Steel Fabricated Coupling

Transcription

1 Steel Fabricated Coupling Straight Connection IMPORTANT LINKS Click appropriate words to go to: Standard Limited Warranty Sales Terms & Conditions Freight Policy Returns Policy Corrosion & Product Selection Notice Description: A bolted sleeve type coupling for joining plain end pipe of the same diameters. Application: Joining plain end pipe without the need for welding or special pipe fittings. Key Features: Meets applicable AWWA C219 Standards Allows for limited expansion and contraction Will dampen vibration to reduce pipe fatigue Easy to install, no special pipe end preparation required Available in a wide variety of pipe O.D. sizes and sleeve lengths Most sizes will accommodate anchor studs to restrain the joints Can be custom made to fit odd O.D.s or other unusual applications Provided with or without pipe stops to accommodate customer needs Has good deflection capabilities, allows change in piping direction without the need of elbows, bends Steel sizes built to specific O.D. and Ductile Iron sizes are built with range to accommodate the variances in Ductile Iron pipe O.D.s Materials Specifications (subject to change): SLEEVE: ASTM A, ASTM A or Carbon Steel having minimum yield of 0,000 PSI FOLLOWERS: Ductile Iron ASTM A, Steel AISI C, or A1 Grade 0 HSLA Steel. Designed for a high strength-to-weight ratio. Follower thickness determined by coupling size & NUTS: High strength, low alloy Steel with heavy semi-finished hexagon nuts Optional: Stainless Steel and Carbon Steel ASTM A0 electro-galvanized with di-chromate seal GASKET: Nitrile (Buna N) NSF 1 compounded to produce superior storage and performance characteristics while resisting water, acids, alkalies, most (aliphatic) hydrocarbon fluids, and other chemicals Temperature Range: - F to 10 F FINISH: Flexi-Coat Fusion Bonded Epoxy Finish Working Pressure: Up to 10 PSI Pipe Applications: All Types. HDPE requires use of stiffeners. Contact Smith-Blair Engineering for any questions. THIS PRODUCT DOES NOT RESTRAIN PIPE MOVEMENT. Proper anchoring is required to prevent pipe pullout. Failure to anchor or improper anchoring can result in dangerous pipe content escape, property damage, serious injury, or death. Read the product installation instructions prior to installing this product. Sizes (in inches): ½, ¾, 1, 1¼, 1½, 2, 2½,, -,, -,,,,, -,,, 1,,, 0,, 2,,. NOTE: Larger sizes available upon request. 9

2 Steel Fabricated Coupling Straight Connection Total Angular Deflection Per Joint FOR RANGES SLEEVE LENGTH MM " MM " 1MM " 20MM 0. thru thru 0. º º º 2.0 thru 1.0. thru 2.9 º ½º ½º 1.0 thru.00. thru 2½º º ½º. thru.00 thru 9 2º ½º º. thru thru - º ½º 2. thru thru 1-2½º º 0. thru thru ½º 0. thru 0.00 thru º Standard Lengths for Steel Sizes NOM. PIPE SIZE IN. BUNA-N GASKET SLEEVE THK. X LGTH. IN. (A) (B) (D) NO. DIA. IN. LGTH. IN. (L) 1/ /2 2 1/2 2 1/ / /2 / 2 1/2 2 1/ / 2 1/2 1/ 1 1/ / 2 1/2 1 1/ / 2 1/2 1/ / 2 1/2 1/ / 2 1/2 / / 2 1/ / 1/ / 1/2 9 1/2 2 1/ /2 / / / /0 1/ /0 1/ /0 1/2 1/2 1/ / 1/2 1 1/ / / 1 1/2 1/ / / 1/ / 1/2 2 1/ / 1 1/2 1 1/2 Standard Length Sleeves 1/2" thru " Steel Pipe Sizes. + Indicates couplings furnished with Steel Z" section, High Strength Follower Flanges. pipe movement could cause the pipe to move out of the coupling. NOTE: Couplings working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. ConsultSmith-Blair regarding your specific coupling pressure requirements. 10

