80 mm / 100 mm (for modular width 5000 mm) 120 mm with drive 240 mm for manual operation 120 mm with drive 240 mm for manual operation

Transcription

1 Garage doors

2 Program overview Up-and-over garage doors and side doors Product Up-and-over door DL Ordering dimensions width/height in mm (modular dimensions) W mm H mm Min. headroom Min. lateral projection left/right Page 5-6 Up-and-over door DF (double garage door) Garage side door ew-1 (steel hollow profile) W max / 5000 mm H max / 2250 mm W mm H mm 80 mm / 100 mm (for modular width 5000 mm) 120 / 120 mm 200 / 200 mm (for modular width 5000 mm) Garage side door ew-2 (steel hollow profile) W mm H mm Garage side door RP-1 (single-walled) W mm H mm Garage side door RP-2 (single-walled) W mm H mm Garage sectional doors and side doors Product Sectional door Type GSW 40-S Sectionaltor Type GSW 40-L Ordering dimensions width/height in mm (modular dimensions) W mm H mm W mm H mm Min. headroom 120 mm with drive 240 mm for manual operation 120 mm with drive 240 mm for manual operation Min. lateral projection left/right Page 82.5 mm mm Sectional door Type GSH W mm H mm 120 mm with drive 240 mm for manual operation 82.5 mm Sectional door side door Type GSW 40-L W mm H mm Sectional door side door Type GSH W mm H mm Garage door drives drive system 12.2; 20.2;

3 Up-and-over garage door DL Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Ready-to-install up-and-over garage door DL. Single-leaf element. Type of handing: behind the opening. Door leaf filling: galvanized, vertically ribbed sheet steel, powder coated similar to RAL 9016 (Traffic white). 3-sided galvanized block frame with ceiling guide rail. Lateral lever arms with 3-fold spring system and finger pinch protection. Lateral plastic cover strips. Lateral locking with special plastic catches. Special lock with profile half cylinder and plastic round handle set with pull cord. 2 plastic rollers Ø 50 mm. Teckentrup DL or equivalent. Unit price Total price Technical data Product: Up-and-over garage door DL Installation in: Masonry Concrete Dimensions: Width: mm Height: mm Handing: Door leaf: Door leaf thickness: Frame: Surface: Pre-assembled up-and-over garage door for handing behind or in the opening. Door leaf frame: 3-sided galvanized block frame Reinforcement: 2 reinforcements, 1 mm thick Filling: Ribbed door: galvanized sheet steel, vertically ribbed, optionally horizontally ribbed. Panelled door (Georgian/cassette) made of galvanized thin sheet. Panelled door: galvanized sheet steel 1 mm thick. Wooden door: type of wood, vertical Norway spruce, optionally horizontal or fishbone, door leaf frame without plinth. Special equipment - filling: Steel panels with ventilation openings, Corrugated grille Horizontal Norway spruce panels, Wooden fishbone panels with mullion 50 mm 3-sided galvanized block frame with ceiling guide rail. Block frame with groove and PVC contact strip. Lateral lever arms with 3-fold spring system and finger pinch protection. Lateral plastic cover strips. 3 wall anchor plugs on each side and 1 x top, 2 threshold anchors Ribbed/Panelled door: powder coated Traffic white, similar to RAL Panelled door (Georgian/cassette) woodgrain, powder coated Traffic white, similar to RAL Special coating for ribbed and panelled doors: trend colours RAL of your choice (Avoid dark colours for doors subject to direct sunlight, since cracks and warpage of the door leaf cannot be completely prevented. Pearleffect, fluorescent and metallic colours are only possible after individual clarification.) Wooden door: vertical Norway spruce, optionally horizontal or fishbone. Door leaf frame without plinth, powder coated Sepia brown (RAL 8014). The wood has been factory protected against fungal decay, decay and wood pests with a colourless impregnating solution. Final treatment is carried out by the customer with a final protective coat. Fittings: Spring-loaded special lock with profile half cylinder, lateral lock with special plastic catches. Black plastic round handle with pull cord 2 rollers Ø 50 mm, 12 mm wide Special equipment: Wicket door (outward opening), specify type of handing. Garage door drive, radio control with handheld transmitter, key holder Lock set for vertical locking with electric drive (vertical locking for version with wicket door) Lock set for horizontal locking with electric drive retrofit kit Header casing max. 500 mm (same as door leaf) Third lock Standard sizes: Ordering size: from 1750 x 1875 up to 2750 x 2500/ 3000 x 2375 mm Ordering size/ Modular dim x x x x x x Clear passage size 2115 x x x x x x Subject to technical changes. 5

4 Up-and-over garage door DL + 20 mm (Insertion depth) Clear finished dimension UFL FFL Screed Installation behind the opening Installation in the opening Overall frame dimension Clear finished dimension Inside Overall frame dimension Clear finished dimension Inside UFL FFL FFL UFL Overall frame dimension Inside Inside Clear finished dimension Clear finished dimension Steel, ribbed, galvanised, powder coated and prime coated Steel, galvanised panel powder coated and prime coated Steel, horizontally ribbed, galvanised powder coated and prime coated Steel, galvanised Wood filling panel (Georgian/ Norway spruce cassette) powder coated and prime coated 6 Subject to technical changes.

