1. Selection Guide Page Volume Page Chemical Resistance Page Thermal Resistance Page Transparency Page 3

Transcription

1

2 Contents 1. Selection Guide Page Page Chemical Resistance Page Thermal Resistance Page Transparency Page 3 2. Description Page s for Tubes and Sealing Caps Page Sterilization Page Chemical Resistance Page Nomograph Relative Centrifugal Force Page 8 3. Ordering Information and Prices Page Glass Tubes Page Plastic Tubes Page Advanced Oak Ridge Tubes Page Bottles Page Tubes and Bottle for Ultra Centrifuges Page Other Accessories Page Compatibility with Rotors of other Manufacturers Page List (sorted by Catalog No.) Page 31 Many factors influence the performance characteristics and lifespan of centrifuge consumables. This catalog has been compiled as a general guideline but, in no case, expresses absolute guarantee of the products under laboratory conditions. Due to the large number of different applications and techniques the single perfect material for centrifuge tubes does not exist. A material may show excellent performance qualities in one application and then fail horribly in the next. Note: All centrifuge tubes should be tested prior to use. At the first sign of irregularities these tubes should be discarded or the maximum speed should be lowered drastically. List of used trademarks: AOR Advanced Oak Ridge Tubes (Utility patent of Herolab GmbH Laborgeraete) Borex and Polyflor are registered trademarks of Herolab GmbH Laborgeraete, Wiesloch, Germany. Delrin is a registered trademark of DuPont, Delaware, U.S. Duran is a registered trademark of Schott, Mainz, Germany. page 2 of 35

3 1. Selection Guide 1.1. The volume of the tubes is determined by the size of the sample material, the rotor bores and the necessary adapters Chemical Resistance Chemical Groups B, D PA PPCO PP PE PC PF PS Acids, dilute S S S S S S S S Acids, strong S S S S S U S M Alcohols and bases S S S S S U S S Aldehydes and oxidizing agents S M M M M M S U Esters S M M M M U S U Hydrocarbons Aliphatic (i.e. hexane) Hydrocarbons halogenated or aromatic (i.e. phenol, chloroform) S M M S U U S U S M M M M U S U Ketones (i.e. acetone) S M M M M U S U Salts S S S S S M S M 1.3. Thermal Resistance Temperature Range B, D PA PPCO PP PE PC PF PS < +4 C U S S U S S S U +4 C to +20 C S S S M S S S S +20 C to +40 C S M S S S S S S Autoclavable S S S S U S S U Note: For continuous low temperature applications PPCO resp. PA is the material of choice Transparency Transparency Range B, D PA PPCO PP PE PC PF PS Transparent x x x Translucent x x x x Opaque x S Satisfactory B Borex Glass PPCO Polypropylene Copolymer PC Polycarbonate M Marginal, test runs recommended D Duran Glass PP Polypropylene PF Polyflor U Unsuitable, not recommended PA Polyallomer PE Polyethylene PS Polystyrene page 3 of 35

4 2. Description GmbH 2.1. s for Tubes and Sealing Caps Tubes and capping systems can only function at optimal performance levels if the rotor and centrifuge are kept in the best possible condition. The condition of your rotors is critical to ensure the correct functioning of the tube and capping system. Follow the instructions in your rotor manual and clean your rotors carefully after each run to prevent the start of corrosion and rotor degradation. Glass Borex = B / Duran = D / HS = High-Speed Temperature range: B = 0 to C / D = 0 to C / HS = 0 to C Transparent glass tubes are available in Borex and Duran for low speed applications when clarity and good chemical tolerance is required. Glass tubes must be treated with care when removing pellets, washing and storing. Surface scratches and etchings will significantly reduce the life span of glass tubes. All glass tubes show a better tolerance to high temperatures than to low temperatures. However, strong acids and bases may attack the glass surface at elevated temperatures. Hydrofluoric acid attacks glass already at room temperature. High-Speed glass can be spun at higher g-forces than the other two glass materials. Polyallomer PA or Polypropylene Copolymer PPCO Temperature range: - 40 to C Polyallomer is a copolymer of polypropylene and polyethylene resulting in a material with the best features of each component. It is a translucent material which attains additional "contact" clarity when filled with liquid allowing easy viewing of pellets, liquid levels and interfaces. PA is the most versatile of all tube materials and is the best choice if uncertain about the particular effects of an application on a polymer. Polyallomer is the material of choice for continuous low temperature centrifugation applications. Polypropylene PP Temperature range: to C Polypropylene is a translucent material with good chemical and temperature resistance. It may become brittle when exposed to low temperatures; therefore, centrifugation at temperatures below 4 C should be avoided. It is important to equilibrate cold tubes to the temperature of the run before centrifuging, particularly if experimental protocols call for repeated spins and temperature adjustments. Polypropylene is only translucent, but liquid levels, sharp interfaces and pellets can be easily viewed. Polyethylene PE Temperature range: to + 90 C Polyethylene is the material of choice for techniques involving acetone, acetic or hydrochloric acid. It is an opaque polymer which makes the viewing of tube contents slightly difficult; however its increased flexibility, compared to other polymers, makes it an excellent tube for slicing, piercing or low temperature applications. Polyethylene tubes need to be completely filled and capped to run at maximum speeds. Polyethylene is sensitive to high temperatures and cannot be autoclaved. page 4 of 35

5 2. Description GmbH Polycarbonate PC Temperature range: to C Polycarbonate is a transparent, rigid and non-pierceable material. It is compatible with neutral salt and dilute acid solutions but extremely sensitive to organic solvents, alcohols, oils, DMSO and alkaline solutions. Tubes and bottles are reusable, but care should be taken to avoid scratching the surface with glass rods and hard bristle brushes. Please use rubber coated spatulas and soft bristle brushes. Important note for cleaning: Use only mild, non-alkaline detergents and wash them by hand. Repeated washing in machines or the use of alkaline detergents will damage the material. Polyflor PF Temperature range: to C Polyflor is a translucent material with excellent chemical resistance to acids, bases, salts and organic solvents at temperatures encountered during centrifugation. Some organic solvents will attack the fluorocarbon but only at elevated temperatures above 50 C. This Teflon-like polymer has excellent temperature resistance and is a good choice for low temperature applications. The material is slightly flexible and tubes need to be completely filled and capped to run at the maximum listed speeds. Polystyrene PS Temperature range: - 10 to + 75 C Polystyrene is a transparent rigid material compatible with most aqueous based solutions but not with most organic solvents. This material has limited temperature resistance and cannot be autoclaved. Tubes will break if dropped or subjected to high stress conditions (temperature extremes or high g- forces). All polystyrene tubes are thickwall and should be used only once, then discarded. The primary uses of polystyrene tubes are low speed applications, i.e. pelleting, when clarity is essential Sterilization Sterilization B, D, HS PA PPCO PP PE PC PF PS Autoclave x x x x x x Dry Heat x x Gas x x x x x x x x Chemical x x x x x x x x UV Light x x x Tubes or bottles made of PA, PC, PF, PPCO and PP can be autoclaved repeatedly under the normal condition of at least 15 minutes at 121 C and 103 kpa (1,03 bar = 15 psi). The sterilization time for PC should not exceed 20 minutes at 121 C, as repeated sterilization reduces the mechanical rigidity of PC but also of all other plastic materials as well. Pathogenic prions (Creutzfeld-Jakob disease, (vcjd)) can be destroyed only through sterilization at 134 C with duration of 18 minutes. For this application we, Herolab, can offer a special polypropylene (PPCO) on request. General guidelines for autoclaving: All products must be thoroughly rinsed with distilled water before being autoclaved, since residues of cleansing agents can cause cracks, discolorations and stains. Closures of tubes or bottles need to be removed completely before autoclaving in order to prevent damages during the cooling-down process. Tubes and bottles that had been autoclaved previously must be checked for signs of deformation or cracks before using them again. page 5 of 35

