R QUA. Y Your Global Force In Air Power C O M PA N

Transcription

1 New Vane/M Cat 1// : pm Page TE R QU OY LL Y Your Global Force In ir Power LI C O M P N D'S RE IS TY G P N E U M T I C V N E M O T O R S ISO 91

2 GLOBE IR POWER Vane ir Motors TEX Ex II--GDc-T CONTENTS PGE DVNTGES TYPICL CONSTRUCTION/DESIGN MOTOR SELECTION V1. HP REVERSIBLE V 1.1 HP REVERSIBLE V. HP REVERSIBLE V. HP REVERSIBLE 1 V 7. HP REVERSIBLE 1 V1 1. HP REVERSIBLE 1 Vane air motors offer a unique form of drive and incorporate advantages not found in other prime movers. These include: Inexpensive variable speed control when compared with electric motors Intrinsically safe in hazardous environments (e.g. mines, petro-chemical etc.) Can be stalled indefinitely under load without harm Instantly reversible Resistant to dirty, damp conditions Rugged design Suitable for use with natural gas Variety of mountings which include: Foot Face Nema C I.S.O. D flanges

3 DESIGN FETURES (Reversible) No pins or springs. The Globe blade ejection system consists of an ejection ring which maintains positive blade contact with the motor body. Vane motors are most suitable for light duties and higher speed operations and can be supplied direct coupled to gearboxes. variety of operating conditions can be achieved by utilization of pressure regulators and flow control valves. Oil-less Motors - certain models suitable for oil-less operations Other gases can also be used. Please consult our pplications Engineering department. SHFT/ROTOR SSEMBLY (REVERSIBLE) VNE LOCTION BERING END PLTE COVER PLTE -RING SHFT/ROTOR SSEMBLY (UNI-ROTTION) BODY BODY GSKET OIL SEL CIRCLIP SINGLE BERING FRONT PLTE DOWEL PIN BODY GSKET TYPICL CONSTRUCTION REVERSIBLE ND UNI-ROTTION MODELS

4 TYPICL SELECTION (EXMPLE BSED ON V) TORQUE (in. lbs.) 1 1 GRPH 1 TORQUE - SPEED 1 9 PSI 7 PSI PSI TORQUE (in. lbs.) 1 1 GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE Bar PRESSURE P.S.I. HORSE POWER GRPH POWER - SPEED PSI 7 PSI PSI Bar POWER kw IR CONSUMPTION cu. ft/min. free air GRPH CONSUMPTION - SPEED PSI 7 PSI PSI Bar litres/sec. free air MOTOR SELECTION Motor performance can be derived from the above graphs as in the examples shown. Where motors are not required to start under load, such as fan drives, selection may be made using either Graph 1 or Graph using the required running torque or power only. For applications where the motor starts under load, such as hoists, winches or track drives, the starting torque in Graph must also be considered. 1. Running torque example: V at psi gives 19 lbf.ins. torque at rpm.. Starting torque example: V at psi gives 1 lbf.ins.. Output power example: V at psi gives. hp at rpm.. ir consumption example: V at psi and rpm requires cu.ft./min. free air.

5 DIMENSIONS V1 NOTE: WITH INLET T PORT, SHFT ROTTION IS CLOCKWISE LOOKING ON SHFT. FOR OPPOSITE ROTTION REVERSE PORTS. PERFORMNCE V1 -. HP/. kw REVERSIBLE TORQUE (inch lbs.) 1 1 GRPH 1 TORQUE - SPEED 1 9 PSI 7 PSI PS BR BR BR TORQUE (inch lbs.) 1 1 GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE PRESSURE P.S.I.. HORSE POWER GRPH POWER - SPEED PSI PSI PSI BR BR BR 1. 1 POWER (WTTS) ttitude: The motor can be operated in all positions. irline filtration and lubrication: Use micron filtration or better. Choose a lubricator suitable for the flow required. Prior to start up, inject oil into the inlet port. Lubricator drop rate: - drops per minute continuous operation. 9-1 drops per minute intermittent operation. IR CONSUMPTION cu.ft/min. free air 1 1 GRPH CONSUMPTION - SPEED 1 9 PSI 7 PSI. PSI BR BR BR Polar Moment of Inertia:.1 lb.ins ( g.cm). Maximum overhung force on shaft: lbf (1N) xial loads should be kept to a minimum. Consult your Globe Distributor. Maximum temperatures: - to +17 Farenheit. (- to + C ) Muffler supplied with motor. litres/sec. free air

