Axle Bearing: Service and Repair Rear Axle Hub, Bearing, Cup, and/or Seal Replacement
|
|
- Holly Newman
- 5 years ago
- Views:
Transcription
1 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page 1 Axle Bearing: Service and Repair Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Special Tools * CH Axle Hub Nut Socket * DT Differential Bearing and Hub Seal Installer * DT Wheel Bearing Installer Outer Bearing Cup * DT Wheel Bearing Race Installer-Outer * DT Wheel Bearing Race Installer- Inner * J Universal Driver Handle-3/4 x 10 inch For equivalent regional tools, refer to Special Tools (See: Differential Assembly/Tools and Equipment/Rear Drive Axle). Removal Procedure Note: * The wheel speed sensor ring is NOT serviced separately. The hub and wheel speed senor ring are serviced as an assembly. * The wheel hub seal must be replaced anytime the wheel hub assembly is removed from the axle housing. 1. Raise the vehicle. Refer to Lifting and Jacking the Vehicle (See: Maintenance/Vehicle Lifting/Service and Repair). 2. Remove the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair). Note: In the following service procedure, it is not necessary to remove the brake caliper from the bracket. 3. Remove the brake caliper bracket. Refer to Rear Brake Caliper Bracket Replacement (JD9) (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and Replacement/Rear Brake Caliper Bracket Replacement (JD9))Rear Brake Caliper Bracket Replacement (J90, J95, J96) (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and Replacement/Rear Brake Caliper Bracket Replacement (J90, J95, J96)). 4. Remove the axle shaft. Refer to Rear Axle Shaft and/or Gasket Replacement (See: Seals and Gaskets/Service and Repair/Rear Axle Shaft and/or Gasket Replacement). 5. Remove the key.
2 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page 2 6. Remove the adjuster nut retainer (1). 7. Using the CH socket (1), loosen the adjusting nut.
3 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page 3 8. Remove the adjusting nut. Note: If the oil seal remains on the axle hub, remove the seal using a suitable seal removal tool. 9. Remove the wheel hub/brake rotor assembly (1) from the axle housing. 10. Remove the rotor, if necessary. Refer to Rear Brake Rotor Replacement (JD9) (See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (JD9))Rear Brake Rotor Replacement (J90, J96) (See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (J90, J96))Rear Brake Rotor Replacement (J95) (See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (J95)). 11. Using a suitable seal removal tool, remove the oil seal from the wheel hub. 12. Remove the inner hub bearing. 13. Using a brass drift and a hammer, remove the inner hub bearing cup.
4 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page Remove the retaining ring from the wheel hub. 15. Using the DT installer (2) and the J handle (1), remove the outer hub bearing and bearing cup. nstallation Procedure 1. Lubricate the following with a light coat of high melting point EP bearing lubricant: * The outer wheel bearing * The inner wheel bearing * The outer wheel bearing cup * The inner wheel bearing cup * The axle hub spindle 2. Install the outer bearing into the wheel hub.
5 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page 5 Note: Drive the outer bearing cup into the wheel hub until it is just past the retaining ring groove. Do not bottom out the bearing assembly in the bore. 3. Using the DT installer (2) and the J handle (1), install the outer bearing cup into the wheel hub. Note: Ensure that the retaining ring is fully and evenly seated in the groove. 4. Install the retaining ring into the groove. Note: Ensure that the outer bearing assembly rotates freely in the hub 5. Using the DT installer (2) and the J handle (1), turn the wheel hub over and seat the outer bearing assembly against the retaining ring. 6. Turn the wheel hub over and install the inner bearing cup.
6 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page 6 7. Using the DT installer (2) and the J handle (1), install the inner bearing cup into the wheel hub. 8. Install the inner bearing. Note: Ensure the seal is fully seated in the hub bore. 9. Using the DT installer (2) and the J handle (1), install the new oil seal. 10. Install the rotor, if necessary. Refer to Rear Brake Rotor Replacement (JD9) (See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (JD9))Rear Brake Rotor Replacement (J90, J96) (See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (J90, J96))Rear Brake Rotor Replacement (J95) (See: Brakes and Traction Control/Disc Brake System/Brake Rotor/Disc/Service and Repair/Removal and Replacement/Rear Brake Rotor Replacement (J95)). 11. Apply a light coat of high melting point EP bearing lubricant to the axle housing spindle.
7 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page 7 Note: If the wheel hub assembly does not fully seat itself onto the axle shaft spindle and is removed, the wheel hub seal must be replaced. 12. Install the wheel hub to the axle housing. 13. Install the rear axle adjuster nut (1).