5 Up-and-over garage door DF Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Up-and-over garage door DF single-leaf element.type of handing: Behind the opening. Door leaf filled with vertically ribbed galvanized sheet steel. Powder coated, similar to RAL 9016 (Traffic white). Corner frame with L-shaped profile at the side and Z-shaped profile at the top. With galvanized lower threshold profile 40 x 3. 6 wall anchor plugs on each side. Multiple spring system, plastic support. Door fittings: Springloaded special lock with downward locking profile half cylinder, black plastic round handle with pull cord. 2 rollers, rubber coated. Teckentrup DF or equivalent. Unit price Total price Technical data Product: Up-and-over garage door DF Installation in: Masonry Concrete Dimensions: Width: max mm or 5000 mm Height: max mm, depending on the door width (see price list table) Handing: Pre-assembled up-and-over garage door for handing behind or in the opening. Door leaf: Door leaf frame: 4-sided galvanized special hollow profile 75 x 36 x 2 mm Reinforcement: 2 reinforcements, 2.5 mm thick Ribbed door: galvanized sheet steel, vertically ribbed, optionally horizontally ribbed or infill provided by the customer Panelled door (Georgian/cassette) made of galvanized thin sheet. Panelled door: galvanized sheet steel, 1 mm thick. Wooden door: vertical Norway spruce, optionally horizontal or fishbone, door leaf frame without plinth Door leaf thickness: Frame: Surface: Special equipment: filling - steel panels with ventilation openings, corrugated grille, horizontal spruce panels, wooden fishbone panels with mullion 75 mm Corner frame with L-shaped profile at the side and Z-shaped profile at the top. With galvanized lower threshold bracket 40 x 3. 6 wall anchor plugs on each side and 3 x at the top. 3 threshold anchors. Special equipment: U-shaped frame (block frame) Ribbed/Panelled door: powder coated Traffic white, similar to RAL 9016 Panelled door (Georgian/cassette) woodgrain, powder coated Traffic white, similar to RAL 9016 Special coating for ribbed and panelled doors: trend colours RAL of your choice (Avoid dark colours for doors subject to direct sunlight, since cracks and warpage of the door leaf cannot be completely prevented. Pearleffect, fluorescent and metallic colours are only possible after individual clarification.) Fittings: Special equipment: Standard sizes: Ordering dimensions Modular dimensions 4000 x x x Wooden door: vertical Norway spruce, optionally horizontal or fishbone. Door leaf frame without plinth, powder coated Sepia brown (RAL 8014). The wood has been factory protected against fungal decay, decay and wood pests with a colourless impregnating solution. Final treatment is carried out by the customer with a final protective coat. 1 downward locking special lock 1 profile half cylinder mm Plastic round handle, black 1 pull cord 2 rollers, rubber coated Wicket door (outward opening), specify type of handing Garage door drive, radio control with hand-held transmitter and key holder Lock set for vertical locking mechanism with electric drive (vertical locking mechanism for version with wicket door Vertical bars Installation behind the opening L-shaped frame clear opening dimensions 3700 x x x U-shaped frame clear opening dimensions 3700 x x x x x x x 1920 Installation in the opening U-shaped frame clear opening dimensions 3580 x x x x x x x 1880 Special sizes: from 3000 x 2375 mm to 3750 x 2750 mm or 5000 x 2250 mm Subject to technical changes. 7

6 Up-and-over garage door DF Anchor distances FFL Side view in half opened position For widths greater than 4 mm two additional anchors at the top and bottom Behind the opening L-shaped frame Behind the opening U-shaped frame In the opening U-shaped frame Clear finished dimension Overall frame dimension Clear finished dimension Overall frame dimension Overall frame dimension Clear finished dimension Overall frame dimension Clear finished dimension FFL Overall frame dimension Clear finished dimension FFL Clear finished dimension Overall frame dimension FFL Anchor assembly Plug assembly Anchor assembly Plug assembly Anchor assembly Plug assembly Steel, ribbed, galvanised, powder coated and prime coated Steel, galvanised panel powder coated and prime coated Steel, horizontally ribbed, galvanised powder coated and prime coated Steel, galvanised Wood filling panel (Georgian/ Norway spruce cassette) powder coated and prime coated 8 Subject to technical changes.

