K Series. Next-Generation Right-Angle Shaft Geared Motors. Compact Standard AC Motors

Transcription

1 Compact Standard C Motors K Series Induction Motors Hypoid Right-ngle Hollow Shaft JH Gear Hypoid Right-ngle Solid Shaft JL Gear 4 W 6 W 9 W Highly Efficient, Strong Next-Generation Right-ngle Shaft Geared Motors

2 Hypoid Right-ngle Shaft Gear High Performance Motor Installed The motor and gearhead already pre-assembled prior to delivery. The lead wire outlet can be changed either direction by rotating the motor position 9. Hypoid Right-ngle Shaft Gear = Motor Hypoid Right-ngle Shaft Gear Designed specifically for each voltage to optimize the magnetic balance of the motor. The motors comply with China National Standard of Energy Efficiency Grade 1. The efficiency has been drastically improved, motor heat and vibration have been reduced to improved reliability and reduced power consumption of devices. Comparison with conventional model Efficiency Heat generation Vibration Parallel Key Up to 2.7% increase Up to 5.3 C reduction Up to 5% reduction Power Consumption [W] 1 5 Power Consumption Reduced by max. 3.2 W K Series 4 W Conventional model 4 W For 4 W output with Single-Phase 22 VC 5 Hz at rated output Energy Efficiency Regulation in China (only models with Single-Phase 22/23 VC 5 Hz) Conforms to the First Grade (G ) 2 Obtained a third-party certification based on China energy-saving product certification system (CQC ).

3 est Combination of High Performance Small Motor and High Strength Right-ngle Shaft Gearhead High Strength Right-ngle Shaft Gearhead High Permissible Torque The rated torque has increased a maximum of 2.7 times compare to conventional models. Rated Torque of 9 W Hypoid Right-ngle Shaft Gear High-precision hypoid gears have been employed. The gearheads offer large increased torque and decreased noise compared with conventional models. The radial and axial loads at the gearhead output shaft have also largely increased, contributing to downsizing and improved reliability of devices. Rated Torque [N m] High Strength Rated torque increased by 2.7 times Conventional model K Series Expanded variation of high gear ratio lineup K Series Rated torque 53.9N m Conventional model 5GE-R Rated torque 2N m The permissible radial load increased 2.3 times and the permissible axial load increased 1.3 times compared with conventional models. K Series 9 W Permissible radial load Conventional model 5GE-R Permissible radial load Permissible axial load Permissible radial load 1174 N 1 mm from the output shaft end Permissible axial load 343 N Permissible axial load Permissible radial load 5 N Permissible axial load 25 N For Right-ngle Solid Shaft Gearheads 3

4 dvantages of Hypoid Right-ngle Shaft Gears Saving the Space and Cost Devices Space Saving Space saving by placing the motor to the right angle position against the load shaft. Cost Saving The hollow shaft type reduces parts cost and simplifies assembling steps by reducing fastening parts. 18 mm Hypoid Right-ngle Shaft Gear Shortened by 92 mm 2 mm With Conventional Parallel Shaft Gearhead Reduced parts cost Simplified assembling Reduced connecting space [Hollow Shaft Gearhead] Parts reduction [Parallel Shaft Gearhead] Reduced connecting space Increased ssembling Flexibility Horizontal Symmetrical Structure The output shaft of the gearhead is located in the middle of the installation surface vertically. The motor fits on conveyors or any devices without changing the installation hole position regardless of the horizontal installation direction. Selectable Lead Wire Outlet Position The basic outlet position of the lead wire is facing a downstream direction viewed from. For a lead wire outlet position other than, please specify when ordering. Lineup Wire Type Hypoid Right-ngle Hollow Shaft JH Gear Hypoid Right-ngle Solid Shaft JL Gear Lead Wire Output Power Power Supply Voltage Gearhead Ratio W Single-Phase 11/115 VC 6 W 6 Hz Single-Phase 9 W 22/23 VC 5/6 Hz 4

