Cable Duct AS-i 3.0 Motor Modules

Transcription

1 Cable Duct.0 Motor Modules Cable Duct.0 Motor Modules for two V Motorized Rollers Interroll (EC0) resp. RULMECA (RDR BL-) QS and viam8 connectors and via profile cable Flat design, optimized for use in cable channels Inputs and Outputs in one module ASI BW90 Speed setting via parameters (Figure similar) Figure ASI BW90 QS () () () () () Drive () Number of Line drives protection fuse () Flat design, montage in cable duct possible Inputs digital Outputs digital Outputs analog Input voltage (sensor supply) () Output voltage (actuator supply) () connection Interroll, RULMECA out of out of profile cable BW90 Interroll, RULMECA out of out of using M8 BW89 () Article No. Interroll (EC0), RULMECA (RDR BL-): Motor module to control V motorized rollers Interroll Typ EC0 or RULMECA Typ RDR BL-., separately for each motor,, A (slow-blow fuse): In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the fuse the module is no longer functional and needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains. Input voltage (sensor supply): Inputs are supplied by or by (auxiliary V power). If supplied by, inputs shall not be connected to earth or to external potential. Output voltage (actuator supply): Outputs are supplied by or by (auxiliary V power). If supplied by, outputs shall not be connected to earth or to external potential. connection: The connection to as well to (auxiliary V power) is made via yellow resp. black profile cable with piercing technology or via M8 socket. Bihl+Wiedemann GmbH Floßwörthstr. D-6899 Mannheim Phone: (+9) 6/996-0 Fax: (+9) 6/99 mail@bihl-wiedemann.de We reserve the right to change any data Mannheim, 6..6 page

2 Cable Duct.0 Motor Modules Article No. BW90 BW89 General data Roller drives x Interroll (EC0) or x RULMECA (RDR BL-) Connection / connection profile cable and piercing M8 Periphery connection M8 Profile S-7.A.7, ID = 7 (fixed) Address AB slave Required Master profile M As of specification.0 Operating voltage 0 V (8.6 V) Max. current consumption 00 ma Operating voltage V (8 0V) Max. current consumption 6 A continuously, A peak () Input Number x sensor inputs + x motor fault inputs Power supply sensor inputs: out of motor fault inputs: out of Power supply of 00 ma () attached sensors Switching threshold U in <V (low) U in > V (high) Output Number (digital) Number (analog) Power supply out of (galvanic separation) Overvoltage tolerated by reaction () Max. output current Motor supply V resistant brake resistor compatible 0 ma per output, in sum 0 ma at T amb 0 C, ma at T amb >0 C out of, A continuously,, A max. Line protection fuse, separately for each motor,. AT, at 7 A (00%) release between s and 0 s, fuse UL certified () Display LED I...Ix (yellow) state of inputs I, I LED M, M (yellow) state of outputs M (O), M (O) LED ASI (green) on: voltage on off: no voltage LED (green) on: V DC off: no V DC LED FLT/FAULT (red) on: slave address 0 or slave offline flashing: voltage is missing, overload output, an output is short circuited, at least one motor fuse has blown or overload sensor off: slave online Bihl+Wiedemann GmbH Floßwörthstr. D-6899 Mannheim Phone: (+9) 6/996-0 Fax: (+9) 6/99 mail@bihl-wiedemann.de page Mannheim, 6..6 We reserve the right to change any data

3 Cable Duct.0 Motor Modules Article No. BW90 BW89 Environment Applied standards EN EN EN609 Operating altitude max. 000 m Ambient temperature - C C (non-condensing) () () (- C... + C at max., A current consumption) Storage temperature - C C Housing plastic, screw mounting Protection category IP Weight module: 00 g passive distributor: 7 g module: 00 g Dimensions (W / H / D) in mm module: 90 / 60 / 8 passive distributor: 60 / /9 module: 90 / 60 / 8 () Max. current consumption out of (Derating) BW89, BW90 I max. [A] 6,0,0, T amb [ C] () Power supply of attached sensors (Derating) BW89, BW90 I max. [ma] T amb [ C] Bihl+Wiedemann GmbH Floßwörthstr. D-6899 Mannheim Phone: (+9) 6/996-0 Fax: (+9) 6/99 mail@bihl-wiedemann.de We reserve the right to change any data Mannheim, 6..6 page

4 Cable Duct.0 Motor Modules () In the motor module UL approved fuses are placed before each of the motor supply connections. A short circuit in the motor causes this fuse to blow, protecting the connection cable between the module and motor. After blowing the fuse the module is no longer functional and needs to be replaced. The characteristics of the fuse must be checked against the motor data before using the module. The protection circuit in the module allows a very simple protection of the motor cables. The fuse for the cable protection is a slow-blow one; without short circuit the robust behavior of the module remains. internal line protection V ext.in 0 V ext.in M M () If the cables are fixed installed, an operating temperature up to -0 C... + C is permissible. Configuration analog value BW89, BW90 parameters analog value Pin P0 P P O/O , V, V, V,6 V 6,7 V 7,8 V 8,9 V 0 V Bihl+Wiedemann GmbH Floßwörthstr. D-6899 Mannheim Phone: (+9) 6/996-0 Fax: (+9) 6/99 mail@bihl-wiedemann.de page Mannheim, 6..6 We reserve the right to change any data

5 Cable Duct.0 Motor Modules Bit assignment BW90, BW89 Data bit Function DI0 I input I DI I input I DI I state (motor fault) motor DI I state (motor fault) motor DO0 O start/stop motor DO O direction of rotation motor DO O start/stop motor DO O direction of rotation motor Connections M8 BW89 Pins Connection Name / Number Cable length O I analog value M (motor ) (0: 0 V; : V) (0: 0 V; : V) O, cm V ext out 0V O ext out I analog value M (motor ) (0: 0 V; : V) (0: 0 V; : V) O I I 7, cm V out of 0V out of I I in, cm V ext in V ext in 0V ext in 0V ext in in out 0 cm Connections M8 BW90 Pins Connection Name / Number Cable length O I analog value M (motor ) (0: 0 V; : V) (0: 0 V; : V) O, cm V ext out 0V O ext out I analog value M (motor ) (0: 0 V; : V) (0: 0 V; : V) O I I 7, cm V out of 0V out of I I (brown) (blue) (brown) (blue) and via profile cable. The cable length between motor module and passive distributor is cm. Accessories: for BW89: - passive distributor (article no. BW76) for BW90: - connecting cable for addressing with a hand held address programming device (article no. BW0) - connecting cable for addressing with gateways (article no. BW0) Bihl+Wiedemann GmbH Floßwörthstr. D-6899 Mannheim Phone: (+9) 6/996-0 Fax: (+9) 6/99 mail@bihl-wiedemann.de We reserve the right to change any data Mannheim, 6..6 page