6 MOUNTING SPIGOT MOUNTING SPIGOT DIMENSIONS V MODEL VC Nema C configuration Ø 1.7 (.") Ø 1. (.") Holes - /" - 1-UNC Equi-spaced on 19. (.7") P.C.D. Ø 11.7 (.99") Ø 11. (.9") (.") (."). (1.7") Ø 7 (1.") Ø 1 (.") (.1") Ports/" N.P.T. 1. (."). (.") Key.7 (.1") SQ. X. (1.") LG (.1") (1.97") 1 (") Weight: 9.7 lb (. Kg) MODEL VJ Foot Mounting configuration.(1"). (1.7") 7 (.") 9.(1.1") Ø7(1.") 1(") (.1") Ports /" N.P.T. 1. (.") 9(.") Ø1.7 (.") Ø1.7 (.99") 11..F (.") 1(.") 1(.9") (.9") (1.") MOUNTING HOLES Ø7(.") 7(.").(.") Weight: 7.lb (.kg) MODEL VX Face Mounting configuration 1.97 (.1") Holes 1/" - UNC x 1 (.7") Deep on. (.") P.C.D. Ø1.7 (.") Ø1.7 (.99") MOUNTING SPIGOT Ø. (1.79") Ø. (1.77") 11..F (."). (1.7"). (1") 7(.") 9.(1.1") O7(1.") 1(.") 1(") (.1") (1.97") Ports /" N.P.T. 1. (."). (.") Weight: 7.lb.kg MODEL VSC D71 configuration Ø 1.1 (.1") Ø 1.1 (.1") Ø 1 (.") Ø 11. (.7") Ø 19.9 (.") KEY (.197") SQURE X (.7") LONG ROUNDED ENDS (1.1") (."). (.1"). (1.9") 1(.1") (.1") Ø 7 (1.") Ports G /". (.") 1(.9") 1. (.99") 1.7 (.") Holes Ø 9 (.") Equi-spaced on 1 (.11") P.C.D. 9 (.") TPPED HOLE IN SHFT. M X 1 (.9") DEEP. (1.") (1.") (1.") HOLES M X 1 (.") Deep (1.97") Ø9 (.7") Weight: 9.7 lb (. Kg) NOTE: With mains air at shaft rotation is clockwise. Reverse port connections for opposite rotation. Muffler supplied with motor.

7 PERFORMNCE V 1.1 HP/.kW REVERSIBLE TORQUE (inch lbs.) 1 1 GRPH 1 TORQUE - SPEED 1 9 PSI 7 PSI PSI TORQUE (inch lbs.) 1 1 GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE Bar PRESSURE P.S.I. HORSE POWER GRPH POWER - SPEED PSI PSI PSI Bar POWER kw IR CONSUMPTION cu. ft/min. free air GRPH CONSUMPTION - SPEED 1 9 PSI 7 PSI Bar PSI litres/sec. free air ttitude: The motor can be operated in all positions. irline filtration and lubrication: Use micron filtration or better. Choose a lubricator suitable for the flow required. Prior to start up, inject oil into the inlet port. Lubricator drop rate: - drops per minute continuous operation. 9-1 drops per minute intermittent operation. Polar Moment of Inertia:.7 lb.ins (.19 g.m). Maximum overhung force on shaft: 9 lbf (N) In certain circumstances this may be extended. Consult your Globe Distributor. xial loads should be kept to a minimum. Maximum temperatures: - to +17 Farenheit. (- to + C ) 7

