Compressed Gas Equipment

Transcription

1 Compressed Gas Equipment

2 VALVE ( ) TABLE OF CONTENTS PRODUCT INFORMATION AND ORDERING AV Series Acetylene Valve 01 AVB & AVMC Series Acetylene Valves 0 AV Series for WB Acetylene Valves 5 BV Series Hi/Lo Valves Series Chlorine Container Valves 9 Chlorine Valve Accessories 10 DF Series Dual Outlet Valves 11 JV Series O-Ring Style Industrial and Chrome Plated Valves 1 KVA Series Post Type Medical Valves 17 SHERCheck TV Series Residual Pressure Back Check Valves 19 TV Series Manifold Valves 21 TV Series Acetylene Valves 25 TV Series Industrial and Chrome Plated Valves 27 YV & YVA Series Line and Panel Valves 1 YVB Series Vertical Outlet Medical Oxygen Valves Fusible Plugs, Manifold Connectors 5

3 AV Series Acetylene Valves VALVE ( ) AV Series Wrench-operated Acetylene Valves Valve body made from rugged forging brass, precisely machined and gauged to help ensure long service life Valve body designed with large wrench flats for easy installation Large wrench flats on packing nut for easy tightening One-piece Chevron-shaped, pre-formed Polyethylene packing design ensures a positive leak-resistant seal One-piece steel stem is cold-rolled and plated to resist corrosion Stem shank is 1 2 " diameter with 4 " diameter thread, helping to ensure long life Stem point machined to close tolerances and micro-finish to ensure concentricity for a leak-tight seal 1

4 AV SERIES - WRENCH -OPERATED ACETYLENE VALVES Sherwood CGA Outlet Inlet Part Number Outlet Thread Size Thread Size Number AV NGO RH Ext NGT (Commercial) AV NGO RH Ext NGT (Commercial) AV NGO RH Ext NGT (Commercial) AV NGO LH Int NGT (P.O.L.) AV NGO LH Int NGT (P.O.L.) AV NGO LH Int NGT (P.O.L.) For technical information refer to Technical Section, page 1. Available on request: - Outlet caps and plugs with or without chain and rings. - Valves conforming to Department of Defense Specification MIL-DTL-2E. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CGO

5 AVB and AVMC Series Acetylene Valves VALVE ( ) AVB and AVMC Series Wrench-operated Acetylene Valves Valve body made from rugged forging brass, precisely machined and gauged to ensure long service life Fusible metal pressure relief device cast directly into valve body for maximum retainment and cylinder protection Large wrench flats on valve body for easy installation Nylon insert in packing nut resists loosening and does not damage valve body threads Tough carbon steel alloy stem is as strong as stainless steel State-of-the-art corrosion-resistant plating on stem aids in maximum protection New Teflon packing lasts up to ten times longer than graphite material Teflon packing has compression memory, reducing need for repetitive bonnet tightening

6 AVB AND AVMC SERIES - WRENCH OPERATED ACETYLENE VALVES Sherwood CGA Outlet Inlet Fusible Part Number Outlet Thread Size Thread Size Metal Number AVB NGO RH Ext NGT 212 F AVB521S* NGO RH Ext NGT None AVMC NGO RH Ext NGT 212 F AVMC201S* NGO RH Ext NGT None * Valves are supplied standard with inlet screen and red-colored bonnet for manifold service. For technical information refer to Technical Section, page. Available on request: - Stainless steel stems: To order, add _ to end of part number. ex: AVB521 becomes AVB521_ -,4,7, and 10 threads oversize and threads undersize inlets: To order, add -,-4,-7,-10 or -U/S to endof part number. ex: - threads undersize - AVB521 becomes AVB521-U/S. - threads oversize - AVB521 becomes AVB521- Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02NN97 4

7 AV Series WB Acetylene Valves VALVE ( ) AV Series Wrench-operated Valve for WB Style Acetylene Cylinders Valve body made from rugged forging brass, precisely machined and gauged to help ensure long service life Durable, corrosion-resistant stainless steel stem is machined to close tolerances and micro-finished for easy sealing, smooth operation and long life Conical micro-finished stem nose allows a wiping action on the valve body seat, helping to remove contamination and ensure a positive gas shut-off Internal tamper-resistant packing nut requires a special tool for removal and installation Chevron-shaped multiple packing design ensures a positive leak-resistant seal Vertical outlet and angled chamber provide easy access and operation inside of protective cylinder collar 5

8 AV SERIES - WRENCH OPERATED VALVES FOR WB STYLE ACETYLENE CYLINDERS Sherwood CGA Outlet Inlet Part Number Outlet Thread Size Thread Size Number AV5160WB NGO LH Int NGT-STD AV5160WB NGO LH Int NGT- Threads Oversize AV5160WB-U/S NGO LH Int NGT - Threads Undersize AV5160WB NG0 LH Int NGT- 6 Threads Oversize AV5160WB-6 U/S NGO LH Int NGT- 6 Threads Undersize AV5160WB NGO LH Int NGT - 9 Threads Oversize For technical information refer to Technical Section, page 5. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02PP97 6

