FOR WALL MOUNT COMBINATION ARMS

Transcription

1 INSTALLATION MANUAL FOR WALL MOUNT COMBINATION ARMS LIGHT DUTY ARMS HEAVY DUTY ARMS KEYBOARD TRAY VERSION Weight Capacity 4-20 lbs KEYBOARD TRAY VERSION Weight Capacity 8-40 lbs WORKSTATION VERSION Weight Capacity 6-18 lbs WORKSTATION VERSION Weight Capacity lbs LAPTOP VERSION Weight Capacity 6-20 lbs DUAL SCREEN VERSION Weight Capacity lbs FXLT180 Rev. K

2 TABLE OF CONTENTS Tools / Installation Warnings / Disclaimer / Safety Warning / Adjustment Notification...3 Mounting Height...4 How to Install s...5 Mounting Surface Optional Pivot Limiter...8 Optional Extension Arm...9 Optional Extension Arm with Pivot Limiter...9 Main Arm Installation - Light Duty Arms Installation direct to Wall Ear Installation with Pivot Limiter Installation with Extension Arm Main Arm Installation - Heavy Duty Arms Installation direct to Wall Ear Installation with Pivot Limiter Installation with Extension Arm Monitor or Laptop Installation Cable Management - Light & Heavy Duty Arms Optional Extension Arm - Light & Heavy Duty Arms Counter Balancing the Arm - Light & Heavy Duty Arms Accessory Track Mount Installation Small Form Factor CPU Large Form Factor CPU Enclosed CPU Scanner Mount Accessory VESA Mount Installation Accessory Drop Kit Installation Adjustment Guide TOOLS REQUIRED Allen Wrenches: 1/4, 3/8, 3/16, 1/8, 5/16, and 5/32 Socket Wrench: 7/16 Drill Bit: 1/8 and 1/2 INSTALLATION WARNINGS: Read the entire instruction manual before beginning any installation or assembly. The installer must verify that the entire wall safely supports the combined weight of all the attached equipment and hardware. Improper installation of this product may cause extensive property damage or serious personal injury, either during or after installation. DISCLAIMER: The manufacturer and/or distributor will bear no responsibility for any damages of any kind arising from any improper installation of this product. Because wall construction varies widely and the ultimate method of mounting/installing is out of the manufacturers or distributors control, it is imperative that the installer consult with local engineering, architectural, or construction personnel to ensure the wall is constructed properly to code and will handle the applied load. Through improper installation or excessive applied load the monitor and mount can be pulled out of the wall by force, taking with it a large section of drywall. In no way will the manufacturer or distributor be held liable for any damage to the monitor, property or personal injury should an outside force either intentionally or unintentional be applied to the monitor or monitor mounting bracket causing it to pull off the wall. SAFETY WARNING: California installations may require specific anchorage and additional supports. Check with local authorities for codes in your area. Other seismic states will have similar regulations. Prior to drilling verify the location of any electrical wiring with in the wall. An electrical short can kill or create serious injury and fire hazard both during and after installation. MENT NOTIFICATION: Routine maintenance checks and adjustments are suggested to properly support the quality and optimal performance of this product. Refer to adjustment suggestions on last page of booklet or contact your distributor for further detailed information. Over tightening of bolts during installation or adjustments may cause damage to the product ultimately affecting the function. 2 3

3 MOUNTING HEIGHT HOW TO INSTALL TOGGLERS The track assembly is shipped with the wall ear installed at a suggested height. You may place the wall ear in any desired location on the track, providing you are installing directly to a stud center. If you are installing into drywall, then the wall ear must be positioned on the bottom lower half of the track. WALL TRACK Use a level and ensure track is flush, flat and snug to the wall. INSTALL TOGGLER BOLTS 1/2 WALL EAR Loosen, but do not remove 4 corner bolts Place in desired position Level and tighten bolts We recommend having the wall ear installed at the following heights which comfortably accommodates the majority of users in seated or standing positions. 28 FROM FLOOR TO BOTTOM OF WALL EAR 25 FROM FLOOR TO BOTTOM OF WALL EAR Use bolts provided to secure track to the wall. Refer to the reference guide on pages 6 and Configurations without an extension arm Configurations with an extension arm Some configurations will be supplied without any track, however a wall ear is still supplied. This version is a universal mounting solution and is intended to be installed into existing pre-installed compatible tracks.! Because wall construction varies widely and the ultimate method of mounting/installing is out of the manufacturers or distributors control, it is imperative that the installer consult with local engineering, architectural, or construction personnel to ensure the wall is constructed properly and to code to handle the applied load. The installer must verify that the entire wall will safely support the combined weight of all the attached equipment and hardware. The installed must verify that the existing wall track has been properly installed and maintained OR 4 5