5 System Configuration Not supplied. K Series Hypoid Right-ngle Shaft Gear Peripheral Equipment (Sold Separately) rake Pack S5W Capacitor (Included) Capacitor Cap (Included) Programmable Controller C Power Supply (Main power supply) 24 VDC Power Supply (For signals) ccessories (Sold Separately) Flexible Couplings Page 16 These motors can be used for the solid shaft type. System Configuration Example Induction Motor with Hypoid Right-ngle Solid Shaft JL Gear 5IK4KG-5L1 Sold Separately Flexible Couplings MCL The system configuration shown above is an example. Other combinations are available. Product Number Code Hypoid Right-ngle Shaft Gear 5 I K 9 K G - 5 H Motor Gearhead Motor Gearhead 1 Motor Frame Size 5: 9 mm 2 Motor Type I: Induction Motor 3 Series Name K: K Series 4 Output Power (W) (Example) 9: 9 W 5 Shaft Configuration K: Round Shaft Type With key 6 Power Supply Voltage F: Single-Phase 11/115 VC 6 Hz G: Single-Phase 22/23 VC 5 Hz R: Single-Phase 22/23 VC 6 Hz 7 Combination Type Motor 5: 9 mm 8 Type H: Hypoid Right-ngle Hollow Shaft JH Gear L: Hypoid Right-ngle Solid Shaft JL Gear 9 1 Identification Part Number 5

6 Induction Motors 4 W 9 mm K Series Hypoid Right-ngle Shaft Gear Hypoid Right-ngle Hollow Shaft JH Gear Hypoid Right-ngle Solid Shaft JL Gear Specifications Continuous Rating Lead Wire Type Output Power Voltage Frequency Current Capacitor Overheat Protection Device Hollow Shaft Type Solid Shaft Type W VC Hz μf 5IK4KF-5H 5IK4KF-5L Single-Phase Single-Phase TP 5IK4KG-5H 5IK4KG-5L 4 Single-Phase Single-Phase TP 5IK4KR-5H 5IK4KR-5L Single-Phase Single-Phase TP Hz Speed [r/min] 6 Hz Rated Torque [N m] Starting Torque [N m] Permissible Load Inertia J [ 1-4 kg m 2 ] Permissible [N] Single-Phase 11/115 VC 6 Hz Single-Phase 22/23 VC 6 Hz Single-Phase 22 VC 5 Hz Single-Phase 23 VC 5 Hz Single-Phase 11/115 VC 6 Hz Single-Phase 22/23 VC 6 Hz Single-Phase 22 VC 5 Hz Single-Phase 23 VC 5 Hz t Instantaneous Stop Hollow 1 mm from installation surface Shaft 2 mm from installation surface Solid Shaft 1 mm from output shaft end mm from output shaft end Permissible xial Load [N] The radial load at each distance can also be calculated with a formula Page 15 TP: This indicates that there is a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. e sure to turn the power supply off before inspecting. The speed is calculated by dividing the motor's synchronous speed (5 Hz: 15 r/min, 6 Hz: 18 r/min) by the gear ratio. The actual speed is up to 3% less depending on the load. bout Load Position Hollow Shaft xial Load Solid Shaft xial Load 1 mm 2 mm Distance from installation surface 1 mm 2 mm Distance from output shaft end Product Line Hypoid Right-ngle Hollow Shaft JH Gear 5IK4KF-5H 5IK4KG-5H 5IK4KR-5H 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 The following items are included in each product. Motor, Gearhead, Capacitor, Capacitor cap, Installation screws, Parallel key (Stainless steel), Safety cover, Operating manual Hypoid Right-ngle Solid Shaft JL Gear 5IK4KF-5L 5IK4KG-5L 5IK4KR-5L 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 The following items are included in each product. Motor, Gearhead, Capacitor, Capacitor cap, Installation screws, Parallel key (Iron), Operating manual number in the box in the product name indicates the gear ratio. 6

7 Dimensions (Unit = mm) "Mounting screws" are included. Dimensions of installation screws Page capacitor is included. Dimensions for capacitor Page number in the box in the product name indicates the gear ratio. Lead Wire Type Hypoid Right-ngle Hollow Shaft JH Gear Motor Gearhead Mass kg 2D CD 5IK4KF-5H 5IK4KF 5IK4KG-5H 5IK4KG 5H IK4KR-5H 5IK4KR 15 (261.5) Safety Cover (Included) Parallel Key (Included) 17.3 Protective Earth Terminal M4 ϕ89 98 ϕ31 ϕ Motor Leads 3 mm UL Style 3271, WG (15) Detail Drawing of Protective Earth Terminal 5 max. ϕ ϕ24 ϕ ϕ (H8) ϕ ϕ (H8) ϕ ϕ24 ϕ 4 M1 4 ϕ8.6 4 M (38) 4 ϕ1.5 Cross Section - Cross Section - Hypoid Right-ngle Solid Shaft JL Gear Motor Gearhead Mass kg 2D CD 5IK4KF-5L 5IK4KF 5IK4KG-5L 5IK4KG 5L IK4KR-5L 5IK4KR (261.5) ϕ18.18(h7) 31± ± Parallel Key (Included) Protective Earth Terminal M ϕ Motor Leads 3 mm UL Style 3271, WG (15) Detail Drawing of Protective Earth Terminal 4 M1 4 ϕ (31) 3± max. 4 M1 4 ϕ (38) Cross Section - Details of t the time of shipment, the parallel key is fixed in the key slot of the gearhead shaft. 7

