Axial Piston Fixed Motor A10FM / A10FE (US-Version)

Transcription

1 xial Piston Fixed Motor 10FM / 10FE (US-Version) R / /32 Replaces: Data sheet Series 52 Sizes 10 to 63 Nominal pressure 4000 psi (280 bar) Maximum pressure 5100 psi (350 bar) Open and closed circuit 10FM FE (2-hole-flange) 10FE (8-hole-flange) Contents Ordering code for standard program 2 Technical data 4 Dimensions 10FM size Dimensions 10FE size Flushing and boost pressure valve 26 nti cavitation valve 26 Speed sensor 27 Installation instructions 28 General instructions 32 Features Fixed motor in axial piston swashplate design for hydrostatic drives in open and closed circuit The output speed is proportional to the inlet flow The output torque increases with the pressure differential between the high and low pressure sides For use in mobile and industrial applications ong service life High permissible output speeds Well proven 10-rotary group technology High power to weight ratio compact design Plug-in version for space saving installation ow noise level Mechanical and hydraulic connections also according to SE standards Speed sensor optional Integrated anti cavitation valve optional, i.e. for fan drives

2 2/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Ordering code for standard program 10F M / 52 V C xial piston unit Swashplate design, fixed displacement, nominal pressure 4000 psi (280 bar), maximum pressure 5100 psi (350 bar) 10F Operating mode 02 Motor, open and closed circuit M Size (NG) 03 Theoretical displacement see page Series 04 Series 5, Index 2 52 Direction of rotation Viewed on drive shaft clockwise R 1) 05 counter-clockwise 1) bidirectional W Seals 06 FKM (fluor-caoutchouc) V Drive shaft Splined shaft to ISO (SE J744) m l l l l l l R 07 Splined shaft to ISO (SE J744) m m l l l l W Tapered with woodruff key and threaded end m l l l l l l C Mounting flange SE 2-hole m l l l l l l C Ports for service lines SE-flange ports and on side, same side, mounting bolts UNF l l l l l l 60N00 09 Threaded ports and, on side, same side, UNF thread m l l l l l l 66N00 Valves Without valves m l l l l l l 0 10 With integrated flushing valve l l l l l l 7 With integrated anti cavitation valve m l l l l l l 2 Speed sensor Without speed sensor m l l l l l l 11 Prepared for speed sensor (for inductive speed sensor ID) m l l l l m m D 1) Only necessary in conjunction with valve configuration 2 (integrated anti cavitation valve) = vailable m = On request = Not available

3 R / FM / 10FE Series 52 osch Rexroth Corp. 3/32 Ordering code for standard program 10F E / 52 V xial piston unit Swashplate design, fixed displacement, nominal pressure 4000 psi (280 bar), maximum pressure 5100 psi (350 bar) 10F Operating mode 02 Motor, open and closed circuit; plug-in design E Size (NG) 03 Theoretical displacement see page Series 04 Series 5, Index 2 52 Direction of rotation Viewed on drive shaft clockwise R 1) 05 counter-clockwise 1) bidirectional W Seals 06 FKM (fluor-caoutchouc) V Drive shaft Splined shaft to ISO (SE J744) m l l l l l l l l l l R 07 Splined shaft to ISO (SE J744) m m l l l l W Tapered with woodruff key and threaded end l l l l l l l l l l l C Mounting flange SE 2-hole l l l l l C 2) 08 Special 2-hole l l l l l l F Special 8-hole l l l l H Ports for service lines SE-flange ports and, on side, same side 09 mounting bolts metric l l l l l l 60N00 Threaded ports and, metric, on side, same side l l l l l l l l l l l 66N00 Valves Without valves m l m l l l l l l l l 0 10 With integrated flushing valve l l l l l l 7 With integrated anti cavitation valve l l l l l l l l l l l 2 Speed sensor Without speed sensor l l l l l l l l l l l 11 Prepared for speed sensor (for inductive speed sensor ID) m l l l l m m D 1) 2) Only necessary in conjunction with valve configuration 2 (integrated anti cavitation valve) Combination R-shaft with C-flange for sizes 10 to 18 in preparation = vailable m = On request = Not available

