TOTAL AIRTOOL SERVICES (UK) Ltd
|
|
- Ferdinand Summers
- 5 years ago
- Views:
Transcription
1 TOTAL AIRTOOL SERVICES (UK) Ltd BALANCER OPERATING MANUAL Reproduced from Tecna manual
2 Translation of the Original Instructions Install the balancer before using it. This operation is to be carried out by skilled personnel who must comply with the directions outlined in this manual: a wrong installation could cause injury/damage to people/property. This manual contains important information that the user must adhere to in order to use the balancer safely. Be sure to have clearly understood all the instructions before using the balancer. Failure to do so could cause injury. The balancer was built in conformity with European Community Directives that were pertinent and applicable when the balancer was put on the market and that entail the CE marking of the product. Intended conditions of use The balancers are designed to balance the weight of tools and utensils in general and are to be used by one operator at a time. The balancer may be used in an assembly line, in single workplaces, in professional or private environments, as a hobby, etc. Always operate, inspect and maintain this balancer in perfect working order in accordance with all regulations pertinent to balancers, tools and workplaces. Use contraindications Do not use the balancer in environments with potentially explosive atmospheres. Do not permit children or people under age to use the balancer. Do not work, transit or linger underneath the balancer. When using balancers, always fully and duly comply with the standards and laws in force in the country in which they are used. TECNA S.p.A. will not be held liable for any damage or problems caused by customers using these balancers for any other application. Choosing the balancer Assess the total load to be balanced: tool, accessories and sections of hoses or cables to be lifted by the balancer. The overall load to be balanced must fall within the balancer s minimum and maximum load-bearing capacity. Starting up the balancer Assess the range of the work area and, if need be, hang the balancer on a carriage to be able to use it properly in an area wide enough to carry out the required activities. If screw-fixing devices are used to install the balancer, use self-locking nuts, split-pins or other safety systems. Always connect the safety suspension S, using exclusively the supplied standard fittings (Fig.1), to a suitably sized support. The safety support MUST NOT BE the same one used for the main suspension 17 (Fig.1). If the main suspension breaks, the max falling distance must not be more than 100 mm. Tighten the nuts of the clamps (Fig.1) at a torque of 4 Nm. To avoid anomalous wear, the load must be applied vertically and in any case the cable must be free to line up with the direction of the load. Using the balancer Grip the tool hanging from the balancer and carry out the required operations. Then accompany the tool until it balances, on the vertical line of the balancer, and release it. The load to be balanced must be hung on snap-hook 31 (Fig.5). Ensure that the snap-hook is properly closed after having hung the load. The cable must never be unwound all the way: its work travel must end at least 100 mm before it reaches the lower limit (balancers are fitted with an automatic limit stop system). If need be, move and lock the clamp M (Fig.5) to stop the upward stroke.
3 Do not unhook the load if the clamp M (Fig. 5) does not lean onto the rope s swaging (POSITION SHOWN IN FIGURE 5). When using the balancer, always don individual protective gear and closely adhere to the prevailing accident prevention regulations. It is strictly prohibited to: - Abandon the load if it is not in a vertical position - Swing/throw the hanging load to another operator - Move the load by pulling the balancer s cable - Hang loads that are not within the upper and lower ranges of the admissible load-bearing capacity - Hang more than one tool on the balancer The sole risk linked to the use of the balancer consists in any uncontrolled rewinding of the cable. This very dangerous event will be avoided by adhering to the following instructions: - if you have any doubts concerning the working efficiency of the balancer, BEFORE performing any kind of inspection be sure to hold up the hanging tool to prevent it from falling and DISCHARGE THE SPRING COMPLETELY Should one wish to fully discharge the spring, stop the discharging operation as soon as the spring is effectively and completely discharged (proceeding beyond this position would damage the spring which would require to be replaced). - if for any reason whatsoever the balancer does not rewind the cable, DO NOT do anything on your own initiative but contact the customer service at once - never release the load if the cable has not been fully wound in the drum - if the balancer s cable is unwound and no load applied to it, DO NOT do anything on your own initiative but contact customer service at once Adjusting the balancer To enable the balancer to balance heavier loads, use the specific key to turn screw 45 (Fig. 5) in the direction indicated by symbol +. For lighter loads, turn screw 45 (Fig. 5) in the direction indicated by symbol -. After having adjusted the load, check that the cable slides freely for its entire length: the movement must not be restricted when the spring has wound all the way. Check the stroke often and at different speeds. NOTE: should the balancer s capacity of supporting a hanging load decrease, this could mean that the spring of the drum is about to break. DO NOT MODIFY BALANCER ADJUSTMENT TO MAKE IT HOLD UP THE LOAD IN ALL CASES BUT CONTACT SKILLED PERSONNEL IN CHARGE OF MAINTENANCE AT ONCE. Safety devices Drum spring breakage The balancer is fitted with a safety device that trips when the drum spring breaks and stops the balancer to prevent the hanging load from falling. If the hanging tool cannot be lifted or lowered through ordinary strain, DO NOT INSIST but contact customer service. NOTE: the balancer stops even if the drum spring is fully discharged: in this condition the head of the charge screw 45 (Fig.5) protrudes approximately 4 mm outside the cap. To restore operating conditions, use the lever 4 (Fig.6) and try to charge the spring as outlined in paragraph Balancer adjustment (release lever 4 when the head of the charge screw has re-entered the cap). If the balancer does not release, DO NOT do anything and contact customer service. Centrifugal speed limiter The balancer is fitted with a centrifugal safety system that locks the drum if the speed exceeds the danger limit (accidental unhooking of the load, cable breakage, etc.).
