OWNER S INSTRUCTION MANUAL

Transcription

1 WR S ISTRUTI UL Sportsman Seres ower-ole Shallow Water nchor Installaton peraton antenance UTI: Read ths nstructon manual carefully. ecome famlar wth the controls and know how to operate the ower-ole shallow water anchor system safely. US at o. 6,041,730

2 RTULTIS on your purchase of a ower-ole Sportsman shallow water anchor system. It has been desgned, engneered, and manufactured to provde the best possble performance and dependablty for years of enjoyment. lease read and retan ths manual. The nformaton contaned n ths manual descrbes the proper procedures for safely nstallng, operatng and mantanng your ower-ole shallow water anchor. UTI: Do not use the ower-ole shallow water anchor as your prmary anchorage. ever leave your boat unattended whle anchored solely wth the ower-ole shallow water anchor.

3 TRII Read ths operator s manual carefully. ecome famlar wth the controls and know how to operate your ower-ole shallow water anchor properly. Do not allow chldren to operate the ower-ole shallow water anchor wthout adult supervson. Do not modfy the unt n any way or add accessores not ntended for ths unt. lways dsconnect power from ower-ole shallow water anchor before servcng. RTI In the event of pump falure the ower-ole shallow water anchor may be manually rased by applyng enough pressure to bypass the ole-rotector valve thus allowng the unt to come all the way up to the stowed poston. If the ower-ole shallow water anchor s beyond reach t can be forced up by drvng the boat forward to shallower water. Depressng the up button on the ower- ole shallow water anchor control may offer assstance. D T TU T SI. e sure to have the ower-ole shallow water anchor n the full up poston when usng outboard motor at hgh speeds. eep your hands and clothng completely clear of the ower-ole shallow water anchor at all tmes. Do not use the ower-ole shallow water anchor as a step or handle to enter or ext the boat. ever allow chldren to play wth or around the ower-ole shallow water anchor. ever leave your boat unattended wth the ower-ole shallow water anchor as the prmary anchorage. In hgh wnd or rough seas the ower-ole shallow water anchor may releve holdng pressure to protect your boats transom. If any debrs gets caught around the ower-ole shallow water anchor, DIST power from motor and remove any debrs. IT D STR UTI ydraulc lnes always have pressure, dsconnectng the lnes wll cause sudden hgh pressure leakage and ower-ole shallow water anchor falure whch may cause bodly harm. Inspect all hydraulc lne fttngs between usage for proper tghtness to be sure there are no leaks. ake sure all power connectons are secure and free of corroson once every three months. Inspect all nuts, bolts and screws after 100 cycles of usage for proper tghtness to be sure the ower-ole shallow water anchor s n safe workng condton. ote: ½ Lock nuts at top knuckle jont and ½ lock nuts at hydraulc cylnder should be tghtened to 48 nch pounds / 4 foot pounds of torque. The ½ lock nuts on stern bracket should be tghtened to 72 nch pounds / 6 foot pounds of torque. nce tghtened f ower-ole shallow water anchor s stll lose replace bushngs. Inspect all hydraulc lnes between usage for possble chaffng or damage from knkng or abrason. eep the hydraulc reservor flled wthn the ndcator marks at all tmes. Thoroughly rnse all movng parts after each use. lways make sure the ower-ole shallow water anchor s n the full up poston when the boat s on the traler. Lubrcate the hnge bushngs perodcally wth a spray Lthum rease to prevent the unt from squeakng.