7 left/right handed Single-skinned garage door ew-1 Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Single-skinned garage door ew-1. Single-leaf element which can used left/right handed. Out-side type of handing. Door leaf made of gal-vanized hollow profiles, 50 mm thick, 4-sided, with flange for holding the infill. Door leaf with vertically ribbed steel sheet panels and galvanized and powder coated corner frame, similar to RAL 9016 (Traffic white). Corner frame, 4-sided. Special lock with latch lever, prepared for profile cylinder. Black round handle set. 2 two-piece special hinges ew-1 or comparable. Unit price Total price Technical data Product: garage door ew-1 Installation in: Masonry Concrete Dimensions: modular dimension-width: mm modular dimension-height: mm Handing: Single leaf garage side door. Door can be used DIN left or DIN right, inward and outward opening. Fittings: Special hinges due to re-screwing of the hinges, optionally inward or outward opening. Special lock prepared for profile cylinder with latch lever, can be used left/right, black round handle set (plastic) Special equipment: Profile cylinder (same closing as the up-andover door type) mm Door leaf: Door leaf thickness: Frame: Surface: Leaf frame made of special hollow profiles 50 mm thick with flange for holding the infills. Two rear reinforcement elements. Door leaf filled with vertically ribbed galvanized sheet steel, optionally horizontally ribbed sheet steel, cassette Wooden filling - type of wood: vertically arranged Norway spruce, optionally horizontal or diagonal, door leaf frame without plinth Special equipment filling: corrugated grille, perforated sheet Ø10x14 50 mm Corner frame 1.5 mm thick galvanized and powder coated similar to RAL 9016 (Traffic white), with seal. With three welded-on wall anchor plugs on each side. Special equipment: block frame Door leaf frame/door leaf filling powder coated similar to RAL 9016 (Traffic white), Other RAL colours at an additional charge. Door leaf filled with panels with woodgrain design surface. Ordering dimensions (modular dimensions) 875 x x Standard sizes: Special sizes: Clear passage size with buffer without buffer 809 x x up to 1250 x 2375 mm 809 x x Subject to technical changes. 9

8 Single-skinned garage door ew-1 Two-piece hinge Clear passage size Clear passage size Clear passage size Two-piece hinge FFL FFL Outer buffer Inner buffer modular dimension height -55 mm Without bottom buffer dimension height -30 mm Clear passage size DIN left shown, DIN right laterally reversed Block frame Plug assembly Version 1 Plug assembly Version 2 Wall anchor assembly Door leaf versions Steel vertically ribbed Steel panels Steel horizont ally ribbed Steel panel (Georgian/cassette) Wood filling: Norway spruce vertical, Norway spruce horizontal, Norway spruce diagonal 10 Subject to technical changes.

9 Single-skinned garage door ew-2 Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Single-skinned garage door ew-2. Double-leaf element. type of handing. Door leaf frame made of special hollow profiles 50 mm thick with flange for holding the infill. Two rear reinforcement elements. Door leaf with vertically ribbed sheet steel panels and galvanized and powder coated corner frame, similar to RAL 9016 (Traffic white). Corner frame, 4-sided. Special lock with latch lever, prepared for profile cylinder. Black round handle set (plastic). 4 two-piece special hinges ew-2 or equivalent. Unit price Total price Technical data Product: Installation in: Dimensions: Handing: Garage door ew-2 Masonry Concrete modular dimension-width: mm modular dimension-height: mm DIN left outside/inside DIN right outside/inside Fittings: 4 special hinges Special lock prepared for profile cylinder with latch lever, can be used left/right, black round handle set, (plastic) With 2 door leaf fixing devices at the header and two security bolts on each side Special equipment: Profile cylinder (same closing as the up-and-over door type) mm Door leaf: Door leaf thickness: Frame: Surface: Leaf frame made of special hollow profiles 50 mm thick with flange for holding the infill. Two rear reinforcement elements. Door leaf filled with vertically ribbed galvanized sheet steel, optionally horizontally ribbed, sheet steel Special equipment filling: corrugated grille, perforated sheet Ø10x14 50 mm Corner frame 2 mm thick, galvanized and powder coated similar to RAL 9016 (Traffic white), with seal. With three welded-on wall anchor plugs on each side. Special equipment: block frame Door leaf frame/door leaf filling powder coated similar to RAL 9016 (Traffic white). Other RAL colours at an additional charge. Door leaf filled with panels with woodgrain design surface. Standard sizes: Ordering dimensions (modular dimensions) 2000 x x x 2125 Special sizes: Clear passage size with buffer without buffer 1934 x x x x x x 2055 from 1350 x 1750 to 2500 x 2250 mm Subject to technical changes. 11

10 Single-skinned garage door ew-2 Twopiece hinge Twopiece hinge Clear opening Clear opening Clear opening FFL FFL Outer buffer Inner buffer modular dimension height -55 mm Without bottom buffer dimension height -30 mm Clear opening Active door leaf DIN left shown, active door leaf DIN right laterally reversed Block frame Plug assembly Version 1 Plug assembly Version 2 Wall anchor assembly Door leaf versions Steel vertically ribbed Steel panels Steel panel (Georgian/cassette) 12 Subject to technical changes.