8 Induction Motors 6 9 mm K Series Hypoid Right-ngle Shaft Gear Hypoid Right-ngle Hollow Shaft JH Gear Hypoid Right-ngle Solid Shaft JL Gear Specifications Continuous Rating Lead Wire Type Output Power Voltage Frequency Current Capacitor Overheat Protection Device Hollow Shaft Type Solid Shaft Type W VC Hz μf 5IK6KF-5H 5IK6KF-5L Single-Phase Single-Phase TP 5IK6KG-5H 5IK6KG-5L 6 Single-Phase Single-Phase TP 5IK6KR-5H 5IK6KR-5L Single-Phase Single-Phase TP Speed [r/min] 5 Hz Hz Single-Phase 11/115 VC 6 Hz Rated Torque [N m] Single-Phase 22/23 VC 6 Hz Single-Phase 22/23 VC 5 Hz Starting Torque [N m] Single-Phase 22 VC 5 Hz Permissible Load Inertia J [ 1-4 kg m 2 ] Permissible [N] t Instantaneous Stop Hollow 1 mm from installation surface Shaft 2 mm from installation surface Solid Shaft 1 mm from output shaft end mm from output shaft end Permissible xial Load [N] The radial load at each distance can also be calculated with a formula Page 15 TP: This indicates that there is a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. e sure to turn the power supply off before inspecting. The speed is calculated by dividing the motor's synchronous speed (5 Hz: 15 r/min, 6 Hz: 18 r/min) by the gear ratio. The actual speed is up to 3% less depending on the load. bout Load Position Hollow Shaft xial Load Solid Shaft xial Load 1 mm 2 mm Distance from installation surface 1 mm 2 mm Distance from output shaft end Product Line Hypoid Right-ngle Hollow Shaft JH Gear 5IK6KF-5H 5IK6KG-5H 5IK6KR-5H 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 The following items are included in each product. Motor, Gearhead, Capacitor, Capacitor cap, Installation screws, Parallel key (Stainless steel), Safety cover, Operating manual Hypoid Right-ngle Solid Shaft JL Gear 5IK6KF-5L 5IK6KG-5L 5IK6KR-5L 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 The following items are included in each product. Motor, Gearhead, Capacitor, Capacitor cap, Installation screws, Parallel key (Iron), Operating manual number in the box in the product name indicates the gear ratio. 8

9 Dimensions (Unit = mm) "Mounting screws" are included. Dimensions of installation screws Page capacitor is included. Dimensions for capacitor Page number in the box in the product name indicates the gear ratio. Lead Wire Type Hypoid Right-ngle Hollow Shaft JH Gear Dimensions No. Motor Gearhead Mass kg 2D CD 5IK6KF-5H 5IK6KF IK6KR-5H 5IK6KR 5H 2 5IK6KG-5H 5IK6KG Dimensions 1 12 (276.5) Safety Cover (Included) Parallel Key (Included) Protective Earth Terminal M ϕ31 ϕ max. 3 Motor Leads 3 mm UL Style 3271, WG ϕ ϕ15 (H8) ϕ ϕ15 (H8) +.11 ϕ M1 4 ϕ8.6 4 M (38) 21.5 (12) Detail Drawing of Protective Earth Terminal ϕ ϕ24 ϕ24 ϕ 4 ϕ1.5 Cross Section - Cross Section - Dimensions 2 (276.5) Safety Cover (Included) Parallel Key (Included) 17.3 Protective Earth Terminal M4 ϕ89 98 ϕ31 ϕ Motor Leads 3 mm UL Style 3271, WG (12) Detail Drawing of Protective Earth Terminal 5 max. ϕ ϕ24 ϕ ϕ (H8) ϕ ϕ (H8) ϕ ϕ24 ϕ 4 M1 4 ϕ8.6 4 M (38) 4 ϕ1.5 Cross Section - Cross Section - 9