4 4/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Technical data Fluids Prior to project design, please see our technical data sheets RE (mineral oil) and RE (environmentally acceptable fluids) for detailed information on fluids and operating conditions. For operation on environmentally acceptable fluids please consult us (when ordering, please state in clear text the fluid to be used). Operating viscosity range To achieve optimum values for efficiency and service life we recommend an operation viscosity (at operating temperature) within the range, n opt = opt. operating viscosity SUS ( mm 2 /s) referred to the tank temperature (open circuit). imit of viscosity range For critical operation conditions the following values apply: n min = 42 SUS (5 mm 2 /s) (closed circuit) 60 SUS (10 mm 2 /s) (open circuit) for short periods (t 1 min) at a max. perm. temperature of 239 F (115 C). Please note that the max. leakage fluid temperature of 239 F (115 C) is also not exceeded in certain areas (for instance bearing area).the fluid temperature in the bearing area is approx. 9 F (5 C) higher than the average leakage fluid temperature n max = 7500 SUS (1600 mm 2 /s) for short periods (t 1 min) on cold start (t min = p 435 psi (30 bar), n 1000 min 1, -13 F ( 25 C)). t temperatures between -40 F (-40 C) and -13 F (-25 C) special measures are required, please consult us for further information. For detailed information on operation with low temperatures see data sheet RE Notes on the selection of the hydraulic fluid In order to select the correct fluid, it is necessary to know the operating temperature in the tank (open circuit) in relation to the ambient temperature. The fluid should be selected so that within the operating temperature range, the viscosity lies within the optimum range (n opt ), see shaded section of the selection diagram. We recommend to select the higher viscosity grade in each case. Example: at an ambient temperature of X F (X C) the operating temperature in the tank is 140 F (60 C). In the optimum viscosity range (n opt ; shaded area) this corresponds to viscosity grades VG 46 resp. VG 68; VG 68 should be selected. Important: The leakage fluid (case drain fluid) temperature is influenced by pressure and input speed and is always higher than the tank temperature. However, at no point of the component may the temperature exceed 239 F (115 C). If it is not possible to comply with the above conditions because of extreme operating parameters please consult us. Filtration of the hydraulic fluid Filtration improves the cleanliness level of the hydraulic fluid, which, in turn, increases the service life of the axial piston unit. To ensure the functional reliability of the axial piston unit, a gravimetric evaluation is necessary for the hydraulic fluid to determine the amount of contamination by solid matter and to determine the cleanliness level according to ISO cleanliness level of at least 20/18/15 to ISO 4406 is to be maintained. If above requirements cannot be maintained please consult us. Selection diagram F Viscosity ν [SUS (mm 2 /s)] C VG 68 VG 46 VG 32 VG 22 VG ν opt SUS mm 2 /s mm 2 /s C F SUS 42 t min = -40 F (-40 C) Fluid temperature range t max = 240 F (115 C)

5 R / FM / 10FE Series 52 osch Rexroth Corp. 5/32 Technical data Operating pressure range Pressure at service line port (pressure port) or Nominal pressure p nom 4000 psi (280 bar) absolute Maximum pressure p max 5100 psi (350 bar) absolute Single operating period 2,5 ms Total operating period 300 h Minimum pressure (high pressure side) 145 psi (10 bar) 2) Rate of pressure change R max _ psi/s (16000 bar/s) Pressure p p nom Dp Dt Definitions Nominal pressure p nom The nominal pressure corresponds to the maximum design pressure. Maximum pressure p max The maximum pressure corresponds to the maximum operating pressure within the single operating period. The sum of the single operating periods must not exceed the total operating period. Minimum pressure (high-pressure side) Minimum pressure at the high pressure side ( or ) which is required in order to prevent damage to the axial piston unit. Rate of pressure change R Maximum permissible rate of pressure rise and reduction during a pressure change over the entire pressure range. Time t Pressure p Single operating period Maximum pressure p max Nominal pressure p nom t 1 t 2 t n Outlet pressure at n max Minimum pressure at low pressure side p abs max _ 260 psi (18 bar) Case drain pressure Maximum permissible case drain pressure (at port, 1 ): p max abs motor operation in open circuit 60 psi(4 bar) abs p max abs motor operation in closed circuit 60 psi(4 bar) abs p max abs pump/motor operation in open circuit 30 psi(2 bar) abs Minimum pressure (high pressure side) Time t Total operating period = t 1 + t t n 1) 2) Other values on request ower pressures time dependent, please consult us. Direction of flow Viewed on drive shaft clockwise rotation to counter-clockwise rotation to

6 6/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Technical data Table of values (theoretical values, without efficiency and tolerances: valuea rounded) Size NG Displacement V g max in 3 (cm 3 ) 0.65 (10.6) 0.70 (11.5) 0.86 (14.1) 0.98 (16.1) Speed 1) at V g max n nom rpm (min -1 ) Input flow gpm at n nom q v max (/min) (53) (48) (59) (68) (76) (115) Power at n nom, Dp = 4000 psi (280 bar) ctual starting torque at n= 0 rpm (min -1 ), Dp = 4000 psi (280 bar) Torque p = 4000 psi at V g max (280 bar) Torsional stiffness R Drive shaft W C P max T max c c c HP (kw) lb-ft (Nm) lb-ft (Nm) lb-ft/rad (Nm/rad) lb-ft/rad (Nm/rad) lb-ft/rad (Nm/rad) 33 (24.7) 27.6 (37.5) 34.6 (47) 30 (22.5) 22.1 (30) 37.5 (51) 37 (27.6) 33.2 (45) 46.5 (63) 42 (31.6) 39.1 (53) 53.1 (72) 1.10 (18) 47 (35.3) 49.8 (67.5) 59 (80) (14835) (15084) (0.0006) (18662) (18662) ( ) (18662) ( ) (18662) ( ) 1.43 (23.5) 71 (53.6) 55.3 (75) 77.4 (105) (28478) (30017) 0.04 (0.0017) lb-ft Moment of inertia rotary group J TW (kgm 2 ) ( ) Maximum angular acceleration a rad/s Case volume Mass approx. V m gal () lbs (kg) 0.03 (0.1) 11.0 (5) 0.04 (0.15) 14.3 (6.5) 0.04 (0.15) 14.3 (6.5) 0.04 (0.15) 14.3 (6.5) 0.04 (0.15) 14.3 (6.5) 1) for maximum speed an outlet pressure (in low pressure side) of 261 psi (18 bar) is required (see diagram on page 7) 0.16 (0.6) 26.5 (12) Note Operation above the maximum values or below the minimum values may result in a loss of function, a reduced service life or in the destruction of the axial piston unit. We recommend testing the loads by means of experiment or calculation / simulation and comparison with the permissible values.

