Fixed Displacement Motor A2FM

Transcription

1 rueninghaus Hydromatik Series 6, for use in open and closed circuits xial tapered piston - bent axis design Sizes Nom. Pressure up to 400 bar Peak Pressure up to 4 bar RE 91001/01.97 RE 91001/01.97 replaces he fixed displacement motor 2FM of axial piston, bent axis design is made suitable for hydrostatic drives in open and closed circuits. Output speed is proportional to input flow and inversely proportional to displacement. Drive torque increases with the pressure drop across the unit. he motor is suitable for use in mobile and industrial applications. Careful selection of the displacements offered, permit sizes to be matched to practically every application. Favourable power / weight ratio Compact and economic design Optimum efficiency One piece pistons with piston rings Patented cylinder block drive system rueninghaus Hydromatik 1/28

2 RE 91001/01.97 Ordering Code / Standard Program (Ordering code size 5 see page 8) Hydraulic fluid Mineral oil (no code) HF-fluids sizes (no code) sizes (only in connection with drive shaft bearings L) E- xial piston unit ent axis design, fixed displacement 2F Drive shaft bearings Mechanical bearings (no code) Long-Life bearings L Mode of operation Motor (Plug-in motor 2FE see RE 91008) M Size Displacement V g (cm 3 ) Sizes : production plant Elchingen; Sizes : production plant Horb Series 6 Index sizes size sizes Direction of rotation viewed on shaft end alternating W Seals NR (nitril-caoutchouc) P NR (nitril-caoutchouc), shaft seal in FPM N FPM (fluor-caoutchouc) V Shaft end Splined shaft DIN 5480 Z Parallel shaft with key, DIN 6885 P Mounting flange ISO 4-hole ISO 8-hole H = available = not available = preferred program (preferred types see page 22) 2/28 rueninghaus Hydromatik

3 RE 91001/ F M / 6 W - Hydraulic fluid xial piston unit Drive shaft bearings Mode of operation Size Series Index Direction of rotation Seals Shaft end Mounting flange Service line connections 1 ) Ports and SE, at rear end Ports and SE at side, opposite side Ports and threads, at side, opposite side Ports and threads, at side and rear end Ports and SE at side, same side port plate with integrated pressure relief valves Valves without valves (no code) 0 with pressure relief valves (without pressure sequence range) 1 with pressure relief valves (with pressure sequence range) 2 with integrated flushing valve 6 with built-on flushing and boost valve 7 Speed sensing control without speed sensing control (no code) prepared for speed sensing control D 1 ) hreads of fixing screws and service lines are metric rueninghaus Hydromatik 3/28

