axcs Magellan CMU Installation, Operation and Care Manual

Transcription

1 axcs Magellan CMU Installation, Operation and Care Manual

2 Table of Contents Section I Introduction Introduction... 2 Specifications... 3 Basic Components Section II Pre-installation Utility Service Center... 6 Plumbing Contractor's Procedure... 6 Electrical Contractor's Procedure... 7 USC Base... 7 Section III Installation Magellan Unit Support Umbilical Assembly Magellan Unit Post Delivery Head Handpiece Tubing Syringe Tubing Delivery Head Tray with Pad Clean Water System (Optional) Water Heater (Optional) Assistant's Arm (Optional) Basic Electrical Box (Optional) Power Module (Optional)...19 Fiber Optics Electrical (Optional) Fiber Optic Tubing (Optional) Light or Monitor Pole (Optional) Chipblower (Optional) Finalizing USC Installation Reprogramming Chair Section IV Testing Utility Service Center Handpieces Optional Features Installation, Operation and Care Manual Section V Operation Delivery Head Handpieces Syringe...32 Foot Control...32 Clean Water System (Optional) Chipblower (Optional) Fiber Optics (Optional) Assistant s Vacuum Accessories Section VI Care Cleaning Disinfecting Section VII User Service Information Delivery Head Handpiece Arm System Water Heater...38 Service Instruction Section VIII Parts List / Diagrams Utility Service Center Power Module...40 Assistant's Arm...41 Fixed/Adjustable Arm...42 Traditional Delivery Head...43 Euro-Style Delivery Head Foot Control...45 Air/Water Syringe HVE Nozzle...46 Saliva Ejector Nozzle...46 Clean Water System...47 Pivot Hardware Product Support Services Basic Electrical Box Wiring Diagram Power Module Wiring Diagram Tubing Diagram Template (USC Base) axcs Magellan CMU 1

3 Section I Introduction axcs Magellan CMU This manual contains installation, operation and care instructions for the DentalEZ axcs Magellan Chair Mounted Unit (CMU). The axcs Magellan is designed to provide troublefree service when installed, operated and maintained according to the instructions in this manual. To ensure correct installation, carefully read all the instructions contained in this manual paying close attention to all notes, cautions and warnings. Before proceeding, please review the illustration below to become familiar with the components of the axcs Magellan. After the Magellan unit is installed, please review the operation procedures and care guidelines with the doctor's staff. Then leave this manual in the doctor's office for the doctor's and staff's future reference. Light Post (Optional) Foot Control Magellan Unit Support Umbilical Utility Service Center Magellan Unit Post Rear Assistant's Arm & Mount (Optional) Delivery Head (Traditional Shown) Adjustable Arm 2 Installation, Operation and Care Manual

4 Section I Introduction Specifications Delivery Head Water Pressure Maximum PSI Air Pressure Maximum... Refer to the appropriate handpiece specifications Utility Service Center Power Supply Voltage Volts 60 Hz. Air Pressure Maximum PSI Water Pressure Maximum PSI Unit Weight Delivery Head...16 lbs. Support Arms...12 lbs. Magellan Unit Support...23 lbs. Assistant's Arm...16 lbs. Clean Water Reservoir Capacity... 1 pint (Optional order Kit # if desired.) (Euro 16-3/4") 18-1/2" 14" (Euro 17") R 24" 22-5/8" 5-1/4" 3-1/2" R 26-1/2" 21-1/4" 27-3/4" 27-3/4" 41-1/4" 13-1/4" 6-5/8" 9-3/4" - 21" 5-1/2" 13" axcs Magellan CMU 3

5 Section I Introduction axcs Magellan CMU The axcs Magellan CMU package includes: Delivery Head (either Traditional or Euro- Style) with Arm Assembly and Umbilical Magellan Unit Post (and Light Post if ordered) Magellan Unit Support Utility Service Center Foot Control Unpacking Cartons The axcs Magellan components are packaged and shipped according to the carton diagrams shown below and on Page 5 NOTE: Be aware that some cartons are shipped as filler and may be empty (even if optional components were ordered) Verify the components packaging contents against the packing list All parts supplied are necessary for proper installation, so be sure not to discard any hardware or components until installation is complete Magellan Unit Post Basic Components axcs Magellan Unit/Light Mount Carton Magellan Unit Light Post (If Ordered) Magellan Unit Support Installation Hardware NOTE: If light post ordered, entire contents will be inside light post box Unit Post/Support Carton Contents: Magellan Unit Post Magellan Unit Support NOTE: If a pre-tubed chair was ordered, items marked with an * will be on the chair Pole Pivot Supply Bag # : NOTE: If light post ordered, another # bag of supplies will be included - Post Pivot Pin - Two Thrust Bearings - Four Thrust Washers - 3/8" x 2-1/4" Hex-head Bolt* - 382/ 393 ID x 683 OD Washer* - 13/32" ID x 13/16" OD Washer* - Socket Set Screw - 1/4-20 x 3/8" Set Screw* - Rubber Pivot Cover Magellan Light Supply Bag # (If light post ordered): - Spacer - #10-32 x 1" Pan-head Screw - Two #10 Internal Tooth Lock Washers - Two 5/16" Heavy Duty Electrical Clamps - #10-32 x 3/8" Pan-head Screw - 7-1/2" Nylon Cable Tie - Light Adaptor Cord Assembly Chair Support Supply Bag # : - Two 3/8-16 x 1" Hex-head Bolt* - Four 13/32 ID x 13/16 OD Flat Washers* - Two 382/ 393 ID x 683 OD Lock Washers* - Four 625" OD x 010" Shim Washers* - 1/2-13 x 2-1/2" Hex Head Bolt* - 1/2" Split Lock Washer* - Two 3/8-16 x 1/2" Hex Set Screw* - Nylon Spacer x 1" Phillips Pan-head Screw - #10 Internal Tooth Lockwasher 4 Installation, Operation and Care Manual

6 Section I Introduction Magellan Unit Supply Bag # : - Post Cover Assembly - Three 4" Nylon Cable Ties - Round Cable Clamp - Six 8" Nylon Cable Ties - 11/16" Closed ID Clamp - 3/8 oz Tube of Lubricant - Three X 5/16" Set Screws - 3/4" x 1-1/2" x 1/16" thick Tape - Two-position Jumper Connector - 14" Nylon Cable Tie axcs Magellan Carton Pre-tube Conversion Supply Bag # : ' x 5/5" ID Spiral Tubing - 5/8" x 5/8" Tubing Connector - Pre-tubed Chair Umbilical - Magellan Mount Cover - Four 8" Nylon Nylon Cable Ties - Four X 3/8" Phillips Pan-head Screws - Three Cable Clamps - 5' x 1-3/4" ID Ducting Hose - Bracket for 1-1/4" Ductile Tubing - Pump Cover Umbilical Slot Template - Light Extension Cord NOTICE For any questions about an order, please contact a DentalEZ Equipment customer service representative at DTE-INFO Utility Service Center Assembly Foot Control & Installation Hardware Traditional Delivery Head Euro-Style Delivery Head Delivery Head (Traditional or Euro-Style) Foot Control Utility Service Center axcs Magellan CMU 5

7 Section II Pre-installation axcs Magellan CMU Utility Service Center USC Carton Contents: Utility Service Center (USC) USC Cover USC Base (Floorplate) Bag of Supplies # : - Four #10 Screws - Four 6-32 x 1/2" Screws - Four 6-32 Nuts - Two Adaptors - Four Plastic Anchors - 1/4" OD Tubing Barb - Plug Cap - Two 1/8" Tubing Clamps - Five 1/4" Tubing Clamps - 3-Pin Connector Housing - Elbow Assembly - Elbow Fitting - Two Coupler Fittings - Air Fitting Assembly - Two 90 Stop Valves - Water Actuator Valve Assembly - Washer - Two #6 x 3/8" Screws (extra) NOTICE Set the USC cover aside until all installation and testing is complete NOTE: The USC umbilical bracket is shipped from the factory attached to the USC base plate 1 Remove the full-size (scaled) USC template found in the back of this manual 2 Position the USC template according to the exact layout indicated, making certain correct distance from base to chair is maintained 3 Using the USC template, drill four corner mounting holes for the USC base But do not secure the base to the floor at this time NOTE: For wood or metal floors, drill 5/32" holes For concrete, drill 1/4" holes and install plastic anchors IMPORTANT NOTICE DO NOT DISCARD the USC template after use Neatly refold it and replace it in the back of this manual WARNING Before proceeding with plumbing and electrical installation, comply with and maintain all applicable utility codes and regulations Plumbing Contractor's Procedure NOTICE For reference, a color-coded tubing diagram is located at the end of this manual 1 Find and open the USC bag of supplies 2 Using the full-size, scaled USC template found in the back of this manual, orient the utilities (as shown in the picture below) and stub through the floor NOTE: Pay close attention to the orientation of the template to the chair NOTE: The 7/8" hole for the gravity drain elbow is not needed for the Magellan unit CHAIR SIDE USC Base Mounting Holes Water Stop Valve Air Stop Valve Vacuum Elbow 6 Installation, Operation and Care Manual