7 R / FM / 10FE Series 52 osch Rexroth Corp. 7/32 Technical data Table of values (theoretical values, without efficiency and tolerances: valuea rounded) Size NG Displacement V g max in 3 (cm 3 ) 1.73 (28.5) 2.24 (36.7) 2.71 (44.5) Speed 1) at V g max n nom rpm (min- 1 ) Input flow gpm at n nom q v max (/min) Power HP at n nom, Dp = 4000 psi (280 bar) P max (kw) ctual starting torque at n= 0 rpm (min -1 ), Dp = 4000 psi (280 bar) Torque p = 4000 psi at V g max (280 bar) Torsional stiffness R Drive shaft W C T max c c c lb-ft (Nm) lb-ft (Nm) lb-ft/rad Nm/rad lb-ft/rad Nm/rad lb-ft/rad Nm/rad 35.4 (134) 83 (62.5) 77.5 (105) 93.7 (127) (28478) (30017) Moment of inertia rotary group J TW lb-ft 2 kgm (0.0017) 40.7 (154) 95 (71.8) 92.2 (125) 120 (163) (46859) (38489) (46546) (0.0033) 47 (178) 111 (83.1) 125 (170) 146 (198) (46859) (38489) (46546) (0.0033) 3.53 (58) 55.2 (209) 130 (97.4) 151 (205) 190 (258) (80590) (60907) (87667) (0.0056) Maximum angular acceleration a rad/s Case volume Mass approx. V m gal () lbs (kg) 0.16 (0.6) 26.5 (12) 0.18 (0.7) 37.5 (17) 0.18 (0.7) 37.5 (17) 0.21 (0.8) 48.5 (22) 1) for maximum speed an outlet pressure (in low pressure side) of 261 psi (18 bar) is required (see diagram on this page) 3.84 (63.1) 56.8 (215) 133 (100.1) 169 (230) 207 (281) (80590) (60907) (87667) (0.0056) 0.21 (0.8) 48.5 (22) Note Operation above the maximum values or below the minimum values may result in a loss of function, a reduced service life or in the destruction of the axial piston unit. We recommend testing the loads by means of experiment or calculation / simulation and comparison with the permissible values. Permissible motor speed in relation to outlet pressure 1.0 Motor speed n/nmax (0) (2) (4) (6) (8) (10) (12) (14) (16) (18) Outlet pressure p ND [psi (bar)]

8 8/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Technical data Determination of motor size (NG) Input flow q v = V g n 231 η v = V g n 1000 η v [gpm] [/min] Torque T = V g Δp η mh [lb-ft] 24 π V g = Displacement per revolution in in 3 (cm 3 ) Δp = Differential pressure in psi (bar) n = Speed in rpm (min -1 ) η v = Volumetric efficiency η mh = Mechanical-hydraulic efficiency η t = Overall efficiency (η t = η v η mh ) T k = Torque constant T = 1.59 V g Δp η mh [Nm] 100 or T = T k Δp η mh Power P = T n = q v Δp η t [HP] P = 2 π T n = q v Δp η t [kw] Output speed n = q v 231 η v [rpm] V g n = q v 1000 η v [min -1 ] V g Permissible radial and axial forces of the drive shaft Size NG Max. radial force at X/2 Maximum axial force ± Fax Drive shaft R; W Fq X/2 X/2 X Drive shaft C Fq X/2 X/2 X F q max lb-f (N) ± F ax max lb-f (N) 56 (250) 90 (400) 79 (350) 157 (700) 79 (350) 157 (700) 79 (350) 157 (700) 79 (350) 157 (700) 270 (1200) 225 (1000) Size NG Max. radial force at X/2 Maximum axial force ± Fax Drive shaft R; W Fq X/2 X/2 X Drive shafte C Fq X/2 X/2 X F q max lb-f (N) ± F ax max lb-f (N) 270 (1200) 225 (1000) 337 (1500) 337 (1500) 337 (1500) 337 (1500) 382 (1700) 450 (2000) 382 (1700) 450 (2000)

9 R / FM / 10FE Series 52 osch Rexroth Corp. 9/32 Notes

10 10/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FM size FM 23-28/52W-VxCxxN000 efore finalising your design request a certified Flange ISO DI (ø ) 0 Port plate (9.5) 0.25 (6.3) 5.94 (150.8) 1.18 (30) 0.94 (23.8) (50.8) 1.48 (37.5) 6.85 (174) 5.75 (146) (64) 2.42 (61.5) 2.66 (67.5) DI 0.55 (ø14) 5.67 (144) 0.49 (12.5) 3.15 (80) DI 0.75 (ø19) 7.04 (178.8) 1.48 (37.5) 2.60 (66) 45 Port plate (9.5) 0.25 (6.3) 5.94 (150.8) 1.18 (30) 2.52 (64) 2.42 (61.5) 3.31 (84) 3.25 (82.5) DI 0.55 (ø14) Flange ISO DI (ø ) (31) 1.22 (31) 6.85 (174) 5.75 (146) (ø42) 5.67 (144) 0.49 (12.5) 3.15 (80) 7.04 (178.8) 2.60 (66) 45

