Linear Alignment Coupler. Flange Couplers and Weld Plates. Spherical Rod Accessories. Milwaukee Cylinder provides various cylinder accessories to

Transcription

1 ylinder ccessories Page Linear lignment oupler MLOK Rod lamp Flange ouplers and Weld Plates Spherical Rod ccessories Milwaukee ylinder provides various cylinder accessories to maximize your cylinder s potential. Linear lignment ouplers prevent binding and erratic movement caused by misalignment. mlok Rod lamps hold position securely after motion has stopped. dditional accessories are detailed in this section, and also on the inside back cover of this catalog. 18

2 Dimensional Data Linear lignment oupler F B Deep G D H Linear lignment oupler Dimensional hart Model No. M-1 M-75 M-7 M-500 M-65 M- M-875 M- M-150 M- M-1 M-1875 M-000 5/16- ⅜ B Body Ø 1 1 ¼ ¼ Body Length ⅜ ⅜ D Shank Length ¼ ¼ Length 1⅛ 1⅛ 1 1 ¼ ¼ F Shank Ø ⅓ ⅓ 1⅜ 1⅜ 1 1 NOTS: ll dimensions are subject to change by manufacturer. Larger sizes, special designs and metric versions are available. onsult factory. Use jam nut to lock coupler to rod when used with full diameter threads. Use "Max. Rated Load" for :1 safety factor. G Flats ¼ H Flats ¼ ¼ Max. Rated Load (lbs) ,000 19,500,500,500 60,000 60,000 Max. Yield (lbs) ,000 1,000 19,000,000 9,000 6,000 78,000 1,000 1,000 0,000 0,000 liminate lignment Problems. Install a Linear lignment oupler. Features Reduces rod seal and bearing wear Prevents binding and erratic movement caused by misalignment Permits a greater tolerance between cylinder centerline and mating member Works equally well in push or pull applications Spherical Movement L 1/16 Radial Float yl ccessories Manipulators Power Units/Valves Design Guide 19

3 MLOK Rod lamp Series H ontact your Milwaukee ylinder representative for product selection assistance. Series LH Series MH Series Series MN MLOK TYP RH ROD LMP Provides power-off clamping of rods and shafts lamps are actuated by a spring/collet mechanism and unclamped by hydraulic pressure Designed to clamp components after the motion has stopped and to hold the position securely as long as the forces do not exceed the table values Hyd-Pneu Devices HOW MLOK TYP RH ROD LMP WORKS Optional ccessories yl ccessories LMPD Hydraulic pressure off Zero back pressure UNLMPD Hydraulic pressure at minimum Release pressure not to exceed 000 psi Proximity Switch to indicate an unlocked condition. ir Bleed - It is important that all the air be bled from the MLOK piston area. It is recommended to install an automatic air bleed valve between the MLOK and the oil reservoir. HOW TO ORDR xample: RH - XXX XXX X 100 Rod Size - X.XX (inches) 150 ylinder Bore Size - X.XX (inches) Release Pressure - (psi divided by 10) Select Options: P - Proximity Switch (indicates unclamped postion) N - No Proximity Switch xample: RH N 1.00" Rod -.50" ylinder Bore psi Release Pressure No Proximity Switch Movement in Load directionis zero. Movement in Load B direction is.01" maximum when clamp is fully locked 150

4 Dimensional Data MLOK Rod lamp Rod Dia. 1 Rod Dia. Tolerance yl Bore MLOK Part No. RH MIn. Release Pressure psi Max. Holding Force D L R ±.005 TF ±.005 FB B K F G J M Port S S S S S S S S S S S Other sizes available upon request Rod tolerances that exceed these limits will affect the holding force. Maximum Hydraulic Release Pressure: 000 psi Holding forces are based on dry or mineral-oil lubricated shafts. Dimensions are subject to change without notice S S S S S S S 10 yl ccessories Manipulators Power Units/Valves Design Guide 151

5 Flange ouplers & Weld Plates Dimensional Data FLNG OUPLRS Series H Series MH Hyd-Pneu Devices Series MN Series Series LH PRT# ROD DI. B D H I J L M N P MTRIL F ISI 11 D F ISI 11 D F ISI 1018 D F ISI 1018 D F ISI 1018 D F ISI 1018 D F ISI 1018 D F MOD F MOD F MOD F MOD F MOD WLD PLTS yl ccessories PRT# SIZ F G H I K L M MTRIL WP D 1018 WP / D 1018 WP / D 1018 WP / D 1018 WP / D 1018 WP / D 1018 WP / D 1018 WP / HRS WP / HRS WP / HRS WP / HRS WP / HRS 15

6 Dimensional Data Spherical Rod ccessories SPHRIL Y BRKTS PRT# B D DD F FL LR M MR R B / /8 11/8 11/16 11/ B / 5/8 17/8 1/16 1/16.56 B / ¼ 1 1/8 1/8.5 B-1 1/8 1. 1/ 5 ⅛.81 B-17 11/ 1.0 9/ 6 ⅛ ¼ 1/8 1/8.9 B / 7 1 /8 / MTRIL: 05 thru 10, 11 Steel Forging; 1 thru 0, Steel Weldment PIVOT PINS FOR SPHRIL LVIS BRKTS SPHRIL ROD YS PRT# D L PRT# D X R L KK JL PP /16 R /16 7/8 7/16 7/8 7/16 0 PP / R / 11/ /16 PP R /8 1⅜ 17/ PP /16 R /8 1 /16 11/16 17/8 1 PP / R /8 117/ /16 ⅛ 1 1 ¼ PP /16 R /8 / MTRIL: D11 HT TRTMNT: Nitrotec MTRIL: Ductile Iron asting SPHRIL LVIS BRKTS PRT# F M R D F W DD FL LR MR B B B B B B MTRIL: Steel Weldment yl ccessories Manipulators Power Units/Valves Design Guide 15