4 Installaton Tools & ardware Step 1: hoose a ountng Locaton Transom mount opton 1/2 & 9/16 Wrenches, Sockets and Ratchet lectrc or attery perated Drll our oot Straght dge arne rade Sealant Tape easure Wre utters Wre rmpers Razor Tubng utters Small unnel 9/64 & 5/16 Drll ts #2 hllps ead t or Screwdrver g Saw or Rotary Saw ty(2) 5/16 x 3.5 cylnder ram bolt ty(2) 5/16 low-profle brass lock nuts ty(4) 5/16 x 3.5 all-thread transom mount bolts D ty(2) thru-hull bushngs ty(4) 5/16 tall brass lock nuts ty(4) small D washers ty(4) cylnder ram bolt bushngs ty(4) 5/16 neo-bond washers ty(4) 5/16 fender washers ty(2) large cylnder ram spacers ty(2) small cylnder ram spacers L ty(3) marne wre tes ty(4) #10 wood screws ty(2) #6 wood screws ty(2) 3/8 mountng bolt ty(2) 3/8 neo-bond washers ty(1) mountng gasket R ty(2) rng connectors S ty(3) wre plug connectors T ty (1) 5ft black mesh tubng cover 2. The lowest pont of the ower-ole shallow water anchor wll need to be at least 4 above ths straght edge. If the ower-ole shallow water anchor s mounted lower than the 4 mnmum the vessel may experence adverse handlng effects. learance 1. If the vessel s equpped wth trm tabs make sure the ower-ole shallow water anchor wll not nterfere wth the actuators or the tabs themselves. 2. If the vessel s equpped wth 9 or less trm tabs the standard 4 mnmum mountng heght wll clear the tab. If the tabs are larger than 9 the ower-ole shallow water anchor wll need to be mounted hgher to prevent nterference. 3. Turn and tlt the outboard motor all the way n the drecton of the ower-ole shallow water anchor. ove the ower-ole shallow water anchor and outboard through ther entre range of moton to verfy clearance. Step 5: ydraulc Tubng ydraulc Tubng (contnued) Step 7: onsole Swtch rmng the ump (contnued) IRTT arefully nspect and confrm your desred mountng locaton R mountng the stern bracket. 1. Install the U n a sutable, dry locaton that s not prone to constant drenchng or submerson. Routng & Installaton 5. The tubng s now ready to be nserted nto the U fttngs. Trm the excess tubng usng a razor tubng cutter. 1. Usng the connectors suppled S, connect the red, green and blue wrng harness to the swtch as ndcated. 2. Usng the rocker swtch, cycle the cylnder from fully retracted to fully extended several tmes. old at stall for (2) seconds n each drecton to clear any remanng ar from the system. 1. Double check the clearance for adequate space on the nsde of the transom mountng area to make sure that the bolts wll not have any obstructons. lso, be sure that you wll have plenty of room to tghten the nuts on the nsde. 2. nce the mountng locaton has been selected, place the stern bracket aganst the transom and mark the mountng holes. 4. nce all of the holes have been marked and drlled use a marne grade sealant between the stern bracket and the hull as well as around the bolts and holes. 4. e sure to keep protectve caps over the pre-nstalled fttngs to keep the U free of debrs. 3. llow enough slack n the hydraulc tubng to allow for full up and down operaton of the ower-ole shallow water anchor. Step 4: Installng ydraulc ylnder 1. Install the cylnder wth stanless steel ram towards the top of the ower-ole shallow water anchor. 2. Usng the suppled hardware and spacers mount the cylnder and ensure proper placement of the ram spacers. The larger ram spacer should be on the same sde of the cylnder as the fttngs. Stern racket Transom 3. U flud level may need to be checked after fnal prmng has been completed. IRTT nce the lnes have been routed through the rubber grommet then connect to the U and the cylnder, move the ower-ole shallow water anchor through the entre range of moton to make sure the lnes are not gong to knk, chafe, or otherwse be damaged durng normal use. Step 6: Reversng Relay 1. We recommend connectng the red (+) to the man battery cut-off swtch and the black ( ) to the negatve post on the crankng battery usng the (2) yellow rng connectors R provded. lug the blue and green wres from the reversng relay nto the blue and green wres on the U. atch the three wre plug on the reversng relay to the console swtch wrng harness. lue and reen Wres to ro ump Three Wre lug for onsole Swtch and ptonal Remote ontrol Red (+) to the man cut off swtch lack ( ) to negatve post on crankng battery S R 4. Remove the blue dust cap from the upper fttng on the cylnder, nsert the blue tube nto the upper fttng on the cylnder. Remove the black dust cap and nsert the black tube nto lower fttng on the cylnder. Use the (2) provded marne wre straps L to secure the upper blue lne to the cylnder to prevent pnchng durng use. 6. Remove the dust caps from the U. Insert the lack tubng nto the fttng labeled D (black cap) and the lue tubng nto the fttng labeled U (blue cap). 