11 R / FM / 10FE Series 52 osch Rexroth Corp. 11/32 Dimensions 10FM size Drive shafts efore finalising your design request a certified R Splined shaft 7/8 in 13T 16/32DP 1) (SE J744; 22-4()) C Tapered with woodruff key and threaded end (SE J744; 22-3()) 2) 3) 1/4-20UNC-2 Usable spline lenght 0.20 (5) 0.63 (16) 0.98 (25) 1.61 (41) (Ø ) DI Taper 125 : ) 3) 5/8-18UNF-2 DI 0.16 (Ø4) (3 ) 0.75 (19) 0.57 (14.4) (22) 2.19 (55.5) ( ) ( ) View ( ) Ports Designation Port for Standard Size 2) Max. pressure [psi (bar)] 4) State, Service line (high pressure series) SE J518 3/4 in 5100 (350) O Port plate 60 Mounting bolts ISO 68 3/8-16 UNC-2; 0.67 (17) deep, Service line ISO /16-12 UN-2; 0.63 (16) deep 5100 (350) O Port plate 66 Case drain ISO ) 3/4-16 UNF-2; 0.43 (11) deep 60 (4) O 5) 1 Case drain ISO ) 3/4-16 UNF-2; 0.43 (11) deep 60 (4) X 5) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Threaded end according to SME ) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 5) Depending on the installation position, or 1 must be connected (see also page 28). 6) The counterbore can be deeper than stipulated in the standard. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

12 12/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FM size FM 37-45/52W-VxCxxN000 efore finalising your design request a certified Port plate (9.5) 0.25 (6.3) 6.42 (163) 1.10 (28) 0.94 (23.8) 2.72 (69) 2.60 (66) 3.07 (78) 0.55 (ø14) Flange ISO DI (ø ) (50.8) 1.48 (37.5) 1.48 (37.5) 6.85 (174) 5.75 (146) (144) 0.49 (12.5) 3.31 (84) DI 0.75 (ø19) 7.60 (193) 2.72 (69) (125) Port plate 66 Flange ISO DI (9.5) 0.25 (6.3) 0 (ø ) 6.42 (163) 1.10 (28) (12.5) 3.31 (84) 7.60 (193) 1.34 (34) 1.34 (34) 6.85 (174) 5.75 (146) 5.55 (141) (69) 3.19 (81) 2.60 (66) 3.13 (79.5) DI 0.55 (ø14) 2.72 (69) (144) 1.65 (ø42) 4.92 (125)

13 R / FM / 10FE Series 52 osch Rexroth Corp. 13/32 Dimensions 10FM size Drive shafts efore finalising your design request a certified R Splined shaft 1 in 15T 16/32DP 1) (SE J744; 25-4(-)) C Tapered with woodruff key and threaded end (SE J744; 22-3()) 1/4-20UNC-2 2)3) Usable spline lenght 0.63 (16) 0.2 (5) 1.16 (29.5) 1.81 (45.9) DI (Ø25.16 ) M16 x 1.5 2) 4) Taper 125 : (18) (3 ) (30) 2.38 (60.6) Section ( ) ( ) ( ) W Splined shaft 7/8 in 13T 16/32DP 1) (SE J744; 22-4()) 1/4-20UNC-2 2)3) 0.2 (5) 0.63 (16) Usable spline lenght 0.98 (25) 1.61 (41) Ports Designation Port for Standard Size 2) Max. pressure [psi (bar)] 5) State, Service line (high pressure series) SE J518 3/4 in 5100 (350) O Port plate 60 Mounting bolts ISO 68 3/8-16 UNC-2; 0.83 (21) deep, Port plate 66 Service line ISO /16-12UN-2; 0.79 (20) deep Case drain ISO ) 7/8-14 UNF-2; 0.51 (13) deep 1 Case drain ISO ) 7/8-14 UNF-2; 0.51 (13) deep 5100 (350) O 60 (4) O 6) 60 (4) X 6) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Mounting bolt according to SME ) Threaded end according to DIN 13. 5) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 6) Depending on the installation position, or 1 must be connected (see also page 28). 7) The counterbore can be deeper than stipulated in the standard. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

14 14/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FM size FM 58-63/52W-VxCxxN000 efore finalising your design request a certified Port plate (9.5) 0.31 (7.8) 7.19 (182.5) 1.42 (36) 0.94 (23.8) 3.07 (78) 2.93 (74.5) 3.98 (101) DI 0.55 (ø14) Flange ISO DI (ø ) (50.8) 1.48 (37.5) 1.48 (37.5) 6.85 (174) 5.75 (146) (145) 0.49 (12.5) 3.84 (97.5) DI 0.75 (ø19) 8.17 (207.5) 3.01 (76.5) 45 Port plate (9.5) 0.31 (7.8) 7.19 (182.5) 1.42 (36) 3.07 (78) (4.09) (74.5) 4.02 (102) DI 0.55 (ø14) 0.04 (1) Flange ISO DI (ø ) (37.5) 1.48 (37.5) 6.85 (174) 5.75 (146) (ø48) DI 1.65 (ø42) 0.49 (12.5) 3.84 (97.5) 8.17 (207.5) 3.01 (76.5) 45