8 MOUNTING SPIGOT MOUNTING SPIGOT DIMENSIONS V MODEL VC Nema C configuration Ø 1.7 (.") Ø 1. (.") Holes - /" - 1-UNC Equi-spaced on 19. (.7") P.C.D. Ø 11.7 (.99") Ø 11. (.9") 1 (.") (.") (.9") Ø (1.") O 1 (.") (.1") Ports 1/" N.P.T.. (.7") 9. (1.9") Key.7 (.1") SQ.. (1.") LG (.1") (1.97") O 9 (.") Weight: 17. lb (. Kg) MODEL VJ Foot Mounting configuration 1 Ø1.7 (.") Ø1.7 (.99"). (1.7") 9 (.") (1.") Ø (1.") 9 (.") (.1") Ports 1/" N.P.T. 9. (1.9").97 (.1") KEY.1 (.1") SQ 19 (.7") LONG 9 (.") 9 (.") 1 (.") (1.") (.9") (1.") MOUNTING HOLES Ø7 (9.") 7 (.") Weight:.lb (.kg) MODEL VX Face Mounting configuration 1 Ø1.7 (.") Ø1.7 (.99").97 (.1") HOLES, 1/"- UNC x 1 (.7") Deep Spaced on. (.") P.C.D. MOUNTING SPIGOT Ø. (1.79") Ø. (1.77") KEY.1(.1") SQ 19 (.7") LONG. (1.7") 1 (.") 9 (.") (1.") Ø (1.") 9(.") (.1") Ports 1/" N.P.T. (1.97") 9. (1.9"). (.7") Weight:.lb (.kg) MODEL VSC D71 configuration Ø 1.1 (.1") Ø 1.1 (.1") Ø 1 (.") Ø 11. (.7") Ø 19.9 (.") KEY (.197") SQURE X (.7") LONG ROUNDED ENDS. (1.1") 1(."). (.1") 1. (.") (.9") (.1") Ø (1.") Ports G 1/". (.7") 1 (.") 1. (.99") 1.7 (.") HOLES 9 (.") EQUII-SPCED ON 1 (.11") P.C.D. 9 (.") 9. (1.") TPPED HOLE IN SHFT. M X 1 (.9") DEEP. (1.7"). (1.1") HOLES M X 1 (.7") DEEP (1.97") Ø 9(.7") Weight: 17. lbs.. ( Kg.) NOTE: With mains air at shaft rotation is clockwise. Reverse port connections for opposite rotation. Muffler supplied with motor.

9 PERFORMNCE V. HP/.1 kw REVERSIBLE. GRPH 1 TORQUE - SPEED 1 9 PSI.. GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar. TORQUE lbs ft.) PSI PSI Bar TORQUE (lbs ft.) MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE PRESSURE P.S.I. HORSE POWER GRPH POWER - SPEED 1 9 PSI 7 PSI PSI Bar POWER kw IR CONSUMPTION cu. ft/min. free air GRPH CONSUMPTION - SPEED PSI 7 PSI PSI Bar 1 1 litres/sec. free air ttitude: The motor can be operated in all positions. irline filtration and lubrication: Use micron filtration or better. Choose a lubricator suitable for the flow required. Prior to start up, inject oil into the inlet port. Lubricator drop rate: - drops per minute continuous operation. 9-1 drops per minute intermittent operation. Polar Moment of Inertia:.77 lb.ins (. g.m). Maximum overhung force on shaft: lbf (17N) In certain circumstances this may be extended. Consult your Globe Distributor. xial loads should be kept down to a minimum. Maximum temperatures: - to +17 Farenheit. (- to + C ) 9