4 echnical Data Fluid We request that before starting a project detailed information about the choice of pressure fluids and application conditions are taken from out catalogue sheets RE (mineral oil), RE (environmentally acceptable hydraulic fluids) and RE (fire resistance fluids, HF). When using HF- or environmentally acceptable hydraulic fluids possible limitations for the technical data have to be taken into consideration. If necessary please consult our technical department (please indicate type of the hydraulic fluid used for your application on the order sheet). Operating viscosity range In order to optain optimum efficiency and service life, we recommend that the operating viscosity (at operating temperature) be selected from within the range: ν opt = operating viscosity mm 2 /s referred to the loop temperature (closed circuit) or tank temperature (open circuit). Viscosity limits he limiting values for viscosity are as follows: sizes ν min =5 mm 2 /s, short term at a max. permissible temperature of t max = 115 C ν max = 1600 mm 2 /s, short term on cold start (t min = -40 C) sizes ν min = 10 mm 2 /s short term at a max. permissible leakage oil temp. of t max = 90 C ν max = 1000 mm 2 /s, short term on cold start (t min = -25 C) Please note that the max. fluid temperature is also not exceeded in certain areas (for instance bearing area). t temperatures of -25 C up to -40 C special measures may be required for certain installation positions. Please contact us for further information. Selection diagram viscosity ν (mm 2 /s) t min = -40 C VG VG 32 VG 68 VG 46 VG 100 fluid temperature range 1600 ν opt temperature t ( C) t max = +115 C Notes on the selection of the hydraulic fluid In order to select the correct fluid, it is necessary to know the operating temperature in the loop (closed circuit) or the tank temperature (open circuit) in relation to the ambient temperature. he hydraulic fluid should be selected so that within the operating temperature range, the operating viscosity lies within the optimum range (ν opt ) (see shaded section of the selection diagram). We recommend that the highest possible viscosity range should be chosen in each case. Example: t an ambient temperature of X C the operating temperature (closed circuit: loop temperature; open circuit: tank temperature) is 60 C. Within the operating viscosity range (ν opt ; shaded area), this corresponds to viscosity ranges VG 46 or VG 68. VG 68 should be selected. Important: he leakage oil (case drain oil) temperature is influenced by pressure and motor speed and is always higher than the circuit or tank temperature. However, at no point in the circuit may the temperature exceed 115 C for sizes or 90 C for sizes If it is not possible to comply with the above conditions because of extreme operating parameters or high ambient temperatures please consult us. Filtration he finer the filtration the better the achieved purity grade of the pressure fluid and the longer the life of the axial piston unit. o ensure the functioning of the axial piston unit a minimum purity grade of: 9 to NS to SE 18/15 to ISO/DIS 4406 is necessary. t very high temperatures of the hydraulic fluid (90 C to max. 115 C, not permissible for sizes !) at least cleanless class 8 to NS to SE 17/14 to ISO/DIS 4406 is necessary. If above mentioned grades cannot be maintained please consult supplier. Direction of Flow Clockwise rotation to nti-clockwise rotation to Speed range here is no limitation on minimum speed n min. If uniformity of rotation is required, however, speed n min should not be allowed to fall below rpm. See table on page 6 for max. permissible speeds. Installation position ny installation position possible. he motor housing must be filled with fluid prior the commissioning, and must remain full whenever it is operating. For extensive information on installation postition, please consult our data sheet RE before completing your design work. Symbol, Service line ports Drain port 4/28 rueninghaus Hydromatik

5 RE 91001/01.97 echnical Data Case drain pressure he lower the speed and the case drain pressure the higher the life expectation of the shaft seal ring. Shaft seal ring FPM (fluor-caoutchouc) he values shown in the diagram are permissible loads of the seal ring and shall not be exceeded. t stationary pressure loads in the range of the max. admissible leakage pressure a reduction of the life experience of the seal ring will result. For a short period (t < 5 min.) are for the sizes pressure loads up to 5 bar independent from rotational speeds are permissible. Sizes perm. pressure p abs. max. (bar) Sizes perm. pressure p abs. max. (bar) ,5 3 2,5 2 1,5 sizes 80,90 sizes 107,125 sizes 160,180 size size 0 size 710 sizes 10,12, sizes 23,28,32 size 45 sizes 56, speed n (rpm) size 2 size 355 size speed n (rpm) Shaft seal ring NR (nitril-caoutchouc) For seal rings of NR 33% reduced values for the max. permissible housing pressure p abs.max. are to be considered compared with seals of FPM. Special operation conditions may require limitations of these values. Note: - maximum permissible motor speeds are given in the table on page 6 - max. perm. housing pressure p abs. max 10 bar (sizes ) 4 bar (sizes ) - the pressure in the housing must be the same as or greater than the external pressure on the shaft seal. Flushing valve In order to prevent excessive heat build-up in closed circuit operation, it is possible to fit a flushing valve (built into the port plate). wo such valves are available: - an Integrated flushing valve (built into the port plate) (sizes ) - a built-on flushing and boost pressure relief valve (sizes , 2) Integrated flushing valve (6) - switching pressure p 8 bar (this value is lower than the starting pressure of an unloaded motor). 2 () - closed in centre position ( p < 8 bar). Sizes Flushing- 2,5 3,1 4,1 volume L/min (values given for low pressure p = 25 bar) 1 () uilt-on flushing and boost pressure relief valve (7) his valve is built on to the fixed displacement motor. It must then be noted that only a port plate with ports at side is then available (port plate 02). he flushing and boost pressure relief valve has a fixed setting of 16 bar (the setting of the primary boost pressure relief valve must be noted) and is used to safeguard the minimum boost pressure. fixed flow of fluid is taken via an orifice from the low pressure side of the circuit and fed into the motor housing. his flow is then passed back to tank with the case drain fluid. Fluid thus removed from the closed circuit must be made up by means of the boost pump. Different orifice sizes may be used to select varying flows of flushing fluid. Flows (at low pressure p = 25 bar) * Size Flow Orifice No. 45, 56, 63 3,5 L/min / , 90 5 L/min / , L/min / , L/min / L/min * Standard flushing volumes (for sizes flushing volumes of 3,5-10 L/min can be supplied. If a flushing volume different from the standard flushing volume is required, please indicate the requested orifice in clear text when ordering). 1 2 () () Long-Life bearings (L) (sizes ) (for high life expectancy and use of HF-fluids) he outer dimensions of the axial piston motors are identical to standard design (without long life bearings). he change from standard design to long life bearing system is possible. We recommend to apply bearing flushing at port U. earing flushing For sizes bearing and housing flushing is possible through port U. rueninghaus Hydromatik 5/28

