Procenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation

Transcription

1 Procenter Delivery Mounted on a Free Standing Treatment Console (FTC) Installation Electrical Requirements: 24 VAC, 3.2 Amp 13VAC, 2 Amp Attention These instructions apply to Midmark cabinetry. For other cabinetry, additional steps may be required. Refer to 12:00 Procenter Delivery Mounting Kit Installation Instructions [ ] to confirm necessary steps have been completed before proceeding with this installation. Components: none Special Tools: none Cabinet Mount Arm (Pivoting) Cabinet Mount Arm (Pull Out) Leave push retainers on screws for install. Align mounting holes in leveling plate and cabinet mount arm plate with mounting holes in cabinet. Secure with screws but do not tighten. Locate three holes toward front of cabinet for proper rotation when installing. DA2230i Rev. S (11/3/16)

2 Mounting Control Panel Align top and bottom slides on delivery panel with slides on cabinet and carefully move into position. Step 3: Route foot control tubing through hole in cabinet base. Secure with screws. Position bearing race at end of each slide that is attached to cabinet. DA2372i : Slides maybe mounted on RH side of cabinet. 2

3 Regulator Installation Insert regulator into compression fitting of shut-off valve and tighten compression fitting. : Delivery and Assistant s Unit Tubing Connections are located in cabinet base. WATER REGULATOR Regulator Compression Fitting Shutoff Valve AIR REGULATOR Compression Fitting Regulator Shutoff Valve Tubing Connections (J-Box) Foot Control (Procenter Delivery Unit Only) The diagram shows all possible connections for the delivery system. Foot Control used for Delivery Unit (Only) Vacuum Connections used for Assistant s Unit (Only). 80 PSI 1/4 Grey (Ribbed) Rib 1/4 Grey (Plain) Master Pilot Shut-Off Transformer Air Pressure (Optional) Grey (Above 1/4 Ribbed) Grey Input INACTIVE - no air from master switch Air Supply ( PSI) Master Pilot Shut-Off 1/4 Clear Orange Green or 1/4 (Filtered / Regulated Air - [80 PSI]) (Filtered / Regulated Air - [80 PSI]) Purple (Unfiltered / Unregulated Air - [ PSI]) To Handpiece Coolant Air To Pilot Air for Coolant To Handpiece Drive Air Air To Master ON/OFF Switch Air To Syringe Air To Bottle Unfiltered Output ( PSI]) Air From Master ON/OFF Switch ACTIVE - air coming from master switch Filtered Output Supply (30-50 PSI) Master Pilot Shut-Off 30 PSI 5/8 Vacuum Vacuum Supply Tube (Assistant s Unit Only) Syringe Tubing Ribbed Side Instrument from Control Panel / Bottle Assembly City to/ Selector Valve 3

4 Work Surface / Unit Mount Arm Installation & Adjustment Cabinet Mount (Pivoting) Cabinet Mount (Pull Out) Maximum Weight Limitation 40 lbs. (18 kg) Align desired mounting holes in work surface, leveling plate, and mount arm. Secure with screws. Work Surface Work Surface Plate On the Pivoting Unit, Insert Unit Mount Arm into Cabinet Mount Arm. Mount Arm Cabinet Mount Arm Plate Mounting Step 4: Pivot Points & Set On the Pivoting Unit, Adjust drag by loosening or tightening set screws at pivot points. Step 3: DA2233-1i Work Surface: Loosen mounting screws. Adjust leveling screws. Retighten mounting screws. Mounting 4

5 Routing / Securing Tubing Cabinet Mount (Pivoting) Adhesive backed mounting platforms are provided for units without control panel. Apply mounting platform to inside of cabinet and secure vacuum with wire tie: then go to step 2. Cabinet Mount (Pull Out) For ease of installation it may be helpful to extend the work surface by pulling it outward. Equipment Alert When securing tubing, allow sufficient slack in tubing for movement of control panel / mounting arm. Failure to do so could result in tubing becoming disconnected or damage. Bundle tubing from Doctor s / Assistant s Delivery Units and install in brackets then secure with screws. Bundle tubing from control panel and install bracket; DA2394i then secure bracket with screws. Loosen screws on both side of mounting brackets and remove bracket.. 5

6 Tray / Tub Assembly Installation for Pull Out Unit The Work Surface assembly can accommodate accessories (9 x 13 Tray Assembly or a Tub Support). The assembly can be installed for either right or left hand operation. Step 4: Install the Tray Assembly or Tub Support. Position tray clamp assembly onto work surface and tighten thumb screw. Step 3: Insert the flange bearing into tray clamp assembly. Base used with Corian tops If necessary, replace base of tray clamp assembly by removing screws, thumb screw, and clamp plate, place new base in place and re-assemble. : Used on Laminate and Quartz work surfaces. Base used with Laminate and Quartz tops. DA2395i 6

7 Chair Control Touch Pad Connections (Optional) LH Mount (Shown) Open Equipment Base mounts to Center Console with 3 screws. On Side Delivery Units, the shipping leg must be removed first. The following procedure applies only when using this delivery system with a Midmark Dental Chair. If not using a Midmark Dental Chair, or if the delivery system does not include the optional Chair Position Touch Pad, this procedure is not necessary. Connect 15 ft. wire harness to touch pad wire harness. Route wire harness out through hole in front of base and install bushing. 15 ft. Extension Step 4: Connect 12 in. wire harness extension to J2 position on Chair PC Board. 12 in. Extension Step 5: Connect 12 in. wire extension to wiring harness. Hydraulic Cover Step 3: Remove Hydraulic Cover and route wire harness behind base cover of chair. J2 J10 Chair PC Board J11 J13 Step 6: Install Hydraulic Cover. DA2371i 7

8 Tubing Connections (Vacuum Instrument Arm Assembly) Saliva Ejector Closed Open Open Closed Air N.C. Limit Switch COM NC High Volume Evacuator (HVE) 30 PSI Quick Disconnect Master On/Off Valve 1/4" " Double Pinch Valve " Air 80 PSI Air Quick Disconnect N.C. Limit Switch NC Assistant's Unit w/ Optional Switches COM F E D C B A 24 V 24 V 0 V 0 V Orange Green White Black To Junction Box Solids Collector Capped Vacuum To Umbilical Vacuum Supply Bottle Cap City Syringe Tubing Orange Umbilical Bottle In line Regulator Orange N.C. Limit Switch NC COM Selector Valve City Push (Optional) FlushValve (N.C.) 2-Way Manual Momentary 8