ABS PIPES & FITTINGS THE INDUSTRY STANDARD FOR A WIDE RANGE OF APPLICATIONS
|
|
|
- Derrick Flowers
- 5 years ago
- Views:
Transcription
1 S PIPES & FITTINGS THE INDUSTRY STNDRD FOR WE RNGE OF PPLICTIONS VUX VERSION 2
2 S PIPE & FITTINGS FOR INDUSTRIL PPLICTIONS INTRODUCTION S thermoplastics are recognized as a suitable material to be used in many industry applications. The material is very tough and resilient, has high impact strength, good chemical resistance non-toxic and taint free. S piping systems are replacing many piping systems made from other materials. Pentair s S piping systems compromises a large range of pressure ratings for pipes and fittings, joined together by cold solvent cement welding. PPLICTIONS DURFLO Pipes & Fittings are widely used in a variety of applications such as: - HVC, chilled water and condenser - Water reticulation - Domestic plumbing - Water treatment plants - Waste water treatment and recycling plants - Power generation plants - Industrial plants such as electronics, food processing, chemical, paper mills, palm oils and rubber mills. DURFLO S PIPE & FITTINGS
3 TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE S is tough and strong over the recommended temperature range of -30 o C to +60 C. The formulation of S used by Euratech has been developed in conjunction with polymer manufacturers to optimise performance in respect to tensile strength, chemical resistance, ductility, resistance to weathering, heat stability, low toxicity, taint free and ease processing from raw material to finished product. THE ENVIRONMENT The use of S contributes positively to the environment as it takes approximately one sixth of the energy to manufacture compared to metal products. This has direct savings in greenhouse gas emissions. dditionally S is lead, chlorine and halogen free and can be readily recycled. THE EXPERIENCE Viadux has a highly trained and experienced team dedicated to the design, manufacture, installation and operation of its products. Viadux is committed to a program of continuous improvement in the quality and reliability of its products and services. Technical advice is available from our team. pplication advice and support is also available. DURFLO S PIPE & FITTINGS 1
4 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE THE MTERIL PRESSURE RTINGS crylonitrile utadiene Styrene (S) identifies a family of engineering thermoplastics with a board range of performance characteristics. The copolymeric system is alloyed to yield the optimum balance of properties suited to the selected end use. CRYLONITRILE imparts chemical resistance and rigidity. UTDIENE endows the product with impact strength, toughness and abrasion resistance. STYRENE contributes to the lustre, ease of processing and rigidity. DURFLO S Piping Systems are available in a range of sizes from DN 15 to DN 750. Standard pressure ratings at 20 C are 900 kpa, 1200 kpa and 1500 kpa (Class C, Class D and Class E). TEMPERTURE RNGE great advantage of DURFLO S over other plastic systems is its ability to perform over a wide temperature range from -30 C to +60 C. This makes DURFLO S very versatile and capable of handling a wide variety of fluids from refrigerants to moderately hot corrosive liquids. CHEMICL RESISTNCE DURFLO S is unaffected by both internal and external attack by a wide range of acids, alkalis, ground water salts and other environmental factors. Please refer to Viadux for further information. QUICK REFERENCE CHEMICL RESISTNCE LIGHT WEIGHT S is one-sixth the weight of steel systems, making DURFLO easy to handle and install. This reduces the cost of installation, handling and transport. COLD SOLVENT WELD JOINING The DURFLO range also utilizes the proven traditional method of joining S pipes, cold solvent cement welding, which provides a homogeneous bond/weld between pipes and fittings (SWJ). - Weak acids Good resistance - Strong acids Limited resistance - Weak alkalis Good resistance - Strong alkalis Good resistance - ggressive soils Excellent resistance - Metal salts Good resistance - Sea water Excellent resistance - romatic Poor resistance hydrocarbons - Organic solvents Poor resistance NON-TOXIC / TINT FREE The S formulation contains no harmful metallic stabilisers and has been widely used for many years in piping systems for drinking water, medical preparations, food products and potable water. The DURFLO S system is ideal for potable cold water, conforming to World Health Organisation, EU and S 4020 / S 6920 requirement for potable water reticulation and distribution. 2 DURFLO S PIPE & FITTINGS
5 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE SMOOTH ORE IMPCT STRENGTH THERML EXPNSION DURFLO S does not suffer from internal corrosion and provides a smooth bore for the life of the piping systems. The smooth bore does not support formation of scale and slime as with cement based lined products. RSION RESISTNCE DURFLO S offers outstanding resistance to abrasion and erosion from aggressive slurries which can rapidly damage steel or other traditional pipe materials. The butadiene constituent in S affords unrivalled resistance to impact. This means that DURFLO Piping systems may be used in more critical applications where other types of plastics could not be considered. S is a ductile material and the mode of failure resembles that of soft copper. Failure is by ductile distortion and tearing, the localised nature minimising the loss of pipe contents. In contrast, crack propagation and hazardous material fragmentation accompany the failure of brittle material. 25 ll thermoplastics expand at a greater rate than metal. Expansion need not cause undue concern in design or installation of an S piping system provided that due recognition is taken at the design stage. The reduced flexural modulus of S over that of steel results in reduced loads on supports and equipment arising from thermal strains. The linear coefficient of thermal expansion of S is 10.1 x 10-5 m/m C. WETHER RESISTNCE DURFLO S is one of the most weather resistance polymers available today. Successful field tests have been completed on piping systems having been exposed to weathering for over 30 years. STNDRDS IMPCT ENERGY. kg/m C 0 C 20 C DURFLO products are manufactured to conform to recognised international engineering quality standard such as ustralian Standard S/NZS Viadux is also accredited to ISO9001:2008 Quality System PIPE. mm DURFLO S PIPE & FITTINGS 3
6 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE DURFLO S PRESSURE PIPE SERIES 1 PGE 6 PLIN SOCKET 100 PGE 7 STU FLNGE 135, 134, 138 PGE 8 FULL FCE FLNGE 129, 130, 317, 322, 329 PGE 9 SHOULDER END 954 PGE 10 SHOULDER STYLE COUPLING 953 PGE 10 LNK FLNGE STU STYLE 136 PGE 11 LNK FULL FCE FLNGE 129, 313, 325, 326, 332 PGE 11 LIND STEEL PLTE 731, 732 PGE 12 LIND S LINER 721, 722 PGE 12 CKING RING 413, 415, 416, 425 PGE 13, 14, 15, 16 VLVE SUPPORT PLTE 460, 465, 470 PGE 17 GSKET FULL FCE STYLE 409, 410, 426 PGE 18 GSKET STU FLNGE STYLE 431 PGE 19 ELOW PGE 20 ELOW PGE 21 FUCET ELOW PGE 22 MOULDED END PGE 23 END 90 SHORT RDIUS 308 PGE 24 END 45 SHORT RDIUS 312 PGE 25 END 90 LONG RDIUS 309 PGE 26 END 45 LONG RDIUS 310 PGE 27 EQUL TEE SO-SOxSO 122 PGE 28 REDUCING TEE SPIGOT OFFTKE SO-SOxSP 120 PGE 29 REDUCING TEE SOCKET OFFTKE SO-SOxSO 122 PGE 30 4 DURFLO S PIPE & FITTINGS