9 BV Series Hi/Lo Valves VALVE ( ) BV Series Hi/Lo Pressure Regulating Dual Outlet Valves Integral regulator reduces gas pressure to the CGA-designated 000 psig max. outlet to psig, allowing for use of a UL -rated 000 psig regulator with the larger capacity lightweight high pressure cylinders Unique dual outlet design allows use of lower or higher cylinder service pressure from the same valve/cylinder package No special filling or withdrawal adapters needed Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Nickel 201 rupture disc resists premature rupture that may be caused by corrosive ambient environments Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Handwheel nut coated with corrosionresistant chromate/zinc organic plating Regulator designed for long service life. Cycle tested to in excess of 16,000 cycles Pressure Relief Device strategically located in regulated pressure outlet prevents cylinder pressure from reaching downstream equipment in the remote event of a catastrophic regulator failure 7

10 BV SERIES, HI/LO PRESSURE REGULATING, DUAL OUTLET CYLINDER VALVES Gas Service Air Inert Gases Oxygen Valve Part No. BV BV T BV Regulated Outlet CGA46 CGA580 CGA NGO RH Ext NGO RH Int NGO RH Ext High Pressure CGA47 CGA680 CGA701 Outlet/Fill Port NGO RH Ext NGO RH Int NGO RH Ext Long Nipple Regulated Outlet psig psig psig psig psig psig Inlet High Pressure 5,500 psi Max 5,500 psi Max 5,500 psi Max Outlet Pressure Rating Inlet Size 4-14 NGT 4-14 NGT 4-14 NGT 24 Threads Oversize 24 Threads Oversize 24 Threads Oversize Pressure Relief Device supplied standard for 4,500 psig cylinder with a test pressure Of 1.5 Times Service Pressure. Regulated Outlet Pressure Relief Device rupture pressure is psig. High pressure outlet plug removal tool supplied separately to cylinder filling plants only. To order use part number 680PW-2. Valves with other size inlets and outlets are special production. Please call Sherwood for availability. For technical information refer to technical section, page 7. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG06B97 8

11 Series Chlorine Cylinder and Container Valves VALVE ( ) Series Wrench-Operated Chlorine Cylinder and Container Valves Valves made in strict compliance with the standards and specifications of the Chlorine Institute Valve bodies forged from corrosionresistant aluminum silicon bronze alloy B Strong, chlorine-compatible Monel stems for long valve service Stem seal packing recognized by the Chlorine Institute Brass outlet cap with teflon insert included for outlet thread protection Chlorine valves are available with BS 41, DIN 477, JIS and other international thread standards 9

12 SERIES CHLORINE VALVES CGA Outlet Inlet Pressure Stem Part Number Outlet No. Thread Size Thread Size Relief Device Packing 1210-B RH 4-14 NGT CL F Garlock 1210-B RH 4-14 NGT CL F Garlock 1210-B RH 4-14 NGT CL- 165 F Garlock 1210-B RH 4-14 NGT CL F Garlock 1210-B RH 4-14 NGT CL F Garlock 1210X1-B RH 4-14 NGT CL F Teflon 1210X1-B RH 4-14 NGT CL F Teflon 1210X1-B RH 4-14 NGT CL- 165 F Teflon 1210X1-B RH 4-14 NGT CL F Teflon 1210X1-B RH 4-14 NGT CL F Teflon 1211-B RH NGT CL F Garlock 1211-B RH NGT CL F Garlock 1211-B RH NGT CL- 165 F Garlock 1211-B RH NGT CL F Garlock 1211-B RH NGT CL F Garlock 1211X1-B RH NGT CL F Teflon 1211X1-B RH NGT CL F Teflon 1211X1-B RH NGT CL- 165 F Teflon 1211X1-B RH NGT CL F Teflon 1211X1-B RH NGT CL F Teflon 1214-B RH 4-14 NGT CL-1 None Garlock 1214-B RH 4-14 NGT CL-2 None Garlock 1214-B RH 4-14 NGT CL- None Garlock 1214-B RH 4-14 NGT CL-4 None Garlock 1214-B RH 4-14 NGT CL-5 None Garlock 1214X1-B RH 4-14 NGT CL-1 None Teflon 1214X1-B RH 4-14 NGT CL-2 None Teflon 1214X1-B RH 4-14 NGT CL- None Teflon 1214X1-B RH 4-14 NGT CL-4 None Teflon 1214X1-B RH 4-14 NGT CL-5 None Teflon 1209-B RH NGT CL-1 None Garlock 1209-B RH NGT CL-2 None Garlock 1209-B RH NGT CL- None Garlock 1209-B RH NGT CL-4 None Garlock 1209-B RH NGT CL-5 None Garlock 1209X1-B RH NGT CL-1 None Teflon 1209X1-B RH NGT CL-2 None Teflon 1209X1-B RH NGT CL- None Teflon 1209X1-B RH NGT CL-4 None Teflon 1209X1-B RH NGT CL-5 None Teflon Ton container valves (1214 series) do not require a safety device. Chlorine valves accept outlet yoke Type 628 with appropriate adapters (see Chlorine Accessories). For technical information refer to technical section, page 11 Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco corporation, Gas and Fluid Control Group CHLV-2000BR 9.1

13 Chlorine Valve Accessories VALVE ( ) 585T and 1 Fusible Metal Plugs for Chlorine Valves Fusible metal plugs manufactured in accordance with Chlorine Institute specifications Fusible metal melting at F Type 585T has 7 2 " clear opening, 7 16 " Hex and 1 8 "-27 NGT external thread Type 1 has 11 2 " clear opening, " Hex and 4 "-14 NGT C1 external thread Made from Chlorine Institute recognized Naval Brass and fusible alloy 628 Chlorine Yoke 6414 Flexible Line Connectors 8 " OD zinc-plated copper Maximum working pressure of 500 psig 5888 High Flow Yoke Adapters Use with P10-CLAL outlet gasket Made in compliance with Chlorine Institute specifications Made from steel with a plated finish 65 Chlorine Wrenches Forged steel construction Designed for use with all standard chlorine cylinder and container valves and yokes 154 Reseating Tool (not shown) Manually operated Increases valve service 10

