A TechForAg 'Ready-To-Milk' Modular Parlor. Model: Dbl. 4 Original Germania ProTime II HerringBone

Transcription

1 A TechForAg 'ReadyToMilk' Modular Parlor Model: Dbl. 4 Original Germania ProTime II HerringBone Key Features: Conventional Exit Automatic Indexing AllStainless 45" CowtoCow Distance Parlor will be 53" wide (4" wider than the original Germania) to accommodate 1,800 +lbs cows This parlor should milk from 25 to 40 cows per hour with one milker Prepared For: Website # 136 Preliminary Proposal # AllStainless Dbl. 8 ProTime II with Legacy 9,000 Arm TakeOffs installed at Bruce Siltberg's Dairy near Dresser, WI June 2010 Page 1 of 25

2 Qty Units Description Cost to Enduser 8 Stalls Germania Pro Time II RumpRails 48" AllStainless Remanufactured $ 2,857 4 Entrance & Exit Gates 2 1/2 x 2 1/2 x 11ga stainless tubing $ 2,857 8 Stalls 5" x 15" Overhead Channel Stainless $ 743 Note Parlor from Texas Page 2 of 25

3 2 Units Conventional Exit Brisket Bars Remanufactured AllStainless RapidExitReady Brisket Bars Designed for Automatic Indexing $ 3,314 0 Groups RapidExit Lift Group With: 4" x 42" lift cylinder (2) stainless cables (2) stainless cable retainers and (3) new pulleys $ 0 Groups Rapid Exit Control Panel $ 4 Units Stainless Brisket Bar Posts with Swing Arms $ 4,857 (Cow Platforms to be 53" wide with 10" Indexing System for 1,800+ lbs cows) Page 3 of 25

4 2 Groups SemiAutomated Cow Traffic Controls New! (1) 3" x 10" stainless Entrance Gate Cylinders (Exit Gates are manually operated) (2) 3" x 10" stainless Cylinders for Auto Indexing (2) 4Button Cow Traffic Control Station $ 5,510 Cow Traffic Controls at last stall on either side of parlor. Stainless cylinders operate Entrance & Exit Gate Page 4 of 25

5 0 Stalls 8 Stalls AllStainless Gutter and Curbing New! Allinone welded unit Note Grates will be Original Germania galvanized! $ Stainless Gutter, Curbing and Grates are all one welded unit. For utmost Cow Comfort we chose 3/4" x 3/4" bars, the widest in the industry, bar none. Instead, Galvanized Grates with only 1/4" wide bars are industry standard, as are concrete Gutters formed by the local Contractor (and for which you pay extra) Stainless Curbing only no Gutter no Grates New! Allinone welded structure, part of Module Base $ 2,206 Page 5 of 25

6 Original Germania Heavy Duty AllAir Operated Crowd Gate 0 28 ft x 90 ft Starts automatically with 'Brisket Bar Up' stops after 50 sec Stops automatically at top and bottom of Holding Pen 7" instead of 6" diam. wheels $ 0 ft C4 x 6.5 lbs Crowd Gate Channel New! Welds very straight over 6 ft Span/Distance between Vertical Posts Does not require any other reenforcement or support; cold galvanized $ Heavy Duty, GermaniaStyle Crowd Gate; AirPowered Gear Motor no electric controls whatsoever. Lifts anywhere in Holding Pen and returns overhead cows to rear of pen. Air Motor shuts off automatically, both in front and back. Page 6 of 25

7 0 ft 0 ft Holding Pen Fence, galvanized with 3" 5 ft on center per 20 ft section of fence; (4) 1 1/2" Pipe 12" o/c Normally, your Contractor provides the Holding Pen Fences. We'll provide them if he doesn't want to or $74/ft les $ 2 x 10 ft VLane Fences from H.P. into $74/ft less 15% $ Three Crowd Gate Control Stations: Cost include with Crowd Gate Left: Main Control station in back of parlor; Center: Remote Controls in back of Holding Pen Right: Two extra buttons in front of parlor to Page 7 of 25 reduce walking

8 0 Units Original Germania Legacy 9000 AllStainless Arm TakeOffs Remanufactured Remanufactured but with high percentage of new parts AllAir controlled, Allstainless construction with springloaded clutch assembly for the Arm $ Page 8 of 25