15 R / FM / 10FE Series 52 osch Rexroth Corp. 15/32 Dimensions 10FM size Drive shafts efore finalising your design request a certified R Drive shaft 1 1/4 in 14T 12/24DP 1) (SE J744; 32-4(C)) C Tapered with woodruff key and threaded end (SE J744; 32-3(C)) 5/16-18UNC-2 2)3) Usable spline lenght 0.24 (6) 0.75 (19) 1.57 (40) 2.18 (55.4) (Ø31.51 ) DI Taper 125 : ) 3) 1-12UNF (23.6) (3 ) (30) 2.61 (66.4) Section ( ) ( ) ( ) W Drive shaft 1 in 15T 16/32DP 1) (SE J744; 25-4(-)) 1/4-20UNC-2 2)3) 0.2 (5) 0.75 (16) Usable spline lenght 1.10 (28) 1.81 (45.9) Ports Designation Port for Standard Size 2) Max. press. [psi (bar)] 4) State, Service line (high pressure series) SE J518 3/4 in 5100 (350) O Port plate 60 Mounting bolts ISO 68 3/8-16 UNC-2; 0.83 (21) deep, Port plate 66 Service line ISO /16-12UN-2; 0.79 (20) deep Case drain ISO ) 7/8-14 UNF-2; 0.51 (13) deep 1 Case drain ISO ) 7/8-14 UNF-2; 0.51 (13) deep 5100 (350) O 60 (4) O 5) 60 (4) X 5) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Threaded end and mounting bolt according to SME ) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 5) Depending on the installation position, or 1 must be connected (see also page 28). 6) The counterbore can be deeper than stipulated in the standard. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

16 16/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FE size 10 10FE 10/52W-VxC66N000 efore finalising your design request a certified Flange ISO (55.5) 1.34 (34) 5.28 (134) 4.19 (106.4) 0.79 (20) DI 3.07 (ø78) DI (ø82.55 ) (85) (10) (7.6) 30 Y DI 3.94 (ø100) View Y 3.94 (100) 0.04 (ø11) 0.67 (17) 1.18 (30) 1.06 (27) 1.18 (30) 1.97 (50) 1.19 (48.5) 1.19 (48.5) DI 3.94 (ø100) 0.51 (13)

17 R / FM / 10FE Series 52 osch Rexroth Corp. 17/32 Dimensions 10FE size 10 Drive shaft efore finalising your design request a certified C Tapered shaft with woodruff key and threaded end (SE J744; 22-3()) (Ø ) DI Taper 125 : ) 2) 5/8-18UNF-2 DI 0.16 (Ø4) (24) 0.57 (14.4) (3 ) (22) 5.47 (139) Section ( ) ( ) ( ) Ports Designation Port for Standard Size 3) Max. pressure State [psi (bar)] 4), Service line ISO /8 UNF-2; 0.67 (17) deep 5100 (350) O Case drain ISO /16-18 UNF-2; 0.51 (13) deep 60 (4) O 5) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Threaded end according to SME ) Observe the general instructions on page 32 for the maximum tightening torques. 4) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 5) Depending on the installation position, or 1 must be connected (see also page 28). O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

18 18/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FE size FE 11-18/52W-Vxx66N000 efore finalising your design request a certified Mounting flange H Special flange 1.10 (28) (143.5) 3.74 (95) 0.25 (6.4) 0.39 (10) (4) DI 3.74 (ø95) (ø ) DI 0.26 (ø6.6) DI DI 4.80 (ø122) 1.91 (48.5) 1.85 (47) (34) 1.26 (32) 22.5 DI 4.41 (ø112) Mounting flange C flange to ISO (30.5) 6.02 (153) 3.84 (97.5) 0.37 (9.5) 0.49 (12.5) 6.85 (174) 5.75 (146) 30 DI 3.74 (ø95) DI (ø ) DI 4.80 (ø122) Y 0.94 (24) 5.98 (151.8) 1.34 (34) DI 0.55 (ø14) View Y 1.18 (30) 1.18 (30) 1.97 (50) ø (48.5) 1.91 (48.5) 8.16 (207.3) 0.51 (13)

19 R / FM / 10FE Series 52 osch Rexroth Corp. 19/32 Dimensions 10FE size Drive shafts efore finalising your design request a certified R 6) Splined shaft 3/4 in 11T 16/32DP 1) (SE J744; 19-4(-)) C Tapered with woodruff key and threaded end (SE J744; 22-3()) 1/4-20UNC-2 2)3) Usable spline lenght 0.19 (5) 0.55 (14) 0.83 (21) (Ø ) DI Taper 125 : ) 3) 5/8-18UNF-2 DI 0.16 (Ø4) (14.4) (3 ) (22) ( ) ( ) Section ( ) Mounting flange 1 Mounting flange 1 2 H 4.98 (126.6) H 5.68 (144.2) 0.75 (19) C C 5.98 (151.8) 0.95 (24) Ports Designation Port for Standard Size 2) Max. pressure State [psi (bar)] 4), Mounting flange C Service line ISO /8-14 UNC-2; 0.67 (17) deep 5100 (350) O, Mounting flange H Service line ISO /4-16 UNF-2; 059 (15) deep 5100 (350) O Case drain ISO /16-18 UNF-2; 0.51 (12) deep 60 (4) O 5) 1 Case drain ISO /16-18 UNF-2; 0.51 (13) deep 60 (4) X 5) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Threaded end and mounting bolt according to SME ) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 5) Depending on the installation position, or 1 must be connected (see also page 28). 6) Combination R-shaft with C-flange for size 11 to 18 in preparation. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