8 Section II Pre-installation 3. Sweat the valve adaptors to the air and water stubs. 4. Apply the appropriate thread sealant to the valve adaptors and install the stop valves. 5. Sweat the vacuum elbow to the stub. Electrical Contractor's Procedure NOTICE Electrical contractor's parts are not supplied. Air Fitting Assembly CHAIR SIDE Water Actuator Valve Assembly The electrical contractor is to provide a covered 115 VAC receptacle which meets all applicable utility codes and regulations. For the recommended location of the 115 VAC receptacle, see the full-size, scaled USC template in the back of this manual. NOTE: If the recommended location is not met, the USC base or the optional power module may interfere with the 115 VAC receptacle. 6. Sweat the hose connector to the elbow as applicable and orient as shown in the photo above. 7. Flush the air and water lines to remove trash and debris from the lines. 8. Connect the water actuator valve assembly to the water stop valve as shown in the photo above. Using a 5/8" open-end wrench, tighten the nut securely. 9. Connect the air fitting assembly to the air stop valve as shown in the photo above. Using a 5/8" open-end wrench, tighten the nut securely. CHAIR SIDE USC Base 115 VAC Receptacle 1. Position the USC base over the four corner holes that were drilled during pre-installation. 2. Secure the base using four #10 screws. NOTICE If previous utilities interfere with the USC base internal bracing, modification may be necessary. axcs Magellan CMU 7

9 Section III Installation axcs Magellan CMU NOTE: The instructions contained in this manual pertain to axcs Chair, J-Chair and V-Chair installation with exceptions noted Photos and illustrations depict axcs Chair installation 1 Magellan Unit Support Raise the base and back to full UP position J-Chair/V-Chair - Raise the seat also 2 Disconnect the chair from the power supply 3 Remove the chair's seat and set it aside with all related hardware To remove the seat: Brake Cover Lower Cantilever Cover axcs Chair - Take off the brake cover by unsnapping the two plastic cover caps and removing the two Phillips-head screws Remove the retaining rings and pins that hold the seat to the chair Then relocate the seat height adjustment rollers from the bottom position (as shipped) to the top position J/V-Chair - Unsnap the four decorator plastic cover caps (two) on the back and (two) on the underside of the chair seat cushion Then remove the four 1/4-20 x 5/8" screws that secure the seat to the chair mount casting Phillipshead Screws Pin Ring Base (Pump) Cover axcs Chair Top Arm Cover Assembly Phillipshead Screws 4 Using a 1/8" Allen wrench, remove the two screws from the chair's lower cantilever cover assembly, then using a Phillips-head screwdriver, remove the four screws from the chair base cover Take off both covers and set them aside with their related hardware *IMPORTANT NOTE: This manual contains instructions for installing an axcs Magellan Unit on a pre-tubed or non-pre-tubed chair Pre-tubed chairs have an umbilical assembly running along the top casting through the cantilever and out the base (pump) cover, and the Magellan Unit mount is pre-installed at the factory If installing the Magellan Unit on a chair that is not pre-tubed, use conversion kit # and continue with the instructions below If installing on a pre-tubed chair, skip Steps 5-11 *5 Select the following items from the Magellan unit support hardware package: 1/2" x 2-1/2" Bolt 1/2" Lock Washer Two 3/8" x 1" Bolts Two 3/8" Flat Washers & Lock Washers Four 3/8" x 01 Shims** Plastic Spacer *6 Determine if the two 3/8" threaded hole mounting pads and the Magellan Unit support are level If the mounting pads or unit support are not level, select the necessary amount of 3/8" shims needed to provide a level condition across the two pads Chair Mount Casting Yardstick 3/8" Threaded Hole Mounting Pads Level 8 Installation, Operation and Care Manual

10 Section III Installation 1/2" Bolt Chair Mount Casting Thick/Thin Shim Washers (as needed) Magellan Unit Support 3/8" Flat Washer 3/8" Lock Washer 3/8" Bolt 1/2" Lock Washer /8" bolts to allow a 3/16" clearance at the 1/2 bolt location, then adjust the 3/8" set screws until the unit support is level Tighten all hardware: 22 foot-pounds for 3/8" bolt 55 foot-pounds for 1/2" bolt Using the #10 screw and lock washer, install the plastic spacer on the top surface of the Magellan unit support Umbilical Assembly *7 *8 Position the Magellan unit support so that the two 3/8" and one 1/2" through holes align with the corresponding threaded holes of the chair mount casting Install the two 3/8" bolts, flat and lock washers and the number of 3/8" shims determined in Step 6 through the Magellan unit support and tread into the chair mount casting *9 Tighten both 3/8" bolts to allow a 3/16" clearance at the 1/2" bolt location *10 *11 12 Install the 3/8" set screws in the bottom of the Magellan unit support Install the 1/2" lock washer and 1/2" bolt, but do not fully tighten Place a level on the Magellan unit support, parallel with and perpendicular to the chair center line Then check the level of the unit support If leveling adjustment is necessary, first loosen the 1/2" bolt, next loosen the 1/2" Bolt & Lock Washer Spacer, #10 Screw & Lock Washer Level (parallel) *IMPORTANT NOTE: If installing on a pre-tubed chair, skip Steps 1-18 *1 Select the following hardware items: Six 8" Tie Wraps Three 4" Tie Wraps 3/4" x 1-1/2" Foam Pressure Tape Two 1" Plastic Clamps Two 5/8" Metal Clamps 5' x 1-3/4" Corrugated Ducting Hose 8-1/2' x 5/8" Chair Umbilical Assembly Vacuum Hose & 5/8" x 5/8" Connector *2 Route and secure the chair umbilical as follows: NOTE: The chair umbilical end containing the most connectors remains on the top side of the chair Pass the other end through the chair pivot opening axcs Chair - Route the chair umbilical assembly under the rod-end port of the back support lift cylinder Using two 8" tie wraps, secure the umbilical assembly as shown in the illustration Touch Pad Wire Umbilical Assembly Clamp Set B 3/8" Set Screws (for leveling) 3/8" Bolts Magellan Unit Support White Cable 8" Tie Wrap Clamp Set A axcs Chair axcs Magellan CMU 9

11 Section III Installation axcs Magellan CMU J/V-Chair - Route the chair umbilical assembly through the front slot in the chair casting and continue as shown in the illustration below Then secure using the two 1" plastic clamps and tie wraps Lift Cylinder Hydraulic Hoses Syringe Air/ Water Lines Clamps Casting Slot Touchpad Wire White Cable Umbilical Assembly Tilt Cylinder Assembly J/V-Chair NOTE: Avoid the tilt cylinder assembly because it moves and could cut or pinch the tubing NOTE: Make sure the umbilical assembly exhibits a small amount of slack when the Magellan unit post is aligned with the chair NOTE: Remove only the rear portion of cable wrap on the umbilical assembly to expose the protective foam block at the touch pad wire connector *3 Remove and discard the two existing 3/8" black clamps at clamp set A and B Then install the two 5/8" metal clamps on the umbilical assembly at the same locations *4 axcs Chair - Place an 8" tie wrap behind clamp set B Then wrap the tie around the hydraulic hose and umbilical and secure *5 axcs Chair - Trim the end of the tie-wrap and rotate the tie wrap's head so it is positioned in an open area HELPFUL NOTE: Positioning the back of the seat forward will make Step 6 easier *6 Route the umbilical assembly through the pivot opening along with the other hoses *7 Place the umbilical assembly on the underside of the chair lift as shown in the photo above in the next column Umbilical Assembly Tie Wraps 5/8" Vacuum & 5/8" x 5/8" Connector NOTE: Make certain the umbilical assembly is not contacting the electrical wiring within the power assembly area *8 Use two 4" tie wraps to secure the umbilical to the hydraulic hoses *9 Remove the power cord restraint from the L- shape bracket on the chair pump assembly *10 Remove the hospital plug from the chair power cord and take note of the wire color of the cord to the corresponding screw color of the plug *11 Slide the power cord restraint off the power cord and set aside Umbilical Old Bracket New Bracket *12 Thread the 5' x 1-3/4" ducting hose (left-hand threads) on the painted bracket of the chair's pump assembly NOTE: It may be necessary to replace the existing chair's pump assembly bracket with the one containing 10 Installation, Operation and Care Manual