9 Germania Top Outlet Claw Remanufactured 8 Units Air Forks 06 Shells 60" Milk Hose Silicone 108" Pulsation Hose Short air tubes Liners of your choice: Brand & Model BouMaticstyle Pulsators All Rubber Goods are new! $ 3,249 Germania's Top Outlet Claw hangs well balanced on the arm for milking and equally so in the rest position. At Germania we developed this claw in 1978, the original TopOutlet Claw, and have made it in its original form ever since. New in 2010 AllSilicone Rubber. except inflations Page 9 of 25

10 8 Stalls 2 Units Pulsation System New! 3" PVC Pulsation line with hoses, fittings & wiring harness 3" PVC FreshAir line with fittings & hoses (4) FreshAir Filters (2) 3" PVC CrossOvers in front & back $ 971 (Pulsators included with ClawClusters) 16Unit Strangko Pulsation Controllers (one of which will be new) Electrician provides 120 volt receptacle nearby bid separately! $ 1,857 2nd Controller serves as Standby prewired for instant changeover. No tools required. Page 10 of 25

11 0 Stall Equiv. 0 Unit HERITAGE CIPReceiver Combination Group New! This group combines the (2) traditional Receiver Groups and the CIP System into a single preassembled aggregate preplumbed, prewired and palletized $ 26" diam. x 24/34" Receiver which is also the Wash Vat for the CIP Cycle (Nominal Capacity of 80 gl. Dbl. 12 estimated to use 60 gl/cycle, 180 gl total) AWstyle Moisture Trap with 3" Vac inlet & 3" Ubend, Slide Valve, SST Gauge ' (1) 4" x 33" Sock Milk Filters with 2" side outlet, installed at 45 dgr angle 1 1/2 hp Milk Pump with Variable Speed Drive (2) LLC Probes (Floatstyle) for milk and water levels 1 1/4" Input Group with hot and cold water valves + (3) chemical inputs Water supply lines to this group needs to be at least 1 1/4" diameter. Otherwise takes too long to fill Receiver 2" Ball Check Valve at pump with air blowout of Rest Milk ' HERITAGE Model 12.5 Pipe Line Washer (3) peristaltic chemical pumps deliver detergent, acid and sanitizer automatically All MAC Interface Valves and Relays Electrician supplies: 220 or 430 volt three phase to this Group Plumber s upplies: Hot & Cold water to the input group and Water to the Plate Cooler Group includes an extra 1 1/2 hp Milk Pump, prewired with watertight twist lock plugs for instant changeover, no tools required Group also includes a standby Frequency Controller similarly prewired with shielded cable 4,500 lbs/hr Dual Pass Plate Cooler (2" inlet and outlet, must handle 130 gl of CIP Solution) $ Page 11 of 25

12 HERITAGE CIPReceiver Combination Groups The new HERITAGE CIP Receiver Combination Group installed at the Steve Paul Dairy, Whitewater, WIS, April 2010 This Group replaces the existing (2) Receiver Groups and the CIP System But need to discuss where this group might be located Page 12 of 25

13 1 Group Conventional Receiver Group Remanufactured $ 5,794 1 Group Germania CIP System Remanufactured Including: 40 Gl vertical Wash Sink 1.5 hp Pressure Pump One Air Injector 3/4" Hot and Cold Water Input Group (3) Peristaltic Pumps for chemicals (3) 1 1/2" Drains $ 5,714 1 CIP System will be controlled by a new HERITAGE Pipe Line Washer $ 3,500 Page 13 of 25

14 0 Units FoldUp CIP Cup Holders Do not need Rubber Cups (To be discussed ) $ 8 Units Traditional CIP Cup Holders $ Units AirPowered CIP Cup Holders Just push a button Now you see them then you don't; all 32 at once $ Page 14 of 25

15 3" LoLine 8 Stalls Single Loop, double slope line $ 1,429 2" CIP Lines 8 Stalls From the Wash Sink to the back of the Parlor $ 1, /2" Discharge line 50 ft from the Receiver Group to Milk Tank. Includes special adapters at Tank and Safety Switches. $ 2,571 0 Units PipeLine patches to close inlet holes both of the 3" LoLine and the 2" CIP Line (15 out of 48) $ 0 Units 3/4" Pipeline Inlets for both 3" and 2" Lines $ Page 15 of 25

16 1 Group 1 Group Compressed Air System New! (1) 5 hp SpeedAir Compressor with Refrigerant Drier $ 7,143 Electrician provides 230 Volt 3phase to this group Picture shows (2) compressors, quote is for (1); Pictures show Twin Tower Drier (needed for Crowd Gates in very cold climates); Quoted Refrigerant Drier Small Air Prep Group APPS New! Page 16 of 25 Includes 1/2" copper lines & fittings to all stations of parlor $ 564