6 RE 91001/01.97 echnical Data Working pressure range Maximum pressure at port or (Pressure data to DIN 24312) Size 5 Shaft end Shaft end C 210 bar 315 bar Peak pressure p max 2 bar 3 bar Sizes Shaft end Shaft end Z,, P 400 bar 3 bar *) Peak pressure p max 4 bar 400 bar *) ttention: shaft end Z and P with drives of radial force loads at the drive shaft (pinion V-belt drives) necessitate reduction of the nominal pressure to = 315 bar (please contact us). Sizes Peak pressure p max 3 bar 400 bar Speed sensor (D) (sizes ) Version 2FM D (suitable for fitting speed sensor) includes gearing on the rotary group and in addition the port M in which a speed sensor is screwed in. speed-proportional signal is produced by means of the rotating, splined rotary group which can be picked up by a suitable sensor and fed back for evaluation. he speed sensor can be screwed into port M (thread M18x1,5). Sizes No. of teath length of 12,7 11,2 14,7 14,7 14,7 14,7 thread (mm) he speed sensor is not included in standard supply. Suitable sensors (order seperately): - Induktive impulse detector ID (see RE 938) - Hall effect speed sensor HD (see RE 942) With pulsating loads above 315 bar we recommend using the model with splined shaft, standard version (sizes ) or with splined shaft Z (sizes ). he summ of the pressures at ports and may not exceed 700 bar (630 bar, 2F 5). able of values (theoretical values, without considering η mh and η v ; values rounded) Size Displacement V g cm 3 4,93 10, ,9 28, ,6 56, ,4 Max. speed n max rpm n max intermittent1 ) rpm Max. flow q V max L/min orque constants K Nm/bar 0,076 0,164 0,19 0,25 0,36 0,445 0,9 0,725 0,89 1,0 1,27 orque at p Nm 24,7 2 ) p = 400 bar Nm Case volume L 0,17 0,17 0,17 0,20 0,20 0,20 0,33 0,45 0,45 0,55 Moment of inertia about drive axis J kgm 2 0, ,0004 0,0004 0,0004 0,0012 0,0012 0,0012 0,0024 0,0042 0,0042 0,0072 Weight (approx) m kg 2,5 5,4 5,4 5,4 9,5 9,5 9,5 13, Size Displacement V g cm , , Max. speed n max rpm n max intermittent1 ) rpm Max. flow q V max L/min orque constants K Nm/bar 1,43 1,70 1,99 2,54 2,86 3,18 3,98 5,64 7,95 11,3 15,9 orque at p Nm p = 400 bar Nm Case volume L 0,55 0,8 0,8 1,1 1,1 2,5 3,5 7,8 Moment of inertia about drive axis J kgm 2 0,0072 0,0116 0,0116 0,0220 0,0220 0,0378 0,061 0,102 0,178 0,55 0,55 Weight (approx.) m kg ) Intermittent max. speed: overspeed at discharge and overtaking travel operations, t < 5 sec. and p < 1 bar 2 ) p 6/28 rueninghaus Hydromatik