12 Section III Installation a larger diameter hole which is provided in the pretube conversion kit *13 Place the 8-1/2' x 5/8" vacuum hose onto the underside of the chair Use two 8" tie wraps, and attach the vacuum hose to the inside of the cantilever arm (See photo at top of Page 10 ) *14 Route the 8-1/2' x 5/8" vacuum hose under the chair's pump assembly *15 Feed the chair umbilical assembly and the 8-1/2' x 5/8" vacuum hose into the 5' x 1-3/4" corrugated ducting hose *16 Obtain the chair pump cover slot template (PN: B) included with the pre-tube conversion kit and follow the instructions to route out the power cord slot Screws & Tape Template Rotary Cutting Tool Ducting Hose USC Base #10 Screw Holes L-Shaped Bracket 20 Remove the two #10 screws that secure the L-shaped bracket to the USC base plate 21 Thread the L-shaped bracket onto the 1-3/4" ducting hose that connects the chair to the USC (The ducting hose is left-hand threaded ) NOTE: It may be necessary to trim the 1-3/4" ducting hose and umbilical tubing passing through it It is recommended not to trim the umbilical wires, but rather coil them inside the USC 22 Reattach the L-shaped bracket onto the USC base using the two #10 screws Magellan Unit Post *17 Position the base (pump) cover to align the four mounting holes to ensure the chair's umbilical assembly does not interfere with the cover's fit But, do not secure the base (pump) cover at this time *18 Pass the power cord through the 5' x 1-3/4" corrugated ducting hose and into the USC 19 Trim the power cord length if desired (If installing on a pre-tubed chair, first remove the hospital plug from the chair power cord and take note of the wire color of the cord to the corresponding screw color of the plug ) Trim off the excess cord, then reattach the hospital plug to the cord 1 Select the following hardware package items: 3/8" x 2-1/4" Hex-head Screw 1/4", 3/4" and 3/8" Set Screws (one each) 3/8" Flat and Lock Washers (one each) Four Thrust Washers Two Thrust Bearings Rubber Cap Tube of Lubricant Post Pivot 2 Place a thrust washer on the 2" diameter bearing surface of the Magellan unit support 3 Apply lubricant to a thrust bearing and install the bearing, followed by a second thrust washer 4 Position a thrust washer onto the flat member of the Magellan unit post axcs Magellan CMU 11

13 Section III Installation axcs Magellan CMU Rubber Cap Post Pivot Pin Thrust Washers Unit Pole Thrust Bearing Unit Support 1/4-20 x 3/4" Set Screw 3/8" Hex-head Bolt 3/8" Lock Washer 3/8" Flat Washer Slot 1/4-20 x 3/8" Set Screw 5 Apply lubricant to the second thrust bearing and install followed by a thrust washer 6 Position the support post so that the 1-1/4" I D brass bushing in the flat member is aligned with the bearing stack HELPFUL NOTE: Grasping the unit post with one hand so that the unit post flat member bears against the top lug of the unit support will assure the alignment of the thrust bearing is maintained 7 Using a free hand, insert the pivot mount with thrust bearing and washers through the 1-1/4" diameter bore and the lower bearing stack Then engage the pivot mount into the brass bushing NOTE: Engagement is a slip fit, provided the Magellan unit post is held in alignment CAUTION To avoid damage to the pivot bushing, do not use force when installing the pivot mount into the Magellan unit post 8 Make sure the pivot pin slot faces the side of the unit support having the tapped hole 9 Seat the pivot mount until its head is in full contact with the bottom and sides of the Magellan unit support 10 Locate the 1/4" x 3/4" long set screw in the threaded hole on the Magellan unit support Then tighten the 1/4" x 3/4" set screw to prevent the pivot pin from rotating 11 Place a 1/4" x 3/8" long set screw into the threaded hole in the flat member of the Magellan unit post 12 Engage the 1/4" x 3/8" set screw with a 1/8" Allen wrench to deform the internal bushing against the pivot mount until a 3-pound force is required to rotate the unit post 13 Install the rubber cap over the bolt head Delivery Head 1 Select the following hardware items: Three #10 Set Screws Tube of Lubricant (used earlier) 2 Remove the packaging from the delivery head along with the adjustable arm and the umbilical assembly 3 Apply lubricant to the inside bore of the Magellan unit post Apply Lubricant Unit Post 4 Feed the umbilical assembly into the unit post, ensuring that the leading end of the umbilical assembly (with the protective spiral end) does not catch on the open access slot or weld seam of the unit post s flat joint 5 After the umbilical assembly is completely installed in the unit post, engage the bearing arm support assembly into the post 6 Align the stop of the bearing arm support with the tapped holes of the unit post and the post s access slot (See illustration next page ) 12 Installation, Operation and Care Manual

14 Section III Installation Bearing Arm Support Assembly Stop Set Screw Tapped Holes #10-30 Screws Mount Cover Chair Umbilical Magellan Post Umbilical J/V-Chair Access Slot 7 Using a 3/32" Allen wrench, secure location with three #10 set screws 8 Remove the two Allen-head screws from the adjustable arm cover and take off the cover Allen-head Screw Pivot Pin Adjustable Arm Cover Spacer 9 Slightly depress the adjustable arm below horizontal to relieve the pressure on the spacer in front of the pivot pin 10 Pull the spacer down approximately 1/2" 11 Let the arm rise above horizontal and remove the spacer completely 12 Remove the red tie wire from the arm brake inside the adjustable arm 13 Replace the adjustable arm cover 14 Match and connect the tubes and wires from the magellan arm umbilical assembly to the tubes and wires of the chair umbilical assembly 15 Place the mount cover on the magellan mount and attach the cover using the four #10-30 screws NOTE: The J/V-Chair has a one-piece, v-shape cover The axcs Chair has a two-section, mirror-image cover 16 Find the touch pad wire at the rear of the chair mount casting and follow the instructions provided with the touch pad NOTE: Provide sufficient slack in the umbilical assembly to avoid stretching when the chair is in its full UP position Standard Tubing Traditional Head Handpiece Tubing 1 Align the female tube connectors to the male tube connectors Then press the connectors together ensuring the alignment pin engages the hole in the unit head chassis 2 Fit the tabs of the tubing cover to engage in the chassis 3 Press firmly to seat the connector Then twist the tubing cover counterclockwise to securely lock it into the chassis 4 Hang the handpiece tubing coupler in the holder axcs Magellan CMU 13

15 Section III Installation Euro-Style Head 1. Slip the arm tube containing the handpiece tubing over the end of the whip arm return mechanism. NOTE: The holder on the left is dedicated to the syringe, but any of the remaining three holders may be used. 2. Install the furnished #4 screw in the screw hole on the underside of the tube. 3. Make sure handpiece tubing is not twisted and insert the tubing into the small rectangular opening on the underside of the chassis. 4. Route the tubing under the arm return bracket to meet the proper tubing coming from the valve block. NOTE: The numbers on the bracket should match those on the chassis next to the valve block. 5. Carefully insert the matching connectors into the proper tubings and twist tightly. 6. After each handpiece tubing assembly is installed, make sure nothing interferes with the cover. 7. Return the cover to its closed position. 8. Place the handpiece connector in the matching groove in the cover (near the upper end of the groove). 9. Move the whip arm to the low position (over the top of the delivery head cover). 10. Adjust the short length of tubing between the bottom of the whip arm and the unit head chassis until the tubing lies loosely against the chassis. Traditional Head axcs Magellan CMU Syringe Tubing 1. Disengage the tubing pinch clamp from the air and water lines inside the unit head. Clamp 2. Hang the syringe valve in the holder. 3. Connect the air and water lines to the appropriate male to female connectors on the unit chassis. Air Line Water Line 4. Connect the syringe to the valve body and install the nozzle tube assembly, following the instructions in owner s manual supplied with the syringe. Euro-Style Head 1. Slip the arm tube containing the syringe tubing over the end of the whip arm return mechanism at the far left. NOTE: The holder on the far left is reserved for the syringe assembly. 2. Install the furnished #4 screw in the screw hole on the underside of the tube. 14 Installation, Operation and Care Manual