6 2. Description GmbH 2.3. Chemical Resistance PA PPCO PC PE PF PP PS PA PPCO PC PE PF PP PS acetaldehyde M U M M M U deoxycholate S S S - S - acetic acid (5%) S S S S S 1 U dextran (dextran sulfate) S S S S S - acetic acid (60%) S U S S M S diacetone S - S S S M acetic acid (glacial) S U M S U U diethylether M U U S M U acetone S U S M S U diethyl ketone U U M - M U Alconox S M S - S - diethylpyrocarbonate S U S - S U allyl alcohol S S S - S M N,N-dimethylformamide S U S U S U aluminium chloride S S S S S M dimethylsulfoxide S U U - S U aluminium fluoride S U S S S M dioxane M U S M M S ammonia S U U S S S ethanol (5%) S U S S S S ammonium acetate S S S - S S ethanol (50%) S U S S S S ammonium carbonate S U S S S - ethanol (70%) S U S S S S ammonium hydroxide (10%) S 1 U S S S 1 S ethanol (95%) S U M S S U ammonium hydroxide (28%) S 1 U S S S 1 M ethyl acetate M U U S U U ammonium hydroxide (cone.) S 1 U S S S 1 M ethylene dichloride U U U S U U ammonium phosphate S S S S S - ethylene glycol S U S S S S ammonium sulfate S S S S S - ethylene oxide S M S S S U ammonium sulphide S U - S S S ethylene M U U - M - amyl alcohol M S S S M S fatty acids, saturated S S U S S S aniline (benzenamine) U U U S M U fatty acids, unsaturated S S U S S S Aqua Regia U U U - U M ferric chloride S S S barium salts S S S S S - Ficoll-Paque S S S - S - benzene U U U S U U fluoroboric acid S - S - S - benzyl alcohol U U U S U U formaldehyde (5%) S S S S S S boric acid S S S S S S formaldehyde (40%) S S S S S S n-butyl alcohol S M M S S S formic acid (3%) S U S - S S calcium chloride S M S S S 1 - formic acid (10%) S U S - S S calcium hydrochloride S M S S S M gallic acid S - S S S - carbon tetrachloride U U U - U U glycerol S S S S S S cesium acetate S S S - S - guanidine hydrochloride S U S - S - cesium bromide S S S S S - guanidine isothiocyanate S U cesium chloride S S S S S - Haemo-Sol S S S - S - cesium formate S S S - S - 2-heptyl S - S S S - cesium iodide S S S - S - hexane M U U S S U cesium sulfate S S S S S - hydrochloric acid (5%) S S S S S S cesium trifluoracetate S S S - S - hydrochloric acid (10%) S U S S S S chlorine water S S M S S M hydrochloric acid (37%) M U S S M S chlorobenzene U U U S U U hydrochloric acid (50%) M U S S M S chloroform M U M S M U hydrochloric acid (cone.) M U - S S S chromic acid (10%) S M U S S M hydrofluoric acid (10%) S M S S S S chromic acid (50%) S 1 U U S S M hydrofluoric acid (50%) S U S S S S citric acid (10%) S S S S S S hydrofluoric acid (100%) S U S S S - cresol M U U - U M hydroformic acid (100%) S - S - S - cyclohexane U U U S U U hydrogen peroxide (3%) S S S 1 S S S cyclohexanol S M S S S S hydrogen peroxide (100%) S S S 1 S S M 2. Description Note: This chart has been consolidated from a number of sources. Chemical resistance data is included only as a guide to the selection of tube materials. No organized chemical resistance data exist for materials under the stress of centrifugation. The recommendation is to test sample lots prior to use. page 6 of 35

7 PA PPCO PC PE PF PP PS PA PPCO PC PE PF PP PS isbutanol S S S - S M potassium hydroxide (45%) S U S S U M isopropanol S U S - S M potassium hydroxide (cone.) S U S S U M kerosene U U U S U U potassium permanganate S S S S S - lactic acid (20%) S S M S S S 2-propanol S U S S S S lactic acid (50%) S S M S S S pyridine (50%) M U U M S U lactic acid (100%) S S M S S S rubidium bromide S S S - S - lauryl alcohol S - S - S - rubidium chloride S S S - S - lead acetate S - S S S - silver cyanide S - S S S - magnesium chloride S S S S S - silver nitrate S S S S S M magnesium hydroxide S U S S S - sodium bisulphate S S S S S - maleic acid S S S S sodium borate S S S - S - manganese salts S - S - S - sodium bromide S S S S S - mercaptoacetic acid S U U - U - sodium carbonate S U S S S - 2-mercaptoethanol S U - - S - sodium chloride (10%) S S S S S S methanol S U S S S 1 S sodium chloride, saturated S S S S S - methyl ethyl ketone S U U M S U sodium dichromate S - S - S - methylene chloride U U U S U U sodium dodecyl sulfate S S S S S - metrizamide S S S - S - sodium hydroxide (1%) S U S - S S nickel salts S S S S S - sodium hydroxide (10%) S U S - S S nitric acid (10%) S 1 S S S S S sodium hydroxide (cone.) M U S - M S nitric acid (30%) S 1 M U S M S sodium hypochlorite S 1 S U S U - nitric acid (50%) S 1 M U S M M sodium iodide S S S - S - nitric acid (95%) M U U S M M sodium nitrate S U S S S - oils (petroleum) S U U S U S sodium peroxide S - S S S - oils (other) S U U S S S sodium sulfate S S S S S - oleic acid S S S - S - sodium sulfite S S S S S - oxalic acid S U S S S - sodium sulphide S U S S S - perchloric acid (10%) S U M S M M sodium thiosulphate S S S S S - perchloric acid (70%) M U M S M M Solution 555 (20%) S S S - S - phenol (5%) S U M S S M sucrose S S S S S S phenol (50%) M U M S M M sucrose, alkaline S U S - S S phenylethyl alcohol S - S - S - sulfuric acid (10%) S S M S S S phosphoric acid (10%) S S S S S S sulfuric acid (50%) S U M S S S phosphoric acid (30%) S S S S S S sulfuric acid (cone.) S 1 U S S S 1 - phosphoric acid (85%) S S S S S S tannic acid S - S - S - phosphoric acid (cone.) M U S S M - tetrahydrofuran U U U M U U phosphorus trichloride S U S S S - toluene U U U S U U physiologic fluids S S S S S - trichloracetic acid S M U - S U picric acid S S S S S S trichlorethane U U S S U M potassium acetate S M S - S - trisodium phosphate S - S S S - potassium bromide S S S S S - Triton X-100 S S S - S - potassium carbonate S U S S S - turpentine M U U - M U potassium chlorate S S S S S - urea S S S S S S potassium chloride S S S S S - water S S S S S S potassium hydroxide (5%) S U S S S S xylene U U U S U U S Satisfactory S 1 Discolored M Marginal resistance We recommend test runs under appropriate conditions (speed and duration) U Unsatisfactory, not recommended - Performance unknown, tests recommended Zephiran chloride (1%) S S S - S - zinc chloride S S S S S - zinc sulfate S S S S S - page 7 of 35