17 1 Units 60 ft 7.5 Hp Vacuum System with LobeStyle Pump Remanufactured GardnerDenver/SutorBuilt Pump $ 3,571 6" PVC Header Lines with 3" fittings to Pulsation and 4" adaptors to the CIP / Receiver Group $ 1,714 Electrician provides 430 volt 3 phase to this Group 6" Header Line supplies CIP Receiver Group and Pulsation System Page 17 of 25

18 1 Group OnFarm Spare Parts Kit (Contains only new parts) Includes all essential parts for at least (1) year of operation (2) sensors, a retract cylinder, at least (1) of each air valves, etc. $ 2,857 2 x 5ft Stainless Curb Extensions in Front 11 ft from Exit Gate to Breezeway Wall. Prevents manure from running into the pit; Includes concrete guard. $ Pcs Double Compartment Sink New! $ 643 Accessories Group New! 1 Group Hand Wash Sink, Filter Sock Holder with (1) box of Filters, SST paper towel holder, Soap Dispenser, Hose Rack for garden hose in Milk House, etc. $ 679 Pit Mats for 8 ft wide x 60 ft long pit floor (MatTec Mats) 0 squ ft Page 18 of 25 Color of your choice Blue, Green, Red or White $

19 1 Unit Stainless Pit Steps 4 steps, 30" wide New! $ 857 (1) 20 ft 1" WashDown Hose for Cow Platforms 20 ft with solid Brass Firehose Nozzles $ ft (1) x 12 ft 3/4" Cleanup hoses for the pit $ 69 Page 19 of 25

20 0 Unit Stainless Breezeway Fence New! with (2) 3ft 'Side Wings' Made from 2.5" x 2.5" square stainless tubing 10 ft + 3 ft long, with (2) Horizontals and (4) 3 ft Verticals $ Page 20 of 25

21 4 Stall Stainless Modular Platforms New! 2 Units The structural bases of the Modules; Height of your concrete cow platform should be 34" if you are comfortable with a 38" working height. To be discussed! $ 1,714 We build our parlor modules on platforms, a frame work made form 2" x 4" steel tubing and usually 53" wide x 50.6 ft long for the typical dbl. 12. Normally, we slide the Modules into place on this steel frame work, pushed by a Skid Loader. Parlors up to dbl. 12 come on two trucks, all larger ones need four. Page 21 of 25

22 Summary Page SubTotal Materials $ 69,285 Less: 15% DairyDirect Discount $ (10,393) Parlor Materials after Discount $ 58,892 PreInstallation Labor and Supplies provided by TechForAg at it's factory to convert the above materials into a ReadyToMilk Modular Parlor (calculated at 18% of materials) $ 12,471 1 Truck Freight $ 400 OnSite Installation Labor, Supplies & Expenses (One Installers for 5 days plus one Parlor Specialist for two days followup and Startup of milking) $ 4,620 Grand Total Parlor with Freight & Installation $ 76,383 Less: 'Low Milk Price' discount of 9% $ (6,874) Grand Total after 2nd discount $ 69,509 Per Stall $ 8,689 Page 22 of 25

23 8 Stalls Optionally Available 1" Kraiburn Rubber Mats (Made in Germany) New! For the (2) Modular Cow Platforms $ 1,260 Plus Freight and Installation Page 23 of 25

24 0 Stalls Germania Back Flush System, incl.. Stainless Turn Valves (2) 14 gl.vacuum Sweep Tanks with (2) twoway Valves each (2) Power Manifolds with (2) twoway Valves each (2) Control Boxes, one per side (1) AllStainless Iodine Injection Group with B13 LiquiMatic Pump $ (4) MilkSweep Relays 1 1/2" stainless BF lines below curb Plumber supplies Cold water to the Iodine Injection Group. The PVC lines from the Iodine Injection Group to the (6) 2way valves of the (2) Power Manifolds Bid separately! Includes Freight and Installation Page 24 of 25

25 Terms I If production at TFA starts several months in the future 1) 15% down at signing of contract 2) 35% on start of production 3) 45% on delivery of parlor to the dairy 4) 5% on Startup of Milking 4) $1,000 Rebate for prompt payment Terms II If production at TFA starts more or less immdiately 1) 35% at signing of contract, plus 2) 25% six weeks later 2) 35% on delievery of parlor to the dairy 3) 5% on startup of milking 4) $1,000 Rebate for prompt payment Page 25 of 25