4 If the centrifugal safety system trips, discharge the drum spring IMMEDIATELY and completely, and have the balancer inspected by an authorized service center. Manual lock The balancer is fitted with a manual-locking system (Fig.4): turn the knob 1 to position H to stop drum rotation. Turn the knob 1 to position G for routine work conditions. NOTE: for safety reasons, the shape of the shutter that stops the drum does not allow the shutter to be removed unless it is perfectly coaxial with the matching hole in the drum: to release the drum, move the load slightly at the top and at the bottom until you find the correct position in which to release it. OPTION B : control from below (Fig.2) Lower the side of the handle with the RED tape to lock the drum; lower the side of the handle with the GREEN tape to release it. WARNING: do not leave the balancer with the drum locked and no hanging loads. WARNING: if the balancer s cable is not fully wound, and no load is applied to it, DO NOT do anything but contact the customer service at once. OPTION RI, insulated rotary suspension (Fig.3) Permits to insulate the load hung on the balancer and/or turn the hanging tool freely without twisting the cable. WARNING: always comply with the safety regulations when using electrical appliances. Installation: insert the snap-hook (31) into the pin E of the rotary suspension. Insert the cable s thimble (14) into the pin F; insert the split-pin (D) and deform it. INSPECTIONS AND MAINTENANCE Maintenance may be carried out only by skilled and authorized personnel. - Visually inspect the balancer on a regular basis (for instance once at each work shift). Specifically, check the state of the suspensions (17) and S (Fig.1), the fixing screws & self-locking systems (if used), and the condition of the hooks and cable. If the cable has the defects shown in (Fig.7), replace it immediately. Do not make any modification to the cable unit and, specifically, DO NOT SHORTEN the cable: if need, please get in touch with TECNA S.p.A. - check that the cable s movement is smooth and that it does not make any strange noises - do not lubricate the balancer with flammable or volatile fluids - do not remove any labels. Replace any damaged labels - the balancer must be inspected at least once a year by skilled, authorized personnel. Never disassemble the balancer. Maintenance is to be carried out only by skilled, authorized personnel. The static and dynamic tests (Machinery Directive 2006/42/EC, Annex I, section 4.1.3) have been performed by the manufacturer. The balancer must be disposed of complying with prevailing rules and regulations at the end of its work life. Warranty The use of non-original TECNA spare parts will negatively affect safety and performance and will, in any case, void the warranty
5
6 Translation of the Original Instructions BALANCER MAINTENANCE This part of the manual is intended for maintenance personnel ONLY CERTAIN OPERATIONS OUTLINED IN THIS SECTION ARE VERY DANGEROUS AND COULD INJURE PEOPLE IF PERFORMED BY UNSKILLED PERSONNEL. REFER TO THE OPERATING MANUAL TO INSTALL, ADJUST AND USE THE BALANCER. Maintenance The balancer s size is such that it is maintenance-free for its entire work life. However, if it is used under particularly harsh conditions and requires any interventions, ensure that the spring-drum group (13) is discharged before disassembling the balancer. Should one wish to fully discharge the spring, stop the discharging operation as soon as the spring is effectively and completely discharged (proceeding beyond this position would damage the spring which would require to be replaced). The spring is the balancer s only dangerous component. It is housed inside the drum (13) that is lubricated for life. The spring-drum spare part (13) is supplied complete: do not remove the spring for any reason whatsoever. Do not disassemble the spring group as this is a dangerous operation. Removing and inspecting the balancer - Remove the screws (40); raise the cap (5); unwind the cable completely (14); remove the shaft (11) using a plastic hammer if need be; - Inspect the spring-drum group (13): if the internal spring is broken or the cable guide groove is damaged, replace the whole group. The spring-drum group (13) is supplied assembled, lubricated and complete with bearings. Never open it for any reason whatsoever; - Check the cable (14): replace it if is has the defects shown in (Fig.7); - Inspect the disc s centrifugal weights (9) (they should be free to move) and the springs (37) that must be in perfect condition and must ensure that the centrifugal weights return. Check that the cap (5) is not damaged where the centrifugal weights act; - The centrifugal safety disc is completely assembled (9) when supplied. The only available spare parts are the springs (37); - Check the working efficiency of all the shutter kinematics (8 and 38), check the screw (45) and the pin (43) (they should slide axially and turn) and the working efficiency of the springs (6-42). Balancer assembly: - Check that the stop (50) is free to move; - Tighten the screws (49) on the retaining plate (51) of the rope (14) with a torque of 2 3 Nm - Wind the cable in the drum s helical slots (13), carefully insert it in the stop (50) and assemble; - Tighten the screws (39) of the safety disc (9) with a torque of 5 Nm; - Fit the cap (5) on the shaft (11), couple it to the cap (21) and close carefully. Tighten the screws (40) with a torque of 3 Nm; - Once done, charge the spring of the group (13) with the screw (45). Keep the shutter (8) raised, using the lever (4), until the screw head (45) re-enters the cap 5 (Fig. 5); - Install the balancer adhering to the directions supplied in the Balancer operating manual. -
7 - Spring drum breakage - If the balancer is blocked, check that the drum spring is not discharged (condition that blocks the balancer as if the spring were broken). If you are unable to charge the balancer by adhering to the procedure described in paragraph Balancer adjustment, this means that the drum spring is probably broken. WARNING: ensure that the spring is charged before carrying out any type of check. WARNING - DANGER: DO NOT open the drum and/or attempt to replace the spring for any reason whatsoever. This operation is extremely dangerous and could seriously injure anyone. WARNING - DANGER: dispose of the drum containing the broken spring in compliance with prevailing regulations. DO NOT dump it together with other waste or scrap since opening it, even accidentally, is VERY DANGEROUS and could seriously injure anyone. Use original TECNA S.p.A. spare parts only. When requesting spare parts, the Customer should kindly contact the supplier of the balancer, or the manufacturer directly, specifying the machine s identification data printed on the plate.