7 RE 91001/01.97 echnical Data Output drive Permissible axial and radial loads on drive shaft he values given are maximum values and do not apply to continuous operation Size a mm F q max N ±F ax max N ±F ax perm. /bar N/bar 1,5 3,0 3,0 3,0 5,2 5,2 5,2 7,0 8,7 8,7 10,6 Size a mm ,5 52,5 67,5 67,5 F q max N ) 10 1 ) ) ) ) ±F ax max N +F ax max F ax max ±F ax perm. /bar N/bar 10,6 12,9 12,9 16,7 16,7 16,7 2 ) 2 ) 2 ) 2 ) 2 ) 1 ) xial piston unit in stationary or in bypass operation, please contact us when appearing higher forces! 2 ) Please contact us! Code explanation a = distance of F q from shaft shoulder F q max = max. perm. radial force at distance a (at intermittent operation) ±F ax max = max. perm. axial force when stationary or when axial piston unit is running at zero pressure ±F ax perm. /bar = perm. axial force/bar operating pressure he direction of the max. perm. axial force must be noted by sizes F ax = increases bearing life + F ax = reduces bearing life (avoid if possible) Calculation of size V g n Flow q V = in L/min 1000 η v Optimal force direction of F q (valid for sizes ) y means of appropriate force directions of Fq the bearing load caused by inside rotary group forces can be reduced. n optimal life expectation of the bearing can be reached. q V 1000 η v Output speed n = in rpm V g V g p η mh alternating rotation ϕ opt = ϕ opt = Output torque = 20 π 1,59 V g p η mh = in Nm 100 ϕ opt = 70 ϕ opt = 70 = K p η mh in Nm 2 π n n Output power P = = q V p = η t in kw 600 V g = geometric displacement per rev. in cm 3 = torque in Nm p = pressure differential in bar n = speed in rpm K = torque constants in Nm/bar η v = volumetric efficiency η mh = mech.-hyd. efficiency η t = overall efficiency anti-clockwise rotation pressure at port clockwise rotation pressure at port anti-clockwise rotation pressure at port rueninghaus Hydromatik 7/28

8 efore finalising your design, please request a certified drawing. Unit Dimensions, Size 5 h8 8 17,5 74,5 58,5 Y R 6 70 Detail Y ø ø48,5 75 ±0,1 6,4 70, Service line ports M 18x1,5 Drain port M 10x1, both sides 62 Shaft ends Parallel shaft with C apered shaft with spigot key 4x4x20 and spring washer 3x5 DIN 6885 DIN , ,5 ø12 k6 M4 ø12,8 M10x1 10 R0,4 = 210 bar taper 1:10 = 315 bar Ordering Code / Standard Program Size 5 xial piston unit ent axis design, fixed displacement 2F Size Displacement V g (cm 3 ) 5 Direction of rotation viewed on shaft end alternating W Series 2F 5 W dditional instructions in text form Seals he fixed motor 2F5 is equipped with NR (Nitrilcaoutchouc) seals in standard design. In case of need FPM- (fluor-caoutchouc) seals please indicate when ordering in clear text: with FPM-seals Shaft end Parallel shaft with key DIN 6885 apered shaft with spigot and spring washer DIN 6888 C Service line connections hreads at side, metric 3 = preferred program (preferred types see page 22) 8/28 rueninghaus Hydromatik

9 efore finalising your design, please request a certified drawing. Unit Dimensions, Sizes 10, 12, ,5 1 5 see port plates R ø80 h ,5 5 41, Shaft ends Sizes 10, 12, 16 Sizes 10, 12 Splined shaft Z Splined shaft W 25x1,25x30x18x9g W 20x1,25x30x14x9g DIN 5480 DIN R1,6 16 R 1,2 E1x0,2 DIN 9 E1x0,2 DIN 9 M 10 ø21,6 M 6 ø16,6 28 ø25 k6 M 10 ø24,6 22,5 ø20 k6 M 6 ø19, ,2 ø85, Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 12x1,5 Sizes 10, 12, 16 Sizes 10, 12 Parallel shaft with P Parallel shaft with key S 8x7x32 key S 6x6x32 DIN 6885 DIN , ,5 40 = 400 bar Port plates ,5 55,5 69, , , , Service line ports M 22x1,5,, 1, 1 Service line ports M 22x1,5 rueninghaus Hydromatik 9/28