16 Section III Installation 3 Insert the end of the tubing into the rectangular hole on the underside of the chassis Then route the tubing under the arm return bracket to meet the two syringe connectors NOTE: The air and water connectors will fit in their proper mating connectors 4 Tightly twist the connectors and make sure they are secure 5 As with the handpiece tubing, bend down the tab attached to the bracket so the syringe tubing holds in place 6 Close the cover Then place the syringe in the mating groove Clean Water System (Optional) NOTE: If the access cover is installed on the delivery head post, remove and retain the two #8 screws that secure it to the post Then take off the cover 1 Pull the 1/4" green tube (the length before the Y connector) through the access slot of the support post 2 Pull the free end of the short 1/8" yellow tube through the access slot of the support post NOTE: When placed, the syringe should extend beyond the end of the groove by the length of the syringe tip This can be adjusted later to suit each doctor 7 Move the whip arm to the low position (over the top of the delivery head cover) 8 Adjust the short length of tubing between the bottom of the whip arm and the unit head chassis until the tubing lies loosely against the chassis Access Slot Green Tube Cut Tube Here Support Post Temporary Tape Short Yellow Tube Remove Plug NOTE: After the tubing installation is complete, open the cover and make sure the tubing is properly connected and does not interfere with the cover Delivery Head Tray with Pad Traditional Head 1 Place the pad on top of the delivery head 2 Position the pad until the tray can center properly 3 Place the tray on the pad Euro-Style Head 1 Place the pad on the tray holder 2 Place the tray on the pad HELPFUL NOTE: Before cutting the green tube, use tape to temporarily attach the section labeled W to the post This will prevent the green tube from falling down into the post and becoming out of reach 3 Cut the green tube midway between label 1 and label W 4 Remove the plug from the yellow tube 5 Obtain the male and two female quick connect couplings provided with the clean water system kit NOTICE For tubing connections, see the tubing diagram in the back of this manual axcs Magellan CMU 15

17 Section III Installation axcs Magellan CMU Male Quick Connect Coupling 6 7 Attach the male quick connect coupling to the green tube labeled 1 Attach the female quick connect couplings to the green tube labeled W and the yellow tube Yellow Tubing Green Tubing Clean Water System Female Quick Connect Couplings 8 Connect the 1/8" green tubings from the clean water system to the green tubings from the support post 9 Connect the 1/8" yellow tubing from the clean water system to the yellow tubing from the support post 10 Reposition the tubings back into the support post taking care not to damage or kink the tubings 11 Attach the clean water system to the support post using the two #8 screws from the cover Water Heater (Optional) NOTE: Please refer to the instructions provided with the water heater Carton Part Contents: Assistant s Arm Tubing Retainer Bracket Mounting Bracket Assembly High-volume Evacuator Valve Handle Saliva Ejector Valve Handle Plastic Strain Relief Bushing (for older chair) Replacement Brake Handle Cover (if needed) Four Solids Collector Traps Hardware: 4' x 1/2" High-volume Evacuator Tubing 4' x 1/4" Saliva Ejector Tubing Two 5/16" Countersink, Socket-head Bolts Two #10 Screws (extra) Two Tie Straps (extra) 1 If the lower cantilever cover is on, take it off by removing the two screws from the underside of the cover 2 Remove the solid-cap plug from the upper cantilever cover and replace it with the supplied strain relief bushing 3 If the brake handle cover is on, take it off by removing the two screws that secure it 4 Using the two 5/16" countersink, socket-head bolts, attach the mounting bracket to the chair Bracket Assistant's Arm (Optional) Countersink Bolts 5 Using a 3/16 Allen wrench and a 9/16 wrench, unscrew the decorative socket bolt from the bracket leaving one of the plastic washers on the mounting bracket 16 Installation, Operation and Care Manual

18 Section III Installation Bracket Washer Washer Nut Decorative Socket Bolt Link 6 Reinstall the brake handle cover Or, install the replacement brake handle cover, which contains a slot for the mounting bracket 7 Place the link of the rear assistant s arm on top of the bracket and plastic washer 8 Put the other washer on the decorative bolt and insert the bolt through the link 9 Thread the bolt into the bracket and tighten the bolt making sure the bolt is sufficiently secure but still allows rotation 10 From the underside of the bracket, install the nut on the decorative socket bolt While holding the decorative socket bolt with a 3/16 Allen wrench, tighten the nut using a 9/16 wrench 11 Using the two #10 screws provided, attach the tubing retainer bracket to the switch bracket (Already installed on the pre-tubed chair ) 13 Pass the tubing and wires through the tubing retainer bracket 14 Connect the 5/8" ID vacuum hose of the rear assistant's arm to the 5/8" ID vacuum hose of the chair by sliding it over the connector of the chair's ducting hose (Refer to photo on Page 10 ) 15 Cut off excess vacuum tubing Then secure the ducting hose neatly to the inside of the chair's cantilever using the supplied tie straps This will prevent the tubing and wires from going beyond the tubing retainer bracket and being pinched or cut Allow enough slack for chair movement NOTE: Complete syringe tubing connection instructions are on Page 18 NOTE: For connection reference purposes, a full-color tubing diagram is located in the back of this manual 16 Place the assistant's arm in its normal operating position and make sure the bottom portion of the assistants's arm is level NOTE: If leveling is needed, tilt the arm up to expose set screw in the leveling plate and adjust the leveling set screw as necessary Leveling Plate Tubing Strain Relief Bushing Leveling Set Screw Switch Bracket Tubing Retainer Bracket #10 Screws 12 Pass the tubing and wires from the assistant's arm through the strain relief bushing in the cantilever cover Assistant's Arm Touch Pad Controller (Optional) If installing the optional touch pad controller on the assistant's arm for the axcs chair, J-Chair or V-Chair, please refer to the Installation Instructions included with the controller axcs Magellan CMU 17

19 Section III Installation axcs Magellan CMU Saliva Ejector 1. Connect the saliva ejector valve to the 5/16" saliva ejector tubing. 2. Hang the saliva ejector valve in the instrument holder. 3. Connect the tubing to the open 1/4" port under the solids collector in the assistant's arm. High-Volume Evacuator (HVE) 1. Connect the HVE valve to the 1/2" tubing. Saliva Ejector Valve Closed 1/2" Port Instrument Holder HVE Valve 2. Hang the HVE valve in the instrument holder. 3. Connect the tubing to an open 1/2" port under the solids collector in the assistant's arm. 4. If an optional second high-volume evacuator valve is used, do the following: a. Insert a sharp, pointy object into the closed 1/2" 1/2" HVE Tubing port under the solids collector and create a smooth opening. b. Repeat Steps 1 through 3. Air/Water Syringe (Optional) 1. Pass the twin 1/8" syringe tubing from the assistant's arm through the top cantilever cover opening, routing it through the chair to the umbilical assembly located under the cantilever cover. (See the tubing diagram in back of this manual and refer to the photo on Page 14.) 2. Find the 1/8" yellow, plugged tubing marked A in the umbilical assembly located near the tubing retainer bracket. This 1/8" yellow tube is paired with a 1/8" clear, plugged tube marked W. Both tubes are held together with a plastic pinch clamp. 3. Remove the plastic pinch clamp and cut the plugged ends off both A and W tubes. 4. Place a 1/8" male quick-connect fitting on the yellow A tube and a 1/8" female quickconnect fitting on the clear W tube. 5. Cut the twin 1/8" syringe tubing to a length suitable to connect to the A and W tubes. 6. Place a 1/8" male quick-connect fitting on the 1/8" non-ribbed syringe tubing and a 1/8" female quick-connect fitting on the ribbed syringe tubing. 7. Join both sets of male/female connectors. NOTE: Refer to the tubing diagram in the back of this manual if necessary. 8. Connect the syringe to the valve body and install the nozzle tube assembly following the instructions in the supplied syringe manual. 9. On the underside of the assistant's arm housing, connect the male and female quick connect fittings to the syringe. Syringe Air/ Water Quick Connects 10. Hang the syringe in the instrument holder. 18 Installation, Operation and Care Manual