14 585T FUSIBLE METAL PLUGS Part Number Thread Size First Thread Diameter 585T 1 8 " 27 NGT 0.91" (standard) 585X1T 1 8 " 27 NGT (oversize) 1 FUSIBLE METAL PLUGS Part Number Thread Size First Thread Diameter 1-N1 4 " 14 NGT CL " (standard) 1-N2 4 " 14 NGT CL " (.0179" oversize) 1-N 4 " 14 NGT CL " (.08" oversize) 1-N4 4 " 14 NGT CL " (.0625" oversize) 1-N5 4 " 14 NGT CL " (.125" oversize) 10-N1 1" NGT CL " (standard) 10-N2 1" NGT CL " (.0179" oversize) 10-N 1" NGT CL- 1.21" (.08" oversize) 10-N4 1" NGT CL " (.0625" oversize) 10-N5 1" NGT CL " (.125" oversize) 6414 FLEXIBLE LINE CONNECTORS Part Number Thread Size Length 6414C CGA 820 (Both Ends) 6 ft. 6414X1C CGA 820 (Both Ends) 10 ft. 6414X2C CGA 820 (Both Ends) 4 ft. 6414X7C CGA 820 X 5 8 "-18 UNF 6 ft. 6414X8C 5 8 "-18" UNF (Both Ends) 4 ft. 6414X9C 5 8 "-18" UNF (Both Ends) 6 ft. 6414X10C CGA 820 X 5 8 "-18 UNF 4 ft. Part Number Size " SAE Flare S 8 " ODS " SAE 5888-D 1 2 " 14NPT (Male) 5888-E 1.00" Union Outlet Adapter 5888 HIGH FLOW YOKE ADAPTERS 65 CHLORINE WRENCHES Part Number Size " open end, 8 " stem square, straight shaft 65X " open end, 8 " stem square, twisted shaft Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood,Harsco Corporation, Gas and Fluid Control Group CHLA-2000BR 10.1

15 DF Series Dual Outlet Valves VALVE ( ) DF Series Packed Dual Outlet Valves for Manifolding Applications Dual outlet design allows manifolding without use of adapters or tees, eliminating multiple joints Location of outlets above valve seat allows individual cylinder isolation without shutting off manifold Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Nickel 201 rupture disc resists premature rupture that may be caused by corrosive ambient environments Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Handwheel nut coated with corrosionresistant chromate/zinc organic plating 11

16 DF SERIES - PACKED DUAL OUTLET VALVES FOR MANIFOLDING APPLICATIONS Gas Outlet Part Number Outlet Inlet Service Orientation Number Of Outlets Thread Size Thread Size Air Horizontal DF11551-XXHFKF UNF2A Straight Oxygen Vertical DF11651-XXFKF Two NPT UNF2A Straight Inert Gas Horizontal DF11561-XXHFKF 180 Apart Female 4-14 NGT Tapered Vertical DF11661-XXFKF 4-14 NGT Tapered CNG Horizontal DF11555-XXHFKF UNF2A Straight Hydrogen Vertical DF11655-XXFKF Two NPT 4-14 NGT Tapered Methane Horizontal DF11565-XXHFKF 180 Apart Female 4-14 NGT Tapered Vertical DF11665-XXFKF 4-14 NGT Tapered Air Vertical TV10451-XXFKF One NPT UNF2A Straight Oxygen TV10461-XXFKF Female 4-14 NGT Tapered Inert Gas CNG Vertical TV10455-XXFKF One NPT UNF2A Straight Hydrogen TV10465-XXFKF Female 4-14 NGT Tapered Methane XX - Denotes Pressure Relief Device burst disc rupture pressure. See page xix for part number suffix. For technical information refer to Technical Section, page 1. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02YY97 12

17 JV Series O-Ring Style Industrial and Chrome Plated Valves VALVE ( ) JV Series O-Ring Seal Industrial Valves Very easy operating. Ideal for laboratory or medical applications. Unique O-Ring chamber design prolongs service life by allowing low torque operation while helping to create a dependable seal Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Nickel 201 rupture disc resists premature rupture that may be caused by corrosive ambient environments Precise, quality machining results in exceptional finishes for low torque sealing and long packing life 1

