Inverter Duty AC Motors

Transcription

1 inverter_duty_ac_motors.fm Page 225 Tuesday, December 17, :12 PM RPM AC RPM III Medium DC Motors Index 225

2 Index RPM III Medium DC Motors RPM AC Inverter Duty Vector Inverter Duty Totally Enclosed - IP44, Washdown - IP55 Electrical Characteristics Key Information Phase: 3 Duty Cycle: Continuous Definitions: Frequency: 60 Hz Insulation: Class F These motors have a special inverter duty design not Ambient: 40 Degrees C Temp. Rise: Class B covered by EPAct efficiency levels Service Factor: 1.0 Application Information For variable speed 1000:1 constant torque applications T Frames IP44 Materials: Conduit Box: Bearing Type: Bearing Protection: Shaft Material: Nameplate Material: Drain Type & Location: Additional Features: 56T - 180T Frames IP55 Construction Features Steel frame and conduit box (56 frames). Aluminum frame and conduit box ( frames). End shields are aluminum. Oversized, top mounted with F1 & F2 lead outlets Double shielded ball High strength carbon steel Adhesive Mylar Weep holes in both end shields Includes 3 NC thermostats Materials: Steel frame (56 frames). Aluminum frame ( frames). Conduit box is cast aluminum. End shields are cast iron. Conduit Box: Oversized, top mounted with F1 & F2 lead outlets Bearing Type: Double sealed ball Bearing Protection: Lip seal Shaft Material: 300 Stainless steel Nameplate Material: Adhesive Mylar Drain Type & Location: T-drains Additional Features: Includes 3 NC thermostats Warranty (From Date Of Manufacture / From Date Of Installation): (24/12) Nameplate Agency Approvals: CE, CSA, UR 226

3 Vector Inverter Duty Totally Enclosed - IP44, Washdown - IP55 C-Face Foot Mounted 1/3-5 HP With Encoder HP 1/3 1/2 3/ Speed RPM Base CHP Voltage Frame Enclosure Number C-Face Foot Mounted 1/3-5 HP Without Encoder HP For encoder kits # K00T0002 (H-20) and K00T0005 (SL56) see RPM accessories page See stock modifications for installing encoder kits Norm. Stock Notes Dimension Sheet /460 FB56C TENV P56H5302 $1,450 REM03 Y /460 FB56C TENV P56H5305 1,480 REM03 Y /460 FB56C TENV P56H5301 1,460 REM03 Y /460 FB56C TENV P56H5304 1,510 REM03 Y /460 FB56C TENV P56H5300 1,490 REM03 Y /460 FB56C TENV P56H5303 1,540 REM03 Y /460 WC143TC TENV P14A5800 1,746 REM03 Y /460 WC143TC TENV P14A5803 1,600 REM03 Y /460 WC143TC TENV P14A5801 1,806 REM03 Y /460 WC145TC TENV P14A5804 1,655 REM03 Y /460 WD145TC TENV P14A5802 1,804 REM03 Y /460 WD145TC TENV P14A5805 1,675 REM03 Y /460 WE182TC TENV P18A6101 2,031 REM03 Y /460 WE182TC TENV P18A6103 1,880 REM03 Y /460 WE184TC TEBC P18A6102 2,503 REM03 Y /460 WE184TC TEBC P18A6104 2,345 REM03 Y Synch RPM Voltage Frame Enclosure Number Norm. Stock Notes Dimension Sheet /460 FB56C TENV P56H6302 $343 RPMST N / /460 FB56C TENV P56H RPMST Y /460 FB56C TENV P56H RPMST N /460 FB56C TENV P56H RPMST N / /460 FB56C TENV P56H RPMST Y /460 FB56C TENV P56H RPMST N /460 FB56C TENV P56H RPMST N / /460 FB56C TENV P56H RPMST Y /460 FC56C TENV P56H RPMST N /460 WC143TC TENV P14A RPMST N /460 WC143TC TENV P14A RPMST Y /460 WC143TC TENV P14A RPMST N /460 WC143TC TENV P14A RPMST N /460 WC143TC TENV P14A RPMST Y /460 WE145TC TENV P14A RPMST N /460 WD145TC TENV P14A RPMST N /460 WD145TC TENV P14A RPMST Y /460 WE182TC TENV P18A RPMST N /460 WE182TC TENV P18A RPMST Y /460 WE184TC TEBC P18A RPMST N /460 WE184TC TEBC P18A RPMST Y Inverter capable. See page 14 Approx. Wt. (lb.) Approx. Wt. (lb) RPM AC RPM III Medium DC Motors Index 227

