Installation S19-120BF S19-120ABF. Plastic Showerhead. Plastic Showerhead with Stainless Steel Shroud Drench Shower - Horizontal Supply

Transcription

1 S19-10BF Plastic Showerhead S19-10ABF Plastic Showerhead with Stainless Steel Shroud Drench Shower - Horizontal Supply Table of Contents Pre- Information... Supplies Required... Assemble components... Connect water supply... Assembly of Components - S19-10BF... Parts List... Assembly of Components - S19-10ABF... Parts List Rev. F; ECN Bradley Page 1 of 7/18/017 P.O. Box 09 Menomonee Falls, WI 0 USA 800 BRADLEY ( ) bradleycorp.com

2 S19-10BF, S19-10ABF WARNING Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. CAUTION Emergency equipment must be supplied with tepid water (60 F to 100 F/1.6 C to 7.8 C). Any prolonged exposure to near freezing water affects the body's ability to maintain body temperature, increasing the risk of hypothermia. NOTICE Before installing this product, ensure that there are adequate clearances around the product and activation of the product does not interfere with other products or obstructions. Avoid cleaners containing organic solvents, alcohols and hydrocarbons. Rinse with water after cleaning. IMPORTANT The installation and location of all safety drench showers, eye and eye/face washes must comply with the requirements of ANSI/ISEA Z8.1. Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. The ANSI/ISEA Z8.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed emergency fixtures require a minimum of 0 PSI (0.1MPa) flowing pressure. Self-closing spring-loaded valves are not UL classified to ANSI/ISEA Z8.1. Weekly activation must be conducted on all plumbed emergency equipment to ensure a suitable flushing fluid supply is present and any sediment build-up in the supply line is cleared. Emergency equipment should be inspected monthly to address any maintenance issues ensuring the equipment is in good operating condition and that there are no signs of wear. Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI/ISEA Z8.1. For questions regarding the operation or installation of this product, visit or call 800-BRADLEY (7.9). Product warranties and parts information may also be found under Products on our web site at bradleycorp.com. 7/18/017 Bradley 1-19 Rev. F; ECN

3 S19-10BF, S19-10ABF Supplies Required Teflon tape and pipe sealant Piping to 1" NPT water supply inlet Adequate supply pipe supports Minimum " (10 mm) drain to accommodate 0 gallons (11 liters) per minute discharge for shower waste -1/" (11mm) " (610mm) 8" (0mm) -/8" (9mm) Sign-mounting hardware Assemble components 1. Assemble components as shown on page.. Apply pipe sealant (supplied by installer) to all male-threaded pipe joints. 7'-0" (1mm) to Floor Ø.1" (78.7mm) " (11mm). Thread the jam nut onto the threaded end of the pull rod. Thread the pull rod onto the coupling and tighten the jam nut. The triangular end of the pull rod must be in line with the hook end (see page ).. Bottom edge of showerhead should be 7'-0" (1 mm) from the floor. Connect water supply NOTICE! Do not rely on Bradley s Drench Shower to support supply piping. 9" (9mm) S19-10BF 1. Connect water supply piping to 1" NPT inlet on unit (piping supplied by installer). Provide adequate supports (supplied by installer) for supply pipe using pipe hangers or other means.. Mount the safety sign to the wall using signmounting hardware supplied by installer. 6" (1mm) " (610mm) 8" (0mm) -/8" (9mm) 7'-0" (1mm) to Floor Ø 10-/" (7mm) " (11mm) 9" (9mm) S19-10ABF Bradley 1-19 Rev. F; ECN /18/017

4 11-00 P.O. BOX 09, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) R P.O. Box 09, Menomonee Falls, WI 01 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Date Signed Date Signed Datum Unterschrift Date Signed Date Signe Date Signed S19-10BF, S19-10ABF Assembly of Components - S19-10BF " NPT Supply Inlet NOTE: Use teflon tape only. 6 7 ALIGN HANDLE PIECES AS SHOWN Parts List 1 S " Stay-Open Ball Valve Assembly Washer, Friction 1. S " Ball Valve with Nut Jam Nut Only Adapter Handle MT 1 Pipe 1" NPT x 1" Elbow 1" NPT S Plastic Showerhead Assembly Curtain Hook 6 S90-6D 1 Pull Rod, " Nut, 1/" Emergency Inspection Tag Safety Sign 7/18/017 Bradley 1-19 Rev. F; ECN

5 11-00 P.O. BOX 09, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) R P.O. Box 09, Menomonee Falls, WI 01 TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Date Signed Date Signed Datum Unterschrift Date Signed Date Signe Date Signed S19-10BF, S19-10ABF Assembly of Components - S19-10ABF " NPT Supply Inlet ALIGN HANDLE PIECES AS SHOWN NOTE: Use teflon tape only. Parts List 1 S " Stay-Open Ball Valve Assembly Washer, Friction 1. S " Ball Valve with Nut Jam Nut Only Adapter Handle MT 1 Pipe 1" NPT x 1" Elbow 1" NPT S Stainless Steel Showerhead Assembly.1 S-19 1 Showerhead Shell Kit Showerhead Shell Ring. S Plastic Showerhead Assembly Curtain Hook 6 S90-6D 1 Pull Rod, " Nut, 1/" Emergency Inspection Tag Safety Sign Bradley 1-19 Rev. F; ECN /18/017