18 JV SERIES - O-RING SEAL INDUSTRIAL VALVES Gas CGA Pin Indexing Inlet Sherwood Service Outlet Hole Numbers Thread Size Part Number Number Air (R729) 0 psi TO,000 psi NGO RH Ext NGT JV4641-XX 4-14 NGT JV4661-XX NGT JV4681-XX UNF JV4651-XX-75 1,125-12UNF JV4651-XX,001 psi TO 5,500 psi NGO RH Ext NGT JV4761-XX (Long Nipple) 5,501 psi TO 7,500 psi NGO RH Int NGT JV70261-XX Argon 0 psi TO,000 psi NGO RH Int NGT JV5841-XX 4-14 NGT JV5861-XX NGT JV5881-XX UNF JV5851-XX UNF JV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT JV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT JV67761-XX Butane/Propane NGO LH Ext NGT JV55541-XX Liquid Withdrawal 4-14 NGT JV55561-XX NGT JV55581-XX UNF JV55551-XX UNF JV55551-XX Carbon Dioxide (R744) NGO RH Ext NGT JV241-XX 4-14 NGT JV261-XX NGT JV281-XX UNF JV251-XX UNF JV251-XX Carbon Monoxide NGO LH Ext NGT JV545-XX 0 psig TO,000 psig 4-14 NGT JV565-XX NGT JV585-XX UNF JV555-XX UNF JV555-XX,001 psi TO 5,500 psi NGO LH Int NGT JV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT JV7065-XX 1,2 Dichloroethylene NGO RH Ext NGT JV6640 (R110) (Face Washer) 4-14 NGT JV NGT JV UNF JV UNF JV6650 Helium 0 psi TO,000 psi NGO RH Int NGT JV5841-XX 4-14 NGT JV5861-XX NGT JV5881-XX UNF JV5851-XX UNF JV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT JV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT JV67761-XX Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02SS97 14

19 JV SERIES - O-RING SEAL INDUSTRIAL VALVES Gas CGA Pin Indexing Inlet Sherwood Service Outlet Hole Numbers Thread Size Part Number Number Hydrogen 0 psi TO,000 psi NGO RH Ext NGT JV545-XX 4-14 NGT JV565-XX NGT JV585-XX UNF JV555-XX UNF JV555-XX,001 psi TO 5,500 psi NGO LH Int NGT JV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT JV7065-XX Krypton 0 psi TO,000 psi NGO RH Int NGT JV5841-XX 4-14 NGT JV5861-XX NGT JV5881-XX UNF JV5851-XX UNF JV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT JV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT JV67761-XX Methane (R50) 0 psi TO,000 psi NGO LH Ext NGT JV545-XX 4-14 NGT JV565-XX NGT JV585-XX UNF JV555-XX UNF JV555-XX,001 psi TO 5,500 psi NGO LH Int NGT JV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT JV7065-XX Natural Gas 0 psi TO,000 psi NGO LH Ext NGT JV545-XX 4-14 NGT JV565-XX NGT JV585-XX UNF JV555-XX UNF JV555-XX,001 psi TO 5,500 psi NGO LH Int NGT JV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT JV7065-XX Neon 0 psi TO,000 psi NGO RH Int NGT JV5841-XX 4-14 NGT JV5861-XX NGT JV5881-XX UNF JV5851-XX UNF JV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT JV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT JV67761-XX Nitrogen 0 psi TO,000 psi NGO RH Int NGT JV5841-XX 4-14 NGT JV5861-XX NGT JV5881-XX UNF JV5851-XX UNF JV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT JV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT JV67761-XX 15

20 JV SERIES - O-RING SEAL INDUSTRIAL VALVES Gas CGA Pin Indexing Inlet Sherwood Service Outlet Hole Numbers Thread Size Part Number Number Nitrous Oxide (R744a) NGO RH Ext NGT JV2641-XX (Small round 4-14 NGT JV2661-XX nipple) NGT JV2681-XX UNF JV2651-XX UNF JV2651-XX Oxygen 0 psi TO,000 psi NGO RH Ext NGT JV5441-XX 4-14 NGT JV5461-XX NGT JV5481-XX UNF JV5451-XX UNF JV5451-XX,001 psi TO 4,000 psi NGO RH Ext NGT JV57761-XX 4,001 psi TO 5,500 psi NGO RH Ext NGT JV70161-XX Sulfur Dioxide NGO RH Ext NGT JV (Face Washer) 4-14 NGT JV NGT JV UNF JV UNF JV Xenon 0 psi TO,000 psi NGO RH Int NGT JV5841-XX 4-14 NGT JV5861-XX NGT JV5881-XX UNF JV5851-XX UNF JV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT JV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT JV67761-XX XX - Denotes Pressure Relief Device burst disc rupture pressure. See page xix for part number suffix. For technical information refer to Technical Section, page 17. Available on Request: - 4 and 7 threads oversize inlets: To order, add -4 or -7 to end of part number. ex: JV4661-XX becomes JV4661-XX-7 - Chrome plating: To order, add letter A after letters JV in part number. ex: JV4661-XX becomes JVA 4661-XX - Anti-surge feature: To order, add letter N after part number. ex: JV4661-XX becomes JV4661-XXN - Fusible backed pressure relief devices in 165 F or 212 F nominal melting temperatures: To order, change the 1 in the part number to 4 for 165 or to a 5 for 212. ex: JV4661-XX becomes JV4664-XX for 165 or JV4665-XX for Lexan polycarbonate handwheel To order, add suffix LX to end of part number. ex: JV becomes JV5451-2LX Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02SS97 16

21 KVA Series Post Type Medical Valves VALVE ( ) KVA Series Post Medical Valves Strong, durable brass body made from extruded brass rod will fit all yokes made to CGA860 drawing specifications Protective and attractive chrome finish Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Chamber design minimizes risk of broken stems caused by careless handling of cylinders Single unit, compact pressure relief resists tampering Nickel 201 rupture disc resists premature rupture that may be caused by corrosion from ambient environments Large wrench flats on bonnet for easy removal Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Secondary O-Ring seal located above Teflon packing helps provide secure seal under vacuum purging and low pressure operation Copper sealing gasket provides permanent, leak-resistant bonnet seal Oxygen cleaned with aqueous detergent to CGA Specification G4.1 17