3. Do not connect the ram end of the cylnder at ths tme. Ths wll be done at the fnal step after the pump has been prmed. WRI eep all debrs out of hydraulc tubng. Use the red end caps provded when routng through the boat at all tmes. Debrs n the tubng can cause damage to the pump. 2. nce the hydraulc lnes have been routed through or over the transom, nsert the black and blue hydraulc tubes through the black mesh tubng cover T and then through the rubber grommet on the lower porton of the upper U-hannel. ump racket T 1. The hydraulc tubng can be routed over or through the transom. If the tubng s beng nstalled through the transom, drll (2) 5/16 holes above the water lne close to the stern bracket and nsert the (2) thruhull bushngs provded D. T: the pump bracket can also be wall mounted. 5. asten the stern bracket to the transom usng the lsted hardware. The rubber backed neo-bond washers are to protect the anodzed fnsh of the stern bracket. D T VR TIT. L 3. ount the pump to the bracket usng the suppled hardware. 2. Usng the suppled mountng bracket and (4) #10 screws, mount the bracket n the selected locaton. 3. arefully drll the marked holes wth a 5/16 drll bt ensurng clearance on the nsde of the transom. D 1. lace a straght edge on the bottom of the hull drectly below and centered from the desred mountng locaton. Step 3: ydraulc ump Unt (U) Vertcal ostonng Step 2: ountng the ower-ole lud ll ap Down Lne (lack) Wrng to Reversng Relay Remove ths cutout from your manual and tape to your console at the desred swtch locaton. Usng a fberglass cuttng blade cut on the outsde edge of the swtch cutout template. Up Lne (lue) Swtch utout Template ut on dotted lne Step 9: nal ssembly 1. Usng the left over 5/16 bolt and hardware attach the cylnder ram to the U-hannel wth the large ram spacer on the same sde as the fttng. Step 8: rmng the ump rmng the pump 1. fter the hydraulc lnes and wrng harness have been nstalled, remove the fll cap and fll the pump to the ULL lne wth the provded quart of reen arne bodegradable hydraulc flud. If refllng and reen arne s not avalable utomatc Transmsson flud s acceptable. Warnng: Usng any other hydraulc flud may damage your hydraulc pump and vod your warranty.

5 Installaton Tools & ardware Step 1: hoose a ountng Locaton Transom mount opton 1/2 & 9/16 Wrenches, Sockets and Ratchet lectrc or attery perated Drll our oot Straght dge arne rade Sealant Tape easure Wre utters Wre rmpers Razor Tubng utters Small unnel 9/64 & 5/16 Drll ts #2 hllps ead t or Screwdrver g Saw or Rotary Saw ty(2) 5/16 x 3.5 cylnder ram bolt ty(2) 5/16 low-profle brass lock nuts ty(4) 5/16 x 3.5 all-thread transom mount bolts D ty(2) thru-hull bushngs ty(4) 5/16 tall brass lock nuts ty(4) small D washers ty(4) cylnder ram bolt bushngs ty(4) 5/16 neo-bond washers ty(4) 5/16 fender washers ty(2) large cylnder ram spacers ty(2) small cylnder ram spacers L ty(3) marne wre tes ty(4) #10 wood screws ty(2) #6 wood screws ty(2) 3/8 mountng bolt ty(2) 3/8 neo-bond washers ty(1) mountng gasket R ty(2) rng connectors S ty(3) wre plug connectors T ty (1) 5ft black mesh tubng cover 2. The lowest pont of the ower-ole shallow water anchor wll need to be at least 4 above ths straght edge. If the ower-ole shallow water anchor s mounted lower than the 4 mnmum the vessel may experence adverse handlng effects. learance 1. If the vessel s equpped wth trm tabs make sure the ower-ole shallow water anchor wll not nterfere wth the actuators or the tabs themselves. 2. If the vessel s equpped wth 9 or less trm tabs the standard 4 mnmum mountng heght wll clear the tab. If the tabs are larger than 9 the ower-ole shallow water anchor wll need to be mounted hgher to prevent nterference. 3. Turn and tlt the outboard motor all the way n the drecton of the ower-ole shallow water anchor. ove the ower-ole shallow water anchor and outboard through ther entre range of moton to verfy clearance. Step 5: ydraulc Tubng ydraulc Tubng (contnued) Step 7: onsole Swtch rmng the ump (contnued) IRTT arefully nspect and confrm your desred mountng locaton R mountng the stern bracket. 1. Install the U n a sutable, dry locaton that s not prone to constant drenchng or submerson. Routng & Installaton 5. The tubng s now ready to be nserted nto the U fttngs. Trm the excess tubng usng a razor tubng cutter. 1. Usng the connectors suppled S, connect the red, green and blue wrng harness to the swtch as ndcated. 2. Usng the rocker swtch, cycle the cylnder from fully retracted to fully extended several tmes. old at stall for (2) seconds n each drecton to clear any remanng ar from the system. 