INSTALLATION INSTRUCTIONS

Size: px

Start display at page:

Download "INSTALLATION INSTRUCTIONS"

Ethan Stafford
5 years ago
Views:

1 Accessory Application Publication No. INSTALLATION INSTRUCTIONS SADDLEBAG STAY P/N 08L73-MJF-A00ZP CTX700N/ND (Pages 1-6) CTX700/D (Pages 6-11) MII Issue Date March 2013 PARTS LIST INNER SUPPORT (CTX700N/ND Only Sold separately (1) (12) (2) (1) (3) (5) (14) (8) (2) (4) No. Description Qty (11) (1) Right inner support stay 1 (2) Left inner support stay 1 (6) (4) (3) 8 mm flange bolt 6 (4) Cushion 2 (9) (5) Installation Instruction URL 1 (7) (5) TOOLS REQUIRED Socket (12 mm) Ratchet (3) Hex wrench (4 and 6 mm) Ruler (10) (13) Torque wrench TORQUE CHART Tighten all screws, bolts, and nuts to their specified torque values. Refer to the Service Manual for the torque values of the removed parts. No. Description Qty (1) Right saddlebag hook 1 (2) Left saddlebag hook 1 (3) Saddlebag bracket 2 Item N m kgf m lbf ft 6 mm socket bolt mm socket bolt mm flange bolt (4) Collar (small-thin) 2 (5) Collar (small-thick) 2 (6) 6 mm socket bolt 4 (7) Washer 4 (8) Right saddlebag support stay 1 (9) Left saddlebag support stay 1 (10) Rubber stop 2 (11) Collar (large) 4 (12) 8 mm flange bolt 4 (13) Installation Instruction URL 1 (14) 8 mm socket bolt (Not used.) Honda Motor Co., Ltd. - All Rights Reserved. 1 of 11 08L73-MJF-A00ZP

2 INSTALLATION (CTX700N/ND) CAUTION To prevent burns, allow the engine, exhaust system, radiator, etc. to cool before installing the accessory. NOTE: Take care not to damage the painted surfaces of the motorcycle. Illustrations show CTX700N type, CTX700ND type is similar. 2. Refer to the Service Manual for the motorcycle, remove the rear cowls. 1. Refer to the Service Manual for the motorcycle, remove the seat. SEAT LEFT REAR COWL CLIP 3. Refer to the Service Manual for the motorcycle, remove the covers from the inside of the rear cowls. SCREW COVER LEFT REAR COWL 2 of 11

3 4. Refer to the Service Manual for the motorcycle, remove the radiator covers. 6. Refer to the Service Manual for the motorcycle, remove the muffler cover. LEFT RADIATOR COVER MUFFLER COVER 5. Refer to the Service Manual for the motorcycle, remove the shelters. 7. Refer to the Service Manual for the motorcycle, remove the left rear under cover. CLIP LEFT REAR UNDER COVER LEFT SHELTER 3 of 11

4 8. Refer to the Service Manual for the motorcycle, remove the pivot covers. 10. Install the saddlebag support stays as shown. NUTS (Reuse) LEFT PIVOT COVER 9. Refer to the Service Manual for the motorcycle, remove the front hook stays. NUT S (Reuse) SUPPORT STAY 11. Refer to the Installation Instructions for the separately sold inner support, install the inner support to the motorcycle. 12. Loosely install the saddlebag hooks as shown. 8 mm FLANGE HOOK NUT S LEFT FRONT HOOK STAY S (large) 4 of 11

5 When installing the Backrest bracket (Sold separately) 13. Install the rubber stop as shown. Make two sets. 8 mm FLANGE 52 mm RUBBER STOP HOOK BACKREST BRACKET (thin) RUBBER STOP (thick) 14. Install the saddlebag bracket as shown. 6 mm SOCKET (small-thin) WASHER (small-thick) 5 of 11

6 15. Install saddlebags as shown. LOOP Insert into the hook. 17. Tighten all loosely installed hardware to the specifications in the torque chart. The right side is same. Tighten. HOOK HANDLE LEVER Install the saddlebag case with the handle lever raised. 16. Lower the handle lever as shown. HANDLE LEVER INSTALLATION (CTX700/D) CAUTION To prevent burns, allow the engine, exhaust system, radiator, etc. to cool before installing the accessory. NOTE: Take care not to damage the painted surfaces of the motorcycle. Reinstall the removed parts on the motorcycle and make sure that wires and harnesses are not pinched. Disconnect the negative (-) cable from the battery before installing this accessory. The memory of the clock will be erased when you disconnect the battery. Reset the clock after reconnecting the battery. Illustrations show CTX700 type, CTX700D type is similar. 6 of 11

7 1. Refer to the Service Manual for the motorcycle, remove the seat, and disconnect the negative (-) cable from the battery as shown. SEAT 3. Refer to the Service Manual for the motorcycle, remove the rear cowls. LEFT REAR COWL NEGATIVE (-) CABLE CLIP 2. Refer to the Service Manual for the motorcycle, remove the rear grips. 4. Refer to the Service Manual for the motorcycle, remove the inner covers. S CAP LEFT REAR GRIP RIGHT INNER COVER WASHER LEFT INNER COVER S 7 of 11

8 5. Refer to the Service Manual for the motorcycle, remove the windscreen moulding. WINDSCREEN MOULDING 7. Refer to the Service Manual for the motorcycle, remove the shelters. CLIP 6. Refer to the Service Manual for the motorcycle, remove the front side cowls. FLANGE RIGHT FRONT SIDE COWL LEFT SHELTER WASHER 8. Refer to the Service Manual for the motorcycle, remove the muffler cover. CONNECTOR Disconnect. MUFFLER COVER LEFT FRONT SIDE COWL 8 of 11

9 9. Refer to the Service Manual for the motorcycle, remove the left rear under cover. 11. Refer to the Service Manual for the motorcycle, remove the front hook stays. NUT LEFT REAR UNDER COVER NUT 10. Refer to the Service Manual for the motorcycle, remove the pivot covers. S LEFT FRONT HOOK STAY 12. Install the saddlebag support stays as shown. NUTS (Reuse) LEFT PIVOT COVER S (Reuse) SUPPORT STAY 13. Install the rear cowls in the reverse order of removal. 9 of 11

10 14. Loosely install the saddlebag hooks as shown. 15. Install the rubber stop as shown. Make two sets. 8 mm SOCKET LEFT REAR GRIP (Reuse) 52 mm RUBBER STOP HOOK S (large) When installing the Backrest bracket (Sold separately) 8 mm SOCKET LEFT REAR GRIP (Reuse) RUBBER STOP 16. Install the saddlebag bracket as shown. 6 mm SOCKET HOOK (small-thin) WASHER (small-thick) BACKREST BRACKET (thick) (thin) 10 of 11

11 17. Install the saddlebags as shown. LOOP Insert into the hook. 19. Tighten all loosely installed hardware to the specifications in the torque chart. Left side shown, right side is the same. Tighten. HOOK HANDLE LEVER Install the saddlebag case with the handle lever raised. 20. Install the caps as shown. CAPS (Reuse) LEFT REAR GRIP 18. Lower the handle lever as shown. HANDLE LEVER 11 of 11

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS Accessory TRUNK INSTALLATION KIT P/N 08L73-MKC-A10ZA Application GL1800B/BD Honda Dealer: Please give a copy of these instructions to your customer. Publication No. MII 16426