22 KVA SERIES - POST MEDICAL VALVES Gas CGA Pin Indexing Inlet Sherwood Service Outlet Hole Numbers Thread Size Part Number Number Air (R729) 950 Pins #1 AND # NGT KVA9544F UNF-2A KVA9554B-2 Carbon Dioxide 940 Pins #1 AND # NGT KVA UNF-2A KVA Cyclopropane 920 Pins # AND # NGT KVA UNF-2A KVA Ethylene 900 Pins #1 AND # NGT KVA9044F UNF-2A KVA9054B-2 Helium 90 Pins #4 AND # NGT KVA944F UNF-2A KVA954B-2 Medical Gas Mixtures 97 Pins #11 AND # NGT KVA9744F UNF-2A KVA9754B-2 Nitrogen 960 Pins #1 AND # NGT KVA9644F UNF-2A KVA9654B-2 Nitrous Oxide 910 Pins # AND # NGT KVA UNF-2A KVA Nitrous Oxide & 965 Pin # NGT KVA96544F-2 Oxygen Mixtures UNF-2A KVA96554B-2 Oxygen 870 Pins #2 AND # NGT KVA8744F UNF-2A KVA8754B-2 Oxygen & Carbon 880 Pins #2 AND # NGT KVA8844F-2 Dioxide Mixtures UNF-2A KVA8854B-2 Oxygen & Helium 890 Pins #2 AND # NGT KVA8944F-2 Mixtures UNF-2A KVA8954B-2 All valves supplied with 165 F fusible metal backed, flush style pressure relief devices and copper alloy rupture discs except Carbon Dioxide (KVA9451-2), Nitrous Oxide (KVA9151-2), and Cyclopropane (KVA9251-2) which are supplied with unbacked hex-style pressure relief devices and nickel 201 rupture discs. All valves are supplied with rupture discs rated for 2015 psig service pressure cylinders. Rupture discs rated for other service pressures available on request. For technical information refer to Technical Section, page 21. Available on request: - Lexan polycarbonate, wing style handwheel: To order, add H to end of part number (only available on uuf2a inlet valves). ex: KVA8754B-2 becomes KVA8754B-2H - Chrome-plated brass toggle lever: To order, add TG to end of part number. ex: KVA8754B-2 becomes KVA8754B-2TG - Kel-F seat material: To order, add K to end of part number. ex: KVA8745B-2 becomes KVA8754B-2K "-27 NPT gauge port: To order, add G to end of part number. ex: KVA8754B-2 becomes KVA8754B-2G Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02LL97 18

23 SHERCheck TV Series Residual Pressure Back Check Valves VALVE ( ) SHERCheck TV Series Residual Pressure Back Check Valves Retentive pressure of <0 psig maintains integrity of empty cylinder against aspiration of contaminants caused by open valve Integral back check mechanism helps prevent backflow if system pressure becomes higher than cylinder pressure Residual pressure/back check piston made of strong stainless steel for extended service life Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Nickel 201 rupture disc resists premature rupture that may be caused by corrosive ambient environments Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Handwheel nut coated with corrosionresistant chromate/zinc organic plating 19

24 SHERCHECK TV SERIES - RESIDUAL PRESSURE BACKCHECK VALVES Gas CGA Outlet Inlet Sherwood Service Outlet Thread Size Thread Size Part Number Number Air (R729) NGO RH Ext NGT TV4661PR-XX NGO RH Ext NGT TV4761PR-XX Argon NGO RH Int NGT TV5861PR-XX NGO RH Int NGT TV68061PR-XX Carbon Monoxide NGO LH Ext NGT TV565PR-XX NGO LH Int NGT TV69565PR-XX Helium NGO RH Int NGT TV5861PR-XX NGO RHInt NGT TV68061PR-XX Hydrogen NGO RH Ext NGT TV565PR-XX NGO LHInt NGT TV69561PR-XX Krypton NGO RH Int NGT TV5861PR-XX NGO RH Int NGT TV68061PR-XX Methane (R50) NGO LH Ext NGT TV565PR-XX NGO LH Int NGT TV69565PR-XX Natural Gas NGO LH Ext NGT TV565PR-XX NGO LH Int NGT TV69565PR-XX Neon NGO RH Int NGT TV5861PR-XX NGO RHInt NGT TV68061PR-XX Nitrogen NGO RH Int NGT TV5861PR-XX NGO RHInt NGT TV68061PR-XX Oxygen NGO RH Ext NGT TV5461PR-XX NGO RH Ext NGT TV57761PR-XX Xenon NGO RH Int NGT TV5861PR-XX NGO RH Int NGT TV68061PR-XX XX - Denotes Pressure Relief Device burst disc rupture pressure. See page xix for part number suffix. For technical information see Technical Section, page 25. Available on request: - 4 and 7 threads oversize inlets: To order, add -4 or -7 to end of part number. ex: TV4661PR-XX becomes TV4661PR-XX-7. - Chrome plating: To order, add letter A after letters TV in part number. ex: TV4661PR-XX becomes TVA 4661PR-XX - Anti-Surge Feature: To order, add letter N after part number. ex: TV4661PR-XX becomes TV4661PR-XXN - Fusible backed pressure relief devices in 165 F or 212 F nominal melting temperatures: To order, change the 1 in the part number to 4 for 165 or to 5 for 212. ex: TV4661PR-XX becomes TV4664PR-XX for 165 or TV4665PR-XX for Rubber covered handwheel: To order, add letters HC after part number. ex: TV4661PR-XX becomes TV4661PR-XXHC. Filling Adapter Part Numbers With Retractable Pin Without Retractable Pin For CGA46 outlet order P/N TL46AA TL46D For CGA50 outlet order P/N TL50AA TL50D For CGA540 outlet order P/N TL540AA TL540D For CGA580 outlet order P/N TL580AA TL580D For other CGA Outlets please contact the factory for ordering infomation. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02WW97 20