8
9 DICHIARAZIQNE Dl CONFORMITÀ DECLARATION OF CONFORMITY CERTIFICAT DE CONFORMITE CERTIFICADO DE CONFORMIDAD KONFORMITÄTSERKLARUNG CONFORMITETS VERKLARING Nome e indirizzo del costruttore Name and address of manufacturer TECNA S.P.A. Nom et adresse du constructeur VIA MEUCCI, 27 Nombre y direccion del constructor CASTEL S. PIETRO TERME (BO) Name und Adresse des Herstellers ITALY Naam en adres van de fabrikant Dichiariamo sotto la nostra unica responsabilità che il prodotto We declare under our sole responsibility for manufacture of the product Nous declarons sous notre seule responsabilité que le produit Certificamos bajo nuestra sola responsabilidad que el producto Wir erklären unter einziger Verantwortung, dass das Produkt Wij verklaren onder onze uitsluitende aansprakelijkheid, dat het produkt Modello - Model - Type - Modelos - Typen - Modellen BILANCIATORE BALANCER EQUILIBREUR EQUILIBRADOR FEDERZÜG BALANCER G G G G 9365G- 9366G-9367G G G 9370G G Numero di serie - Serial number - Numéro de série da/from/de/de/von/van Número de fabricación - Serie-Nummer - Serienummer a/to/a/a/bis/tot A cui si riferisce la presente dichiarazione è conforme al seguente standard: To which this declaration relates is in conformity with the following standard: Objet de certificat, est conforme à la norme suivante: DIN Objeto de este certificado, es conforme a la norma siguiente: Auf die sich die gegenwärtige Erklärung bezieht, mit folgender Norm konform ist: Waarnaar deze verklaring verwijst is conform norm: Ai sensi delle direttive CEE: Following the provisions of EEC Directives: Conforme aux prescriptions des Directives CEE: Conforme a las prescripciones y directivas de la CEE: Gemäss EG-Richtlinien Volgens de E.E.G.-Richtlijnen 2006/42/EC Nome e indirizzo della persona autorizzata a costituire il facicolo tecnico: Name and address of the person authorized to draw up the technical file: TECNA S.p.A. Nom et adresse de la personne autorisée à constituer le dossier technique: VIA MEUCCI, 27 Nombre y dirección de la persona autorizada a constituir el expediente técnico: CASTEL S. PIETRO TERME (BO) Name und Adresse der zur Erstellung des Technikheftes autorisierten Person: ITALY Naam en adres van de geautoriseerde persoon voor het samenstellen van het technische dossier: Nome e firma della persona autorizzata alla redazione della dichiarazione di conformità: Name and signature of the person authorized to write the declaration of conformity: Nom et signature de la personne autorisée à rédiger la déclaration de conformité: Nombre y firma de la persona autorizada a redactar la declaración de conformidad: Name und Unterschrift der zur Abfassung der Konformitätserklärung autorisierten Person: Naam en handtekening van de geautoriseerde persoon voor het opstellen van de conformiteitsverklaring: Caste San Pietro Terme 20/03/2012 Ezio Amadori Presidente del C.d.A. Chairman of the BOD Président du Conseil d Administration Vorsitzender des Verwaltungsrates Presidente del C.d.A.
TOTAL AIRTOOL SERVICES (UK) Ltd
TOTAL AIRTOOL SERVICES (UK) Ltd BALANCER OPERATING MANUAL Reproduced from Tecna manual Translation of the Original Instructions Install the balancer before using it. This operation is to be carried out
TOTAL AIRTOOL SERVICES (UK) Ltd
TOTAL AIRTOOL SERVICES (UK) Ltd BALANCER OPERATING MANUAL Reproduced from Tecna manual Translation of the Original Instructions Install the balancer before using it. This operation is to be carried out
TOTAL AIRTOOL SERVICES (UK) Ltd
TOTAL AIRTOOL SERVICES (UK) Ltd BALANCER OPERATING MANUAL Reproduced from Tecna manual Translation of the Original Instructions Install the balancer before using it. This operation is to be carried out
ART. ITEM MAN Edizione 10/2009
Via Grieco 25/27-40024 Castel S. Pietro Terme - Bologna (Italy) Pho. +39.051.6954400 - Tel. 051.6954411 - Telefax +39.051.6954490 http://www.tecna.net E-mail: sales@tecna.net - vendite@tecna.net MAN. 9073
ART. ITEM
MANUALE D USO DEL BILANCIATORE BALANCER OPERATING MANUAL MANUEL D UTILISATION DE L EQUILIBREUR MANUAL DE USO DEL EQUILIBRADOR BEDIENUNGSANLEITUNG FÜR FEDERZUG GEBRUIKSAANWIJZING VOOR DE BALANCER BALANSEBLOKKENS
Operating manual FP-2. Index
Operating manual FP-2 Index 1 Introduction... 2 2 Technical data... 2 3 Maintenance... 2 4 Directions of safety... 2 5 Starting... 3 6 Exhaustion... 4 7 Searching for an error... 4 8 Spare parts... 5 9
User Manual. PBA428 Weighing platform
User Manual PBA428 Weighing platform Service XXL Congratulations on choosing the quality and precision of METTLER TOLEDO. Proper use according to these instructions and regular calibration and maintenance
RoboSterz. Automatic Management of Steering Without Operator ITA. Mod. V.