10 DIMENSIONS V MODEL VC Nema C Configuration Ø1.7(.") Ø1.(.") Ø1(.") HOLES, /"-1 UNC EQUISPCED ON 19. (.7") P.C.D. MOUNTING SPIGOT Ø (.") KEY.7(.1") SQ.(1.") LG. (1.1") (.1") 1(.") (.") (.") Ø11.7(.99") Ø11.(.9") 1 (.9") Ø1 (1.") (.") PORTS /" N.P.T. (.") Ø1(.1") 7.(.") 1(.") Weight: lb (1kg) MODEL VJ Foot Mounting Configuration 9 (.1") RD. 9. (1.9") 1 (.1") (.") Ø 1 (1.") Ø1(.1") (.") PORTS /" N.P.T. Ø 1.7 (.") Ø 1. (.") (.7") KEY.7 (.1") SQ. (1.") LG.9 (.") 1. (.9") 17 (.") (.") 1 (.7"). (.") 9.. (1.") (1.7") holes Ø9 11/" 1 (.") Weight: 17lb (7.kg) MODEL VX Face Mounting Configuration Ø 1.7 (.") Ø 1. (.") (.7") 9 (.1") RD. HOLES /1" - 1 UNC X (/") DEEP EQUISPCED ON 11. (.") P.C.D. Ø 7.1 (.") Ø 7.1 (.") MOUNTING SPIGOT KEY.7 (1.1") SQ. (1.") LG (.") 1 (.7") 9. (1.9") 1 (.1") (.") Ø 1 (1.") Ø1(.1") (.") (.") PORTS /" N.P.T. 7. (.") 1(.") Weight: 17lb (7.kg) MODEL VSC D Configuration Ø19.9(.7") Ø1.99(.779") Ø (7.7") Ø 1. (.11") Ø (.1") MOUNTING SPIGOT KEY (.") SQURE X (1.1") LONG ROUNDED T ONE END (1.7"). (.1") 1(.9") 7 (.7") HOLES M X 9(.") DEEP (1.9") (.9") PORTS G/" Ø1 (1.1") 7. (.") 1 (.7") 1.(.") 1.7(.7") HOLES Ø1(.7") EQUI-SPCED ON 1(.9") P.C.D. TPPED HOLE IN SHFT M X 1 (.9") DEEP. 1 (.9"). (.9") (.") (1.11") (.") O1(.1") Weight: lb (11.kg) 1 NOTE: With mains air at shaft rotation is clockwise. Reverse port connections for opposite rotation. Muffler supplied with motor.

11 PERFORMNCE V. PEK HP/. kw REVERSIBLE TORQUE (lbs ft.) GRPH 1 TORQUE - SPEED Bar PSI 7 PSI PSI 1 TORQUE (lbs ft.) GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE PRESSURE P.S.I. HORSE POWER GRPH POWER - SPEED PSI 7 PSI PSI Bar 1 POWER kw IR CONSUMPTION cu. ft/min. free air GRPH CONSUMPTION - SPEED PSI 7 PSI PSI Bar litres/sec. free air ttitude: The motor can be operated in all positions. irline filtration and lubrication: Use micron filtration or better. Choose a lubricator suitable for the flow required. Prior to start up, inject oil into the inlet port. Lubricator drop rate: - drops per minute continuous operation. 1-1 drops per minute intermittent operation. Polar Moment of Inertia: 1. lb.ins (. g.m). Maximum overhung force on shaft: 7 lbf (N) In certain circumstances this may be extended. Consult your Globe Distributor. xial loads should be kept down to a minimum. Maximum temperatures: - to +17 Farenheit. (- to + C ) 11