11 Single-skinned garage door RP-1 Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Single-skinned steel door RP-1. Single-leaf element, outside handing. Door leaf frame made of RP tube (4-sided) with flange for holding the panels. Door leaf thickness 40 mm. Door leaf filled with ribbed sheet steel, galvanized. 3-sided angular frame, powder coated, similar to RAL 9016 (Traffic white). Mortice lock prepared for profile cylinder. Black plastic handle set, 2 twopiece special hinges. RP-1 or equivalent. Unit price Total price Technical data Product: Installation in: Garage door RP-1 Masonry Concrete Dimensions: width: mm height: mm Handing: Door leaf: Door leaf thickness: Frame: DIN left outside/inside DIN right outside/inside Door leaf frame made of RP tube or special tubing with flange for holding the infill. Door leaf filled with ribbed, smooth or embossed galvanized sheet steel. Special equipment: filling - embossed or smooth sheet steel panels or wooden filling 40 mm Corner frame 2 mm thick galvanized and powder coated similar to RAL 9016 (Traffic white) or similar to RAL 8014 (Sepia brown). With 3-sided seal. 3 wall anchor plugs on each side Special equipment: Block frame Fittings: With tubular frame-mortice lock, prepared for profile cylinder, round handle set with rose escutcheon. 2 two-piece KO hinges with ball bearings Special equipment: Profile cylinder mm Glazing Ventilation slats Corrugated grille filling Bars Mullions (to partition the fields) Galvanized door leaf frame and frame Adjustable hinges Special sizes: Ordering dimensions (modular dimensions) from 750 x 1750 to 1000 x 2000 to 1125 x 2250 to 1350 x 2500 Clear passage sizes with buffer without buffer from 680 x 1685 to 930 x 2000 to 1055 x 2185 to 1280 x 2435 from 680 x 1715 to 930 x 1965 to 1055 x 2215 to 1280 x 2465 Surface: Door leaf frame/door leaf filling powder coated similar to RAL 9016 (Traffic white) or RAL 8014 (Sepia brown). Other RAL colours at an additional charge. Subject to technical changes. 13

12 Single-skinned garage door RP-1 Twopiece hinge Clear opening Clear opening Clear opening Twopiece hinge FFL FFL FFL Outer buffer Inner buffer modular Inner buffer ventilation slats Clear opening DIN left shown, DIN right laterally reversed Plug assembly Wall anchor assembly in accordance with DIN Weld-on assembly Door leaf versions Ribbed door Wooden door Panel filling Ventilation slats Corrugated grille 14 Subject to technical changes.

13 Single-skinned garage door RP-2 Text example Compile and tender according to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Single-skinned steel door RP-2. Double-leaf element, outside handing. Active door leaf DIN right. Door leaf 40 mm thick, made of galvanized RP profiles (4-sided). Door leaf filled with ribbed sheet steel, galvanized. 3-sided angular frame, powder coated, similar to RAL 9016 (Traffic white). Active door leaf with mortice lock prepared for profile cylinder. Black plastic handle set. Inactive door leaf with sliding bolt on the opposite hinge side. 2 two-piece special hinges. RP-2 or equivalent. Unit price Total price Technical data Product: Installation in: Garage door RP-2 Masonry Concrete Dimensions: width: mm height: mm Handing: active door leaf DIN left outside/inside active door leaf DIN right outside/inside Special equipment: Profile cylinder mm Glazing Ventilation blind Corrugated grille filling Bars (as a yard gate) Mullions (to partition the fields) Galvanized door leaf frame and frame Door leaf: Door leaf frame made of RP tube or special tubing with flange for holding the infill. Door leaf filled with ribbed, smooth or embossed galvanized sheet steel. Special equipment: filling - sheet steel panels, corrugated grille or wooden filling Special sizes: Door leaf thickness: Frame: Surface: 40 mm Corner frame 2 mm thick galvanized and powder coated similar to RAL 9016 (Traffic white). With 3-sided seal. Door leaf frame/door leaf filling powder coated similar to RAL 9016 (Traffic white). Other RAL colours at an additional charge. Ordering dimensions (modular dimensions) from 1500 x 1750 to 2000 x to 2375 x to 2750 x to 3000 x Clear passage size with buffer without buffer from 1430 x 1685 to 1930 x to 2305 x to 2680 x to 2930 x from 1430 x 1715 to 1930 x to 2305 x to 2680 x to 2930 x Fittings: (Active door leaf) with tubular frame-mortice lock, prepared for profile cylinder, round handle set with rose escutcheon. Inactive door leaf with mounted sliding bolt, on the opposite hinge side (outer buffer - on the hinge side for inner buffer) 4 two-piece KO hinges with ball bearings up to a modular dimension height of 2500 mm. 6 two-piece KO hinges with ball bearings up to a modular dimension height of 2500 mm. Subject to technical changes. 15

14 Single-skinned garage door RP-2 Twopiece hinge Clear opening Clear opening Clear opening Twopiece hinge FFL FFL FFL Outer buffer Inner buffer modular Inner buffer ventilation slats Clear opening Active door leaf DIN left shown, Active door leaf DIN right laterally reversed Plug assembly Wall anchor assembly in accordance with DIN Weld-on assembly Door leaf versions Ribbed door Wooden door Panel filling Ventilation slats Corrugated grille 16 Subject to technical changes.

