Ultimate Support. V-Stand Pro USER MANUAL VSIQ-200B / Ultimate Support IQ Rev UM-KEY-VSIQ-200B

Transcription

1 Ultimate Support V-Stand Pro USER MANUAL VSIQ-200B / Ultimate Support IQ-3000 Rev UM-KEY-VSIQ-200B

2 STEP 1 Prepare V-Stand Pro or IQ-3000 Prepare V-Stand Pro Prepare IQ-3000 STEP 1A Identify the back end of the support arm of the V-Stand Pro. STEP 1A Identify the back end of the support arm of the IQ STEP 1B Slide the support arm back to make room for Second Tier Assembly by lifting it up at an angle, then sliding it down until fully extended. Lay arm flat onto collar. STEP 1B Slide sleeve forward to make room for Second Tier Pro assembly. STEP 1C Using a flathead screwdriver, carefully detach end cap. STEP 1C Using a flathead screwdriver, carefully detach end cap. Page 2

3 STEP 2 Assemble Support Arms Parts Used: A. Two (2) Support Arms B. Two (2) Riser Tubes E. Two (2) Z-knobs F. Two (2) Washers G. Two (2) Small Springs H. Two (2) Nuts STEP 2A Place Nut (H) in well of Riser Tube (B) on opposite side of teeth. (NOTE: Until assembled, may fall out do not lose!) STEP 2B Place one Small Spring (G) in the well at the center of the teeth of both Support Arm (A) and Riser Tube (B). Press and hold together. STEP 2C Place washer on Z-knob (E). Assemble by screwing Z-knob (E) into Nut (H) through Riser Tube (B) and Support Arm (A). STEP 2D Repeat STEPS 2A-2C for second assembly. Page 3

4 STEP 3 Attach Clamps and Arms to Stand STEP 3A Loosen Z-knob on End Clamp and rotate until bubble level and Riser Tube receiver are perpendicular (see picture above). STEP 3B Slide End Clamp onto end of stand support arm. (NOTE: Make sure End Clamp is as far onto the support arm as possible.) STEP 3C Utilizing the leveling bubble, ensure End Clamp is level. Secure by flipping the quick release lever toward End Clamp (which can be tightened, or loosened using a flathead screwdriver). STEP 3D Using printed height markers, choose desired height and adjust Memory Collar position to that line. (NOTE: Leave slightly loose, as you will tighten completely in STEP 3F.) STEP 3E Place Second Tier Pro Support Arms in End Clamp receivers. Page 4 STEP 3F Memory Collar will lock into place in End Clamp receiver groove. After ensuring desired height, make sure 1st tier and 2nd tier support arms are parallel. Finally, tighten completely using included Allen wrench.

5 STEP 4 Adjust Angles and Height STEP 4A Adjust Level Utilizing the leveling bubble, ensure End Clamp is level. If desired, arms can be adjusted to desired angle, in or out of center, by loosening Z-knob, adjust to desired angle, then tighten. STEP 4B Set Height Set and/or change height by installing Memory Collar at desired height (use included Allen wrench to tighten). STEP 4C Adjust Angle Adjust angle of Support Arm by loosening Z-knob, adjust to desired angle, then tighten. Page 5

6 A. B. C. Included Parts: A. Two (2) Support Arms B. Two (2) Riser Tubes C. Two (2) Memory Collar D. Two (2) End Clamps E. Two (2) Z-knobs F. Two (2) Washers G. Two (2) Small Springs H. Two (2) Nuts Included Tool: I. One (1) Allen Wrench Other Tool needed: J. One (1) Flathead Screwdriver (Not Included ) D. E. F. G. H. I. Page 6

7 IQ-3000 with Second Tier Pro V-Stand Pro with Second Tier Pro

8 Second Tier Pro Part Name: VSIQ-200B Part Number: For Use With: V-Stand Pro, IQ-3000 Height: 8.75" " Tube Length: 15.25" Weight: 5.5 lbs. Nombre de la pieza: VSIQ-200B Número de la pieza: Para usar con V-Stand Pro IQ-3000 Altura: 222mm - 470mm Longitud de tubo: 387mm Peso: 2.5 kg Teilebezeichnung: VSIQ-200B Artikelnummer: Zur Benutzung mit< V-Stand Pro, IQ-3000 Platzbedarf zusammengeklappt: 222mm - 470mm Rohrlänge: 387mm Gewicht: 2.5 kg Nom de la pièce : VSIQ-200B Numéro de la pièce : Compatibilité : V-Stand Pro, IQ-3000 Hauteur : 222mm - 470mm Longueur du tube : 387mm Poids : 2.5 kg Visit ultimatesupport.com to read full warranty details & to register for warranty Copyright 2015, Ultimate Support Systems. All Rights Reserved