20 Section III Installation Basic Electrical Box (Optional) 1. Unplug all cords from the receptacle in the USC. NOTE: See the basic electrical box system wiring diagram in the back of this manual for connections. Power Module (Optional) 1. Unplug all cords from the receptacle in the USC. NOTE: See the power module system wiring diagram in the back of this manual for connections. Green Ground from Main Harness Green Ground from Adaptor Harness Umbilical 1/8" Barb 1/8" Yellow Tube Main Harness Valve Assembly Main Harness Basic Electrical Box Adaptor Harness Power Module Green Ground from Main Harness Adaptor Harness 2. Connect the supplied adaptor harness to the main wiring harness. 3. Connect the green wire of the adaptor harness to the USC base or electrical box to ground it. NOTE: The adaptor harness has two connectors: One will connect to the fiber optic transformer (if ordered). The other will connect to the light transformer (if ordered). Both transformers plug into the basic electrical box. 4. Pass the green ground wire of the main harness through the umbilical and ground it to the chair. NOTE: It may be necessary to remove an existing screw and reinsert the screw with the green ground wire attached. 2. Connect the main wiring harness to the power module. 3. Using the tube clamps supplied, connect the 1/8" yellow air line from the valve assembly to the 1/8" barb on the power module. Then disengage the pinch clamps. 5. After checking all the plug connections, reconnect the power plug into the receptacle in the USC. 4. Pass the green wire of the main harness through the umbilical and ground it to the chair. NOTE: It may be necessary to remove an existing screw and reinsert the screw with the green ground wire attached. NOTE: Make sure the air valve in the USC is open. 6. At the delivery head, turn the master switch to ON and ensure power is available at the power module. axcs Magellan CMU 19

21 Section III Installation axcs Magellan CMU Fiber Optics-Electrical (Optional) NOTE: For fiber optics electrical connections, see the basic electrical box or power module system wiring diagrams in the back of this manual. Traditional Head 1. Lift the delivery head lid to reach the internal components. 2. Slide the black and white electrical wire leads from the lamp controller through the hole in the underside of the delivery head. 5. Make internal electrical connections: black to black; white to white. 6. Cut off the tubing plugs on the clear 1/8" air signal tubings and connect the corresponding tubings to the air switch barbs marked with numbers 1, 2 and 3 inside the unit head. 7. Install the terminal pins existing on the black and white wires into the 3-position housing located at the end of the umbilical assembly. 1 3 Black White Lock washers Fiber Optic Control Assembly 3. Align the three air switch barbs and insert the barbs through the three holes in the unit head chassis. 4. Using four #6-32 screws and lock washers provided, attach the fiber optic lamp control assembly to the unit head chassis. Screws Clear Tubings 8. Insert the black wire pin into the #1 position of the plastic pin connector. 9. Insert the white wire pin into the #3 position of the pin connector. 10. In the USC, plug the black and white wire leads from the umbilical into the orange and yellow wires of the main wiring harness. NOTE: If the optional power module was installed, installation of the fiber optics electrical system is complete. If the power module was not ordered, proceed to Step Plug the supplied adaptor wiring harness into the main wiring harness. NOTE: If the power module was not ordered, the unit is equipped with a power pack transformer. Air Switch Barb Wire Leads Fiber Optic Control Assembly Ground Power Pack Transformer Main Harness Adaptor Harness 20 Installation, Operation and Care Manual

22 Section III Installation 12. Plug the connector end of the power pack transformer into the yellow and orange wires of the adaptor wiring harness. 13. Plug the power pack transformer into the basic electrical box. Euro-Style Head 1. Raise the rear of the delivery unit head cover and lift the cover gently over the front of the unit until the cover lies flat. This will give free access to the internal components. NOTE: To eliminate the possibility of bending the hinge, use care not to force the cover down. 2. Line up the three air barbs from the fiber optic controller with the larger holes in the chassis. Then slip the electrical wires through the matching holes on bottom of the unit head chassis. 3. Attach the fiber optic unit to the chassis using the four #6-32 screws and lock washers provided. 4. Connect the fiber optic wires to the mating wires in the unit head, color match the wires. 5. Cut off the tubing plugs on the clear 1/8" air signal tubings coming from the valve block and connect the tubings to the air switch barbs with corresponding numbers. 6. For power connection, refer to Fiber Optics-Electrical, Traditional Head, Steps 7 through Check to ensure all connections are firm. 8. Close the delivery unit head cover. CAUTION Make certain no leads or tubings interfere with closing the cover or any other part of the unit. Fiber Optic Tubing (Optional) Traditional Head 1. Slide the fiber optic electrical lead through the hole in unit head chassis. Then plug the lead into the appropriate fiber optic controller electrical outlet marked 1, 2 or 3. Alignment Pin Electrical Lead Tubing Cover 2. Align the female tube connectors to the male tube connectors. Then press the connectors together ensuring the alignment pin engages the hole in the unit head chassis. 3. Fit the tabs of the tubing cover to engage in the chassis. 4. Press firmly to seat the connector. Then twist the tubing cover counterclockwise to securely lock it into the chassis. 5. Hang the handpiece tubing coupler in the holder. Euro-Style Head 1. Slip the arm tube containing the fiber optic handpiece tubing over the end of the whip arm return mechanism. NOTE: The holder on the left is dedicated to the syringe, but any of the remaining three holders may be used. axcs Magellan CMU 21

23 Section III Installation 2. Install the furnished #4 screw in the screw hole on the underside of the tube. 3. Make sure handpiece tubing is not twisted and insert the tubing into the small rectangular opening on the underside of the chassis. 4. Route the tubing under the arm return bracket to meet the proper tubing coming from the valve block. NOTE: The numbers on the bracket should match those on the chassis next to the valve block and at the fiber optic air switch barbs. 5. Carefully insert the matching connectors into the proper tubing and twist tightly. 6. Insert the electrical bayonet connector into the matching socket. 7. After each handpiece tubing assembly is installed, make sure nothing interferes with the cover. 8. Return the cover to its closed position. 9. Place the handpiece connector in the matching groove in the cover (near the upper end of the groove). 10. Move the whip arm to the low position (over the top of the delivery head cover). 11. Adjust the short length of tubing between the bottom of the whip arm and the unit head chassis until the tubing lies loosely against the chassis. axcs Magellan CMU Light or Monitor Pole (Optional) 1. Select the following items from the hardware package: 3/8"-16 x 2-1/4" Hex-head Bolt 1/4" x 3/4" Set Screw 1/4" x 3/8" Set Screw 3/8" Flat and Lock Washer (one each) Four Thrust Washers Two Thrust Bearings Rubber Cap Tube of Lubricant Post Pivot 2. Raise the chair base to its upper travel limit and disconnect the chair power. 3. Remove the warning tag from the unit post assembly and set the assembly aside for use when reprogramming the chair. 4. Apply lubricant to the pivot pin shaft and both sides of all thrust washers and thrust bearings. 5. Place a thrust washer, bearing and another thrust washer onto the pivot pin. Then insert the pivot pin and bearing stack through the 1-1/4" brass bushing at the end of the light/ monitor pole. Place another thrust washer, bearing and thrust washer onto the pin. Thrust Washers 1/4" x 3/8" Set Screw 1/4" x 3/4" Set Screw Align pin w/pivot pin Counter Bore Thrust Bearing 1-1/4" Brass Bushing Light Arm or Note Slot Orientation Monitor Arm Pivot Pin 3/8" Flat Washer 3/8" Lock 3/8" x 2-1/4" Bolt Washer Rubber Cap 22 Installation, Operation and Care Manual

24 Section III Installation 6. While holding the bearings and pin in the pole, align the machined hole in the pivot pin with the pin in the chair support's bottom counter bore. Then adjust the unit pole and pin so the pin will slide into the counter bore. NOTE: Engagement is a slip fit, provided the Magellan light/monitor pole is held in alignment. CAUTION To avoid damage to the pivot bushing, do not use force when installing the pivot mount into the light/monitor pole. 7. Seat the pivot mount until its head is in full contact with the bottom and sides of the Magellan unit support. 8. Make sure the pivot pin slot faces the side of the unit support having the tapped hole. 9. While holding the unit pole in position, install the 3/8"-16 x 2-1/4" hex-head bolt with 3/8" lock and flat washers through the pin so that it threads into the chair support. Then tighten the bolt enough to remove most clearances between the bearings. 10. Install the 1/4" x 3/4" set screw into the threaded hole on the Magellan unit support. Then tighten the set screws to prevent the pivot pin from rotating. 11. Finish tightening the bolt in the pin until all the clearance between the bearings is removed and the pole moves freely. Then retighten the set screw. 12. Place a 1/4" x 3/8" set screw into the threaded hole in the flat member of the Magellan unit post. 13. Engage the set screw with a 1/8" Allen wrench to deform the internal bushing against the pivot mount until a 3-pound force is required to rotate the unit post. 14. Install the rubber cap over the bolt head. NOTICE For complete light pole installation instructions, refer to the axcs Operatory Light (Post Mount) Manual, PN Monitor Pole Completion 1. Assemble the components of the monitor tray and arm as shown in the photo below. Hole Plug Bolt Tray Arm 1/4" ID Nut (Left Hand Thread) 2. Pass the bolt through the tray, plastic spacer and arm. 3. Secure the bolt using the 1/2" ID threaded nut. Then screw the 1/4" ID threaded nut on the bolt to lock it in place. NOTE: The 1/4" ID nut has left hand threads. 4. Place the tray/arm assembly over the monitor pole. 5. Use the supplied set screw to hold the tray/ arm assembly in place. Monitor Pole Tray Spacer End Cap 1/2" ID Nut Set Screw Hole Tray/Arm Assembly axcs Magellan CMU 23