RoboSterz Automatic Management of Steering Without Operator ITA Mod. V. INDEX 1. What is it "RoboSterz"... 6 1.1. Benefits... 6 1.2. Installation... 6 2. Use of RoboSterz... 7 2.1. Use of the Robosterz
TriScroll TM 300 Series Dry Scroll Vacuum Pump
vacuum technologies TriScroll TM 300 Series Dry Scroll Vacuum Pump MODULE REPLACEMENT MANUAL idealvac.com Manual No. 699904285 Revision E May 2003 (505)872-0037 idealvac.com Varian TriScroll 300 Dry Scroll
SAUTER TVO Version /2014 GB
Sauter GmbH Tel.: +49-[0]7433-9933-199 Fax: +49-[0]7433-9933-149 Internet: www.sauter.eu Instruction Manual Motorized Vertical Test Stand SAUTER TVO Version 1.3 11/2014 GB PROFESSIONAL MEASURING TVO-BA-e-1413
Operating and maintenance instructions
Operating and maintenance instructions Fleece disc Klünder disc Hermann Klünder GmbH Brückenstraße 1 D-31628 Landesbergen Tel: +49(0)5025/94073, Fax: 49 (0) 5025/94074 www.mietenpflege.de Table of Contents
N CX 5500 DAT Operating and Instruction manual
N0. 148258 00 DAT.1998-10-26 CX 5500 Operating and Instruction manual ENGLISH CX 5500 Technical data m = 8.6 kg = 43 db(a) U = 120/230 V f = 50/60 Hz T = 0-30 C Must only be used for * Spot suction of
Sandfiltration kit + Swimmey pump
Sandfiltration kit + Swimmey pump INSTALLATION ENGLISH INSTRUCTIONS The manufacturer has the right to modify the products without previous notice for as far as their characteristics are not really changed
BLUSPM24. Instruction manual. Battery powered hydraulic pressing tool
Instruction manual BLUSPM24 Battery powered hydraulic pressing tool Drainage and pressure piping solutions PO Box 107; Corunna Avenue, Melrose Park SA 5039 T: 08 8374 3426 blucher@blucher.com.au www.blucher.com.au
User manual / 230 V. Electronically controlled motor, constant torque with intermediate reverse
User manual 16800-115 / 230 V Electronically controlled motor, constant torque with intermediate reverse TABLE OF CONTENTS Chap. Description Page 1 GENERALITY 1 2 Recommendations and percautions before
POWER SPRAYER MODEL S151/S201 ASSEMBLY DRAWINGS AND PARTS CATALOGUE
POWER SPRAYER MODEL S151/S201 ASSEMBLY DRAWINGS AND PARTS CATALOGUE Use this guide along with the parts lists attached to locate and identify components of your sprayer. When ordering replacement parts,
BLUCP 700E. Instruction manual. Compact hydraulic pump with accumulator
Instruction manual Compact hydraulic pump with accumulator BLUCP 700E Drainage and pressure piping solutions PO Box 107; Corunna Avenue, Melrose Park SA 5039 T: 08 8374 3426 M: 0425 567 241 spaterson@blucher.com.au
REVERSIBLE HYDRAULIC PLATE COMPACTOR BR5100 PARTS BOOK
REVERSIBLE HYDRAULIC PLATE COMPACTOR BR5100 PARTS BOOK www.bartellglobal.com Doc. # OI-B19025 Orig. Rel. 10/2013 Curr Rev. - 05 www.bartellglobal.com Bartell Morrison Inc. 375 Annagem Boulevard Mississauga,
Crane fork KGM/KGA and KGQ/KGL
Crane fork KGM/KGA and KGQ/KGL Operating manual This equipment must not be installed, operated or maintained by any person who has not read and understood all the contents of this manual - 1 - Table of
Beton Trowel nv INSTRUCTION MANUAL SLAB SAW BTCS500 - GEBABEBB BBRUBEBB BNP FORTIS: ING: BE BE
INSTRUCTION MANUAL SLAB SAW BTCS500 BBRUBB 1/20 Use this guide along with the parts lists attached to locate and identify components of your saw. When ordering replacement parts, be sure to provide the
User manual Humdinger concrete vibrator
www.betontrowel.com 1590130051 BETONTROWEL.COM User manual Humdinger concrete vibrator 2015 IP44 I 2 Introduction Legal note This user manual contains the original instructions, written in the English
b3c OPERATING MANUAL (GB) 9260(A) (A) 9360 Compacts scales 9260 (A) Ver 2014 EN September BC
b3c pesage 9260(A) 9360 Compacts scales 9260(A) 9360 OPERATING MANUAL (GB) 9260 (A) - 9360 Ver 2014 EN September BC 9260(A) - 9360 INSTRUCTION FOR USE AND MAINTENANCE Thank you for choosing the professional
Sugar beet covering eqipment
Operating and maintenance instructions Sugar beet covering eqipment KL 2000 Hermann Klünder GmbH Brückenstraße 1 31628 Landesbergen Tel: +49(0)5025/94073 Fax: +49(0)5025/94074 www.mietenpflege.de Table
POWER SPRAYER Model: S151 and S201 Operator s Manual
POWER SPRAYER Model: S151 and S201 Operator s Manual 200 COMMERCE DRIVE, FREEHOLD, NEW JERSEY, USA, 07728, 732-566-5400 FAX 732-5444 Doc. # OI M09205 Orig. Rel. 07/2008 Curr. Rev. 04 Rev. Date 06/2014
OPERATING INSTRUCTION
en OPERATING INSTRUCTION 86152-13EN G 09/11 Halogen Light Arrow HLPK13 ( flashing arrow / flashing cross ) part no. 21023 Halogen Light Arrow HLPK13 ( flashing arrow / flashing cross ) with electric motor
Operating instructions
Operating instructions BB www.bron.ch Operating instructions Powerbox 900 by bron Before use We are pleased you have chosen a Powerbox 900 by bron which is a high-quality product in every respect. If used
MT- 40 HOG TOE NOTCHER
Page 1 of 16 MT- 40 MANUAL INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. TOOL DATA
POTATO DIGGER WITH OSCILLATING SIEVES DM 100
Del Morino srl, v.caroni di Sotto 19, I-52033 Caprese Michelangelo AR Italy Ph: +39-575-791059 Fax: +39-575-791210 E.mail: export@del-morino.it http://www.del-morino.it USE AND MAINTENANCE MANUAL POTATO
INSTRUCTIONS & MAINTENANCE SHEET HYDROTEST PUMPS
INSTRUCTIONS & MAINTENANCE SHEET HYDROTEST PUMPS HAP0070, HAP0130, HAP0180, HAP0250, HAP0400, HAP0740, HAP1300, HAP1900, HAP2900 V03.2013 DECLARATION OF CONFORMITY DECLARACION DE CONFORMIDAD LARZEP, S.A.