4 Index RPM III Medium DC Motors RPM AC Inverter Duty Vector Inverter Duty Totally Enclosed - IP44, Washdown - IP55 C-Face Foot Mounted 1/3-3 HP Washdown With Encoder HP 1/3 1/2 3/ Synch RPM Voltage Frame Enclosure Number C-Face Foot Mounted 1/3-3 HP Washdown Without Encoder For encoder kits # K00T0002 (H-20) and K00T0005 (SL56) see RPM accessories page See stock modifications for installing encoder kits Norm. Stock Notes Dimension Sheet /460 FB56C TENV-EZ P56H5322 $1,590 REM03 N /460 FB56C TENV-EZ P56H5325 1,620 REM03 N /460 FB56C TENV-EZ P56H5321 1,600 REM03 N /460 FB56C TENV-EZ P56H5324 1,650 REM03 Y /460 FB56C TENV-EZ P56H5320 1,630 REM03 N /460 FB56C TENV-EZ P56H5323 1,680 REM03 N /460 WC143TC TENV-EZ P14A5820 1,886 REM03 N /460 WC143TC TENV-EZ P14A5823 1,740 REM03 Y /460 WD143TC TENV-EZ P14A5821 1,946 REM03 N /460 WC143TC TENV-EZ P14A5824 1,795 REM03 Y /460 WE143TC TENV-EZ P14A5822 1,944 REM03 N /460 WD143TC TENV-EZ P14A5825 1,815 REM03 Y /460 WE182TC TENV-EZ P18A6121 2,171 REM03 N /460 WE182TC TENV-EZ P18A6123 2,485 REM03 Y Approx. Wt. (lb) HP Synch Norm. Dimensions Approx. RPM Voltage Frame Enclosure Number Stock Notes Sheet Wt. (lb.) /460 FB56C TENV-EZ P56H6322 $483 RPMST N / /460 FB56C TENV-EZ P56H RPMST N /460 FB56C TENV-EZ P56H RPMST N /460 FB56C TENV-EZ P56H RPMST N / /460 FB56C TENV-EZ P56H RPMST N /460 FB56C TENV-EZ P56H RPMST N /460 FB56C TENV-EZ P56H RPMST N / /460 FB56C TENV-EZ P56H RPMST N /460 FB56C TENV-EZ P56H RPMST N /460 WC143TC TENV-EZ P14A RPMST N /460 WC143TC TENV-EZ P14A RPMST Y /460 WD143TC TENV-EZ P14A RPMST N /460 WD143TC TENV-EZ P14A RPMST N / /460 WC143TC TENV-EZ P14A RPMST Y /460 WE145TC TENV-EZ P14A RPMST N /460 WE145TC TENV-EZ P14A RPMST N /460 WD145TC TENV-EZ P14A RPMST Y /460 WE182TC TENV-EZ P18A RPMST N /460 WE182TC TENV-EZ P18A RPMST Y Inverter capable. See page

5 Vector Inverter Duty Totally Enclosed - IP44, Washdown - IP55 Encoder Kits The following kits include encoder and all mounting hardware with coupling. New blower is required for TEBC. Encoder Ratings: All encoder kits are rated as follows: single output, 1024 PPR, two channel quadrature output (A and B) with complementary outputs, 5-15 VDC input. SMALL RPMAC TENV / Coupled Bearingless TEBC Dynapar H20 Lakeshore SL56 (2) Frame Size Order Order Number Number 56, 140, K00T0002 $800 RPMAC W180T K00T0003 (1) 400 RPMAC K00T0005 $1,500 RPMAC (1) New blower required for H20 when used with TEBC enclosure (2) Cannot be used on TEFC enclosure RPM AC RPM III Medium DC Motors Index 229

6 Index RPM III Medium DC Motors RPM AC Inverter Duty Explosion Proof - Extra Tough - Inverter Duty Totally Enclosed - IP54 Electrical Characteristics Key Information Phase: 3 Duty Cycle: Continuous Definitions: Frequency: 60 Hz Insulation: Class F EMT = E-Master motors that meet EPAct efficiencies Ambient: 40 Degrees C Temp. Rise: Class B XET = Premium efficient motors that exceed EPAct Service Factor: 1.0 efficiency levels Warranty (From Date Of Manufacture / From Date Of Installation): EMT (24/12), XET (36/24) Application Information Nameplate Agency Approvals: General purpose industrial applications containing hazardous gas, vapor, dust fibers, constant torque, Hz. CSA, UL continuous constant HP (UL file E6881) T Frames C-Face Foot Mounted 1/3-2 HP Construction Features UL ing Division 1 Class 1 Groups C & D, Class 2 Groups F & G, T3C Materials: Plate steel frame and fan cover, cast iron conduit box and end shields Conduit Box: F1 mounted Bearing Type: Double sealed ball bearings Bearing Protection: External slinger Shaft Material: 400 series stainless steel Nameplate Material: Stainless steel Drain Type & Location: Additional Features: HP 1/3 1/2 3/ HP and lower 56 frame motors are thermally protected with an auto thermal. 1HP and higher 140 frame motors are thermally protected with thermostats. Synch RPM Voltage Frame Enclosure Number * Stock modifications are not available on explosion proof motors. See modification catalog. - Inverter capable. See page 14 Norm. Stock Notes Dimension Sheet /460 HM56C FCXP-EMT P56X4070 $693 REM03 Y /460 HM56C FCXP-EMT P56X REM03 Y /460 HB56C FCXP-EMT P56X REM03 Y /460 HB56C FCXP-EMT P56X REM03 Y /460 HM56C FCXP-EMT P56X REM03 Y /460 HK56C FCXP-EMT P56X REM03 Y /460 HB56C FCXP-EMT P56X REM03 Y /460 HK56C FCXP-EMT P56X REM03 Y /460 HK143TC FCXP-XET P14X RXM03 Y /460 HB143TC FCXP-XET P14X RXM03 Y /460 HB143TC FCXP-XET P14X RXM03 Y /460 HD145TC FCXP-XET P14X RXM03 Y /460 HK143TC FCXP-XET P14X RXM03 Y /460 HK145TC FCXP-XET P14X RXM03 Y /460 HC145TC FCXP-XET P14X9132 1,050 RXM03 Y /460 HJ145TC FCXPXET P14X RXM03 Y Approx. Wt. (lb) 230

7 LV (Low Voltage) Inverter Duty Totally Enclosed - IP44 Electrical Characteristics Key Information Phase: 3 Duty Cycle: Continuous Definitions: Frequency: 60 Hz Insulation: Class F+ TEFC = E-Master motors that meet EPAct efficiencies Ambient: 40 Degrees C Temp. Rise: Class B Warranty (From Date Of Manufacture / From Date Of Installation): Service Factor: 1.15 (24/12) Application Information Nameplate Agency Approvals: CE, CSA, UL Designed for optimized performance from a 115/230 volt single phase input - three phase output variable frequency controller. 56 Frames Materials: Conduit Box: Bearing Type: Bearing Protection: Shaft Material: Nameplate Material: Drain Type & Location: C-Face Foot Mounted 1/3-1 HP HP Construction Features Rolled steel frame, conduit box and fan cover, Aluminum end shields Oversized, top mounted with F1 & F2 lead outlets Double shielded ball bearings High strength carbon steel Mylar Weep hole in both end shields Synch RPM Voltage Frame Enclosure Number 1/ /230 FB56C TEFC P56X1426 $262 REM01 Y 24 1/ /230 FB56C TEFC P56X REM01 Y 28 3/ /230 FK56C TEFC P56X REM01 Y /230 FK56C TEFC P56X REM01 Y 32 - Inverter capable. See page 14 Norm. Stock Notes Approx. Wt. (lb) RPM AC RPM III Medium DC Motors Index 231

8 Index RPM III Medium DC Motors RPM AC Inverter Duty Inverter Duty GENERAL PRODUCT DESCRIPTION The V*S Master motor, like the RPM AC motor, was designed from the beginning to be a Variable Speed Inverter Duty motor. It is not a fixed speed motor design that has been re-rated to be an Inverter Duty motor. All V*S Master motors are designed to operate from zero speed to base speed with full load current and torque below the class F temperature rise. Each V*S Master has three thermostats, one per phase, to provide Inverter Duty thermal protection. The V*S Master 1800 rpm, 1200 rpm and 900 rpm motors truly provide the performance of a blower-cooled motor in a TEFC enclosure. This means that the customer does not need to purchase and mount a blower motor starter or install threephase power leads to the blower motor. V*S Master Features 1000:1 Constant Torque - This means that the V*S Master is designed to operate from zero to base speed continuously with full load current and torque. The V*S Master TEFC and TENV motors are designed to draw nameplate current continuously at zero speed without exceeding the class F temperature rise. The industry standard is to call this capability 1000:1 Constant Torque, some manufacturers identify this capability 1000:1 Constant Torque, some manufactures identify this capability as 2000:1, 3000:1, infinity:1, etc. All of these terms describe the same capability of the AC Motor, one is not better than another. Standard NEMA T Frames - V*S Master motors, 2 HP to 500 HP are all in standard NEMA frames (Larger motors are in above NEMA frames 447T through L449T). Cast Iron Frames - All V*S Master motors are in cast iron frames with cast iron end shields. Adding XT features also provides a cast iron fan cover and conduit box along with other XT features. 200% Overload Torque - Each V*S Master has an electrical design that will provide 200% overload torque for one minute from zero to base speed. Constant Horsepower - The standard V*S Master is designed to provide constant horsepower to 1.5 times base speed. Thermostats - Each V*S Master motor has three normally closed thermostats connected in series, one in each phase of the motor. One set of P1 and P2 leads is brought to the conduit box. If any of the thermostats opens, the P1 and P2 circuit opens. Encoder Provisions - Each V*S Master has encoder provisions as a standard feature, even if an encoder is not ordered with the motor. 232

9 Inverter Duty V*S Master Features (cont) Insulated Bearing - Every 440 frame (444T through L449T) has an opposite drive end insulated bearing as standard to reduce the chances of the bearings being damaged by shaft currents. In large motors (440 frames) it is quite common to have shaft currents caused by magnetic flux dissymmetry, one insulated bearing will usually protect against this source of shaft currents. Other modifications, such as Current Shield can be added to protect against other sources of shaft currents. Corona Free Insulation - Every V*S Master motor has Reliance Electric s Corona Free insulation system that exceeds the insulation requirements described in NEMA MG1-1998, part 31, for Definite Purpose, Inverter-Fed Polyphase motors. Class F Insulation - V*S Master motors have class F insulation and operate below class F temperature rise. Nearly all TEFC V*S Master motors operate with a class B rise over a 4:1 speed range. That means that most TEFC 1800-rpm motors will operate with a class B rise over a 450 rpm to 1800 rpm (covers most actual operating conditions) speed range. 40 C ambient - Standard on nameplate, many V*S Master motors are suitable for higher ambient temperatures with only a nameplate change. Continuous Duty - Contact Reliance Electric for different duty cycles 1.0 Service Factor - Because V*S Master motors are designed for Inverter Duty applications, not across-the-line designs, all designs have a 1.0 SF as standard on inverter power. Re-greaseable bearings - For longest life in severe duty applications, all V*S Master motors have re-greaseable bearings. Stainless Steel Nameplates - Every V*S Master motor has an Inverter Duty stainless steel nameplate with the electrical design number, magnetizing current, constant torque speed range, number of poles, rotor inertia, bearing numbers and other NEMA data. F1 Mounting - Conduit box location is F1 as standard on NEMA frame motors (IEC motors have conduit box on opposite side as standard). F2 or top mounted conduit boxes are available as a modification. Visit web site for additional Inverter Duty Motor information. Download the V*S Master Data Sheet, RAPS V*S Master motors are CSA, Canadian Standards Association, certified and carry the monogram on the nameplate. All accessories attached the motor must also carry their own CSA mark. Reliance Electric s file number for V*S Master motors is, LR7861. The European Committee for Electrotechnical Standardization defines compliance standards for the CE mark required on motors shipping to Europe. It is available upon request on all V*S Master motors. The V*S Master IEC motors carry the CE mark as standard. All accessories attached to the motor must also carry their own CE mark. V*S Master motors carry the Underwriters Laboratories, Inc., Recognized Component mark for electric motors used in ordinary locations (not explosion-proof). Reliance Electric s file number for V*S Master motors is, E RPM AC RPM III Medium DC Motors Index 233

10 Index RPM III Medium DC Motors RPM AC Inverter Duty Inverter Duty Optimum Pole Reliance Electric s Inverter Duty Motors are based on the use of optimum pole design. Unlike fixed speed motors, Inverter-Fed motors can have different base speeds based on different base frequencies. For example, a four-pole motor designed with a base frequency of 40 hertz and a base voltage of 460 vac will have a base synchronous speed of 1200 rpm. Reliance Electric selects the number of poles to be used on an Inverter Duty motor so that the torque density, speed range, efficiency, power factor, overload capability and acoustic noise can be optimized. Like the Inverter Duty RPM AC motor, most of the Inverter Duty V*S Master motors in frames 180T through 400T are four-pole designs, regardless of the base speed. The Inverter is set to match the motor nameplate, for example, 50 hp, 1200 rpm, 460 vac, 40 hertz, and 4 poles. On larger frames of Inverter Duty AC motors, many of the designs are six-pole, regardless of the base speed. This approach has also been used in Reliance Electric s DC Motor designs for years. Most of the DC motor ratings 500 hp and less are four-pole designs, regardless of the base speed. For more information on optimum pole design, go to Reliance Electric s web site, and print the white paper, Optimum Pole Configuration of A-C Induction Motors used on Adjustable Frequency Power Supplies, B

11 Inverter Duty AC Motor 1000:1 Constant Torque TEFC & TENV Features Cast Iron frame and end brackets Three normally closed thermostats, one per phase Shaft drilled and tapped for installation of stub shaft 200% overload torque for one minute below base speed Class F insulation Continuous Duty 40 C Ambient Inverter Duty - not for across the line operation See previous Product Pages for additional features HP HP Synch RPM Voltage Frame Enclosure Number Norm. Stock 460V AMPS Dimensions Sheet Approx. Wt. (lb.) / TC TENV P18G1187 $1,179 RVM22 Y / TC TENV P18G RVM22 Y / T TENV P21G3205 1,484 RVM22 N /460 L184TC TENV P18G1189 1,106 RVM22 Y /460 L215T TENV P21G3206 1,720 RVM22 N /460 L215TC TENV P21G1162 1,383 RVM22 Y / T TEFC P25G3205 2,170 RVM22 N / TC TENV P25G1152 1,664 RVM22 Y /460 L215TC TEFC P21G1164 1,605 RVM22 Y / T TEFC P25G3206 2,458 RVM22 N / TC TENV P25G1150 2,137 RVM22 Y T TEFC P28G3205 2,903 RVM22 N T TENV P28G3208 2,402 RVM22 N TC TEFC P25G1151 2,110 RVM22 Y T TEFC P28G3206 3,301 RVM22 N T TENV P32G3210 3,198 RVM22 N TC TEFC P28G1083 2,668 RVM22 Y T TEFC P32G3205 4,333 RVM22 N T TENV P32G3209 4,963 RVM22 N T TEFC P28G3207 2,813 RVM22 Y T TEFC P32G3206 5,303 RVM22 N T TENV P36G3209 6,063 RVM22 N T TEFC P32G3207 3,949 RVM22 Y T TEFC P36G3205 6,388 RVM22 N T TENV P40G3208 7,526 RVM22 N T TEFC P32G3208 4,826 RVM22 Y T TEFC P36G3206 7,913 RVM22 N T TEFC P36G3207 5,979 RVM22 Y T TEFC P40G3205 9,443 RVM22 N T TEFC P36G3208 7,489 RVM22 Y T TEFC P40G ,340 RVM22 N T TEFC P40G3207 9,680 RVM22 Y T TEFC P44G ,356 RVM22 N NOTE: For the current version of Inverter Duty Motor dimension sheets, connection diagrams, design curves, etc., visit RPM AC RPM III Medium DC Motors Index 235

12 Index RPM III Medium DC Motors RPM AC Inverter Duty Inverter Duty AC Motor 1000:1 Constant Torque TEFC & TENV HP cont HP Synch RPM Voltage Frame Enclosure Number Norm. Stock 460V AMPS Dimensions Sheet Approx. Wt. (lb.) T TEFC P44G3207 $12,015 RVM22 Y T TEFC P44G ,998 RVM22 N T TEFC P44G ,339 RVM22 Y T TEFC P44G ,502 RVM22 N T TEFC P44G ,990 RVM22 Y T TEFC P44G ,996 RVM22 N T TEFC P44G ,003 RVM22 Y T TEFC P44G ,800 RVM22 N T TEFC P44G ,014 RVM22 Y L449T TEFC P44G ,011 RVM22 N L449T TEFC P44G ,811 RVM22 N L449T TEFC P44G ,500 RVM22 N L449T TEFC P44G ,315 RVM22 N (1) L449T TEFC P44G ,680 RVM32 N NOTE: For the current version of Inverter Duty Motor dimension sheets, connection diagrams, design curves, etc., visit (1) - Rated only for 4:1 constant torque speed range VXS - Inverter Duty The VXS TEFC, TENV and TEBC motors have been replaced by the Inverter Duty TENV and TEFC V*S Master motor and/or the Inverter Duty RPM AC motor. Contact Rockwell Automation Sales Engineers representing DODGE and Reliance Electric brands of products for applications where the V*S Master nor the RPM AC motor provide a suitable functional replacement for the VXS motor. The TEFC Inverter Duty V*S Master gives you the performance of a TEBC motor, full load torque from 0 to base speed, without the motor mounted blower. 236