7 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE TEE THREDED OFFTKE SO-SOxTH 121 PGE 31 Y PIECE PGE 32 SDDLE STRIP 146 PGE 33 TPPING SDDLE 127 PGE 34 REDUCING SOCKET 114 PGE 35 REDUCING USH 109 PGE 36 FUCET SOCKET 101 PGE 37 FUCET DPTOR 153 PGE 37 VLVE DPTORS 107 PGE 38 VLVE SOCKET 151 PGE 39 CPS 140 PGE 40 THREDED PLUG 155 PGE 41 SOCKET UNION 205 PGE 42 SDDLE CLIP 455 PGE 43 PIPE CLIP 434 PGE 44 RUER EXPNSION JOINT 452 PGE 45 NCHOR SLEEVE 272 PGE 46 NCHOR FLNGE 137 PGE 46 LL CHECK VLVE SINGLE UNION 836, 838 PGE 47 LL VLVE DOULE UNION 880, 882 PGE 47 COPYRIGHT S SOLVENT CEMENT 461 PGE 48 MEK CLENER/PRIMER 463 PGE 48 This manual is a publication of Viadux Pty Ltd, N , and must not be copied or reproduced in whole or part without the Company s prior written consent. This manual is and shall remain as the Company s property and shall be returned to the Company on its request. The Company reserves the right to make changes to any matter at any time without notice. ll Viadux trademarks and logos are owned by Viadux Pty Ltd. ll other brand or product names are trademarks or registered marks of their respective owners. DURFLO S PIPE & FITTINGS 5
8 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE DURFLO S PRESSURE PIPE SERIES 1 PRESSURE RTING TYPE COMPOUND CLSS PRODUCT PRESSURE OD MEN WLL MEN MEN ar mm mm mm DN 15 S1 PN 20 DURFLO S160 R DN 20 S1 PN 18 DURFLO S160 R DN 25 S1 PN 18 DURFLO S160 R DN 32 S1 PN 18 DURFLO S160 R DN 40 S1 PN 18 DURFLO S160 R *DN 50 S1 PN 12 DURFLO S160 R DN 50 S1 PN 15 DURFLO S160 R *DN 65 S1 PN 12 DURFLO S160 R DN 65 S1 PN 15 DURFLO S160 R DN 80 S1 PN 9 DURFLO S160 R *DN 80 S1 PN 12 DURFLO S160 R DN 80 S1 PN 15 DURFLO S160 R DN 100 S1 PN 9 DURFLO S160 R *DN 100 S1 PN 12 DURFLO S160 R DN 100 S1 PN 15 DURFLO S160 R *DN 125 S1 PN 9 DURFLO S160 R *DN 125 S1 PN 12 DURFLO S160 R DN 125 S1 PN 15 DURFLO S160 R DN 150 S1 PN 9 DURFLO S160 R *DN 150 S1 PN12 DURFLO S160 R DN 150 S1 PN15 DURFLO S160 R *DN 200 S1 PN 6 DURFLO S160 R DN 200 S1 PN 9 DURFLO S160 R DN 200 S1 PN15 DURFLO S160 R *DN 225 S1 PN 6 DURFLO S160 R DN 225 S1 PN 9 DURFLO S160 R DN 225 S1 PN15 DURFLO S160 R *DN 300 S1 PN 6 DURFLO S160 R DN 300 S1 PN 9 DURFLO S160 R DN 300 S1 PN15 DURFLO S160 R *DN 350 S1 PN 6 DURFLO S160 R DN 350 S1 PN 9 DURFLO S160 R DN 350 S1 PN15 DURFLO S160 R *DN 375 S1 PN 6 DURFLO S160 R DN 375 S1 PN 9 DURFLO S160 R DN 375 S1 PN 15 DURFLO S160 R *NON STOCKLE MDE TO ORDER MINIMUM QUNTITIES PPLY LRGER PIPES & FITTINGS FROM DN 400 TO DN 750 RE VILLE PRICE ON PPLICTION PIPE COMPLIES WITH S/NZS 3518 LL VLUES QUOTED RE SUJECT TO MNUFCTURING TOLERNCES STNDRD PIPE LENGTH SUPPLIED 5.8m OTHER LENGTHS ND PRESSURE RTINGS RE VILLE UPON REQUEST PIPE IS SUPPLIED PLIN ENDED 6 DURFLO S PIPE & FITTINGS
9 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE PLIN SOCKET Z Z PN mm mm mm mm RTING DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R DN 375 S1 R COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 7
10 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE STU FLNGE C D Z D* * PN mm mm mm mm mm mm mm mm RTING DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R DN 375 S1 R Z D When using the new compact stub flanges it will be important to determine what equipment they are matching up to Where the flanges are being used with butterfly valves you will need to check the chordal diameter of the valve disc (the disc chord dimension at the face of the valve) to determine if there will be a clash with the pipe Where this is likely to occur we have the 138 series stub flange which is designed to take the potential clash into account C TO SUIT CKING RING DRILLED TO JIS10K SUITS LL OTHER DRILLINGS COMPLIES WITH S/NZS SERIES STU FLNGE C D Z mm mm mm mm mm mm 200 R R R R R RNGE: DN 200 TO DN 375 TEMPERTURE RNGE: -30 C TO 60 C JOINTING METHOD: SOLVENT CEMENT COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
11 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE FULL FCE FLNGE TLE E C D Z D* PN mm mm mm mm mm mm mm RTING DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 80 S1 R DN 100 S1 R DN 150 S1 R Z D C CKING RINGS RE RECOMMENDED TO E USED WITH FULL FCE FLNGES UNDRILLED DRILLED TLE D S 2129: DRILLED NSI DRILLED JIS10K COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 9
12 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE SHOULDER END Z PN mm mm mm mm RTING DN 50 S1 R DN 80 S1 R DN 100 S1 R DN 150 S1 R Z COMPLIES WITH S/NZS 3518:2004 SHOULDER STYLE COUPLING TO SUIT PIPE Z mm mm mm DN 50 S1 R DN 80 S1 R DN 100 S1 R DN 150 S1 R C CSING - GLVNISED IRON GSKET - EDPM 10 DURFLO S PIPE & FITTINGS
13 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE LNK FLNGE STU STYLE PN 12 mm mm DN 200 S1 R DN 225 S1 R DN 300 S1 R REQUIRES CKING RING FOR LRGER S STEEL PLTES RE RECOMMENDED LNK FULL FCE FLNGE TLE E mm mm DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 80 S1 R DN 100 S1 R DN 150 S1 R CKING RINGS RE RECOMMENDED TO E USED WITH LNK FULL FCE FLNGES UNDRILLED DRILLED NSI DRILLED TLE D / S 2129: DRILLED JIS10K DURFLO S PIPE & FITTINGS 11
14 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE LIND STEEL PLTE mm mm TLE D* TLE E* DN 200 S1 R13.*** DN 225 S1 R13.*** DN 300 S1 R13.*** DN 350 S1 R13.*** DN 375 S1 R13.*** LIND PLSTIC LINER IS RECOMMENDED TO E USED WITH LIND STEEL PLTE STNDRD MTERIL: HOT DIPPED GLVNISED MILD STEEL TO S/NZS 4680: : DRILLED TLE E / S 2129: : DRILLED TLE D / S 2129:2000. OTHER DRILLINGS VILLE ON REQUEST LIND S LINER TO SUIT PIPE mm DN 200 S1 R11.*** DN 225 S1 R11.*** DN 300 S1 R11.*** DN 350 S1 R11.*** DN 375 S1 R11.*** mm FOR USE IN CONJUNCTION WITH LIND STEEL PLTE STNDRD MTERIL: S WHITE SHEET 721: DRILLED TLE E / S 2129: : DRILLED TLE D / S 2129:2000 OTHER DRILLINGS VILLE ON REQUEST 12 DURFLO S PIPE & FITTINGS
15 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE CKING RING TLE D S 2129:2000 TO SUIT PIPE PCD NO OF HOLE DN mm mm mm mm HOLES mm DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R *DN 375 S1 R * WHEN CONNECTING S SYSTEMS TO OTHER SYSTEMS PLESE NOTE VRITION ETWEEN S SYSTEM DN DESIGNTION ND S 2129 DN DESIGNTION STNDRD MTERIL: HOT DIPPED GLVNISED MILD STEEL TO S/NZS 4680 :1999 VILLE IN STINLESS STEEL ON REQUEST: 422 OTHER DRILLINGS VILLE ON REQUEST DURFLO S PIPE & FITTINGS 13
16 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE CKING RING TLE E S 2129:2000 TO SUIT PIPE PCD NO OF HOLE DN mm mm mm mm HOLES mm DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R *DN 375 S1 R * WHEN CONNECTING S SYSTEMS TO OTHER SYSTEMS PLESE NOTE VRITION ETWEEN S SYSTEM DN DESIGNTION ND S 2129 DN DESIGNTION STNDRD MTERIL: HOT DIPPED GLVNISED MILD STEEL TO S/NZS 4680:1999. VILLE IN STINLESS STEEL ON REQUEST: 420 OTHER DRILLINGS VILLE ON REQUEST 14 DURFLO S PIPE & FITTINGS