25 TV Series Manifold Valves VALVE ( ) TV Series Packed Industrial Manifold Valves Secondary O-Ring seal located above Teflon packing provides secure seal under low pressure operation Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon-coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Handwheel nut coated with corrosionresistant chromate/zinc organic plating 21

26 TV SERIES - PACKED INDUSTRIAL MANIFOLD VALVES Gas CGA Outlet Inlet Sherwood Service Outlet Thread Size Thread Size Part Number Number Air (R729) 0 psi TO,000 psi NGO RH Ext NGT TV NGT TV4660,001 psi TO 5,500 psi NGO RH Ext NGT TV4760 Long Nipple 5,501 psi TO 7,500 psi NGO RH Int NGT TV70260 Argon 0 psi TO,000 psi NGO RH Int NGT TV NGT TV psi TO 5,500 psi NGO RH Int NGT TV ,501 psi TO 7,500 psi NGO LH Ext NGT TV67760 Carbon Dioxide (R744) NGO RH Ext NGT TV NGT TV260 Carbon Monoxide 0 psi TO,000 psi NGO LH Ext NGT TV NGT TV560,001 psi TO 5,500 psi NGO LH Int NGT TV ,501 psi TO 7,500 psi NGO LH Int NGT TV7060 Helium 0 psi TO,000 psi NGO RH Int NGT TV NGT TV5860,001 psi TO 5,500 psi NGO RH Int NGT TV ,501 psi TO 7,500 psi NGO LH Ext NGT TV67760 Hydrogen 0 psi TO,000 psi NGO LH Ext NGT TV NGT TV psi TO 5,500 psi NGO LH Int NGT TV ,501 psi TO 7,500 psi NGO LH Int NGT TV7060 Krypton 0 psi TO,000 psi NGO RH Int NGT TV NGT TV5860,01 psi TO 5,500 psi NGO RH Int NGT TV ,501 psi TO 7,500 psi NGO LH Ext NGT TV67760 Methane (R50) 0 psi TO,000 psi NGO LH Ext NGT TV NGT TV560,001 psi TO 5,500 psi NGO LH Int NGT TV ,501 psi TO 7,500 psi NGO LH Int NGT TV7060 Natural Gas 0 psi TO,000 psi NGO LH Ext NGT TV NGT TV560,001 psi TO 5,500 psi NGO LH Int NGT TV ,501 psi TO 7,500 psi NGO LH Int NGT TV7060 Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02TT97 22

27 TV SERIES - PACKED INDUSTRIAL MANIFOLD VALVES Gas CGA Outlet Inlet Sherwood Service Outlet Thread Size Thread Size Part Number Number Neon 0 psi TO,000 psi NGO RH Int NGT TV NGT TV5860,01 psi TO 5,500 psi NGO RH Int NGT TV ,501 psi TO 7,500 psi NGO LH Ext NGT TV67760 Nitrogen 0 psi TO,000 psi NGO RH Int NGT TV NGT TV5860,01 psi TO 5,500 psi NGO RH Int NGT TV ,501 psi TO 7,500 psi NGO LH Ext NGT TV67760 Nitrous Oxide (R744a) NGO RH Ext NGT TV2640 (Small round nipple) 4-14 NGT TV2660 Oxygen 0 psi TO,000 psi NGO RH Ext NGT TV NGO RH Ext NGT TV5460,001 psi TO 4,000 psi NGO RH Ext NGT TV ,001 psi TO 5,500 psi NGT TV70160 Sulfur Dioxide NGO RH Ext NGT TV6640 (Face Washer) 4-14 NGT TV6660 Xenon 0 psi TO,000 psi NGO RH Int NGT TV NGT TV5860,001 psi TO 5,500 psi NGO RH Int NGT TV ,501 psi TO 7,500 psi NGO LH Ext NGT TV67760 For technical information refer to Technical Section, page 27. 2

28 Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02TT97 24

29 TV Series Acetylene Valves VALVE ( ) TV Series Handwheel-Operated Acetylene Valves Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Secondary O-Ring seal located above Teflon packing helps provide secure seal under vacuum purging and low pressure operation Handwheel nut coated with corrosionresistant chromate/zinc organic plating 25

30 TV SERIES - HANDWHEEL OPERATED ACETYLENE VALVES Sherwood CGA Outlet Inlet Part Number Outlet Thread Size Thread Size Number TV "-14 NGO RH Ext. 1 2 "-14 NGT (Commercial) TV "-14 NGO RH Ext. 4 "-14 NGT (Commercial) TV "-14 NGO RH Ext. 1" NGT (Commercial) TV "-14 NGO LH Ext. 4 "-14 NGT (Canadian Std.) TV "-14 NGO LH Int. 1 2 "-14 NGT (P.O.L.) TV "-14 NGO LH Int. 4 "-14 NGT (P.O.L.) TV "-14 NGO LH Int. 1" NGT (P.O.L.) For technical information refer to Technical Section, page 29. Available on request: - Outlet caps and plugs with or without chain and rings. - Valves conforming to Department of Defense Specification MIL-DTL-2E. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG0L97 26