1. Double check the clearance for adequate space on the nsde of the transom mountng area to make sure that the bolts wll not have any obstructons. lso, be sure that you wll have plenty of room to tghten the nuts on the nsde. 2. nce the mountng locaton has been selected, place the stern bracket aganst the transom and mark the mountng holes. 4. nce all of the holes have been marked and drlled use a marne grade sealant between the stern bracket and the hull as well as around the bolts and holes. 4. e sure to keep protectve caps over the pre-nstalled fttngs to keep the U free of debrs. 3. llow enough slack n the hydraulc tubng to allow for full up and down operaton of the ower-ole shallow water anchor. Step 4: Installng ydraulc ylnder 1. Install the cylnder wth stanless steel ram towards the top of the ower-ole shallow water anchor. 2. Usng the suppled hardware and spacers mount the cylnder and ensure proper placement of the ram spacers. The larger ram spacer should be on the same sde of the cylnder as the fttngs. Stern racket Transom 3. U flud level may need to be checked after fnal prmng has been completed. IRTT nce the lnes have been routed through the rubber grommet then connect to the U and the cylnder, move the ower-ole shallow water anchor through the entre range of moton to make sure the lnes are not gong to knk, chafe, or otherwse be damaged durng normal use. Step 6: Reversng Relay 1. We recommend connectng the red (+) to the man battery cut-off swtch and the black ( ) to the negatve post on the crankng battery usng the (2) yellow rng connectors R provded. lug the blue and green wres from the reversng relay nto the blue and green wres on the U. atch the three wre plug on the reversng relay to the console swtch wrng harness. lue and reen Wres to ro ump Three Wre lug for onsole Swtch and ptonal Remote ontrol Red (+) to the man cut off swtch lack ( ) to negatve post on crankng battery S R 4. Remove the blue dust cap from the upper fttng on the cylnder, nsert the blue tube nto the upper fttng on the cylnder. Remove the black dust cap and nsert the black tube nto lower fttng on the cylnder. Use the (2) provded marne wre straps L to secure the upper blue lne to the cylnder to prevent pnchng durng use. 6. Remove the dust caps from the U. Insert the lack tubng nto the fttng labeled D (black cap) and the lue tubng nto the fttng labeled U (blue cap). 3. Do not connect the ram end of the cylnder at ths tme. Ths wll be done at the fnal step after the pump has been prmed. WRI eep all debrs out of hydraulc tubng. Use the red end caps provded when routng through the boat at all tmes. Debrs n the tubng can cause damage to the pump. 2. nce the hydraulc lnes have been routed through or over the transom, nsert the black and blue hydraulc tubes through the black mesh tubng cover T and then through the rubber grommet on the lower porton of the upper U-hannel. ump racket T 1. The hydraulc tubng can be routed over or through the transom. If the tubng s beng nstalled through the transom, drll (2) 5/16 holes above the water lne close to the stern bracket and nsert the (2) thruhull bushngs provded D. T: the pump bracket can also be wall mounted. 5. asten the stern bracket to the transom usng the lsted hardware. The rubber backed neo-bond washers are to protect the anodzed fnsh of the stern bracket. D T VR TIT. L 3. ount the pump to the bracket usng the suppled hardware. 2. Usng the suppled mountng bracket and (4) #10 screws, mount the bracket n the selected locaton. 3. arefully drll the marked holes wth a 5/16 drll bt ensurng clearance on the nsde of the transom. D 1. lace a straght edge on the bottom of the hull drectly below and centered from the desred mountng locaton. Step 3: ydraulc ump Unt (U) Vertcal ostonng Step 2: ountng the ower-ole lud ll ap Down Lne (lack) Wrng to Reversng Relay Remove ths cutout from your manual and tape to your console at the desred swtch locaton. Usng a fberglass cuttng blade cut on the outsde edge of the swtch cutout template. Up Lne (lue) Swtch utout Template ut on dotted lne Step 9: nal ssembly 1. Usng the left over 5/16 bolt and hardware attach the cylnder ram to the U-hannel wth the large ram spacer on the same sde as the fttng. Step 8: rmng the ump rmng the pump 1. fter the hydraulc lnes and wrng harness have been nstalled, remove the fll cap and fll the pump to the ULL lne wth the provded quart of reen arne bodegradable hydraulc flud. If refllng and reen arne s not avalable utomatc Transmsson flud s acceptable. Warnng: Usng any other hydraulc flud may damage your hydraulc pump and vod your warranty.