20 20/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FE size FE 23-28/52W-VxFxxN000 efore finalising your design request a certified Port plate (81) 3.02 (76.7) 0.49 (12.5) 0.94 (23.8) Y 2.99 (76) 5.83 (148) 2.46 (62.5) 2.66 (67.5) DI 0.55 (ø14) (ø ) 0 DI DI 4.57 (ø116) DI 2.60 (ø66) (50.8) 1.48 (37.5) 1.48 (37.5) 7.24 (184) 6.30 (160) 4.92 (125) (144) 0.50 (12.7) 3.23 (82) 0.87 (22) 4.12 (104.7) DI 0.75 (ø19) View Y 2.87 (73) 2.87 (73) 0.13 (3.4) 0.20 (5) Port plate (81) Y 3.02 (76.7) 0.08 (1.9) 3.31 (84) 2.99 (76) 3.25 (82.5) 5.83 (148) 2.64 (67) DI 0.55 (ø14) (ø ) 0 DI DI 4.57 (ø116) DI 2.60 (ø66) 1.22 (31) 1.22 (31) 7.24 (184) 6.30 (160) 4.92 (125) 1 DI 1.65 ø (144) 0.49 (12.5) 0.87 (22) 4.12 (104.7) 2.87 (73) 2.87 (73)

21 R / FM / 10FE Series 52 osch Rexroth Corp. 21/32 Dimensions 10FE size Drive shafts efore finalising your design request a certified R Drive shaft 7/8 in 13T 16/32DP 1) (SE J744; 22-4()) C Tapered with woodruff key and threaded end (SE J744; 22-3()) 1/4-20UNC-2 2)3) Usable spline lenght 0.19 (5) 0.63 (16) 0.98 (25) 4.53 (115.1) (Ø ) DI Taper 125 : ) 3) 5/8-18UNF-2 DI 0.16 (Ø4) (19) 0.57 (14.4) (3 ) (22) 5.10 (129.6) Section ( ) ( ) ( ) Ports Designation Port for Standard Size 2) Max. pressure [psi (bar)] 4) State, Service line (high pressure series) SE J518 3/4 in 5100 (350) O Port plate 60 Mounting bolts ISO 68 3/8-16 UNC-2; 0.83 (17) deep, Port plate 66 Service line ISO /16-12 UN-2; 0.79 (16) deep 5100 (350) O Case drain ISO ) 3/4-16 UNF-2; 11 deep 58 (4) O 5) 1 Case drain ISO ) 3/4-16 UNF-2; 11 deep 58 (4) X 5) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Threaded end and mounting bolt according to SME ) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 5) Depending on the installation position, or 1 must be connected (see also page 28). 6) The counterbore can be deeper than stipulated in the standard. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

22 22/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FE size FE 37-45/52W-VxFxxN000 efore finalising your design request a certified Port plate (88) Y 3.22 (81.9) 0.55 (14) 0.94 (23.8) 3.00 (76.3) 3.07 (78) 5.83 (148) 2.64 (67) DI 0.55 (ø14) DI (ø ) 5.19 (ø130) 2.75 (ø70) (50.8) 1.48 (37.5) 1.48 (37.5) 7.24 (184) 6.30 (160) 5.55 (141) (20) 5.67 (144) 0.50 (12.7) DI 0.75 (ø19) 1.10 (28) 4.41 (112) 3.46 (88) Y 3.22 (81.9) 0.55 (14) 3.19 (81) 2.69 (68.5) 3.13 (79.5) DI 0.55 (Ø14) DI 5.19 (ø130) DI 2.76 (ø70) (34) 1.34 (34) 7.24 (184) 6.30 (160) 0.79 (20) 5.67 (144) View Y DI (ø135 ) (73) 2.87 (73) 0.13 (3.4) 0.20 (5) Port plate (1.9) 0.50 (12.7) 1.10 (28) 4.41 (112) 2.79 (71) 2.87 (73) 5.71 (145)

23 R / FM / 10FE Series 52 osch Rexroth Corp. 23/32 Dimensions 10FE size Drive shafts efore finalising your design request a certified R Splined shaft 1 in 15T 16/32DP 1) (SE J744; 25-4(-)) C Tapered with woodruff key and threaded end (SE J744; 25-3(-)) 1/4-20UNC-2 2)4) Usable spline lenght 0.19 (5) 0.63 (16) 1.16 (29.5) 5.00 (127) (Ø ) DI Taper125 : (18) 2) 3) M16 x (3-0.2) 1.18 (30) 5.59 (142) Section ( ) ( ) ( ) W Splined shaft 7/8 in 13T 16/32DP 1) (SE J744; 22-4()) 1/4-20UNC-2 2)4) 0.19 (5) 0.63 (16) Usable spline lenght 0.98 (25) 4.80 (122) Ports Designation Port for Standard Size 2) Max. pressure [psi (bar)] 5) State, Service line (high pressure range) SE J518 3/4 in 5100 (350) O Port plate 60 Mounting bolts ISO 68 3/8-16 UNC-2; 0.83 (21) deep, Port plate 66 Service line ISO /16-12 UN-2; 0.79 (16) deep 5100 (350) O Case drain ISO ) 7/8-14 UNF-2; 13 deep 58 (4) O 6) 1 Case drain ISO ) 7/8-14 UNF-2; 13 deep 58 (4) X 6) 1) NSI 92.1a, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Threaded end according to DIN 13. 4) Mounting bolt according to SME ) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 6) Depending on the installation position, or 1 must be connected (see also page 28). 7) The counterbore can be deeper than stipulated in the standard. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