Mod: KLD6-12/35XLAS-N
12/2011 Mod: KLD6-12/35XLAS-N Production code: 1914070 INSTRUCTION MANUAL LOGIC LINE PLUS HOOD Reseller Stamp for Warranty Dear customer, Above all, thank you for choosing our product and we would like
BARTELL MORRISON INC. 375 Annagem Blvd., Mississauga, ON L5T 3A7 Telephone: Fax: CONCRETE MIXER
BARTELL MORRISON INC. 375 Annagem Blvd., Mississauga, ON L5T 3A7 Telephone: 1-647-953-4100 Fax: 1-647-953-4101 CONCRETE MIXER MC6PH160, MC6PE150, MC75SH160, MC75SE200, MC95PH240, MC95PE200, MC95SH240,
TYPE 41LA MINING LED LUMINAIRE EXPLOSION PROOF LUMINAIRE WITH FLAMEPROOF PROTECTION (TYPE d)
Victor Products Ltd New York Way New York Industrial Park Newcastle upon Tyne NE27 0QF ENGLAND Tel : +44(0)191 2808000 Fax : +44(0)191 2808080 0518 Making Hazardous Environments Work TYPE 41LA MINING LED
Adam Equipment. TBB - TRIPLE BEAM Mechanical Balance Manual. 8141, RevD Nov2015 (ENG)
Adam Equipment TBB - TRIPLE BEAM Mechanical Balance Manual 8141, RevD Nov2015 (ENG) @Adam Equipment Company 2015 P.N. 8141, RevD Nov2015) CONTENTS / INHALT / TABLE DES MATIERES / CONTENIDO / CONTENUTO
UNI-SCREED MANUAL OWNER S MANUAL AND PARTS LIST
OWNER S MANUAL www.bartellglobal.com Doc. # OIPB-B19040 Orig. Rel. 01/2017 Curr. Rev. - 02 www.bartellglobal.com Bartell Morrison Inc. 375 Annagem Boulevard Mississauga, Ontario, Canada L5T 3A7 Tel: (647)
Dumper OPERATOR S MANUAL
1000185002 3.2 0608 Dumper 3001 OPERATOR S MANUAL 1 0 0 0 1 8 5 0 0 2 1 Introduction 1.1 Important information on this Operator's Manual Please store the Operator's Manual in the storage bin under the
VOLUMETRIC PUMPS. BOMBA ELIAS has developed the volumetric for clean water suitable for small flow rates and average height.
VOLUMETRIC PUMPS NIZA PISCIS Introduction: BOMBA ELIAS has developed the volumetric for clean water suitable for small flow rates and average height. NIZA series are technopolymers volumetric pumps, and
Product Information Overspeed governor GB 260
Product Information GB 260 Copyright as per DIN ISO 16016. Manufactured under licence of C. Haushahn GmbH & Co. I Subject to modification. Published by SLC Sautter Lift Components GmbH & Co. KG Borsigstrasse
TriScroll TM 300 Series Dry Scroll Vacuum Pump
vacuum technologies TriScroll TM 300 Series Dry Scroll Vacuum Pump TIP SEAL REPLACEMENT MANUAL DRAFT 12/21/04 Manual No. 699904280 Revision H December 2004 TriScroll 300 Series Dry Scroll Vacuum Pump DRAFT
TYPE NO. AS APPROPRIATE
Victor Products Ltd New York Way New York Industrial Park Newcastle upon Tyne NE27 0QF ENGLAND Tel : +44(0)191 2808000 Fax : +44(0)191 2808080 0518 Making Hazardous Environments Work A42 RANGE OF 250AMP
Operation instructions Platform/floor scales
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: info@kern-sohn.com Tel: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Operation instructions Platform/floor scales KERN EOB/EOE/EOS/BOBP
Dumper 1001, 1501, 2001 OPERATOR S MANUAL
1000184998 2.3 0608 Dumper 1001, 1501, 2001 OPERATOR S MANUAL 1 0 0 0 1 8 4 9 9 8 1 Introduction 1.1 Important information on this Operator's Manual Please store the Operator's Manual in the storage bin
OWNER S MANUAL SINGLE DIRECTION PLATE COMPACTORS B100 B200 B300 ORIGINAL LANGUAGE
OWNER S MANUAL SINGLE DIRECTION PLATE COMPACTORS B100 B200 B300 ORIGINAL LANGUAGE Doc. # OIB09017 Orig. Rel. 08/2010 Curr. Rev. 02 01 Rev. Date 06/2014 08/2010 Bartell Morrison (USA) LLC 375 Annagem Blvd.