8 2.4. Nomograph Relative Centrifugal Force 2. Description page 8 of 35

9 3.1. Glass Tubes Ordering Information Nominal Dimensions (mm) Ø x Length and Form Tube Cap Available Adapters for rotors with the following bores 14 ml 16 ml 50 ml 250 l /Places /Places /Places /Places 3 ml 5 ml 10 x x 75 D - RB B - RB / / / / / 9 10 ml 10 ml 12 ml 15 ml 15 ml 13 x x x x x 98 D - RB D - CB/G B - RB HS- RB D - RB / / * / * / / / / / / / 5 30 ml 30 ml 45 ml 24 x x x ml 60 x 115 B - RB HS- RB B - RB D - RB only for swing-out rotors / / / * / / / * * Bottom Support Pad B Borex Glass CB Conical bottom FL Flange / Rim D Duran Glass RB Round bottom G Graduated HS High Speed Glass page 9 of 35

10 Additional Information and Prices 3.1. Glass Tubes Tube Nominal Filling and Form Tested up to... rpm Tested up to... x g ml 3.2 ml D - RB 5,000 3, ml 4.8 ml B - RB 5,000 *6, ml 8.0 ml D - RB 5,000 3, ml 8.4 ml D - C/G 10,000 *10, ml 15.0 ml HS-RB 9,000 *12, ml 11.4 ml B - RB 7,000 *12, ml 25.0 ml B - RB 5,000 *12, ml 30.0 ml HS-RB 10,000 *12, ml 31.5 ml B - RB 5,000 8, ml ml D - RB 4,000 for swing-out rotors only ml 12.0 ml D - RB 5,000 3, * Speed in rpm in swing-out rotors Closures for Glass Tubes Description Fits for: Rubber cap for glass tubes B Borex Glass CB Conical bottom FL Flange / Rim D Duran Glass RB Round bottom G Graduated HS High Speed Glass Attention: Kindly note packaging sizes for your orders. page 10 of 35

11 3.1. Glass Tubes Adapters/Bottom Support Pads for Glass Tubes Description Number of places For rotor bores Adapter Plastic ml Adapter Plastic ml Adapter Plastic ml Adapter Plastic ml Adapter Plastic ml Adapter Rubber 2 50 ml Adapter Rubber 1 50 ml Adapter Rubber 1 50 ml Adapter Rubber 1 50 ml Adapter Rubber 1 50 ml Adapter Rubber 1 16 ml Adapter Rubber 1 16 ml Adapter Rubber 1 14 ml Bottom Support Pad Rubber 50 ml Bottom Support Pad Rubber 250 ml Bottom Support Pad Rubber 16 ml 4 Attention: Kindly note packaging sizes for your orders. page 11 of 35

12 Ordering Information Available Adapters for rotors with the following bores 14 ml 16 ml 50 ml 250 ml 3.2. Plastic Tubes Nominal Dimensions (mm) Ø x Length and Form Tube Cap /Places /Places /Places /Places 1.5 ml 4.5 ml 5.0 ml 11 x x x 75 PP- CB-Eppendorf PP- RB PS- RB included / / / / / / / / / / / / ml 16 x 76 PP- RB ml 14 ml 14 ml 14 ml 14 ml 16 ml 16 ml 16 ml 16 ml 50 ml 50 ml 50 ml 50 ml 50 ml 50 ml 70 ml 70 ml 94 ml 100 ml 100 ml 120 ml 18 x x x x x x x x x x x x x x x x x x x x x 115 PA- RB PC- RB PE- RB PF- RB PP- RB PC- RB/FL PE- RB/FL PF- RB/FL PPCO(PA)-RB/FL PC- RB/FL PC- RB/FL/LC PE- RB/FL PF- RB/FL PPCO(PA)-RB/FL PPCO(PA)-RB/FL/LC PC- RB/G PP- RB PP- RB PC- RB/G PC- RB/G PP- RB included included / / / / / / / / / / 1 PA Polyallomer CB Conical bottom FL Flange / Rim PPCO Polypropylene Copolymer RB Round bottom G Graduated PP Polypropylene LC Loop cap PE Polyethylene PF Polyflor PC Polycarbonate PS Polystyrene page 12 of 35

13 3.2. Plastic Tubes GmbH Additional Information and Prices Tube Nominal Filling and Form Tested up to... rpm Tested up to... x g ml 1.5 ml PP-CB-Eppendorf ( St.) * 16,000 30,000 pack ml 4.5 ml PS-RB (1.000 St.) 5,000 2,500 pack ml 4.5 ml PP-RB (1.000 St.) 20,000 36,000 pack ml 11.3 ml PC-RB 24,000 59, ml 10.8 ml PP-RB 20,000 41, ml 10.7 ml PF-RB 20,000 41, ml 12.5 ml PP-RB 12,000 16, ml 11.5 ml PE-RB 20,000 41, ml 10.8 ml PA-RB 24,000 59, ml 15.5 ml PC-RB/FL 24,000 70, ml 14.5 ml PPCO(PA)-RB/FL 24,000 70, ml 15.0 ml PE-RB/FL 20,000 49, ml 14.5 ml PF-RB/FL 20,000 49, ml 60.0 ml PC-RB/G 8,000 7, ml 42.8 ml PC-RB/FL 24,000 69, ml 42.8 ml PC-RB/FL/LC * 24,000 69, ml 40.9 ml PE-RB/FL 20,000 48, ml 42.1 ml PPCO(PA)-RB/FL/LC * 24,000 69, ml 40.0 ml PF-RB/FL 20,000 48, ml 42.1 ml PPCO(PA)-RB/FL 24,000 69, ml 62.0 ml PP-RB 8,000 7, ml ml PC-RB/G 8,000 8, ml ml PP-RB 6,000 5, ml ml PC-RB/G 8,000 8,586 2 * Cap included PA Polyallomer CB Conical bottom FL Flange / Rim PPCO Polypropylene Copolymer RB Round bottom G Graduated PP Polypropylene LC Loop cap PE Polyethylene PF Polyflor PC Polycarbonate PS Polystyrene Attention: Kindly note packaging sizes for your orders. page 13 of 35

14 3.2. Plastic Tubes Closures for Plastic Tubes Description Fits for: Cap for 14 tubes (PA, PC, PF, PP) and for 16 ml tubes (PPCO(PA), PF, PC) Cap for 14 ml + 16 ml tubes (PE) Cap for 50 ml tubes (Loop Cap) Attention: Kindly note packaging sizes for your orders. page 14 of 35

15 Adapter for Plastic Tubes 3.2. Plastic Tubes Description Number of places For rotor bores Adapter Plastic 4 50 ml Adapter Plastic 2 50 ml Adapter Plastic 2 50 ml Adapter Plastic 1 50 ml Adapter Plastic 1 16 ml Adapter Plastic 1 14 ml Adapter Plastic 1 16 ml Adapter Plastic 1 14 ml Adapter Plastic ml Adapter Plastic ml Adapter Plastic ml Adapter Plastic ml 2 Attention: Kindly note packaging sizes for your orders. page 15 of 35

16 3.3. Advanced Oak Ridge Tubes Ordering Information Available Adapters for rotor bores 50 ml 94 ml Nominal Dimensions (mm) Ø x Length and Form Tube complete Tube Cap O-Rings (3 units ) 10 ml 10 ml 10 ml 10 ml 16 x x x x 80 PPCO(PA) - AOR PC - AOR PE - AOR PF - AOR ml 30 ml 30 ml 30 ml 25 x x x x 92 PPCO(PA) - AOR PC - AOR PE - AOR PF - AOR ml 50 ml 50 ml 50 ml 80 ml 80 ml 80 ml 80 ml 29 x x x x x x x x 105 PPCO(PA) - AOR PC - AOR PE - AOR PF - AOR PPCO(PA) - AOR PC - AOR PE - AOR PF - AOR 1 These screw caps are made of Polyflor too Overwind-protected and gas-tight The ultimate seal for both routine and special applications and high demands on speed. Unique combination of screw cap and conical push-in stopper. The Advanced Oak Ridge (AOR) system is an excellent choice for preparative centrifugation applications including protein purification, cell harvesting, pelleting applications, sterile centrifugation, extractions, density gradients and biohazardous applications. The polypropylene sealing cap's inner conical plug has three self-seal pressure rings. They push against the inside of the tube neck, forming a triple contact seal which adds to the normal screw cap. The cap is constructed to support the tube's shoulder and neck during centrifugation. It includes a grip for easy extraction from the rotor bores. Tubes are of universal sizes and will fit rotors and adapters from all major centrifuge manufacturers. Note: For biohazardous applications the use of optional o-rings is recommended as double seal for added safety benefits (included with all tubes with cap, except for 10 ml PPCO + PC and 30 ml PE). PA Polyallomer PF Polyflor PC Polycarbonate PPCO Polypropylene Copolymer PE Polyethylene page 16 of 35