24 24/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Dimensions 10FE size FE 58-63/52W-VxFxxN000 efore finalising your design request a certified Port plate (90.1) 3.94 (100.2) 0.71 (18) 3.98 (101) DI (Ø ) DI 4.92 (Ø125) DI 3.15 (Ø80) Y 0.94 (23.8) 2.00 (50.8) 1.48 (37.5) 1.48 (37.5) 9.25 (235) 7.87 (200) 2.77 (70.5) (70.5) 5.71 (145) 1.17 (29.8) DI 0.75 (Ø19) 4.93 (125.2) DI 0.67 (Ø17) 1.89 (48)1.89 (48) 6.69 (170) View Y 2: (0.5)x (10) 0.21 (5.2 ) (15.5) DI (Ø ) DI 4.92 (Ø125) DI 3.15 (Ø80) 19 Port plate (90.1) 3.94 (100.2) 0.71 (18) Y 1.48 (37.5) 1.48 (37.5) DI 9.25 (235) 7.87 (200) 2.77 (70.5) (Ø153.7 ) (104) 4.01 (102) 0.79 (20) 0.04 (1) DI 1.65 (ø42) 2.77 (70.5) DI 1.89 (ø48) 1.17 (29.8) 4.93 (125.2) DI 0.67 (Ø17) 1.89 (48)1.89 (48) 6.69 (170)

25 R / FM / 10FE Series 52 osch Rexroth Corp. 25/32 Dimensions 10FE size Drive shafts efore finalising your design request a certified R Splined shaft 1 1/4 in 14T 12/24DP 1) (SE J744; 32-4(C)) C Tapered with woodruff key and threaded end (SE J744; 32-3(C)) 5/16-18UNC-2 2)3) Usable spline lenght 0.24 (6) 0.75 (19) 1.57 (40) 5.42 (137.7) (Ø ) DI Taper 125 : (23.6) 2) 3) 1-12UNF-2 DI 0.16 (Ø4) (14.1) (3 ) (30) 5.85 (148.7) Section ( ) ( ) ( ) W Splined shaft 1 in 15T 16/32DP 1) (SE J744; 25-4(-)) 1/4-20UNC-2 2)3) 0.20 (5) 0.63 (16) Usable spline lenght 1.10 (28) 5.05 (128.2) Ports Designation Port for Standard Size 2) Max. pressure [psi (bar)] 4) State, Service line (high pressure range) SE J518 3/4 in 5100 (350) O Port plate 60 Mounting bolts ISO 68 3/8-16 UNC-2; 0.83 (21) deep, Port plate 66 Service line ISO /16-12 UN-2; 0.79 (16) deep 5100 (350) O Case drain ISO ) 7/8-14 UNF-2; 13 deep 58 (4) O 5) 1 Case drain ISO ) 7/8-14 UNF-2; 13 deep 58 (4) X 5) 1) NSI 92.1a-1996, 30 pressure angle, flat base, flank centering, tolerance class 5 2) Observe the general instructions on page 32 for the maximum tightening torques. 3) Threaded end and mounting bolt according to SME ) Momentary pressure spikes may occur depending on the application. Keep this in mind when selecting measuring devices and fittings. 5) Depending on the installation position, or 1 must be connected (see also page 28). 6) The counterbore can be deeper than stipulated in the standard. O = Must be connected (plugged on delivery) X = Plugged (in normal operation)

26 26/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Flushing and boost pressure valve Ordering Option N007 This valve assembly is used to flush an unacceptable heat load out of the closed loop circuit, and to maintain the necessary minimum boost pressure (230 psi (16 bar), fixed setting). The valve is integrated into the port plate. built-in fixed orifice determines the flushing flow, which is taken out of the low pressure side of the loop and directed into the motor housing. It leaves the housing together with the case drain flow. This combined flow is replenished with fresh oil by means of the boost pump. Dimensions 10FM / 10FE Port plate 60 Port plate66 Standard flushing flow With low press. side p ND = 290 psi (20 bar) and an orifice dia in (1.6 mm): 1.45 gpm (5.5 /min) (sizes 23-63). Other orifice diameters are available, please state in clear text. Further flushing flows for sizes see table: Flushing flow [gpm (/min)] efore finalising your design request a certified Orifice ø [in (mm)] 0.92 (3.5) 0.05 (1.2) 1.45 (5.5) 0.06 (1.6) 2.48 (9) 0.08 (2) Schematic Port for ; Service line, 1 Case drain ( 1 plugged) 1 Size (NG) / (72) 283 (72) 37/ (77) 3.03 (77) 58/ (77) 3.23 (82) nti cavitation valve Ordering option N002 When stopping a system with a relatively large mass (i.e. fan drive) the anti-cavitation valve provides fluid to the motor inlet during the coasting time. Schematic Clockwise rotation Counter clockwise rotation The valve assembly is integrated inside the port plate. Important It is necessary to specify a direction of rotation (clockwise or counter clockwise) looking at the shaft end of the motor. The outside dimensions are identical to the standard units except the 10FE with the 8-hole mounting flange, for the difference in lenght, before finalising your design request a certified 1 1 Port for ; Service line, 1 Case drain ( 1 plugged)