Operating Instructions
Operating Instructions Conversion box Model No. WV-TC312/WV-TC312E (The stand is removed from the conversion box in this illustration.) Before attempting to connect or operate this product, please read
MKT Series AUDIPACK. AUDIPACK Industriestraat GT Moerkapelle The Netherlands
UDIPCK UDIPCK Industriestraat 2 2751 GT Moerkapelle The Netherlands Tel: +31(0)795931671 Fax: +31(0)795933115 Email: audipack@audipack.com www.audipack.com MKT Series MKT Series-01-2010-02 MKT Series CHECKLIST
Instructions for Use Plain Trolley ULK Geared Trolley UHK
Instructions for Use Plain Trolley Geared Trolley Item no. Load-carrying capacity (payload) Weight Trolley widths *special trolley widths* Device dimensions mm H / W / D Minimum curve radius mm -005 0,5
Operating Instructions School Balance
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: info@kern-sohn.com Tel: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Operating Instructions School Balance KERN Version
INSTRUCTION MANUAL ABIS-06 Premium airmotor
INSTRUCTION MANUAL ABIS-06 Premium airmotor www.beveltools.com 01-2015 For your safety, please read manual thoroughly before operating. After reading this manual, keep it in a place that the user always
POWER SUPPLY UNIT FOR 3 KW MAGNETRON TECHNICAL NOTE
POWER SUPPLY UNIT FOR 3 KW MAGNETRON TECHNICAL NOTE (Issue April 2004) CE Declaration of Conformity Dichiarazione di Conformità CE Manufacturer s Name: Nome del Costruttore: Manufacturer s Address: Indirizzo
Operating Instructions Precision balance
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: info@kern-sohn.com Tel: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Operating Instructions Precision balance KERN Version
INSTRUCTION MANUAL SMART MT CLUTCH. Columbia 1
INSTRUCTION MANUAL SMART MT CLUTCH Columbia 1 SMART MT - CLUTCH Content 1. SAFETY STANDARDS page 3 2. TECHNICAL DATA page 5 3. ACCESSORIES page 5 4. TOOL COMPOSITION page 6 5. TOOL INSTALLATION page 6
Infratek 23DC-Source Tester
Infratek 23DC-Source Tester User s Manual Infratek TABLE OF CONTENTS 1. Safety, Working with Batteries can be dangerous 2. Introducing the Infratek 23 DC-Source Tester 3. Features of the Infratek 23 DC-Source
Communicating Electronic Control for Fan Coil Units Régulation électronique communicante pour ventilo-convecteurs
Installation and maintenance manual Manuel d installation et de maintenance R English Français Communicating Electronic Control for Fan Coil Units Régulation électronique communicante pour ventilo-convecteurs
RFID114. For use in combination with charge controllers used in electric vehicle charging stations, wall boxes or street light charging points.
EN Manual RFID114 For use in combination with charge controllers used in electric vehicle charging stations, wall boxes or street light charging points RFID114_D00328_00_M_XXEN/04.2018 Bender GmbH & Co.
OPERATOR S MANUAL INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK
OPERATOR S MANUAL INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK REV D: 11/24/04 IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. TOOL
Adam Equipment. User Manual (EN) Pricing Retail RAV Series Adam Equipment Co. Ltd.
Adam Equipment Pricing Retail RAV Series User Manual (EN) (P.N. 3.02.6.6.12923, Revision 1.00, Effective Feb2016 ENG/FR/DE/ES) 2016 Adam Equipment Co. Ltd. ENGLISH: P 1-4 FRANÇAIS: P 5-9 DEUTSCH: P 10-16
SERVO MOTORS BRUSHLESS SERVO MOTORS OPERATING INSTRUCTIONS 2016
SERVO MOTORS BRUSHLESS SERVO MOTORS OPERATING INSTRUCTIONS 2016 3009/16 en Ed.02.2016 Read these Operating Instructions before performing any transportation, installation, commissioning, maintenance or
ECD 16,8. Art.-No.: Operating Instructions Battery-powered Drill/Screwdriver with Adjustable Torque
Anleitung ECD 16,8 25.10.2001 7:49 Uhr Seite 1 Operating Instructions Battery-powered Drill/Screwdriver with Adjustable Torque Art.-No.: 45.196.07 ECD 16,8 Anleitung ECD 16,8 25.10.2001 7:49 Uhr Seite
Model RGC-100 Series Digital Vacuum Gauge
vacuum technologies Model RGC-100 Series Digital Vacuum Gauge RGC-100 Ranges.001 to 760 Torr.001 to 991 millibar INSTALLATION AND OPERATION MANUAL DRAFT 5/28/10 Manual No. RGC100M Revision A May 2010 Varian
LHS/LHSa SERIES Manual
Adam Equipment LHS/LHSa SERIES Manual (P.N. 7.00.6.6.0200, Revision B November 2012) Software version L1.1/LA1.1 Adam Equipment Company 2012 1.0 CONTENTS 1.0 CONTENTS... 1 2.0 INTRODUCTION... 2 2.1 FEATURES...
POWER SUPPLY UNIT FOR 2 KW MAGNETRON TECHNICAL NOTE
POWER SUPPLY UNIT FOR 2 KW MAGNETRON TECHNICAL NOTE (Issue October 2004) CE Declaration of Conformity Dichiarazione di Conformità CE Manufacturer s Name: Nome del Costruttore: Manufacturer s Address: Indirizzo
DUNE DCT SERIES Manual
Adam Equipment DUNE DCT SERIES Manual (P.N. 9384, Revision B3, March 2016) Adam Equipment Company 2016 Easy Reference: Model name of the scale: Serial number of the unit: Software revision number (Displayed
Temperature Probes for Heat Meters
Temperature Probes for Heat Meters Basic types 902428/20 and 902428/70 Operating Manual 90242820T90Z001K000 V1.00/EN/00709221 Contents Contents 1 Safety information...............................................
Cert if ied St ainl ess St eel 316L Lif t ing Eye Nut
Cert if ied St ainl ess St eel 316L Lif t ing Eye Nut DIN 582:2010/ A4 (ISO 3266 UNI 2947) Italian manufactured stainless steel Lifting Eye nuts in accordance with standard DIN 582:2010 A4 (AISI 316L)
Translation of the Original operating instructions Lifting device Z 70 /...
