lindab industrial Single Wall Round Double Wall Round Flat Oval Comfort Silencer Industrial

Transcription

1 Single Wall Round Double Wall Round Flat Oval Comfort Silencer Industrial

2

3 Lindab Industrial Building without barriers Well-known for our gasketed system, Lindab s worldclass quality extends to our Industrial Ductwork Division. It is a natural addition for our skilled trades personnel and fabrication facilities. The ability to use spiral lockseam pipe construction, when the system requirements allow, results in using lighter gauge and delivers superior strength than long seam welded duct. Also, gore lock construction for fittings result in added strength against collapse due to the built-in stiffening rib. NFPA Standard 91 is widely used for duct systems conveying particulates and removing flammable vapors (including paint-spraying residue), and corrosive fumes. Duct conveying systems are generally classified from Class 1-5. Classification* Class 1 covers non-particulate applications, including makeup air, general ventilation, and gaseous emission control. Class 2 is imposed on moderately abrasive particulate in light concentration, such as that produced by buffing and polishing, woodworking, and grain handling. Class 3 consists of highly abrasive material in low concentration, such as that produced from abrasive cleaning, dryers and kilns, boiler breeching, and sand handling. Class 4 is composed of highly abrasive particulates in high concentration, including materials conveying high concentrations of particulates listed under Class 3. Class 5 covers corrosive applications such as acid fumes. * Information is excerpted from the 2012 ASHRAE handbook for Industrial Duct Construction.

4 Materials 4 Galvanized steel, uncoated carbon steel, or aluminum are most frequently used for industrial air handling. Lindab can also provide 304L and 316L stainless steel in a variety of finishes and aluminized steel for high temperature applications. Aluminum duct should not be used for conveying abrasive materials. When temperatures exceed 400 F (200 C) galvanized steel is not recommended. Please consult Lindab for technical assistance in selecting material for handling corrosive gases, vapors, or mists. Round Ducts Duct and fittings are available in sizes ranging from 3" diameter to 96" diameter and material thickness from 28 gauge through 10 gauge. Coordination Drawings Lindab has the in-house capability to generate detailed 3-D drawings to aid in the coordination of the fabrication and installation requirements. In addition, we can assist in manifolding and spooling sections of the ductwork at the factory to minimize field welding or bolted connections. spiral lockseam duct longitudinal-seam welded duct

5 Capabilities Lindab has the capability of producing spiral lockseam duct in diameters from 3" up to 80". Spiral duct can be provided from metal thicknesses ranging from 28 gauge to 16 gauge (galvanized steel) and 24 gauge to 20 gauge (stainless steel). Lindab spiral is certified by AMCA International for duct leakage. Longitudinal-seam welded duct products may be made in diameters as large as 96" and up to 10 gauge thicknesses. Manifolding and spooling options are also available. Our technicians are trained and accomplished in heavy duty sheet metal applications. In addition to economical stitch welds, tack and seal joints and continuous resistance welds, Lindab has extensive welding and lockforming capabilities in MIG, TIG and special finished welds. We have a number of transverse connection options besides our LindabSafe gasketed system, including traditional slip fit, flanged, Van Stone, swedged, LAP and butt joints. A wide range of materials are offered to satisfy your customer s requirements. Each have a specific purpose in the field: galvanized steel black iron paint-grip galvanized powder coat and PVC-coated steel antimicrobial coatings T3003 aluminum 304L and 316L stainless steel aluminized steel 5 Availability Standard Diameters, Thicknesses and Materials Lindab Industrial products are built to your specifications. Industrial round fittings can be manufacturered as small as 3 diameter and as large as 96 diameter. The same custom materials available for duct are offered in fittings. Fittings can be delivered loose or manifolded. Below is a quick reference guide to Lindab s capabilities. For projects outside of these parameters, please consult Lindab for special assistance.

6 About the charts 6 1. Cells displaying a stiffener type and size represent a stiffening scheme based on 12 ft spacing between stiffeners or flanges. 2. The plus symbol (+) represents a stiffening scheme based on a 6 ft spacing between stiffeners. 3. The stiffener size listed is the lightest angle ring that meets the reinforcement requirements for negative pressure. 4. Transverse joint designed for flanges and bolt requirements are in addition to those for negative pressure. Consult Lindab for design assistance. 5. The number of welds listed for stiffeners is the total number of stitch welds required around the circumference of the flange. The welds are to be staggered, both toe and heel of the ring, approximately half of the required stitch welds go in front (toe) and the other half in back (heel). 6. Consult Lindab for your specific design requirements.