10 Hypoid Right-ngle Solid Shaft JL Gear Dimensions No. Motor Gearhead Mass kg 2D CD 5IK6KF-5L 5IK6KF IK6KR-5L 5IK6KR 5L 2 5IK6KG-5L 5IK6KG Dimensions 1 (276.5) ϕ18.18(h7) 31± ± Parallel Key (Included) Protective Earth Terminal M Motor Leads 3 mm UL Style 3271, WG (12) Detail Drawing of Protective Earth Terminal 5 max. 4 M1 4 ϕ8.6 4 M1 4 ϕ (38) Cross Section - (31) 3±.5 27 Details of Dimensions 2 (276.5) ϕ18.18(h7) 31± ± Parallel Key (Included) Protective Earth Terminal M ϕ Motor Leads 3 mm UL Style 3271, WG (12) Detail Drawing of Protective Earth Terminal 4 M1 4 ϕ (31) 3± max. 4 M1 4 ϕ (38) Cross Section - Details of t the time of shipment, the parallel key is fixed in the key slot of the gearhead shaft. 1

11 Induction Motors 9 9 mm K Series Hypoid Right-ngle Shaft Gear Hypoid Right-ngle Hollow Shaft JH Gear Hypoid Right-ngle Solid Shaft JL Gear Specifications Continuous Rating Lead Wire Type Output Power Voltage Frequency Current Capacitor Overheat Protection Device Hollow Shaft Type Solid Shaft Type W VC Hz μf 5IK9KF-5H 5IK9KF-5L Single-Phase Single-Phase TP 5IK9KG-5H 5IK9KG-5L 9 Single-Phase Single-Phase TP 5IK9KR-5H 5IK9KR-5L Single-Phase Single-Phase TP Speed [r/min] 5 Hz Hz Rated Torque [N m] Single-Phase 11/115 VC 6 Hz Single-Phase 22/23 VC Starting Torque [N m] Permissible Load Inertia J [ 1-4 kg m 2 ] Permissible [N] Single-Phase 11/115 VC 6 Hz Single-Phase 22/23 VC 6 Hz Single-Phase 22 VC 5 Hz Single-Phase 23 VC 5 Hz t Instantaneous Stop Hollow 1 mm from installation surface Shaft 2 mm from installation surface Solid Shaft 1 mm from output shaft end mm from output shaft end Permissible xial Load [N] The radial load at each distance can also be calculated with a formula Page 15 TP: This indicates that there is a built-in thermal protector (automatic return type). If a motor overheats for any reason, the thermal protector is activated and the motor is stopped. When the motor temperature drops, the thermal protector closes and the motor restarts automatically. e sure to turn the power supply off before inspecting. The speed is calculated by dividing the motor's synchronous speed (5 Hz: 15 r/min, 6 Hz: 18 r/min) by the gear ratio. The actual speed is up to 3% less depending on the load. bout Load Position Hollow Shaft xial Load Solid Shaft xial Load 1 mm 2 mm Distance from installation surface 1 mm 2 mm Distance from output shaft end Product Line Hypoid Right-ngle Hollow Shaft JH Gear 5IK9KF-5H 5IK9KG-5H 5IK9KR-5H 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 The following items are included in each product. Motor, Gearhead, Capacitor, Capacitor cap, Installation screws, Parallel key (Stainless steel), Safety cover, Operating manual Hypoid Right-ngle Solid Shaft JL Gear 5IK9KF-5L 5IK9KG-5L 5IK9KR-5L 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 1, 15 2, 25, 3 4, 5, 6 8, 1, 12 16, 2, 24 The following items are included in each product. Motor, Gearhead, Capacitor, Capacitor cap, Installation screws, Parallel key (Iron), Operating manual number in the box in the product name indicates the gear ratio. 11