6 Installaton Tools & ardware Step 1: hoose a ountng Locaton Transom mount opton 1/2 & 9/16 Wrenches, Sockets and Ratchet lectrc or attery perated Drll our oot Straght dge arne rade Sealant Tape easure Wre utters Wre rmpers Razor Tubng utters Small unnel 9/64 & 5/16 Drll ts #2 hllps ead t or Screwdrver g Saw or Rotary Saw ty(2) 5/16 x 3.5 cylnder ram bolt ty(2) 5/16 low-profle brass lock nuts ty(4) 5/16 x 3.5 all-thread transom mount bolts D ty(2) thru-hull bushngs ty(4) 5/16 tall brass lock nuts ty(4) small D washers ty(4) cylnder ram bolt bushngs ty(4) 5/16 neo-bond washers ty(4) 5/16 fender washers ty(2) large cylnder ram spacers ty(2) small cylnder ram spacers L ty(3) marne wre tes ty(4) #10 wood screws ty(2) #6 wood screws ty(2) 3/8 mountng bolt ty(2) 3/8 neo-bond washers ty(1) mountng gasket R ty(2) rng connectors S ty(3) wre plug connectors T ty (1) 5ft black mesh tubng cover 2. The lowest pont of the ower-ole shallow water anchor wll need to be at least 4 above ths straght edge. If the ower-ole shallow water anchor s mounted lower than the 4 mnmum the vessel may experence adverse handlng effects. learance 1. If the vessel s equpped wth trm tabs make sure the ower-ole shallow water anchor wll not nterfere wth the actuators or the tabs themselves. 2. If the vessel s equpped wth 9 or less trm tabs the standard 4 mnmum mountng heght wll clear the tab. If the tabs are larger than 9 the ower-ole shallow water anchor wll need to be mounted hgher to prevent nterference. 3. Turn and tlt the outboard motor all the way n the drecton of the ower-ole shallow water anchor. ove the ower-ole shallow water anchor and outboard through ther entre range of moton to verfy clearance. Step 5: ydraulc Tubng ydraulc Tubng (contnued) Step 7: onsole Swtch rmng the ump (contnued) IRTT arefully nspect and confrm your desred mountng locaton R mountng the stern bracket. 1. Install the U n a sutable, dry locaton that s not prone to constant drenchng or submerson. Routng & Installaton 5. The tubng s now ready to be nserted nto the U fttngs. Trm the excess tubng usng a razor tubng cutter. 1. Usng the connectors suppled S, connect the red, green and blue wrng harness to the swtch as ndcated. 2. Usng the rocker swtch, cycle the cylnder from fully retracted to fully extended several tmes. old at stall for (2) seconds n each drecton to clear any remanng ar from the system. 1. Double check the clearance for adequate space on the nsde of the transom mountng area to make sure that the bolts wll not have any obstructons. lso, be sure that you wll have plenty of room to tghten the nuts on the nsde. 2. nce the mountng locaton has been selected, place the stern bracket aganst the transom and mark the mountng holes. 4. nce all of the holes have been marked and drlled use a marne grade sealant between the stern bracket and the hull as well as around the bolts and holes. 4. e sure to keep protectve caps over the pre-nstalled fttngs to keep the U free of debrs. 3. llow enough slack n the hydraulc tubng to allow for full up and down operaton of the ower-ole shallow water anchor. Step 4: Installng ydraulc ylnder 1. Install the cylnder wth stanless steel ram towards the top of the ower-ole shallow water anchor. 2. Usng the suppled hardware and spacers mount the cylnder and ensure proper placement of the ram spacers. The larger ram spacer should be on the same sde of the cylnder as the fttngs. Stern racket Transom 3. U flud level may need to be checked after fnal prmng has been completed. IRTT nce the lnes have been routed through the rubber grommet then connect to the U and the cylnder, move the ower-ole shallow water anchor through the entre range of moton to make sure the lnes are not gong to knk, chafe, or otherwse be damaged durng normal use. Step 6: Reversng Relay 1. We recommend connectng the red (+) to the man battery cut-off swtch and the black ( ) to the negatve post on the crankng battery usng the (2) yellow rng connectors R provded. lug the blue and green wres from the reversng relay nto the blue and green wres on the U. atch the three wre plug on the reversng relay to the console swtch wrng harness. lue and reen Wres to ro ump Three Wre lug for onsole Swtch and ptonal Remote ontrol Red (+) to the man cut off swtch lack ( ) to negatve post on crankng battery S R 4. Remove the blue dust cap from the upper fttng on the cylnder, nsert the blue tube nto the upper fttng on the cylnder. Remove the black dust cap and nsert the black tube nto lower fttng on the cylnder. Use the (2) provded marne wre straps L to secure the upper blue lne to the cylnder to prevent pnchng durng use. 6. Remove the dust caps from the U. Insert the lack tubng nto the fttng labeled D (black cap) and the lue tubng nto the fttng labeled U (blue cap). 