7 Class 1 - Stiffiner/Weld Schedule -2 to -30 in. wg Spiral-Carbon & Galv Negative Pressure, in wg 2 6 Diameter, in. Gauge Stiffiner Size/Type No./Size of Welds Gauge Stiffiner Size/Type No./Size of Welds 4 thru Unstiffined 22 Unstiffined Unstiffined 20 Unstiffined Unstiffined 18 Unstiffined Unstiffined 18 Unstiffined Unstiffined 18 Unstiffined Unstiffined 16 Unstiffined Unstiffined 20 L / Unstiffined 20 L 1 1 / Unstiffined 20 L 1 1 / L / L 1 1 / L 1 1 / L / L 1 1 / L / L 1 1 / L / L 1 1 / L / L / L L / L / L / L / L / L Negative Pressure, in wg Diameter, in. Gauge Stiffiner Size/Type No./Size of Welds Gauge Stiffiner Size/Type No./Size of Welds 4 thru Unstiffined 22* Unstiffined Unstiffined 18 Unstiffined 14 thru Unstiffined 16 Unstiffined Unstiffined 18 L / Unstiffined 18 L / L / L 1 1 / L / L 1 1 / L 1 1 / L 1 1 / L 1 1 / L 1 1 / L / L / L / L / L / L / L / L / * 10 diameter = 20 gauge + 6-foot intervals (otherwise 12-foot intervals) Consult Lindab

8 Spiral-Carbon & Galv Class 2 - Stiffiner/Weld Schedule -2 to -30 in. wg 8 Negative Pressure, in wg 2 6 Diameter, in. Gauge Stiffiner Size/Type No./Size of Welds Gauge Stiffiner Size/Type No./Size of Welds 4 thru Unstiffined 22 Unstiffined Unstiffined 20 Unstiffined Unstiffined 20 Unstiffined Unstiffined 18 Unstiffined Unstiffined 18 Unstiffined Unstiffined 18 Unstiffined Unstiffined 16 Unstiffined Unstiffined 16 Unstiffined Unstiffined 18 L / Unstiffined 18 L 1 1 / L / L 1 1 / L / L 1 1 / L 1 1 / L / L 1 1 / L / L 1 1 / L / L 1 1 / L / L / L L / L / L / L / L / L Negative Pressure, in wg Diameter, in. Gauge Stiffiner Size/Type No./Size of Welds Gauge Stiffiner Size/Type No./Size of Welds 4 thru 8 22 Unstiffined 22* Unstiffined Unstiffined 18 Unstiffined 12 thru Unstiffined 16 Unstiffined Unstiffined 16 L / Unstiffined 16 L / L / L / L / L 1 1 / L / L 1 1 / L 1 1 / L 1 1 / L 1 1 / L 1 1 / L / L / L / L / * 8 Diameter is 20 Gauge + 6-foot intervals (otherwise 12-foot intervals) Consult Lindab

9 Class 5 - Stiffiner/Weld Schedule -2 to -30 in. wg Spiral-Stainless Steel Negative Pressure, in wg 2 6 Diameter, in. Gauge Stiffiner Size/Type No./Size of Welds Gauge Stiffiner Size/Type No./Size of Welds 4 thru Unstiffined 22 Unstiffined Unstiffined 20 Unstiffined Unstiffined 18 Unstiffined Unstiffined 18 Unstiffined Unstiffined 18 Unstiffined Unstiffined 16 Unstiffined Unstiffined 20 L / Unstiffined 20 L 1 1 / Unstiffined 18 L 1 1 / L / L 1 1 / L 1 1 / L / L 1 1 / L / L 1 1 / L / L 1 1 / L / L / L L / L / L / L / L / L Negative Pressure, in wg Diameter, in. Gauge Stiffiner Size/Type No./Size of Welds Gauge Stiffiner Size/Type No./Size of Welds 4 thru Unstiffined 22* Unstiffined Unstiffined 18 Unstiffined 14 thru Unstiffined 16 Unstiffined Unstiffined 18 L / Unstiffined 18 L / L / L / L / L 1 1 / L 1 1 / L 1 1 / L 1 1 / L 1 1 / L / L / L / L / L / L / L / L / * 10 Diameter is 20 Gauge + 6-foot intervals (otherwise 12-foot intervals) Consult Lindab

10 End Treatments TC1 * Std Flange Connection: Inside of duct Std Angle Ring Connection: Outside of duct 10 TC2 ** TC3 *** TC4 ** TC5 TC6 * Add 3" plus flange thickness for each end on fittings; ** Not used in spiral duct; *** When used with spiral duct a vanstone flange coupling is factory installed.