17 3.3. Advanced Oak Ridge Tubes Additional Information and Prices Tubes complete with cap Tube Nominal Filling and Form Tested up to... rpm Tested up to... x g ml 9.4 ml PC - AOR 24,000 57, ml 8.9 ml PPCO(PA) - AOR 24,000 57, ml 9.7 ml PE - AOR 18,000 32, ml 9.4 ml PF - AOR 20,000 40, ml 27.9 ml PC - AOR 24,000 64, ml 25.9 ml PPCO(PA) - AOR 24,000 64, ml 24.5 ml PE - AOR 10,000 11, ml 26.4 ml PF - AOR 24,000 64, ml 40.0 ml PC - AOR 24,000 69, ml 38.0 ml PPCO(PA) - AOR 24,000 69, ml 38.9 ml PE - AOR 12,000 17, ml 42.6 ml PF - AOR 18,000 39, ml 73.1 ml PC - AOR 20,000 50, ml 76.3 ml PPCO(PA) - AOR 20,000 50, ml 69.3 ml PE - AOR 12,000 18, ml 73.0 ml PF - AOR 15,000 28,174 2 PA Polyallomer PF Polyflor PC Polycarbonate PPCO Polypropylene Copolymer PE Polyethylene Attention: Kindly note packaging sizes for your orders. page 17 of 35

18 3.3. Advanced Oak Ridge Tubes Additional Information and Prices Tubes without cap Tube Nominal Filling and Form Tested up to... rpm Tested up to... x g ml 9.4 ml PC - AOR 24,000 57, ml 8.9 ml PPCO(PA) - AOR 24,000 57, ml 9.7 ml PE - AOR 18,000 32, ml 9.4 ml PF - AOR 20,000 40, ml 27.9 ml PC - AOR 24,000 64, ml 25.9 ml PPCO(PA) - AOR 24,000 64, ml 24.5 ml PE - AOR 10,000 11, ml 26.4 ml PF - AOR 24,000 64, ml 40.0 ml PC - AOR 24,000 69, ml 38.0 ml PPCO(PA) - AOR 24,000 69, ml 38.9 ml PE - AOR 12,000 17, ml 42.6 ml PF - AOR 18,000 39, ml 73.1 ml PC - AOR 20,000 50, ml 76.3 ml PPCO(PA) - AOR 20,000 50, ml 69.3 ml PE - AOR 12,000 18, ml 73.0 ml PF - AOR 15,000 28, Closures for Advanced Oak Ridge Tubes Description Fits for: Sealing cap for 10 ml AOR Tubes made of PC and PPCO (PA) Sealing cap for 10 ml PE AOR Tubes Sealing cap for 10 ml PF AOR Tubes Sealing cap for 30 ml AOR Tubes made of PC and PPCO (PA) Sealing cap for 30 ml PE-AOR Tubes Sealing cap for 30 ml PF-AOR Tubes Sealing cap for 50 ml AOR Tubes made of PC and PPCO (PA) Sealing cap for 50 ml PE-AOR Tubes Sealing cap for 50 ml PF-AOR Tubes Sealing cap for 80 ml AOR Tubes made of PC, PPCO (PA) and PE Sealing cap for 80 ml PF AOR Tubes PA Polyallomer PF Polyflor PC Polycarbonate PPCO Polypropylene Copolymer PE Polyethylene Attention: Kindly note packaging sizes for your orders. page 18 of 35

19 O-Rings for Advanced Oak Ridge Tubes Description Fits for: 3.3. Advanced Oak Ridge Tubes O-Ring for 10 ml AOR PE and PF O-Ring for 30 ml AOR PPCO(PA) and PC O-Ring for 30 ml AOR PF O-Ring for 50 ml AOR PPCO(PA) and PC O-Ring for 50 ml AOR PF O-Ring for 80 ml AOR PPCO(PA) and PC O-Ring for 80 ml AOR PE O-Ring for 80 ml AOR PF Adapter for Advanced Oak Ridge Tubes Description Number of Places For Rotor Bores Adapter Plastic 1 50 ml Adapter Plastic 1 50 ml 2 PA Polyallomer PF Polyflor PC Polycarbonate PPCO Polypropylene Copolymer PE Polyethylene Attention: Kindly note packaging sizes for your orders. page 19 of 35

20 3.4. Bottles GmbH General Information Overwind-protected and gas-tight One-piece sealing cap with O-ring guarantees leak-proof seal Maximum filling volume and maximum speed Accessories that increase bottle lifespan Available are high-speed centrifuge bottles with volumes of 200, 250, 290, 500, 650, 750 and 1000 ml for angle and swing-out rotors. A special black polypropylene bottle which reduces UV light transmission is available for light-sensitive analyses such as fluorescent studies and work with retinal cells. A wide neck bottle design with gently sloping shoulders allows easy decanting of supernatants without liquid hang-up and pellet disturbance. The cap provides neck support, preventing bottle collapse even after prolonged centrifugation. A polypropylene cover support ring increases the lifespan of the 500 ml bottle by providing extra support to the neck area during centrifugation. The cover support ring can also be used to facilitate opening and closing of the 250, 290 and 500 ml bottles. Note: During an actual centrifugation run the cover support ring should only be used with the 500 ml bottles. The one-piece polypropylene sealing cap with a well-embedded silicone o-ring provides a leak-proof seal and is interchangeable between the 250, 290, 500 and 1000 ml bottles. The cap is molded to match exactly the threads of the bottle and provides a leak-proof seal. A tight seal is guaranteed even at maximum speed. Polypropylene pads are available for use with the 250 and 290 ml flat bottom bottles and the 250 ml round bottom bottles. The pads fill the gap that would exist between the bottle bottom and the rotor cavity, eliminating unnecessary stress and cold flow of the plastics in this area during the run. page 20 of 35

21 3.4. Bottles GmbH Ordering Information Nominal Dimensions (mm) Ø x Length and Form Bottles complete Bottles Cap O-Rings (3 pieces ) Bottom Support Pads for rotor bores 250 ml 500 ml 200 ml 200 ml 200 ml 200 ml 56 x x x x 112 PC CB/W PC FB/W PPCO(PA) CB/W PPCO(PA) FB/W ml 250 ml 250 ml 250 ml 250 ml 250 ml 250 ml 250 ml 250 ml 250 ml 290 ml 290 ml 500 ml 500 ml 500 ml 500 ml 500 ml 650 ml 650 ml 750 ml 750 ml 1,000 ml 1,000 ml 1,000 ml 1,000 ml 62 x x x x x x x x x x x x x x x x x x x x x x x x x 175 PC FB/W PC RB/W PE FB/W PE RB/W PF FB/W PF RB/W PP/black FB/W PPCO(PA) FB/W PPCO(PA) RB/W PP RB/W PC FB/W PE FB/W PC FB/W PE FB/W PP/black FB/W PPCO(PA) FB/W PPCO(PA) FB/W PC FB/W PP FB/W PC FB/W PPCO(PA) FB/W PC FB/W PC FB/W + SR PPCO(PA) FB/W PPCO(PA) FB/W+SR Bottom support pads not for use in all swing-out rotors and angle rotors JA-14 (Beckman) and HFA (Heraeus) and AF AF (Herolab). 2 For safety reasons always use with cover support ring ( ). Bottles cannot be used in rotor JA-10 (Beckman) ml bottles do not fit in rotors AF (Herolab) and included included AS only JA-14 (Beckman) PA Polyallomer CB Conical bottom FL Flange / Rim PPCO Polypropylene Copolymer FB Flat bottom G Graduated PP Polypropylene RB Round bottom LC Loop cap PE Polyethylene W Wide neck PC Polycarbonate PF Polyflor SR Support ring page 21 of 35