17 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE CKING RING NSI150 TO SUIT PIPE PCD NO OF HOLE DN mm mm mm mm HOLES mm DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R DN 375 S1 R STNDRD MTERIL: HOT DIPPED GLVNISED MILD STEEL TO S/NZS 4680:1999. VILLE IN STINLESS STEEL ON REQUEST: 430 OTHER DRILLINGS VILLE ON REQUEST DURFLO S PIPE & FITTINGS 15
18 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE CKING RING JIS10K TO SUIT PIPE PCD NO OF HOLE DN mm mm mm mm HOLES mm DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R *DN 375 S1 R * WHEN CONNECTING S SYSTEMS TO OTHER SYSTEMS PLESE NOTE VRITION ETWEEN S SYSTEM DN DESIGNTION ND JIS 10K DN DESIGNTION STNDRD MTERIL: HOT DIPPED GLVNISED MILD STEEL TO S/NZS 4680:1999 VILLE IN STINLESS STEEL ON REQUEST: 445 OTHER DRILLINGS VILLE ON REQUEST 16 DURFLO S PIPE & FITTINGS
19 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE VLVE SUPPORT PLTE TO SUIT PIPE C D E F mm mm mm mm mm mm DN 15 S1 R03.*** DN 20 S1 R03.*** DN 25 S1 R03.*** DN 32 S1 R03.*** DN 40 S1 R03.*** DN 50 S1 R03.*** DN 65 S1 R03.*** DN 80 S1 R03.*** DN 100 S1 R03.*** DN 125 S1 R03.*** DN 150 S1 R03.*** DN 200 S1 R13.*** DN 225 S1 R13.*** DN 300 S1 R13.*** E D C F STNDRD MTERIL: HOT DIPPED GLVNISED MILD STEEL TO S/NZS : DRILLED TLE E / S 2129: : DRILLED TLE D / S 2129: : DRILLED TO NSI 150 OTHER DRILLINGS VILLE ON REQUEST VILLE IN STINLESS STEEL ON REQUEST. DURFLO S PIPE & FITTINGS 17
20 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE GSKET FULL FCE STYLE mm mm mm DN 15 S1 R04.*** DN 20 S1 R04.*** DN 25 S1 R04.*** DN 32 S1 R04.*** DN 40 S1 R04.*** DN 50 S1 R04.*** DN 80 S1 R04.*** DN 100 S1 R04.*** DN 150 S1 R04.*** DN 200 S1 R14.*** DN 225 S1 R14.*** DN 300 S1 R14.*** DN 350 S1 R14.*** DN 375 S1 R14.*** SEE NOTES ND DRILLING DETILS ON PGES 13, 14, 15, 16 STNDRD MTERIL: EPDM. OTHER MTERILS RE VILLE ON REQUEST 409: DRILLED TLE D* / S 2129: : DRILLED TLE E* / S 2129: : DRILLED TO NSI 150* OTHER DRILLINGS VILLE ON REQUEST 18 DURFLO S PIPE & FITTINGS
21 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE GSKET STU FLNGE STYLE EPDM mm mm mm DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DURFLO S PIPE & FITTINGS 19
22 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE ELOW 90º Z PN mm mm mm RTING DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R V DN 300 S1 R V DN 350 S1 R R DN 375 S1 R V Z ELOW DN 350 IS MNUFCTURED FROM ELOW DN 375 FITTED WITH DN DN 350 REDUCING USHES FOR DN 200 ND OVE, ELOWS WITH HIGHER PRESSURE RTINGS RE VILLE THEY RE MNUFCTURED FROM S LYERED WITH GLSS REINFORCED EPOXY ND RE DESIGNED ND MNUFCTURED IN CCORDNCE WITH DURFLO INTERNL QULITY ND MNUFCTURING PROCEDURES ND SPECIFICTIONS ND TYPE TESTED T 3.2 TIMES THE DESIGN PRESSURE 20 DURFLO S PIPE & FITTINGS
23 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE ELOW 45º Z Z PN mm mm mm RTING DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R V DN 225 S1 R V DN 300 S1 R V DN 350 S1 R R DN 375 S1 R V ELOW DN 350 IS MNUFCTURED FROM ELOW DN 375 FITTED WITH DN DN 350 REDUCING USHES FOR DN 200 ND OVE, ELOWS WITH HIGHER PRESSURE RTINGS RE VILLE THEY RE MNUFCTURED FROM S LYERED WITH GLSS REINFORCED EPOXY ND RE DESIGNED ND MNUFCTURED IN CCORDNCE WITH DURFLO INTERNL QULITY ND MNUFCTURING PROCEDURES ND SPECIFICTIONS ND TYPE TESTED T 3.2 TIMES THE DESIGN PRESSURE DURFLO S PIPE & FITTINGS 21
24 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE FUCET ELOW 90º C D Z PN SW SOCKET THREDED mm mm mm mm mm mm RTING DN 15 S1 ½" SP R DN 20 S1 ¾" SP R DN 25 S1 1" SP R DN 20 S1 ½" SP R D Z C COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
25 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE MOULDED END 90º C L PN mm mm mm mm mm RTING DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R C L COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 23
26 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE END 90º SHORT RDIUS R = 2.5D (SP-SP) PN mm minmm RTING DN 50 S1 PN 15 R DN 65 S1 PN 15 R DN 80 S1 PN 15 R DN 100 S1 PN 15 R DN 125 S1 PN 15 R DN 150 S1 PN 15 R DN 200 S1 PN 9 R DN 225 S1 PN 9 R DN 300 S1 PN 9 R DN 350 S1 PN 9 R DN 375 S1 PN 9 R R 90 = MINIMUM LEG LENGTH MNUFCTURING TOLERNCES PPLY OTHER NGLES RE VILLE UPON REQUEST THE FOLLOWING DDITIONL END PRESSURE RTINGS RE VILLE UPON REQUEST: LL S LL S DN 50 TO DN HIGHER PRESSURE RTED ENDS RE VILLE WITH GLSS REINFOCED EPOXY ND RE SUPPLIED COMPLETE WITH SOCKETS T OTH ENDS. THEY RE DESIGNED ND MNUFCTURED IN CCORDNCE WITH DURFLO INTERNL QULITY ND MNUFCTURING PROCEDURES ND SPECIFICTIONS ND TYPE TESTED T 3.2 TIMES THE DESIGN PRESSURE ENDS SUPPLIED PLIN ENDED, REQUIRE SOCKETS OR STU & CKING RING FOR JOINING 24 DURFLO S PIPE & FITTINGS
27 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE END 45º SHORT RDIUS R = 2.5D (SP-SP) R PN mm min. mm RTING DN 50 S1 PN 15 R DN 65 S1 PN 15 R DN 80 S1 PN 15 R DN 100 S1 PN 15 R DN 125 S1 PN 15 R DN 150 S1 PN 15 R DN 200 S1 PN 12 R DN 225 S1 PN 12 R DN 300 S1 PN 12 R DN 350 S1 PN 12 R DN 375 S1 PN 12 R = MINIMUM LEG LENGTH MNUFCTURING TOLERNCES PPLY OTHER NGLES RE VILLE UPON REQUEST THE FOLLOWING DDITIONL END PRESSURE RTINGS RE VILLE UPON REQUEST: PN PN PN 9 LRGER DIMETER ENDS RE SUPPLIED WITH GLSS REINFOCED EPOXY ND RE SUPPLIED COMPLETE WITH SOCKETS T OTH ENDS. THEY RE DESIGNED ND MNUFCTURED IN CCORDNCE WITH DURFLO INTERNL QULITY ND MNUFCTURING PROCEDURES ND SPECIFICTIONS ND TYPE TESTED T 3.2 TIMES THE DESIGN PRESSURE ENDS SUPPLIED PLIN ENDED, REQUIRE SOCKETS OR STU & CKING RING FOR JOINING DURFLO S PIPE & FITTINGS 25
28 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE END 90º LONG RDIUS R = 5D (SP-SP) PN mm min. mm RTING DN 50 S1 PN 15 R DN 65 S1 PN 15 R DN 80 S1 PN 15 R DN 100 S1 PN 15 R DN 125 S1 PN 15 R DN 150 S1 PN 15 R DN 200 S1 PN 12 R DN 225 S1 PN 12 R DN 300 S1 PN 12 R DN 350 S1 PN 12 R DN 375 S1 PN 12 R R = MINIMUM LEG LENGTH MNUFCTURING TOLERNCES PPLY OTHER NGLES ND PRESSURE RTINGS RE VILLE UPON REQUEST ENDS SUPPLIED PLIN ENDED, REQUIRE SOCKETS OR STU & CKING RING FOR JOINING 26 DURFLO S PIPE & FITTINGS
29 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE END 45º LONG RDIUS R = 5D (SP-SP) PN mm min. mm RTING DN 50 S1 PN 15 R DN 65 S1 PN 15 R DN 80 S1 PN 15 R DN 100 S1 PN 15 R DN 125 S1 PN 15 R DN 150 S1 PN 15 R DN 200 S1 PN 12 R DN 225 S1 PN 12 R DN 300 S1 PN 12 R DN 350 S1 PN 12 R DN 375 S1 PN 12 R R 45 = MINIMUM LEG LENGTH MNUFCTURING TOLERNCES PPLY OTHER NGLES ND PRESSURE RTINGS RE VILLE UPON REQUEST ENDS SUPPLIED PLIN ENDED, REQUIRE SOCKETS OR STU & CKING RING FOR JOINING. DURFLO S PIPE & FITTINGS 27
