute. Wre to the 365T11 Wre to the 365T11 HANE THE MINUTE change the MINUTE. Touch to save the mnute and go to change the day of the week. We HANE THE DAY OF THE WEEK change the DAY OF THE WEEK. Touch to save the day fo the week and return to thermostat operaton. 4
INSTALLER OPTIONS 01 02 03 Descrpton Equpment Type Reversng Valve (Only dsplayed f HP selected) ompressor Stages Dsplay rev pr Range E or HP o or b 0 or 1 (E), 0 to 2 (HP) Default as/electrc O 1 (E), 2 (HP) 04 ng Stages Htg 0, 1 or 2 1 05 Fan Operaton. (Only dsplayed f E selected) Fan A(Up) or EL(Down) A 06 07 08 09 ompressor Mnmum Off Tme (mnutes). as Mnmum Off Tme (mnutes). Mnmum Run Tme (mnutes). On-Off Temperature Dfferental ot HOt r n t O O o 0 to 9 0 to 9 0 to 9 0, 1 or 2 2 0 2 1 10 11 12 0 ng On 1 o above setpont, Off at setpont. ng On1 o below setpont, Off at setpont. 1 ng On 1 o above setpont, Off.5 o below setpont. ng On1 o below setpont, Off.5 o above setpont. o o o o 2 ng On 1 above setpont, Off 1 below setpont. ng On1 below setpont, Off 1 above setpont. Smart Recovery. Vacant ng Setpont. Vacant ng Setpont. S r V A + V A + 0n(Up) or Off(Down) 44 to 75 74 to 95 Off 65 80 13 albrate A L +/- 5 0 14 albrate. A L +/- 5 0 15 Arflow Update Tme A F t 1 to 20 mnutes 2 16 Nght Level LD Backlght BL + Nght On(Up) or Off(Down) 17 Arflow ontrol On or Off AF On(Up) or Off(Down) 18 Enable Selectng Manual Arflow ontrol. UF On(Up) or Off(Down) 19 Up Stage Tme USt 5 to 180 mnutes 20 21 22 23 24 25 Maxmum Arflow n ng. Maxmum Arflow n ng. Maxmum Arflow n ng. Maxmum Arflow n ng. Maxmum Temperature Dfference Between and. AESSIN INSTALLER OPTIONS To access the Installer s, TOUH and HOLD the hdden Enter key for 7 seconds untl the frst appears on the screen. HAF+ AF+ HAF+ AF+ df 100 to 155% 100 to 155% 100 to 155% 100 to 145% 0 to 10 Factory Restore Fr No(Next) or Yes(Enter) + UP NA 01 Selectng the Equpment Type Factory Default: E. Range: E or HP Ths opton s used to select gas/electrc or heat pump equpment. select gas/electrc (E) or heat pump (HP). On On Off 30 150% 140% 150% 140% 2 The hdden BAK key can be used to return to prevous optons. OOL TOUH and HOLD ths key for 7 seconds to access the Installer s. Touch or. 02 Reversng Valve Factory Default: O. Range: o or b select o for O-Type or b for B- Type. Touch or. Ths opton s used to select an O or B type reversng valve. (Only dsplayed f HP selected) Press the touchscreen wth your fngertp only, usng a frm touch. Do not use a sharp object such as a pen or pencl. The key s used to dsplay the next opton. The key s used to save optons and return to normal thermostat operaton. The hdden BAK key s used to return to prevous optons and s located to the left of the key. 03 Settng the ompressor Stages Factory Default: 1. Range: 0 or 1 Ths opton s used to set the number of compressor stages. set 0 or 1 stage. Touch or. 5
04 Settng the ng Stages Factory Default: 1 Stage. Range: 0,1 or 2 Ths opton s used to set the number of heatng stages. set 0, 1 or 2 stage. Touch or. 10 Smart Recovery Factory Default: Off. Range: On or Off. Smart recovery ntates a heatng or coolng call so that the space s at temperature when the setback perod ends. Touch the UP key to select ON to turn on smart recovery or touch the DOWN key to select OF to turn smart recovery off. Touch or. 05 Settng the Fan Operaton Factory Default: as. Range: A or EL Touch the UP key to select EL for electrc operaton where the thermostat actvates the ndoor fan ( termnal) durng heatng calls or DOWN key to select A for gas operaton where the equpment plenum sensor actvates the ndoor fan n heatng calls. (Only dsplayed f E selected) 11 Vacant ng Setpont Factory Default: 65oF. Range: 44oF to 75oF select the heatng temperature when the space s vacant. Touch or. Vacant Touch or. 06 ompressor Mnmum Off Tme Factory Default: 2 Mnutes. Range: 0 to 9 Mnutes change the mnmum off tme (mnutes) before restartng the compressor. Touch or. 12 Vacant ng Setpont Factory Default: 80oF. Range: 74oF to 95oF select the coolng temperature when the space s vacant. Touch or. Vacant 07 ng Mnmum Off Tme Factory Default: 0 Mnutes. Range: 0 to 9 Mnutes change the mnmum off tme (mnutes) before restartng a gas furnace or electrc strp heater. Touch or. change the mnmum run tme (mnutes) before turnng a system off. Touch or. 08 Mnmum Run Tme Factory Default: 2 Mnutes. Range: 0 to 9 Mnutes 13 albrate Temperature Factory Default: None. Range - +/-5o change the downstars () temperature to the temperature that the user feels s correct. Touch or. Touch or 14 albrate Temperature Factory Default: None. Range - +/-5o change the upstars (2) temperature to the temperature that the user feels s correct. 2 09 Settng On-Off Temp Dfferental Factory Default: #1. Range: 0, 1 or 2. select 0, 1, 2. Touch or. Dfferental Mode0 Dfferental Mode1 Dfferental Mode2 o 0.5 On/Off Span. o 1.0 On/Off Span. o 1.5 On/Off Span. 6 15 Arflow Update Tme Factory Default: 2 Mnutes. Range: 1 to 20 Mnutes. Ths s the frequency, n mnutes, that the damper poston s updated. set the tme n mnutes to update the upstars and downstars arflow. Touch or.