31 TV Series Industrial and Chrome Plated Valves VALVE ( ) TV Series Packed Pressure Seal Style Industrial and Chrome Plated Valves Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications High-temperature aluminum alloy handwheel with large drainage holes Integral stainless steel tang helps prevent internal stem breakage Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internally threaded chamber design promotes longer life and helps protect valve body chamber threads from damage Nickel 201 rupture disc resists premature rupture that may be caused by corrosive ambient environments Precise, quality machining results in exceptional finishes for low torque sealing and long packing life Inert Teflon packing provides leak-free stem seal, long cycle life and resistance to corrosion Handwheel nut coated with corrosionresistant chromate/zinc organic plating Where applicable, Nickel chrome plated for durability. Also provides a protective coating to help shield the valve from liquids and cleaning solutions containing ammonia, chlorine and other chemicals harmful to copper alloys. 27

32 TV SERIES - PACKED PRESSURE SEAL STYLE INDUSTRIAL VALVES Gas CGA Outlet Inlet Sherwood Service Outlet Thread Size Thread Size Part Number Number Air (R729) 0 psi TO,000 psi NGO RH Ext NGT TV4641-XX 4-14 NGT TV4661-XX NGT TV4681-XX UNF TV4651-XX UNF TV4651-XX,001 psi TO 5,500 psi NGO RH Ext NGT TV4761-XX (Long Nipple) 5,501 psi TO 7,500 psi NGO RH Int NGT TV70261-XX Argon 0 psi TO,000 psi NGO RH Int NGT TV5841-XX 4-14 NGT TV5861-XX NGT TV5881-XX UNF TV5851-XX UNF TV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT TV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT TV67761-XX Butane/Propane NGO LH Ext NGT TV55541-XX Liquid Withdrawal 4-14 NGT TV55561-XX NGT TV55581-XX UNF TV55551-XX UNF TV55551-XX Carbon Dioxide (R744) NGO RH Ext NGT TV241-XX 4-14 NGT TV261-XX NGT TV281-XX UNF TV251-XX UNF TV251-XX Carbon Monoxide NGO LH Ext NGT TV545-XX 0 psi TO,000 psi 4-14 NGT TV565-XX NGT TV585-XX UNF TV555-XX UNF TV555-XX,001 psi TO 5,500 psi NGO LH Int NGT TV69561-XX 5,501 psi TO 7,500 psi NGO LH Int NGT TV7065-XX 1,2 Dichloroethylene NGO RH Ext NGT TV6640 (R110) (Face Washer) 4-14 NGT TV NGT TV UNF TV UNF TV6650 Helium 0 psi TO,000 psi NGO RH Int NGT. TV5841-XX 4-14 NGT TV5861-XX NGT TV5881-XX UNF TV5851-XX UNF TV5851-XX,001 psi TO 5,501 psi NGO RH Int NGT TV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT TV67761-XX Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02QQ97 28

33 TV SERIES - PACKED PRESSURE SEAL STYLE INDUSTRIAL VALVES Gas CGA Outlet Inlet Sherwood Service Outlet Thread Size Thread Size Part Number Number Hydrogen 0 psi TO,000 psi NGO LH Ext NGT TV545-XX 4-14 NGT TV565-XX NGT TV585-XX UNF TV555-XX UNF TV555-XX,001 psi TO 5,500 psi NGO LH Int NGT TV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT TV7065-XX Krypton 0 psi TO,000 psi NGO RH Int NGT TV5841-XX 4-14 NGT TV5861-XX NGT TV5881-XX UNF TV5851-XX UNF TV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT TV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT TV67761-XX Methane (R50) 0 psi TO,000 psi NGO LH Ext NGT TV545-XX 4-14 NGT TV565-XX NGT TV585-XX UNF TV555-XX UNF TV555-XX,001 psi TO 5,501 psi NGO LH Int NGT TV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT TV7065-XX Natural Gas 0 psi TO,000 psi NGO LH Ext NGT TV545-XX 4-14 NGT TV565-XX NGT TV585-XX UNF TV555-XX UNF TV555-XX,001 psi TO 5,500 psi NGO LH Int NGT TV69565-XX 5,501 psi TO 7,500 psi NGO LH Int NGT TV7065-XX Neon 0 psi TO,000 psi NGO RH Int NGT TV5841-XX 4-14 NGT TV5861-XX NGT TV5881-XX UNF TV5851-XX UNF TV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT TV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT TV67761-XX Nitrogen 0 psi TO,000 psi NGO RH Int NGT TV5841-XX 4-14 NGT TV5861-XX NGT TV5881-XX UNF TV5851-XX UNF TV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT TV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT TV67761-XX 29