10 efore finalising your design, please request a certified drawing. Unit Dimensions, Sizes 23, 28, 32 60, see port plates R 12 ø100 h6 55, , ,2 2 ø106, Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 16x1,5 Shaft ends Sizes 23, 28, 32 Sizes 23, 28 Splined shaft Z Splined shaft W 30x2x30x14x9g W 25x1,25x30x18x9g DIN 5480 DIN 5480 Sizes 23, 28, 32 Sizes 23, 28 Parallel shaft with P Parallel shaft with key S 8x7x40 key S 8x7x40 DIN 6885 DIN R1,6 19 R 1,6 E1x0,2 DIN 9 E1x0,2 DIN 9 M 10 ø24,6 M 8 ø21,6 33 ø30 k6 M 10 ø29,6 28 ø25 M 8 k6 ø24, = 400 bar prepared for speed sensing control (D), with port M (inductive impulse detector ID see RE 938 hall effect speed sensor HD see RE 942, to be ordered separately!) 60,7 2 M M 18 x 1, /28 rueninghaus Hydromatik

11 efore finalising your design, please request a certified drawing. Sizes 23, 28, 32 Port plates ,5 40,5 18,2 40, , M8; 15 deep M8; 15 deep , Service line ports SE 1 / 2, Service line ports SE 1 / , Service line ports M 27x2,, 1, 1 Service line ports M 27x (see page 28) 149 Detail Y M8; 15 deep 18,2 40,5 40,5 115 Y, Service line ports SE 1 / 2 rueninghaus Hydromatik 11/28

12 efore finalising your design, please request a certified drawing. Unit Dimensions, Size 45 60, see port plates R ø125 h , Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 18x1,5 Shaft ends Splined shaft Z Splined shaft P Parallel shaft with W 32x2x30x14x9g W 30x2x30x14x9g key S 8x7x DIN 5480 DIN 5480 DIN R1,6 28 R1,6 E1x0,2 DIN 9 M 12 ø26,6 M 12 ø24,6 33 ø30 k6 M 12 ø29, = 400 bar prepared for speed sensing control (D), with port M (inductive impulse detector ID see RE 938 hall effect speed sensor HD see RE 942, to be ordered separately!) with built-on flushing and boost valve (7) ,3 5,5 M M 18 x 1,5 Y ,5 13, ø118 Detail Y 98 12/28 rueninghaus Hydromatik

13 efore finalising your design, please request a certified drawing. Size 45 Port plates ,8 147,8, , , M 10; 17 deep M 10; 17 deep , Service line ports SE 3 / 4, Service line ports SE 3 / Detail Y , M 10; 17 deep 23,8,8 Y,, 1, 1 Service line ports M 33x2, Service line ports SE 3 / 4 19 (see page 28) rueninghaus Hydromatik 13/28

14 efore finalising your design, please request a certified drawing. Unit Dimensions, Sizes 56, , see port plates R 16 ø125 h ,5 1, Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 18x1,5 Shaft ends Sizes 56, 63 Size 56 Splined shaft Z Splined shaft W 35x2x30x16x9g W 30x2x30x14x9g DIN 5480 DIN 5480 Sizes 56, 63 Size 56 Parallel shaft with P Parallel shaft with key S 10x8x key S 8x7x DIN 6885 DIN R1,6 28 R1,6 E1x0,2 DIN 9 E1x0,2 DIN 9 M ø29,6 M Y 159 ø24,6 k6 38 ø35 M ,5 60 ø34,6 33 ø30 k6 M 12 ø29,6 2,5 = 400 bar prepared for speed sensing control (D), with port M (inductive impulse detector ID see RE 938 hall effect speed sensor HD see RE 942, to be ordered separately!) with built-on flushing and boost valve (7) 67,5 6 M M 18 x 1, ø128 Detail Y 98 14/28 rueninghaus Hydromatik

15 efore finalising your design, please request a certified drawing. Sizes 56, 63 Port plates , ,8,8 23,8 19,8 166,5 23, M 10; 17 deep M 10; 17 deep , Service line ports SE 3 / 4, Service line ports SE 3 / , Detail Y M 10; 17 deep,8,8 23,8 Y,, 1, 1 Service line ports M 33x2, Service line ports SE 3 / 4 19 (see page 28) rueninghaus Hydromatik 15/28