15 Sectional door GSW 40-S Double-skinned steel door panels 40 mm Text example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1 st June 2015 Position No. of pieces Item Garage sectional door GSW 40-S, door leaf consisting of double-skinned steel door panels, galvanized surface, PUR foam core. Building depth 40 mm, outside woodgrain, inside stucco design. Outer colour Traffic white similar to RAL 9016, inside galvanized with transparent protective film. Door sections with central seal and floor seal. Frame with lateral strips. All fittings made of galvanized steel, lateral guidance via maintenance-free, adjustable rollers. Weight compensation via multiple spring/double cable system, tension springs housed in a spring duct above the horizontal guide rails. CarTeck GSW 40-S or equivalent. Unit price Total price Technical data Product: Garage sectional door GSW 40-S Heat insulation U-value: 0.56 W/m²k (40 mm panel) 0.95 W/m²k (only door leaf) 1.48 W/m²k (complete door, door surface 10 m²) Installation in: Masonry Concrete Autoclaved aerated concrete Wooden framework Dimensions: Type of handing: Door leaf: GSW 40-S: only standard sizes, see price list Behind the soffit Door leaf made of individual double-skinned door sections including central seal with the same partitioning, galvanized sheet steel. Finger pinch protection inside and outside in acc. with DIN EN Building depth of the sections 40 mm Insulation: Polyurethane foam core. Frame: Locking: Weight compensation: Surface Protection: Drive: Profile frame with header trim made of sendzimir galvanized sheet steel, EPDM strip with sealing lip at the sides and header trim. Coil-coated with polyester, prime coated Traffic white similar to RAL On request with automatic, double-sided engaging special lock. Round handle set and profile cylinder for manual operation. Handle at the bottom profile. Via a multiple tension spring/double cable system housed in a micro-profiled spring duct above the horizontal guide rail. Basic coat on door outer surface, double coat on the outside (polyester-based 25 µm). Galvanized steel parts, galvanized springs. Microprocessor-controlled drive, rail-guided, 230 V, 50 Hz Control: Impulse control with self- programming force limiter Soft start and stop Digital remote control Can be extended with other control units Centre ribbed: GSW 40-S Surface: Fittings: : woodgrain design, colour Traffic white similar to RAL Inside: stucco design, galvanized with transparent protective film. Bottom door edge: Frost-proof and rot-proof EPDM floor seal Standard version: Default without manual locking mechanism Prepared for emergency release (required if there is no other entry to the garage) Special version: With manual locking mechanism Subject to technical changes. 17

16 Sectional door GSW 40-S Double-skinned steel door panels 40 mm 120 mm Headroom Dimensions for 145 mm and 265 mm header versions on request 240 mm Headroom Standard with drive Standard for manual operation 120Header For the depth see table Building depth with drive For the depth see table Building depth without drive 240Header S S Ordering dimension = H = clear height inside Min. inner garage dimension = ordering dimension ,5 82, inside Ordering dimension = H = clear height * 240 mm Headroom = 150 mm in the round handle set (middle) *75 Ordering dimension = B = clear width section Frame 140 door leaf 27,5 40 frame 82,5 Please observe the following measurement details to guarantee exact assembly and precise and reliable operation of the CarTeck sectional door. B clear opening width (= ordering dimension) H clear height (= ordering dimension) Required Equipment: S headroom: Clear opening height: with drive 120 mm completely free Standard version Manual operation 240 mm - 25 mm Standard version Manual operation Manual operation with drive 120 mm 120 mm 240 mm mm -80mm completely free Special version Special version with door stopper (see accessories GSW doors) Special version with pack 125 mm extended top roller retainers (see accessories GSW doors) S The required headroom increases by + 25 mm for doors with reinforced roller retainers 18 Subject to technical changes.

17 Sectional door GSW 40-L Double-skinned steel door panels 40 mm optionally with glazing, optionally with wicket door Text example Compile and tender to requirements. Please refer to technical data below for respective details. Updated 1 st June 2015 Position No. of pieces Item Garage sectional door, door leaf consisting of individual double-skinned steel door panels, galvanized surface, PUR foam core. Building depth 40 mm, outer surface woodgrain, inner surface stucco design. Outer colour Traffic white similar to RAL 9016, inner colour Grey white similar to RAL Door sections with central seal and floor seal. Frame with lateral strips. All fittings made of galvanized steel, lateral guidance via maintenance-free, adjustable rollers. Weight compensation via multiple spring/double cable system, tension springs housed in a spring duct above the horizontal guide rails. CarTeck GSW 40-L or equivalent. Unit price Total price Technical data Product: Garage sectional door GSW 40-L Heat insulation U-value: 0.56 W/m²k (40 mm panel) 0.95 W/m²k (only door leaf) 1.48 W/m²k (complete door, door surface 10 m²) Installation in: Masonry Concrete Autoclaved aerated concrete Wooden framework Dimensions: width: mm height: mm Handing: Door leaf: Surface: Fittings: Wicket door: Frame: Behind the soffit Door leaf made of individual double-skinned door sections including central seal with the same partitioning, galvanized sheet steel, building depth of the sections 40 mm. Insulation: polyurethane foam core finger pinch protection inside and outside in accordance with DIN EN ribbed cassette unribbed centre ribbed Outer surface woodgrain design, stucco design, smooth or micro-profiled, Traffic white similar to RAL 9016 Inside stucco design, Grey white similar to RAL 9002 Bottom door edge: Frost-proof and rot-proof EPDM floor seal Standard version: Without manual locking mechanism Prepared for emergency release (required if there is no other entry to the garage) Special version: with manual locking mechanism (up to door width of 5000 mm). Enclosed in aluminium profiles E6/EV1 (the wicket door is always located in the middle), with low threshold 45 mm and full floor seal. The wicket door has a standard clearance width of 810 mm. All wicket doors include a top door closer, a profile cylinder pre-equipped lock with profile cylinder and aluminium handle set in E6/EV1. Profile frame made of sendzimir galvanized sheet steel, coil-coated with polyester, prime coated Traffic white similar to RAL 9016, Locking: Weight compensation: Surface protection: Drive: Glazing: optionally in trend and RAL colour at additional charge. EPDM strip with sealing lip at the sides. Header trim default in trend colour, RAL colour or similar to wood design. With manual locking mechanism (up to door width of 5000 mm). Via multiple tension spring/double cable system housed in a micro-profiled spring duct above the horizontal guide rail. Steel: coil-coated, double coat on the outside (polyester based 25 m) Wood designs: steel sections with UV-resistant, thermoplastic surface film in attractive designs. Single coat on the inside (polyester based 10 m). Galvanized steel parts, galvanized springs. Special equipment: additionally prime coated in trend colour or RAL of your choice. Pearl-effect, fluorescent and metallic colours are only possible after individual clarification. Microprocessor-controlled drive, rail-guided, 230 V, 50 Hz Control: impulse control with self-programming of the force limiter, soft start and stop Digital remote control, extendable with other control units Glazed strip or aluminium profiles, anodized, across the entire width of the door (separate section), plastic double glazing 20 mm, clear or crystal structure. Glazing strip with seals. Other colours or powder coating in accordance with RAL possible. Glazing for panelled, ribbed, centre ribbed, unribbed door (white polyurethane frame with wooden structure) in various versions (see dealer price list). Glazing: plastic double glazing 20 mm clear or crystal structure on the inside. Only possible for GSW 40-L unribbed / unribbed- smooth: Stainless steel round glazing Ø 305 mm. One pane of ESG glazing colourless and clear. Stainless steel filling plates. Type round glazing, plastic Ø 315 mm. Type Rectangular 3, white plastic glazing frame. Type 1/2 square, white polyurethane frame with smooth surface. Glazing: plastic double glazing 20 mm clear, structured or satin. Subject to technical changes. 19

18 Sectional door GSW 40-L Double-skinned steel door panels 40 mm optionally with glazing, optionally with wicket door 120 mm Headroom Dimensions for 145 mm and 265 mm header versions on request 240 mm Headroom Standard with drive Standard for manual operation 120Header For the depth see table Building depth with drive For the depth see table Building depth without drive 240Header S S Ordering dimension = H = clear height inside Min. inner garage dimension = ordering dimension ,5 82, inside Ordering dimension = H = clear height * 240 mm Headroom = 150 mm in the round handle set (middle) *75 Ordering dimension = B = clear width section Frame 140 door leaf frame 82.5 Please observe the following measurement details to guarantee exact assembly and precise and reliable operation of the CarTeck sectional door. B clear opening width (= ordering dimension) H clear height (= ordering dimension) Required Equipment: S headroom: Clear opening height: with drive 120 mm completely free Standard version Manual operation 240 mm - 25 mm Standard version Manual operation Manual operation with drive 120 mm 120 mm 240 mm mm -80mm completely free Special version Special version with door stopper (see accessories GSW doors) Special version with pack 125 mm extended top roller retainers (see accessories GSW doors) S The required headroom increases by + 25 mm for doors with reinforced roller retainers 20 Subject to technical changes.

19 Wooden frame construction Sectional door GSH Text example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1 st June 2015 Position No. of pieces Item Garage sectional door, consisting of separate door sections made of first choice wood, including central seal. Native spruce/fir with a natural look. With central seal and floor seal. Frame with lateral strips. All fittings made of galvanized steel, lateral guidance via maintenance-free, adjustable rollers. Weight compensation via multiple spring/double cable system, tension springs housed in a spring duct above the horizontal guide rails. CarTeck GSH or equivalent. Unit price Total price Technical data Product: Installation in: Garage sectional door GSH Masonry Concrete Autoclaved aerated concrete Wooden framework Dimensions: width: mm height: mm smaller dimensions on request Type of handing: Door leaf: Behind the soffit Consisting of separate door sections made of first choice wood, including central seal. Native spruce/fir and hemlock are processed with a natural look. Building depth of the sections is 40 mm. Frame: Weight compensation: Surface protection: Profile frame made of sendzimir galvanized sheet steel, coil-coated with polyester basic coating in Traffic white similar to RAL Optionally in trend and RAL colours at additional charge. EPDM strip with sealing lip at the sides and header trim. Via a multiple tension spring/double cable system housed in a micro-profiled spring duct above the horizontal guide rail. The wood has been factory protected against fungal decay, decay and wood pests with a colourless impregnating solution. The door leaf coated with colourless impregnating solution ex works must be treated with a final protective coat 2-3 weeks after installation. Or painted All steel parts and springs are galvanized ribbed cassette unribbed Drive: Microprocessor-controlled drive, rail-guided, 230 V, 50 Hz Control: impulse control with self-programming force limiter. Soft start and stop Digital remote control, extendable with other control units fishbone type 1 fishbone type 2 Bottom door edge: Frost-proof and rot-proof EPDM floor seal Fittings (Standard version): With special connecting console for rail-guided drives. We recommend rail-guided drives when operating GSH doors. The doors are not supplied as manually operated doors. Standard GSH doors are not supplied with apparatus for emergency release. All fittings made of galvanized steel Laterally adjustable rollers due to patented eccentric roller retainer, maintenance free. Subject to technical changes. 21

20 Wooden frame construction Sectional door GSH standard version Special version with pack 125 mm extended top roller retainers (see accessories GSW doors) 22 Subject to technical changes.

21 Side doors garage sectional door outer surfaces to match GSW 40-L Text example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1 st June 2015 Position No. of pieces Item Garage side door, matches garage sectional door GSW 40-L, door leaf frame and door frame made of extruded aluminium profiles (no thermal separation), building depth 53 mm, 3-sided double rabbet seal, sliding threshold seal. Door filling made of double-skinned steel door panels, outside woodgrain, inside stucco design, made of galvanized sheet steel, PU foam core. CarTeck side door type GSW 40-L or equivalent. Unit price Total price Technical data Product: Side doors for GSW 40-L Installation in: Masonry Concrete Autoclaved aerated concrete Steel construction Wooden framework Dimensions: width: mm single-leaf height: mm other sizes available on request Dimensions: width: mm double-leaf height: mm other sizes available on request Type of handing: Door leaf: Surface: Please always specify when ordering: - Behind the opening/inward opening - In the opening/inward opening - In the opening/outward opening Appearance matches CarTeck garage sectional door GSW 40-L, door leaf frame and frame made of extruded aluminium profiles (no thermal separation), building depth 53 mm, 3-sided double rabbet seal. Sliding threshold seal. Door filling made of doubleskinned steel panels, outside woodgrain, inside stucco design, made of galvanized sheet steel, PU foam core. Alignment of door panels, ribs/panels only possible with doors of the same height. - ribbed woodgrain stucco smooth micro-prof. - centre ribbed woodgrain stucco smooth micro-prof. - wood design smooth Outer surface woodgrain design woodgrain design Inside stucco design Seals: Frost-proof EPDM bottom sliding seal - cassette woodgrain - wood design woodgrain - unribbed woodgrain stucco smooth micro-prof. Door frame: Fittings and locks: Surface protection: Glazing: Made of extruded aluminium profiles, mitred at the top on both sides. Building depth 53 mm, bottom threshold 4 mm (can be removed if required). Mortice lock with profile cylinder Plastic handle set, profile cylinder version Adjustable hinges Door filling: Door panels made of galvanized sheet steel with polyurethane basic coating on both sides. outside: - Standard Traffic white similar to RAL 9016, trend colours or RAL of your choice, similar to the RAL colour chart. Version GSW 40-L "Golden Oak", "Rosewood", "Winchester". Steel sections with UV-resistant, thermoplastic surface film in attracttive designs. inside: - Grey white, similar to RAL 9002 Safety notes: (Avoid dark colours for doors subject to direct sunlight, since cracks and warpage of the door leaf cannot be completely prevented). Not available in pearl-effect, fluorescent and metallic colours. Glazed strip or aluminium profiles, anodized, across the entire width of the door (separate section), plastic double glazing 20 mm, clear, opal or crystal structure. Glazing strip with seals. Other colours or powder coating in accordance with RAL possible. Glazing for cassette, ribbed, centre ribbed, unribbed door (white polyurethane frame with smooth surface) in various versions (see price list). Glazing: plastic double glazing 20 mm, clear, crystal structure or satin on the inside. Cassette Pure Only for GSW 40-L unribbed/unribbed-smooth Stainless steel round glazing Ø 305 mm. One pane of ESG glazing colourless and clear. Stainless steel filling plates. Type round glazing, plastic, Ø 315 mm. Type Rectangular 3, white plastic glazing frame Type 1/2 square, white polyurethane frame with wood structure Glazing: plastic double glazing 20 mm, clear, structured or satin. Subject to technical changes. 23

22 Side doors garage sectional door outer surfaces to match GSW 40-L Door height 2500 mm 2375 mm 2250 mm 2125 mm 2000 mm 1875 mm Height of Dimension X the sections (handle) 493 mm 469 mm 556 mm 523 mm 493 mm 469 mm 935 mm 1140 mm 1035 mm 985 mm 935 mm 1140 mm Installation behind the soffit only inward opening Structural opening mm = RAM Installation in the soffit inward and outward opening Structural opening - 10 mm = RAM Structural opening 40 mm = clear opening width Structural opening DIN left shown,, DIN right laterally reversed Structural opening 150 mm = clear opening width Structural opening Structural opening mm = RAM Structural opening - 10 mm = RAM Structural opening 40 mm = clear opening width Structural opening Active door leaf DIN left shown, Active door leaf DIN right laterally reversed Structural opening 150 mm = clear opening width Structural opening Installation behind the soffit only inward opening Note: Overall frame dimension (RAM) = Ordering dimension Installation in the soffit inward and outward opening Structural opening + 50 mm = RAM Structural opening 20 mm = clear opening width Structural opening Structural opening - 10 mm = RAM Structural opening 80 mm = clear opening width Structural opening 24 Subject to technical changes.

23 Side door garage sectional door GSH Text example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1 st June 2015 Position No. of pieces Item Garage side door, matches CarTeck garage sectional door GSH. Door leaf, filling and door frame made of Native spruce/fir, with waterproof bonding. Building depth 68 mm, 3-sided double rabbet seal and bottom threshold seal. Alignment of the door filling is only possible for a door of the same height. CarTeck side door GSH or equivalent. Unit price Total price Technical data Product: Installation in: Side door garage sectional door GSH Masonry Concrete Autoclaved aerated concrete Steel construction Ordering dimensions: width: mm height: mm Type of handing: Please always specify when ordering: - behind the opening/inward opening - in the opening/inward opening - in the opening/outward opening Surface protection: The wood has been factory protected against fungal decay, decay and wood pests with a colourless impregnating solution. Surface optionally coated with an open-porous paint or RAL of your choice. Optionally: basic coat of coloured paint (always adhere to the instructions regarding the required final treatment provided by the customer) Or final treatment Door leaf: Matches CarTeck garage sectional door GSH. Door leaf, filling and door frame made of Native spruce/fir, hemlock, with waterproof bonding. Building depth 68 mm, 3-sided, double rabbet seal and bottom threshold seal. Alignment of the door filling to the door leaf is only possible for a door of the same height. ribbed cassette fishbone fishbone type 1 type 2 Bottom door edge: Frost-proof EPDM bottom threshold seal Fittings and closing devices: Mortice lock with profile cylinder Plastic handle set, profile cylinder version Adjustable hinges Subject to technical changes. 25

24 Side door garage sectional door GSH RAM = structural opening mm Structural opening (RRM) RAM = structural opening - 10 mm Clear opening = RRM 40 mm Clear opening = RRM 170 mm Structural opening (RRM) Note: Overall frame dimension (RAM) = Ordering dimension Overall frame dimension = Structural opening + 60 mm Clear opening = structural opening 42 mm Structural opening (RRM) Overall frame dimension = Structural opening - 10 mm Clear opening = structural opening 112 mm Structural opening (RRM) Installation behind the soffit Installation in the soffit 26 Subject to technical changes.

25 Garage door drives 12.2, 20.2, year guarantee Example Compile and tender according to requirements. Please refer to technical data below for respective details Updated 1 st June 2015 Position Quantity Item Unit price Garage door drive drive system 20.2 Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) Tensile and compressive force 1000 N Power consumption during stand-by < 2.5 W Operating speed up to 200 mm/sec Tested burglary resistance Including a manipulation-proof hand-held transmitter, 4-channel, 868 MHz (black) Integrated lighting Design depth of drive incl. rail Z1 = 3320 mm Manufacturer "CarTeck drive system 20.2" or similar. Total price Technical data The garage door drive should only be used for the automatic operation of spring balanced up-and-over garage doors and sectional doors in non-commercial outdoor areas. Product: Garage door drive drive system 12.2 Refer to latest price list for assignment table Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) *Tensile and compressive force 500 N Power consumption during stand-by < 2 W Operating speed up to 140 mm/sec Including a manipulation-proof 2-channel hand-held transmitter 868 MHz Integrated lighting Design depth of drive incl. rail Z1 = 3320 mm, 3170 mm at 90 rotated drive head Product: Garage door drive drive system 20.2 Refer to latest price list for assignment table Accessories: Emergency unlock kit o Emergency unlock kit for sectional doors o Emergency unlock kit for up-and-over doors Light barrier Indoor switch TI-I1, pulse Radio indoor switch TI-F2 Radio code switch, 868 MHz Key-operated switch (flush/surface mounted) Hand-held transmitter: o SH2-S 2-button hand-held transmitter, 868 MHz o SH4-D black/white 4 button hand-held transmitter, 868 MHz o Wall bracket for SH4-D remote control External 1-channel radio receiver with antenna Additional rail suspension Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) *Tensile and compressive force 1000 N Power consumption during stand-by < 2.5W Operating speed up to 200 mm/sec Including a manipulation-proof 4-channel hand-held transmitter, 868 MHz (black) Integrated lighting Design depth of drive incl. rail Z1 = 3320 mm, Z2 = 3570 mm * relates to spring-compensated door leaf weight Product: Garage door drive drive system 40.2 Refer to latest price list for assignment table Rated voltage 230 V (alternating current) Control voltage 24 V (direct current) *Tensile and compressive force 1500 N Power consumption during stand-by <2.5W Operating speed up to 200 mm/sec Including a manipulation-proof 4-channel hand-held transmitter, 868 MHz (black) Integrated lighting Design depth of drive incl. rail Z1 = 3320 mm, Z2 = 3570 mm, Z3 = 4070 mm Subject to technical changes. 27