34 TV SERIES - PACKED PRESSURE SEAL STYLE INDUSTRIAL VALVES Gas CGA Outlet Inlet Sherwood Service Outlet Thread Size Thread Size Part Number Number Nitrous Oxide (R744a) NGO RH Ext NGT TV2641-XX (Small round nipple) 4-14 NGT TV2661-XX NGT TV2681-XX UNF TV2651-XX UNF TV2651-XX Oxygen 0 psi TO,000 psi NGO RH Ext NGT TV5441-XX 4-14 NGT TV5461-XX NGT TV5481-XX UNF TV5451-XX UNF TV5451-XX,001 psi TO 4,000 psi NGO RH Ext NGT TV57761-XX 4,001 psi TO 5,500 psi NGO RH Ext NGT TV70161-XX Sulfur Dioxide NGO RH Ext NGT TV ( Face Washer) 4-14 NGT TV NGT TV UNF TV UNF TV Xenon 0 psi TO,000 psi NGO RH Int NGT TV5841-XX 4-14 NGT TV5861-XX NGT TV5881-XX UNF TV5851-XX UNF TV5851-XX,001 psi TO 5,500 psi NGO RH Int NGT TV68061-XX 5,501 psi TO 7,500 psi NGO LH Ext NGT TV67761-XX XX - Denotes Pressure Relief Device burst disc rupture pressure. See page xix for part number suffix. For technical information refer to Technical Section, page 1. Available with: - 4 and 7 threads oversize inlets: To order add -4 or -7 to end of part number. ex: TV4661-XX becomes TV4661-XX-7. - Chrome Plating: To order, add letter A after letters TV in part number. ex: TV4661-XX becomes TVA 4661-XX - Anti-Surge Feature: To order, add letter N after part number. ex: TV4661-XX becomes TV4661-XXN - Fusible backed pressure relief devices in 165 F or 212 F nominal melting temperatures: To order, change 1 in the part number to 4 for 165 or to 5 for 212. ex: TV4661-XX becomes TV4664-XX for 165 or TV4665-XX for Lexan polycarbonate handwheels To order, add suffix LX to end of part number. ex: TV4651-XX becomes TV4651-XXLX Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02QQ97 0

35 YV and YVA Series Line and Panel Valves VALVE ( ) YV and YVA Series Line Valves Strong, durable forged brass body manufactured by Sherwood to specifications stricter than most commercial forging specifications Designed for use in service pressure up to 6,000 psig Compact design especially suited for use on compressor or cascade panels Chamber specially designed for low torque operation Stainless steel stem design for dependable service and long life Proprietary dual packing chamber design provides dependable seal characteristics and long service life and easy operation Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internal protected bonnet gasket seal provides positive, damage-resistant chamber seal Compact molded Lexan polycarbonate handwheel is easy to use 1

36 YV AND YVA SERIES LINE VALVES Part Inlet Outlet Panel Panel Chrome Number Thread Size Thread Size Mount Hole Size Plated YV NPT Int NPT Ext. No No YVA NPT Int NPT Ext. No Yes YV010A NPT Int NPT Ext. Yes No YVA010A NPT Int NPT Ext. Yes Yes For technical information refer to Technical Section, page 5. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02ZZ97 2

37 YVB Series Vertical Outlet Medical Oxygen Valves VALVE ( ) YVB Series Vertical Outlet Medical Oxygen Valves Compact design for use on small medical aluminum and composite oxygen cylinders (home health care applications) Chamber designed for easy operation Stainless steel stem design for dependable service and long life Durable lower plug made of tough naval brass resists wear Lower plug is Teflon -coated to add lubricity, which minimizes seizing and galling especially under high pressure operation Internal bonnet gasket seal resists damage to chamber sealing area Compact molded Lexan polycarbonate handwheel is easy to operate Single unit, compact pressure relief device incorporates 165 F fusible metal backing to resist premature rupture and provide maximum cylinder protection Chrome plated for corrosion resistance and cosmetic appeal Oxygen cleaned with aqueous detergent to CGA specification G4.1

38 YVB SERIES - VERTICAL OUTLET MEDICAL OXYGEN VALVES Part Number CGA Outlet Thread Inlet Gauge Outlet Size Thread Size Port YVB5454-XX NGO RH Ext UNF2A None YVB5454-XX-62G NGO RH Ext UNF2A 1 8 NPT YVB5454-XX NGO RH Ext UNF2A None YVB5454-XX-75G NGO RH Ext UNF2A 1 8 NPT For technical information refer to Technical Section, page 7. All valves supplied with 165 F fusible metal backed, flush style, pressure relief devices and copper alloy rupture discs. XX denotes Pressure Relief Device burst disc rupture pressure. See page xix for part number suffix. All valves are supplied with rupture discs rated for 2015 psig service pressure cylinders. Rupture discs rated for other service pressures available on request. Available on request: - Pressure relief devices without fusible metal. - Kel-F - Hex-style, exhaust equalizing, pressure relief device plugs - Pressure Relief Devices for cylinders other than 2015 psig service pressure UNF inlets with O-Ring glands in conformance with Military specifications. - Round, Barrel style Lexan handwheel. Sherwood and the SS symbol are trademarks of Sherwood, Harsco Corporation, Gas and Fluid Control Group All other names are trademarks of their respective owners Sherwood, Harsco Corporation, Gas and Fluid Control Group T-CG02XX97 4

39 Fusible Plugs Manifold Connectors VALVE ( ) Fusible Plugs All fuse plugs are UL Listed Produced from high quality brass and steel alloy rod Meticulously controlled fusible alloy assures accurate and consistent melt temperatures Fusible alloy is cast into plug body to ensure an extremely strong bond between alloy and plug body Fusible plug stamped with fusible metal yield temperature Manifold Station Connectors and Trailer Tube Pressure Relief Devices Manifold Station Connectors are specifically designed for use on charging manifolds, manifold banks or gas distribution systems Station connectors are available with or without pressure relief devices Trailer Tube pressure relief devices are made using the same components as the dependable "TV" series cylinder valve Rupture discs are made of corrosion resistant nickel 201 Available with a 4-16 SAE flare outlet for overboard dumping 5