22 3.4. Bottles GmbH Additional Information and Prices Bottles complete with cap Tube Nominal Filling and Form Tested up to rpm Tested up to x g ml ml PC FB/W 10,000 16, ml ml PPCO FB/W 10,000 16, ml ml PC CB/W 10,000 16, ml ml PPCO(PA) CB/W 10,000 16, ml ml PC FB/W 14,400 33, ml ml PP/black FB/W 13,000 27, ml ml PPCO(PA) FB/W 14,400 33, ml ml PE FB/W 13,500 29, ml ml PF FB/W 12,000 23, ml ml PC RB/W 14,400 33, ml ml PP RB/W 14,400 33, ml ml PPCO(PA) RB/W 14,400 33, ml ml PE RB/W 13,500 29, ml ml PF RB/W 12,000 23, ml ml PC FB/W 14,400 33, ml ml PE FB/W 13,500 29, ml ml PC FB/W 10,500 20, ml ml PP/black FB/W 10,500 20, ml ml PPCO(PA) FB/W 10,500 20, ml ml PE FB/W 7,500 10, ml ml PPCO(PA) FB/W 5,200 5, ml ml PC FB/W 3 4,000 4, ml ml PP FB/W 3 4,000 4, ml ml PC FB/W 3 4,000 4, ml ml PPCO(PA) FB/W 3 4,000 4, ,000 ml ml PC FB/W 3 4,000 4, ,000 ml ml PC FB/W / SR 8,000 12, ,000 ml ml PPCO(PA) FB/W 3 4,000 4, ,000 ml ml PPCO(PA) FB/W SR 8,000 12, For safety reasons always use with cover support ring ( ). Bottles cannot be used in rotor JA-10 (Beckman). 3 If used with Sealing cap/support ring Combination (cat. no ) the max speed is 8,000 rpm in a fixed angle rotor. PA Polyallomer CB Conical bottom FL Flange / Rim PPCO Polypropylene Copolymer FB Flat bottom G Graduated PP Polypropylene RB Round bottom LC Loop cap PE Polyethylene W Wide neck PC Polycarbonate PF Polyflor SR Support ring Attention: Kindly note packaging sizes for your orders. page 22 of 35

23 3.4. Bottles GmbH Additional Information and Prices Bottles without cap Tube Nominal Filling and Form Tested up to rpm Tested up to x g ml ml PC FB/W 10,000 16, ml ml PPCO FB/W 10,000 16, ml ml PC CB/W 10,000 16, ml ml PPCO(PA) CB/W 10,000 16, ml ml PC FB/W 14,400 33, ml ml PPCO(PA) FB/W 14,400 33, ml ml PE FB/W 13,500 29, ml ml PF FB/W 12,000 23, ml ml PC - RB/W 14,400 33, ml ml PP - RB/W 14,400 33, ml ml PPCO(PA) RB/W 14,400 33, ml ml PE - RB/W 13,500 29, ml ml PF RB/W 12,000 23, ml ml PC - FB/W 14,400 33, ml ml PE - FB/W 13,500 29, ml ml PC - FB/W 10,500 20, ml ml PPCO(PA) FB/W 10,500 20, ml ml PE - FB/W 9,000 14, ml ml PPCO(PA) FB/W 5,200 5, ml ml PC - FB/W 4,000 4, ml ml PP - FB/W 4,000 4, ml ml PC - FB/W 4,000 4, ml ml PPCO(PA) FB/W 4,000 4, ,000 ml ml PC - FB/W 4,000 4, ,000 ml ml PPCO(PA) FB/W 4,000 4, For safety reasons always use with cover support ring ( ). Bottles cannot be used in rotor JA-10 (Beckman). PA Polyallomer CB Conical bottom FL Flange / Rim PPCO Polypropylene Copolymer FB Flat bottom G Graduated PP Polypropylene RB Round bottom LC Loop cap PE Polyethylene W Wide neck PC Polycarbonate PF Polyflor SR Support ring Attention: Kindly note packaging sizes for your orders. page 23 of 35

24 3.4. Bottles GmbH Closures and Support Rings for Bottles Description Fits for: Sealing cap for 200 ml Sealing cap for 250, 290, 500 und 1,000 ml Combination (for 1,000 ml) Sealing cap with support ring Sealing cap for 250 ml PF Support ring for 500 ml cap and closing device for 250/290/500 ml O-Rings for Bottle Sealing Caps Description Fits for: O-Ring for bottle sealing caps 200 ml O-Ring for bottle sealing caps O-Ring for bottle sealing caps (PF bottles) Bottom Support Pads for Bottles Description Fits for: Bottom support pad for 250/290 ml FB Bottom support pad for 250 ml RB Attention: Kindly note packaging sizes for your orders. page 24 of 35

25 New: Centrifuge Bottles with wide mouth - 70 mm : PPCO PPCO- Bottles 70 mm neck Dimensions Tested up to Bottle with Cover Bottle w./o. Cover Cover 750 ml Ø 100 x 143 mm For Fixed angle rotor 8,000 rpm / 12,042 x g 950 ml Ø 100 x 167 mm blue cap white cap For Fixed angle rotor 8,000 rpm / 12,042 x g 1,000 ml Ø 100 x 181 mm For Fixed angle rotor 8,000 rpm / 12,042 x g 1,000 ml Ø 98 x 190 mm For Fixed angle rotor 8,000 rpm / 12,042 x g 750 ml Ø 100 x 130 mm For Swing-out rotor 4,100 rpm / 5,394 x g ml Ø 100 x 154 mm For Swing-out rotor 4,100 rpm / 5,394 x g black cap 1,000 ml Ø 100 x 168 mm For Swing-out rotor 4,100 rpm / 5,394 x g page 25 of 35