11 Flanges & Angle Rings Lindab has partnered with angle ring and flange manufacturer s across the country to bring you reliable connections for your heavy-duty applications. 11 Standard Pressed Black Iron Galvanized (hot dipped) Aluminum Stainless Steel Standard Rolled Galvanized Stainless Steel Aluminum With or Without holes Leg-in or Leg-out Precise measurements to ensure an easy and tight fit Bolt Hole Options K Pattern (standard) H Pattern Special patterns available upon request

12 12 Lindab Transfer Table of contents Model Page Model Page Duct... SRTR ORINGTR TLTR1 TLTR2 Elbows... BTR BSTR BSFTR Reducers... RCLTR RRTR Branches... TVTR XVTR YVTR Taps PSTR PSVTR Take-offs ILTR ILRTR End caps EPTR Couplings OUTR MFK Clamps MFTR SB SB-1

13 Ductwork for dust and other fine particulate collection. Transfer components are joined easily with a gasketed tension clamp. It s disassembled just as easily! Cleaning and inspection is simple with Lindab Transfer. In fact, these parts can be relocated and reused if necessary. Dimensions of duct and fittings 13 The duct system is suitable for: Particle transportation from woodworking, such as saw mills, carpenters, furniture manufacturers and craft work shops Comfort ventilation Extraction systems for better working environment Plasma cutters Specially designed ventilation plants where you have extra demands for form, color and appearance. Ød nom Ød v in in in Angle tolerance 2

14 Transfer SRTR/ORINGTR 14 Round spiral with Transfer connection on each end. Oring used in sealing option for TLTR components Available in diameters 3" - 20" Available in lengths 12" - 120" Dimension Ød SRTR 8 Dimension Ød ORINGTR 8

15 Transfer TLTR1/TLTR2 15 Used together with the telescopic duct TLTR2 to adjust duct length. Airflow direction travels from TLTR1 towards TLTR2. The maximum extension will be marked on exterior of each TLTR1. Used together with the telescopic duct TLTR1 to adjust duct length. Can also be used as ordingary duct. Seal joint after assembly by using 1) mastic tape or 2) SB + ORINGTR. Dimension Ød TLTR1 8 Dimension Ød 1 TLTR2 8 Ød 3 nom t I 1, I 2 I 3 I min I max in in in in in in

16 Transfer BTR 16 BTR 90 Pressed and seam welded elbow with a Transfer connection on each end. Available angles: 90, 60, 45, 30 available diameters: 3" - 12" Ød nom Length (L) by angle of bend in Angle of bend Dimension Ød BTR 90 8 Ød nom Radius (r m ) by angle of bend in

17 Transfer BSTR 17 BSTR 90 Pressed and seam welded elbow with a Transfer connection on each end. Available angles: 90, 60, 45, 30 available diameters: 4-12 Ød nom Length (L) by angle of bend in Angle of bend Dimension Ød BSTR 90 8 Ød nom Radius (r m ) by angle of bend in

18 Transfer BSFTR 18 Segmented elbow with a Transfer connection on each end. available diameters: 14" - 20" r m 1.5 x Ød Dimensions Ød nom Length (L) by angle of bend in Angle of bend Dimension Ød BSFTR 90 16

19 Transfer RCLTR Long, fabricated concentric reducer with a Transfer connection on each end. Dimension Ød 1 Dimension Ød 2 RCLTR 8 6 Ød nom Ød 2 nom L in in in

20 Transfer RRTTR 20 Transistion from round Lindab Transfer to rectangular connection. The measures e and h only need to be specified for alternative 6. A negative value for e, for example, means that e is outside dimension a. Available in Ød diameters 3-20 Dimension Ød Dimension a x b RRTTR 8 18 x 12

21 Transfer YVTR 21 Dimensions 30 Y-piece The adjacent table only contains a limited selection of 30 laterals where all dimensions d 1, d 3 and d 4 are equal in size. Other dimensions are available upon request. Ød 1 nom Ød 3 nom Ød 4 nom I 3 I 4 in in in in YVTR Dimension Ød 1 Dimension Ød 3 Dimension Ød 4