12 DIMENSIONS V MODEL VC I TC Configuration Ø1(.") OVERKEY.1(.9").9(.91") HOLES TPPED /" - 1 UNC ON 19.(.7") P.C.D. MOUNTING SPIGOT Ø11.(.") Ø11.(.97") Ø.(.7") Ø.1(.7") Ø.7(.17") Ø.7(.1") (.1") 1(.7") (.7") (.1") 1(.7") PORTS 1" N.P.T. 19(.") 7(.7") 7(.7") Ø7(1.") Ø1(.") Weight: lb (11.kg) MODEL VJ Foot Mounting Configuration 7 (.7") OVERKEY 1.1 (.1") 1. (.7") 11. (.") HOLES Ø 9 (11/") Ø19.(.7") Ø19.(.79").7(.17").7(.1") (1.1") (1.7") 9(1.") (7.97") (.9") 71(.") 1(.9") 7(."). 1(.") (1.79") PORTS 1" N.P.T. 9(.") 1(.") Ø7(1.") 1(.") 1(.1") Weight: lb (11.1kg) MODEL VX Face Mounting Configuration 7 (.7") 1.1 (.1") 1. (.7") HOLES TPPED /" - 1 UNC X 1 DEEP EQUISPCED ON 9. (.7") P.C.D. MOUNTING SPIGOT Ø 7. (.") Ø 7.1 (.99").7 (.17").7 (.1") Ø 19. (.7") Ø 19. (.79") (1.1") (1.7") (7.97") 71 (.") (.9") 1 PORTS (.9") 1" N.P.T. 9 (1.") 7 (.7") Ø 1 (.") Ø 7 (1.") 7 (.") 19 (.") WEIGHT lbs (11.1Kg) MODEL VSC D9 Flange Configuration Ø.9 (.9") Ø.99 (.97") Ø (7.7") 7. (1.9").71 (1.1") HOLES Ø 1(.7") EQUI-SPCED ON 1 (.9") P.C.D. MOUNTING SPIGOT Ø 1. (.111") Ø (.11") KEY (.1") SQURE X 7 (.7") DEEP X (1.") LONG ROUNDED ENDS 1 (.1") (1.97"). (.1") (.1") 1 (.9") TPPED HOLE IN SHFT. M X (.79") DEEP.. (.") 71 (.") HOLES M X 1 (.7") DEEP. 1 (.") 7 (.") 7 (.7") 7 (.") Ø 1 (.1") PORTS G 1" Ø 7 (1.") 7 (.7") 19 (.7") WEIGHT 7 lbs (1. Kg) 1 NOTE: With mains air at shaft rotation is clockwise. Reverse port connections for opposite rotation. Muffler supplied with motor.

13 PERFORMNCE V 7. HP/. kw REVERSIBLE TORQUE (lbs ft.) GRPH 1 TORQUE - SPEED PSI 7 PSI PSI Bar TORQUE (lbs ft.) 1 1 GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar 1 MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE PRESSURE P.S.I. HORSE POWER GRPH POWER - SPEED PSI PSI PSI Bar 1 POWER kw IR CONSUMPTION cu. ft/min. free air GRPH CONSUMPTION - SPEED PSI 7 PSI PSI Bar litres/sec. free air ttitude: The motor can be operated in all positions. irline filtration and lubrication: Use micron filtration or better. Choose a lubricator suitable for the flow required. Prior to start up, inject oil into the inlet port. Lubricator drop rate: -7 drops per minute continuous operation. 1-1 drops per minute intermittent operation. Polar Moment of Inertia:. lb.ins (1. g.m). Maximum overhung force on shaft: 1 lbf (N) In certain circumstances this may be extended. Consult your Globe Distributor. xial loads should be kept down to a minimum. Maximum temperatures: - to +17 Farenheit. (- to + C ) 1