4 MOUNTING SURFACE DIRECT TO DRYWALL STEEL STUD CONCRETE BLOCK WOOD STUD CONCRETE WALL (solid) TOGGLER TOGGLER TOGGLER 32 TRACK - 10 outer holes 48 TRACK - 10 outer holes 32 TRACK - 5 inner holes 48 TRACK - 4 inner holes 32 TRACK - 5 inner holes 48 TRACK - 4 inner holes 32 TRACK - 5 inner holes 48 TRACK - 4 inner holes NOT 32 TRACK - 5 inner holes 48 TRACK - 4 inner holes NOT 2 Nominal Concrete Blocks 2 Nominal Minimum 2 x 4 24ga. Steel Stud 4 Nominal Mortar Bed Minimum 2 x 4 Wood Stud 4 Nominal Concrete Slab 3/16 Concrete Screw #12 x 3 lg. Wood Screw 1-3/4 Min. Screw Embedment 2-1/2 Min. Penetration #12 x 3 lg. Wood Screw 2 1/2 Min. Hole Depth 3/16 Concrete Screw Minimum 2 x 4 Wood Stud Concrete Block Concrete Slab Minimum 2 x 4 24ga. Steel Stud Mortar Bed 3/16 x 2-1/4 lg. Min. Tapcon Concrete Screws to pass through the and into Ø.1902 pre drilled holes. NOTE: Bolts are to be placed in the horizontal center of the 2 x 4 Steel Stud. NOTE: Bolts must pass through concrete block. Bolts must not pass through mortar bed betwween blocks nor through the web within the blocks. When attaching to concrete blocks, only one bolt per cell allowed. NOTE: Screws are to be placed in the horizontal center and must penetrate at least 2-1/2 into the wood stud. NOTE: Pre drilled holes to be created using Tapcon drill bit for 3/16 x2-1/4 lg. concrete screws to a Min. hole depth of 2-1/2 into concrete slab. 6 Installation Instructions: FLUSH WALL MOUNT SYSTEMS 7

5 OPTIONAL ITEMS OPTIONAL ITEMS These items are to be installed before the main arm. OPTIONAL PIVOT LIMITER Installation direct to Wall Ear. This is an optional item and not included in all configurations. For further information please contact your distributor. OPTIONAL EXTENSION ARM Installation direct to Wall Ear. This is an optional item and not included in all configurations. For further information please contact your distributor. TENSION OPTIONAL EXTENSION ARM INSTALLATION WITH PIVOT LIMITER Installation direct to Wall Ear. These are optional items and not included in all configurations. For further information please contact your distributor. - Install optional arm to pivot limiter first before height adjustable arm. 90 Stop with Extension Arm 90 Stop without Extension Arm 70 Stop of Rotation TENSION 50 Stop of Rotation 30 Stop of Rotation 0 Stop of Rotation (arm will be locked perpendicular to wall) 8 Installation Instructions: FLUSH WALL MOUNT SYSTEMS 9

6 MAIN ARM INSTALLATION - Light Duty Arms MAIN ARM INSTALLATION - Heavy Duty Arms INSTALLATION DIRECT TO WALL EAR INSTALLATION DIRECT TO WALL EAR TENSION WALL EAR WALL EAR INSTALLATION WITH PIVOT LIMITER INSTALLATION WITH PIVOT LIMITER TENSION TENSION INSTALLATION WITH EXTENSION ARM INSTALLATION WITH EXTENSION ARM TENSION TENSION EXTENSION ARM TENSION EXTENSION ARM 10 Installation Instructions: FLUSH WALL MOUNT SYSTEMS 11