30 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE EQUL TEE (SO-SOxSO) L Z mm mm mm mm mm TYPE PN RTING DN 15 S1 R M 15 DN 20 S1 R M 15 DN 25 S1 R M 15 DN 32 S1 R M 15 DN 40 S1 R M 15 DN 50 S1 R M 15 DN 65 S1 R M 15 DN 80 S1 R M 15 DN 100 S1 R M 15 DN 125 S1 R F 15 DN 150 S1 R M 15 DN 200 S1 R V M 12 DN 225 S1 R V M 12 DN 300 S1 R V M 12 DN 350 S1 R F 6 L Z Z DN 375 S1 R V M 6 COMPLIES WITH S/NZS 3518 TEE DN 350 IS MNUFCTURED FROM TEE DN 375 FITTED WITH DN DN 350 REDUCING USHES FOR DN 200 ND OVE, TEES WITH HIGHER PRESSURE RTINGS RE VILLE. THEY RE MNUFCTURED FROM S LYERED WITH GLSS REINFORCED EPOXY ND RE DESIGNED ND MNUFCTURED IN CCORDNCE WITH DURFLO INTERNL QULITY ND MNUFCTURING PROCEDURES ND SPECIFICTIONS ND TYPE TESTED T 3.2 TIMES THE DESIGN PRESSURE 28 DURFLO S PIPE & FITTINGS
31 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE REDUCING TEE SPIGOT OFFTKE (SO-SOxSP) C L PN mm mm mm mm mm RTING DN 200 DN 150 R DN 225 DN 150 R DN 300 DN 200 R DN 350 DN 225 R DN 375 DN 225 R C L COMPLIES WITH S/NZS 3518 MXIMUM LLOWLE SPIGOT DIMETER IS SHOWN REDUCERS TO SMLLER DIMETER SPIGOTS RE VILLE UPON REQUEST DURFLO S PIPE & FITTINGS 29
32 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE REDUCING TEE SOCKET OFFTKE (SO-SOxSO) C 1 2 Z1 Z2 PN mm mm mm mm mm mm mm RTING DN 20 DN 15 R DN 25 DN 15 R DN 25 DN 20 R DN 40 DN 25 R DN 50 DN 25 R DN 50 DN 40 R C Z2 2 Z1 1 COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
33 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE TEE THREDED OFFTKE (SO-SOxTH) C D Z PN SW SOCKET THREDED mm mm mm mm mm mm RTING DN 15 S1 ½" SP R DN 20 S1 ½" SP R DN 20 S1 ¾" SP R DN 25 S1 ½" SP R DN 25 S1 1" SP R Z D C COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 31
34 C S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE Y PIECE 45º C Z1 Z2 Z3 mm mm mm mm mm mm DN 20 S1 R M 15 DN 25 S1 R M 15 DN 32 S1 R M 15 DN 40 S1 R M 15 DN 50 S1 R M 15 DN 80 S1 R F 6 DN 100 S1 R F 6 DN 150 S1 R F 6 TYPE* PN RTING MOULDED C Z2 Z3 Z1 FRICTED Z2 Z3 Z1 COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
35 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE SDDLE STRIPS D* degree mm DN 80 S1 R º 300 ½" DN 100 S1 R º 300 1" DN 125 S1 R º 300 1" DN 150 S1 R º 300 1¼" DN 200 S1 R º 300 1¼" DN 225 S1 R º 300 1½" DN 300 S1 R º 300 1½" DN 350 S1 R º 300 1½" DN 375 S1 R º 300 1½" D = MXIMUM OF THE THREDED TPPING SDDLE STRIP SUPPLIED WITH STINLESS STEEL STRPS DURFLO S PIPE & FITTINGS 33
36 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE TPPING SDDLES 1 2 C D L PN MIN OFFTKE mm mm mm mm mm mm mm RTING DN 80 S1 DN 50 S1 R DN 100 S1 DN 50 S1 R C L 1 D COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
37 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE REDUCING SOCKET 1 1 L L1 Z mm mm mm mm mm mm mm mm TYPE PN RTING DN 20 - DN 15 S1 R M 15 DN 25 - DN 15 S1 R M 15 DN 25 - DN 20 S1 R M 15 DN 32 - DN 25 S1 R M 15 DN 40 - DN 25 S1 R M 15 DN 40 - DN 32 S1 R M 15 DN 50 - DN 40 S1 R M 15 DN 65 - DN 50 S1 R F 15 DN 80 - DN 50 S1 R M 15 DN 80 - DN 65 S1 R F 15 DN DN 80 S1 R M 15 DN DN 100 S1 R F 9 MOULDED DN DN 100 S1 R M 15 DN DN 125 S1 R F 15 DN DN 150 S1 R F Z L1 L Z 1 DN DN 195 S1 R F 12 DN DN 200 S1 R F 12 DN DN 225 S1 R F 12 DN DN 300 S1 R F 9 DN DN 350 S1 R F 9 FRICTED 45 L1 L DURFLO S PIPE & FITTINGS 35
38 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE REDUCING USH Z PN mm mm mm mm RTING DN 20 - DN 15 S1 R DN 25 - DN 15 S1 R DN 25 - DN 20 S1 R DN 32 - DN 15 S1 R DN 32 - DN 20 S1 R DN 32 - DN 25 S1 R DN 40 - DN 15 S1 R DN 40 - DN 20 S1 R DN 40 - DN 25 S1 R DN 40 - DN 32 S1 R DN 50 - DN 25 S1 R DN 50 - DN 32 S1 R DN 50 - DN 40 S1 R DN 65 - DN 50 S1 R DN 80 - DN 20 S1 R DN 80 - DN 40 S1 R DN 80 - DN 50 S1 R DN 80 - DN 65 S1 R DN DN 50 S1 R DN DN 80 S1 R DN DN 100 S1 R DN DN 100 S1 R DN DN 125 S1 R DN DN 150 S1 R DN DN 200 S1 R DN DN 225 S1 R DN DN 300 S1 R DN DN 350 S1 R Z TYPE TYPE Z COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
39 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE FUCET SOCKET PLIN THREDED SOCKET C L C L OD Z PN SW SOCKET THRED SPIGOT mm mm mm mm mm mm mm RTING DN 15 S1 ½" SP DN 20 S1 R DN 20 S1 ¾" SP DN 25 S1 R DN 25 S1 1" SP DN 32 S1 R DN 32 S1 1¼" SP - R DN 40 S1 1½" SP DN 50 S1 R DN 50 S1 2" SP - R OD Z FUCET DPTOR FEMLE Z1 C C OD Z Z1 PN SW SPIGOT THRED SW SOCKET mm mm mm mm mm mm mm RTING DN 15 S1 ½" SP - R DN 20 S1 ¾" SP DN 15 S1 R DN 25 S1 1" SP DN 20 S1 R DN 32 S1 1¼" SP DN 25 S1 R DN 40 S1 1½" SP - R DN 50 S1 2" SP DN 40 S1 R OD Z COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 37
40 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE VLVE DPTOR PLIN THREDED NIPPLE C OD Z1 Z PN SW SPIGOT THRED SW SOCKET mm mm mm mm mm mm mm RTING DN 15 S1 ½" - R DN 20 S1 ¾" DN 15 S1 R DN 25 S1 1" DN 20 S1 R DN 32 S1 1¼" DN 25 S1 R DN 40 S1 1½" - R DN 50 S1 2" DN 40 S1 R C Z1 OD Z REDUCING VLVE DPTOR REDUCING PLIN THREDED NIPPLE C OD Z1 Z PN SW SPIGOT THRED SW SOCKET mm mm mm mm mm mm mm RTING DN 20 S1 ½" DN 15 S1 R DN 25 S1 ½" DN 20 S1 R DN 25 S1 ¾" DN 20 S1 R DN 32 S1 1" DN 25 S1 R DN 40 S1 1" - R DN 40 S1 1¼" - R DN 50 S1 1" DN 25 S1 R DN 50 S1 1½" DN 40 S1 R Z1 C OD Z COMPLIES WITH S/NZS DURFLO S PIPE & FITTINGS
41 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE VLVE SOCKET MLE DPTOR Z C Z PN SW SOCKET THRED mm mm mm mm mm RTING DN 15 S1 ½" SP R DN 20 S1 ¾" SP R DN 25 S1 1" SP R DN 32 S1 1¼" SP R DN 40 S1 1½" SP R DN 50 S1 2" SP R DN 80 S1 3" SP R DN 100 S1 4" SP R C COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 39
42 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE CP C mm mm mm mm DN 15 S1 R M 15 DN 20 S1 R M 15 DN 25 S1 R M 15 DN 32 S1 R M 15 DN 40 S1 R M 15 DN 50 S1 R M 15 DN 65 S1 R F* 12 DN 80 S1 R M 12 DN 100 S1 R M 12 DN 125 S1* R F* 12 DN 150 S1 R M 12 DN 200 S1 R F 9 DN 225 S1 R F 9 DN 300 S1 R F 9 TYPE PN RTING FRICTED C MOULDED C * CP DN 125 IS MNUFCTURED FROM CP DN 150 ND DN DN 125 REDUCING USH 40 DURFLO S PIPE & FITTINGS
43 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE THREDED PLUG THRED C PN mm mm mm RTING DN 15 S1 ½" SP R DN 20 S1 ¾" SP R DN 25 S1 1" SP R DN 32 S1 1¼" SP R DN 40 S1 1½" SP R DN 50 S1 2" SP R C COMPLIES WITH S/NZS 3518 DURFLO S PIPE & FITTINGS 41
44 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE SOCKET UNION Z PN mm mm mm mm RTING DN 15 S1 R K DN 20 S1 R K DN 25 S1 R K DN 32 S1 R K DN 40 S1 R K DN 50 S1 R K DN 80 S1 R K DN 100 S1 R K Z SELS MTERIL: EPDM COMPLIES WITH S DURFLO S PIPE & FITTINGS
45 t S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE SDDLE CLIP C D t mm mm mm mm mm mm DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 80 S1 R DN 100 S1 R D C = CLIP THICKNESS MTERIL: LCK POLYPROPYLENE DURFLO S PIPE & FITTINGS 43
46 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE PIPE CLIP C D d1 d2 d3 Z1 Z2 mm mm mm mm mm mm mm mm TYPE DN 15 S1 R DN 20 S1 R DN 25 S1 R DN 32 S1 R C DN 40 S1 R C DN 50 S1 R C DN 80 S1 R C DN 100 S1 R C DN 150 S1 R F d1 d1 d2 d1 d2 C D D C D d3 d3 d3 Z1 Z2 Z1 Z2 Z1 Z2 TYPE TYPE C TYPE F S UP TO DN 375 VILLE ON REQUEST MTERIL: LCK POLYPROPYLENE 44 DURFLO S PIPE & FITTINGS
47 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE RUER EXPNSION JOINT C D E PN mm mm mm RTING DN 32 S1 R DN 40 S1 R DN 50 S1 R DN 80 S1 R DN 100 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R DN 375 S1 R / C / D / E = NTURL LENGTH C = XIL COMPRESSION D = NGULR DEFLECTION E = XIL EXTENSION FLNGES SUPPLIED RE ZINC PLTED GLVNISED VILLE ON REQUEST DURFLO S PIPE & FITTINGS 45