12 Dimensions (Unit = mm) "Mounting screws" are included. Dimensions of installation screws Page capacitor is included. Dimensions for capacitor Page number in the box in the product name indicates the gear ratio. Lead Wire Type Hypoid Right-ngle Hollow Shaft JH Gear Motor Gearhead Mass kg 2D CD 5IK9KF-5H 5IK9KF 5IK9KG-5H 5IK9KG 5H IK9KR-5H 5IK9KR 5 (291.5) Safety Cover 48 (Included) Parallel Key (Included) ϕ31 ϕ31 Protective Earth Terminal M Motor Leads 3 mm UL Style 3271, WG (5) Detail Drawing of Protective Earth Terminal 5 max ϕ ϕ15 (H8) ϕ ϕ15 (H8) +.11 ϕ M1 4 ϕ8.6 4 M1 38 ϕ ϕ24 ϕ24 ϕ 25 (38) 4 ϕ1.5 Cross Section - Cross Section - Hypoid Right-ngle Solid Shaft JL Gear Motor Gearhead Mass kg 2D CD 5IK9KF-5L 5IK9KF 5IK9KG-5L 5IK9KG 5L IK9KR-5L 5IK9KR (291.5) ± ϕ18.18(h7) 48 27± Parallel Key (Included) Protective Earth Terminal M Motor Leads 3 mm UL Style 3271, WG (5) Detail Drawing of Protective Earth Terminal 4 M1 4 ϕ (31) 3± max. t the time of shipment, the parallel key is fixed in the key slot of the gearhead shaft. 4 M1 4 ϕ (38) Cross Section - Details of 12

13 Dimensions of Capacitor (Included) ϕ Series ϕ Series Dimensions No C Dimensions No C 6 (.5) R1 6 (.5) 5IK4KF-5H 5IK4KF-5L 5IK4KG-5H 5IK4KG-5L 5IK4KR-5H 5IK4KR-5L 5IK6KF-5H 5IK6KF-5L 5IK6KG-5H 5IK6KG-5L 5IK6KR-5H 5IK6KR-5L 5IK9KF-5H 5IK9KF-5L 5IK9KG-5H 5IK9KG-5L 5IK9KR-5H 5IK9KR-5L Capacitor C Mass g CH9CFUL CH25FUL CH2FUL CH16CFUL CH4FUL CH4FUL CH2CFUL CH6FUL CH5FUL capacitor cap is included with the capacitor. number in the box in the product name indicates the gear ratio. Unit: mm Dimensions No. 1 2 Dimensions of Installation Screws Product Hexagonal Socket Head Screw Name Nominal L1 (mm) L2 (mm) 5IK M Installation screws: 4 plain washers and 4 spring washers are included. The installation screw material is stainless steel. L2 L1 General Specifications Item Insulation Resistance Dielectric Strength Voltage Temperature Rise Heat-resistant Class Overheat Protection Device Operating mbient Temperature Operating mbient Humidity Degree of Protection Specifications The measured value is 1 MΩ or more when a 5 VDC megger is applied between the motor windings and the case after continuous operation under normal ambient temperature and humidity. No abnormality is judged even with application of 1.5 kvc at 5 Hz or 6 Hz between the motor windings and the case for 1 minute after continuous operation under normal ambient temperature and humidity. Temperature rise of windings are 8 C or less measured by the resistance method after continuous operation under normal ambient temperature and humidity. () uilt-in thermal protector (utomatic return type) Open: ±5 C Close: 85±2 C +4 C (Non-freezing) 85% or less (Non-condensing) IP2

14 Connection Diagrams The motor rotation direction varies by gear ratio. Check the gear ratio of the gearhead to be used before connecting. 1 6 CW CCW 8 24 CCW CW CCW CCW Connection Diagrams Earth N Power Supply L lack Red White CW Earth N Power Supply L lack Red White CW Capacitor Capacitor With Hollow Shafts The motor rotation direction varies by installation surface. CCW CW Screw View from surface : Rotates in reverse direction. Note Change the direction of motor rotation only after bringing the motor to a stop. If an attempt is made to change the direction of rotation while the motor is rotating, the motor may ignore the reversing command or change its direction of rotation after some delay. How to Connect a Capacitor The capacitor has four terminals. s shown in the figure, the terminal is internally connected with the terminal, and the terminal C with the terminal D. Electrically, these are handled as two terminals. C D Inner Wiring Diagram for 4-Terminal Capacitor 14