Translation of the Original operating instructions Lifting device Z 70 /... Content 1. Lifting device / Correct use according to regulations 2. Basic principles 3. General information 4. Special remarks
PEMO PUMPS HORIZONTAL 403 AO/AB-AS-B3
Uffici e Stabilimento: 20090 VIMODRONE (MI) Via Pascoli, 17 ITALY Tel. +39/02250731 Fax. +39/022500371 Web site: www.pemo.com E-mail: peris@pemo.com PEMO PUMPS HORIZONTAL 403 AO/AB-AS-B3 MOTOR WITH BOTH
KERN HFB Version GB
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen email: info@kern-sohn.com Phone: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Operating instructions Electronic Crane Scales Logbook
RIDUTTORE PER MOTORI ENDOTERMICI REDUCTION GEAR FOR GASOLINE & DIESEL ENGINES
RS99 RIDUTTORE PER MOTORI ENDOTERMICI REDUCTION GEAR FOR GASOLINE & DIESEL ENGINES RÉDUCTEUR POUR MOTEURS À COMBUSTION INTERNE UNTERSETZUNGSGETRIEBE FÜR VERBRENNUNGSMOTOREN ISTRUZIONI D USO OPERATING INSTRUCTIONS
OPERATOR S MANUAL INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK
OPERATOR S MANUAL INCLUDING: OPERATION, INSTRUCTION, INSTALLATION, MAINTENANCE AND PARTSBOOK REV C: 02/21/05 IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. TOOL
A408 GB. Pneumatic oil and diesel pumps 1:1
03 594 A408 GB Pneumatic oil and diesel pumps 1:1 G Operating instructions for Pneumatic oil and diesel pump 1:1 Contents 1. General details 2 1.1 Intended use 2 1.2 Design and functional description 2
Mod. SC Man09. Manual sliding door USER AND MAINTENANCE MANUAL
USER AND MAINTENANCE MANUAL Manual sliding door Mod. SC Man09 Frigo Doors by Sevenfrigo srl Via della Tecnica 44 Z.I. Molinaccio 06135 loc. Ponte S. Giovanni - PERUGIA (PG) - ITALY Tel: +39 075 5997648
WALK-BEHIND TROWELS B424 B430 BC436 BC446 B436 B446 MEGA-T B446 OWNER S MANUAL
B424 B430 BC436 BC446 B436 B446 MEGA-T B446 www.bartellglobal.com Doc. # OI-B19001 Orig. Rel. 08/2016 Curr Rev. - 01 www.bartellglobal.com Bartell Morrison Inc. 375 Annagem Boulevard Mississauga, Ontario,
EC DECLARATION OF CONFORMITY FOR MACHINES (DIRECTIVE 98/37/EC) WARNINGS FOR THE INSTALLER
EC DECLARATION OF CONFORMITY FOR MACHINES (DIRECTIVE 98/37/EC) Manufacturer: Address: Declares that: FAAC S.p.A. Via Benini, 1-40069 Zola Predosa BOLOGNA - ITALY 740-24V mod. operator is built to be integrated
Q Flood 7500 Rugged Battery powered LED User s Manual
Q Flood 7500 Rugged Battery powered LED User s Manual 2015 City Theatrical, Inc. Contents Disclaimer... 2 Product Modification... 3 System Compliance Information... 5 Safety Notices... 6 Introduction...
KERN HFB Version /2012 GB
PCE Americas Inc. 711 Commerce Way Suite 8 Jupiter FL-33458 USA From outside US: +1 Tel: (561) 320-9162 Fax: (561) 320-9176 info@pce-americas.com PCE Instruments UK Ltd. Units 12/13 Southpoint Business
Rescue Pac. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference
Please dispose of Packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate
HOG BUNG DROPPER IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL. BUNG GUN_
OPERATOR S MANUAL [ENGLISH]: HOG BUNG DROPPER INCLUDING: OPERATION, INSTRUCTION, INSTALLATION AND MAINTENANCE IMPORTANT: READ THIS MANUAL CAREFULLY BEFORE INSTALLING, OPERATING OR SERVICING THIS TOOL.
www.pce-group-europe.com PCE- Deutschland Gmb H & Co. KG el: +49 029 03 976 99-0 Fax: +49 029 03 976 99-29 info@warensortiment.de www.warensortiment.de PCE Group Ibérica S.L. el: +34 967 543 548 Fax: +34
CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080
CO 3-WAY PNEUMATIC VALVE INSTRUCTION MANUAL 2080 STI S.r.l has taken every care in collecting and verifying the documentation contained in this Instruction Manual. The information herein contained are
EC MACHINE DIRECTIVE COMPLIANCE DECLARATION
EC MACHINE DIRECTIVE COMPLIANCE DECLARATION (DIRECTIVE 89/392 EEC, APPENDIX II, PART B) Manufacturer: FAAC S.p.A. Address: Via Benini, 1 40069 - Zola Predosa BOLOGNA - ITALY Hereby declares that: the 770
EC MACHINE DIRECTIVE COMPLIANCE DECLARATION
770 EC MACHINE DIRECTIVE COMPLIANCE DECLARATION (DIRECTIVE 89/392 EEC, APPENDIX II, PART B) Manufacturer: FAAC S.p.A. Address: Via Benini, 1 40069 - Zola Predosa BOLOGNA - ITALY Hereby declares that: the
RI.15KI. L Rev. 04/03/02 MIKROCONTROLLER-STEUERUNG FÜR. Betriebsanleitung
L8542624 Rev. 04/03/02 CENTRALINA A MICROPROCESSORE PER CTROL UNIT WITH MICROCTROLLER FOR MIKROCTROLLER-STEUERUNG FÜR CENTRALE A MICROCTRÔLEUR POUR CENTRALITA A MICROPROCESADOR POR RI.15KI UNI EN ISO 9001
Corso Principi di Piemonte, 65/ RACCONIGI (CN) ITALY tel fax
V2 S.p.A. Corso Principi di Piemonte, 65/67 12035 RACCONIGI (CN) ITALY tel. +39 01 72 81 24 11 - fax +39 01 72 84 050 info@v2home.com - www.v2home.com IL n.131 EDIZ. 28/08/2012 Bingo I GB F E P D NL ATTUATORE
Operating Instructions Garlock Butterfly Valves DN : mm / 2-24
Operating Instructions Garlock Butterfly Valves DN : 50-600 mm / 2-24 PN : 10 / 16 Type: GAR-SEAL SAFETY-SEAL STERILE-SEAL MOBILE-SEAL Conformity declaration... 14 0 Introduction... 15 1 Proper use...