48 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE NCHOR SLEEVE mm mm mm DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R DN 375 S1 R SLIT NCHOR FLNGE C D mm mm mm mm mm DN 50 S1 R DN 65 S1 R DN 80 S1 R DN 100 S1 R DN 125 S1 R DN 150 S1 R DN 200 S1 R DN 225 S1 R DN 300 S1 R DN 350 S1 R DN 375 S1 R SLIT IN TWO D C 46 DURFLO S PIPE & FITTINGS
49 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE LL CHECK VLVE SINGLE UNION Z PN mm mm mm RTING DN 15 S1 R01.***.015K DN 20 S1 R01.***.020K DN 25 S1 R01.***.025K DN 32 S1 R01.***.032K DN 40 S1 R01.***.040K DN 50 S1 R01.***.050K DN 80 S1 R01.***.080K *** EPDM SELS *** FPM SELS Z LL VLVE DOULE UNION D C D Z PN mm mm mm mm mm RTING DN 15 S1 R01.***.015K DN 20 S1 R01.***.020K DN 25 S1 R01.***.025K DN 32 S1 R01.***.032K DN 40 S1 R01.***.040K DN 50 S1 R01.***.050K DN 80 S1 R01.***.080K DN 100 S1 R01.***.100K *** EPDM SELS *** FPM SELS C Z DURFLO S PIPE & FITTINGS 47
50 S PIPES & FITTINGS FOR INDUSTRIL PPLICTIONS TOUGH, RESILIENT THERMOPLSTIC WITH HIGH IMPCT STRENGTH, GOOD CHEMICL RESISTNCE, NON TOXIC & TINT FREE SOLVENT CEMENT USGE* SOLVENT WELD JOINTS PER LITRE** DN 50 S1 135 DN 80 S1 45 DN 100 S1 35 DN 125 S1 20 DN 150 S1 20 DN 200 S1 10 DN 225 S1 4 DN 300 S1 4 DN 350 S1 3 DN 375 S1 2 DN 400 S1 1 DN 450 S1 1 DN 500 S1 0.5 DN 575 S1 0.5 DN 650 S1 0.3 DN 750 S1 0.3 S SOLVENT CEMENT CN litres 0.25 R R R MEK CLENER/PRIMER CN litres 0.25 R R R * THE USGE OF MEK IS PPROXIMTELY 50% THT OF S CEMENT ** SOCKET COUNTS S 2 JOINTS, TEE S 3 JOINTS, ETC. 48 DURFLO S PIPE & FITTINGS
51 DISCLIMER This document has been prepared by Viadux to assist qualified engineers and contractors in the selection of the Company s product, and is not intended to be an exhaustive statement on pipeline design, installation or technical matters. ny conclusions, formulae and the like contained in the manual represent best estimates only and may be based on assumptions which, while reasonable may not necessarily be correct for every installation. Successful installation depends on numerous factors outside the Company s control, including site preparation and installation workmanship. Users of this catalogue must check technical developments from research and field experience and rely on their knowledge, skill and judgement, particularly with reference to the qualities and suitability of the products and conditions surrounding each specific istallation. The Company disclaims all liability to any person who relies on the whole or any part of this manual and excludes all liability imposed by any statute or by the general law in respect of this manual whether statements and representation in this manual are made negligently or otherwise except to the extent it is prevented by law from so doing. The catalogue is not an offer to trade and shall not form any part of the trading terms in any transaction. Viadux trading terms contain specific provisions which limit the liability of Viadux Pty Ltd to the cost of replacing or repairing any defective product. DURFLO S PIPE & FITTINGS 49
52 PROJECT OFFICE SYDNEY P: F: E: CUSTOMER CENTRES TOWNSVILLE P: F: E: SOUTH EST QUEENSLND P: F: E: NEWCSTLE P: F: E: SYDNEY P: F: E: MELOURNE P: F: E: DELE P: F: E: PERTH P: F: E: DRWIN P: F: E: VUX PTY LTD PO OX 141 FIRFIELD, NEW SOUTH WLES 1860 USTRLI / VUX.COM.U / PHONE 1300VUX ll Viadux trademarks and logos are owned by Viadux Pty. Ltd. ll other brand or product manes are trademarks or registered marks of their respective owners. ecause we are continuously improving our products and services, Viadux reserves the right to change specifications without prior notice.
abs section guide application guide standards and approvals
abs Acrylonitrile - Butadiene - Styrene (ABS) is a rigid pressure piping system renowned for its high impact strength and durability which combine to give exceptional toughness. It is suitable for use
Solenoid Pilot Operated Directional Control Valve
efore using the product, plese check the guide pges t the front of this ctlog. http://www.dikinpmc.com/en/ Solenoid Pilot Operted Directionl Control Vlve Fetures hese models relize high-pressure lrge-flow-rte
Solenoid Pilot Operated Directional Control Valve
Contct Detils efore using the product, plese check the guide pges t the front of this ctlog. http://www.dikinpmc.com/en/ For ltest informtion, PDF ctlogs nd opertion mnuls Solenoid Pilot Operted Directionl
Wirewound Resistor, Industrial High Power, Vitreous Tubular, Adjustable, Low Values 0.12 to 560
Wirewound Resistor, Industrial High Power, Vitreous Tubular, djustable, Low Values to 560 FETURES High power rating: 16 W to 600 W at 25 C Heavy overloads 10 P n 15 s 1 % Low ohmic values 0.10 available
Brazed heat exchanger XB
Description The XB is rnge of copper rzed plte het exchngers for use in District Heting (DH) nd District Cooling (DC) pplictions, e.g. domestic hot wter production, district heting susttion to seprte the
AWWA Grooved Fittings
WW Grooved Produts WW Grooved Fittings MTERI SPECIFICTIONS Mteril - Dutile Iron per STM 53 Grde 5-45-12. Interior lining - Cement lined per NSI/WW C104/21.4 sizes 3 single thikness nd sizes 4-3 doule thikness
Series 250 Type and Type Pneumatic Control Valves Type 3251 Globe Valve
Series 250 Type 3251-1 nd Type 3251-7 Pneumtic Control Vlves Type 3251 Globe Vlve DIN version Appliction Control vlve for process engineering pplictions with high industril requirements Nominl size DN
Solenoid Pilot Operated Directional Control Valve
Contct Detils efore using the product, plese check the http://www.dikinpmc.com/en/ For ltest informtion, DF ctlogs nd opertion mnuls Solenoid ilot Operted Directionl Control Vlve Fetures hese models relize
Pipe Fittings & Steel Nipples
Pipe Fittings & Steel Nipples www.anvilintl.com NOVEMER 20 For the most current product/pricing information on nvil products, please visit our website at www.anvilintl.com UILDING CONNECTIONS THT LST For
Pipe Fittings & Steel Nipples
November 200 For the most current product/pricing information on nvil products, please visit our website at www.anvilintl.com. Pipe Fittings & Steel Nipples U I L D I N G C O N N E C T I O N S T H T L
VB-7000 Series. Selection Guide. Applications. Applicable Literature. Selection Guide Contents
V-7000 Series Selection Guide T V-7000 Series 1/2 to 2 Globe Vlves with Fort M400, M800, nd M1500 ctutors pplictions T Fort M400, M800, nd M1500 series liner ctutors mount directly 1 onto 1/2 to 2 V-7xxx
FINGER STRIPS. and other EMI shielding products. Characteristics
BERYLLIUM COPPER CONTCT FINGER STRIPS nd other EMI shielding products ppliction Due to their outstnding mteril nd electricl chrcteristics, eryllium copper fingers of different shpes nd dimensions re used
GATE VALVES ALV-1 FORGED STEEL NOMINAL PRESSURE NOMINAL SIZE MATERIALS CONNECTIONS. ANSI Class PN /4-2 DN 8-50.