22 Transfer TVTR 22 Dimensions 30 lateral tee. The adjacent table only contains a limited selection of 30 laterals where all dimensions d 1, d 2 and d 3 are equal in size. Other dimensions are available upon request. In all combinations, the installation length l 1 is only governed by the branch diameter d 3. For example, all Tee-pieces with d 3 = 8" have installation length l 1 = 24". Ød 1 nom Ød 2 nom Ød 3 nom I 1 I 3 I 4 in in in in in in TVTR Dimension Ød 1 Dimension Ød 2 Dimension Ød 2

23 Transfer XVTR 23 Dimensions 30 crossing lateral tee. The adjacent table only contains a limited selection of 30 laterals where all dimensions d 1, d 2 and d 3 /d 4 are equal in size. Other dimensions are available upon request. In all combinations, the installation length l 1 is only governed by the larger branch diameter d 3 /d 4. For example, all crosspieces with d 3 = 6" and d 4 = 8" have installation length l 1 = 24". Ød 1 nom Ød 2 nom Ød nom 3 Ød 4 nom I 1 I 3 I 4 in in in in in in XVTR Dimension Ød 1 Dimension Ød 2 Dimension Ød 3 Dimension Ød 4

24 Transfer PSTR 24 Saddle tap. The saddle is fixed with two sealing clamps MFK (page 23). Most sizes Ød 3 3"-16" are pressed. Fabricated options indicated in chart below. Fabricated Sizes Ød 3 ØD Dimensions H = X + 0.5(ØD) X-dimensions in the chart below: X Dimensions Ød 3 nom Pressed X Fabricated X in in in n/a n/a n/a n/a n/a n/a n/a 14 n/a n/a 18 n/a n/a 3.0 Dimension ØD Dimension Ød 3 PSTR 8 6

25 Transfer PSVTR 25 Dimensions 30 Lateral saddle tap. The saddle is fixed with two sealing clamps MFK (page 26). This product should not be installed with screws or blind rivets when used in chip extraction installations. The adjacent table only contains a limited selection of 30 lateral saddle taps where all dimensions d and d 3 are equal in size. Other dimensions are available upon request. Ød 3 nom L I 3 I 4 in in in in Dimension ØD Dimension Ød 3 PSVTR 8 6

26 Transfer ILTR/ILRTR 26 Take-off Bellmouth take-off Available in diameters 3" - 20" Available in diameters 4" - 16" Ød 3 nom L Ød 3 nom L in in in in " - " ILTR 8 Dimension Ød 1 ILRTR 8 Dimension Ød 1

27 Transfer EPTR/OUTR 27 End cover Available in diameters 3-20 Ød 1 nom L in in Coupling between Transfer and Safe systems. Available in diameters 3" - 20" Lengths 3" diameter = 2.25" 4" - 20" diameter = 2" Dimension Ød EPTR 8 Dimension Ød 1 OUTR 8 6 Dimension Ød 2

28 Transfer MFTR/MFK 28 Coupling with female end between Transfer and Safe systems. Available in diameters 3" - 20" Ød 1 nom L in in The inside of the sealing clamp is clad with EPDM rubber gasket. Used for attaching slide-on stub saddle PSTR and PSVTR (page 20-21). Available in diameters 3" - 20" Dimension ØD MFTR 8 Dimension ØD MFK 8

29 Transfer SB/SB-1 29 The barrel clamp used for connecting Lindab Transfer is provided with a rubber gasket. The clamp handles can be secured against inadvertent opening by means of a lock pin. Temperature range Available in diameters 3" - 20" -22 to +167 F continuous -40 to +185 F intermittent The barrel clamp used for connecting Lindab Transfer is provided with a rubber gasket. Provided with a rubber gasket of EPDM rubber and a thread spring. The clip handle can be secured against inadvertent opening by means of a lock pin. Temperature range -22 to +167 F continuous -40 to +185 F intermittent Available in diameters 3" - 20" Ø Dia b 3" - 6" ½" 7" - 10" ¾" 12" - 20" 1" Ø Dia b 3" - 6" ½" 7" - 10" ¾" 12" - 20" 1" Dimension Ød SB 8 Dimension Ød SB-1 8

30 Notes

31

32 Lindab in brief... Lindab is an international company which develops, manufactures, and markets sheet metal products and system solutions for air distribution. With over 50 years in history, Lindab has continued to prove its place in the HVAC industry. Lindab is a yellow label union manufacturer and a proud partner of the Sheet Metal Worker s International Association (SMWIA). Lindab, Inc. is headquartered in Portsmouth, Virginia. REV Lindab, Inc Airline Boulevard Portsmouth, Virginia Phone: Fax: