Series Rated / Fully Rated Tables. Lighting and Appliance Panelboards. Panelboard Special Features

Transcription

1 Table of Contents Section Panelboards NQ Panelboards Page -5, x Series Rated / Fully Rated Tables NQ -2, -42 NF -3 I-Line -3 Lighting and Appliance Panelboards NQ/NF Pricing Procedure -5 NQ Merchandised Lug Panelboards -6 Merchandised Breaker Panelboards -7 Merchandised 14-inch-wide Panelboards -8 Merchandised Accessories - QOB Branch Breakers -10 Factory Assembled Panelboards and Breakers -11 Factory Assembled Common Features -12 NF Merchandised Lugs Panelboards -13 Merchandised Breaker Panelboards -13 Merchandised Lug and Breaker Panelboards with -13 Merchandised Accessories -14 EDB, EGB, EJB Branch Breakers -15 Factory Assembled Panelboards -16 Factory Assembled Common Features -17 NQ/NF Column Width Merchandised Single Row (Column Width) Panelboards Factory Assembled Single Row (Column Width) Panelboards NF Panelboards Page -13 I-Line Panelboards Page -20 Power Distribution Panelboards Breaker Type I-Line/QMB Pricing Procedure -20 I-Line Merchandised Panelboards (HCN, HCM, HCP-SU) -21 Merchandised Panelboards (HCP, HCR-U) -22 Merchandised Accessories -23 Breakers -24 F-frame Breakers -24 Q-frame Breakers -25 H-frame and J-frame Breakers -26 K-frame Breakers -27 L-frame Breakers -28 M-frame Breakers -2 P-frame and R-frame Breakers -30 Factory Assembled Pricing -31 Factory Assembled Branch Breakers -32 Factory Assembled Common Features -34 Power Distribution PanelboardsFusible Type QMB Replacement Switches -35 Factory Assembled Pricing -36 Factory Assembled SPD Units -37 Panelboard Special Features QMB Panelboards Page -35 Factory Assembled Modifications -38 Terminal Data Schneider Electric -1

2 Series s NQ Panelboards Class This page contains UL Tested and Certified series combination ratings for panelboards. These ratings apply to either an integral main located in the same enclosure or a remote main located in a separate enclosure. Table.1: Maximum System Voltage AC ab NQ Series Connected Breaker s (RMS Symmetrical) Maximum Short Current Square D Brand Integral or Remote Breakers and Remote Fuses Square D Brand Branch Breaker Designation and Allowable Ampere Ranges cdef Type 1 Pole 2 Pole 3 Pole NOTE: Table.1 NQ Series Connected Breaker s table has moved to page -42 and page Schneider Electric

3 Schneider Electric Series s This page contains UL Tested and Certified series combination ratings for panelboards. These ratings apply to either an integral main located in the same enclosure or a remote main located in a separate enclosure. Table.2: Maximum Max. System Short Voltage, AC a Current. NF Series Connected Breaker s (RMS Symmetrical) Square D Brand Integral or Remote Breakers and Remote Fuses Square D Brand Branch Breaker Designation and Allowable Ampere Ranges EG, FH, FG, KH, LH, MH, MX, HG, JG, DG EDB, EDB-EPD 65,000 LG EDB EG ECB-G3 EJ, FC, FJ, KC, LC, HJ, JJ EDB, EDB-EPD, EGB ,000 DJ, LJ EDB, EGB 120/240 EJ, FC, KC, HJ, JJ ECB-G ,000 HL, JL EDB, EDB-EPD, EGB, ECB-G3 FI, KI, LI, LXI, HR, JR, LR EDB, EDB-EPD, EGB, EJB 200,000 FI, KI, HR, JR ECB-G3 Class J or T (600 V) 200 A Max Fuses ECB-G3 35,000 EG, FG, KH, LH, HG, JG, DG, LG EG, HG, JG EDB, EDB-EPD ECB-G3 EJ, FC, FJ, KC, LC, LX, HJ, JJ, DJ EDB, EDB-EPD, EGB EJ, FC, KC, HJ, JJ ECB-G3 65,000 LJ EDB, EDB-EPD, EGB, EGB-EPD Y/277 LL EDB-EPD, EGB-EPD HL, JL EDB, EDB-EPD, EGB, EJB 100,000 DL, LL EDB, EGB, EJB 400 A Max Fuses EDB, EDB-EPD, EGB, EJB FI, KI, LI, LXI, HR, JR, LR EDB, EDB-EPD, EGB, EJB 200,000 FI, KI, HR, JR ECB-G3 200 A Max Fuses EDB, EDB-EPD, EGB, EJB, ECB-G3 18,000 HG, JG, MG, LG EDB EDB ( A) EJ, FI, KH, KI, LC, LE, LX, LI, LXI, HJ, JJ EDB, EGB 25,000 LJ EDB ( A), EGB ( A) LH (15 70 A) EDB, EGB 600Y/347 35,000 LC, LE, LX EDB, EGB, EJB HL, JL, EDB, EGB, EJB 50,000 LL EDB ( A), EGB ( A),EJB ( A) 65,000 FI, KI, HR, JR LI, LXI, LR EDB, EGB, EJB EJB 200,000 Class J or T (600 V) 200 A Max Fuses EDB, EGB, EJB Table.3: Maximum System Voltage AC a I-Line Series Connected Breaker s (RMS Symmetrical) Max. Short Current (RMS Symm.) Integral or Remote 2- or 3-pole Breaker Square D Brand Branch Breakers Designation Poles 42k MG FY 65k QG, LH FA, FDb k FJb, QJ QJ, LC FDb FA 1 LJ FH 200k LR FH, FY 208Y/ k QJ QJ, PH, PJ, RJ FA, FDb QD, QG 2, 3 35k MG FA 1 42k KA FDb 1, 2, 3 LA, MA HD, JD, QD 2, 3 50k MG FA MG FA (25 A Max.) 1 HG, JG FA, HD JG QG JD, QD FA, FDb, QD 2, 3 LH, MH, PA, PG, RG HD, JD, QD FGb, FH, MH, MX, PJ FDb 65k FC, KC, KH, LC, LH FDb, FGb 1, 2, 3 LH FA LH LA MG HD, JD, KA LG DG HD, JD, KA, LA, LD, MA FH, HD, JD, KA, LA, MA 2, 3 85k RL FH, KH 240 FC, KC, LC, LX FDb, FGb, FJ 1 PH, PJ, RJ QD, QG 2, 3 QJ FDb 2 FJb FDb FC, KC FA, FH, FDb, FGb, FJb LC, LX KC, LC, LX FH, FDb, FGb, FJb KA 2, 3 KC, LC KH 100k LC LA, LH, MG LC FA 1, 2, 3 HJ, JJ FA, FH, HD, HG JJ JD, JG LC, LX, MJ, PJ, RJ HD, HG, JD, JG MJ LJ LA, LH FH, HD, HG, JD, JG, KA, LA, LD, LG, MA, MG 2, 3 DJ FH, HD, HG, JD, JG, KA, LA, MA, MG RL RG HL, JL HD, HG, HJ, FA, H JL JD, JG, JJ PC, PH, PL, RL HD, HG, JD, JG k PC, PL, RL HH, JJ 2, 3 FI, KI, LI, LXI HD, HG, HJ KI, LI, LXI JD, JG, JJ Table.3: Maximum System Voltage AC a NF and I-Line Panelboards Class 2110 / Refer to 2110CT701 I-Line Series Connected Breaker s (RMS Symmetrical) (continued) Max. Short Current (RMS Symm.) Integral or Remote 2- or 3-pole Breaker Square D Brand Branch Breakers Designation FI, KI, LI, LXI FDb, FGb, FJ 1 FI, KI FA, FH, FC, FDb, FGb, FJb LI, LXI FH, FDb, FGb, FJb k LI FC KI, LI, LXI KA, QD, QG, QJ 2, 3 LI KC LR FH, HJ, QG, QJ HL, JJ, JL, LA, LH, QD, 18k LD FY 25k FH, KA FDb FGb, KH, LH FDb 35k DG FH, FY LG FH, FY FJb FDb FC, KC FA, FH, FY, FDb, FGb LC, LX (400 A Max.) FH 65k LC, LX (600 A Max.) FY, FDb, FGb 277 LJ DJ FH, FY FH, FY 1 LL FY 100k DL LL FH, FJb FH, FJb FI, KI FA, FH, FY, FDb, FGb, FJb HR FA, FJb, FY 200k JR LI, LXI (400 A Max.) FA, FJb, FY FH LI, LXI (600 A Max.) FY, FDb, FGb, FJb LR FH, FY 22k MG FA KH, LA, MA, MX, PA, PC, PX, PJ FH 30k LA, MA, PA, PC, PX KA LA, MA, PA HD, JD MG FA (25 A Max.), FH, KA MH, MX, PA HD, JD HG, JG FA, HD 35k JG LH, MG, PG, RG JD HD, JD LG FH, HD, JD, KA, LA, LD, MA DG FH, HD, JD, KA, LA, MA 42k MJ RL FH (25 A Max.) RG 50k MJ KA, KH FC, KC FA, FH HJ, JJ FA, FH, HD, HG JJ JD, JG LC, LI, LX, LXI HD, HG, JD, JG k LC, LX (400 A Max.) FH KC, LC, LX KA LC, LX LA LJ FH, HD, HG, JD, JG, KA, LA, LD, LG, MA DJ FH, HD, HG, JD, JG, KA, LA, MA 2, 3 HL, JL FA, FH, HD, HG, HJ JL JD, JG, JJ JR FA LI, LXI (600 A Max.) KA 100k LL FH, HD, HG, HJ, JD, JG, JJ, KA, LA, LD, LG, LJ, MA DL FH, HD, HG, HJ, JD, JG, JJ, KA, LA, MA PC, PH, PL, RL HJ, JJ RL RG FI, KI FA, FH, FC, HD, HG, HJ HR FA, HD, HG, HJ, HL JR HD, HG, HJ, HL, JD, JG, JJ, JL 200k KI JD, JG, JJ, KA LI FC, KA, KC, LA, HJ, HL, JJ, JL LR FH, HJ, HL, JJ, JL, LA, LH LXI KA, HJ, HL, JJ, JL 25k FH, KA FDb 35k FGb, KH, LH FDb FJb FDb 480Y/277 65k FC, KC FDb, FGb LC, LX (600 A Max.) FDb, FGb 200k FI, KI LI, LXI (600 A Max.) FDb, FGb, FJb FDb, FGb, FJb HG, JG FA, HD JG JD 18k LG HD, JD, LD MG, PG, RG HD, JD MG FA HJ, JJ FA, HD, HG 25k JJ LJ JD HD, HG, JD, JG, LD, LG, MA PJ, RJ MG k LC FH, HD, HG, HJ, JD, JG, JJ, LA HL, JL FA, HD, HG, HJ 2, 3 50k JL LL JD, JG, JJ HD, HG, HJ, JD, JG, JJ, LD, LG, LJ, MA PK HJ, JJ, MJ FI, KI HD, HG, HJ HR FA, HD, HG, HJ, HL 100k JR KI FA, HD, HG, HJ, HL, JD, JG, JJ, JL JD, JG, JJ KI, LI FH LI LA 18k MG FA (25 A max.) 600Y/347 25k MJ FA (30 A max.) 1 50k HL, JL FJ a Short circuit tests are conducted at % of the maximum rated voltage of the panelboard. b Obsolete. Contact your local Schneider Electric representative or distributor for the replacement circuit breaker. NOTE: LD, LG, LH, and LL breakers are only available in 3 pole configurations. -3 Poles

4 Series s Table.4: Fuse/I-Line Breaker Series Connected s Maximum System Max. Short Remote Fuse Voltage AC Current Maximum (RMS Symm.) Amperage Fuse Class 120/240 1Ø 208Y/ , , , , , , , ,000 I-Line Panelboards Class 2110 Square D Brand Branch Breakers Designation a A L, T (300 V) QD, QG 800 A T (600 V) QD, QG 600 A J, RK5 QD, QG 1200 A L, T (300 V) QD 800 A T (600 V) QD 600 A J, RK5 QD 1200 A L, T (300 V) QD, QG (2-pole) 800 A T (600 V) QD, QG (2-pole) J, RK5 QD, QG (2-pole) L, T (600 V) FA, FH, KA, KH, KC, LA, LH, MA, MH, MX, PG 600 A RK5 FH, KA, KH, LA, LH, MA, MH, MX, PG, HD, HG, HJ, HL, JD, JG, JJ, JL J HD, HG, HJ, HL, JD, JG, JJ, JL T (600 V) FH, KA, KH, LA, LH, MA, MH, MX, PG 800 A T (300 V) PG L FH,KA,KH,LA,LH,MA,MH,MX,PG L FH, KH, LA, LH, MA, MH, MX, PG 1200 A T (600 V) HD, HG, HJ, HL, JD, JG, JJ, JL 1600/2000 A L KH, MA, MH, MX, PG 4000 A L HD, HG, HJ, HL, JD, JG, JJ, JL J, T (600 V) FA( 3-pole only), FH, FC, KA, KH, KC, LA, LH, LC, MA,MH,MX,NA,NC,NX,PG,PJ,PL 600 A RK5 FH, FC, HD, HG, HJ, HL, JD, JG, JJ, JL KH, KC, LA, LH, LC, MA, MH, MX, NC, NX, PG, PJ, PL J HD, HG, HJ, HL, JD, JG, JJ, JL T (600 V) FH, FC, KA, KH, KC, LA, LH, LC, MA, MH, MX, NA, NC, NX, PG, PJ, PL 800 A T (300 V) PG, PJ, PL L FH,FC, KH, KC, LA, LH, LC, MA, MH, MX, NA, NC, NX, PG, PJ, PL L FC, KH, KC, LC, MA, MH, MX, NA, NC, NX, PG, PJ, PL 1200 A T (600 V) HD, HG, HJ, HL, JD, JG, JJ, JL 1600/2000 A L NA, NC, NX, PJ, PL 4000 A L HD, HG, HJ, HL, JD, JG, JJ, JL 400 A J, T (600 V) HD, HG, HJ, HL, JD, JG, JJ, JL J, RK5 HJ, HL, JJ, JL 600 A J, T (600 V) FC, KA, KH, KC, LA, LH, LC, MA, MH, MX, NA, PG, PJ RK5 FC, KA, KH, KC, LA, LH, LC, MA, MH, MX, NA, PG, PJ 800 A L, T (600 V) FC, KA, KH, KC, LA, LH, LC, MA, MH, MX, NA, PG, PJ L FC, KH, KC, LA, LH, LC, MA, MH, MX, NA, PG, PJ 1200 A T (600 V) HJ, HL, JJ, JL 1600 A L KC, LC, MA, MH, MX, NA, PG, PJ 2000 A L KC, LC, MH,MG, MJ, MX, NA, PG, PJ 4000 A L HJ, HL, JJ, JL 200 A RK5 HJ, HL J FA, FH, FC, HJ, HL, JJ, JL, KA, KH, KC, LA, LH, LC, 400 A MA,MH,MX,NA,NC,NX,PG,PJ, PL T(600V) FA, FH, FC, HJ, HL, JJ, JL, KA, KH, KC, LA, LH, MA, MH, MX, NA, NC, NX J FC, KA, KH, KC, LA, LH, LC, MA, MH, MX, MG, MJ, NA, NC, NX, PG, PJ, PL 600 A T (600V) KA, KH, KC, LA, LH, MA, MH, MX, NA, NC, NX RK5 KC, LA, LH, LC, MA, MH, MX, MG, MJ, NC, NX, PG, PJ, T (300 V) PG, PJ, PL 800 A T (600 V) KA, KH, KC, LA, LH, MA, MH, MX, MG, MJ, NA, NC, NX, PG, PJ, PL L KC, LA, LH, LC, MA, MH, MX, NA, NC, NX, PG, PJ, PL 1200 A L KC, LC, MA, MH, MX, MG, MJ, NA, NC, NX, PG, PJ, PL 1600/2000 A L NA, NC, NX 30 A CC HG, JG ( molded case switches ) 200 A J HD, HG, HJ, HL, JD, JG, JJ, JL 400 A J, T (600 V) HJ, HL, JJ, JL 600 A R MG, MJ 1200 A L MG, MJ 600 A J MG, MJ 800 A T (600 V) MG, MJ a Series rating valid for 2-pole or 3-pole circuit breakers. Note: The fuse used in this UL test is an envelope (umbrella) fuse. This fuse is designed as a worst case fuse. Thus, no matter what manufacturer s fuse is used, the Square D brand circuit breaker is protected. The line side fused switch may be in a separate enclosure or in the same enclosure as the loadside circuit breaker. A line side fused switch may be a submain, integral main, or remote main. A load side circuit breaker may be a branch, submain, or an integral main used on the load side of a remote main. This series combination short circuit current rating shall not exceed that of the line side fused switch. The charts apply to Square D brand load side circuit breakers only. However, the line side fuse ratings are independent of the fuse manufacturer. Not applicable to Corner Grounded Systems. Limiters used in Square D brand DSL and DSL II fused power circuit breakers are not class L fuses and do not have series ratings Schneider Electric

5 NQ and NF Panelboards Pricing Procedure and Examples Classes 1640 and 1670 / Refer to 1670CT0701, 1640CT0801 NQ and NF Merchandised Pricing Procedure 1. List circuit breakers required, either plug-on or bolt-on. See the appropriate Digest pages for catalog numbers. 2. Determine equivalent number of pole spaces required. 3. Select proper main lug interior (from page -6) or main lug interior and main circuit breaker adapter kit (from page -7) based on equivalent number of poles and ampere rating. Interiors include solid neutral and are field convertible to top-feed. 4. Select enclosure from appropriate page. Type 1Select box and front catalog number corresponding to interior catalog number. Type 3R, 5, 12Select enclosure. Interior trim kit for Type 3R, 5, 12 is included with the enclosure. 5. For complete price, add the component prices. Include panelboard accessories. 6. Apply appropriate discount schedule. NQ and NF Factory Assembled Pricing Procedure 1. Select Base Price for main lugs or main circuit breaker from the Base Price Table. Include equipment ground bar when required. 2. List Branch Breakers (either plug-on or bolt-on) and determine total spaces required. Select price from the Branch Breakers Table. Include space-only charge for future requirements. 3. If total spaces required exceeds the maximum listed, price as two or more panelboards and add price for sub-feed or feed-through lugs so installer can cable between sections. 4. Add price for special features from appropriate page. Contact your local Schneider Electric representative or distributor for additional special features. 5. For complete price, add all prices. Order by description. NOTE: Additional special price adders can be found in the Supplemental and Obsolescence Digest, Section Apply appropriate discount schedule. NQ Merchandised Pricing Example Table.5: 208Y/120 Vac, 3Ø4W, 10 ka SCCR, 225 A, MLO, Type-1, surface-mount, bolt-on, branch circuit breakers, main sub-feed lugs Branches Page No. Spaces (20) 20/1-10 (20) QOB two 40/2-10 two QOB two 30/3-10 two QOB Total A MLO Interior -6 NQ430L Box -6 MH32 Cover -6 NC32S 527. Sub-feed Lugs -6 NQSFL Total Price NQ Factory Assembled Pricing Example Table.7: 208Y/120 Vac, 3Ø4W, 10 ka SCCR, 225 A, MLO, Type-1, surface-mount, bolt-on, branch circuit breakers, main sub-feed lugs Item Page No. 225 A MLO Base Price (20) 20/1 Bolt-on two 40/2 Bolt-on two 30/3 Bolt-on Sub-feed Lugs Total Price NF Merchandised Pricing Example Table.6: 480Y/277 Vac, 3Ø4W, 25 ka SCCR, fully rated, copper bus, 100 A, main circuit breaker, Type 1, flush-mount, bolt-on, branch circuit breakers Branches Page No. No. Spaces (13) 20/1-15 EGB one 40/2-15 EGB one 50/3-15 EGB Total 18 circuit breaker adapter kit (less circuit breaker) -13 N150MH 780. circuit breaker 7-28 HGL A MLO Cu Bus Int. -13 NF418L1C Box -13 MH38 Cover -13 NC38F 54. Total Price NF Factory Assembled Pricing Example Table.8: 480Y/277 Vac, 3Ø4W, 25 ka SCCR, fully rated, copper bus, 250 A, main circuit breaker, Type 1, flush-mount, bolt-on, branch circuit breakers Item Page No. 250 A Breaker Base Price Copper bus adder (13) 20/ one 40/ one 50/ Total Price Schneider Electric Example pricing only Discount -5

6 NQ Merchandised Panelboards Table.: Pole Spaces s Lug InteriorsAccepts plug-on and bolt-on circuit breakers Total Price Interior Front and Enclosure Type 1 Type 3R, 5,12 20-inch-wide Cabinet gsingle Phase 3-Wire Interior Only (Order Branch Breakers Separately) NQ Lug Interiors240 Vac, 48 Vdc Class 1640 / Refer to 1640CT0801 Type 1 Enclosure Type 3R, 5, 12 Enclosure f Box 20 in. W x 5.75 in. D b Mono-Flat Front c Hinged Front Enclosure 20 in. W x 6.5 in. D No. a $Price No. No. No. No NQ18L MH26 NC26 ( ) 47. NC26( )HR 620. MH26WP NQ18L1C NQ30L MH32 NC32 ( ) 527. NC32( )HR 657. MH32WP NQ30L1C NQ30L MH32 NC32 ( ) 527. NC32( )HR 657. MH32WP NQ30L2C NQ42L MH38 NC38 ( ) 54. NC38( )HR 687. MH38WP NQ42L2C NQ72L d MH44 NC44 ( ) 663. NC44( )HR 830. MH44WP NQ72L2C NQ84L d MH50 NC50 ( ) 72. NC50( )HR 12. MH50WP NQ84L2C NQ30L NQ30L4C MH50 NC50V ( ) 72. NC50V( )HR 12. MH50WP NQ42L NQ42L4C d NQ84L4C 372. MH68 NC68V ( ) 48. NC68V( )HR MH68WP NQ30L6C MH50 NC50V ( ) 72. NC50V( )HR 12. MH62WPe / NQ42L6C d NQ84L6C MH68 NC68V ( ) 48. NC68V( )HR MH80WPe /80 20-inch-wide Cabinet g Three Phase 4-Wire NQ418L MH26 NC26 ( ) 47. NC26( )HR 620. MH26WP NQ418L1C NQ430L MH32 NC32 ( ) 527. NC32( )HR 657. MH32WP NQ430L1C NQ430L NQ430L2C 122. MH32 NC32 ( ) 527. NC32( )HR 657. MH32WP NQ442L NQ442L2C MH NQ454L NQ454L2C 14. NC38 ( ) 54. NC38( )HR 687. MH38WP d NQ472L NQ472L2C MH44 NC44 ( ) 663. NC44( )HR 830. MH44WP d NQ484L NQ484L2C MH50 NC50 ( ) 72. NC50( )HR 12. MH50WP NQ430L NQ430L4C 180. MH NQ442L NQ442L4C NC50V ( ) 72. NC50V( )HR 12. MH50WP d NQ472L NQ472L4C MH62 NC62V ( ) 887. NC62V( )HR 110. MH62WP d NQ484L4C MH68 NC68V ( ) 48. NC68V( )HR 1185 MH68WP NQ430L6C MH NQ442L6C NC50V ( ) 72. NC50V( )HR 12. MH62WPe /62 84d NQ484L6C MH68 NC68V ( ) 48. NC68V( )HR MH80WPe /80 a C suffix indicates copper bussing. b Embossed mounting holes add a 0.25-inch standoff to back of MH box. c Add F for flush mount, S for surface mount. d Use only if the Local Jurisdiction where this panelboard interior is being applied has adopted the 2008 NEC, which allows single panelboard interiors greater than 42 circuits. e When NEMA 3R, 5, or 12 enclosures are selected, an NQ12RDE kit should also be selected. See Table.1. f Enclosure includes trim kit. g For the NQ14-inch-wide panelboard offer, See Digest page -8. Height (In.) Schneider Electric PE1A Discount

7 NQ Merchandised Panelboards NQ Breaker Interiors240 Vac, 48 Vdc Class 1640 / Refer to 1640CT0801 Table.10: Pole Spaces s Breaker InteriorsWill accept plug-on and bolt-on circuit breakers Total Interior, Front, Box and Adapter Kit f Type 1 Type 3R, 5, 12 Interior Only (Order Branch Breakers Separately) 20-inch-wide Cabinet hsingle Phase 3-Wire Breaker Adapter Kit (Less Breaker) f No. a No NQ18L k NQ18L1C 864. backfed NQ30L k NQ30L1C NQ18L NQ18L1C 864. NQMB2HJ NQ30L NQ30L1C NQ30L NQ30L2C NQ42L NQMB2HJ NQ42L2C NQMB2Q NQ72L d NQ72L2C NQMB2KI 84d NQ84L NQ84L2C NQ30L NQ30L4C NQ42L NQ42L4C 186. Breaker Frame Size g Select QOB 2-pole or QOB-VHi Type 1 Enclosure Box 20 in. W x 5.75 in. D b Mono-Flat Front Hinged Front No. No. c No. Type 3R, 5, 12 Enclosure e Enclosure 20 in. W x 6.5in. D Height (In.) No. MH26 NC26 ( ) 47. NC26( )HR 620. MH26WP MH32 NC32 ( ) 527. NC32( )HR 657. MH32WP MH38 NC38 ( ) 54. NC38( )HR 687. MH38WP HD, HG, HJ, HLl 100A maximum NQMB2HJ 780. MH44 NC44 ( ) 663. NC44( )HR 830. MH44WP MH44 NC44 ( ) 663. NC44( )HR 830. MH44WP HD, HG, HJ, HLl 780. or JD, JG, JJ, JL MH50 NC50 ( ) 72. NC50( )HR 12. MH50WP QB,QD,QG,QJ 780. KI MH56 NC56 ( ) 786. NC56( )HR 83. MH56WP MH62 NC62 ( ) 887. NC62( )HR 110. MH62WP NQMB4LA 780. LA/LHm MH62 NC62V ( ) 887. NC62V( )HR 110. MH62WP NQMB4LA 780. LA/LHm MH62 NC62V ( ) 887. NC62V( )HR 110. MH62WP d NQ84L4C 372. NQMB4LA 780. LA/LHm MH80 NC80V ( ) NC80V( )HR MH80WP inch-wide Cabinet hthree Phase 4-Wire 15k 27k d 84d d NQ418L NQ418L1C 864. backfed NQ430L NQ430L1C NQ418L NQ418L1C NQ430L NQMB2HJ NQ430L1C NQ430L NQ430L2C NQ442L NQ442L2C NQMB2HJ NQ454L NQ454L2C 14. NQMB2Q NQ472L NQMB2KI NQ472L2C NQ484L NQ484L2C NQ430L NQ430L4C NQ442L NQ442L4C NQ472L NQ472L4C Select QOB 3-pole or QOB-VHj HD, HG, HJ, HL 100A maximum MH26 NC26 ( ) 47. NC26( )HR 620. MH26WP MH32 NC32 ( ) 527. NC32( )HR 657. MH32WP MH38 NC38 ( ) 54. NC38( )HR 687. MH38WP MH44 NC44 ( ) 663. NC44( )HR 830. MH44WP HD, HG, HJ, HL or 780. JD, JG, JJ, JL MH50 NC50 ( ) 72. NC50( )HR 12. MH50WP QB,QD,QG,QJ MH44 NC44 ( ) 663. NC44( )HR 830. MH44WP KI 780. MH56 NC56 ( ) 786. NC56( )HR 83. MH56WP MH62 NC62 ( ) 887. NC62( )HR 110. MH62WP NQMB4LA 780. LA/LHm MH62 NC62V ( ) 887. NC62V( )HR 110. MH62WP NQMB4LA 780. LA/LHm MH74 NC74V ( ) 72. NC74V( )HR MH74WP d NQ484L4C NQMB4LA 780. LA/LHm MH80 NC80V ( ) NC80V( )HR MH80WP a C suffix indicates copper bussing. b Embossed mounting holes add a 0.25 inch standoff to back of MH box. c Add F for flush mount, S for surface mount. d Use only if the Local Jurisdiction where this panelboard interior is being applied has adopted the 2008 NEC, which allows single panelboard interiors greater than 42 circuits. e Enclosure includes trim kit. f Select the appropriate main circuit breaker from the tables starting on Digest page 7-22 and add the circuit breaker price to the total price of the panelboard. g breaker interrupt ratings, See the tables starting on Digest page h For the NQ14-inch-wide panelboard offer, See Digest page -8. i QOB2150VH takes four pole spaces; all other QOB two pole circuit breakers take two pole spaces. j QOB3110VH to QOB3150VH take six pole spaces; all other QOB three pole circuit breakers take three pole spaces. k Pole spaces shown are available for branch circuits, with spaces deducted for the back fed main breaker. l For single phase applications, order a 3-pole breaker. Example: HDL m For 400A applications, order short handle circuit breaker (LAL36400MB) Schneider Electric PE1A Discount -7

8 NQ Merchandised Panelboards NQ 14-inch-wide Panelboards Class NQ 14-inch-wide240 Vac, 48 Vdc 14-inch-wide NQ panelboards are now available for those customers whose equipment space is limited. Developed with customer input, Square D brand NQ panelboards are built to last, featuring innovations for ease of installation and durability. Features 240 Vac, 48 Vdc maximum 225 A maximum main circuit breaker or main lugs 60 A maximum branch circuit breakers Visi-Trip indication on branch circuit breakers 10,000 65,000 A Short Current (SCCR) Interiors supplied with tin plated copper bus as standard Interiors accept bolt-on and plug-on branch circuit breakers Three-phase, four-wire, and single-phase, three-wire interiors available Panelboards available with Mono-Flat front Suitable for use as service entrance equipment Branch circuit filler plates provide fast and easy installation Both fully and series-rated systems are available 14-inch-wide NQ Panelboard Lug Breaker Panelboard Lug Panelboard Table.11: Max. of Breakers Lug InteriorsAccepts Plug-On and Bolt-On Branch Breakers s Total Interior, Front, Box and Adapter Kit Type 1 Type 3R, 5, 12 Interior Only (Order Branch Breakers Seperately) Type 1 Enclosure Box 14"W x 5.75" Db Mono Flat Front Hinged Front Cat. No. Cat. No. Cat. No. b Cat. No. 14-inch-wide CabinetSingle Phase 3-Wire NQ18L1C NQB NQC N/A 100 A NQ30L1C NQB NQC N/A NQ30L2C NQB NQC N/A 225 A NQ42L2C NQB NQC N/A 14-inch-wide CabinetThree Phase 4-Wire NQ418L1C NQB NQC N/A 100 A NQ430L1C NQB NQC N/A NQ430L2C NQB NQC N/A 225 A NQ442L2C NQB NQC N/A Table.12: Max. of Breakers Breaker InteriorsAccepts Plug-On and Bolt-On Branch Breakers s Total Interior, Front, Box and Adapter Kit Type 1 Type 3R, 5, 12 Interior Only (Order Branch Breakers Seperately) Cat. No. $ Price Breaker Adapter Kit (Less Breaker) Cat. No $ Price Cat. No Box 14"W x 5.75" Db Cat. No.c $ Price Type 1 Enclosure Mono Flat Front Cat. No. b Hinged Front $ Price Cat. No. $ Price 14-inch-wide CabinetSingle Phase 3-Wire 16 a NQ18L1C Select QOB NQB NQC N/A 28 a NQ30L1C pole or QOB-VH NQB NQC N/A NQ30L2C HD, HG, HJ, NQB NQC N/A NQ42L2C NQMB2HJ14 or NQMB2Q HL, OR JD, JG, JJ, JL, QB, QD, QG, QJ NQB NQC N/A 14-inch-wide CabinetThree Phase 4-Wire 15 a NQ418L1C Select QOB NQB NQC N/A 27 a NQ430L1C pole or QOB-VH NQB NQC N/A NQ430L2C HD, HG, HJ, NQB NQC N/A NQ442L2C NQMB2HJ14 or NQMB2Q HL, OR JD, JG, JJ, JL, QB, QD, QG, QJ NQB NQC N/A a Pole spaces shown are available for branch circuits, with spaces deducted for the back-fed main breaker. b Add F for flush mount, S for surface mount. c All 14 W boxes come with blank endwalls. Table.13: NQ Accessories Description No. Equipment Ground Bars Aluminum PK27GTA PK23GTA+ #1 to #4/0 lug PK23GTAL DE3A Copper PK27GTACU PE-1A Ground Bar Insulator Kit PKGTAB DE3A Filler plate (15 per package) NQFP15d PE1A Handle AttachmentsBranch Breakers Handle lock-off HLO1.0 Handle tie - (QO and QOB only) QO1HT 3.80 Handle padlock attachment1-pole QO1PA DE2A 2- and 3-pole QO1PL Handle tie and lock-off for three 1-pole (QO, QOB) QO3HT d Filler Plates are $3.00 each and must be ordered in packages of Schneider Electric PE1A Discount

9 NQ Merchandised Panelboards NQ Merchandised Accessories Class 1640 / Refer to 1640CT0801 Table.14: NQ Merchandised Neutrals s 200% Neutral Kit Copper 100% Neutral Kit Ampacity No. Box Add No. Box Add 100 NQNL NQN1CU no adder PE-1A 225 NQNL2 or NQNL2ACCYb 426. NQN2CU 12. no adder PE-1A 400 NQNL4a 63. no adder PE-1A NQN6CU 600 Not Available NQN6CUa 585. no adder PE-1A a Not to be used with SFL, FTL, or SFB. These combinations are factory assembled only. b For 225A panel with SFL, FTL, or SFB, use NQNL2ACCY (enclosure size increases by 6 inches). Otherwise, use NQNL2. Table.15: NQ Merchandised Sub-feed Lugs, Feed-through Lugs and Sub-feed Breakers Sub-feed Breaker Kits (breaker not incl.) s Ampacity Sub-feed Lugs (N/A in MCB Interiors) Feed-through Lugs Single SFB Two SFB No. No. No. No. 100 A NQSFL PE-1A 100 A not available; 225 A NQSFL PE-1A NQFTL2Lc 476. PE-1A NQSFB2Q or NQFTL2Hd NQSFB2HJ 102. PE-1A 400 A NQSFL PE-1A NQFTL4Lc 507. PE-1A Use the 2 SFB kit NQSFB4Q or NQFTL4Hd NQSFB4HJ 120. PE-1A 600 A Use FTL Factory Assembled Only Note: See Table.16 and Table.17 for box selection table. c The final character L indicates the kit is used for Low circuit count interiors 30 and 42. d The final character H indicates the kit is used for High circuit count interiors 54, 72, and 84. Table.16: Box Selection Table: Merchandised NQ Lug Panelboards with Accessories Sub-feed Lugs Feed-through Lugs Sub-feed Breakers Feature s 100 A 225 A 400 A 600 A 100 A 225 A 400 A 600 A 100 A 225 (one) A 400 (two) A 600 A (two) 2012 Schneider Electric Factory Asssembled Only Factory Asssembled Only Table.17: Feature s Box Selection Table: Merchandised NQ Vertically Mounted Breaker Panelboards w/ Accessories Feed-through Lugs Sub-feed Breakers 100 A 225 A 400 A 600 A 100 A 225 A 400 A 600 A (one) (two) (two) 18 MH26 Use FTL MH32 MH38 MH50 Use FTL MH38 MH50 MH50 MH74 30 MH62 MH62 MH86 42 MH44 MH50 Use FTL Use MH50 MH38 MH56 MH56 MH74 42 MH68 MH68 MH86 225A 72 MH50 MH62 Use FTL Interior MH50 MH68 MH62 MH86 72 MH62 MH80 MH74 f 84 MH56 MH68 Use FTL MH56 MH68 MH68 e 84 MH68 MH80 MH80 f e (c) Requires box longer than available box offer. f (c) Requires box longer than available box offer. NOTE: NQ SurgeLogic SurgeLoc Plug-on SPD appears on page -44. Table.18: NQ Optional Lugs Ampacity AL Compression Lug Kit CU Mechanical Lug Kit CU Compression Kit No. Lug Wire Range No. Lug Wire Range No. Lug Wire Range 100 NQALV1 one #8 1/0 AWG NQCUM1 one #6 2/0 AWG NQCUV1 one #6 1/0 AWG NQALV2 one #4 300 kcmil NQCUM2 one #6 250 kcmil NCQUV2 one 2/0 300 kcmil NQALV4 two 2/0 500 kcmil NQCUM4 one 1/0 750 kcmil two 1/0 350 kcmil NQCUV4 one kcmil NQALV6 two 2/0 500 kcmil NQCUM6 one 1/0 750 kcmil two 1/0 350 kcmil NQCUV6 two kcmil Table.1: NQ Accessories Description No. Sub-feed (Bolt-on) 2-pole QOB2125SL pole QOB3125SL DE2A Equipment Ground Bars Aluminum PK27GTA PK23GTA+ #1 to #4/0 lug PK23GTAL DE3A Copper PK27GTACU PE-1A Ground Bar Insulator Kit PKGTAB DE3A Filler plate (15 per package) NQFP15g PE1A I.D. Strips odd/even (left side numbered 1,3, ) NQ102OE odd/even (left side numbered 103,105, ) NQ204OE sequential (left side numbered 1,2, ) NQ102S sequential (left side numbered 103,104, ) NQ204S in. Extension NQ6RDE PE1A Rail and Deadfront Extensions 12 in. Extension NQ12RDE in. Extension NQ18RDE in. Extension NQ24RDE Touch-up paint USAS #4 Gray (Aerosol can) PK4SP 3.00 DE1 Handle AttachmentsBranch Breakers Handle lock-off HLO1.0 Handle tie - (QO and QOB only) QO1HT 3.80 Handle padlock attachment1-pole QO1PA DE2A 2- and 3-pole QO1PL Handle tie and lock-off for three 1-pole (QO, QOB) QO3HT Handle tie for two A single pole QO(B) circuit breaker QOHT Handle tie for three A single pole QO(B) circuit breaker QOHT DE2 Handle Padlock Attachment for Padlocking in OFF position For padlocking 1P QO circuit breaker in OFF position only, fixed attachment QO1PAF For padlocking 2P and 3P QO circuit breaker in OFF position only, fixed attachment QO2PAF For padlocking 1P QO-GFI, QO-AFI, QO-CAFI, and QO-EPD circuit breakers in OFF position only, fixed attachment QOGFI1PAF DE2E For padlocking 2P QO-GFI and QO-EPD circuit breakers in OFF position only, fixed attachment QOGFI2PAF Neutral or Ground Lugs #10 to #2 Al or #14 to #4 Cu QO70AN.0 #4 to #1/0 Q1100AN DE3A #1 to #4/0 Q1150AN Endwalls for MH Enclosures Blank (one per package) With Knockouts (one per package) PE1A g Filler Plates are $4.50 each and must be ordered in packages of 15. PE1A DE2A DE2E DE3A Discount Factory Asssembled Only Factory Asssembled Only -

10 QOB Bolt-On Breakers l Table.20: QOB-GFI, QOB-EPD, and QOB-EPE Breakers One-pole Two-pole Common Trip Three-poleCommon Trip Ampere a No. $ Price No. $ Price No. $ Price No. $ Price QOB-GFIQOB Qwik-Gard Breaker With Ground Fault Interrupter UL Class A 4 6 ma People Protection. b 120 Vac10 k AIR 120/240 Vac 10 k AIR 208Y/120 Vac 10 k AIR 15 A QOB115GFI 248. QOB215GFI 444. QOB315GFI A QOB120GFI 248. QOB220GFI 444. QOB320GFI A QOB125GFI 248. QOB225GFI A QOB130GFI 248. QOB230GFI 444. QOB330GFI A QOB240GFI 444. QOB340GFI A QOB250GFI 444. QOB350GFI A QOB260GFIc 444. QOB-VHGFI d 120 Vac22 k AIR 15 A QOB115VHGFI A QOB120VHGFI A QOB125VHGFI A QOB130VHGFI 47. QOB-EPDQOB Equipment protection circuit breakers with UL Listed 30 ma (EPD) or 100 ma (EPE) equipment protection. 120 Vac10 k AIR 120/240 Vac 10 k AIR 240 Vac10 k AIR 15 A QOB115EPD 417. QOB215EPD 671. QOB315EPDm1077. QOB315EPEm A QOB120EPD 417. QOB220EPD 671. QOB320EPDm1077. QOB320EPE A QOB125EPD 417. QOB225EPD A QOB130EPD 417. QOB230EPD 671. QOB330EPDm1077. QOB330EPEm A QOB240EPD 671. QOB340EPDm1077. QOB340EPEm A QOB250EPD 671. QOB350EPDm1077. QOB350EPEm A QOB260EPD 671. QOB-VHEPD 120 Vac22 k AIR 15 AQOB115VHEPD AQOB120VHEPD AQOB125VHEPD AQOB130VHEPD 772. QOB-HMHigh magnetic trip circuit breakers 15 A QOB115HMe A QOB120HMe QOB-KKey operated QOB circuit breakers f 120 Vac10 k AIR 10 A QOB110K A QOB115K A QOB120K A QOB125K A QOB130K 168. (Footnotes for Tables.20,.21, and.22) a b c d e f g A circuit breakers are suitable for use with 60 C or 75 C conductors A circuit breakers are suitable for use with 75 C conductors. Do not connect to more than 250 feet of load conductor for the total one-way run to prevent nuisance tripping. Suitable only for feeding 240 Vac and 208 Vac two-wire loads. Does not contain load neutral connection. Recommended for applications where high initial inrush may occur and for individual dimmer applications. UL Listed as SWD (switching duty) rated suitable for switching 120 Vac fluorescent lighting loads. Available in single pole construction and can be mounted in any single pole space which will accept a standard QOB. These circuit breakers can be turned ON or OFF or RESET with a special key ( No. QOK10) included with the circuit breaker. These circuit breakers are UL Listed and available as shown in the table. UL Listed for use on circuit feeding fluorescent and High Intensity Discharge (HID) lighting systems such as mercury vapor, metal halide, or high pressure sodium. These circuit breakers are physically interchangeable with QOB circuit breakers. h UL Listed 5,000 AIR on 3Ø corner grounded delta systems. i UL Listed as HACR type for use with air conditioning, heating, and refrigeration equipment having motor group combinations and marked for use with HACR type circuit breakers. j DC is not available on indicated products. k QOB2150VH uses 4 pole spaces. QOB3110VH, QOB3125VH, and QOB3150VH each use 6 pole spaces. 40A maximum circuit breaker mounted opposite. Use with 75 C wire only. l For QO plug-on circuit breaker pricing, see the tables starting on Digest page 1 2. m See note in Instruction Bulletin when using in an enclosure with a QO403 or QON prefix. Table.23: QO/QOB Breaker Wire Sizes Wire Size (AWG) Breaker Type Ampere n Al Cu QOB 1-pole QOB 2-pole QOB 3-pole A #14 8 # A two # A #8 2 # A #14 8 # A two # A #8 2 # A #4 2/0 #4 2/ A #4 300 kcmil #4 300 kcmil A #14 8 # A #8 2 # A #4 2/0 #4 2/0 QOB-VH A #4 300 kcmil #4 300 kcmil QOB-GFI and A #12 8 #14 8 QOB-EPD 40, 50, or 60 A #12 4 #14 6 n A circuit breakers are suitable for use with 60 C or 75 C conductors A circuit breakers are suitable for use with 75 C conductors. With Visi-Trip Indicator for NQ Panelboards Class 60, 730, 10, 50 Table.21: Ampere a Standard Interrupting QOB 10,000 AIR Breakers Schneider Electric DE2A Discount One-pole Two-poleCommon Trip Two-pole Common Trip h Three-pole Common Trip No. No. No. No. QOB Bolt-On 120 Vac10 k AIR 48 Vdc5 k AIR 120/240 Vac10 k AIR 48 Vdc5 k AIR j 240 Vac 10 k AIR 240 Vac10 k AIR 48 Vdc5 k AIR j 10 A QOB QOB QOB A QOB115ie 3.80 QOB215 i 8. QOB215H 240. QOB315i A QOB120 ie 3.80 QOB220 i 8. QOB220H 240. QOB320i A QOB125 i 3.80 QOB225 i 8. QOB225H 240. QOB325i A QOB130 i 3.80 QOB230 i 8. QOB230H 240. QOB330i A QOB135 i 3.80 QOB235 i 8. QOB335i A QOB140 i 3.80 QOB240 i 8. QOB240H 240. QOB340i A QOB145 i 3.80 QOB245 i 8. QOB345i A QOB150 i 3.80 QOB250i 8. QOB250H 240. QOB350i A QOB160 i 3.80 QOB260 i 8. QOB260H 240. QOB360i A QOB170 i 78. QOB270 i 168. QOB270H 308. QOB370ij A QOB280ij 240. QOB280H 366. QOB380ij A QOB20ij 240. QOB20H 366. QOB30ij A QOB2100ij 240. QOB2100H 366. QOB3100ij A QOB2110ij A QOB2125ij 501. Molded Case Switch 60 A max 240 Vac Molded Case Switch 100 A max 240 Vac Table.22: Ampere a QOB-VH QOB QOB QOB QOB High Interrupting QOB and Specialty Breakers One-pole Two-poleCommon Trip Three-poleCommon Trip No. No. No. 120 Vac22 k AIR 120/240 Vac 22 k AIR 240 Vac22 k AIR 15 A QOB115VHie 72. QOB215VHi 171. QOB315VHi A QOB120VHie 72. QOB220VHi 171. QOB320VHi A QOB125VHi 72. QOB225VHi 171. QOB325VHi A QOB130VHi 72. QOB230VHi 171. QOB330VHi A QOB140VH 86. QOB240VHi 171. QOB340VHi A QOB150VH 86. QOB250VHi 171. QOB350VHi A QOB160VH 86. QOB260VHi 171. QOB360VHi A QOB170VH 137. QOB270VHi 273. QOB370VHi A QOB280VHi 384. QOB380VHi A QOB20VHi 384. QOB30VHi A QOB2100VHi 384. QOB3100VHi A QOB2110VHi QOB3110VHk A QOB2125VHi QOB3125VHk A QOB2150VHk QOB3150VHk 180. QHB 120 Vac65 k AIR 120 Vac/240 Vac65 k AIR 240 Vac65 k AIR 15 A QHB115ie 122. QHB215i 342. QHB315i A QHB120ie 122. QHB220i 342. QHB320i A QHB125i 122. QHB225i 342. QHB325i A QHB130i 122. QHB230i 342. QHB330i 56. QOB-HIDHID circuit breakers g 120 Vac10 k AIR 120/240 Vac10 k AIR 240 Vac10 k AIR 15 A QOB115HIDe 4.50 QOB215HID 108. QOB315HID A QOB120HIDe 4.50 QOB220HID 108. QOB320HID A QOB125HID 4.50 QOB225HID 108. QOB325HID A QOB130HID 4.50 QOB230HID 108. QOB330HID A QOB140HID 4.50 QOB240HID A QOB150HID 4.50 QOB250HID 108. QOB-SWNSwitch NeutralCommon TripNEC pole2-Wire 2 Spaces 120 Vac 2-pole3-Wire 3 Spaces120/240 Vac 10 A QOB210SWN 116. QOB310SWN A QOB215SWN 116. QOB315SWN A QOB220SWN 116. QOB320SWN A QOB225SWN 116. QOB325SWN A QOB230SWN 116. QOB330SWN A QOB240SWN 116. QOB340SWN A QOB250SWN 116. QOB350SWN 170. Table.24: Breaker Type QO Arc-Fault Breakers op Ampere q 1P 120 Vac 10 kair 1 Space Required 1P 120 Vac 22 kair 1 Space Required Combination 15 A QOB115CAFI 306. QOB115VHCAFI 612. Arc-Fault Interupter 20 A QOB120CAFI 306. QOB120VHCAFI 612. Note: See Digest page 7-12 for accessories. o UL Listed as HACR type for use with air conditioning, heating, and refrigeration equipment having motor group combinations and marked for use with HACR type circuit breakers. p QO arc-fault circuit breakers provide branch feeder protection (for example, QO115AFI) or combination protection (for example, QO115CAFI) as required by the NEC and local code adoption, and comply with UL 16. q A circuit breakers are suitable for use with 60 C or 75 C conductors A circuit breakers are suitable for use with 75 C conductors.

11 NQ Factory Assembled Panelboards 240 Vac, 48 Vdc Class 1640 / Refer to 1640CT0801 Table.25: Base Price (With Solid Neutral) Breaker ( Breaker Interrupt pages 6-2 through 6-8) a Lugs s Standard IC HIC Extra HIC I-Limiter 2-pole 3-pole Breaker 2-pole 3-pole Breaker 2-pole 3-pole Breaker 2-pole 3-pole Breaker 2-pole 3-pole 60 A QOB QOB-VH HJa FI FI QOB QOB-VH A HJa FI HD HG FI Ac HD HG HJa Ac QB JD QD QG JG QJ JJa KI Ac JD JG JJa KI Ac LA LH LJ LR Abc LJ LR Note: Equipment Ground Bar38. a QL, HJ, HL, JJ, and JL circuit breakers are also available. b Copper bus standard c Prices are for 54-circuit and fewer interiors. See the Product Selector for 72- and 84-circuit interior pricing. Table.26: Breaker Ampere Branch Breakers 1-pole 120 Vac 2-pole 120/240 Vac Plug-On or Bolt-On 2-pole 240 Vac 3-pole 240 Vac 3-pole 208Y/120 Vac Space Only All Space Only except below QOB VH, Space Only ( A) ,000 AIRBranch BreakersQO, QOB, QO-H, QOB-H A d A d A d A ,000 AIRCombination Arc Fault InterruptersQO-CAFI, QOB-CAFI A ,000 AIRQwik Gard Class AQO-GFI, QOB-GFI Provided with a 5 ma setting on ground fault sensor A A A ,000 AIRQwik GardClass AQO-EPD, QOB-EPD Provided with a 30 ma setting on ground fault sensor A A A ,000 AIRQwik GardClass AQO-EPE, QOB-EPE Provided with a 100 ma setting on ground fault sensor A A (High Interrupting Capacity) 22,000 AIR Branch BreakersQO-VH, QOB-VH A A A A A e 150 A e 22,000 AIRCombination Arc Fault InterruptersQO-VHCAFI, QOB-VHCAFI A ,000 AIRQwik-GardClass AQO-VHGFI, QOB-VHGFI A ,000 AIR Branch BreakersQOH A 368. f 70 A 56. f A 688. f A f 65,000 AIR Branch BreakersQH, QHB A Table.27: Breaker Ampere Specialty Branch Breakers 1-pole 120 Vac Plug-On or Bolt-On 2-pole 120/240 Vac 2-pole 240 Vac 3-pole 240 Vac Specialty Branch Breakers (10,000 AIR) For High Intensity Discharge LightingQO-HID, QOB-HID A A Switch NeutralQO-SWN, QOB-SWN A 1-pole 2-wire (2 spaces) 2-pole 3-wire (3 spaces) High Magnetic Trip (For applications subject to high initial inrush) QO-HM, QOB-HM A 68. Sub-feed Breakers lugs or main circuit breaker interior1ø or 3Ø. Maximum 1 circuit breaker per 225 A main lug or 250 A main circuit breaker panelboard, 2 circuit breakers per A panelboard. Table.28: Sub-feed Breaker ( A) (SeeTable.2 for correct box size.) No. of Poles Ampacity QB QD QG HD HG JD JG A A Space A g Table.2: QJ, HJ, HL, JJ, and JL circuit breakers are also available. Max. No. of Branch Spaces (Does not include sub-feed circuit breaker spaces) Sub-feed Breaker Cabinet Data Box Height (20 in. W x 5.75 in. D) 225 A 250 A 400 A 600 A Lug Breaker Lug Breaker Lug h Not Available in Type 3R, 5, 12 if subfeed breaker is over 150 A. Breaker Not available with MCB Note: d e f Shunt Trip, Auxiliary Switch, and Alarm Switchaccessories for circuit breakersadd from page UL Listed for use on 3Ø, grounded BØ systems, (5,000 AIR for this application). Bolt-on only; 2-pole requires 4 vertical spaces, 3-pole requires 6 vertical spaces. Plug-on only Schneider Electric PE1 Discount -11

12 NQ Factory Assembled Panelboards Sub-feed Lugs NOTE: Available on main lug interiors only, 1Ø or 3Ø. Table.30: Feed-through Lugs ó s Sub-feed Wire Range Per Phase Incoming Outgoing Common Features Class 1640 / Refer to 1640CT0801 Price per Panel 100 one #6-2/0 one #6-2/0 $ one 1/0-350 kcmil one 1/0-350 kcmil $ one 1/0-750 kcmil Cu only one 1/0-750 kcmil Cu only $164. Table.31: Max. No. of Branch Spaces Table.32: s Sub-feed Lug Cabinet Data Box Height (20 in. W x 5.75 in. D) 100 A 225 A 400 A 18 MH26 30 MH32 MH38 MH50 42 MH44 MH50 54 MH44 MH50 72 MH50 MH62 84 MH56 MH68 Feed-through Lugs Feed-Through Wire Range Per Phase 100 A one #6-2/ A one #6 350 kcmil A one 1/0 750 kcmil or two 1/0 350 kcmil A two 1/0 750 kcmil 826. Table.33: Max. No. of Branch Spaces Lugs Feed-through Lug Cabinet Data Box Height (20 in. W x 5.75 in. D) 225 A 250 A 400 A 600 A Lugs Breaker Breaker Lugs Breaker a Table.3: Panelboard Ampacity NQ Neutral ConductorsRequired Size and Quantity Neutral Conductors Required Actual Lug Wire Range 100/125 (2) 1/0 Cu or Al (2) #4-300kcmil 225 (2) 4/0 Cu or (2) 300 kcmil Al (2) #4-300 kcmil (4) 3/0 Cu or 400 A (4) 250 kcmil Al (2) 600 kcmil Cu (2) 1/0-300 kcmil or (1) 750 kcmil (2) 750 kcmil Al Note: Neutral conductors must be of size and quantity per table above. Table.40: Metal Directory Frames Metal Directory Frame Adder Replaces standard plastic stick-on directory pouch 140. Table.41: Hinged Door-in-Door Trims Hinged Door-in-Door Trim Add Per Panel Hinged Door-in-Door Trim has piano hinge down one side. Inner door has a lock, outer door is retained with screws 646. Hinged Door-in-Door with Outer Door Lock in place of screws 836. Table.42: Weatherproof or Dusttight CabinetsType 3R, 5, 12 Weatherproof or Dusttight Cabinets Adder Note: 600 A L-Frame main circuit breaker NQ panelboards are not available with a weatherproof enclosure (Use I-Line) 400 and 600 A NQ panelboards with sub-feed circuit breakers are not available with a weatherproof enclosure (Use I-Line) A NQ panelboards are available with a subfeed breaker up to 150 A. See Table.2 on page -11. Table.43: Optional Factory Assembled Lugs for Lug Interiors Price Per Pole Adder Lug Interiors: 100A 225A 400A 600A Aluminum Compression Lugs Copper Mechanical Lugs Copper Compression Lugs a 8.75 in. deep box, ship fully assembled only. Table.34: Ground Bars Ground Bars Adder Equipment Ground Bar 38. Copper Ground Bar (add to Equipment Ground Bar price) 52. Insulated/Isolated Ground Bar (add to Equipment Ground Bar price) 86. Table.35: Name Plates Name Plates Standard white face/black letter laminated bakelite, 1 in. x 3.5 in., adhesive backed or screw mountable with screws in a bag assembly (price includes engraving) Adder Table.36: Copper Bus Bars Copper Bus Bars Adder 100 A, 225 A, 250 A A A Standard Table.37: Copper Neutrals Copper Neutrals Adder A 132. Table.38: 200% Rated Neutrals Panelboards with 200% rated neutrals are not available Add Per Panel with 250 A J- and K-frame main circuit breakers or integral lighting contactors 100 Aa one #6-2/0 kcmil per lug Aa one #6-350 kcmil per lug Aa one #1/0-750 kcmil per lug or two 1/0-300 kcmil per lug Table.44: Optional Factory Assembled Lugs for Breaker Interiors Price Per Pole Adder Breaker Interiors: H Frame J Frame LA Frame LC Frame Aluminum Compression Lugs Copper Mechanical Lugs Copper Compression Lugs Note: Optional lugs are not available for Q frame main or QOB circuit breakers Table.45: Surgelogic SurgeLoc Plug-On SPD b Surge Current Voltage ka 120 / 240 V 208 Y / 120 V 240 / 120 HLD 80 ka ka ka ka ka ka b SurgeLogic units occupy 12 circuit positions (6 adjacent mounting spaces per side.) Table.46: Surgelogic SPD Options Description Surge Counter Standard Dry Contacts Standard Remote Monitor Note: Additional factory modifications, See Digest page -38. a Two incoming neutral lugs per panel Schneider Electric PE1 Discount

13 NF Merchandised Panelboards 20-inch Wide Enclosures 480Y/277 Vac Max. Class 1670 / Refer to 1670CT0701 Table.47: Max No. of Single Pole EDB Breakers NF Lug InteriorsUse I-Line Panelboards on 480 V 3Ø3W Delta Applications NEMA 1 Enclosure $ Total Price a Interior Only b s Box 20 in. W x 5.75 in. D d Mono-Flat Front e NEMA 1 NEMA 3R, 5, 12 NEMA 3R, 5, 12 Enclosure f Hinged Front Enclosure 20 in. W x 6.5 in. D Height (In.) No. c No. No. No. No. (Single Phase 3-Wire: Factory Assembled Only) Three Phase 4-Wire NF418L MH26 NC26( ) NC26( )HR MH26WP NF418L1C MH26 NC26( ) NC26( )HR MH26WP NF430L MH32 NC32( ) NC32( )HR MH32WP NF430L1C MH32 NC32( ) NC32( )HR MH32WP NF430L MH38 NC38( ) NC38( )HR MH38WP NF430L2C MH38 NC38( ) NC38( )HR MH38WP NF442L MH44 NC44( ) NC44( )HR MH44WP NF442L2C MH44 NC44( ) NC44( )HR MH44WP NF454L MH50 NC50( ) NC50( )HR MH50WP NF454L2C MH50 NC50( ) NC50( )HR MH50WP g NF466L MH62 NC62( ) NC62( )HR MH62WP NF466L2C MH62 NC62( ) NC62( )HR MH62WP NF430L MH50 NC50V( ) NC50V( )HR MH50WP NF430L4C MH50 NC50V( ) NC50V( )HR MH50WP NF442L MH56 NC56V( ) NC56V( )HR MH56WP NF442L4C 26. MH56 NC56V( ) NC56V( )HR MH56WP g NF466L MH74 NC74V( ) NC74V( )HR MH74WP NF466L4C MH74 NC74V( ) NC74V( )HR MH74WP g NF484L MH86 NC86V( ) NC86V( )HR MH86WP NF484L4C 51. MH86 NC86V( ) NC86V( )HR MH86WP NF430L6C 26. MH50 NC50V( ) 72. NC50V( )HR 12. Factory NF442L6C MH56 NC56V( ) 786. NC56V( )HR 83. Assembled 56 66g NF466L6C 500. MH74 NC74V( ) 72. NC74V( )HR Only 74 84g NF484L6C MH86 NC86V( ) NC86V( )HR Factory Assembled Only Table.48: Max. No. of One-pole EDB Breakers NF Breaker InteriorsUse I-Line Panelboards on 480 V 3Ø3W Delta Applications NEMA 1 Enclosure $ Total Price a Breaker Adapter Kit Interior Only b s NEMA 1 NEMA 3R,5,12 NEMA 3R, 5, 12 Enclosure f Box Mono-Flat Breaker 20 in. W x 5.75in. D d Front e Hinged Front Enclosure 20 in. W x 6.5 in. D Height Frame (In.) Kit No. c No. No. No. No. (Single Phase 3-Wire: Factory Assembled Only) Three Phase 4-Wire NF418L MH26 NC26( ) NC26( )HR MH26WP Back-fed EDB, EGB NF418L1C MH26 NC26( ) NC26( )HR MH26WP Breakerh or EJB NF430L MH32 NC32( ) NC32( )HR MH32WP NF430L1C MH32 NC32( ) NC32( )HR MH32WP NF418L MH38 NC38( ) NC38( )HR MH38WP N150MH or N100MFIi 780. HD/HG/ NF418L1C MH38 NC38( ) NC38( )HR MH38WP HJ/HL or FI NF430L MH44 NC44( ) NC44( )HR MH44WP NF430L1C MH44 NC44( ) NC44( )HR MH44WP NF430L MH50 NC50( ) NC50( )HR MH50WP NF430L2C MH50 NC50( ) NC50( )HR MH50WP NF442L MH56 NC56( ) NC56( )HR MH56WP N250MJ 780. JD/JG/ NF442L2C MH56 NC56( ) NC56( )HR MH56WP or JJ/JL N250MKCi 780. or KI NF454L MH62 NC62( ) NC62( )HR MH62WP NF454L2C MH62 NC62( ) NC62( )HR MH62WP 66g NF466L MH74 NC74( ) NC74( )HR MH74WP NF466L2C MH74 NC74( ) NC74( )HR MH74WP NF430L MH62 NC62V( ) N400Mi NC62V( )HR MH62WP NF430L4C MH62 NC62V( ) NC62V( )HR MH62WP NF442L MH68 NC68V( ) N400Mi 780. LA/LH 48. NC68V( )HR MH68WP NF442L4C 26. MH68 NC68V( ) NC68V( )HR MH68WP 66g NF466L MH86 NC86V( ) N400Mi NC86V( )HR MH86WP NF466L4C MH86 NC86V( ) NC86V( )HR MH86WP a Total Price includes: interior, front, main circuit breaker adapter kit, and enclosure. b Order branch circuit breakers separately. c C suffix indicates copper bussing. d Embossed mounting holes add a 0.25-inch standoff to back of MH box. e Add F for flush mount, S for surface mount. f Enclosure includes trim kit. g Use only if the Local Jurisdiction where this panelboard interior is being applied has adopted the 2008 NEC, which allows single panelboard interiors greater than 42 circuits. h Back-fed EDB 125 A 3 pole main circuit breaker must be ordered separately and field installed. Maximum breaker rating opposite is 20A. i Select the appropriate main circuit breaker from pages starting on 7-21 and add the circuit breaker Price to the total Price of the panelboard Table.4: NF Merchandised SPD Box Selection Table Lug Panelboard Box Requirements Breaker Panelboard Box Requirements s Max. Breaker NEMA 1 Spaces Enclosure NEMA 3R, 5, 12 Enclosure NEMA 1 Enclosure NEMA 3R, 5, 12 Enclosure Box Front Hinged Enclosure Box Front Hinged Enclosure 250A 42 MH56 NC56( ) 887. NC56( )HR 110. MH56WP MH68 NC68( ) 72. NC68( )HR MH68WP A 42 MH68 NC68V( ) 72. NC68V( )HR MH68WP MH80 NC80( ) M/B NC80V( )HR MH80WP Schneider Electric PE1A Discount -13

14 NF Merchandised Panelboards Accessories Class 1670 / Refer to 1670CT Table.50: NF Merchandised Neutrals s 200% Neutral Kit Copper 100% Neutral Kit Ampacity No. Box Add No. Box Add 125 NFNL NFN1CU No Adder PE-1A 250 NFNL NFN2CU 405. No Adder PE-1A 400 NFNL4a 114. No Adder PE-1A NFN6CU 600 Factory Assembled Only NFN6CUa No Adder PE-1A a Table.51: s Ampacity Not to be used with SFL, FTL, or SFB. These combinations are factory assembled only. Modifications (Single- or Three-phase) Sub-feed Lugs b c Feed-through Lugs b c s Ampacity Sub-feed Breaker Kits b (circuit breaker not Included) d Single Sub-feed Twin Sub-feed No. No. Breaker Breakers No. No. 125 NF125SFL 167. PE-1A NF125FTL 336. PE-1A 250 NF250SFBH/NF250SFBJ 102. PE-1A 250 NF250SFL 213. PE-1A NF250FTL 476. PE-1A NF600SFBH NF400SFLe 356. PE-1A NF400FTL 507. PE-1A NF600SFBJ 120. PE1A 600 f f FACTORY ASSEMBLED ONLY 800 FACTORY ASSEMBLED ONLY Note: b c d e f NF250SFBH and NF600SFBH are for use with HDL, HGL, HJL, and HLL circuit breakers. NF600SFBJ are for use with JDL, JGL, JJL, and JLL circuit breakers. Available factory assembled only on non-linear panelboards. Select box from the Box Selection Table. Order appropriate circuit breaker. Use copper wire only. Available factory assembled only. Table.52: Special Features Box Selection TableStandard Mechanical Lugs Only Lugs Only Feature Sub-feed Lugs Feed-through Lugs Sub-feed Breaker No. of s Ampacity Cat. No. Cat. No. Cat. No. Cat No. Cat No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. 100/125 MH26 MH32 MH32 MH MH38 MH44 MH62 MH50 MH56 MH74 MH56 MH62 MH MH50 MH56 MH74 MH86 MH56 MH62 MH80 MH2 MH68 MH g g g g g g g g g g g g Available factory assembled only. Table.53: Special Features Box Selection TableStandard Mechanical Lugs Only (continued) Vertical Breaker h Back-fed Breaker Feature Feed-through Lugs Sub-feed Breaker Feed-through Lugs No. of s Ampacity Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. Cat. No. 100/125 MH44 MH50 MH32 MH MH62 MH68 MH86 MH68 MH74 MH38 MH44 400h MH68 MH74 MH2 MH80 MH Available factory assembled only. h 400 A dimension for LA/LH main circuit breakers only. Table.54: Optional Lug Kits for Lug Panelboards Ampacity AL Compression Lug Kit CU Mechanical Lug Kit CU Compression Lug Kit i No. Lug Wire Range No. Lug Wire Range No. Lug Wire Range 125 NFALV1j one #4 300 kcmil 177. NFCUM1 #6 2/0 AWG NFCUV1 k one #6 1/ PE-1A 347. PE-1A 250 NFALV2 one kcmil 333. NFCUM2 #6 250 kcmil NFCUV2k one 2/0 300 kcmil 417. PE-1A 400 NFALV4 two 2/0 500 kcmil PE-1A NFCUM4 one 1/0 750 kcmil, two 1/0 350 kcmil 87. PE-1A NFCUV4 one kcmil 767. PE-1A 600 NFALV6 two 2/0 500 kcmil PE-1A NFCUM6 two 1/0 750 kcmil PE-1A NFCUV6 two kcmil PE-1A 800 Contact your local Schneider Electric representative or distributor i Use copper wire only. j Use of this kit requires an additional 6 in. added to box height. k Use of this kit to terminate larger than standard wire size requires an additional 6 in. added to box height. Table.55: NF Accessories Description No. Description No. Aluminum Equipment Ground Bar PK27GTA DE-3A Filler plate (15 per package) NFFP15 00l PE-1A Copper Equipment Ground Bar PK27GTACU PE-1A EXB Fixed padlock attachment, Lock ON/OFF for ED, EG, and EJ Breakers 1, 2, or 3 poles EDPA DE-2 Large Aluminum Lug for Equipment Ground Bar PK23GTAL DE-3A Equipment Ground Bar Insulator Kit PKGTAB EXB Fixed padlock attachment, Lock OFF only for ED, EG, and EJ Breakers 1, 2, or 3 poles EDPAF DE-2 I.D. number strips odd/even (left side numbered 1, 3, ) NF102OE odd/even (left side numbered 103, 105, ) NF204OE Oversized Lugs for Neutral or Ground Bar 7.0 PE-1A sequential (left side numbered 1, 2, ) NF102S #10 to #2 Al or #14 to #4 Cu QO70AN sequential (left side numbered 103, 104, ) NF204S #4 to #1/0 Q1100AN DE-3A Rail and Deadfront Extensions #1 to #4/0 Q1150AN in. Extension NF6RDE Drip Hood for 20 in. wide enclosures MHT2DH PE-1A 12 in. Extension NF12RDE PE-1A 18 in. Extension NF18RDE l Filler plates are $7.50 each and must be ordered in packages of Schneider Electric PE1A DE3A DE1 Discount

15 Breakers For NF Merchandised Panelboards Class 515 EDB-EPD 1-pole with Alarm Switch EDB, EGB, EJB 3-pole A EDB, EGB, EJB 1-pole A EDB, EGB, EJB 2-pole A Table.56: E-frame125 A, Thermal-magnetic (480Y/277 Vac) ED, EG, EJ D Interrupting Level G Interrupting Level J Interrupting Level Ampere (480Y/277 Vac) Y/277 Vac Y/277 Vac Y/277 Vac Terminal Wire Range Hold Trip 1-pole, 277 Vac 15 A EDB14015ab EGB14015ab EJB14015ab 20 A EDB14020ab EGB14020ab EJB14020ab AL30FD #14 #6 25 A EDB14025b EGB14025b EJB14025b 30 A EDB14030b EGB14030b EJB14030b 35 A EDB14035b EGB14035b EJB14035b 40 A EDB14040b EGB14040b EJB14040b 45 A EDB14045b 150. EGB14045b 225. EJB14045b 408. AL100FD 50 A EDB14050b EGB14050b EJB14050b #14 2/0 60 A EDB14060 EGB14060 EJB A EDB EGB EJB pole, 480Y/277 Vac c 15 A EDB24015b EGB24015b EJB24015b 20 A EDB24020b EGB24020b EJB24020b AL30FD #14 #6 25 A EDB24025b EGB24025b EJB24025b 30 A EDB24030b EGB24030b EJB24030b 35 A EDB24035b EGB24035b EJB24035b 40 A EDB24040b EGB24040b EJB24040b 45 A EDB24045b 536. EGB24045b 776. EJB24045b A EDB24050b EGB24050b EJB24050b 60 A EDB24060 EGB24060 EJB A EDB EGB EJB A EDB24080 EGB24080 EJB A EDB EGB EJB A EDB24100 EGB24100 EJB A EDB24110 EGB24110 EJB A EDB24125 EGB24125 EJB pole, 480Y/277 Vac 15 A EDB34015b EGB34015b EJB34015b 20 A EDB34020b EGB34020b EJB34020b A EDB34025b EGB34025b EJB34025b A EDB34030b EGB34030b EJB34030b 35 A EDB34035b EGB34035b EJB34035b 40 A EDB34040b EGB34040b EJB34040b 45 A EDB34045b 66. EGB34045b EJB34045b A EDB34050b EGB34050b EJB34050b 60 A EDB34060 EGB34060 EJB A EDB EGB EJB AL100FD #14 2/ AL100FD #14 2/ AL30FD #14 #6 AL100FD #14 2/0 80 A EDB34080 EGB34080 EJB A EDB EGB EJB AL100FD 100 A EDB34100 EGB34100 EJB34100 #14 2/0 110 A EDB34110 EGB34110 EJB A EDB34125 EGB34125 EJB34125 EPDs (Equipment Protection Devices), 1-pole, 277 Vac, Thermal-magnetic with 30 ma ground-fault protectiond 15 A EDB14015EPDab EGB14015EPDab EJB14015EPDab 20 A EDB14020EPDab EGB14020EPDab EJB14020EPDab 140. #14 #6 Cu 30 A EDB14030EPDb EGB14030EPDb EJB14030EPDb or 40 A EDB14040EPDb EGB14040EPDb EJB14040EPDb #12 #4 Al A EDB14050EPDb EGB14050EPDb EJB14050EPDb Note: All EDB, EGB, and EJB circuit breakers are UL Listed as HACR Type. For 50 o C calibration, use a CA suffix. NF branch circuit breakers are fungus proof as standard. a UL Listed as SWD (Switching duty rated). b UL Listed as HID (High Intensity Discharge rated). c UL Listed for use on 240 V Corner-grounded Delta Systems (Grounded B Phase). See data bulletin 2700DB0202. d All EPDs occupy two spaces, with or without Alarm Switch option. For alarm switch, add 158 list Price and the suffix BA. Table.57: Factory installed Electrical Accessories Auxiliary Switch (1A/1B) Monitors circuit breaker contact status and provides a remote signal indicating the circuit breaker contacts are OPEN or CLOSED. Application Max Load = Vac 50/60 Hz Terminals for #14 AWG Cu wire Alarm Switch (NO) Used with control circuits and is actuated only when the circuit breaker has tripped. Application Max Load = Vac 50/60 Hz Terminals for #14 AWG Cu wire. Table.58: Factory Installed Electrical Accessory Packages for ED, EG, EJ Breakers Accessory Package Suffix Auxiliary Switch/Alarm Switch Packageef AABA 312. Shunt Trip Packageef SA 755. Auxiliary Switch/Alarm Switch/Shunt Trip Packageef AABASA Alarm Switch (N.O.) Package for EPDs only BA 237. e f Accessory package takes an additional pole space. Not available for EPD. Table.5: Terminal Nut Insert Kit Breaker Type Qty. per Kit No. ED, EG, EJ 3 TIKFD Minimum Recommended Supply Transformer (VA) Coil Burden Max. (VA) Shunt TripTrips the circuit breaker from a remote location by means of a coil energized from a separate circuit. A 120 V shunt trip will operate at 55% or more of rated voltage. Application For use with momentary or maintained push button. 120 Vac 50/60 Hz Terminals for #14 AWG Cu wire. Table.60: Handle Accessories Breaker Type No. of Poles No. EXB Fixed Padlock Attachment, Lock ON/OFF ED, EG, EJ 1, 2, or 3 EDPA 3.00 EXB Fixed padlock attachment, Lock OFF only ED, EG, EJ 1, 2, or 3 EDPAF EXB Removable padlock attachment, Lock OFF only ED, EG, EJ 1, 2, or 3 HPAFD EXB Handle Ties ED, EG, EJ Ties 2 1P ECB2HT Ties 3 1P ECB3HT Table.61: Interrupt s (ka) EDB EGB EJB 120 V V 18 (1P), (1P), (1P), Y/277 V Table.62: Mechanical Lug Kit Information (Al lugs for use with wire) Breaker Application of Wires Per Lug Lugs and Wire Range Standard Ampere Optional Ampere Per Kit A one #12#6 AWG Al or one #14#6 AWG Cu AL30FD 3 EDB, EGB, EJB A EDB, EGB, EJB A g one #122/0 AWG Al or one #142/0 AWG Cu AL100FD 3 EDB, EGB, EJB A one #141/0 AWG Cu CU100FD 3 $ price Per Kit g Factory installed only. Use suffix LH E-frame dimensions Digest page Schneider Electric DE2 Discount -15

16 NF Factory Assembled Panelboards a Factory Assembled Pricing Maximum 480Y/277 Vac Class 1670 / Refer to 1670CT a Use I-Line Panelboards on 480 V 3Ø3W Delta applications. Table.63: Base (including solid neutral) Breaker ( Breaker Interrupt 7-2 through 7-8) ab Lugs s Standard IC HIC Extra HIC I-Limiter 2-pole 3-pole Breaker 2-pole 3-pole Breaker 2-pole 3-pole Breaker 2-pole 3-pole Breaker 100 A EDc EGc A HJ FI A EDc EGc A HD HG HJ A d JD JG JJ KI A d JD JG JJ KI A d LA LH LC LI A de LC LI Ae pole 3-pole a b c d e HL and JL frame circuit breakers are also available as main circuit breakers. Contact your local Schneider Electric representative or distributor for Micrologic trip main circuit breaker pricing. Back-fed main circuit breaker. Prices are for 54-circuit and fewer interiors. See the Product Selector for 66- and 84-circuit interior pricing. Copper bus only. Table.64: Breaker Ampere Branch Breakers per circuit breaker Standard Interrupting 25, Vac, 18, Y/277 Vac ED Bolt-on Branch High Interrupting 65, Vac, 35, Y/277 Vac EG Bolt-on Branch Extra High Interrupting 100, Vac, 65, Y/277 Vac EJ Bolt-on Branch 1-pole 2-pole 3-pole 1-pole 2-pole 3-pole 1-pole 2-pole 3-pole A A A A Space Only Note: All ED, EG, and EJ branch circuit breakers are UL Listed as HACR type. Table.65: Breaker Ampere EDB-EPD Equipment Protection Device Branch Breakers fg Standard Interrupting 25, Vac, 18, Y/277 Vac ED Bolt-on Branch High Interrupting 65, Vac, 35, Y/277 Vac EG Bolt-on Branch Extra High Interrupting 100, Vac, 65, Y/277 Vac EJ Bolt-on Branch 1-pole 2-pole 3-pole 1-pole 2-pole 3-pole 1-pole 2-pole 3-pole A f g All 1-pole EDB-EPD branches use 2 poles of mounting space. For bell alarm in EDB-EPD branch breaker, add 158. to branch breaker price. Sub-feed Breaker Available on 1Ø or 3Ø, A main lugs or A main circuit breaker interiors One sub-feed HD, HG, HJ, or HL or JD, JG, JJ, or JL circuit breaker per 250 A panelboard Two sub-feed HD, HG, HJ, or HL or two JD, JG, JJ, or JL circuit breakers per 400 A panelboard (do not mix H and J in a Panel) One sub-feed LA, LH, or LC circuit breaker (400 A max.) and one JD, JG, JJ, or JL circuit breaker or two sub-feed JD, JG, JJ, or JL circuit breakers per 600 A or 800 A panelboard (JJ and LC sub-feed circuit breakers cannot be used together). Table.66: Sub-feed Breaker ( A) No. of Poles HD HG JD JG LA LH LC h Space h JJ and LC sub-feed circuit breakers cannot be used together. Table.67: Sub-feed Breaker Cabinet Data Max. No. of Branch Spaces (Does not include sub-feed circuit breaker spaces) Box Height (20 in. W x 5.75 in. D) 250 A 400 A LA/LH 600 A 800 A Lugs Breaker Lugs Breaker Lugs Breaker i Lugs j k k k N/A 84 N/A i j k 600 A main circuit breaker panelboards require an 8.75 in. deep, 26 in. wide box. 800 A main lug panelboards require an 8.75 in. deep, 26 in. wide box. Dimensions also for 400 A LC/LI main circuit breaker panels Schneider Electric PE1 Discount

17 NF Factory Assembled Panelboards Common Features Class 1670 / Refer to 1670CT0701 Table.68: Sub-feed (Double) Lugs (Standard Aluminum Mechanical Lugs) An additional mains end termination point that can be used to feed out to another panelboard or device from the incoming service lines. NOTE: Available on main lug interiors only. s Sub-feed Wire Range Wire Bending Space per NEC Table A two #6 2/ A two 1/0 350 kcmil A two 1/0 600 kcmil Cu A (4) 4/0 500 kcmil A (6) 3/0 500 kcmil 522. Table.6: Sub-feed Lug Cabinet Data (Standard Aluminum Mechanical Lugs) Max. No. of Lugs Box Height in Inches (20 in. W x 5.75 in. D) Branch Spaces 125 A 250 A 400 A 600 A 800 A a a 800 A main lug panelboards require an 8.75 in. deep and 26 in. wide box. Table.70: Feed-through Lugs (Standard Aluminum Mechanical Lugs) A second set of lugs assembled at the opposite end from the mains of the panelboard. Often used to connect another panelboard or device to the incoming lines. Available on main lugs and main circuit breaker panelboards. s Feed-through Wire Range Wire Bending Space per NEC Table A one #6 2/0 kcmil A one #6 350 kcmil A one 1/0 750 kcmil or two 1/0 350 kcmil A two 1/0 600 kcmil 826. Table.71: Max. No. of Branch Spaces Feed-through Lug Cabinet Data (Standard Aluminum Mechanical Lugs) Box Height in Inches (20 in. W x 5.75 in. D) 125 A 100/125 A 250 A 400 A LA/LH 600 A 800 A Breaker (back-fed only) Lugs Breaker Lugs Breaker Lugs Breaker Lugs Breaker b Lugs c Table.76: 200% Rated Neutrals Panelboards with 200% rated neutrals are available with sub-feed lugs, feed-through lugs, and main circuit breakers Note: Neutral conductors must be of size and quantity per table above. Add Per Panel 250 A A A A 184. Table.77: NF Neutral ConductorsRequired Size and Quantity Panelboard Ampacity Neutral Conductors Required c Actual Lug Wire Range 125 (2) 1/0 Cu or (2) 1/0 Al (2) #6-2/0 250 (2) 4/0 Cu or (2) 300 kcmil Al (2) #6-350 kcmil 400 A (4) 250 kcmil Al or (4) 3/0 Cuor (2) 600 kcmil Al (2) 1/0-300 kcmil or (1) 1/0-750 kcmil 600 (4) 500 kcmil Al or (4) 350 kcmil Cu (2) 1/0-750 kcmil Table.78: Metal Directory Frame Metal Directory Frame Not available with LC/LI main circuit breaker (Replaces standard plastic stick-on directory pouch) Adder Table.7: Hinged Door-in-Door Trim Hinged Door-in-Door Trim Add Per Panel Hinged Door-in-Door Trim has piano hinge down one side. Inner door has a lock, outer door is retained with screws 646. Hinged Door-in-Door with Outer Door Lock in place of screws 836. Table.80: Weatherproof or Dusttight Cabinets (Type 3R, 5, 12) Weatherproof or Dusttight Cabinets Type 3R, 5, 12 Adder (Not available with panelboards having LC/LE/LI/LX/LXI main circuit breakers) Table.81: Optional Factory Assembled Lugs for Lug Interiors Per Pole Adder Lug Interiors 100 A 225 A 400 A 600 A 800 A Aluminum Compression Lugs Copper Mechanical Lugs Copper Compression Lugs b c 600 A main circuit breaker panelboards require an 8.75 in. deep, 26 in. wide box. 800 A main lug panelboards require an 8.75 in. deep, 26 in. wide box. Table.72: Ground Bars Ground Bars Adder Equipment Ground Bar 38. Copper Ground Bar (Add to Equipment Ground Bar Price) 52. Insulated/Isolated Ground Bar (Add to Equipment Ground Bar Price) 86. Table.73: Name Plates Name Plates Standard white face/black letter laminated bakelite, 1 in. x 3.5 in., adhesive-backed or screw mountable with screws in a bag assembly (Price includes engraving) Adder Table.74: Copper Bus Bars Copper Bus Bars Adder 100 A, 250 A A A, 800 A Standard Table.75: Copper Neutral Copper Neutral Adder A A Table.82: Optional Factory Assembled Lugs for Breaker Interiors Per Pole Adder Breaker Interiors H Frame J Frame LA Frame LC Frame Aluminum Compression Lugs Copper Mechanical Lugs Copper Compression Lugs Table.83: d Surge Current ka Surgelogic Hard Bus SPDModel IMA d Voltage 208Y/120 V 3Ø4W 240/120 V 3Ø4W High Leg 480Y/277 V 3Ø4W Panelboard box height with SPD unitcontact your local Schneider Electric representative or distributor. Table.84: Surgelogic SPD Options Surgelogic SPD Options Surge Counter Standard Dry Contacts Standard Remote Monitor NOTE: For additional factory modifications, See Digest page Schneider Electric PE1 Discount -17

18 NQ/NF Merchandised Single Row (Column Width) Panelboards Class 1640 / Refer to 1670CT0701, 1640CT NQ Single-Row (Column-width)240 Vac Bolt-on (60 A Max. Branch Breaker) NQ Application Data Application: For use on ac only. Meet Federal Specification W-P-115c, Type 1, Class 1. UL Listed. Service: 1Ø3W, 3Ø3W, 3Ø4W, 3 Grd. B Ø240 Vac max. AIR: See the tables starting on Digest page 7-2. s: Type NQBolt-on main lugs: 100 A, 225 A circuit breaker: 100 AQOU, 225 AQB See the tables starting on Digest page 7-2 for main circuit breaker interrupt ratings. See catalog for terminal lug data. circuit breakers with higher interrupt ratings are available as factory assembled panelboards. Branches: Bolt-on QOB, 60 A maximum. QOB A 1-, 2- and 3-pole. See Digest page -10 for branch circuit breaker terminal data. QOB-VH and QHB branch circuit breakers are also available as factory assembled. Cabinet: FrontScrew cover. Boxgalvanized steel with removable endwalls. Gutters: 100 A4 in. min. mains end, 3 in. min. opposite mains 225 A10 in. min. mains end, 5 in. min. opposite mains NF Single-Row (Column-width)480Y/277 Vac Bolt-on (60 A Max. Branch Breaker) NF Application Data Application: For use on ac only. Meet Federal Specification W-P-115c, Type 1, Class 1. UL Listed. Service: 480Y/277 Vac, 3Ø4W AIR: See the tables starting on Digest page 7-2 s: Type NF Bolt-on main lugs: 125 A, 225 A circuit breaker: 100 AFA, 100 AHD, 225 AJD. See the tables starting on Digest page 7-2 for main circuit breaker interrupt rating. See the catalog section for terminal lug data. circuit breakers with higher interrupt ratings are available as factory assembled panelboards. Branches: EDB, EDG, or EDJ, 60 A maximum. See Digest page -15 for branch circuit breaker catalog numbers, List Prices and terminal data. Cabinet: FrontScrew cover. Boxgalvanized steel with removable endwalls. Gutters: 100 A4 in. min. mains end, 3 in. min.opposite mains 225 A10 in. min. mains end, 5 in. min. opposite mains Table.85: Max. No. of Poles s NQ Single-Row (Column-width)240 Vac Bolt-on a Total (Box Interior and Front) Box and Interior with Solid Neutral (8.625 in. W. x 5 in. D.) (Order branch circuit breakers separately) Box Height (In.) Front (Surface Mount) 1 Phase 3-Wire Lugs Only NQ830L2C LX45TS 371. Breaker2-pole NQ820B1C LX40TS Phase 4-Wire Lugs Only NQ8430L1C LX40TS NQ8442L2C LX58TS 480. Breaker3-pole NQ8430B1C LX45TS NQ8442B2C LX62TS 545. Table.87: Max. No. of Poles s NF Single-Row (Column-width)480Y/277 Vac Bolt-on Total (Box Interior and Front) Box and Interior with S/N (8.625 in. W. x in. D.) Box Height (In.) Front (Surface Mount) Lugs Only3 Phase 4-Wire NF8430L1C NC5TS NF8442L2C NC71TS 522. Breaker3-pole NF8430M1C NF8430M1HDC NC65TS NF8442M2JDC NC85TS 618. a 60 A Maximum BranchCopper Bus Standard. Table.86: Cable Troughs and Pull Boxes Cable Troughs (L=Length) b b L (In.) in. x 5 in. 36 MTX MTX MTX MTX Cable troughs are standard with a trough barrier. S/N Terminals Pull Boxes with Solid Neutral 42 MPX Table.88: Cable Troughs and Pull Boxes Cable Troughs (L=Length) c c d L (In.) in. x in. d 36 NTX NTX NTX NTX S/N Terminals Cable troughs are standard with a trough barrier. Box width = in.; width at front, including flange, is.625 in.. Pull Boxes with Solid Neutral 42 MPX in. 15 in. Cable Trough Length Pull Box (Cover Removed) Solid Neutral Bar Cable Trough Column Width Lighting Panelboard in. Panel Height Schneider Electric PE1A Discount

19 NQ/NF Factory Assembled Single Row (Column Width) Panelboards Class 1640 / Refer to 1670CT0701, 1640CT0801 NQ Single Row (Column-Width)240 Vac Bolt-On Factory Assembled Pricing Table.8: Note: s Base Price with Solid Neutral Lugs Breaker ( Breaker Interrupt see Digest pages 7-2 through Pole 3-Pole Breaker 2-Pole 3-Pole Breaker 2-Pole 3-Pole QOB A QB QD QG A QB QD QG 400. Copper bus standard. Equipment Ground Bar adder$ Copper Equipment Ground Bar (Add to Equipment Ground Bar ) adder$ Table.0: Branch Breakers (price per breaker) Breaker Ampere 1-Pole 120 Vac 2-Pole 120/240 Vac 2-Pole 240 Vac 3-Pole 240 Vac Space Only All Space Only Except Below ,000 AIRBranch BreakersQOB, QOB-H A ,000 AIRQwik-Guard Class AQOB-GFI A A 488. Specialty Branch Breakers (10,000 AIR) For High Intensity Discharge LightingQO-HID, QOB-HID A A High Magnetic Trip (For applications subject to high initial inrush)qo-hm, QOB-HN A 68. Provides 30 ma Equipment ProtectionQO-EPD, QOB-EPD A (High Interrupting Capacity) 22,000 AIR Branch BreakersQO-VH, QOB-VH A A ,000 AIRQwik-GuardClass AQO-VHGFI, QOB-VHGFI A 24. NF Single Row (Column-Width)480Y/277 Vac 3Ø4W Bolt-on Factory Assembly Pricing Table.1: Base Price with Solid Neutral Breaker ( Breaker Interrupt see Digest pages 7-3 through 7-4 Lugs s Standard IC HIC Extra HIC I-Limiter Breaker 2-Pole 3-Pole 2-Pole 3-Pole Breaker 2-Pole 3-Pole Breaker 2-Pole 3-Pole Breaker 2-Pole 3-Pole FA FH A FI 732. HD HG HJ 125 A KI A HD HG HJ KI A JD JG 582. JJ 802. Note: Copper busstandard. Copper Neutral adder$ Equipment Ground Bar adder$ Copper Equipment Ground Bar (Add to Equipment Ground Bar ) adder$ Table.2: Branch Breakers (price per breaker) Breaker Ampere Standard Interrupting 25, Vac, 18,000 Vac ED Bolt-on Branch High Interrupting 65, Vac, 35,000 Vac EG Bolt-on Branch Extra High Interrupting 100,000 65, Y/277 Vac EJ Bolt-on Branch 1-Pole 2-Pole 3-Pole 1-Pole 2-Pole 3-Pole 1-Pole 2-Pole 3-Pole A Space Only Table.3: EDB-EPD Equipment Protection Device Branch Breakers Breaker Ampere Standard Interrupting 25, Vac, 18,000 Vac ED Bolt-on Branch High Interrupting 65, Vac, 35,000 Vac EG Bolt-on Branch Extra High Interrupting 100,000 65, Y/277 Vac EJ Bolt-on Branch 1-Pole 2-Pole 3-Pole 1-Pole 2-Pole 3-Pole 1-Pole 2-Pole 3-Pole A Schneider Electric PE-1 Discount -1

20 I-Line and QMB Panelboards I-Line Merchandised Pricing Procedure Pricing Procedure and Examples Class 2110, 4620 / Refer to 2110CT701, 4620CT Select the appropriate branch circuit breakers and accessories based on the required ampacity and AIR ratings from Digest pages -24 through Determine the total mounting inches required by the branch circuit breakers. Pay close attention to the interior types and any branch mounting restrictions by referring to panel layouts on Digest pages -21 and -22. For example, larger frame circuit breakers may mount in only one side of the panel due to physical sizes. Therefore, for larger size branches, you may only be able to consider one half of the total mounting inches available. 3. Select proper main lug interior or main circuit breaker interior from Digest page -21 or -22 based on the mains ampacity and branch requirements from step Select blanks from the Accessories table on Digest page -23 as required to cover unused mounting space. 5. Select appropriate box and front from Digest page -21 or -22 to accommodate panel interior selected in step Apply appropriate discount schedule. Table.4: I-Line Merchandised Pricing Example 600 Vac, 3Ø3W, 400 A, MLO, 14k AIR, Type 1 enclosure, 4 piece surface trim without door. Description No. Digest Page No. 400 Amp MLO Interior HCM Piece Surface Trim Without Door HCM73TS Type 1 Enclosure HC3273B (8) 60/3 FA one 100/2 FA26100AC one 4.5 in. Blanks HNM4BL one 1.5 in. Blank HNM1BL Total Price I-Line Factory Assembled Pricing Procedure 1. Select price for main lugs or main circuit breaker from Base Price tables on Digest page -31. Include solid neutral and ground bar when required. 2. List branch circuit breakers and determine total mounting inches required. Include space only charge and mounting inches as required. Price branches from Digest page If total space required exceeds the maximum listed, price as two or more panels and add price for sub-feed lugs, so installer can cable between sections. 4. Add price for special features from Digest page For complete price, total all prices. Order panel by description. 6. Apply appropriate discount schedule. Table.5: I-Line Factory Assembled Pricing Example 600 Vac, 3Ø3W, 400 A, MLO, 14k AIR, Type 1 enclosure, 4 piece surface trim without door. Description Digest Page No. 400 A MLO Base Price (8) 60/ one 100/ (3) 250/ Total Price QMB Factory Assembled QMB PanelboardsMethod of Pricing 1. Make a sketch with main lugs or main switch at the top or bottom. 2. List required branch devices (switches and circuit breaker units). Include ampere rating, number of poles, and unit mounting height from the appropriate table on Digest pages -35 and twin units are the same price as 600 V twin units and twin units are the same price as 600 V twin units. 5. List solid neutral from Digest page -36 if required. No unit mounting height is required. 6. List mains ampere rating, voltage, number of poles, and unit mounting space from the appropriate table on If total unit mounting height of branch devices exceeds maximum mounting space of the mains, price as two or more panelboards, adding sub-feed lugs or feed-thru lugs from the appropriate table on Digest page Insert at the right of each item the price from the appropriate table, including any accessories. The sum will be the complete panelboard price including the cabinet.. Specify H, R, or J fuse clips. Table.6: QMB Factory Assembled Pricing Example 600 Vac, 3Ø3W, 400 A, Fusible 10k AIR, Type 1 Enclosure Branches Digest Page No. 400 A MLO Base Price (4) 60/ one 100/ one 30/3 Total Price Schneider Electric Example pricing only Discount

21 I-Line Merchandised Panelboards 600 Vac, 250 Vdc Class 2110 / Refer to 2110CT701 TYPE HCN 225 A max. (240 V max.) branch circuit breaker QB, QD, QG, QJ 150 A max. branch circuit breaker FA, FH, FY, HD, HG, HJ, HL l 1 2 Total Breaker Mounting Space Each Side QB, QD QG, QJ FA, FH FY S N HD, HG HJ, HL QB, QD QG, QJ FA, FH FY HD, HG HJ, HL 600 A Max. Lugs or 400 A Max. Breaker Box Size: 26 in. Wide, 6.5 in. Deep TYPE HCM 250 A max. branch circuit breaker FA, FH, FY, FI, QB, QD, QG, QJ, HD, HG, HJ, HL, JD, JG, JJ, JL QB, QD QG, QJ FA, FH FI, FY HD, HG HJ, HL JD, JG JJ, JL 1 2 Total Breaker Mounting Space Each Side S N QB, QD QG, QJ FA, FH FI, FY HD, HG HJ, HL JD, JG JJ, JL 800 A Max. Lugs or 800 A Max. Breaker Box Size: 32 in. Wide, 8.25 in. Deep TYPE HCP-SUh 800 A max. main circuit breaker 600 A max. branch circuit breaker FY, FA, FH, FI, KI, LA, LD, LG, LJ, LL, LH, LC, LX, LI, LXI, LE, MG, MJ, PG, PJ, PL, PGC, PJC, PLCj, QB, QD, QG, QJ, HD, HG, HJ, HL, JD, JG, JJ, JL S N FY, FA, FH, FI HD, HG, HJ, HL QB, QD, QG, QJ JD, JG, JJ, JL, KI MG, MJ, PG, PJ, PL PGC, PJC, PLC 800 A Max. Lugs or 800 A Max. Breaker Box Size: 26 in. Wide,.5 in. Deep Table.7: Interiors, Boxes and Fronts (100 A and 225 A interiors include solid neutral, all others without solid neutral. Order solid neutral from -23) Complete Front a Surface (4 Piece Trim) Interior Assembly (Less Branch (Less Branch 4 Piece Trim Breakers) Without Door b Breakers) Total Breaker Mounting Space (In.) s Ampere Type Type 1 3R/ 5/12 $ Price $ Price Trim With Door Type 1 $ Price $ Price Box c NEMA 3R/5/12d (Includes Front) HCN Lugs Only 3-poleSuitable for use as service equipment when provided with a main circuit breaker. i 225 A HCN14522N A HCN HCN52T( ) 41. HCN52T( )D 514. HC2652B 304. HC2652WP A HCN A HCN23652N A HCN HCN65T( ) 550. HCN65T( )D 663. HC2665B 304 HC2665WP A HCN A HCN32742N A HCN HCN74T( ) 743. HCN74T( )D 86. HC2674B 304. HC2674WP A HCN A HCN41832N A HCN HCN83T( ) 41. HCN83T( )D 1 HC2683B 304. HC2683WP A HCN A HCN5022N A HCN HCN2T( ) 41. HCN2T( )D 1 HC262B 304. HC262WP A HCN HCN Breaker ek Includes 3-pole, vertically mounted main circuit breakersuitable for use as service equipment A HCN14654M A HCN18651MN 371. HCN65T( ) 550. HCN65T( )D 663. HC2665B 304. HC2665WP A HCN18652MN A HCN23744M A HCN27741MN HCN74T( ) 743. HCN74T( )D 86. HC2674B 304. HC2674WP A HCN27742MN A HCN32832MN A HCN32834M HCN83T( ) 41. HCN83T( )D 1 HC2683B 304. HC2683WP A HCN4124M A HCN4522MN HCN2T( ) HCN2T( )D HC262B 304. HC262WP HCM Lugs Only 3-poleSuitable for use as service equipment when provided with a main circuit breaker. i 225 A HCM14482N A HCM A HCM HCM48T( ) 32. HCM48T( )D 483. HC3248B 243. HC3248WP A HCM A HCM23642N A HCM A HCM HCM64T( ) 516. HCM64T( )D 633. HC3264B 243. HC3264WP A HCM A HCM32732N A HCM A HCM HCM73T( ) 6. HCM73T( )D 864. HC3273B 243. HC3273WP A HCM A HCM5012N A HCM A HCM HCM1T( ) 6. HCM1T( )D HC321B 243. HC321WP A HCM HCM Breaker ek Includes 3-pole, vertically mounted main circuit breakersuitable for use as service equipment A HCM14644M A HCM18642MN HCM64T( ) 516. HCM64T( )D 633. HC3264B 243. HC3264WP A HCM18736MP A HCM18738MP HCM73T( ) 6. HCM73T( )D 864. HC3273DBm 243. Use HCP A HCM23734M A HCM27732MN HCM73T( ) 6. HCM73T( )D 864. HC3273B 243. HC3273WP A HCM3616MP A HCM3618MP HCM1T( ) 6. HCM1T( )D HC321DBm 243. Use HCP A HCM4114M HCM1T( ) 6. HCM1T( )D HC321B 243. HC321WP HCP-SU g Universal Single Row Lugs or Breaker k 3-poleSuitable for use as service equipment when provided with a main circuit breaker. i HCP54868SU HC2686T( )4P HC2686T( )HRf HC2686DB 243. HC2886WP a Add F for flush mount, S for surface mount. b Add-on door kit available from Peru. Example: For HCM48TS surface trim kit, order HCM48DS door kit. c For Type 1 applications, order interior, front, and box. For Type 3R/5/12 applications, order interior and box only. The front is included with the box. d Remove drain screws for Type 3R rating. e Bottom feed standard. f Hinged trim with door. g For main lugs panel, order sub-feed lug kit and back-feed as main lugs. h For main circuit breaker panel, order plug-on I-Line type PG, PJ, PL, MG, or MJ circuit breakers from -28 through -30 and backfeed as the main breaker (order solid neutral from -22). i Suitable for use as service equipment if equipped with an integral main circuit breaker or when not more than six main disconnecting means are provided and the panelboard is not used as a lighting and appliance branch circuit panelboard. j PG, PJ, PL circuit breakers are available with both thermal-magnetic equivalent and Micrologic trip. The Micrologic circuit breakers are available 80% and 100% rated. C suffix denotes a 100% rating. k breaker interrupt ratings, starting on Digest page 7-2. l m I-Line Surgelogic SPD not available. DB box is.5 inches deep. PENDING OBSOLESCENCE $ Price Box Height (In.) 2012 Schneider Electric PE1A Discount -21

22 I-Line Merchandised Panelboards TYPE HCP 800 A max. branch circuit breaker FAa, FH, FI, FY, QB, QD, QG, QJ, HD, HG, HJ, HL, JD, JG, JJ, JL, KI, LA, LD, LG, LJ, LL, LH, LC, LI, LX, LXI, LE, MG, MJ, PG, PJ, PL, PGC, PJC, PLCb FA, FH, FY HD, HG 1 2 Total HJ, HL Breaker QB, QD Mounting QG, QJ Space FI, KI, JD Each JG, JJ, JL Side LD, LG, LJ LL, LA, LH LC, LI, LX LXI, LE MG, MJ, PG, PJ, PL, PK, PGC PJC, PKC, PLC S N QB, QD QG, QJ FA, FH, FY HD, HG HJ, HL FI, KI, JD JG, JJ, JL 1200 A Max. Lugs or 800 A Max. Breaker Box Size: 42 in. Wide,.5 in. Deep a FA and JDA circuit breakers with field installable ground fault kits may be mounted in type HCP, HCP-SU, and HCR-U panelboards as shown, and require L-frame mounting space. b PG, PJ, and PL circuit breakers are available with both thermalmagnetic equivalent and Micrologic trip. The Micrologic circuit breakers are available 80% and 100% rated. C suffix denotes a 100% rating. TYPE HCR-U Universal s 1200 A max. branch circuit breaker FAc, FH, FI, FY, QB, QD, QG, QJ, HD, HG, HJ, HL, JD, JG, JJ, JL, KI, LA, LD, LG, LJ, LL, LH, LC, LI, LX, LXI, LE, MG, MJ, PG, PJ, PL, PGC, PJC, PLC, RGC, RJC, RLCde 1 2 Total Breaker Mounting Space Each Side FA, FH, FY HD, HG HJ, HL QB, QD QG, QJ FI, KI, JD JG, JJ, JL LD, LG, LJ LL, LA, LH LC, LI, LX LXI, LE MG, MJ PG, PJ, PK, PL, PGC, PJC, PKC, PLC RG, RJ, RK, RL, RGC, RJC RKC, RLC 1200 A Max. Lugs or 1200 A Max. Breaker QB, QD QG, QJ FA, FH, FY HD, HG HJ, HL FI, KI, JD JG, JJ, JL S/N Box Size: 44 in. Wide,.5 in. Deep c FA and JDA circuit breakers with field installable ground fault kits may be mounted in type HCP, HCP-SU, and HCR- U panelboards as shown, and require L-frame mounting space. d When RL main circuit breakers with equipment ground fault are applied on a 3Ø4W system, order solid neutral catalog number HCR12SNCT. The HCR12SNCT includes a neutral current transformer. e PG, PJ, and PL circuit breakers are available with both thermalmagnetic equivalent and Micrologic trip. The Micrologic circuit breakers are available 80% and 100% rated. C suffix denotes a 100% rating. Table.8: Total Breaker Mtg. Space (In.) s Amp. 600 Vac, 250 Vdc Class 2110 / Refer to 2110CT701 (1200 A Interiors Include solid neutral, all others without solid neutral. Order solid neutral from -23.) Max. No. of LC, MJ, PL, RL Breakers Complete Surface (4 Piece Trim) (Less Branch Breakers) Type 1 Interior Assembly (Less Branch Breakers) $ Price 4 Piece Trim Without Door g Front f $ Price Trim With Door $ Price Box h HCP Lugs Only3-pole Suitable for use as service equipment when provided with a main circuit breaker. i HCP HCP PL HCP HCW50T( ) 606. HCW50T( )D 743. HC4250DB HCP145012N HCP HCP PL HCP HCW5T( ) 671. HCW5T( )D 827. HC425DB HCP23512N HCP HCP PL HCP HCW68T( ) 846. HCW68T( )D HC4268DB HCP326812N HCP HCP PL HCP HCW86T( ) HCW86T( )D HC4286DB HCP508612N HCP BreakerjIncludes 3-pole Vertically mounted main circuit breakersuitable for use as service equipment HCP18686M LC HCP18688M HCW68T( ) 846. HCW68T( )D HC4268DB HCP36866M LC HCP36868M HCW86T( ) HCW86T( )D HC4286DB HCR-U Universal Lugs or Breakerj3-pole Suitable for use as service equipment when provided with a main circuit breaker. For Lugs panel, order sub-feed lug kit catalog number S3330 and back feed as main lugs. For Breaker panel, order plug-on I-Line type PG, PJ, PL, RGC, RJC, or RLCk circuit breakers from pages -27 through -2, and back feed as the main circuit breaker. (Order solid neutral separately) 108 l PL or 3RLC HCR548612U HCR86T( )m HCR86T( )D HC4486DB $ Price Box Height (In.) f Add F for flush mount, S for surface mount. g Add-on door kit available. Example: For HCW50TS trim kit, order HCW50D door kit. h See Digest page -23 for 42 in. wide weatherproof enclosures. i Suitable for use as service equipment if equipped with an integral main circuit breaker or when not more than six main disconnecting means are provided and the panelboard is not used as a lighting and appliance branch circuit panelboard. j breaker interrupt ratings, starting on Digest page 7-2. k When RL main circuit breakers with equipment ground fault are applied on a 3Ø4W system, order solid neutral catalog number HCR12SNCT. The HCR12SNCT includes a neutral current transformer. l 15 in. of mounting space is taken up by the back fed main lug kit or RG, RJ, RL main circuit breaker, leaving 3 in. of branch circuit breaker mounting space. m Add-on door kit available. Example: For HCR86TS trim kit, order HCW86D door kit. Table.: Type of Breaker Breaker / Sub-feed Lug Kit Mounting Space Requirement Maximum Ampacity No. of Poles Inch Mounting Requirements Type of Breaker Maximum Ampacity No. of Poles Inch Mounting Requirements FY 30 A QB, QD, QG, QJ 225 A FA, FH JD, JG, JJ, JL, KI, SL A 4.5 FA, FH 2 3 LA, LH, SL A A FA, FH, SL LD, LG, LJ, LL 600 A 6 FI 2, LC, LI, LXI 600 A 7.5 2, 3 HD, HG 2 3 MG, MJ, MA, MH, SL800, PGC, PJC, PLC 800 A HD, HG 150 A HJ, HL 2, PG, PJ, PL, S A QB, QD, QG, QJ 225 A 2 3 RG, RJ, RL, RGC, RJC, RLC, S A 15 Table.100: Breaker Interiors Standard Frame Types n Breaker Ampacity Panelboard Type Factory Supplied Breaker 100 HCN FA HCN, HCM JDA HCN LAP36400MB HCM LAP36400MB 600 MGP36600 or 800 HCM, HCP or MGP36800 n breaker interrupt ratings, starting on Digest page 7-2. Table.101: Standard Copper Bus Interiors Type Ampacity HCN 600 HCM, HCP-SU 800 HCP, HCR-U 800 and Above Note: Merchandised copper interiors are not available in all ampacities. For example, if the application calls for a HCN 225 A copper bus interior, order an HCN 600 A interior Schneider Electric PE1A Discount

23 I-Line Merchandised Panelboards Accessories Class 60, 2110 / Refer to 2110CT701 Blank Fillers Equipment Ground Bar Solid Neutral Blank Extensions Sub-feed Lug Kits Table.102: I-Line Merchandised Panelboard Accessories Description No. Blank Fillers1.5 in. (minimum order 3) e HNM1BL Blank Fillers4.5 in. (minimum order 5) e HNM4BL Solid Neutral Assemblies 225 A HC2SN A HC4SNa, HCW4SNb A HC6SNa, HCW6SNb HC8SNa, HCW8SNb A HCPSU8SNc HCPSU8SNCTc A HCW12SNb A, for use with HCR-U universal panel only HCWM12SNd A, Including neutral CT for 3Ø4W systems HCR12SNCTd Equipment Ground Bar KitsHCN PK27GTA HCM, HCP, HCR-U PK32DGTA Blank Extensions (For replacement purposes) 1.5 in. for mounting on wide side of I-Line panelboard (minimum order 3) e HLW1BL in. for mounting on wide side of I-Line panelboard (minimum order 5) e HLW4BL in. for mounting on narrow side of I-Line panelboard (minimum order 3) e HLN1BL in. for mounting on narrow side of I-Line panelboard (minimum order 5) e HLN4BL in. for mounting on wide side of I-Line panelboard (minimum order 5) e HLW4EBL in. for mounting on narrow side of I-Line panelboard (minimum order 5) e HLN4EBL a Used on Type HCN, HCM. b Used on 400 A, 600 A, 800 A, and 1200 A HCP (main lugs), and 600 A and 800 A (main circuit breaker). c Used on Type HCP-SU. d Used on Type HCR-U. e Blank extension pricing is per unit. Multiply the list price by the quantity ordered. Note minimum order quantity. Table.103: Blank Extensions Application Breaker Mounting Ht. Branch Side All applications, except Powerpact H/J with Micrologic trip unit 5/6 1.5 in. HLW1BL Wide Side 4.5 in. HLW4BL All applications, except Powerpact H/J with Micrologic trip unit 5/6 1.5 in. Narrow Side HLN1BL 4.5 in. HLN4BL Only Powerpact H/J circuit breakers with Micrologic trip unit 5/6 4.5 in. Narrow Side HLN4EBL Only Powerpact H/J circuit breakers with Micrologic trip unit 5/6 4.5 in. Wide Side HLW4EBL Table.104: Panelboard Adapter Kits Crimp Lug Adapter Kits f I-Line Panelboard Type HCN HCM HCP, HCR-U g 400 A HCN400VCA HCM400VCA HCW400VCA A HCN600VCA HCM600VCA HCW600VCA A HCM800VCA HCW800VCA A HCW1200VCA 41. f For use with MLO panel, order VCEL lugs seperately. g Not for use with P- or R-frame circuit breakers or sub-feed kits S3330 or S3331. Table.105: Type 3R/5/12 Enclosures Interior Type Dimensions (In.) H W D HC4250WP HCP HC425WP HCP HC4268WP HCP HC4286WP HCP HC4486WP HCR-U Table.106: Box Extensions Interior Type Extension HC260DEX (F or S) HCP-SU in HC260EX (F or S) HCN in HC320EX (F or S) HCM in HC4212DEX (F or S) HCP 12 in HC4406DEX (F or S) HCR-U 6 in HC4412DEX (F or S) HCR-U 12 in Table.107: Sub-feed Lug Kits hi Ampere Height 2012 Schneider Electric $ Price Max. Short System s RMS Symmetrical Amperes Protected by Breaker For Use in I-Line Panelboard Types In. (mm) 240 Vac 480 Vac 600 Vac 100 A SL K 65 K 18 K FA, FH, FD, FG, FJ HCN, HCM, HCP, HCP-SU, HCR-U 250 A SL K 200 K 100 K FA, FD, FG, FH, FJ, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, KI HCM, HCP, HCP-SU, HCR-U 400 A SL400j K 200 K 100 K FA, FD, FG, FH, FJ, KA, KH, KC, KI, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, LA, LH, LC, LX, LI, LXI, DG, DJ, DL, LD, LG, LJ, LL, LR ( L & D Frame 400 A Max.) HCP, HCP-SU, HCR-U (wide side only) 800 A 22 SL K 100 K 50 K FA, FD, FG, FH, FJ, KA, KH, KC, KI, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, LA, LH, LC, LX, LX, LI, LXI, MA, MH, MX, DG, DJ, DL, LD, LG, LJ, LL, LR HCM, HCP, HCP-SU, HCR-U 800 A 22 SL800M K 100 K 25 K FA, FD, FG, FH, FJ, KA, KH, KC, KI, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, MA, MH, MX, MG, PG, MJ, PJ, PK, PL, DG, DJ, DL, LD, LG, LJ, LL, LR HCM, HCP, HCP-SU, HCR-U 1200 A 22 S K 100 K 50 K FA, FD, FG, FH, FJ, KA, KH, KC, KI, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, LA, LH, LC, LX, LI, LXI, MA, MH, MX, MG, PG, MJ, PJ, PK, PL, DG, DJ, DL, LD, LG, LH, LL, LR HCP, HCP-SU, HCR-U 1200 A S K 100 K 50 K FA, FD, FG, FH, FJ, KA, KH, KC, KI, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, LA, LH, LC, LX, LI, LXI, MA, MH, MX, NA, NC, NX, MG, PG, MJ, PH, PK, PL, RG, RJ, RL, RK, DG, DJ, DL, LD, LG, LJ, LL, LR HCR-U 1200 A 22 SL1200P5, SL1200P6, K 100 K 50 K FA, FD, FG, FH, FJ, KA, KH, KC, KI, HD, HG, HJ, HL, HR, JD, JG, JJ, JL, JR, MG, PG, MJ, PJ, PK, SL1200P7 PL, RG, RJ, RL, RK, DG, DJ, DL, LD, LG, LJ, LL, RL HCP, HCP-SU, HCR-U h Plug-on in same manner as a branch circuit breaker NOTE: S3330, S3331, SL1200P5, SL1200P6, SL1200P7, SL Kits are rated 1200 A and i For other ratings, See the I-Line Information Manual, # xx. may be applied to 1200 ampere loads when installed into HCRU panelboards. j SL400 cannot be used in HCM panelboards due to inadequate wire bending space. However, when instaled into HCP and HCPSU panelboards they are only rated 800 amperes maximum due to restricted wire bending space. For Surgelogic I-Line plug-on SPD unit pricing and information, see Digest pages 6-3 and 6-4. For field-installable I-Line door kits, see the Supplemental and Obsolescence Digest, Section 4. Table.108: Sub-feed Lug kit terminal data No. (Prefix) No. Poles Ampere Std. Lug Kit No. Standard Lug Wire Size k SL A AL100FA #14 1/0 AWG Cu or #12 1/0 AWG Al SL A #4 AWG 300 kcmil SL A AL400LA one #1 AWG 600 kcmil or two #1 AWG 250 kcmil SL A AL00MA (3) #3/0 AWG 500 kcmil S A AL1200P24K (4) #3/0 AWG 500 kcmil S A AL1200R53K (4) #3/0 AWG 600 kcmil k Unless otherwise specified, wire sizes apply to both aluminum and copper conductors. -23

24 Breakers F-frame, PowerPact D-frame for I-Line Panelboards and Switchboards Table.10: QO Distribution Panel240 Vac Max. Only Mounts in Type HCN, HCM, HCP, HCP-SU, or HCR-U I-Line panelboards, 30 A max. branch circuit breaker. Order QO plug-on circuit breakers from page -34. Maximum No. 1-pole Phase QO Breakers Connection a Mounting Height In. mm 2-pole F-frame accessories starting on Supplemental Digest page 3-24 F-frame dimensions Digest page 7-54 F-frame optional lugs Digest page 7-51 PowerPact D-frame Mission Critical Breakers When the D-frame Mission Critical circuit breaker is used as a main circuit breaker with QO branch circuit breakers, the D-frame MC will remain closed during any fault that occurs downstream of the QO circuit breaker up to 30kA at 208Y/120 Vac. c D-frame circuit breakers 400 A and below are 100% rated. D-frame accessories, lugs..... starting on Supplemental Digest page 3-27 D-frame dimensions Digest page pole a 6 AB HQO206AB BC HQO206BC AC HQO206AC ABC HQO Includes (5) QO1DB dummy circuit breakers. FA/FH, 1-pole 1.5 in (38 mm) Mounting Height Table.110: Example: FJA, 20 A 1-pole, 277 Vac and 70 A 2- and 3-pole QB 240 Vac. Use phase option number for HD, HG, HJ, HL, JD, JG, JJ, JL, MG, and MJ. Phase Option Phase Connection FA/FH, 2-pole 3 in (76 mm) Mounting Height FA/FH, 3-pole 4.5 in (114 mm) Mounting Height 1-pole 2-pole 3-pole 1 A FJA B FJA C FJA AB QBA AC QBA BA QBA BC QBA CA QBA CB QBA Standardb ABC QBA CBA QBA b The absence of a phase option number after a 3-pole catalog number will result in an ABC phase connection. Table.111: Example: FA, 30 A, 480 Vac. Use phase option letters for FH, FI, KI, LA, LH, LC, and LI. Phase Option Letter 1-pole 2-pole 3-pole A FA14035A B FA14035B C FA14035C AB FA24030AB AC FA24030AC BC FA24030BC ABC FA34030 CBA FA34030CBA Table.112: Interrupt s (ka) FA (240 V) FA (480 V) FJ 240 V (1P), 25 (2, 3P) V V V Table.113: PowerPact D-frame, A Mission Critical Breaker Cat.alog c Continuous Current Terminal Wire Range (AWG/kcmil) DJA32150W 150 A DJA32250W 250 A #2-600 Cu or #2-500 Al DJA32400W 400 A DJA32600W 600 A (2) 2/0-350 Cu or (2) 2/0-500Al Class 650, 651 Table.114: F-frame100 A, Thermal-magnetic (240 Vac) Schneider Electric DE2 Discount Ampere AC Magnetic Trip Settings Standard Interrupting Hold Trip Terminal Wire Range 2-pole, 240 Vac d 15 A FA22015( ) 20 A FA22020( ) AL50FA #14 #4 AWG Cu or 25 A FA22025( ) #12 #4 AWG Al 30 A FA22030( ) 35 A FA22035( ) A FA22040( ) A FA22045( ) 50 A FA22050( ) AL100FA 60 A FA22060( ) #14 #1/0 AWG Cu 70 A FA22070( ) or #12 #1/0 AWG Al 80 A FA22080( ) A FA2200( ) A FA22100( ) 3-pole, 240 Vac 15 A FA A FA32020 AL50FA #14 #4 AWG Cu or 25 A FA32025 #12 #4 AWG Al 30 A FA A FA A FA32040 AL100FA #14 #1/0 AWG Cu 45 A FA32045 or #12 #1/0 AWG Al 50 A FA A FA AL100FA 70 A FA32070 #14 #1/0 AWG Cu A FA32080 or #12 #1/0 AWG Al 0 A FA3200 AL100FA A FA32100 #14 #1/0 AWG Cu d 1- and 2-pole circuit breaker catalog numbers are completed by adding the required phase connection letters as a suffix. Table.115: F-frame100 A, Thermal-magnetic (480 Vac) Ampere AC Magnetic Trip Settings Hold Trip Standard Interrupting Extra High Interrupting Terminal Wire Range FY/FA Lugs FJ/FC Lugs 1-pole, 277 Vac, 125 Vdc e 15 A FY14015( )f FJA14015( ) AL50FA AL30FD 20 A FY14020( )f FJA14020( ) #14-#4 #12 # AWG Cu, or AWG Al, or 25 A FY14025( )f FJA14025( ) #12-#4 #14 #6 30 A FY14030( )f FJA14030( ) AWG Al AWG Cu 35 A FA14035( )g FJA14035( ) 40 A FA14040( )g FJA14040( ) A FA14045( )g FJA14045( ) AL100FA AL100FD 50 A FA14050( )g FJA14050( ) #14 #1/0 #12 #2/0 AWG Cu or AWG Al 60 A FA14060( )g FJA14060( ) 651. #12 #1/0 or 70 A FA14070( )g 302. FJA14070( ) 720. AWG Al #14 #2/0 80 A FA14080( )g AWG Cu 0 A FA1400( )g A FA14100( )g 2-pole, 480 Vac, 250 Vdc efg 15 A FA24015( ) AL50FA CU30FA4 20 A FA24020( ) #14 # one #14 AWG Cu or 25 A FA24025( ) #10 AWG #12 #4 30 A FA24030( ) Cu only AWG Al 35 A FA24035( ) 40 A FA24040( ) A FA24045( ) AL100FA AL100FA4 50 A FA24050( ) #14 #1/0 one #14 #3 AWG Cu or AWG Cu 60 A FA24060( ) 651. #12 #1/0 or 70 A FA24070( ) 833. AWG Al one #12 #1 80 A FA24080( ) AWG Al 0 A FA2400( ) A FA24100( ) 3-pole, 480 Vac, 250 Vdc e 15 A FA34015 AL50FA CU30FA4 20 A FA34020 #14 # one #14 25 A FA34025 AWG Cu or #10 AWG #12 #4 30 A FA34030 Cu only AWG Al 35 A FA A FA A FA34045 AL100FA AL100FA4 50 A FA34050 #14 #1/0 one #14 #3 AWG Cu or AWG Cu 60 A FA #12 #1/0 or 70 A FA AWG Al one #12 #1 80 A FA34080 AWG Al 0 A FA A FA34100 e 1- and 2-pole circuit breaker catalog numbers are completed by adding the required phase connection letters as a suffix. f Rated 277 Vac 15 and 20 A FY circuit breakers are rated for switching duty (SWD). 15, 20, 25, and 30 A FA I-Line circuit breakers are also available (no SWD rating). g Rated 277 Vac, 125 Vdc, except FY circuit breakers, which have no dc rating A circuit breakers suitable for use with 60 o C or 75 o C conductors A circuit breakers are suitable for use with 75 o C conductors.

25 Breakers F-frame, PowerPact Q-frame for I-Line Panelboards and Switchboards Class 650, 734, 820 FI and 3-pole 4.5 in (114 mm) Mounting Height Table.116: F-frame100 A, Thermal-magnetic (600 Vac) Ampere AC Magnetic Trip Settings Standard Interrupting High Interrupting Current Limiting Terminal Wire Hold Trip Range 1-pole, 277 Vac, 125 Vdc a 15 A FH16015( ) 20 A FH16020( ) A FH16025( ) 30 A FH16030( ) 35 A FH16035( ) 40 A FH16040( ) A FH16045( ) 50 A FH16050( ) 60 A FH16060( ) A FH16070( ) A FH16080( ) 0 A FH1600( ) A FH16100( ) 2-pole, 600 Vac, 250 Vdc a 15 A FA26015( ) FH26015( ) 20 A FA26020( ) FH26020( ) FI26020( ) A FA26025( ) FH26025( ) 30 A FA26030( ) FH26030( ) FI26030( ) A FA26035( ) FH26035( ) 40 A FA26040( ) FH26040( ) FI26040( ) A FA26045( ) FH26045( ) 50 A FA26050( ) FH26050( ) FI26050( ) A FA26060( ) 780. FH26060( ) FI26060( ) 70 A FA26070( ) FH26070( ) FI26070( ) A FA26080( ) FH26080( ) FI26080( ) 0 A FA2600( ) FH2600( ) FI2600( ) A FA26100( ) FH26100( ) FI26100( ) pole, 600 Vac, 250 Vdc 15 A FA36015 FH A FA36020 FH36020 FI A FA36025 FH A FA36030 FH36030 FI A FA36035 FH A FA36040 FH36040 FI A FA36045 FH A FA36050 FH36050 FI A FA FH FI A FA36070 FH36070 FI A FA36080 FH36080 FI A FA3600 FH3600 FI A FA36100 FH36100 FI AL50FA #14 #4 AWG Cu or #12 #4 AWG Al AL100FA #14 #1/0 AWG Cu or #12 #1/0 AWG Al AL50FA #14 #4 AWG Cu or #12 #4 AWG Al AL100FA #14 #1/0 AWG Cu or #12 #1/0 AWG Al AL50FA #14 #4 AWG Cu or #12 #4 AWG Al AL100FA #14 #1/0 AWG Cu or #12 #1/0 AWG Al a 1- and 2-pole circuit breaker catalog numbers are completed by adding the required connection letters as a suffix, See Digest page -24. NOTE: As of January 1st, FI breakers will only fit on the wide side of I-Line panelboards. QB/QD/QG/QJ Mounting Height: 2-pole3 in (76 mm) 3-pole4.5 in (114 mm) Table.117: PowerPact Q-frame b 225 A, Thermal-magnetic (240 Vac) Ampere AC Magnetic Trip Settings "B" Interrupting "D" Interrupting "G" Interrupting "J" Interrupting Hold Trip 2-pole, 240 Vac c 70 A QBA22070( ) QDA22070( ) QGA22070( ) QJA22070( ) 80 A QBA22080( ) 600. QDA22080( ) QGA22080( ) 153. QJA22080( ) A QBA2200( ) QDA2200( ) QGA2200( ) QJA2200( ) 100 A QBA22100( ) QDA22100( ) QGA22100( ) QJA22100( ) 110 A QBA22110( ) QDA22110( ) QGA22110( ) QJA22110( ) 125 A QBA22125( ) QDA22125( ) QGA22125( ) QJA22125( ) 150 A QBA22150( ) 600. QDA22150( ) QGA22150( ) 153. QJA22150( ) A QBA22175( ) QDA22175( ) QGA22175( ) QJA22175( ) 200 A QBA22200( ) QDA22200( ) QGA22200( ) QJA22200( ) 225 A QBA22225( ) QDA22225( ) QGA22225( ) QJA22225( ) 3-pole, 240 Vac d 70 A QBA32070( ) QDA32070( ) QGA32070( ) QJA32070( ) 80 A QBA32080( ) 113. QDA32080( ) 206. QGA32080( ) QJA32080( ) A QBA3200( ) QDA3200( ) QGA3200( ) QJA3200( ) 100 A QBA32100( ) QDA32100( ) QGA32100( ) QJA32100( ) 110 A QBA32110( ) QDA32110( ) QGA32110( ) QJA32110( ) 125 A QBA32125( ) QDA32125( ) QGA32125( ) QJA32125( ) 150 A QBA32150( ) 113. QDA32150( ) 206. QGA32150( ) QJA32150( ) A QBA32175( ) QDA32175( ) QGA32175( ) QJA32175( ) 200 A QBA32200( ) QDA32200( ) QGA32200( ) QJA32200( ) 225 A QBA32225( ) QDA32225( ) QGA32225( ) QJA32225( ) b Replacement lugs are not available on QB, QD, QG, or QJ circuit breakers. Lugs for QB, QD, QG, or QJ circuit breakers accept one #4 AWG 300 kcmil. No accessories are available for PowerPact Q Frame breakers. c 2-pole QB, QD, QG, and QJ circuit breakers are completed by adding the required phasing numbers as indicated in the parentheses, See Digest page -24. d 3-pole QB, QD, QG, and QJ circuit breakers for ABC phasing are complete without additional phasing number. For CBA phasing, complete the catalog number by inserting the number 6 in the parentheses. Table.118: Interrupt s (ka) FA FH FI QB QD QG QJ e 240 V (1P A), 65 (1P A, 2P, 3P) V (2, 3P) 600 V (2, 3P) 100 e 3-pole QJ circuit breakers are rated at 208Y/120 Vac only. F-frame accessories starting on Supplemental Digest page 3-24 F-frame dimensions digest page 7-54 F-frame optional lugs digest page 7-51 Q-frame accessories Digest page starting on Supplemental Digest page 3-24 Q-frame dimensions Digest page 7-54 Q-frame optional lugs Supplemental Digest page Schneider Electric DE2 Discount -25

26 Breakers H- and J-frame for I-Line Panelboards and Switchboards Class Table.11: H-frame 150 A Thermal-Magnetic UL Current-Limitinga Breakers (600 Vac, 250 Vdc) With Factory Sealed Trip Unitb Suitable for Reverse Connectionb Interrupting (2nd Letter of ) Current Fixed AC Trip D G Ja La Cat. No.c 40 o C Hold Trip 80% Rated 80% Rated 80% Rated 80% Rated H-frame, 150A 2P, 600 Vac 50/60 Hz, 250 Vdca 15 A 350 A 750 A H( )A26015( ) A 350 A 750 A H( )A26020( ) A 350 A 750 A H( )A26025( ) A 350 A 750 A H( )A26030( ) A 400 A 850 A H( )A26035( ) A 400 A 850 A H( )A26040( ) A 400 A 850 A H( )A26045( ) A 400 A 850 A H( )A26050( ) A 800 A 1450 A H( )A26060( ) A 800 A 1450 A H( )A26070( ) A 800 A 1450 A H( )A26080( ) A 800 A 1450 A H( )A2600( ) A 800 A 1700 A H( )A26100( ) A 00 A 1700 A H( )A26110( ) A 00 A 1700 A H( )A26125( ) A 00 A 1700 A H( )A26150( ) H-frame 150A 3P, 600 Vac 50/60 Hz, 250 Vdc 15 A 350 A 750 A H( )A A 350 A 750 A H( )A A 350 A 750 A H( )A A 350 A 750 A H( )A A 400 A 850 A H( )A A 400 A 850 A H( )A A 400 A 850 A H( )A A 400 A 850 A H( )A A 800 A 1450 A H( )A A 800 A 1450 A H( )A A 800 A 1450 A H( )A A 800 A 1450 A H( )A A 800 A 1700 A H( )A A 00 A 1700 A H( )A A 00 A 1700 A H( )A A 00 A 1700 A H( )A a 2 pole circuit breaker catalog numbers are completed by adding the required phase connection number as a suffix see Table.128. Terminal Wire Range AL150HD 14 3/0 AWG AL150HD 14 3/0 AWG Table.120: J-frame 250 A Thermal-Magnetic UL Current-Limitinga Breakers (600 Vac, 250 Vdc) With Factory Sealed Trip Unitb Suitable for Reverse Connectionb Interrupting (2nd Letter of ) Current Adjustable AC Trip D G Ja La Ra 40 o Cat. No.c Terminal C Wire Range Low High 80% Rated 80% Rated 80% Rated 80% Rated 80% Rated J-frame 250A 2P, 600 Vac 50/60 Hz, 250 Vdca 150 A 750 A 1500 A J( )A26150( ) AL175JD 175 A 875 A 1750 A J( )A26175( ) /0 AWG 200 A 1000 A 2000 A J( )A26200( ) AL250JD 225 A 1125 A 2250 A J( )A26225( ) /0 AWG 350 kcmil 250 A 1250 A 2500 A J( )A26250( ) J-frame 250A 3P, 600 Vac 50/60 Hz, 250 Vdc 150 A 750 A 1500 A J( )A AL175JD 175 A 875 A 1750 A J( )A /0 AWG 200 A 1000 A 2000 A J( )A AL250JD 225 A 1125 A 2250 A J( )A /0 AWG 350 kcmil 250 A 1250 A 2500 A J( )A a 2 pole circuit breaker catalog numbers are completed by adding the required phase connection number as a suffix see Table.128. Table.121: H-frame 150 A and J-frame 250 A Electronic Trip UL Current-Limitinga Breakers (600 Vac) With Factory Sealed Trip Unitb Suitable for Reverse Connection d Electronic Trip Unit Type Function Trip Unit 600 Vac, 50/60 Hz, 3P Micrologic Standard Micrologic Ammeter Micrologic Energy Micrologic Ammeter Micrologic Energy LI 3.2g LSI 3.2Sg LSI 5.2A LSI 5.2E LSIG 6.2A LSIG 6.2E Sensor Cat. No.c Interrupting (2nd Letter of ) D G Ja La Ra 80% Rated 80% Rated 80% Rated 80% Rated 80% Rated Terminal 60 A H( )A36060U31X A H( )A36100U31X AL150HDe 150 A H( )A36150U31X A J( )A36250U31X AL250JDf 60 A H( )A36060U33X A H( )A36100U33X AL150HDe 150 A H( )A36150U33X A J( )A36250U33X AL250JDf 60 A H( )A36060U43X A H( )A36100U43X AL150HDe 150 A H( )A36150U43X A J( )A36250U43X AL250JDf 60 A H( )A36060U53X A H( )A36100U53X AL150HDe 150 A H( )A36150U53X A J( )A36250U53X AL250JDf 60 A H( )A36060U44X A H( )A36100U44X AL150HDe 150 A H( )A36150U44X A J( )A36250U44X AL250JDf 60 A H( )A36060U54X A H( )A36100U54X AL150HDe 150 A H( )A36150U54X A J( )A36250U54X AL250JDf a breakers with J, L, and R interrupting ratings are UL certified as current limiting. b See Supplemental Digest pages 3-2 and 3-3 for circuit breakers with field-interchangeable trip units c To complete catalog number, replace the blank with the appropriate rating (D, G, J, L). d For applications requiring communications, see Digest page 7-4. e AL150HD wire range is 14 3/0 AWG. f AL250JD wire range is 3/0 AWG 350 kcmil. For smaller wire range (4 4/0 AWG ), replace the lug s wire binding screws with the larger binding screws provided. g 3P circuit breakers with this trip unit can be used for 2P applications Schneider Electric DE2 Discount

27 Breakers K-, PowerPact H-, J-, L-frame for I-Line Panelboards and Switchboards Class 825, 0612 Table.122: K-frame250 A, Thermal-magnetic, Current Limiting (600 Vac) KI and 3-pole 4.5 in (114 mm) Mounting Height Ampere J-Frame Mission Critical Breaker AC Magnetic Trip Settings Current Limiting Terminal Wire Range Low High 2-pole, 600 Vac, 250 Vdc a 110 A KI26110( ) AL250KA 125 A KI26125( ) one #4 AWG 150 A KI26150( ) kcmil 175 A KI26175( ) A KI26200( ) AL250KI 225 A KI26225( ) one #1/0 AWG 250 A KI26250( ) kcmil 3-pole, 600 Vac, 250 Vdc 110 A KI AL250KA 125 A KI one #4 AWG 150 A KI kcmil 175 A KI A KI AL250KI 225 A KI one #1/0 AWG 250 A KI kcmil a 2-pole circuit breaker catalog numbers are completed by adding required phase connection letters as suffix to catalog number. See Digest page -24. Table.123: J-frame 250 A Electronic Trip Mission Critical Breakers (480/277 Vac) With Factory Sealted Trip Units Suitable for Reverse Connectiona Electronic Trip Trip Unit Type Function Trip Unit Continuous D Interrupting G Interrupting J Interrupting L Interrupting Current Cat. No. Cat. No. Cat. No. Cat. No. Terminal Standard LI 3.2 W 250 JDA34250WU31X 361. JGA34250WU31X JJA34250WU31X JLA34250WU31X 875. AL250JDb Standard LSI 3.2S-W 250 JDA34250WU33X 331. JGA34250WU33X 516. JJA34250WU33X 711. JLA34250WU33X 071. AL250JDb High Perf. Ammerter LSI 5.2A-W 250 JDA34250WU43X 43. JGA34250WU43X JJA34250WU43X JLA34250WU43X AL250JDb High Perf. Energy LSI 5.2E-W 250 JDA34250WU53X JGA34250WU53X JJA34250WU53X JLA34250WU53X AL250JDb High perf. Ammerter LSIG 6.2A-W 250 JDA34250WU44X JGA34250WU44X JJA34250WU44X 336. JLA34250WU44X AL250JDb High Perf. Energy LSIG 6.2E-W 250 JDA34250WU54X JGA34250WU54X 71. JJA34250WU54X 42. JLA34250WU54X AL250JDb a Standard rated (80%). Not available in 100% rated. b AL250JD terminal wire range is (1) 3/0 AWG 350 kcmil. L-Frame Mission Critical Breaker Table.124: L-frame 600 A Electronic Trip Mission Critical Breakers (480/277 Vac) With Factory Sealted Trip Units Suitable for Reverse Connectiona Electronic Trip Trip Unit Type Function Trip Unit Continuous D Interrupting G Interrupting J Interrupting L Interrupting Current Cat. No. Cat. No. Cat. No. Cat. No. Terminal 250 LDA34250WU31X 51. LGA34250WU31X 621. LJA34250WU31X 102. LLA34250WU31X 118. AL400L61K3b Standard LI 3.3 W 400 LDA34400WU31X 51. LGA34400WU31X 621. LJA34400WU31X 102. LLA34400WU31X LDA34600WU31X LGA34600WU31X 126. LJA34600WU31X LLA34600WU31X AL600LF52K3c 250 LDA34250WU33X LGA34250WU33X 60. LJA34250WU33X 10. LLA34250WU33X AL400L61K3b Standard LSI 3.3S-W 400 LDA34400WU33X LGA34400WU33X 60. LJA34400WU33X 10. LLA34400WU33X LDA34600WU33X 34. LGA34600WU33X 826. LJA34600WU33X LLA34600WU33X AL600LF52K3c High Perf. Ammeter LSI 5.3A-W LDA34400WU43X LDA34600WU43X LGA34400WU43X LGA34600WU43X LJA34400WU43X LJA34600WU43X LLA34400WU43X LLA34600WU43X AL600LF52K3c High Perf. Energy LSI 5.3E-W LDA34400WU53X LDA34600WU53X LGA34400WU53X LGA34600WU53X LJA34400WU53X LJA34600WU53X LLA34400WU53X LLA34600WU53X AL600LF52K3c High Perf. Ammeter LSIG 6.3A-W LDA34400WU44X LDA34600WU44X LGA34400WU44X LGA34600WU44X LJA34400WU44X LJA34600WU44X LLA34400WU44X LLA34600WU44X AL600LF52K3c High Perf. Energy LSIG 6.3E-W LDA34400WU54X LDA34600WU54X LGA34400WU54X LGA34600WU54X LJA34400WU54X LJA34600WU54X LLA34400WU54X LLA34600WU54X AL600LF52K3c a Standard rated (80%). Not available in 100% rated. b AL400L61K3 terminal wire range is (1) #2 AWG 500 kcmil Al or #2 AWG 600 kcmil Cu.. c AL600LF52K3 terminal wire range is (2) #3/0 AWG 500 kcmil. Table.125: PowerPact H-, J-, and L-frame Automatic Molded Case Switches, 600 Vac Breaker Poles Ampere G Withstand L Withstand R Withstand Cat. No. Trip Point Cat. No. Trip Point Cat. No. Trip Point H-frame J-frame 2a 3 Terminal Wire Range 150 A HGA26000S15( ) A HLA26000S A 175 A JGA26000S17( ) A JLA26000S A 250 A JGA26000S25( ) A JLA26000S A 150 A HGA36000S A HLA36000S A HRA36000S A AL150HD 14 AWG 3/0 AWG Al/Cu 175 A JGA36000S A JLA36000S A JRA36000S A AL175JD 4 4/0 AWG Al/Cu 250 A JGA36000S A JLA36000S A JRA36000S A AL250JD 3/0 AWG 350 kcmil Al/Cu L-frame A LGA36000S40X A LLA36000S40X A LRA36000S40X A AL150HD AL600LS52K3 600 A LGA36000S60X A LLA36000S60X A LRA36000S60X A AL250JD (2) 2/0 AWG 500 kcmil Al/Cu a 2-pole circuit breaker catalog numbers are completed by adding the required phase connection number as a suffix, see Table.128. Table.126: KI Interrupt s (ka) V KI K-frame accessories starting on Supplemental Digest page 3-25 K-frame dimensions Supplemental Digest page 3-33 K-frame optional lugs Supplemental Digest page 3-28 H-, J-, and L-frame accessories starting on Digest page 7-36 H-, J-, and L-frame dimensions starting on Digest page 7-54 H-, J-, and L-frame optional lugs digest page 7-3 Table.127: Interrupt s (ka) D G J L 240 V V Table.128: Phase OptionsExample HDA26150( ) Phase Option Phase Connection 2-pole 3-pole 1 AB HDA AC HDA BA HDA BC HDA CA HDA CB HDA Standard ABC JDA34250WU31X 6 CBA JDA34250WU31X Schneider Electric DE2 Discount -27

28 Breakers LA Mission Critical for I-Line Panelboards and Switchboards Class 660, 665, 670, LA Mission Critical Breakers The LA High Magnetic Withstand MC Breakers are designed to trip at a higher magnetic trip level (18 20 times handle rating) than typical molded case circuit breakers (MCCBs) (which trip at 5 10 times the handle rating). The high magnetic withstand value of these LA circuit breakers allow the downstream branch circuit breaker to clear the fault. Table.12: L-frame400 A, I-Line LA/LH MC High Magnetic Withstand Breaker For Mission Critical Loads Ampere AC Magnetic Level Factory Set a Standard Interrupting High Interrupting Terminal Hold Trip Cat. No. Cat. No. Cat. No. Wire Range LA/LH MC Breaker, 3P, 480 Vac 200 A 225 A 3400 A 3825 A 4000 A 4500 A LA34200MC LA34225MC LH34200MC LH34225MC AL250LAMC 250 A 4250 A 5000 A LA34250MC LH34250MC A 6000 A 7200 A LA34400MC 641. LH34400MC AL400LA a AC magnetic setting tolerances are +0-25% from maximum value shown. (1) kcmil Al (1) 3/0 AWG 350 kcmil Cu (1) 1 AWG 600 kcmil Al or (2) 1 AWG 250 kcmil Al LA/LH 2- and 3-pole 6 in (152 mm) Mounting Height LI 2- and 3-pole 7.5 in (10 mm) Mounting Height LC 2- and 3-pole 7.5 in (10 mm) Mounting Height Table.130: L-frame400 A, Thermal-magnetic (600 Vac) Ampere AC Magnetic Trip Settings Standard Interrupting High Interrupting Terminal Wire Range Low High 2-pole, 600 Vac, 250 Vdc b 125 A LA26125( ) LH26125( ) A LA26150( ) LH26150( ) A LA26175( ) LH26175( ) A LA26200( ) LH26200( ) A LA26225( ) LH26225( ) A LA26250( ) LH26250( ) A LA26300( ) LH26300( ) A LA26350( ) LH26350( ) A LA26400( ) LH26400( ) pole, 600 Vac, 250 Vdc 125 A LA LH A LA LH A LA LH A LA LH A LA LH A LA LH A LA LH A LA LH A LA LH Table.131: L-frame600 A, Thermal-magnetic (600 Vac)c AC Magnetic Trip Settings Extra High Interrupting Current Limiting Ampere Low High 2-pole, 600 Vac b 300 A 1500 LC26300( ) LI26300( ) 350 A LC26350( ) LI26350( ) 400 A 2000 LC26400( ) LI26400( ) 450 A 2250 LC26450( ) LI26450( ) 500 A LC26500( ) 861. LI26500( ) 600 A 3000 LC26600( ) LI26600( ) 3-pole, 600 Vac 300 A 1500 LC36300 LI A LC LI A 2000 LC36400 LI A 2250 LC36450 LI A LC LI A 3000 LC36600 LI AL400LA one #1 AWG 600 kcmil or two #1 AWG 250 kcmil AL or Cu AL400LA one #1 AWG 600 kcmil or two #1 AWG 250 kcmil AL or Cu Terminal Wire Range AL600LI5 two #4/0 AWG 500 kcmil AL or Cu AL600LI5 two #4/0 AWG 500 kcmil AL or Cu b 2-pole circuit breaker catalog numbers are completed by adding required phase connection letters as suffix to catalog number. See Digest page -24. c Type LC and LI circuit breakers are NOT recommended for use on single-motor branch circuits. L-frame acccessories starting on Supplemental Digest page 3-24 L-frame dimensions Digest page 7-54 L-frame optional lugs Digest page 7-53 Table.132: Interrupt s (ka) LA LH LC LI 240 V V V Schneider Electric DE2 Discount

29 Breakers L- and PowerPact M-frame for I-Line Panelboards and Switchboards Class 612, 661 Table.133: L-frame 600 A Breakers with Lugs and Factory-Sealed Electronic Trip Units Suitable for Reverse Connectiona Electronic Trip Unit Type Function Trip Unit 600 Vac, 53/60 Hz, 3P Micrologic Standard Micrologic Standard Micrologic Ammeter Micrologic Energy Micrologic Ammeter Micrologic Energy LI 3.3d Sensor b Interrupting (2nd Letter of ) D G J c L c R c 80% 100% 80% 100% 80% 100% 80% 100% 80% 100% Terminal 250 A L( )A36250U31X AL400L61K3e 400 A 600 A LSI 3.3Sd 400 A 600 A LSI 5.3A A A LSI 5.3E A A LSIG 6.3A A A LSIG 6.3E A A L( )A36400U31X L( )A36600U31X AL600LF52K3f 250 A L( )A36250U33X AL400L61K3e L( )A36400U33X L( )A36600U33X L( )A36400U43X L( )A36600U43X L( )A36400U53X L( )A36600U53X L( )A36400U44X L( )A36600U44X L( )A36400U54X L( )A36600U54X AL600LF52K3f a See Supplemental Digest page 3-4 for circuit breakers with field-interchangeable trip units. b For 100% rated circuit breakers (250 A and 400 A only), add a C in the th character place (for example, LRA36400CU31X). c breakers with J, L, and R interrupting ratings are UL certified as current limiting. d 3P circuit breakers with this trip unit can be used for 2P applications. e AL400L61K3 terminal wire ranges are (1) 2 AWG 600 kcmil Cu or (1) 2 AWG 500 kcmil Al. f AL600LFS52K3 terminal wire range is (2) 3/0 500 kcmil. g For applications requiring communications, see Digest page Interrupt s (ka) G J L h 240 V V V i h i L interrupting rating is not available in M-frame. 600 V interrupt ratings not available for D-frame. Table.134: PowerPact M-frame: with ET1.0 Factory sealed trip unit (not field adjustable)800 A j Ampere Adjustable Instantaneous Trip Range k G Interrupting J Interrupting Terminal Low High l l Wire Range 300 A MGA26300( ) MJA26300( ) 2-pole, 600 Vac, 50/60 Hz 3-pole, 600 Vac, 50/60 Hz 350 A MGA26350( ) MJA26350( ) 400 A MGA26400( ) MJA26400( ) A MGA26450( ) MJA26450( ) 500 A MGA26500( ) MJA26500( ) 600 A MGA26600( ) MJA26600( ) 700 A MGA26700( ) MJA26700( ) A MGA26800( ) MJA26800( ) 300 A MGA36300 MJA A MGA36350 MJA A MGA36400 MJA A MGA36450 MJA A MGA36500 MJA A MGA36600 MJA A MGA36700 MJA A MGA36800 MJA /0 through 500 kcmil /0 through 500 kcmil j k l The ET 1.0 trip unit cannot be field replaced, nor does it allow adjustment of the long-time trip point setting. It is considered an electronic equivalent of a thermal-magnet circuit breaker. UL magnetic trip setting tolerances are ±10% from the nominal values shown. Fill in parentheses with the following phase connection options: (2) for AC and (5) for CA. L-frame accessories starting on Supplemental Digest page 3-24 L-frame dimensions starting on Digest page 7-54 L-frame optional lugs digest page 7-53 M-frame accessories starting on Digest page 7-36 M-frame dimensions Digest page 7-55 M-frame optional lugs Digest page 7-3 Table.135: Automatic Molded Case Switches600 Vac, 50/60 Hz Ampere 2-pole 3-pole Withstand m Trip Point Amperes Terminal Wire Range n 240 Vac 480 Vac 600 Vac AC 600 A PJA26000S60( ) PJA36000S /0 through 800 A PJA26000S80( ) PJA36000S kcmil 1000 A PJA26000S10( ) PJA36000S /0 through 1200 A PJA26000S12( ) PJA36000S kcmil m n The withstand rating is the fault current, at rated voltage, that the molded case switch will withstand without damage when protected by a circuit breaker with an equal ampere rating. Fill in parentheses with the following phase connection options: (2) for AC or (5) for CA. Table.136: PowerPact P- and R-frame Interrupt s Voltage P-frame Interrupt R-frame Interrupt G J K L G J K L 240 Vac 65 ka 100 ka 65 ka 125 ka 65 ka 100 ka 65 ka 125 ka 480 Vac 35 ka 65 ka 50 ka 100 ka 35 ka 65 ka 65 ka 100 ka 600 Vac 18 ka 25 ka 50 ka 25 ka 18 ka 25 ka 65 ka 50 ka P- and R-frame accessories starting on Digest page 7-36 P- and R-frame dimensions Digest page 7-55 P- and R-frame optional lugs Digest page Schneider Electric DE2 Discount -2

30 Breakers Micrologic Interchangeable Standard Trip Unit a b c d See Table.136 on Digest page -2 for interrupt ratings. P- and R-frame accessories starting on Digest page 7-36 P- and R-frame dimensions Digest page 7-55 P- and R-frame trip unit options Digest page 7-44 PowerPact P- and R-frame for I-Line Panelboards and Switchboards Class 612 / Refer to 0612CT0101 Table.137: PowerPact P-frame 1200 A (600 Vac, 50/60 Hz) 3P Breaker with Electronic Trip Unit Electronic Trip Unit Sensor Cat. No.ab G Interrupting a J Interrupting a K Interrupting a L Interrupting ac Type Function Code 80% 100% 80% 100% 80% 100% 80% 100% Rated Rated b Rated Rated b Rated Rated b Rated Rated b 600 A P( )A36060 Basic Electronic Trip Unit Fixed long-time, A P( )A36080 (Not Adjustable ET1.0I Interchangeable) Instantaneous 1000 A P( )A A P( )A A P( )A36025(C)U31A 400 A P( )A36040(C)U31A 600 A P( )A36060(C)U31A LI A P( )A36080(C)U31A 1000 A P( )A36100U31A Micrologic Interchangeable Ammeter Trip Unit Micrologic Interchangeable Power Trip Unit Micrologic Interchangeable Harmonic Trip Unit LSI 5.0 LI 3.0A LSI 5.0A LSIG 6.0A LSI 5.0P LSIG 6.0P LSI 5.0H LSIG 6.0H 1200 A P( )A36120U31A 250 A P( )A36025(C)U33A 400 A P( )A36040(C)U33A 600 A P( )A36060(C)U33A 800 A P( )A36080(C)U33A 1000 A P( )A36100U33A 1200 A P( )A36120U33A 250 A P( )A36025(C)U41A 400 A P( )A36040(C)U41A 600 A P( )A36060(C)U41A 800 A P( )A36080(C)U41A 1000 A P( )A36100U41A 1200 A P( )A36120U41A 250 A P( )A36025(C)U43A 400 A P( )A36040(C)U43A 600 A P( )A36060(C)U43A 800 A P( )A36080(C)U43A 1000 A P( )A36100U43A 1200 A P( )A36120U43A 250 A P( )A36025(C)U44A 400 A P( )A36040(C)U44A 600 A P( )A36060(C)U44A 800 A P( )A36080(C)U44A 1000 A P( )A36100U44A 1200 A P( )A36120U44A 250 A P( )A36025(C)U63AE1 400 A P( )A36040(C)U63AE1 600 A P( )A36060(C)U63AE1 800 A P( )A36080(C)U63AE A P( )A36100U63AE A P( )A36120U63AE1 250 A P( )A36025(C)U64AE1 400 A P( )A36040(C)U64AE1 600 A P( )A36060(C)U64AE1 800 A P( )A36080(C)U64AE A P( )A36100U64AE A P( )A36120U64AE1 250 A P( )A36025(C)U73AE1 400 A P( )A36040(C)U73AE1 600 A P( )A36060(C)U73AE1 800 A P( )A36080(C)U73AE A P( )A36100U73AE A P( )A36120U73AE1 250 A P( )A36025(C)U74AE1 400 A P( )A36040(C)U74AE1 600 A P( )A36060(C)U74AE1 800 A P( )A36080(C)U74AE A P( )A36100U74AE A P( )A36120U74AE Table.138: PowerPact R-frame 1200 A (600 Vac, 50/60 Hz) 3P Breaker with Electronic Trip Unit Electronic Trip Unit Sensor Cat. No. G Interruptingac J Interruptingac K Interruptingac L Interruptingacd Type Function Code 80% 100% 80% 100% 80% 100% 80% 100% Rated Rated Rated Rated Rated Rated Rated Rated Basic Electronic Trip Unit (Not Interchangeable) Micrologic Interchangeable Standard Trip Unit Micrologic Interchangeable Ammeter Trip Unit Micrologic Interchangeable Power Trip Unit Micrologic Interchangeable Harmonic Trip Unit Fixed Long-Time, Adjustable Instantaneous ET A R( )A A R( )A36100CU31A LI 3.0 LSI A R( )A36120CU31A 1000 A R( )A36100CU33A 1200 A R( )A36120CU33A LI 3.0A 1000 A R( )A36100CU41A 1200 A R( )A36120CU41A LSI 5.0A 1000 A R( )A36100CU43A 1200 A R( )A36120CU43A LSI 6.0A 1000 A R( )A36100CU44A 1200 A R( )A36120CU44A LSI 5.0P 1000 A R( )A36100CU63AE A R( )A36120CU63AE LSIG 6.0P 1000 A R( )A36100CU64AE A R( )A36120CU64AE LSI 5.0H 1000 A R( )A36100CU73AE A R( )A36120CU73AE LSIG 6.0H 1000 A R( )A36100CU74AE P- and R-frame optional lugs Digest page 7-3 P- and R-frame alternate rating plugs Digest page Terminal Wire Range (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K (3) 3/0 AWG 500 kcmil AL800M23K (4) 3/0 AWG 500 kcmil AL1200P24K Schneider Electric DE2 Discount Terminal Wire Range AL1200R53K (4) 3/0-600 kcmil 1200 A R( )A36120CU74AE1 To complete the catalog number, replace the blank ( ) with the appropriate interrupt rating (G, J, K, or L). For 100% rated circuit breakers add a C in the th character place. For example, the catalog number for a 100% standard-type trip unit with LI trip functions at 250 A would be PGA36025CU31A. The L interrupt rating is supplied in 480 V only. Change the 5 th character (voltage rating) from a 6 (600 V) to a 4 (480 V); for example, PLA34025U31A.

31 I-Line Factory Assembled Panelboards 600 Vac, 250 Vdc Class 2110 / Refer To 2110CT701 Table.13: Base Lugs a Panel Type Lugs 225 A 400 A 600 A 800 A 1200 A HCN HCM HCP-SU HCP HCR-U a When required, add the of a solid neutral from Table.140. Table.141: Base Breaker b Panel Type HCN HCM No. 100 A 150 A Poles FA FH FI c HD c HG c HJ c HL c Breaker Table.140: Standard Solid Neutral Ampere 100/225 A A A A A A 400 A 600 A Panel Type No. Poles LD LG LJ LL LD LG LJ LL JD JG JJ JL KI c LA LH LC c LI c Electronic 100% Electronic 80% LC c LI c MG MJ HCN HCM HCP, HCP-SU A d Panel Type No. Poles PG c PJ c PL c PGC c PJC c PLC c MG MJ PL b Micrologic 80% Micrologic 100% 2 HCN HCM HCP, HCP-SU A cde Panel Type No. Poles PG PJ PL RGC RJC RLC PG PJ PL Micrologic 80% Micrologic 100% HCP, HCP-SU HCR-U b When required, add the of a solid neutral from Table.140. c Standard construction back-fed main. d PG, PJ, PL circuit breakers are available with both thermal-magnetic equivalent and Micrologic trip. The Micrologic circuit breakers are available 80% and 100% rated. The C suffix denotes a 100% rating. e For 1200 A frame thermal magnetic circut breaker with 600 kcmil lugs, select an R-frame Thermal Magnetic circuit breaker in the Product Selector. Table.142: Electronic Trip Units for H-frame Breakers Standard Ammeter Energy LI (3.0) Standard LSI (5.0) LSIG (6.0) f Table.143: Electronic Trip Units for J-frame Breakers Standard Ammeter Energy LI (3.0) Standard LSI (5.0) LSIG (6.0) f Table.144: Electronic Trip Units (L-, P-, and R-frame Breakers) Standard Ammeter Energy Note: Power Harmonic LI (3.0) Standard LSI (5.0) LSIG (6.0) f f When adding G, requires current transformers and a box extension and is available factory assembled only. Note: Energy trip unit available for L-frame circuit breakers only. PowerPact circuit breakers come with a standard LI trip unit. Use the above adder for increase in trip functionality. See Digest page 7-43 for L- frame trip unit descriptions. See Digest page 7-44 for P- and R- frame trip unit descriptions. Table.145: I-Line 200% Rated NeutralStandard Terminal Configuration g Branch Space Neutral Terminals Quantity and Size Type 1 Enclosure Panel Type Ampacity Type H W D In. mm Branch In. mm In. mm In. mm 600 A MLO (8) 750 kcmil A (MG, MJ) M/B (8) 750 kcmil HCM (35) 350 kcmil, A MLO (8) 750 kcmil ()#14-1/0, (17)#14-# A (MG, MJ) M/B (8) 750 kcmil HCR-Uh 1200A M/B, MLO (8) 750 kcmil (8) 600 kcmil, (15) 350 kcmil () #14-1/0, (17)#14-# HCP 600A M/B, MLO (8) 750 kcmil (35) 350 kcmil, ()#14-1/0, (17)#14-# A M/B, MLO 2515 (8) 750 kcmil (35) 350 kcmil, ()#14-1/0, (17)#14-# HCP-SUi 800A M/B, MLO (8) 750 kcmil (8) 750 kcmil, (21) 350 kcmil, () #14-1/0, (17) #14-# g Available in Type 1 enclosure only; for pricing, see Digest page -34. h 6 in. enclosure extension is required for HCRU I-Line panelboard. i in. enclosure extension is required for HCP-SU I-Line panelboard Schneider Electric PE1 Discount -31

32 I-Line Factory Assembled Panelboards 600 Vac, 250 Vdc Class 2110 / Refer to 2110CT701 Table.146: Branch BreakersThermal Magnetic Breakers a (See Digest pages 7-4 through 7-8 for interrupt rating, voltage ratings, Fed. Specs, etc.) Breaker Ampere Breaker 3-pole e 2-pole e 1-pole e 240 V 480 Vac 250 Vdc 600 V Space Only H (In.) 240 Vac 480 Vac 250 Vdc 600 Vac Space Only H (In.) 120 V 277 V Vac 125 Vdc A FA (FY-1P) c A FA b c A FH A A FJd A A FI b A A HD A A A HG A A A HJ A A A HL A A QB A QD b A QG A QJ A JD A A JG A A JJ A A JL A A b KI A b A LA A LH A LC A A b LI A b A MG A A MJ A A PL A PG A PJ /PK A PL A A PLC (100%) e A RG (80%) e A RJ (80%) e RL (80%) e a See Digest pages 7-4 through 7-8 for additional dc ratings. b ac only. c FA, 1P. d 480Y/277 Volt rated circuit breakerdo not use on 480 Volt 3Ø3W Delta systems. e See Table.144 on Digest page -31 for P- and R frame Micrologic trip unit price adders. Space Only H (In.) Schneider Electric PE1 Discount

33 I-Line Factory Assembled Panelboards 600 Vac, 250 Vdc Class 2110 / Refer to 2110CT701 Table.147: Branch BreakersElectronic Trip Breakers a (See Digest pages 7-4 through 7-8 for interrupt rating, voltage ratings, Fed. Specs, etc.) Breaker Ampere Breaker 240 V 480 Vac 250 Vdc 3-poled 2-pole d 1-pole d 600 V Space Only H 240 Vac 480 Vac 250 Vdc 600 Vac Space Only H 120 V 277 V 277 Vac 125 Vdc A A HD (80%) b A A JD (80%) c A A HG (80%) b A A JG (80%) c A A HJ (80%) b A A JJ (80%) c A A HL (80%) b A A JL (80%) c A A LD (80%) d A A A LG (80%) d A A A LJ (80%) d A A A LL (80%) d A A LDC (100%) d A A LLC (100%) d A A LGC (100%) d A A LJC (100%) d A A DG (100%) e A DG (80%) e A DJ (100%) e A DJ (80%) e A DL (100%) e A DL (80%) e A A PG (80%) d A A A A PJ/PK (80%) d A A A A PL (80%) d A A A A PGC (100%) d A A A PJC/PKC (100%) d A A A PLC (100%)d A RG (100%) d A RJ (100%) d RL (100%) d a See Digest pages 7-4 through 7-8 for additional dc ratings. b See Table.142 on Digest page -31 for H-frame electronic trip unit price adders. c See Table.143 on Digest page -31 for J-frame electronic trip unit price adders. d See Table.144 on Digest page -31 for L-, P-, and R-frame electronic trip unit price adders. e See the Supplemental Digest for D-frame electronic trip unit price adders. Space Only H 2012 Schneider Electric PE1 Discount -33

34 I-Line Factory Assembled Panelboards Table.148: QO Plug-On Branch Breakers Transition Charge per 6 QO one-pole spaces (H=4.5 in. per 6 one-pole spaces) 328. QO Branch circuit breakers See Digest page 7-10 Table.14: Sub-feed/Feed-through Lugs a Ampere 225 A A A A A 180. a 2 or 3-pole Branch Mounted; SL Kit used for both SFL and TFL. Table.150: Ground Bars Equipment Ground Bar 180. Copper Ground Bar b 148. Insulated/Isolated Ground Bar Additional Neutral Assembly b Add to equipment ground bar. Table.151: Name Plates Standard white face/black letter laminated bakelite, 1 in. x 3.5 in., adhesive backed or screw mountable with screws in a bag assembly ( includes engraving) Table.152: Copper Bus Bars Ampere Type 225 A HCN, HCM A HCN, HCM, HCP A HCN A HCM, HCP, HCR-U A HCP, HCR-U Table.153: Neutrals Ampere Type Adder A Copper Neutral A Copper Neutral A Copper Neutral A Copper Neutral Table.154: 200% Rated Neutrals Ampere Type Adder 225 A Aluminum A Aluminum A Aluminum A Aluminum A Aluminum A Copper A Copper A Copper A Copper A Copper 200. Table.155: Metal Directory Frame Metal Directory Frame Adder Frame attached to trim (not available on four piece trim) Common Feature Pricing Class 2110 / Refer to 2110CT701 Surgelogic SPD Surgelogic SPD unit in I-Line plug-on construction: An integrally mounted surge protection solution that mounts on to an I-Line Panelboard bus stack just like a J-Frame circuit breaker. Requires 13.5 in. of mounting height. Available as factory assembled and merchandised. For SPD unit pricing and information, see Digest pages 6-3 and Table.156: Door-in-Door Trim Door-in-Door Trim Adder Trim has piano hinge down one side. Door opens by single latch; Entire trim opens by removing screws Hinged Door-in-Door with Outer Door Lock Added 836. Table.157: Weatherproof or Dusttight CabinetsType 3R, 5, 12 Weatherproof or Dusttight Cabinets Adder Maximum 26 in. wide box Maximum 28 in. wide box Maximum 32 in. wide box Maximum 42 in. wide box Maximum 44 in. wide box Table.158: Copper Mechanical Lugs Lug Interiors Ampere Breaker Interiors per Pole 100/125 A A A A A A Table.15: Copper Compression Lugs Ampere Lug Interiors Breaker Interiors per Pole 100/125 A A A A A A 836. Table.160: Aluminum Compression Lugs VCEL Ampere Lug Interiors Breaker Interiors c Per Pole 100 A A N/A A A A A A Note: Additional factory modifications. See Digest page -38. c Compression lugs are not available on LC, LI, LE, LX, and LXI circuit breakers. I-Line Plug-On Unit with Surgelogic SPD Table.161: Surgelogic SPD Options Surgelogic SPD Options Dry Contacts Standard Remote Monitor Note: Requires HCM interior minimum. Table.162: Surgelogic Branch Mounted I-Line SPDModel IMA Surge Current ka Voltage 100 ka 120 ka 160 ka 200 ka 240 ka HL FI HL FI HL FI HL FI HL FI 120/240 1P3W Y/120 3P4W /120 3P4W Y/277 3P4W Y/347 3P4W Schneider Electric PE1 Discount