FORGED STEEL GTE VLVES LV-1 NOMINL PRESSURE NSI Class 150-1500 PN 16-250 NOMINL 1/4-2 DN 8-50 MTERILS Carbon Steel Low lloy Steel Stainless Steel CONNECTIONS Socket Weld Butt Weld Threaded Flanged XELVLVES
Solenoid Pilot Operated Directional Control Valve
Contct Detils efore using the product, plese check the guide pges t the front of this ctlog. http://www.dikinpmc.com/en/ For ltest informtion, DF ctlogs nd opertion mnuls Solenoid ilot Operted Directionl
BRITISH STANDARD THREADS ALL MEASUREMENTS IN MM DEPTH OF THREADS IMPERIAL METRIC A P H B E
Fittings GLVNISED MLLELE IRON PIPE FITTINGS Specifications STNDRD ND IDENTIFITION: Standard for production and use EN 10242 : 1994. Fittings made of high quality blackheart malleable cast iron to STM -197,
RANGER FLANGE ADAPTORS
RANGER ADAPTORS RANGER products, in the form of wide range couplings and flange adaptors, are designed to join pipes of various outside diameters with the same or different nominal bore. Because of the
Georg Fischer Waga N.V. Your mechanical connection for plastic pipes restraint - non restraint d63 - d315. Products. Plast/Joint
Georg Fischer Wg N.V. Your mechnicl connection for plstic pipes restrint - non restrint - Proucts Plst/Joint Plst/Joint >> Your mechnicl restrint connection for plstic pipes >> With the increse use of
AWWA Grooved Fittings
WW Grooved Sumittl Form WW Grooved Fittings SUMITT INFORMTION PROECT NME: ENGINEER: CONTRCTOR: WW Grooved Fitting SPEC. SECTION: MEMER FETURES & DVNTGES Fittings supplied with rigid rdius grooves in ordne
ilent Silent Operation Proven Performance Cost Effective Silent Check Valves Check Valve
ulletin / Silent Operation Proven Performance Cost Effective ilent Check Silent Check s www.valmatic.com Certified Lead-Free NSF/NSI & 7 Certified Feature Highlights Threaded C F C Globe F C E Wafer F
2/2 4/4 Solenoid Directional Seat Valve, ISO Size 03
2/2 4/4 Solenoid Directionl Set Vlve, ISO Size 03 Q mx = 20 l/min, p mx = 315 r idirectionl set-vlve shut-off, direct cting, electriclly operted 1 Description he W2N / W2 series of 2/2 4/4 solenoid operted
The widest range to provide the optimum tailor made solutions to your fume and gas extraction needs.
FUME XTRACTION ARMS Improving your workspce Chemicl resistnt Antisttic Stndrd FX ARMS The widest rnge to provide the optimum tilor mde solutions to your fume nd gs extrction needs. Avilble in Stndrd, Antisttic
MATERIALS. Polypropylene
68509.verB_1_3.P1.fh 4/17/07 12:15 PM Page 1 THERMOPLASTIC INDUSTRIAL PIPING SYSTEMS Asahi/America thermoplastic piping systems are designed for tough industrial applications. With our partner Agru of
2/2 Solenoid Operated Seat Valve, ISO Size 03
2/2 Solenoid Operted Set Vlve, ISO Size 03 Q mx = 40 l/min (11 gpm), p mx = 315 r (4500 psi) Sndwich design, idirectionl lek-proof shutoff, direct cting, electriclly operted 1 Description 2 echnicl dt
4/2- and 4/3-way shut-off valve
Courtesy of CMA/Flodyne/Hydrdyne Motion Control Hydrulic Pneumtic Electricl Mechnicl (00) 426-540 www.cmfh.com 4/2- nd 4/3-wy shut-off vlve Type Z4WE Size 6 Component series 3X Mximum operting pressure
VALVE INSERTION WHEN YOU ARE UNDER PRESSURE TO INSTALL A VALVE IN AN OPERATING LINE VALVE INSERTION PAGE QV-2
www.romac.com 1-800-426-9341 WHEN YOU RE UNDER PRESSURE TO INSTLL VLVE IN N OPERTING LINE PGE QV-2 4", 6" or 8" installations in cast iron, ductile iron, /C and some classes of PVC pipe Uses modern resilient
SSAB Water mains PIPES AND FITTINGS
SSAB Wter mins PIPES AND FITTINGS Pipes nd fittings mnufctured y SSAB re used primrily with wter pipeline sizes DN 400-1200. The fittings re mde of steel pressure pipes (ex works delivery) nd cn e coted
Bespoke. Large Diameter Fittings to Suit any Pipe Specification
Bespoke Large Diameter Fittings to Suit any Specification P I P E C O N N E C T I O N S R E PA I R F L O W C O N T R O L P R O D U C T S Large Diameter Overview Robust, Reliable, Proven Solution for New
Advantages of Grooved Fittings
Grooved Fittings Advantages of Grooved Fittings Comparative Advantages Allows angular deflection-misalignment Expansion, contraction or, no need for expansion joint Reclaimable, no need for union Allows
THE SOLUTION YOU VE BEEN LOOKING FOR
LPP-D PVEG VLVES POMP LROX PVEG VLVES The Larox PVEG is a general purpose pinch valve. Compact by design, the reliable PVEG valves are well suited for a wide range of applications, which require resistance
FIBERGLASS ROUND CONTROL DAMPERS. Model K-RD INTRODUCTION M.K. PLASTICS PROVIDES FOUR DAMPER MODELS K-RD SUGGESTED SPECIFICATION
FIERGLSS ROUND CONTROL S INTRODUCTION The M.K. Plastics series K-RD are manufactured to meet the needs of the odor control and corrosive HVC industries by providing a corrosion-resistant FRP Damper that
industrial and economy pipe fittings PVC-U Solvent Cement WELD-ON REGULAR 719 Size Code Price 500ml tin
pvcu fittings mm sizes industrial and economy pipe fittings fittings mm sizes 68 Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings
Aluminium Floor Outlets - Trapped Outlets
Aluminium Floor Outlets - Trpped Outlets Verticl Trpped Outlet Components Drin Body Dimensions 260 Grte* Funnel Sel Trp Assemly Funnel Cup * Elevtion Throt Throt Sel DPM Clmp Ring with Weep Bung (shown
Valves & Flow Control Components Valves & Flow Control Components
Section 4 Valves & Flow ontrol omponents Valves & Flow ontrol omponents... 106 SJ-200 Low-Profile utterfly Valve... 107 SJ-300N utterfly Valve... 108 SJ-300F utterfly Valve (for Fire Protection)... 110
RPEL1-04. Functional Description HA /2014. Solenoid - Operated Directional Control Valves. Size 04 (D 02) 250 bar (3600 PSI) 30 l/min (8.
Solenoid - Operted Directionl Control Vlves RPEL-0 05/0 Size 0 (D 0) 50 r (600 PSI) 0 l/min (8.0 GPM) /-, /- nd /-wy directionl control vlves with solenoid control Solenoids cn e turned round their xis
HDPE PIPE SYSTEMS PRODUCT CATALOGUE.
HDPE PIPE SYSTEMS PRODUCT CATALOGUE www.acu-tech.com.au This is to certify that: The Trustee for The Morren Family Trust ABN 52 394 633 042 Trading As Acu-Tech Piping Systems 119 Kelvin Road Maddington
FE-1000 INSERTION TYPE AIRFLOW SENSING ELEMENT
Technical Data Sheet FE-1000 INSERTION TYPE IR SENSING ELEMENT DESCRIPTION The FE-1000 is an insertion type airflow sensing element designed for quick, easy installation through a small cutout in the existing
Harmer Roof Drainage The Cast Iron Range
Cst Iron Roof Outlets - Introduction Hrmer Roof Dringe The Cst Iron Rnge The high qulity Cst Iron Roof Outlet rnge, feturing medium sump nd lrge sump odies, two-wy outlets nd n extensive rnge of lodering
SUREFLOW FLANGED FITTINGS DUCTILE IRON PIPELINE SYSTEMS
80-750. MANUFACTURED TO AS/NZS 2280. FLANGE DIMENSIONS TO AS 4087 Ductile Iron fittings provide high strength and impact resistance Suitale for in ground or aove ground applications All fittings are supplied
UNIJOINT is a company of. UNIJOINT Eurocoup Flange Adaptors & Couplings
UNIJOINT is a company of UNIJOINT Eurocoup Flange Adaptors & Couplings UNIJOINT For Challenging Pipe Connections UNIJOINT, established in 1992 in the Netherlands, is a company with a vast experience in
Grooved Butterfly Valves
Grooved Butterfly Valves Design Rating: PN10, PN16 Design: UNE EN 539 Grooving dimensions: ANSI/ AWWA C 606 97 Face to face: MSS SP 67 Piping assembling: ANSI B3610, ISO 4200, DIN 2448, BS 1387, BS 3600
FIBERGLASS DAMPERS FOR ODOR CONTROL AND CORROSIVE HVAC SYSTEMS
FIERGLSS S FOR ODOR CONTROL ND CORROSIVE HVC SYSTEMS ELCO FIERGLSS S ELCO Fiberglass Dampers are manufactured to meet the needs of the odor control and corrosive HVC industries by providing a corrosion-resistant
Control stations and enclosures Control station enclosures : insulated, metal and flush mounting
Chrcteristics Control sttions nd enclosures Control sttion enclosures : insulted, metl nd Insulted enclosures XAP-A Mteril nd colour Glss-reinforced polyester, coloured grey throughout Approvls Specil
Control stations and enclosures
Chrcteristics Control sttions nd enclosures Control sttion enclosures: insulted, metl nd Insulted enclosures XAP-A Mteril nd colour Glss-reinforced polyester, coloured grey throughout Approvls Specil version:
standard and industrial pipe fittings
fittings mm sizes standard and industrial pipe fittings Photo: Chlor Generators Ltd Available in a wide range of mm sizes from 10mm to 500mm, and in a choice of pressure ratings from 6 bars to 16 bars,
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL
heavy duty industrial resilient seated butterfly valve GRW - Wafer body design GRL - Lugged body design FETURES GENERL PPLICTION Water, air, dry bulk conveying etc. These valves are for any service where
Product range MEGAlife
Product rnge Fx enquiries: +49 89 76909-11 sles@iwis.com MEGAlife MEGAlife mintennce free roller nd conveyor chins cn be pplied in ll res where post instlltion lubriction is not t ll or only prtly possible.