25 Section III Installation axcs Magellan CMU Chipblower (Optional) CAUTION Before installing the chipblower, make sure the unit is turned OFF so no air is present at the foot control. 9. Install the chip air valve assembly on the foot control base. 10. Secure the chip air valve assembly using the three flat-head screws included in the kit. 11. Connect a three-inch section of tubing to the B port of the shuttle valve and to the chip air valve. 1. Confirm that the unit master switch is OFF. 2. Remove the seven flat-head screws from the base of the foot control. 3. Disassemble the foot control as shown in the illustration below. 6" Clear Tubing Tee Wet/Dry Toggle Valve 3" Tubing Drive Air Valve Chipblower 6" Tubing Shuttle Valve Chip Air Valve Assembly Flat-head Screws 4. On the foot control tubing, remove the chip air line from the tee fitting. 5. Secure all the connections using the tubing clamps provided. 6. Connect a six-inch section of the clear 1/8" tubing included in the kit to the tee fitting. 7. Rotate the tubing around the drive air valve as shown in the illustration above. 8. Attach the clear 1/8" tubing to the A port of the shuttle valve. 12. Attach the chip air line on the foot control tubing to the C port of the shuttle valve. 13. Remove the hex plug from the drive air valve. 14. Place a plastic washer on the threaded end of the barb fitting. 15. Install the fitting into the drive air valve. 16. Route a six-inch section of tubing from the drive air valve to the remaining barb on the chip air valve assembly. 17. Reassemble the foot control. 18. Replace the seven flat-head screws. 24 Installation, Operation and Care Manual

26 Section III Installation Finalizing USC Installation NOTE: See the tubing diagram in the back of this manual for all connections. 1. Select the following hardware items: Six 1/8" Tubing Clamps Three 1/4" Tubing Clamps Foot Control Leads (4) B A Chair Umbilical 2. Remove the cable wrap to expose the tubing connections of the umbilical assembly. NOTE: If the pump cover and the chair's lower cantilever cover are not already removed, take them off now. (Refer to Page 8, Step 4.) 3. Starting from the back of the chair, route the foot control tubing under the chair's top cantilever cover. 4. Find the foot control leads of the chair's umbilical assembly numbered 1, 2, 3 and 4 located toward the rear of the chair's pump motor assembly. 5. Attach the 1, 2, 3 and 4 leads with the corresponding numbered connectors of the foot control tubing. 6. In the USC, attach the hard, red air line to the air valve fitting using the supplied compression fitting. (See connection A.) 7. Attach a 1/4" tubing clamp to the rigid 1/4" green water line of the water regulator. (See connection B.) 8. Use soap to lubricate the 1/4" barb. Then connect the water line to the water valve/ actuator. 9. Connect the 1/8" red tube from the umbilical to the poppet valve connection opposite the existing barb assembled to the 1/4" red tube. (See connection C.) 10. Connect the 1/8" yellow tube from the umbilical to the poppet valve connection opposite the existing barb assembled to the 1/8" yellow tube. (See connection D.) 11. Connect the 1/4" red tube, numbered 1, to the middle barb of the poppet valve in the USC. Then secure the connection using a 1/4" tubing clamp. (This is the drive air line for the foot control.) (See connection E.) C E D axcs Magellan CMU 25

27 Section III Installation axcs Magellan CMU Power Module 1/8" Yellow Line K G 12. Connect the 1/4" green tube of the umbilical to the connector from the 1/4" green tube of the water regulator. (See connection F.) 13. Attach a 1/8" tubing clamp to the 1/8" yellow air line of the poppet valve. 14. Use soap to lubricate the barb of the water valve actuator. Attach the 1/8" yellow line of the poppet valve to this barb and secure using a 1/8" tubing clamp. (See connection G.) 15. If a rear assistant's arm is installed, slip the vacuum hose from the chair over the vacuum elbow in the USC. (See connection H in photo on Page 25.) 16. If an optional fiber optic electrical system is installed, attach the electrical leads of the power pack transformer with connection J. (Refer to Page 20 for details.) F H NOTE: If equipped with a power module, an extra tee must be spliced into this 1/8" yellow air line between the poppet valve and water valve actuator. Then connect the open end of the tee to the barb of the power module using a section of 1/8" yellow air line and two tubing clamps. If necessary, cut a section of 1/8" yellow line out of the umbilical to make connection.. (See connection K.) 17. Route the main harness through the 5' x 1-3/4" corrugated ducting hose to the inside of the chair pump cover. (For future connections if necessary.) 18. In the USC, open the air/water stop valves and check for leaks. Reprogramming Chair Special instructions for the DentalEZ E-3000 Chair: To prevent the Magellan unit post from damaging the USC cover or chair pump cover when the chair is in its lowest position, it is necessary to reprogram the travel limits according to the programming travel limits instructions provided for the appropriate chair. Main Harness J Adaptor Harness Power Pack Transformer 26 Installation, Operation and Care Manual

28 Section IV Testing IMPORTANT NOTE Before testing the delivery system, make sure the shipping tie wrap is removed from the adjustable arm pivot area at the delivery head. Utility Service Center 1. Turn ON all services supplying the USC. 2. Open the air and water manual stop valves by turning knobs counterclockwise 3. Inspect all joints and connections for leaks. 4. Plug the power cord from the USC into an electrical outlet. 5. Turn the unit's master switch ON. Handpieces CAUTION Before connecting handpieces, all air must be purged from the coolant water lines to allow the system to function properly. Coolant Water Lines 1. At the foot control, flip the toggle valve to WET. WET/DRY Toggle Valve Wet Master ON/OFF Switch 6. Inspect for leaks in delivery head and the USC. Air/Water Regulators The water regulator is factory preset to deliver 40 PSI. The air regulator is factory preset to deliver 80 PSI. NOTE: If the water or air regulator needs calibration, perform the following three steps. 1. Lift up the adjustment knob on the regulator. 2. Turn the adjustment knob until the correct pressure reading is attained. 3. Push the adjustment knob down when finished. 2. Perform the following steps (a. through f. on the next page) to purge air from the coolant water lines for each handpiece. a. Turn the coolant water valves counterclockwise to their full, open position. (Traditional Delivery Head Shown) Water Coolant Valves b. Remove the handpiece tubing from each holder. axcs Magellan CMU 27

29 Section IV Testing axcs Magellan CMU ISO 4-Line Connector Tubing Coupler Tubing c. While facing the delivery head, start with the handpiece tubing on the far left; then fully depress the foot control and allow the water to flow into a sink or other container. d. As the water is flowing, continue the purging operation of the remaining tubings (moving from the left tubing to the right). e. Allow water to flow freely from all of the tubings for approximately two minutes to ensure all air has escaped. 3. Perform the following steps (a. through c.) to attach each handpiece tubing: a. Slide the tubing coupler down along the tubing to expose the ISO 4-line connector. b. Carefully align and insert the handpiece base into the ISO 4-line connector. c. Replace and tighten the tubing coupler to complete installation. Drive Air Pressure Handpiece (Insert Air Pressure Gauge Here) CAUTION To function properly, individual handpiece drive air pressure must set according to the manufacturer's specification. 1. At the foot control, flip the toggle valve to DRY. 2. To adjust the individual handpiece drive air pressure to the manufacturer's specification, perform the following steps (a. through e.): a. Remove the handpiece from its holder. b. Insert an air pressure gauge as indicated in the illustration on this page. c. While holding the handpiece, fully depress the foot control and observe the amount of air pressure delivered to the handpiece. d. Locate the air pressure adjustment screws on the bottom of the delivery head chassis. (Traditional Delivery Head Shown) Air Pressure Adjustment Screws e. Using a slotted screwdriver, turn the air pressure adjustment screw on the control valve of the appropriate handpiece (counterclockwise to increase pressure, clockwise to decrease pressure) until the handpiece manufacturer's correct specification registers on the pressure gauge. 3. Repeat the previous steps (a. through e.) to set the pressure for each handpiece. Flush Valve To test the flush valve: 1. Remove the handpiece from its holder. 2. Activate the flush toggle valve. 3. Operate each handpiece for 30 seconds into a sink or open vacuum line. 28 Installation, Operation and Care Manual