3. Do not connect the ram end of the cylnder at ths tme. Ths wll be done at the fnal step after the pump has been prmed. WRI eep all debrs out of hydraulc tubng. Use the red end caps provded when routng through the boat at all tmes. Debrs n the tubng can cause damage to the pump. 2. nce the hydraulc lnes have been routed through or over the transom, nsert the black and blue hydraulc tubes through the black mesh tubng cover T and then through the rubber grommet on the lower porton of the upper U-hannel. ump racket T 1. The hydraulc tubng can be routed over or through the transom. If the tubng s beng nstalled through the transom, drll (2) 5/16 holes above the water lne close to the stern bracket and nsert the (2) thruhull bushngs provded D. T: the pump bracket can also be wall mounted. 5. asten the stern bracket to the transom usng the lsted hardware. The rubber backed neo-bond washers are to protect the anodzed fnsh of the stern bracket. D T VR TIT. L 3. ount the pump to the bracket usng the suppled hardware. 2. Usng the suppled mountng bracket and (4) #10 screws, mount the bracket n the selected locaton. 3. arefully drll the marked holes wth a 5/16 drll bt ensurng clearance on the nsde of the transom. D 1. lace a straght edge on the bottom of the hull drectly below and centered from the desred mountng locaton. Step 3: ydraulc ump Unt (U) Vertcal ostonng Step 2: ountng the ower-ole lud ll ap Down Lne (lack) Wrng to Reversng Relay Remove ths cutout from your manual and tape to your console at the desred swtch locaton. Usng a fberglass cuttng blade cut on the outsde edge of the swtch cutout template. Up Lne (lue) Swtch utout Template ut on dotted lne Step 9: nal ssembly 1. Usng the left over 5/16 bolt and hardware attach the cylnder ram to the U-hannel wth the large ram spacer on the same sde as the fttng. Step 8: rmng the ump rmng the pump 1. fter the hydraulc lnes and wrng harness have been nstalled, remove the fll cap and fll the pump to the ULL lne wth the provded quart of reen arne bodegradable hydraulc flud. If refllng and reen arne s not avalable utomatc Transmsson flud s acceptable. Warnng: Usng any other hydraulc flud may damage your hydraulc pump and vod your warranty.

7 Installaton Tools & ardware Step 1: hoose a ountng Locaton Transom mount opton 1/2 & 9/16 Wrenches, Sockets and Ratchet lectrc or attery perated Drll our oot Straght dge arne rade Sealant Tape easure Wre utters Wre rmpers Razor Tubng utters Small unnel 9/64 & 5/16 Drll ts #2 hllps ead t or Screwdrver g Saw or Rotary Saw ty(2) 5/16 x 3.5 cylnder ram bolt ty(2) 5/16 low-profle brass lock nuts ty(4) 5/16 x 3.5 all-thread transom mount bolts D ty(2) thru-hull bushngs ty(4) 5/16 tall brass lock nuts ty(4) small D washers ty(4) cylnder ram bolt bushngs ty(4) 5/16 neo-bond washers ty(4) 5/16 fender washers ty(2) large cylnder ram spacers ty(2) small cylnder ram spacers L ty(3) marne wre tes ty(4) #10 wood screws ty(2) #6 wood screws ty(2) 3/8 mountng bolt ty(2) 3/8 neo-bond washers ty(1) mountng gasket R ty(2) rng connectors S ty(3) wre plug connectors T ty (1) 5ft black mesh tubng cover 2. The lowest pont of the ower-ole shallow water anchor wll need to be at least 4 above ths straght edge. If the ower-ole shallow water anchor s mounted lower than the 4 mnmum the vessel may experence adverse handlng effects. learance 1. If the vessel s equpped wth trm tabs make sure the ower-ole shallow water anchor wll not nterfere wth the actuators or the tabs themselves. 2. If the vessel s equpped wth 9 or less trm tabs the standard 4 mnmum mountng heght wll clear the tab. If the tabs are larger than 9 the ower-ole shallow water anchor wll need to be mounted hgher to prevent nterference. 3. Turn and tlt the outboard motor all the way n the drecton of the ower-ole shallow water anchor. ove the ower-ole shallow water anchor and outboard through ther entre range of moton to verfy clearance. Step 5: ydraulc Tubng ydraulc Tubng (contnued) Step 7: onsole Swtch rmng the ump (contnued) IRTT arefully nspect and confrm your desred mountng locaton R mountng the stern bracket. 1. Install the U n a sutable, dry locaton that s not prone to constant drenchng or submerson. Routng & Installaton 5. The tubng s now ready to be nserted nto the U fttngs. Trm the excess tubng usng a razor tubng cutter. 1. Usng the connectors suppled S, connect the red, green and blue wrng harness to the swtch as ndcated. 2. Usng the rocker swtch, cycle the cylnder from fully retracted to fully extended several tmes. old at stall for (2) seconds n each drecton to clear any remanng ar from the system. 