13 V*S Master Encoder Kits 60HP, TEFC, 364T with HS35 ENCODER Encoder With Mounting Kit - Requires Both Numbers Frame Enclosure Type Supply Voltage Output/PPR Encoder Mounting Kit 180T-250T TENV BEI HS35 5 to 15 vdc Single/1024 K99G32 $1,000 K18G22 $100 RVM22 180T-440T TEFC BEI HS35 5 to 15 vdc Single/1024 K99G32 1,000 K21G RVM22 180T-250T TENV BEI HS35 5 to 26 vdc Single/1024 K99G34 1,000 K18G RVM22 180T-440T TEFC BEI HS35 5 to 26 vdc Single/1024 K99G34 1,000 K21G RVM22 180T-250T TENV MagCoder HS35M 5 to 24 vdc Single/1024 K99G35 1,250 K21G RVM22 180T-440T TEFC MagCoder MS35M 5 to 24 vdc Single/1024 K99G35 1,250 K21G RVM22 180T-250T TENV Avtron M3 5 to 18 vdc Single/1024 K99G33 2,300 K18G RVM22 210T-440T TEFC Avtron M3 5 to 18 vdc Single/1024 K99G33 2,300 K21G RVM22 BEI HS35 - This is an optical hollow shaft encoder with a single output, 1024 ppr, that has two channel quadrature outputs (A and B) with complementary outputs and a marker pulse (Z). Two versions of the encoder are stocked, 5 to 15 vdc input and a 5 to 26 vdc input, both are rated for 70 degrees C ambient, 6000 rpm maximum and have a IP65 enclosure rating. This encoder comes with a protective cover as shown in the above picture. See BEI s web site for additional information, Avtron M3 - This is an optical hollow shaft encoder with a single output, 1024 ppr, that has two channel quadrature outputs (A and B) with complementary outputs and a marker pulse (Z). The encoder requires 5-18 vdc input and is rated for 85 degrees C ambient, 5000 rpm maximum and has a totally sealed, cast aluminum housing with polyurethane enamel paint. See Avtron s web site for additional information, MagCoder HS35M - The MagCoder HS35M is a hollow shaft encoder with a single output, 1024 ppr, that has two channel quadrature outputs (A and B) with complementary outputs and a marker pulse (Z). The encoder requires 5-26 vdc input and is rated for 80 degrees C ambient, 3600 rpm maximum and has a IP65 enclosure rating. The MagCoder uses magneto resistive technology which makes it immune to common contaminants. The MagCoder HS35M was previously identified as a LakeShore product, but is now manufactured by Danaher Controls which also makes DynaPar encoders. For more information on LakeShore or DynaPar encoders, see web site NOTES: For mounting of the above encoders and kits by Reliance Electric, see the Modification Center price pages of this section. See the Variable speed Catalog or the Configurator for a complete list of encoders available on production Inverter Duty AC motor orders. RPM AC RPM III Medium DC Motors Index 237

14 Index RPM III Medium DC Motors RPM AC Inverter Duty Inverter Duty Modification Center Ordering Instructions Before Entering an Order 1. Determine the proper stock model number to be modified and check availability. 2. Be sure the modifications required are available. 3. XP modifications are not available. See modification catalog. How to an Order 1. Record the list price of the required motor model number plus add all list modification adders and multiply it by the appropriate discount symbol. 2. Record total motor net. How and Where to Enter an Order Reliance Distributors: Can phone their orders to Rockwell Automation Reliance Electric Inside Sales Representative or send a fax to: Or for those not assigned an Inside Sales Representative, you may call the main switchboard at District Sales Engineers: May place orders to the Modification Centers via OMS. Cancellation or Changes to an Order To cancel an order for a motor after it is modified, but before it ships, a cancellation charge of double the modification charge will be invoiced to the customer. Any MOD order cancelled before modification is completed is subject to 25% cancellation charge. Once shipped, modified motors cannot be returned. Delivery Cycle The delivery cycle will be subject to the availability of stock motors and parts. The Modification Center is designed to process and ship units as quickly as possible; therefore, Hold for Approval and other similar conditions are not available on Modification Center orders. For best delivery results, check stock availability and reserve the motor prior to order entry. Typically, modifications will require 2 to 7 business days, once the order is entered. Orders for more than 5 units may require additional delivery time. Hours The Modification Centers are operated from 7 am to 3 pm Monday through Friday. 238