26 Ordering Information Tubes 3.5. Ultra Centrifuge Tubes and Bottle Nominal Dimension (mm) Ø x Length and Form Tubes Cap Fits into these rotors: 2.0 ml 2.0 ml 8 x 51 8 x 51 PA- thin-walled PC- thick-walled TFT 80.2, TST ml 4.4 ml 4.4 ml 11 x x x 60 PA- thin-walled PC- thick-walled PC- thick-w. w. thread TFT 80.4, TST 60.4 SW 60Ti, SW 56Ti 5.0 ml 5.0 ml 5.0 ml 13 x x x 51 PA- thick-walled PA- thin-walled PC- thick-walled TST 55.5, AH-650, SW 65 SW 55Ti, SW 50.1, SW 50 SW 39, TLA ml 6.5 ml 6.5 ml 6.5 ml 13.2 ml 13.5 ml 13.5 ml 13.5 ml 14.0 ml 14.0 ml 17.0 ml 17.0 ml 38.5 ml 38.5 ml 38.5 ml 38.5 ml 94.0 ml 94.0 ml 94.0 ml 13 x x x x x x x x x x x x x x x x x x x 102 PA- thick-walled PA- thin-walled PC- thick-walled PC- thick-w. w. thread PA- thin-walled PA- thin-walled PC- thick-walled PC- thick-w. w. thread PA- thin-walled PC- thick-walled PA- thin-walled PC- thick-walled PA- thick-walled PA- thin-walled PC- thick-walled PC- thick-w. w. thread PA- thick-walled PC- thick-walled PC- thick-w. w. thread Ordering Information Ultra-Centrifuge Bottle with Delrin closure and Neopren ring for ultra-rotors TFA and Type 19 Nominal Dimension (mm) Ø x Length and Form (with closure) Bottle complete Bottle only Cap TFT Ti, 50.3Ti, 40.3 TST 41.13, SW 41Ti TFT 80.13, TFT 75.13, TFT TFT 60.13, TFT 50.13, TFT Ti, 75Ti, 70.1Ti, 65, 50Ti, 40, SW 36 TST 41.14, SW 40Ti TST 28.17, AH-629 SW 27.1, SW 28.1 TFT 70.38, TFT 65.38, TFT TFT 50.38, TST 28.38, AH Ti, 60Ti, 55.2Ti, 30.2Ti 42.1, SW 27, (SW 28 without lid) TFT 45.94, 45Ti, 35 O-Rings (3 pieces ) 250 ml 60 x 122 PA - FB/W Note: This ultra-centrifuge bottle has other dimensions than a high-speed bottle with the same volume. Hence they will not fit the bores of high-speed rotors and vice versa. PA Polyallomer FB Flat bottom W Wide neck PC Polycarbonate RB Round bottom page 26 of 35

27 3.5. Ultra Centrifuge Tubes and Bottle Additional Information and Prices Tubes without cap Tube Nominal Filling and Form Speed max... rpm (cpltly. filled) Former Kontron No ml 0.6 ml PC-thick-walled 45, ml 1.3 ml PA-thin-walled 80, ml 3.3 ml PA-thin-walled 80, ml 2.2 ml PC-thick-walled 50, ml 2.7 ml PC-thick-w. w. thread 50, ml 5.0 ml PA-thin-walled 55, ml 3.4 ml PC-thick-walled 55, ml 3.4 ml PA-thick-walled 50, ml 2.8 ml PC-thick-walled 40, ml 4.5 ml PC-thick-w. w. thread 45, ml 5.8 ml PA- thin- walled 45, ml 2.8 ml PA- thick- walled 35, ml 11.3 ml PA- thin- walled 41, ml 11.0 ml PA- thin- walled 80, ,5 ml 8.5 ml PA- thin- walled 45, ml 8.5 ml PC- thick- walled 40, ml 9.5 ml PC- thick- w. w. thread 40, ml 12.0 ml PA- thin- walled 41, ml 9.0 ml PC- thick- walled 30, ml 15.8 ml PA- thin- walled 28, ml 12.5 ml PC- thick- walled 28, ml 32.5 ml PC- thick- w. w. thread 50, ml 29.0 ml PC- thick- walled 50, ml 34.0 ml PA- thin- walled 70, ml 29.0 ml PA- thick- walled 45, ml 77.0 ml PA- thick- walled 45, ml 77.0 ml PC- thick- walled 45, ml 88.0 ml PC- thick- w. w. thread 40, Tubes were tested at 4 C for 24 hours. Since there are many factors that may influece the performance characteristics and lifespan of centrifuge tubes the information given above has been compiled as a general guideline but, in no case, expresses absolute guarantee of a product in a laboratory situation Additional Information and Prices Bottle Bottle Nominal Filling and Form Speed max... rpm (cpltly. filled) Former Kontron No ml ml PA - FB/W without cap 20, ml ml PA - FB/W complete with cap 20, PA Polyallomer FB Flat bottom W Wide neck PC Polycarbonate RB Round bottom Attention: Kindly note packaging sizes for your orders page 27 of 35

28 3.5. Ultra Centrifuge Tubes and Bottle Closures for Ultra-Centrifuge Tubes and Bottle All closures are overwind-protected and gas-tight. Description Fits for: Former Kontron No Sealing cap fur UC bottle Screw cap for 94 ml Screw cap for 38.5 ml Screw cap for 13.5 ml Screw cap for 6.5 ml Screw cap for 4.4 ml O-Rings for Ultra-Centrifuge Tubes and Bottle Description Fits for: Former Kontron No O-Rings for UC bottle O-Ring for screw cap 94 ml O-Ring for screw cap 38.5 ml O-Ring for screw cap 13.5 ml O-Ring for screw cap 6.5 ml O-Ring for screw cap 4.4 ml Other accessories for Ultra-Centrifuge Tubes Description Former Kontron No Extractor Tool for UC tubes Attention: Kindly note packaging sizes for your orders. page 28 of 35

29 3.6. Other Accessories Accessories Description Extractor tool for 50 ml with rim Extractor tool for bottom support pads Extractor tool M Extractor tool M Cleaning brush for all rotors 50 ml Cleaning brush for all rotors 14/15/16 ml Cleaning brush for all rotors 250/290 ml Rotor stand for all rotors with conical bore (e. g. for Sorvall etc.) 1 Attention: Kindly note packaging sizes for your orders. page 29 of 35

30 approx. Ø in mm of Rotor Bore x max. length GmbH The tubes will fit into the next larger sized rotor with adapters from all manufacturers. Swing-out Rotors are listed without the bucket resp. adapter numbers. Manufacturers not listed have in most cases an identical size of the rotor compartments. The given information is as accurate as possible. Errors or incompleteness could be contained. Herolab is not responsible for any damage caused by the given information. Herolab reserves the right to modify any part without prior notice. 4. Compatibility with rotors of other manufacturers 10 ml 16.1 x ml 25.3 x ml 28.7 x 103 Herolab AFH or AF Sigma 12111, 12141, and Beckman JA-21, JS-24.15, F1010 and S0410 Sigma 12139, and Beckman JS-24.38, F0630 Hermle V02, V03 and V02 Herolab AF , A 8.24, AF , A 12.17, AS 4.7 and AS 4.13 Sigma 12150, and Jouan AK(L) 50.22, AK(L) and FAJ-20C Sorvall SS-34, SA-300, SA-600, F-28/50, A-500, A/S-400, LA/S-400, SL-50RT, HB-4 and HB-6 Beckman JA-20, JA-12, JA-17, JA-25.50, JA-30.50Ti, JS-13, JS-13.1, F0650, F0850 and TA Fiberlite F21(B,S or J)8x50(y) and F18(B,S or J)12x50(y) Hermle V02, V03 and V01 80 ml 38.1 x ml 56.5 x ml 61.8 x ml 61.8 x ml 69.5 x ml 97.5 x 114 Herolab AS ml 97.5 x 136 Herolab AFH or AF 6.94 (6.80), A 8.20 and AS 4.13 Sigma , and Jouan AG , AG , AK(L) , SWK and SWG Sorvall SA-800 Beckman JA-18, F0485, F0685 and FX6100 Fiberlite F20(B,S or J)6x100 Hermle V02, V03, V01 and V01 Herolab ASH 4.055, AS or TS Sigma 11133, 11140, 11150, 11156, 11180, 11650, and Herolab AF 6.250, AF 8.250, A 6.14, AFH and AS 4.7 Sigma 11150, 11180, 11650, 11800, 11801, and Jouan AG 290.9, AK(L) and FAJ-14C Sorvall GSA, SLA-1000, SLA-1500, SLC-1500, H-1000B, RTH-250, H-2000B and HS-4 Beckman JA-14, JLA , TA , JS-7.5 and SX4250 Fiberlite F14(B,S or J)6x250(y) and F16(B,S or J)4x250(y) Hermle V01, V01 and V01 Herolab A 6.14 Sorvall GSA and SLA-1500 Jouan AG and AK Beckman JA-14, JLA and JS-7.5 Herolab AF 6.500, AF and A 6.9 Sigma 11150, 11650, 11800, 11801, and Jouan FAJ-10C and AK(L) Sorvall GS-3, SLA-3000, SLC-3000 Beckman JLA Fiberlite F10(B,BA,S or J)6x500(y) and F12S6x500y Herolab AS Sigma 11650, and ml 97.5 x ml 97.5 x 175 Herolab AS Sigma 11650, and Sorvall SH-3000, TTH-750 and RTH-750 Beckman JS-4.3 SX4750 SX4750A Hermle V06 Herolab AF , AF and AS Sigma 12510, and Sorvall SLC-4000, SLC-6000, HL-4, HG-4L, H-4000, H-6000 Beckman JS-4.0 Fiberlite F(7S,8B, 9B,9S,9J)4x1000y, F6(B,S or J)6x1000y and F8(B,BA,S or J)6x1000y Hermle V05 page 30 of 35