Series AIR LINE COMPRESSED AIR DISTRIBUTION SYSTEM
Series IR LINE COMPRESSED IR DISTRIUTION SYSTEM 26 IR LINE IR DISTRIUTION SYSTEM FETURES ND ENEFITS Installation ease: IR LINE installations can be carried out easily by the end-user, eliminating the need
PVC Push-Fit Soil & ABS Solvent Waste Systems
DC-DPG-PT SEPTEMER 2013 PVC Push-Fit Soil & S Solvent Waste Systems Trade Price ist Prices effective from 1st September 2013 ll dimensions in mm unless otherwise stated. 1 Polypipe We design, develop and
R E V I S I O N REV. DRAWN BY ECO No DESCRIPTION DATE APPROVED BILL OF MATERIALS
NOTES: UNLESS OTHERWISE SPECIFIED. CORNERS DRWN SHRP TO E R.005 MXIMUM. 2. EXTERIOR SURFCE TEXTURE TO E EQUIVLENT TO MT-007. TEXTURE ON ENCLOSURE WILL VRY FROM TIME TO TIME S THE TOOL WERS ND IT ECOMES
PVC PRESSURE PIPE SYSTEMS AS/NZS 4441, 4765, 1477 Potable water, non-potable water pressure applications
PVC PRESSURE PIPE SYSTEMS AS/NZS 4441, 4765, 1477 Potable water, non-potable water pressure applications JAN 2017 1 CONTENTS MATERIAL & DESIGN 3 PVC-O PRESSURE PIPE SERIES 2 5 PVC-M PRESSURE PIPE SERIES
Quality HSS (EW 9 Co 10 - cobalt 10%). Ø x l mm 16 x x x x x
Engrver's points Tool holder its Cutting-Off nd Grooving Tools 1812-1816 Engrver's Points With rough-ground profile. For use on tempered nd chrome-nickel steel. For engrving lettering, profiling for contours,
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL
KEYSTONE SERIES GR RESILIENT SETED BUTTERFLY VLVES GRW/GRL heavy duty industrial resilient seated butterfly valve GRW - Wafer body design GRL - Lugged body design FETURES GENERL PPLICTION Water, air, dry
SEE VICTAULIC PUBLICATION FOR DETAILS
dapters SEE VICTULIC PULICTION 10.01 FOR DETILS Style 741 Style 741 adapter is designed for directly incorporating flanged components with NSI CL. 125 or CL. 150/PN10 and PN16 or ustralian Standard Table
pvc-u section guide application guide standards and approvals
pvc-u Unplasticised Polyvinyl Chloride (PVC-U) is the most widely used of all plastics used for pipe installations. It is rigid, versatile, and is suitable for both above or below ground installations.
SOLENOID VALVES / DIRECTIONAL CONTROL VALVES
LOW-OWE ONSUMTION ILOT-OETED DIETIONL ONTOL VLVE * SIZE 04/0/10 This is n ssemly of solenoid vlve nd directionl control vlve to operte the directionl control vlve (min vlve) y mens of the pilot pressure
3-Way Ball Valve Assemblies Using TAC DuraDrive Actuators
3-Wy Bll Vlve Assemblies Using TAC DurDrive Actutors Note: All vlve sizes ANSI Clss IV (0.01% of C v ) shut off, piped coil-side outlet to A. Tble-5 Selection Chrt3-Wy Mixing Bll Vlve Assemblies with TAC
EURATECH INDUSTRIES SDN BHD ( M) Quality Without Compromise since 1987 COMPANY PROFILE
EURATECH INDUSTRIES SDN BHD (1139734-M) Quality Without Compromise since 1987 COMPANY PROFILE Lot 1478, Nilai Industrial Estate II, 71800 Nilai, Negeri Sembilan, Malaysia Website: www.euratech.com.my Company
Pipes and Fittings Imperial and Metric Systems
Pipes and Fittings Imperial and Metric Systems Complete system solutions t the forefront of development and manufacture of thermoplastic pipework for over half a century, Durapipe pipe systems are widely
Solenoid Operated Proportional Directional Control Valve (with Pressure Compensation, Multiple Valve Series)
Solenoid Operted Proportionl Directionl Control Vlve (with Pressure Compenstion, Multiple Vlve Series) Hydrulic circuit (Exmple) v Fetures hese stcking type control vlves show pressure compensted type
Cast Stainless Steel Butt-Weld Outlet Connection Data
180 Stainless Steel Cast Stainless Steel utt-weld Outlet Connection Data Josam cast stainless steel drains and cleanouts are regularly furnished with Schedule 40S butt-weld outlet connections. utt-weld
Large. Bespoke. Diameter. Fittings to Suit any Pipe Specification
Bespoke Large Fittings to Suit any Specification pipe ONNEIONS, repair & flow control products for the utilities industry Large Overview Robust, Reliable, Proven Solution for New Lay s ustomer Design Liaison
M J G O.D. B.C. A B I.D. C O.D. A B C I.D. B.C.
DI S TR Utility Pipe ittings and ccessories MJ ccessories NSI/WW 111/21.11 GLNDS, GSKETS, OLTS & NUTS GENERL SPEIITION MTERIL: PRESSURE: TESTING: DIMENSIONS: WEIGHTS: OTING: Ductile Iron per STM 536 350
TEL: Version: KW2
WWW.KLAMBON.COM 1 Page Klambon Water is a wholly owned subsidiary of West Rand Engineering (WRE), we are suppliers of valves, fittings and related products to all industries and our service extends to
4/2- and 4/3-directional spool valve solenoid-operated, direct-acting 4WE 6
4/2- nd 4/3-directionl spool vlve solenoid-operted, direct-cting 4WE 6 DESCRIION HYDC 4/2- nd 4/3- directionl spool vlves of the 4WE 6 series re directionl vlves for oil hydrulic systems which re used
Wirewound Resistors, Industrial Power, Vitreous Coated, Adjustable Tubular
Wirewound Resistors, Industrial Power, Vitreous oated, djustable Tubular FETURES High temperature vitreous coating omplete welded construction Tight tolerance of 5 % for values above 1 Excellent stability
HEATING BLANKETS FOR GENERAL COMPOSITE REPAIR
Innovtion in Technology for Aircrft Mintennce Equipment, Airline Support through Engineering & Trining Advnced Composite & Metllic Structures Cge Code - NATO Code : F7856 - Eur VAT- ID: FR90 328961073
2/2 Solenoid Operated Seat Valve, ISO Size 03
2/2 Solenoid Operted Set Vlve, ISO Size 03 Q mx = 20 l/min (5.3 gpm), p mx = 315 r (4500 psi) Sndwich design, idirectionl lek-proof shutoff, direct cting, with EX-sfty sol. coil Vlve: With crtridge vlve,
Titan Check Valves. Call. Fax. . Visit. Titan Flow Control. Your Pipeline to the Future
Your Pipeline to the Future TITAN 290 Corporate Drive Lumberton, NC 28358 Titan Check Valves, Inc. is a high quality manufacturer of check valves. With a dedication to great customer service, cutting edge
ABS Pipe metric system Plain PN10
S Pipe metric system Plain PN10 t (mean) Da (min) Size Thickness Weight Length ode t Da mm kg/m m 16 1.5 0.07 3 11 565 305 20 1.6 0.10 3 11 565 306 25 1.9 0.14 3 11 565 307 35 2.1 0.21 3 11 565 308 16
Copper-Nickel Alloys for Seawater Piping Systems (CuNi 90/10 and CuNi 70/30)
Shipbuilding OSNA -10 and OSNA -30 Copper-Nickel Alloys for Seawater Piping Systems (CuNi 90/10 and CuNi 70/30) KME Germany GmbH & Co. KG Shipbuilding - OSNA -10 and OSNA -30 [EN] Content KME - The Company
4/3-4/2 Directional valve elements L8_81 (ED4-P1) with or without LS connections. RE Edition: Replaces:
4/ - 4/ Directionl vlve elements L8_81 with proportionl (ED4-1) control nd with or without LS connections L8_81 (ED4-1) RE 181-1 Edition: 9.18 Replces: 7.1.17 Size Series Mximum operting pressure r (4
STK Series. Specifications. Stroke length (mm) High rigid cylinder Double acting/chamfered round rod end. Bore size: 20, 32, 40, 50 mm.