14 DIMENSIONS V1 MODEL V1C 1 TC Configuration Ø 1 (.") 171. (.7") (7.") HOLES /" - 1 UNC EQUISPCED ON 19. (.") P.C.D. 1.7 (.") Optional foot available. Model V1Z MOUNTING SPIGOT Ø 11.7 (.99") Ø, (.7") Ø 11. (.9") Ø.1 (.7") (.1") KEY.7 (.1") SQ.. (1.") LG. (11.") 1 (.97") (.1") 1 (.") 11. (.") PORTS 1 1/" N.P.T. 1 (.") 9. (.7") 11. (.") 11. (.9") 9 (.") Ø (.") Ø 1 (.1") 17 (.") Weight lb (kg) MODEL V1J Foot Mounting Configuration 171. (.7") (7.") HOLES Ø 1. (.") KEY. (.") SQ.. (1.7") LG. Ø.7 (1.1") Ø. (1.1") (11.") 1 (7.91").7") 179. (7.") PORTS 1 1/" N.P.T. 1 (.") 9. (.7") 11. (.") 11. (.9") 1.7 (.") 9 (.") Ø 1 (.1") Ø (.") 17 (7.") Weight lb (kg) MODEL V1X Face Mounting Configuration HOLES. 7/1 " - 1 UNC X 1 DEEP EQUI-SPCED ON 1. ( 7/") P.C.D. (.") Ø 1 (.7") MOUNTING SPIGOT Ø.7 (1.1") Ø. (1.1") 1 (.") Ø 9. (.7") Ø 9.7 (.7").7") (11.") 9 (.") 1 (.") PORTS 1 1/" N.P.T. KEY. (.") SQ.. (1.7" LG.. (.9") 9 (.") Ø 1 (.1") Ø (.") 17 (.") Weight lb (1kg) MODEL VS1C D1 Flange Configuration Ø.9 (1.17") Ø 7.99 (1.1") Ø (9.") 1. (1.").71 (1.91") HOLES Ø 1 (.9") EQUISPCED ON 1 (.") P.C.D. Ø 1. (7.") Ø (7.1") MOUNTING SPIGOT KEY (.1") SQURE X 7 (.7") DEEP X (1.77") LONG ROUNDED ENDS (.") (.1") 11 (.") 1 (.9") 11 (.9") TPPED HOLE IN SHFT M1 X (1") DEEP. (.") (.1") HOLES M X 1 (.") (.") 1 (.97") 9 (.") 1 (.1") Ø 1 (.") PORTS G.1 1/" Ø (."). (.") 17 (.9") Weight lb (7kg) 1 NOTE: With mains air at shaft rotation is clockwise. Reverse port connections for opposite rotation. Muffler supplied with motor.

15 PERFORMNCE V1 1. HP/9. kw REVERSIBLE TORQUE (lbs ft.) GRPH 1 TORQUE - SPEED PSI 7 PSI PSI Bar TORQUE (lbs ft.) 1 GRPH STRTING TORQUE - PRESSURE 1 PRESSURE bar MXIMUM STRTING TORQUE MINIMUM STRTING TORQUE PRESSURE P.S.I. HORSE POWER GRPH POWER - SPEED GRPH CONSUMPTION - SPEED PSI 7 PSI PSI Bar POWER kw IR CONSUMPTION cu. ft/min. free air 1 9 PSI 7 PSI PSI Bar litres/sec. free air ttitude: The motor can be operated in all positions. irline filtration and lubrication: Use micron filtration or better. Choose a lubricator suitable for the flow required. Prior to start up, inject oil into the inlet port. Lubricator drop rate: -1 drops per minute continuous operation. 1-1 drops per minute intermittent operation. Polar Moment of Inertia: lb.in (. g.m). Maximum overhung force on shaft: lbf (17N) In certain circumstances this may be extended. Consult your Globe Distributor. xial loads should be kept down to a minimum. Maximum temperatures: - to +17 Farenheit. (- to + C ) 1

16 Globe irmotors Program Turbine Motor High lifetime of tools, up to 1. rpm. Power from to W. Compact ir Motor Reversible, compact, available with a wide range of incorporated reduction unit. Power from 1 to W. Vane Motor Reversible, available in flange, foot, or face execution. Power from, to 9, kw. Vane Motor with Gearbox vailable with planetary, coaxial, or worm gearboxes. lso possible with pneumatic brake. Compact Piston Motor High torque at low speed of rotation, very low air consumption and low noise level. Power from 11 to W. Radial Piston ir Motor vailable with proportional hand or remotely controlled valve, pneumatic brake and all types of gearboxes. Power from, to kw. DISTRIBUTOR Eikenlaan 1e NL- BP lphen a/d Rijn Tel: (+1)-()17- Fax: (+1)-()17-7 Website: info@globe-benelux.nl IRMOTORS B.V.