30 Section IV Testing Optional Features Syringe (Euro Style) If the unit is equipped with a syringe, first depress the air and then the water button to test the flow. NOTE: If syringe adjustments are necessary, perform the following three steps: 1. Unscrew the syringe handle. 2. Turn the adjustment screws using the tool provided 3. Turn the screw counterclockwise to increase the flow, clockwise to decrease the flow. Fiber Optics Follow the test procedures outlined in the instructions included in each fiber optic handpiece package. Chipblower If the unit is equipped with a chipblower, a burst of air should be delivered to the handpiece when the chip air valve on the foot control is depressed. NOTICE After final testing is complete, install all covers and upholstery. EURO-STYLE Adjustment Screw Assistant's Vacuum Accessories 1. Make sure the shut off valve located on the underside of the rear assistant's head is in the OPEN position. 2. Evacuate one cup of water (8 oz. each) through the saliva ejector and the highvolume evacuator. axcs Magellan CMU 29

31 Section V Operation axcs Magellan CMU Delivery Head The axcs Magellan unit offers the following design features: Operation of three handpieces and a syringe. Drive air and coolant water may be adjusted individually for each handpiece. Foot control toggle valve allows wet or dry cutting. Master switch turns entire unit ON and OFF. Easy cleaning and disinfecting. Master Switch Controls Traditional & Euro-Style Head The master toggle switch located in the rear of the delivery unit controls the ON/OFF function of air, water and electricity to the entire unit. Flip the toggle switch to the right to turn ON the unit. IMPORTANT: At the end of each work day, and anytime the unit is unattended, make sure the master control switch is in the OFF position. An automatic CUT OFF, which can be demonstrated by placing tubing in the hanger and disabling operation for that position. Rotate Handpiece Holder Set Screw Instrument Hanger The handpiece holder angle can be adjusted by using an Allen wrench to loosen two set screws and rotating the holder to the desired angle; then retightening the screws. An oil collector/filter is designed to collect oil from the handpiece exhaust air. Periodically check the filter for cleaning or replacement by lifting the delivery head cover and removing the screws that secure the filter cover. Master ON/OFF Switch Swing-Away Instrument Hanger Traditional Head This feature s design allows the following functions: The entire instrument hanger bar can be moved to the left or right to provide easy access to the optional tray on top of the delivery head. Grasp the delivery head with one hand; with the other hand, grasp the instrument hanger bar handle and move it to the left or right Euro-Style Head Oil Collector/ Filter This feature s design allows the following functions: The multi-positional tray pivots around from left to right. The multi-positional tray can also move back and forth for easy tubing access. 30 Installation, Operation and Care Manual

32 Section V Operation Euro-Style Delivery Head Handpieces Coolant Water Spray Coolant water spray to all the handpieces can be turned ON or OFF using the toggle switch located on the foot control. The coolant spray volume is manually adjustable for each handpiece by using fingers. 1. While operating the handpiece, turn the water coolant valve counterclockwise to increase the volume of coolant water spray. Handpieces and syringe instruments conveniently lay in four recessed areas on top of the delivery head cover. Delivery Head Positioning The horizontal and vertical location of delivery head can be varied by doing the following: To vary the horizontal location, push or pull the instrument hanger bar handle. To raise the delivery head, lift up the instrument hangar bar handle. Brake Release Button To lower the delivery head, depress the brake release button, lift slightly on the handle and push the head down using the handle. Release the button when the delivery head is in the desired position. (Traditional Delivery Head Shown) 2. To decrease the volume, turn the water coolant valve clockwise. Air Pressure Water Coolant Valves Air Pressure Adjustment Screws Air pressure to each handpiece can be adjusted to the manufacturer's specifications by following the instructions in Section IV Testing under the heading Drive Air Pressure on Page 28. NOTE: These procedures must be done while: The master switch is in the ON position, The handpiece is out of its holder and The foot control is fully depressed. NOTE: When making necessary air pressure adjustments, refer to the air pressure gauge located at the front of the delivery head to check the approximate amount of air pressure delivered to the handpiece. axcs Magellan CMU 31

33 Section V Operation Flush System It is recommended that the tubing of each handpiece used be flushed after each patient. 1. Hold the handpiece tubing over a sink, cuspidor or open vacuum line. axcs Magellan CMU 2. Slide the ferrule down the tubing to expose the metering block. 3. Using the screw adjustment tool (provided in the accessories package), adjust air, water and spray by turning the appropriate screw counterclockwise to increase volume, or clockwise to decrease volume. Euro-Style Flush Toggle 2. While facing the front of unit, move the FLUSH toggle located at the rear of the delivery head to the left, and hold it there for 20 seconds. NOTE: Flushing the water line in the handpiece can be done by operating the FLUSH valve while either fully depressing or not depressing the foot control. Syringe The syringe is designed to deliver air or water, or a mixture of air and water, as required. To deliver water only, press the button on the syringe marked with a water drop symbol. For air only, press the button on the syringe with no marking. To get a spray mixture of air and water, press both buttons simultaneously. NOTE: Air and water flows are factory preset. For Euro-Style Only If an air or water flow adjustment is wanted, use the following procedure: 1. Grasp the syringe valve body assembly and unscrew the ferrule by turning counterclockwise. Ferrule WET/DRY Toggle Valve Disc Adjustment Screws Foot Control Valve Body 4. Grasp the syringe valve body assembly and slide the ferrule over the metering block. 5. Hand tighten to the valve body. The speed of the handpiece is controlled by depressing the disc located on the foot control. A light pressure on the foot control disc causes a slow speed. Full pressure on the disc causes the handpiece to operate at full speed. NOTE: The coolant water spray ON/OFF function is also controlled by using the toggle valve located on the foot control as described above. Optional Chipblower 32 Installation, Operation and Care Manual

34 Section V Operation Clean Water System (Optional) Operation of the optional clean water system is as follows: Flip the toggle switch (A) to the ON position Assistant's Vacuum Accessories The assistant's arm pivots allowing easy access of instruments Standard instrumentation is one HVE and one saliva ejector Optional features include an additional HVE and/or a three-way syringe Use the pressure adjusting valve (B) to set the air pressure at 40 PSI on the gauge (C) IMPORTANT NOTE: Do not exceed 40 PSI Flip the toggle switch (D) to change usage from bottle water to city water Clean Water Option A D Saliva Ejector Highvolume Evacuator To remove the bottle (E), first flip the toggle switch (A) to the OFF position, then unscrew it from the assembly NOTE: Order kit # if desired C B E Syringe HVE and Saliva Ejector The flow of vacuum through the HVE and saliva ejector is controlled by a lever valve Pushing the lever forward, toward the tip, closes the vacuum Chipblower (Optional) HVE Saliva Ejector This feature is used to blow debris away from the cutting site by creating an air blast through the handpiece without causing the bur to rotate To operate the chipblower, depress and hold down the valve on the upper right of the foot control Lever Valve Open Closed Lever Valve Open Closed Fiber Optics (Optional) The fiber optics control is automatically activated by operating the handpiece using the foot control NOTE: When the foot control is released, the fiber optics light will stay on for approximately ten seconds to allow inspection of the cutting site As the lever is moved toward the hose end of the valve, the vacuum flow increases To close the valve, move the lever all the way toward the tip of the valve Syringe NOTE: See the syringe operating instructions on Page 32 axcs Magellan CMU 33