1. Double check the clearance for adequate space on the nsde of the transom mountng area to make sure that the bolts wll not have any obstructons. lso, be sure that you wll have plenty of room to tghten the nuts on the nsde. 2. nce the mountng locaton has been selected, place the stern bracket aganst the transom and mark the mountng holes. 4. nce all of the holes have been marked and drlled use a marne grade sealant between the stern bracket and the hull as well as around the bolts and holes. 4. e sure to keep protectve caps over the pre-nstalled fttngs to keep the U free of debrs. 3. llow enough slack n the hydraulc tubng to allow for full up and down operaton of the ower-ole shallow water anchor. Step 4: Installng ydraulc ylnder 1. Install the cylnder wth stanless steel ram towards the top of the ower-ole shallow water anchor. 2. Usng the suppled hardware and spacers mount the cylnder and ensure proper placement of the ram spacers. The larger ram spacer should be on the same sde of the cylnder as the fttngs. Stern racket Transom 3. U flud level may need to be checked after fnal prmng has been completed. IRTT nce the lnes have been routed through the rubber grommet then connect to the U and the cylnder, move the ower-ole shallow water anchor through the entre range of moton to make sure the lnes are not gong to knk, chafe, or otherwse be damaged durng normal use. Step 6: Reversng Relay 1. We recommend connectng the red (+) to the man battery cut-off swtch and the black ( ) to the negatve post on the crankng battery usng the (2) yellow rng connectors R provded. lug the blue and green wres from the reversng relay nto the blue and green wres on the U. atch the three wre plug on the reversng relay to the console swtch wrng harness. lue and reen Wres to ro ump Three Wre lug for onsole Swtch and ptonal Remote ontrol Red (+) to the man cut off swtch lack ( ) to negatve post on crankng battery S R 4. Remove the blue dust cap from the upper fttng on the cylnder, nsert the blue tube nto the upper fttng on the cylnder. Remove the black dust cap and nsert the black tube nto lower fttng on the cylnder. Use the (2) provded marne wre straps L to secure the upper blue lne to the cylnder to prevent pnchng durng use. 6. Remove the dust caps from the U. Insert the lack tubng nto the fttng labeled D (black cap) and the lue tubng nto the fttng labeled U (blue cap). 3. Do not connect the ram end of the cylnder at ths tme. Ths wll be done at the fnal step after the pump has been prmed. WRI eep all debrs out of hydraulc tubng. Use the red end caps provded when routng through the boat at all tmes. Debrs n the tubng can cause damage to the pump. 2. nce the hydraulc lnes have been routed through or over the transom, nsert the black and blue hydraulc tubes through the black mesh tubng cover T and then through the rubber grommet on the lower porton of the upper U-hannel. ump racket T 1. The hydraulc tubng can be routed over or through the transom. If the tubng s beng nstalled through the transom, drll (2) 5/16 holes above the water lne close to the stern bracket and nsert the (2) thruhull bushngs provded D. T: the pump bracket can also be wall mounted. 5. asten the stern bracket to the transom usng the lsted hardware. The rubber backed neo-bond washers are to protect the anodzed fnsh of the stern bracket. D T VR TIT. L 3. ount the pump to the bracket usng the suppled hardware. 2. Usng the suppled mountng bracket and (4) #10 screws, mount the bracket n the selected locaton. 3. arefully drll the marked holes wth a 5/16 drll bt ensurng clearance on the nsde of the transom. D 1. lace a straght edge on the bottom of the hull drectly below and centered from the desred mountng locaton. Step 3: ydraulc ump Unt (U) Vertcal ostonng Step 2: ountng the ower-ole lud ll ap Down Lne (lack) Wrng to Reversng Relay Remove ths cutout from your manual and tape to your console at the desred swtch locaton. Usng a fberglass cuttng blade cut on the outsde edge of the swtch cutout template. Up Lne (lue) Swtch utout Template ut on dotted lne Step 9: nal ssembly 1. Usng the left over 5/16 bolt and hardware attach the cylnder ram to the U-hannel wth the large ram spacer on the same sde as the fttng. Step 8: rmng the ump rmng the pump 1. fter the hydraulc lnes and wrng harness have been nstalled, remove the fll cap and fll the pump to the ULL lne wth the provded quart of reen arne bodegradable hydraulc flud. If refllng and reen arne s not avalable utomatc Transmsson flud s acceptable. Warnng: Usng any other hydraulc flud may damage your hydraulc pump and vod your warranty.