15 Installing a Hollow Shaft Load Example of Load Shaft Installation Method The load installation method differs depending on the shape of the load shaft. See the figures below. The hollow output shaft is processed to a tolerance of the inner diameter H8, and incorporates a key slot for load shaft installation. The recommended tolerance of the load shaft is h7. The load shaft can be attached to the output shaft from either left or right end in the following figure below. Note To prevent sticking, apply a coat of grease on the exterior surface of the load shaft and interior surface of the hollow output shaft. Stepped Load Shaft Fixing Method Using the End Plate Load Shaft Key Hollow Output Shaft Screw Fixing Method Using the Retaining Ring for Hole Load Shaft Key Hollow Output Shaft Spacer Plain Washer Screw Spring Washer End Plate Spring Washer Retaining Ring for Hole For Non-Stepped Load Shaft Load Shaft Key Hollow Output Shaft Spacer Plain Washer Screw Spring Washer Retaining Ring for Hole Spacer Recommended Load Shaft Installation Method Inner Diameter of Hollow Output Shaft (H8) ϕ Recommended Tolerance of Load Shaft (h7) ϕ15.18 Unit: mm Screw Size M6 Stepped Shaft La Length 72 Outer Diameter ϕ14.5 Spacer Dimensions Inner Diameter ϕ7 Width 3 Nominal Hole Diameter of Retaining Ring ϕ15 C Type Retaining Ring End Plate Thickness 3 Retaining rings for holes, spacers, screws or other parts used to install the load shaft are not supplied. Length of Load Shaft Same or more than La Inner diameter tolerance H8 part It is recommended that 5 mm or more of the load shaft goes into the inner diameter tolerance H8 part. Permissible Calculation of the Hollow Shaft Type Formulas to calculate permissible radial loads vary depending on the mechanism. When One End of the Load Shaft is Not Supported by a earing Unit 69 Permissible W N = F 59+Lp Load Point Lp When One End of the Load Shaft is Not Supported by a earing Unit Load Point Permissible W N = 69 S+4 F 65 S-Lp S Lp F N : Permissible radial load when the reference point is at 1 mm from the flange-installation surface. Lp mm : Distance from the flange-installation surface to the load point. S mm : Distance from the flange-installation surface to the bearing unit. For permissible radial load at 1 mm from the flange-installation surface, see the specification table for each output. Page 6, Page 8, Page 11 15

16 ccessories (Sold Separately) Flexible Couplings This clamping type coupling connects the gearhead shaft and the mating shaft. Product Line Coupling Type MCL55 MCL65 During Shock Load Uniform Load Shock Load pplicable Products 5IK4K -5L 5IK6K -5L 5IK9K -5L Hypoid Right-ngle Solid Shaft F, G or R indicating the power voltage is entered where the box is located within the product name. number in the box in the product name indicates the gear ratio. Safety Precautions To ensure correct operation, carefully read the Operating Manual before using it. The products listed in this catalogue are for industrial use and for built-in component. Do not use for any other applications. The factories which manufacture the products listed in this catalogue have obtained Quality Management Systems ISO91 and Environment Management Systems ISO141. The content listed in this catalogue such as performance and specifications of the products are subject to change without notice for improvements. The price of all products listed in this catalogue does not include the consumption tax etc. For details of the products, please contact the nearest dealer, sales office or the following Order Support Center or Customer Support Center. is registered trademark or trademark of Oriental Motor in Japan and other countries. ORIENTL MOTOR SI PCIFIC PTE. LTD. 31 Kaki ukit Road 3, #4-2/4 Techlink, Singapore TEL: FX: ORIENTL MOTOR (THILND) CO., LTD. Headquarters & angkok Office 9, 8th Floor Zone C, Tonson Tower, Ploenchit Road, Lumpini, Pathumwan, angkok 3 Thailand TEL: FX: Lamphun Office 238/4 Moo 4, Tambol an-klang, mphur Muang, Lamphun 51 Thailand TEL: +66-() FX: +66-() ORIENTL MOTOR (INDI) PVT. LTD. No.81, 8th Floor, Prestige Meridian-1 No.29, M.G.Road, angalore, 561, India TEL: FX: ORIENTL MOTOR (MLYSI) SDN. HD. Headquarters & Kuala Lumpur Office --1, North Point Offices, Mid Valley City, No.1 Medan Syed Putra Utara 592 Kuala Lumpur, Malaysia TEL: FX: Penang Office Krystal Point II, Lebuh ukit Kecil 6, ayan Lepas, 119 Penang, Malaysia TEL: FX: Customer Support Centre TEL: For Singapore: (Toll Free) For Malaysia: (Toll Free) For Thailand: (Toll Free) For Other Countries: Mail to: support@orientalmotor.com.sg Japanese Customer Support Centre TEL: Mail to: j-support@orientalmotor.com.sg For more information please contact: Copyright ORIENTL MOTOR SI PCIFIC PTE. LTD. 216 Printed in Singapore 16Y 3K 6Y SVPD25