INSTRUCTIONS FOR USE FACE GEARBOXES
INSTRUCTIONS FOR USE FACE GEARBOXES TNC MTC-TC KTM ES Declaration of Conformity Producer: TOS ZNOJMO, akciová společnost Družstevní 3 CZ 669 02 Znojmo Equipment: Face gearboxes Type/ Modification:MTC,
Pro Booster 802Li. Please read and fully understand the instructions in this manual before operation. Keep this manual safe for future reference.
Please dispose of packaging for the product in a responsible manner. It is suitable for recycling. Help to protect the environment, take the packaging to the local amenity tip and place into the appropriate
Installation manual ASTER AUTOMATION FOR SWING GATES 11_16
Installation manual ASTER AUTOMATION FOR SWING GATES 11_16 Contents 1. GENERAL SAFETY PRECAUTIONS... page 01 2. INTENDED USE AND APPLICATION... page 01 2.1 Kit contents... page 01 2.2 Technical features...
CE DECLARATION OF MACHINE CONFORMITY
CE DECLARATION OF MACHINE CONFORMITY (DIRECTIVE 2006/42/EC) Manufacturer : Address: Declares that: FAAC S.p.A. Via Calari, 10-40069 Zola Predosa BOLOGNA - ITALY Operator mod. 541 3ph is built to be incorporated
Instruction Manual for Ceramics up to 1320 C
Instruction Manual for Ceramics up to 1320 C ELS-S Ergo Load System Contents Page 1. PREFACE 3 2. IMPORTANT SAFETY INSTRUCTIONS 3 2.1. General information 3 2.2. General safety instructions 3 2.3. Technical
Working Instructions Translation
WIDOS Einsteinstr. 5 Phone +49 (0) 71 52 99 39-0 W. Dommer Söhne GmbH D-71254 Ditzingen-Heimerdingen Fax +49 (0) 71 52 99 39-40 Website: www.widos.de Email: info@widos.de Working Instructions Translation
TIRE CHANGING MACHINE ST-215 INSTRUCTIONS MANUAL
TIRE CHANGING MACHINE ST-215 INSTRUCTIONS MANUAL COD.XXXXXX Rev.0 ST-215 WARNINGS The present instructions booklet is an integral part of the product. Carefully study the warnings and instructions contained
Instruction Manual Electronic Crane Scales. Logbook Regular maintenance and care KERN HUS/HUM Version /2011 GB
KERN & Sohn GmbH Ziegelei 1 D-72336 Balingen E-Mail: info@kern-sohn.com Tel: +49-[0]7433-9933-0 Fax: +49-[0]7433-9933-149 Internet: www.kern-sohn.com Instruction Manual Electronic Crane Scales Logbook
OPERATING INSTRUCTIONS (Translation) Hoisting crane
1. User Groups Duties Operator Operation, visual inspection Specialist personnel OPERATING INSTRUCTIONS (Translation) Hoisting crane Type 4781.0,25 Assembly, disassembly, repair, maintenance Tests GB Qualifications
Sparkasse zu Lübeck (Sort code ) Acc.No
Instruction manual Refraction unit bon E-50 GA bon E-50 Rev 1.0 E 211005.doc PO Box 32 26 23581 Lübeck Phone: 0451/ 80 900-0 Fax: 0451/ 80 900-10 Sparkasse zu Lübeck (Sort code 230 501 01) Acc.No. 1 014
HST -LS Interlocking device (Translation of Original Manual)
Installation and Operating Manual for Components HST -LS Interlocking device (Translation of Original Manual) HST-LS Ident.-No.: 10268 HST-LS Ident.-No.: 10269 HST-LS, pictured Ident-Nr. 10269 The image
IMG-100 Inverted Magnetron Gauge
vacuum technologies IMG-100 Inverted Magnetron Gauge INSTRUCTION MANUAL Manual No. 699908220 Revision B May 2004 Copyright 2004 Vacuum Technologies Warranty Products manufactured by Seller are warranted
Instructions for use L 2015
Instructions for use L 2015 17 Safety instructions Only use the L 2015 charger for charging the BA 2015 accupack! Never try to charge other rechargeable batteries or non-rechargeable batteries! Keep liquids
TC 32 Hp 4 TC 42 Hp 5 TC 42 Hp 7 TC 42 Hp 10 INDUSTRIAL MINCER. TC_32-42_IND_004 Ed AUTHORISED DEALER USE AND MAINTENANCE MANUAL
AUTHORISED DEALER 24 INDUSTRIAL MINCER USE AND MAINTENANCE MANUAL 1 TC 32 Hp 4 TC 42 Hp 5 TC 42 Hp 7 TC 42 Hp 10 TC_32-42_IND_004 Ed. 06.2008 2 23 Contents 1. Delivery and warranty 5 1.1 Introduction.
UNDERGROUND OPERATOR FOR SWINGING GATES. WARNING!! Before installing, thoroughly read this manual that is an integral part of the pack
UNDERGROUND OPERATOR FOR SWINGING GATES COMPAS 2 WARNING!! Before installing, thoroughly read this manual that is an integral part of the pack Our products if installed by qualified personnel capable to
INSTALLATION MANUAL FOR SWING SHUTTERS KAF212. FACE S.r.l. Viale delle Industrie, Dosson di Casier Treviso Italy
INSTALLATION MANUAL FOR SWING SHUTTERS KAF212 FACE S.r.l. Viale delle Industrie, 74 31030 Dosson di Casier Treviso Italy INDEX Subject Page 1. General safety instruction 2 1.1 EC marking and European directives
INSTRUCTIONS FOR INSTALLATION
HYDRAULIC OPERATOR MODO 110-110/L FOR SINGLE- OR DOUBLE-WING SWING GATES INSTRUCTIONS FOR INSTALLATION GENERAL WARNINGS These warnings constitute an integral and essential part of the product and must