OBSOLETE. Installation S19-325BF S19-325FBF S19-325PBF S19-325FPBF

Transcription

1 EMERGENCY EYEWASH PULL HANDLE TO ACTIVATE UNIT USH TO TIVATE HOWER USH S19-325BF S19-325FBF S19-325BF S19-325FBF S19-325PBF S19-325FPBF Barrier Free Recess-Mounted Drench Shower with Barrier Free Cabinet-Concealed Swing-Down Eye/Face Wash Table of Contents Pre- Information Dimensions Rough-Ins... 4 Instructions Drench Shower Components and Parts List... 7 Eye/Face Wash Components Eye/Face Wash Parts List TO TIVATE HOWER Rev. F; ECN Bradley Page 1 of 10 5/12/2014 P.O. Box 309, Menomonee Falls, WI USA PHONE 800.BRADLEY ( ) FAX bradleycorp.com

2 R Datum Signe P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF IMPORTANT Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. THIS SIDE UP Packing List Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Unterschrift Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. The ANSI Z358.1 standard requires an uninterrupted supply of flushing fluid. Bradley plumbed emergency fixtures require a minimum of 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI Z The inspection and testing results of this equipment should be recorded weekly to verify proper operation. This equipment should be inspected annually to ensure compliance with ANSI Z Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI Z For questions regarding the operation or installation of this product, visit com or call BRADLEY. Product warranties and parts information may also be found under Products on our web site at NOTICE! Avoid cleaners containing organic solvents, alcohols, and hydrocarbons. Rinse with water after cleaning. Local codes may require the installation of a backflow prevention valve to complete proper installation. Compliance with local codes is the responsibility of the installer. Valve must be tested annually to verify that it is functioning properly. Backflow prevention valves are not included with the fixture and may be supplied by the contractor or purchased from Bradley Corporation. 2 5/12/2014 Bradley Rev. F; ECN

3 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF Eye/Face Wash Cabinet Dimensions Side View Front View Side View ⁷ ₈" (22mm) 27⁵ ₈" (702mm) 6" (152mm) 1⁷ ₈" (48mm) 25½" (648mm) 33⁵ ₈" (854mm) 3¹ ₁₆" (78mm) Ø 1¼" (32mm) Waste Ø 1" (25mm) nominal copper tube supply Bottom View 1" (25mm) NPT to showerhead 22¾" (578mm) 15⁹ ₁₆" (395mm) 17⁷ ₁₆" 29⁷ ₁₆" (443mm 748mm) to floor for ANSI compliance 17⁷ ₁₆" 21⁷ ₁₆" (443mm 545mm) to floor for barrier free compliance 1¾" (44mm) Ø ¼" mounting hole (qty. 4) 22³ ₈" (568mm) 1¹ ₈" (29mm) 29¹ ₈" (740mm) 2¹ ₁₆" (52mm) 6³ ₈" (162mm) Bradley Rev. F; ECN /12/2014 3

4 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF 1 Rough-Ins ceiling hole Ø 1½" (38mm) ceiling hole Ø 5" (127mm) S19-325BF S19-325PBF S19-325FBF S19-325FPBF Piping and adequate supports by installer 4⁵ ₁₆" (110mm) 25" (635mm) min. 82 to 96" (2083mm to 2438mm) to floor Piping and adequate supports by installer 4⁵ ₁₆" (110mm) 25" (635mm) min. 6" (152mm) min. clearance 82 to 96" (2083mm to 2438mm) to floor Wall Opening 25⁵ ₈" (651mm) wide 32¹ ₈" (816mm) high 4 5/12/2014 Bradley Rev. F; ECN

5 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF 2 Piping and adequate supports by installer Piping and adequate supports by installer S19-325BF S19-325PBF Supplied by installer NOTE: Use teflon tape only. S19-325FBF S19-325FPBF NOTE: Use teflon tape only. Secure cabinet to wall, four places. Bradley Rev. F; ECN /12/2014 5

6 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF 3 Connect Water Supplly Mount safety sign to wall. To showerhead Connect 1" NPT supply piping Exploded view of valve and handle assembly 6 5/12/2014 Bradley Rev. F; ECN

7 R P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF Assembly of Components and Parts List for Drench Shower (S19-325BF OR S19-325PBF) (S19-325BF or S19-325PBF) Service Prepacks Datum Unterschrift Signe (S19-325BF OR S19-325PBF) Valve Mounting Hardware Prepack (includes Valve Mounting Bracket, U-Bolt, Nuts and Washers) S S (S19-325BF or S19-325PBF) S (S19-325FBF or S19-325FPBF) Screw Prepack (includes twelve screws and Torx Power Bit) S Valve/Handle Prepack (includes Handle and Valve Assembly) S Bradley Rev. F; ECN /12/2014 7

8 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF Assembly of Components for Eye/Face Wash (parts list on page 10) 1g 1s 1d 1k 1b 1e 1a Items 1a-1p and Items come preassembled as Item 1. 1c 1f Shown in the ON position. 1h 1j 10 (Tailpiece) or 1p 1l 1m 1n (Tubular Trap) 8 5/12/2014 Bradley Rev. F; ECN

9 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF Assembly of Components for Eye/Face Wash continued Bradley Rev. F; ECN /12/2014 9

10 S19-325BF, S19-325FBF, S19-325PBF, S19-325FPBF Parts List for Eye/Face Wash Item Part No. Qty. Description 1 S Swing-Down Sub-Assembly 1a S Eye/Face Wash Yoke Assembly 1b Pipe - Plated 1c Valve Body - Plated 1d O-Ring 1e O-Ring 1f Insert, Direction - Plated 1g Screw, Set 1h S Actuator Sub-Assembly - Valve 1i Insert, Flow Control 1j CS 1 O-Ring 1k Flow Control 1l A 1 Hex Nut - Plated 1m DA 1 O-Ring 1n Base Item Part No. Qty. Description 2 S Cabinet Assembly 3 S Handle/Hardware Kit 4 S Swing-Down Stop Kit Rod End Spacer Bracket, Swing-Down Decal, Pull Down Eyewash Decal, Concealed Eyewash Tailpiece or Tubular Trap, 1-1/4" Gas Spring Bolt, 5/16"-18 x 1" Bolt, 5/16"-18 x 3/4" 14 S Stop Valve 1p Screw, Set Union 1q Shank /2" Elbow, 90 1r Hex Nut CB 1 Washer 1s S Eye/Face Wash Assembly 10 5/12/2014 Bradley Rev. F; ECN