16 efore finalising your design, please request a certified drawing. Unit Dimensions, Sizes 80, 90 78, see port plates 165 R 16 ø140 h , ø138, Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 18x1,5 Shaft ends Sizes 80, 90 Size 80 Splined shaft Z Splined shaft W 40x2x30x18x9g W 35x2x30x16x9g DIN 5480 DIN 5480 Sizes 80, 90 Size 80 Parallel shaft with P Parallel shaft with key S 12x8x56 key S 10x8x56 DIN 6885 DIN R2,5 28 R 1,6 E1x0,2 DIN 9 E1x0,2 DIN 9 M ø34, with built-on flushing and boost valve (7) 268 Y 173,5 M 12 ø29,6 k6 43 ø40 M ,5 70 ø39,6 38 ø35 k6 M ,5 70 ø34,6 = 400 bar prepared for speed sensing control (D), with port M (inductive impulse detector ID see RE 938 hall effect speed sensor HD see RE 942, to be ordered separately!) 78,5 6 M M 18 x 1,5 65,8 Detail Y 98 16/28 rueninghaus Hydromatik

17 efore finalising your design, please request a certified drawing. Sizes 80, 90 Port plates ,5 104, ,2 57,2 27,8 57, ,5 27, M 12; 17 deep M 12; 17 deep , Service line ports SE 1, Service line ports SE Detail Y , , M 12; 17 deep 27,8 Y, Service line ports SE 1 19 (see page 28) rueninghaus Hydromatik 17/28

18 efore finalising your design, please request a certified drawing. Unit Dimensions, Sizes 107, 125 Dimensions brackets for size , see port plates R ø160 h , ,5 2 ø1, Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 18x1,5 Shaft ends Sizes 107, 125 Size 107 Splined shaft Z Splined shaft W 45x2x30x21x9g W 40x2x30x18x9g DIN 5480 DIN 5480 Sizes 107, 125 Size 107 Parallel shaft with P Parallel shaft with key S 14x9x63 key S 12x8x63 DIN 6885 DIN R2,5 28 R2,5 E1x0,2 DIN 9 E1x0,2 DIN 9 M 16 8 ø39,6 M Y ø34,6 48,5 ø45 k6 M ,5 80 ø44,6 43 ø40 k6 M ø39,6 2,5 = 400 bar prepared for speed sensing control (D), with port M (inductive impulse detector ID see RE 938 hall effect speed sensor HD see RE 942, to be ordered separately!) with built-on flushing and boost valve (7) 82,8 M M 18 x 1, Detail Y 98 18/28 rueninghaus Hydromatik

19 efore finalising your design, please request a certified drawing. Sizes 107, 125 Port plates Dimensions brackets for size , ,7 66,7 31,8 66,7(57,2) 32(25) ,8(27,8) , M 14; 19 deep M14; 19 deep (M12; 17 deep) , Service line ports SE 1 1 / 4, Service line ports SE 1 1 / 4 (SE 1) Detail Y , Y M 14; 19 deep 31,8, Service line ports SE 1 1 / 4 19 (see page 28) rueninghaus Hydromatik 19/28

20 efore finalising your design, please request a certified drawing. Unit Dimensions, Sizes 160, ,5 see port plates R ø180 h6 95, ,5 77, , ,2 2 ø180, Service line ports (see port plates) 1, 2 Drain ports (1 port plugged) M 22x1,5 Shaft ends Sizes 160, 180 Size 160 Splined shaft Z Splined shaft W x2x30x24x9g W 45x2x30x21x9g DIN 5480 DIN 5480 Sizes 160, 180 Size 160 Parallel shaft with P Parallel shaft with key S 14x9x70 key S 14x9x70 DIN 6885 DIN R4 36 R2,5 R2,5 R2,5 M ø44,6 with built-on flushing and boost valve (7) 315 Y 201 M = 400 bar prepared for speed sensing control (D), with port M (inductive impulse detector ID see RE 938 hall effect speed sensor HD see RE 942, to be ordered separately!) 93 M M 18 x 1, ø39,6 53,5 ø k6 M ,5 ø45 k6 M 16 Detail Y 98 20/28 rueninghaus Hydromatik