31 Item Tubes 10 ml PC-AOR without screw cap Tubes 10 ml PPCO-AOR without screw cap Tubes 10 ml PE-AOR without screw cap Tubes 10 ml PF-AOR without screw cap Tubes 30 ml PC-AOR without screw cap Tubes 30 ml PPCO-AOR without screw cap Tubes 30 ml PE-AOR without screw cap Tubes 30 ml PF-AOR without screw cap Tubes 50 ml PC-AOR without screw cap Tubes 50 ml PPCO-AOR without screw cap Tubes 50 ml PE-AOR without screw cap Tubes 50 ml PF-AOR without screw cap Tubes 80 ml PC-AOR without screw cap Tubes 80 ml PPCO-AOR without screw cap Tubes 80 ml PE-AOR without screw cap Tubes 80 ml PF-AOR without screw cap Bottles 200 ml PC-FB without screw cap Bottles 200 ml PP-FB without screw cap Bottles 200 ml PC-CB without screw cap Bottles 200 ml PPCO-CB without screw cap Bottles 250 ml PC-FB without screw cap Bottles 250 ml PPCO-FB without screw cap Bottles 200 ml PA-FB/W UC without screw cap Bottles 250 ml PE-FB without screw cap Bottles 250 ml PF-FB with screw cap Bottles 250 ml PC-RB without screw cap Bottles 250 ml PP-RB without screw cap Bottles 250 ml PPCO-RB without screw cap Bottles 250 ml PE-RB without screw cap Bottles 250 ml PF-RB with screw cap Bottles 290 ml PC-FB without screw cap Bottles 290 ml PE-FB without screw cap Bottles 500 ml PC-FB without screw cap Bottles 500 ml PPCO-FB without screw cap Bottles 500 ml PE-FB without screw cap Bottles 500 ml PPCO-FB without screw cap Bottles 1000 ml PC-FB without screw cap Bottles 1000 ml PPCO-FB without screw cap Bottles 750 ml PC-FB without screw cap Bottles 750 ml PP-FB without screw cap Bottles 650 ml PC-FB without screw cap Bottles 650 ml PP-FB without screw cap Tubes 3 ml Duran Glass. RB Tubes 5 ml Borex Glass, RB Tubes 10 ml Duran Glass, RB Tubes 10 ml Duran Glass, C/G Tubes 15 ml HS Glass, RB Tubes 12 ml Borex Glass, RB Tubes 30 ml Borex Glass, RB Tubes 30 ml HS Glass, RB Tubes 45 ml Borex Glass, RB Tubes 200 ml Duran Glass, RB Tubes 15 ml Duran Glass, RB Tubes 2.0 ml PC thick-walled UC / pck. with 50 pieces Tubes 1.5 ml PP-CB with lid (Eppendorf) / pck. with pieces 1000 page 31 of 35

32 Item Tubes 2.0 ml PA thin-walled UC / pck. with 50 pieces Tubes 4.4 ml PA thin-walled UC / pck. with 50 pieces Tubes 4.4 ml PC thick-walled UC / pck. with 50 pieces Tubes 5.0 ml PA thin-walled UC / pck. with 50 pieces Tubes 5.0 ml PS-RB / pck. with pieces Tubes 4.4 ml PC thick-walled with thread UC / pck. with 50 pieces Tubes 4.5 ml PP-RB / pck. with pieces Tubes 5.0 ml PC thick-walled UC / pck. with 50 pieces Tubes 5.0 ml PA thick-walled UC / pck. with 50 pieces Tubes 6.5 ml PC thick-walled UC / pck. with 50 pieces Tubes 6.5 ml PC thick-walled with thread UC / pck. with 50 pieces Tubes 6.5 ml PA thin-walled UC / pck. with 50 pieces Tubes 6.5 ml PA thin-walled UC / pck. with 50 pieces Tubes 14.0 ml PA thin-walled UC / pck. with 50 pieces Tubes 13.2 ml PA thin-walled UC / pck. with 50 pieces Tubes 10 ml PC-AOR with screw cap Tubes 10 ml PPCO-AOR with screw cap Tubes 13.5 ml PA thin-walled UC / pck. with 50 pieces Tubes 10 ml PE-AOR with screw cap Tubes 10 ml PF-AOR with screw cap Tubes 13.5 ml PC thick-walled UC / pck. with 50 pieces Tubes 13.5 ml PC thick-walled with thread UC / pck. with 50 pieces Tubes 14.0 ml PC thick-walled UC / pck. with 50 pieces Tubes 14 ml PC-RB Tubes 14 ml PP-RB Tubes 14 ml PF-RB Tubes 13.0 ml PP-RB Tubes 17.0 ml PA thin-walled UC / pck. with 50 pieces Tubes 17.0 ml PC thick-walled UC / pck. with 50 pieces Tubes 14 ml PE-RB Tubes 14 ml PA-RB Tubes 16 ml PC-RB/FL Tubes 16 ml PPCO-RB/FL Tubes 16 ml PE-RB/FL Tubes 16 ml PF-RB/FL Tubes 30 ml PC-AOR with screw cap Tubes 30 ml PPCO-AOR with screw cap Tubes 30 ml PE-AOR with screw cap Tubes 30 ml PF-AOR with screw cap Tubes 38.5 ml PC thick-walled with thread UC / pck. with 50 pieces Tubes 38.5 ml PC thick-walled UC / pck. with 50 pieces Tubes 38.5 ml PA thin-walled UC / pck. with 50 pieces Tubes 38.5 ml PA thick-walled UC / pck. with 50 pieces Tubes 70 ml PC-RB/G Tubes 50 ml PC-RB/FL Tubes 50 ml PC-RB/FL with Loop Cap Tubes 50 ml PE-RB/FL Tubes 50 ml PPCO-RB/FL with Loop Cap Tubes 50 ml PF-RB/FL Tubes 50 ml PPCO-RB/FL Tubes 70 ml PP-RB Tubes 50 ml PC-AOR with screw cap Tubes 50 ml PPCO-AOR with screw cap Tubes 50 ml PE-AOR with screw cap 10 page 32 of 35