15 Inverter Duty Modification Center Modification Description Frame Enclosure 1. BEARINGS: (per set / per motor) Shielded bearings (specify double or single shielded bearing, Mfg. is Reliance Option) Adder Notes ALL $ ALL ALL ALL ALL Sealed bearings-convert to permanently lubricated sealed bearings 2. BRAKES: Mount double c-face DODGW DBSS brake kit to c-face motor Standard Enclosure 3 ft. lb. 56C. 140TC ALL NON XP 1,350 6 ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 1,900 Easy Clean (Washdown) Enclosure 3 ft. lb. 56C. 140TC ALL NON XP 1,600 6 ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 1, ft. lb. 56C. 140TC ALL NON XP 2, ft. lb. 56C. 140TC ALL NON XP 2, CONDUIT BOX: Mounting of stock box kits (price includes box): Convert to cast iron or oversize ALL ALL Auxiliary box attached to main conduit box ALL CONNECTIONS: Final connect dual to single voltage ALL ALL ALL COUPLING: Mount customer supplied finished bored 1/2 coupling - clearance ALL 280 fit only 6. DRAINS: One in each motor end bracket: Stainless steel T-drain ALL 690 Note: Mounting position must be specified e.g. F-1, W-1, etc. 7. DRIPCOVERS: Mounting of stock canopy kits (includes drip cover kits) This modification does not provide vertical lifting ENDSHIELDS: Note: Does not include seal, add seal modification, if required. Changing from std.end to C-face on drive end (C.I. N/A) 48,56,140 ALL 220 Changing from std. end to C-face with feet (Non-NEMA BA) ALL 550 Changing from std. end to C-face with feet (NEMA BA) ALL FAN COVER: (Cast Iron Fan Shroud and Conduit Box) TEFC TEFC TEFC 1, FRAME: Remove feet. (Note: add in conjunction with flange modification) Not returnable to stock 11. GREASE: Changing to special grease - based on availability / suitability: Mobil 28 or Aeroshell 7 low temperature or DC-44 (synthetic) high temperature grease * * Check Availability TENV TEFC TEFC TEFC TEFC ALL ALL ALL ALL ALL ALL ALL 1,110 RPM AC RPM III Medium DC Motors Index 239

16 Index RPM III Medium DC Motors RPM AC Inverter Duty 240 Inverter Duty Modification Center - cont Modification Description Frame Enclosure Adder 12. GREASE FITTINGS: Alemite 1610 or button head zerk fitting ALL $ GROUNDING: (All motors have provision for grounding) Clamp type in conduit box ALL INSULATION: (Addition of tropical, anti-fungus treatment to windings) ALL ALL ALL LEAD TERMINALS: Addition of eyelet - type lead terminals ALL 280 Compression type (Burndy, etc.) lead lugs ALL MOUNTING: (not available on L180T-L210T frames) F-1 to F-2/W6/W8/W5/W ALL ALL NAMEPLATES: Allows adding definite purpose nameplates or the addition of information. Characters of additional information will be available in 3/32 only. Over 25 characters will require an additional blank nameplate with the auxiliary nameplate charge added. Charges are per nameplate. Nameplates are stainless steel. Separate nameplate for customer data ALL 140 Additional data on motor nameplate ALL 140 Separately shipped re-rated nameplate for stock motor in the field ALL 420 (no CSA logo) Requires return of old nameplate. 18. SEALS: V-ring rubber slinger on drive end ALL SPACE HEATERS: (120, 240, 480 volt) Auxiliary box not included. See conduit boxes Mounting of standard strip heaters ALL ALL ALL ALL ENCODERS: Mounted on. All encoders are 1024 PPR, single quadrature output Series H-20 (K00T0002) 56, 140, WF180 TENV (RPMAC) 1,100 Series H-20 (K00T0002+K00T0003) WF180 TEBC (RPMAC) 1,600 Lake Shore SL56 (K00T0005) 56,140,WF180 TENV (only) 1,800 BEI hollow shaft HS TEFC & TENV 1,100 Avtron hollow shaft M TEFC & TENV 2,500 Lake Shore hollow shaft HS35M TEFC & TENV 1, TERMINAL BLOCK: IEC style terminal block or NEMA terminal strip in conduit box Limited to single voltage motors with three leads - specify voltage 22. THERMAL PROTECTION: Three normally closed (N.C.) thermostats, one per phase, included in all, except the 56 frame TEFC motors for single-phase inverters. * Check Availability NOTE: Under Enclosure, ALL does not include explosion proof (XP) enclosures TEFC TEFC TEFC TEFC 1,110 Notes