Installation S19-220ABF S19-220BBF. Wall-Mounted Barrier Free Eyewash with Plastic Bowl. Wall-Mounted Barrier Free Eyewash with Stainless Steel Bowl

Transcription

1 S19-220ABF Wall-Mounted Barrier Free Eyewash with Plastic Bowl S19-220BBF Wall-Mounted Barrier Free Eyewash with Stainless Steel Bowl Table of Contents Pre- Information Instructions Dimensions and Rough-ins Plastic Bowl Assembly of Components Parts List Stainless Steel Bowl Assembly of Components Parts List ABF Rev. H; EN E 2007 Bradley Corporation Page 1 of 6 6/19/07 P.O. Box 309, Menomonee Falls, WI USA PHONE BRADLEY FAX (262)

2 R Datum Signe P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Signed Unterschrift Signed Signed Signed THIS SIDE UP! Packing List WARNING Read this installation manual completely to ensure proper installation, then file it with the owner or maintenance department. Compliance and conformity to drain requirements and other local codes and ordinances is the responsibility of the installer. Separate parts from packaging and make sure all parts are accounted for before discarding any packaging material. If any parts are missing, do not begin installation until you obtain the missing parts. Flush the water supply lines before beginning installation and after installation is complete. Test the unit for leaks and adequate water flow. Main water supply to the eyewash should be ON at all times. Provisions shall be made to prevent unauthorized shutoff. The ANSI Z358.1 standard requires an uninterruptible supply of flushing fluid at a minimum 30 PSI (0.21 MPa) flowing pressure. Flushing fluid should be tepid per ANSI Z The inspection and testing results of this equipment should be recorded weekly to verify proper operation. This equipment should be inspected annually to ensure compliance with ANSI Z Workers who may come in contact with potentially hazardous materials should be trained regarding the placement and proper operation of emergency equipment per ANSI Z For questions regarding the operation or installation of this product, visit or call BRADLEY. Product warranties may also be found under Product Information on our web site at 2 4/16/07 Bradley Corporation ABF Rev. H; EN E

3 NOTE: Refer to the dimensions and rough-ins shown on page 4. Supplies Required: (4) 3/8" bolts and wall anchors for mounting wall bracket Pipe sealant Piping to 1/2" NPT water supply inlet on unit Piping to 1-1/4" NPT drain outlet for eyewash Sign-mounting hardware Step 1: Install eyewash bracket NOTE: The top of the eyewash heads should be 36" (914 mm) from the floor. 1. Position the inlet drain fitting over the 1-1/4" drain outlet pipe from wall. Using the eyewash bracket as a template, mark the bolt hole locations on wall. 2. (optional) Install four suitable anchors (supplied by installer) for 3/8" bolts in the wall at the marked hole locations. 3. Bolt the eyewash bracket to the wall or wall anchors using 3/8" bolts (supplied by installer). Step 2: Assembly eyewash components 1. Assemble the remaining eyewash components as shown on page 5 (for eyewash with a plastic bowl) or page 6 (for eyewash with a stainless steel bowl). Apply pipe sealant (supplied by installer) to all male-threaded pipe joints. Use a strap wrench around pipes when tightening to prevent pipe marring. Step 3: Connect water supply 1. Connect the water supply piping (supplied by installer) to the 1/2" NPT inlet on the eyewash. 2. Connect the drain piping (supplied by installer) to the 1-1/4" NPT drain outlet on the eyewash. 3. Mount safety sign to wall using sign-mounting hardware (supplied by installer). 4. Open the water supply lines. Test for leaks and adequate water flow. Bradley Corporation ABF Rev. H; EN E 4/16/07 3

4 24-1/4" (616mm) 15-1/2" (394mm) 24-1/2" (622mm) 15-1/2" (394mm) 19-1/4" (489mm) 5-1/4" (133mm) 19-1/4" (489mm) 5-1/4" (133mm) 15-1/2" (394mm) Ø 10" (254mm) 15-7/8" (403mm) Ø 10-3/4" (273mm) 36" (914mm) 3/8" (10mm) 36" (914mm) 3/8" (10mm) 4-1/2" (114mm) 4-1/2" (114mm) 30-3/4" (781mm) 3-1/2" (89mm) Ø P-Trap Outlet 30-3/4" (781mm) 3-1/2" (89mm) Ø P-Trap Outlet 23-5/8" (600mm) 23-5/8" (600mm) S19-220ABF S19-220BBF 4 4/16/07 Bradley Corporation ABF Rev. H; EN E

5 P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) R P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Signed Signed Datum Unterschrift Signed Signe Signed Assembly of Components - S19-220ABF (Plastic Bowl) Flow Control This End /4" IPS Drain Outlet 1/2" IPS Supply Inlet 5 Figure 2a NOTE: Items come preassembled as Item 1. Item Part No. Qty Description Item Part No. Qty Description 1 S Barrier Free Wall-Mt. Eyewash 1.1 S Eyewash Bracket Gasket Plastic Eyewash Bowl Cup Strainer 1.5 S Supply Stem Spacer, Drain 1.7 S Eyewash Yoke Assembly Dust Cover Elbow 4 S /2" Ball Valve with nut Nut only Handle Assembly DA 1 Lockwasher Tailpiece P-Trap Safety Sign Emergency Tag Pipe, Stainless Steel 1/2" x 3-1/2" Prepack S includes Items 1.2, 1.4, 1.5, 1.6 Prepack S includes Items 5, 6, 4.1 Prepack S includes Items 4, 5, 6, 4.1 Bradley Corporation ABF Rev. H; EN E 4/16/07 5

6 P.O. BOX 309, MENOMONEE FALLS, WI USA TEL: BRADLEY FAX: ( ) R P.O. Box 309, Menomonee Falls, WI TEST THIS UNIT EACH WEEK DIESES GERÄT 1ST WÖCHENTLICH ZU PRÜFEN. ESSAI HEBDOMADAIRE Test-operate valve(s) each week and sign below. Report any malfunctions immediately. Ventil(e) wöchentlich im Testbetrieb prüfen, bestätigt durch Unterschrift. Jegliche Störung sofort melden. Test le fonctionnement des valves chaque semaine et signe en bas. S'il y à quelque chose qui ne va pas fait un rapport immédiatement. Signed Signed Datum Unterschrift Signed Signe Signed Assembly of Components - S19-220BBF (Stainless Steel Bowl) Flow Control This End /4" IPS Drain Outlet 1/2" IPS Supply Inlet 5 Figure 2b NOTE: Items come preassembled as Item 1. Item Part No. Qty Description Item Part No. Qty Description 1 S Barrier Free Wall-Mt. Eyewash 1.1 S Eyewash Bracket Gasket Stainless Steel Eyewash Bowl Cup Strainer 1.5 S Supply Stem Spacer, Drain 1.7 S Eyewash Yoke Assembly Dust Cover Elbow 4 S /2" Ball Valve with nut Nut only Handle Assembly DA 1 Lockwasher Tailpiece P-Trap Safety Sign Emergency Tag Pipe, Stainless Steel 1/2" x 3-1/2" Prepack S includes Items 5, 6, 4.1 Prepack S includes Items 4, 4.1, 5, 6 Prepack S includes Items 1.2, 1.4, 1.5, /16/07 Bradley Corporation ABF Rev. H; EN E