33 Item Tubes 50 ml PF-AOR with screw cap Tubes 80 ml PC-AOR with screw cap Tubes 80 ml PPCO-AOR with screw cap Tubes 80 ml PEC-AOR with screw cap Tubes 80 ml PF-AOR with screw cap Tubes 94.0 ml PA thick-walled UC / pck. with 25 pieces Tubes 94.0 ml PC thick-walled UC / pck. with 25 pieces Tubes 94.0 ml PC thick-walled with thread UC / pck. with 25 pieces Tubes 100 ml PC-RB/G Tubes 120 ml PP-RB Tubes 100 ml PC-RB/G Bottles 200 ml PC-FB with screw cap Bottles 200 ml PPCO-FB with screw cap Bottles 200 ml PC-CB with screw cap Bottles 200 ml PPCO-CB with screw cap Bottles 250 ml PC-FB with screw cap Bottles 250 ml PP black FB with screw cap Bottles 250 ml PPCO-FB with screw cap Bottles 200 ml PA-FB/W UC with screw cap Bottles 250 ml PE-FB with screw cap Bottles 250 ml PF-FB with screw cap Bottles 250 ml PC-RB with screw cap Bottles 250 ml PP-RB with screw cap Bottles 250 ml PPCO-RB with screw cap Bottles 250 ml PE-RB with screw cap Bottles 250 ml PF-RB with screw cap Bottles 290 ml PC-FB with screw cap Bottles 290 ml PE-FB with screw cap Bottles 500 ml PC-FB with screw cap Bottles 500 ml PP black-fb with screw cap Bottles 500 ml PPCO-FB with screw cap Bottles 500 ml PE-FB with screw cap Bottles 500 ml PPCO-FB with screw cap (for rotor AS only) Bottles 1000 ml PC-FB with screw cap Bottles 1000 ml PC-FB with screw cap and support ring Bottles 1000 ml PPCO-FB with screw cap Bottles 1000 ml PPCO-FB with screw cap and support ring Bottles 750 ml PC-FB with screw cap Bottles 750 ml PP-FB with screw cap Bottles 650 ml PC-FB with screw cap Bottles 650 ml PP-FB with screw cap Cap for tubes 14 ml PA + 16 ml PPCO. PC Cap for tubes 14 ml PE + 16 ml PE Cap for tubes (Loop Cap) for tubes 50 ml FL Cap for AOR tubes 10 ml PC. PPCO Cap for AOR tubes 10 ml PE Cap for AOR tubes 10 ml PF Cap for AOR tubes 30 ml PC. PPCO Cap for AOR tubes 30 ml PE Cap for AOR tubes 30 ml PF Cap for AOR tubes 50 ml PC. PPCO Cap for AOR tubes 50 ml PE Cap for AOR tubes 50 ml PF Cap for AOR tubes 80 ml PC. PPCO Cap for AOR tubes 80 ml PE 10 page 33 of 35

34 Item Cap for AOR tubes 80 ml PF Rubber cap for glass tubes Screw cap for bottles 200 ml 6 Screw cap for bottles ml Screw cap for bottles 1000 ml with support ring (black) Screw cap for bottles 250 ml PF Screw cap for bottles 250 ml PA UC Screw cap, aluminum, for UC tubes 94 ml Screw cap, aluminum, for UC tubes 38.5 ml Screw cap, aluminum, for UC tubes 13.5 ml Screw cap, aluminum, for UC tubes 6.5 ml Screw cap, aluminum, for UC tubes 4.4 ml Extractor tool for UC tubes Adapter 50 ml Rotor bore / 4 x 1 ml Adapter 2.2 ml Rotor bore / Micro tubes ml / Pck. with 6 pieces Adapter 2.2 ml Rotor bore / Micro tubes ml / Pck. with 6 pieces Adapter 2.2 ml Rotor bore / Micro tubes 0.2 ml PCR / Pck. with 6 pieces Adapter 50 ml Rotor bore / 2 x 1.5 ml Eppendorf Adapter 50 ml Rotor bore / 2 x 4.5/5 ml Adapter 50 ml Rotor bore / 1 x 10 ml AOR Adapter 50 ml Rotor bore / 1 x 16 ml Adapter 50 ml Rotor bore / 1 x 30 ml AOR Adapter 50 ml Rotorbore Falcon / 1x 30 ml AOR Adapter 16 ml Rotor bore / 1 x 1.5 ml Eppendorf Adapter 14 ml Rotor bore / 1 x 1.5 ml Eppendorf Adapter 16 ml Rotor bore / 1 x 4.5/5 ml Adapter 14 ml Rotor bore / 1 x 4.5/5 ml Adapter 250 ml Rotor bore / 15 x 3 ml glass tubes Adapter 250 ml Rotor bore / 9 x 4.5/5 ml plastic tubes or 5 ml glass tubes Adapter 250 ml Rotor bore / 9 x 10 ml glass tubes (Ø 13 mm) Adapter 250 ml Rotor bore / 5 x 16 ml plastic or 12/15 ml glass tubes (Ø 18 mm) Adapter 250 ml Rotorbore / 5 x 15 ml Falcon Adapter 250 ml Rotor bore / 3 x 30 ml glass tubes Adapter 250 ml Rotor bore / 1 x 100/120 ml (Ø 40 mm) Adapter 250 ml Rotorbore / 1x Falcon 50 ml Adapter (Bottom Pad) 250 ml Rotor bore / 1 x 250/290 ml bottles FB Adapter (Bottom Pad) 250 ml Rotor bore / 1 x 250/290 ml bottles RB Adapter 250 ml Rotor bore / 15 x 1.5 ml Eppendorf Support ring for bottles 500 ml / Closing device for bottles ml Adapter 50 ml Falcon / 1 x 15 ml Falcon Adapter 50 ml Rotor bore / 2 x 3 ml glass tubes Adapter 50 ml Rotor bore / 1 x 10 ml glass tubes Adapter 50 ml Rotor bore / 1 x 10 ml glass tubes with conical bottom Adapter 50 ml Rotor bore / 1 x 12 ml glass tubes Adapter 50 ml Rotor bore / 1 x 30 ml glass tubes Adapter 16 ml Rotor bore / 1 x 3 ml glass tubes Adapter 16 ml Rotor bore / 1 x 10 ml glass tubes (Ø 13 mm) Adapter 14 ml Rotor bore / 1 x 5 ml glass tubes Adapter (Bottom Pad) 50 ml Rotor bore / 1 x 45 ml glass tubes Adapter (Bottom Pad) 250 ml Rotor bore / 1 x 200 ml glass tubes Adapter (Bottom Pad) 16 ml Rotor bore / 1 x 12/15 ml glass tubes (Ø 18 mm) O-Ring for screw caps of bottles 200 ml / pck. with 3 pieces 3 page 34 of 35

35 Item O-Ring for screw caps of bottles ml / pck. with 3 pieces O-Ring for screw caps of bottles ml PF O-Ring for screw caps of bottles 250 ml PA UC / pck. with 3 pieces O-Ring for AOR tubes 10 ml PE. PF / pck. with 3 pieces O-Ring for AOR tubes 30 ml PPCO. PC / pck. with 3 pieces O-Ring for AOR tubes 30 ml PF / pck. with 3 pieces O-Ring for AOR tubes 50 ml PPCO. PC / pck. with 3 pieces O-Ring for AOR tubes 50 ml PF / pck. with 3 pieces O-Ring for AOR tubes 80 ml PPCO. PC / pck. with 3 pieces O-Ring for AOR tubes 80 ml PE / pck. with 3 pieces O-Ring for AOR tubes 80 ml PF / pck. with 3 pieces O-Ring for screw cap. aluminum for UC tubes 94 ml O-Ring for screw cap. aluminum for UC tubes 38.5 ml O-Ring for screw cap. aluminum for UC tubes 13.5 ml O-Ring for screw cap. aluminum for UC tubes 6.5 ml O-Ring for screw cap. aluminum for UC tubes 4.4 ml Extractor tool for tubes 50 ml with FL Extractor tool M Rotor stand for all rotors with conical bore Cleaning brush for all rotors 50 ml Cleaning brush for all rotors 14/15/16 ml Cleaning brush for all rotors 250/290 ml Extractor tool for bottom support pad Extractor tool M4 1 page 35 of 35