16 Nght Level LD Backlght Factory Default: On. Range: On or Off. The LD has a low level backlght that can be used as a nght lght. Touch the UP key to turn the low level backlght ON or touch the DOWN key to turn OFF. 21 Maxmum Arflow n ng Factory Default: 140%. Range: 100% to 160%. select the maxmum allowable upstars arflow n coolng. Touch or. Touch or. Nght 17 Arflow ontrol, On or Off Factory Default: On. Range: On or Off. Ths opton turns the automatc arflow control on or off. If on, the thermostat wll automatcally adjust the arflow. If off, arflow s dsabled. Touch the UP key to select ON for arflow control or touch the DOWN key to select OFF to dsable arflow control. Touch or. 19 Upstagng Tme set the tme at whch second stage heatng or coolng s actvated. Touch or. Factory Default: 30 mnutes. Range: 5 to 180 mnutes 18 Enable Selectng Manual Arflow ontrol Factory Default: Off. Range: On or Off. Ths opton enables the user to select automatc or manual arflow. In automatc, the thermostat controls the arflow. matc s the default. In manual, the user must adjust the arflow. Touch the UP key to select ON to enable manual arflow control or touch the DOWN key to select Off so that manual arflow control s not an opton. Touch or. 22 Maxmum Arflow n ng Factory Default: 150%. Range: 100% to 160%. select the maxmum allowable downstars arflow n heatng. Touch or. select the maxmum allowable downstars arflow n coolng. Touch or. select the maxmum allowable temperature dfference between the upstars and downstars. Touch or. 23 Maxmum Arflow n ng Factory Default: 140%. Range: 100% to 160%. 24 Maxmum Temperature Dfferental Factory Default: 2oF. Range: 0 o to 10o F maxmum allowable temperature dfference between the upstars and downstars temperatures. When the temperature dfference s equal to or greater than the allowed dfferental, the arflow s adjusted. 25 Factory Restore WARNIN Factory Restore resets ALL settngs. Touch or to return to normal thermostat operaton. Touch the hdden BAK key to return to prevous opton. For optons 20-23, use the nstaller test on pages 7-8 to determne the maxmum allowable arflow. 20 Maxmum Arflow n ng Factory Default: 150%. Range: 100% to 160%. select the maxmum allowable upstars arflow n heatng. Touch or. 7 To restore factory settngs, touch, then touch the UP key. Demand Sde Management WF model only. When partcpatng n Demand Sde Management wth the utlty company, the thermostat wll dsplay U (Utlty ontrol) when the utlty company has lmted the coolng setpont settng n the thermostat. OOL
AESSIN THE TEST The Menu s used to test the Indoor Fan Operaton, Allowable ng Arflow Lmts and Allowable ng Arflow Lmts. The Menu can also be used to perform the HERS Total Arflow test. 05-06 actvates a coolng call and opens both dampers to 100% enablng the nstaller to perform the test. To access the Menu, TOUH and HOLD the hdden Next key for 7 seconds untl the fan test screen ( 01) appears. OOL TOUH and HOLD ths key for 7 seconds to access the Installer s. 01-02 ng Indoor Fan Operaton Ths test s used to verfy that the ndoor fan s operatng correctly. In 1, the Fan s Off. Touch to go to 2 to turn on the ndoor fan. Verfy the fan s operatng and delverng arflow to the upstars and downstars.. Touch to go ng ng Arflow Lmts. 03-04 ng ng Arflow Lmts (cont.) To determne the maxmum allowable downstars arflow, touch the DOWN key untl the arflow s too great and causes nose or annoyance. Increase the arflow usng the UP key untl t s acceptable. Ths s the maxmum allowable downstars arflow n heatng. Record the arflow value. Maxmum Allowable Arflow n ng Touch to go to ng ng Arflow Lmts. 05-06 ng ng Arflow Lmts Ths test s used to determne the maxmum allowable upstars arflow and maxmum allowable downstars arflow n OOLIN. The test can also be used to perform the HERS Total Arflow test. The test actvates a coolng call and opens both dampers to 100%. In 5, the system s Off. Touch to go to 6 to actvate coolng. Verfy the equpment s operatng. To determne the maxmum allowable upstars arflow, touch the UP key untl the arflow s too great and causes nose or annoyance. Lower the arflow usng the DOWN key untl t s acceptable. Ths s the maxmum allowable upstars arflow n coolng. Record the arflow value. 03-04 ng ng Arflow Lmts In 3, the system s Off. Touch to go to 4 to actvate heatng. Verfy the equpment s operatng. To determne the maxmum allowable upstars arflow, touch the UP key untl the arflow s too great and causes nose or annoyance. Lower the arflow usng the DOWN key untl t s acceptable. Ths s the maxmum allowable upstars arflow n heatng. Record the arflow value. Ths test s used to determne the maxmum allowable upstars arflow and the maxmum allowable downstars arflow n HEATIN. Maxmum Allowable Arflow n ng To determne the maxmum allowable downstars arflow, touch the DOWN key untl the arflow s too great and causes nose or annoyance. Increase the arflow usng the UP key untl t s acceptable. Ths s the maxmum allowable downstars arflow n coolng. Record the arflow value. Maxmum Allowable Arflow n coolng Touch to end testng and return to normal thermostat operaton. Enter the maxmum arflow lmts usng s 20 through 23 of the nstaller menu. Maxmum Allowable Arflow n ng 8