35 Section VI Care Cleaning The axcs Magellan unit should be cleaned as follows: Wipe frequently with a damp, lint-free cloth. Use a mild detergent to clean stains. CAUTION Do not use abrasive cleaning agents. At the end of the day, turn the master ON/ OFF valve to the OFF position and clean the instrumentation. Each morning, turn the master valve ON and check the air and water system for proper operation using the three-way syringe. NOTE: It is recommended that puncture-resistant nitrile gloves be worn for the following procedures: High-Volume Evacuator (HVE) With the high-volume evacuator vacuum valve in the OFF position, disconnect the valve. Using a brush, clean the interior of the valve under a faucet, and rinse thoroughly. Saliva Ejector Disconnect the saliva ejector valve from the tubing and repeat the procedure described for the HVE. Solids Collector To clean the solids collector, located at the instrument end of the assistant's arm, do the following: 1. Close the vacuum ON/OFF valve. 2. Push the lever on the saliva ejector downward to equalize pressure. 3. Remove the lid by lifting it straight up. 4. Grasp the stem on the basket and lift the basket straight up. 5. Empty debris and wash out the basket with axcs Magellan CMU warm water, then replace the basket and lid. 6. Open the vacuum ON/OFF valve. Clean Water System Empty the bottle at the end of each day. Then before the day's first procedure, fill it with fresh clean water. NOTICE Cleaning brushes and Vac-U-Ez solution can be ordered through DentalEZ dealers. Disinfecting NOTE: After cleaning the high-volume evacuator, saliva ejector and solids collector, evacuate two cups of Vac-U-Ez cleaning solution (one cup each) through the high-volume evacuator and saliva ejector to sanitize the system. CAUTION Avoid using disinfectants in spray containers because they may cause premature staining, discoloration and/or damage to the unit. Liquid disinfectants are recommended for use on all axcs Magellan external surfaces and should be applied using a soft, clean cloth. CAUTION Do not use disinfectants that contain any of the following: Iodophors Glutaraldehydes Phenols Sodium Hypochlorites Use extreme caution when selecting the proper chemical disinfectant for the axcs Magellan CMU. NOTE: *Cavicide is the recommended disinfectant for use on all external surfaces. *Cavicide is a trademark of Micro Aseptic Products, Inc. CAUTION Be sure not to exceed a temperature of 275º F. 34 Installation, Operation and Care Manual

36 Section VII User Service Information A fold-out, full-color axcs Magellan delivery system tubing diagram is located at the end of this manual. The following charts should be used when troubleshooting operational problems. If these suggested troubleshooting procedures do not resolve the problem, see the Service Instruction on Page 39. WARNING Exercise extreme caution when troubleshooting the electrical components of the axcs Magellan CMU. When testing, always disconnect the external power. When electrical power is required, safety precautions must be followed. S ymptom Possible Cause(s) Delivery Head Solution Unit will not turn on. No air to master switch. Faulty master switch. Faulty air pilot valve. Open stop valve in floor utility box. Open and adjust air regulator to 80 PSI. Check for pinched red 1/8" tubing in arms. Turn switch on and verify air flow. Verify an air supply to top fitting of valve. Unit has no electric power. Tripped circuit breaker. No building power. If air is present at top fitting of valve, verify air to foot control tubing. If no air at tubing, valve is defective. Reset circuit breaker on power module in USC. Check main circuit supply. Faulty eletric switch. Contact electrician. Verify air signal at air/electric switch of power module. Power module or power box not plugged in. Inproper outlet voltage. Plug in power moduleor power box Verify proper outlet voltage in USC. inside USC. Unit air. has no Unit is not turned on. Air stop valve is closed. Pinched air line. Faulty air pilot valve. Ensure master toggle valve is in O N position. Turn stop valve on and verify 80 PSI on air gauge. Check for pinched or restricted 1/4" red tubing from floor utility box to post-mounted console. Check barbs for blockage. If none, replace valve. No water (hand-piece & syringe) Water toggle is in O FF position. No water in clean water bottle. Place Fill bottle. the clean water system toggle in O N position. Pressure regulator not adjusted. No air to bottle water system. Slide clamp is clamping line. Ensure clean water system gauge reads 40 PSI. Check for pinched or restricted airline. Move clamp to allow water flow through line. axcs Magellan CMU 35

37 Section VII User Service Information axcs Magellan CMU S ymptom Possible Cause(s) Delivery Head (continued) Solution Air in coolant water. Water flush f ails to operate. Unit has not been purged. Faulty water control valve. Water toggle is in O FF position. No water in clean water bottle. Faulty water flush toggle valve. Purge water lines. If unit was purged, replace water control valve. Place toggle in O N position. Fill clean water bottle. If water is present at valve, but not flowing, replace valve. S ymptom Possible Cause(s) Handpiece Solution No drive air. No fiber optic light at handpiece. Drive air flow adjustments pinch valves are closed. on Faulty handpiece holder valve. Faulty foot control. Pinched or restricted tubing. Power transformer is not plugged in. Internal wires in control head and post-mounted console are not connected. No signal air to fiber optic lamp control. Faulty transformer. Faulty fiber optic control. Faulty bulb. No signal air to receptacles in the USC. Using a screw driver, turn adjustment screw counterclockwise to adjust drive air pressure. Set to manufacturer's recommended pressure. If pinch valve does not release with handpiece out of holder and tubing to holder is not restricted, replace hanger valve. Depress foot control. If no air is present, repair or replace foot control. Straighten or replace tubing. P lug transformer into designated receptacle in USC. Check connections in control head and post-mounted console. Check for pinched or restricted tubing. Check output for VAC. Fiber optic controls have a calibration range of 2.5 to 6.0 VDC. Check for proper voltage according to the handpiece manufacturer's recommendations. Replace bulb. Check for pinched or restricted tubing. 36 Installation, Operation and Care Manual

38 Section VII User Service Information Handpiece (continued) S ymptom Possible Cause(s) Solution No coolant water at any handpiece Water dribbles from handpiece while in holder. Water dribbles from handpiece after foot control is released. No coolant air to handpiece. Coolant water adjustment valves closed. Water toggle on foot control is in the O FF position. Water toggle on clean water system is in O FF position. Slide clamp is in clamped position. Water bottle empty. Pressure too low on clean water system. Pinched or restricted tubing. Faulty handpiece holder. Pinched or restricted tubing to holder. Pinch valve leaking. Low air pressure. Low air pressure. diaphragm is Faulty water control valve. Faulty water relay in foot control. Pinched or restricted tubing from foot control. Slide clamp is in clamped position. Pinched or restricted tubing. Turn valve counterclockwise to open valve. Flip Flip toggle to the right for the toggle to the O N position. O N position. Slide clamp so it moves freely on tubing. Fill water bottle. Verify clean water system pressure adjust accordingly. Straighten or replace tubing. Repair or replace holder. Straighten or replace tubing. Replace diaphragm. gauge reads 40 PSI and Ensure air regulator gauge in floor box reads 80 PSI. Ensure air regulator gauge in floor box reads 80 PSI. Depress foot control then release. Remove black tubing from water control valve. If dribble continues, replace valve. Turn unit off. Open foot control and inspect water relay block. If piston is not damaged and is moving freely, stretch the spring. Reassemble and retry foot control. Straighten or replace tubing. Reposition slide clamp so it moves freely on tubing. Straighten or replace tubing. axcs Magellan CMU 37

39 Section VII User Service Information axcs Magellan CMU Arm System S ymptom Possible Cause(s) Solution Horizontal arms drift left or right. Unit head is not level from front to back. Adjustable arm does not hold position. Adjustable arm will not move. Unit Pivot is not properly leveled. is not properly adjusted. Improper adjustment. Faulty brake switch. Faulty lock arm actuator. Faulty brake switch. No air to brake switch. Faulty arm lock actuator. Verify unit seated. is level. Also, verify arms are properly Remove adjustable arm cover and adjust nut at pivot. With nothing on delivery head, adjust the nut on the spring so unit stays in place. Remove adjustable arm cover to see if locking arms are in place. If they are stuck in the up position, check brake switch. When brake switch is activated, ensure lock arm actuator strikes lock arms. Also, ensure lock arm actuator is not stuck in actuate position. When brake switch is depressed, ensure air is reaching lock arm actuator. Ensure unit master toggle is in O n postion. If air is reaching actuator, but not extending, replace lock arm actuator. S ymptom Possible Cause(s) Water Heater Solution No warm water, cold water only. Extension cord heater. disconnected from water Water temperature is set too low. Pinched or restricted signal air tubing (1/8" yellow) to electrical receptacle in post-mounted console. Unit's extension cord is not connected to power supply. Faulty water heater. Ensure extension cord in post-mounted console is plugged into water heater. Turn adjustment screw on water heater clockwise to increase temperature. Straighten or replace tubing. Verify power supply and proper extension cord connection inside USC. Replace water heater. 38 Installation, Operation and Care Manual

40 Section VII User Service Information Service Instruction If the problem is not addressed or cannot be isolated by performing the suggested troubleshooting procedures, contact your local DentalEZ full-service dealership. (See Product Support Services, Page 49.) Please have the following product information available: Model Name Model Number Serial Number (Model and serial numbers found on the underside of the delivery head chassis.) Date of Installation Dealer Model Number Serial Number Delivery Head Chassis axcs Magellan CMU 39