High rigid cylinder Doule cting/chmfered round rod end STK Series :, 32, 40, 50 mm JIS symol Doule cting CAD DATA AVAILABLE. Specifictions STK mm di. Actution Working fluid Mx. working pressure MP Doule
Draincoil. Features & Benefits. Draincoil corrugated drainage pipe is of a consistent high quality and comes in a broad range of sizes and grades.
Draincoil corrugated drainage pipe is of a consistent high quality and comes in a broad range of sizes and grades. It is available slotted or unslotted, with or without filter sock. There is a full range
Road Tunnel Fire Protection. with Alvenius Piping Systems
Road Tunnel Fire Protection with Alvenius Piping Systems EN 2 Alvenius piping systems where top safety is paramount Alvenius supplies reliable and safe steel piping for fire protection in road tunnels.
SHEET 1 OF 6
REVISIONS REV DESCRIPTION CHG.NO. PP'D DTE SENSOR WELD NECK MOUNTING FLNGE & WELD FTG. (FCTORY WELDED) VILBLE IN SME B16.5 RF & RTJ, ND EN 1092-1 RF. REFER TO TBLE 1 ON SHEET 2 OR FOR S ND DIMENSIONS NEW
GUARDIAN VERTICAL MOUNTING
GUARDIAN VERTICAL MOUNTING L120 GUARDIAN INDUSTRIAL & ATEX Exi VERTICAL REED LEVEL SWITCH This rnge of mgnet operted reed switches re equipped with hermeticlly seled reed contcts. The flot is fitted with
Free Machining Austenitic Ferritic + Martensitic Pure Titanium Titanium Alloys Stainless Steels Stainless Steels <950N/mm 2
& - Tps For Stinless Steels These top qulity Tps re mde in Switzerlnd, by DC-Swiss, one of the leding Tp Mnufcturers in Europe. All the Tps re mde of - (Powder Metl). This mteril hs proven to be the best
GACHOT TYPE V16 BALL VALVES CARBON STEEL / FULL BORE / DN 8 TO DN 150
CRBON STEEL / FULL BORE / DN 8 TO DN 150 Carbon steel, forged body full bore ball valve designed to international and European standards FETURES PPLICTIONS Saturated steam. mmonia, natural gas, propane
Section 18 Butterfly Valves
Section 18 Butterfly Valves Edition 2 261 [18] BUTTERFLY VALVES Butterfly Valves Resilient seat Butterfly Valves are used in a wide range of Industries including HVAC, Gas, Petrochemical, Pulp & Paper,
True Fit Tank Fittings
True Fit Tank Fittings SECTION NINE Level Alert Indicator TECHNICAL SPECIFICATIONS Female Tank Fitting Sanbra Fyffe Email: Ltd sales@herron.ie Email: sales@sanbra.ie Phone: +353 (0)71 91 33100 True Fit
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL (ISO)
heavy duty industrial resilient seated butterfly valve FETURES GENERL PPLICTION Water, air, dry bulk conveying etc. These valves are for any service where a drop-tight shut-off with maximum flow area is
ATLANTIC PLASTICS is a company of. UPE Multi Diameter Wide tolerance Couplings and Flange Adaptors
ATLANTIC PLASTICS is a company of UPE Multi Diameter Wide tolerance Couplings and Flange Adaptors The UPE MultiDiameter range of wide tolerance couplings and flange adaptors can be used for almost any
CLASS 400 FORGED BRASS BALL VALVE
CLASS 400 FORGED BRASS BALL VALVE FIG. 214 Screwed body cap, PTFE seats, Blowout-proof stem. Screwed ends to BS 21. Nickel plated body. Chrome plated ball. UNI-FLO NYLON BALL VALVES FIG. 214NS/NB Features:
BIMETAL-POINTER-THERMOMETER
BIMETA-POINTER-THERMOMETER Chemicl version cc. EN 30 byonet cse IP 6 With or without filling Suitble for chemicl nd petrochemicl industry, food, pulp nd pper industry nd for mchine nd pprtus contruction.
KEYSTONE SERIES GR RESILIENT SEATED BUTTERFLY VALVES GRW/GRL (ISO)
heavy duty industrial resilient seated butterfly valve FETURES GENERL PPLICTION Water, air, dry bulk conveying etc. These valves are for any service where a drop-tight shut-off with maximum flow area is
POWER COMBICON Plugs and Headers PC 6/ for Currents up to 41 A, mm Pitch
POWER COMBICON Plugs nd Heders PC 6/ for Currents up to 41 A, The PC 6 plug connector fetures highly conductive metl lloys to offer current crrying cpcity of 41 A t rted voltge of 1000 V. A double steel
Maximum leakage rate is less than half of the AWWA allowable Can be adapted to any channel Low-maintenance gates ***
Maximum leakage rate is less than half of the WW allowable Can be adapted to any channel Low-maintenance gates *** The Fontaine gate is designed to control water flows in channels. It is the same construction
The Number One Choice of Line Stopping Contractors
JCM 0 Line Stop Fittings Take a Look!!! JCM 0 FAMILY OF LINE STOP FITTINGS HAS EPANDED New Plug Option - New Numbering System Whatever your application needs, JCM has it! JCM Industries offers the largest
Pipes and Fittings Imperial and Metric Systems
Pipes and Fittings Imperial and Metric Systems PRIL 2007 Complete system solutions for industrial applications t the forefront of development and manufacture of thermoplastic pipework for over half a century,
TITAN DIFFERENTIAL PRESSURE DPF266 ATEX/IECEx Exd, Exia & INDUSTRIAL DIFFERENTIAL PRESSURE, SWITCH
TITAN DIFFERENTIAL PRESSURE DPF266 ATEX/IECEx Exd, Exi & INDUSTRIAL DIFFERENTIAL PRESSURE, SWITCH This rnge hs been used to monitor very smll chnges in vcuums nd hs been specified extensively for offshore
Plastic Pressure Systems Plastic Pressure Systems
Uniclass L71161:P71 CI/SfB TPL10-IND In6 February 2016 Plastic Pressure Systems Plastic Pressure Systems Plastic Pressure Systems TPL10-IND Trade List Polypipe Terrain New Hythe Business Park Trade List
AquaGrip. Unique. Couplings & Flange Adaptors. For Polyethylene Pipe Connections
Unique AquaGrip Couplings & Flange Adaptors For Polyethylene Pipe Connections PIPE CONNECTIONS, REPAIR & FLOW CONTROL PRODUCTS FOR THE UTILITIES INDUSTRY AquaGrip Overview A High Performance Polyethylene
Dismantling. Joint Range. Flexible PIONEERS IN PIPE SOLUTIONS. Fully Restrained Double Flanged Fitting
Flexible Dismantling Joint Range Fully Restrained Double d Fitting PIONEERS IN PIPE SOLUTIONS Dismantling Joint Overview Developed for Complete Versatility The Dismantling Joint range was developed to
08.08 Vic-Check Valves
The check valves are a product of computer-assisted innovative engineering with quality features including a new hydrodynamically efficient profile. The Vic-Check valve utilizes a spring-assisted, single-disc
Section 12 Contents. Product Reference Numbers and Ordering Information 12.10
Section 12 Contents DESCRIPTION Product Reference Numbers and Ordering Information PGE NUMER 12.10 Technical Details Head Shapes vailable Finishes vailable Camlock Fixing Methods Explaining Keying Details
631 ALLOWANES AND TOLERANCES
631 ALLOWANES AND TOLERANCES ANSI Fits. Tbles 3 through 9 inclusive show series of stndrd types nd clsses of fits on unilterl hole bsis, such tht the fit produced by mting prts in ny one clss will produce
2/2, 3/2 and 4/2 directional seat valve with mechanical, manual or fluidic operation
/, / nd / directionl set vlve with mechnicl, mnul or fluidic opertion RE 0/10.06 /1 ype M-.S.. Sizes 6 nd 10 Component series X Mximum operting pressure 0/ r Mximum flow 0 l/min H701+70+70 le of contents
Section 3. Stainless Steel Series. Shurjoint Stainless Steel Piping Series Grooved Mechanical Couplings. Cast Grooved Fittings.
Section 3 Stainless Steel Series Shurjoint Stainless Steel Piping Series... 84 Grooved Mechanical ouplings SS-5 Rigid oupling... 85 SS-7 Rigid oupling... 86 SS-7X Rigid oupling... 87 SS-8 Flexible oupling...
THOMAS. Unifit Premier Series. Couplings & Flange Adaptors Non Restrained Products PIPE PRODUCTS
THOMAS Couplings & Flange Adaptors Non Restrained Products PIPE PRODUCTS Unifit Premier Series Universal Pipe Couplings and Flange Adaptors for all Rigid Pipe J1 Unifit Premier Series Application Locally
Applicable Tubing. Tubing material Tubing outside O.D. Series KQ2 Series KQ
tuing dimeter: Metric Size : M, R, Rc KQ2/White ody Tuing Tuing mteril Tuing outside O.D. Nylon, Soft Nylon, Polyurethne ø, ø, ø, ø, ø, ø, ø1 Color Series Series KQ2 Series KQ Body White Blck Relese utton