3 Couplings Standard Lengths for Steel Sizes, Continued NOM. PIPE SIZE IN. BUNA-N GASKET SLEEVE THK. X LGTH. IN. (A) (B) (D) NO. DIA. IN. LGTH. IN. (L) /2 22 / / /2 1/2 1/ / / /2 1/ / / 1/ / 1 1/ / / / /9 1/ / / 1/ / 1 1/ / / / /9 1/ / / 1/ / 1/ / 1 1/ / 1/ / 1/ / 1/ / 1/ / 1/ / 1/ / 1/ / 1 1/ / 1/ / 1/ / 1 1/ / 1 1/2 1 Standard Length Sleeves 1/2" thru " Steel Pipe Sizes + Indicates couplings furnished with Steel Z" section, High Strength Follower Flanges. pipe movement could cause the pipe to move out of the coupling. NOTE: Couplings working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. ConsultSmith-Blair regarding your specific coupling pressure requirements. Standard Length Sleeves " thru " Steel Pipe Sizes pipe movement could cause the pipe to move out of the coupling. NOTE: Couplings working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. 11

4 Couplings Standard Lengths for Steel Sizes, Continued NOM. PIPE SIZE IN. BUNA-N GASKET SLEEVE THK. X LGTH. IN. (A) (B) (D) NO. DIA. IN. LGTH. IN. (L) / 1/ / 1/ / 1 1/ / 1 1/ / 1/ / 1/ / 1 1/ / 1 1/2 1 Standard Length Sleeves " thru " Steel Pipe Sizes pipe movement could cause the pipe to move out of the coupling. NOTE: Couplings working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. Standard Lengths for Ductile Iron and Cast Iron Sizes NOM. PIPE SIZE IN. PIPE O.D. SLEEVE THK. X LGTH. IN. OVERALL DIA. (D) (A) (B) NO. DIA. IN. LGTH. IN. (L) APPROX. SHIP WT. LBS /./ 2 2 1/2 1 1/ / /./ / 1/ 1/2 1 1/ /2 / /2 / /2 19/ /2 9 / / 9/ / 9/ / / / 1/ /2 1 2/ / 1 1/ / 1 1/ Standard and Long Length Sleeves " thru " CAST IRON The basic design of bolted compression couplings does not provide for anchoring the pipes against pull-out. Suitable anchorage must be provided when excessive pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. ***The last three numbers of the catalog number indicate the type of gasket. (Buna N) gaskets are furnished as standard. BUNA-N-00, BUNA-N Protected -01 (with brass spring molded into leading edge) 12

5 Couplings Standard Lengths for Ductile Iron and Cast Iron Sizes, Continued NOM. PIPE SIZE IN. PIPE O.D. SLEEVE THK. X LGTH. IN. OVERALL DIA. (D) (A) (B) NO. DIA. IN. LGTH. IN. (L) APPROX. SHIP WT. LBS / 1 / / 1 1/ / 19 / 19 / 19 / / / / / / 21 1/ 21 1/ 21 1/ / 1/ 1/ 1/ /2 1/2 1/2 1/ / 2 1/ 2 1/ 2 1/ / 0 / 0 / 0 / Standard and Long Length Sleeves " thru " CAST IRON The basic design of bolted compression couplings does not provide for anchoring the pipes against pull-out. Suitable anchorage must be provided when excessive pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. ***The last three numbers of the catalog number indicate the type of gasket. (Buna N) gaskets are furnished as standard. BUNA-N-00, BUNA-N Protected -01 (with brass spring molded into leading edge) 1

6 Couplings Large Diameter Standard Lengths NOM. PIPE SIZE IN. SLEEVE THK. X LGTH (A) (B) FOLLOWER FLANGE O.D. NO. DIA. X LGTH (L) CATALOG NUMBER 1/ x / x / x / x x / x x / x /2 x / x / x 1/ x / x 1/ x x 1/ x x 1/ x /2 x 1/ x / x / x / x / x x / x x / x /2 x / x / x / x / x / x x / x x / x /2 x / x / x / x / x / x x / x x / x /2 x / x / x 0 / x / x 0 / x x 0 / x x 0 / x /2 x 0 / x / x 0 1/ x / x 0 1/ x x 0 1/ x x 0 1/ x /2 x 0 1/ x / x 1 1/ x / x 1 1/ x x 1 1/ x x 1 1/ x /2 x 1 1/ x The basic design of bolted compression couplings does not provide for anchoring the pipes against pullout. Suitable anchorage must be provided when excessive pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressure depends on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. 1