21 RE 91001/01.97 efore finalising your design, please request a certified drawing. Sizes 160, 180 Port plates ,7 66,7 31,8 66, , M 14; 19 deep M 14; 19 deep , Service line ports SE 1 1 / 4, Service line ports SE 1 1 / Detail Y , , M 14; 19 deep 31,8 Y, Service line ports SE 1 1 / 4 19 (see page 28) rueninghaus Hydromatik 21/28

22 RE 91001/01.97 efore finalising your design, please request a certified drawing. Unit Dimensions, Size 200-0,029 ø , ,7 66, Shaft ends Splined shaft W x2x30x24x9g DIN 5480 M 16 Parallel shaft with key S 14x9x70 DIN R4 55 R2,5 ø44,6, Service line ports SE 1 1 / 4 Drain port (1 port plugged) M 22x1, ,8 M 14; 19 tief deep 53,5 k6 ø M Preferred types, please state type and ident-no. when ordering ype Ident-No. ype Ident-No. 2F5W FM10/61W-P FM10/61W-P FM12/61W-P FM12/61W-P FM16/61W-P FM16/61W-P FM23/61W-P FM23/61W-P FM23/61W-P FM23/61W-P FM23/61W-P FM23/61W-P FM28/61W-P FM28/61W-P FM28/61W-P FM28/61W-P FM28/61W-P FM28/61W-P FM32/61W-P FM32/61W-P FM32/61W-P FM32/61W-P FM32/61W-P FM32/61W-P FM45/61W-PZ FM45/61W-PZ FM45/61W-PZ FM56/61W-P FM56/61W-P FM56/61W-P FM56/61W-P FM56/61W-P FM56/61W-P FM63/61W-P FM63/61W-P FM63/61W-P FM63/61W-P FM63/61W-P FM63/61W-P /28 rueninghaus Hydromatik 2FM80/61W-P FM80/61W-P FM80/61W-P FM80/61W-P FM90/61W-P FM90/61W-P FM90/61W-P FM90/61W-P FM107/61W-P FM107/61W-P FM107/61W-P FM107/61W-P FM125/61W-P FM125/61W-P FM125/61W-P FM125/61W-P FM160/61W-P FM160/61W-P FM160/61W-P FM160/61W-P FM180/61W-P FM180/61W-P FM180/61W-P FM180/61W-P FM200/63W-P FM2/60W-VZ FM2/60W-VP FM2/60W-VZ FM2/60W-VP FM355/60W-VZH FM355/60W-VPH FM0/60W-VZH FM0/60W-VPH FLM710/60W-VZH FLM710/60W-VPH FM1000/60W-VZH FM1000/60W-VPH sizes : production plant Elchingen sizes : production plant Horb

23 efore finalising your design, please request a certified drawing. Unit Dimensions, Size 2 Port plate U Detail X 66,7 66,7 ø224h ,8 210 M14; 19 deep X Port plate 02 U 267 Detail X 236 with built-on flushing and boost valve (7) 105 Shaft ends Z Splined shaft P Parallel shaft with W x2x30x24x9g key S 14x9x80 DIN 5480 DIN R2,5 R1,6 M 16 ø45 53,5 ø k6 M ,7 32 X , Service line ports SE 1 1 / 4 Drain port (1 port plugged) M 22x1,5 U Port for bearing flushing (plugged) M14x1, rueninghaus Hydromatik 23/28

24 , efore finalising your design, please request a certified drawing. Unit Dimensions, Size ,5 U ø280 h X Detail X 36,6 36,6, Service line ports SE 1 1 / 2 Drain port (1 port plugged) M 33x2 U Port for bearing flushing (plugged) M 14x1,5 M16; 21 deep Shaft ends Z Splined shaft P Parallel shaft with W 60x2x30x28x9g key S 18x11x100 DIN 5480 DIN R1,6 R4 M 20 ø55 64,4 ø60 m6 M /28 rueninghaus Hydromatik