8 Three (3) YR LIITD WRRTY ower-ole Sportsman Seres shallow water anchor ower-ole Sportsman Seres shallow water anchor manufactured by L arne systems Inc. s warranted aganst defects n materal and workmanshp n the stern bracket, U-channels, nuckle jont, hydraulc system, and electrcal system, to the orgnal owner accordng to the followng stpulatons: 1. ower-ole Sportsman Seres shallow water anchor warrantes are actvated upon recept by L arne Systems, Inc. of the completed warranty card, postdated wthn (10) days of purchase or by regsterng your ower-ole shallow water anchor on our webste. lease retan your sales recept as proof of purchase. 2. Install enune ower-ole erchandse LY. Ths warranty s vod f any non authorzed parts are used or nstalled. 3. Ths warranty s vod f the ower-ole Sportsman Seres shallow water anchor s used commercally, structurally altered or subject to stress beyond the physcal lmts of the manufactured materal. 4. Ths warranty does not cover abrason or abnormal abuse, nor does t cover the ower-ole shallow water anchor for anythng other than ts ntended use. 5. L arne Systems, Inc. reserves the rght to change products and desgns wthout ncurrng any oblgatons to ncorporate such changes n already completed products, or those n the hands of dealers or consumers. roducts repared or replaced under ths warranty may or may not have these changes. Shppng (nly apples to packages shpped wthn the ontnental U.S.) 1. arts whch prove defectve wthn (90) days from the date of purchase, L arne Systems, Inc. wll pay for the replacement product shppng and handlng fees to and from the L arne Systems, Inc. manufacturng plant or some other place whch L arne Systems, Inc. mght desgnate. 2. arts whch prove defectve after (90) days but before (12) months from the date of purchase wll also be repared or replaced free of charge, but there may be a shppng charge to L arne Systems, Inc. manufacturng plant or some other place whch L arne Systems, Inc. mght desgnate. 3. arts whch prove defectve after (12) months wll also be repared or replaced free of charge, but there may be a shppng and handlng charge to and from the L arne Systems, Inc. manufacturng plant or some other place whch L arne Systems, Inc. mght desgnate. arts 1. Stern bracket, U-channel, or nuckle jont, whch proves defectve before sxty (36) months, wll be repared or replaced free of charge. In the case of replacement, parts of same (or equvalent) model wll be used. 2. The ydraulc ower Unt (Sportsman ump) whch proves defectve wthn (24) months from date of purchase wll be repared or replaced free of charge. ump damage due to ncorrect hydraulc flud, submerson or excessve exposure to water may vod ths warranty. 3. ylnder or tubng whch proves defectve wthn (24) months from date of purchase wll be repared or replaced free of charge. In the case of replacement, parts of same (or equvalent) model wll be used. 4. reversng relay, swtches, or wrng harness whch proves defectve wthn (24) months from date of purchase wll be repared or replaced free of charge. 5. Spke uncondtonal lfetme guarantee. 6. Ths Warranty does not cover water damage n any way. T WRRTY TID RI IS T XLUSIV WRRTY D Y L arne Systems, Inc. D TR R TR WRRTIS, XRSSD R ILID, ILUDI WRRTY ITSS R RTIULR URS R RTILITY D WIT RST T SU RS. L RI SYSTS, I. IS T LIL R Y IURY R ISS SUSTID I T US TIS RDUT. T USR TIS RDUT WLDS SSUD RISS D WIVS Y D LL LIS IST L arne Systems, Inc. D Y IT S TS. Ths warranty apples under condtons of normal use. The warranty does not cover: 1) defects caused by mproper assembly or dsassembly; 2) defects occurrng after purchase due to product modfcaton, ntentonal damage, accdent, msuse, abuse, neglgence or exposure to corrosve elements; 3) cosmetc damage and 4) labor or assembly costs. xcept as provded heren, L arne Systems, Inc. makes no express warrantes, and any mpled warranty, ncludng wthout lmtaton any mpled warranty of merchantablty or ftness for a partcular purpose, s lmted n ts duraton to the duraton of the wrtten lmted warranty set forth heren. xcept as provded heren, L arne Systems, Inc. shall have no lablty or responsblty to the purchaser or any other person or entty wth respect to any lablty, loss or damage caused or alleged to be caused drectly or ndrectly by use of the product, ncludng, but not lmted to, any ncdental or consequental damages. Some states do not allow lmtaton on how long an mpled warranty lasts or the excluson of lmtaton of ncdental or consequental damages, so the above lmtaton and excluson may not apply to you. Ths warranty gves you specfc legal rghts. You may also have other rghts whch vary from state to state alm Rver Road, Sute 303, Tampa, lorda hone ax