7 Couplings Large Diameter Standard Lengths Continued NOM. PIPE SIZE IN. SLEEVE THK. X LGTH (A) (B) FOLLOWER FLANGE O.D. NO. DIA. X LGTH (L) CATALOG NUMBER 1/ x 2 1/2 x / x 2 1/2 x x 2 1/2 x x 2 1/2 x /2 x 2 1/2 x The basic design of bolted compression couplings does not provide for anchoring the pipes against pullout. Suitable anchorage must be provided when excessive pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressure depends on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. For Large Diameter Steel and Cast Iron Sizes Standard Lengths NOM. PIPE SIZE IN. PIPE O.D. SLEEVE THK. X LGTH (A) (B) FOLLOWER NO. DIA. X LGTH (L) CATALOG NUMBER WEIGHT LBS. 1/ x 2 / x / x 2 / x x 2 / x x 2 / x /2 x 2 / x / x 1/2 1 x / x 1/2 1 x x 1/2 1 x x 1/2 1 x /2 x 1/2 1 x / x 1 x / x 1 x x 1 x x 1 x /2 x 1 x / x 1/ 1 x / x 1/ 1 x x 1/ 1 x x 1/ 1 x /2 x 1/ 1 x / x / 1 x / x / 1 x x / 1 x x / 1 x /2 x / 1 x / x 9 1 x / x 9 1 x x 9 1 x x 9 1 x /2 x 9 1 x The basic design of bolted compression couplings does not provide for anchoring the pipes against pullout. Suitable anchorage must be provided when excessive pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressure depends on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. 1

8 Couplings For Large Diameter Steel and Cast Iron Sizes Standard Lengths, Continued NOM. PIPE SIZE IN. PIPE O.D. SLEEVE THK. X LGTH (A) (B) FOLLOWER NO. DIA. X LGTH (L) CATALOG NUMBER WEIGHT LBS. 1/ x 2 1/2 x / x 2 1/2 x x 2 1/2 x x 2 1/2 x /2 x 2 1/2 x / x 1/ x / x 1/ x x 1/ x x 1/ x /2 x 1/ x / x x / x x x x x x /2 x x / x / x / x / x x / x x / x /2 x / x / x 1 19/2 x / x 1 19/2 x x 1 19/2 x x 1 19/2 x /2 x 1 19/2 x The basic design of bolted compression couplings does not provide for anchoring the pipes against pullout. Suitable anchorage must be provided when excessive pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressure depends on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. 1

9 Couplings Long Lengths ½" through " Steel Pipe NOM. PIPE SIZE IN. PIPE OD BUNA-N GASKET SLEEVE THK. X LGTH. IN. (A) (B) (D) NO. DIA. IN. LGTH. IN. (L) APPROX. SHIP WT. LBS. 1/ /2 / / 2 1/2 1/ /2 2 1/2 1/2 1 1/ / 2 1/2 1 1/ / 2 1/2 1/ / / 2 1/2 1 1/ / / /2 1/ / / / /2 1/ / 9 / 2 1/ /2 1/ / /2 1 1/ / / 2 1/ / 1/ 2 1/ / 1 / 2 1/ / / 2 1/ / 22 / 2 1/ / / 2 1/ / 2 / 2 1/ / 2 / 2 1/ Indicates couplings furnished with Steel Z" section, High Strength Follower Flanges. pipe movement could cause the pipe to move out of the coupling. NOTE: Coupling working pressures depend on many variables such as pipe type, pipe diameter, sleeve thickness, sleeve material, gasket cross section, follower type and number of bolts. Consult Smith-Blair regarding your specific coupling pressure requirements. 1