25 RE 91001/01.97 efore finalising your design, please request a certified drawing. Unit Dimensions, Size ,5 U 361, Detail X, Service line ports SE 1 1 / 2 Drain port (1 port plugged) M 33x2 U Port for bearing flushing (plugged) M 18x1,5 Shaft ends Z Splined shaft P Parallel shaft with W 70x3x30x22x9g key S 20x12x100 DIN 5480 DIN R1,6 R4 M 20 ø62,7 74,5 74,4 ø70 m6 M ø ,5 h X 36,6 36,6 79,4 270 M16; 21 deep rueninghaus Hydromatik 25/28

26 efore finalising your design, please request a certified drawing. Unit Dimensions, Size ,5 U ø400 h X Detail X 44,5 44,5, Service line ports SE 2 Drain port (1 port plugged) M 42x2 U Port for bearing flushing (plugged) M18x1,5 96,8 340 M20; 30 deep Shaft ends Z Splined shaft P Parallel shaft with W 90x3x30x28x9g key S 25x14x125 DIN 5480 DIN 6885 R1,6 R4 M 24 ø82,6 95 ø90 m6 M /28 rueninghaus Hydromatik

27 efore finalising your design, please request a certified drawing. Unit Dimensions, Size ,5 U Shaft ends Z Splined shaft P Parallel shaft with W 90x3x30x28x9g key S 25x14x125 DIN 5480 DIN 6885 R1,6 R4 M 24 ø82,6 95 ø90 m6 M 24 ø h X 512 Detail X 44,5 44,5, Service line ports SE 2 Drain port (1 port plugged) M 42x2 U Port for bearing flushing (plugged) M18x1,5 96,8 340 M20; 30 deep rueninghaus Hydromatik 27/28

28 RE 91001/01.97 efore finalising your design, please request a certified drawing. Port plate 19, with integrated pressure relief valves D2 D5 D1 Port plate 191 (pressure relief valves without pressure sequence range) D2 Port plate 192 (pressure relief valves with pressure sequence range) p St D3 D4 M M M M D7 D6 Z p St p St 2 Detail Y D10 M Y S 1 S 1 M S Y 1 S 1 D9 D12 D11 Detail Z D8 Pressure relief valves Pressure relief valves - without pressure sequence range (1) - with pressure sequence range (2) MHDN16 (Sizes ) MHD16 (Sizes ) MHDN22 (Sizes ) MHD22 (Sizes MHDN32 (Sizes ) MHD32 (Sizes ) D13 S 1 M M, Service line ports SE, 420 bar (6000 psi high pressure series) S 1 oosting p St Pilot pressure port G 1/4 M, M est ports (plugged) Size D1 D2 D3 D4 D5 D6 D7 D8 D9 D10 D11 D12 D13 Ports, Port S 1 Ports M,M ,8 23,8 19 M10; 17 deep SE 3 / 4 M 22x1,5 M 20x1, ,8 23,8 19 M10; 17 deep SE 3 / 4 M 22x1,5 M 20x1, ,8 23,8 19 M10; 17 deep SE 3 / 4 M 22x1,5 M 20x1, ,8 23,8 19 M10; 13 deep SE 3 / 4 M 26x1,5 M 26x1, ,8 23,8 19 M10; 13 deep SE 3 / 4 M 26x1,5 M 26x1, ,5 17, ,2 27,8 25 M12; 18 deep SE 1 M 26x1,5 M 26x1, ,5 17, ,2 27,8 25 M12; 18 deep SE 1 M 26x1,5 M 26x1, , ,7 31,8 32 M14; 19 deep SE 1 1 / 4 M 26x1,5 M 26x1, , ,7 31,8 32 M14; 19 deep SE 1 1 / 4 M 26x1,5 M 26x1, ,7 31,8 32 M14; 19 deep SE 1 1 / 4 M 26x1,5 M 30x1, ,7 31,8 32 M14; 19 deep SE 1 1 / 4 M 26x1,5 M 30x1,5 rueninghaus Hydromatik GmbH, Plant Elchingen, Glockeraustraße 2, D Elchingen, el. (07308) 820, elefax (07308) 7274 Plant Horb, n den Kelterwiesen 14, D Horb, el. (07451) 920, elefax (07451) /28 rueninghaus Hydromatik he specified data is for product description purposes only and may not be deemed to be guaranteed unless expressly confirmed in the contract. ll rights reserved Subject to revision