27 R / FM / 10FE Series 52 osch Rexroth Corp. 27/32 Speed sensor Ordering option D The version 10FM...D comprises gearing around the rotary unit (prepared for speed pickup). In this case, the rotating cylinder barrel can provide a speed dependent signal, which can be picked up by a suitable sensor and processed for further evaluation. Sensor port (D) will be closed for delivery. motor, prepared for speed sensing will be delivered without the necessary accessory parts which must be ordered separately. Inductive speed sensor ID R 18/ (see RE 95130) and mounting parts (spacer and 2 seals per kit) can be ordered separately with the following part numbers: Schematic D 1 efore finalising your design request a certified Size (NG) Ordering Nr. Nr. of teeth 23/28 R /45 R /63 in preparation 9 Port for ; Service line, 1 Case drain ( 1 plugged) Dimensions 10FM...D D Size (NG) Port D (plugged) 23/ (61) 37/ (66) 58/ (69) 0.61 (15.5) 0.67 (17) 0.58 (14.8) 4.00 (101.8) 3.31 (84.2) 5.60 (128.5) M18 x 1.5 M18 x 1.5 M18 x FE...D Size (NG) Port D (plugged) 3 D / (61) 37/ (66) 58/ (69) 0.61 (15.5) 0.67 (17) 0.58 (14.8) 1.09 (27.7) 1.33 (33.9) 1.81 (46.1) M18 x 1.5 M18 x 1.5 M18 x 1.5

28 28/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Installation instructions General t all times, the axial piston unit must be filled with fluid and air bled during commissioning and operation. This must also be observed after a prolonged period of standstill as the system may drain back to the reservoir via the hydraulic lines. The case drain fluid in the motor housing must be directed to tank via the highest available tank port and must drain the fluid below the minimum fluid level in the reservoir. Installation position See following examples 1 to 8. Recommended installation positions: 1 and 3 resp. 2 and 4. dditional installation positions are available on request. elow reservoir installation (standard) elow reservoir installation means, that the motor is mounted below the minimum fluid level. bove reservoir installation bove reservoir installation means, that the motor is mounted above the minimum fluid level. check valve in the case drain line is only permissible under certain conditions; please consult us S S 1 F 1 F 1 1 / / / / S S S S F / F / / / S S Install. position ir bleed Filling Install. position ir bleed Filling 1, 2 1 5, 6 F 1 (F) 3, 4 7, 8 F (F) / 1 = Case drain port, F = ir bleed resp. filling port, S = affle.

29 R / FM / 10FE Series 52 osch Rexroth Corp. 29/32 Notes

30 30/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 Notes

31 R / FM / 10FE Series 52 osch Rexroth Corp. 31/32 Notes

32 32/32 osch Rexroth Corp. 10FM / 10FE Series 52 R /03.12 General instructions The motor 10FM and 10FE has been designed to be used in open and closed circuits. Project planning, assembly and commissioning of the axial piston unit require the involvement of qualified personnel. efore operating the axial piston unit read the relevant operating manual thoroughly and completely. If needed request this information from Rexroth During and shortly after operation, there is a risk of burns on the axial piston unit and especially on the solenoids. Take appropriate safety measures (e.g. by wearing protective clothing). --Pressure ports: The ports and fastening threads are designed for the specified maximum pressure. The machine or system manufacturer must ensure that the connecting elements and lines correspond to the specified operating conditions (pressure, flow, hydraulic fluid, temperature) with the necessary safety factors. The service line ports and function ports are only designed to accommodate hydraulic lines. The data and notes contained herein must be adhered to. The product is not approved as a component for the safety concept of a general machine according to DIN The following tightening torques apply: --Fittings: Observe the manufacturer s instructions regarding the tightening torques of the fittings used. --Mounting bolts: For mounting bolts with metric thread according to DIN 13 or threads according SME 1.1 we recommend checking the tightening torque individually according to VDI Mounting bolts threads and threaded ports in the axial piston unit: The maximum permissible tightening torques M G max are maximum values for the female threads and must not be exceeded. For values, see the following table. --Threaded plugs: For the threaded plugs, supplied with the axial piston unit, the required tightening torques M V apply. For values, see the following table. Ports Standard Thread sizes Maximum permissible tightening torque for the female threads M G max Required tightening torque for the threaded plugs M V ISO /4-16 UNF lb-ft (160 Nm) 45 lb-ft (62 Nm) 5/16 in 7/8-14 UNF lb-ft (240 Nm) 92 lb-ft (127 Nm) 3/8 in 9/16-18 UNF-2 58 lb-ft (80 Nm) 17 lb-ft (25 Nm) 1/4 in 1 1/16-12 UN lb-ft (360 Nm) 107 lb-ft (147 Nm) 9/16 in WF hexagon socket of the threaded plugs osch Rexroth Corporation xial & Radial Piston Units 8 Southchase Court Fountain Inn, SC US Telephone (864) Facsimile (864) osch Rexroth Corporation xial & Radial Piston Units 2315 City ane Road ethlehem, P US Telephone (610) Facsimile (610) osch Rexroth Corporation ll rights reserved. Neither this document, nor any part of it, may be reproduced, duplicated, circulated or disseminated, whether by copy, electronic format or any other means, without the prior consent and authorization of osch Rexroth Corp. The data and illustrations in this brochure/data sheet are intended only to describe or depict the products. No representation or warranty, either express or implied, relating to merchantability or fitness for intended use, is given or intended by virtue of the information contained in this brochure/data sheet. The information contained in this brochure/data sheet in no way relieves the user of its obligation to insure the proper use of the products for a specific use or application. ll products contained in this brochure/data sheet are subject to normal wear and tear from usage. Subject to change.