7 MONITOR OR LAPTOP INSTALLATION There are two different lengths of screws provided to attach the monitor to the VESA plate. Do not overtighten mounting screws. COUNTER BALANCING THE ARM Once all after sale technology is installed perform the following adjustments to ensure the arm raises and lowers as and does not freely drift up or droop down. LIGHT DUTY ARM Pull bar back, put laptop in place. Return bar and secure with lock. Use knob to secure lock nut. Two positions provided for rear lock bar 3/16" CABLE MANAGEMENT - Light Duty Arm CABLE MANAGEMENT - Heavy Duty Arm TENSION ATTENTION: Arm must be held in the upright position prior to making adjustments. HEAVY DUTY ARM Lower cover is removed to allow cable feed, then replaced OPTIONAL EXTENSION ARM - Light Duty Arm OPTIONAL EXTENSION ARM - Heavy Duty Arm 3/8" Remove botls TENSION ATTENTION: Arm must be held in the downward position prior to making adjustments. 12 Installation Instructions: FLUSH WALL MOUNT SYSTEMS Installation Instructions: FLUSH WALL MOUNT SYSTEMS 13

8 ACCESSORY TRACK MOUNT INSTALLATION These are optional items and not included in all configurations. ACCESSORY VESA MOUNT INSTALLATION These are optional items and not included in all configurations. VESA SCANNER MOUNT GRAB HANDLE VESA MOUNT SMALL FORM FACTOR CPU LARGE FORM FACTOR CPU ENCLOSED CPU SCANNER MOUNT All track mount accessories may be installed directly to wall structures by following mounting surface directions on page 6 and 7. Use the 4 outer most holes and appropriate hardware (not included). ACCESSORY DROP KIT INSTALLATION These are optional items and not included in all configurations. HOW TO INSTALL ONTO THE TRACK Remove the end cap at one end of the track slider. Slide the CPU or Scanner carriage onto the track. T-Nuts must engage edge of track. Tighten fully and test the CPU Holder remains in place prior to installing any technology. COMES WITH: Drop Tube Lock Washer Allen Drive Bolt Drop Tube Loosen and remove bolt and lock washer from keyboard platform assembly. NOTE: Firmly hold on to keyboard platform assembly while removing bolt from keyboard plate. Disassemble Assemble Some disassembly may be to access mounting bolts. Replace the end cap. Assemble and secure all components. Bottom of Monitor Arm DO NOT LOSE! Keyboard Plate Lock washer Bolt Drop Tube 7/32 Allen Wrench needed Keyboard Plate Lock washer Bolt 5/16 Allen Wrench needed 14 Installation Instructions: FLUSH WALL MOUNT SYSTEMS Installation Instructions: FLUSH WALL MOUNT SYSTEMS 15

9 MENT GUIDE Once all after sale technology is installed perform the following adjustments to ensure the arm raises and lowers as and does not freely drift up or droop down. ARM MENT - Counterbalance LIGHT DUTY ARM HEAVY DUTY ARM TENSION 5/16" Allen wrench needed 3/8" Allen wrench needed ARM MENT - Leveling (Left to Right) ATTENTION: Arm must be in the lowest position and swiveled 90 to the track when adjusted. NOTE: The level has been factory set. To adjust leveling bolt remove the plug and use 5/32" Allen wrench TENSION FOR WORSTATION/KEYBOARD FLIP Use 3/16 allen wrench for level adjustment KEYBOARD TRAY ANGLE Use 3/16 Allen wrench & 7/16 Socket Turn set screw to level keyboard tray (use 1/8 Allen wrench) TENSION MENT - Monitor Tilt Turn set screw to level keyboard tray (use 1/8 Allen wrench) TENSION MENT - Left to Right Movement At the wall At the Extension Arm Joint Remove caps Adjustable monitor tilt tension is PRE-SET. Adjust if with 3/16" Allen wrench and 7/16 Socket. 5/16 Allen wrench needed 5/16 Allen wrench needed RECOMMENDED FIELD MENT: If any resistance is felt in positioning the workstation from the left to the right please make the following adjustment. 1. Loosen the bolt located under the workstation/keyboard tray 2. Re-align the pivot pin installed on the keyboard plate with the slot on the underside of the LCD mounting system. This may be achieved by simply moving the two joining components slightly forward or back. 3. Tighten the bolt and washers in the appropriate position. Tighten until desired friction is achieved. Do not over tighten. FXLT180 Rev. K