8 2011 Chevy Truck Silverado WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA Page Using the CH wrench (1), install the adjusting nut to the hub. 15. Adjust the wheel bearings. Refer to Wheel Bearing Adjustment (See: Differential Assembly/Service and Repair/Procedures/Rear Drive Axle/Wheel Bearing Adjustment). 16. Install the adjuster nut retainer (1). 17. Install the axle shaft. Refer to Rear Axle Shaft and/or Gasket Replacement (See: Seals and Gaskets/Service and Repair/Rear Axle Shaft and/or Gasket Replacement). 18. Install the brake caliper bracket. Refer to Rear Brake Caliper Bracket Replacement (JD9) (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and Replacement/Rear Brake Caliper Bracket Replacement (JD9))Rear Brake Caliper Bracket Replacement (J90, J95, J96) (See: Brakes and Traction Control/Disc Brake System/Brake Caliper/Service and Repair/Removal and Replacement/Rear Brake Caliper Bracket Replacement (J90, J95, J96)). 19. Install the tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair). 20. Inspect and add axle lubricant to the axle housing, if necessary. Refer to Rear Axle Lubricant Level Inspection (8.6, 9.5 LD Axle) (See: Differential Assembly/Fluid - Differential/Service and Repair/Procedures/Rear Drive Axle/Rear Axle Lubricant Level Inspection (8.6, 9.5 LD Axle))Rear Axle Lubricant Level Inspection (10.5 Inch Axle) (See: Differential Assembly/Fluid - Differential/Service and Repair/Procedures/Rear Drive Axle/Rear Axle Lubricant Level Inspection (10.5 Inch Axle))Rear Axle Lubricant Level Inspection (11.5 Inch Axle) (See: Differential Assembly/Fluid - Differential/Service and Repair/Procedures/Rear Drive Axle/Rear Axle Lubricant Level Inspection (11.5 Inch Axle)). 21. Lower the vehicle.
Rear Axle Hub, Bearing, Cup, and/or Seal Replacement
Page 1 of 11 Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Special Tools J 8092 Universal Driver Handle - 3/4 inch - 10 J 2222-C Wheel Bearing Nut Wrench J 24426 Wheel Bearing Race Installer - Outer
More information1988 Jeep Truck Wrangler L L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # Date:
1988 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 025288 Date: 880711 Right Front Axle Shaft Seal - Installation Models 1986-88 Jeep Comanche,
More information1988 Chevrolet Pickup V SUSPENSION - FRONT (4WD)' 'Front Suspension - "V" Series 1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series
1988 SUSPENSION - FRONT (4WD) Front Suspension - "V" Series DESCRIPTION NOTE: Vehicle serial numbers used in this article has been abbreviated for common reference to Chevrolet and GMC models. Chevrolet
More informationWRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT
WRANGLER, CHEROKEE AND COMANCHE, FRONT AXLE WHEEL HUB CONVERSION KIT -YA WU-07 5 x 4.5 -YA WU-08 5 x 5.5 *THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS AND YA WU-08 WILL CHANGE BOLT PATTERN TO 5 ON 5.5*
More informationFig. 1: Exploded view of the 2WD hub and bearings
Page 1 of 8 Front Wheel Bearings REPLACEMENT NOTE: Sodium-based grease is not compatible with lithium-based grease. Read the package labels and be careful not to mix the two types. If there is any doubt
More informationFront Hub and Disc (4WD Model)
4C 8 DRIVE SHAFT SYSTEM Disassembled View Front Hub and Disc (4WD Model) 411RW001 Legend (1) Bolt (2) Cap (3) Snap Ring and Shim (4) Hub Flange (5) Lock Washer and Lock Screw (6) Hub Nut (7) Outer Bearing
More informationInstallation Notes: #86000-R Race Series +3.5 L/T Kit
159 North Maple St. Unit J, CORONA CA 92880 P. 951-737-9682 F. 951-737-9006 WWW.CHAOSFAB.COM Installation Notes: #86000-R Race Series +3.5 L/T Kit Factory manual is recommended for removal and re-installation
More informationTB Technical Bulletin. Harlan Drive Axle Series 1 Inner Wheel Bearing Inspection. Product Improvement News. Feb. 19, 08 Page 1 of 31 Pages
Page 1 of 31 Pages Harlan Drive Axle Series 1 Inner Wheel Bearing Inspection February 19, 2008 Page 2 of 31 Pages Phone Numbers Harlan Global Manufacturing 27 Stanley Road Kansas City, KS 66115 USA...800
More informationAutomatic Transmission/Transaxle: Removal and Replacement Transmission Replacement
2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA 10.52 Page 1 Automatic Transmission/Transaxle: Removal and Replacement Transmission Replacement Transmission Replacement Tools Required * J 41623-B Cooler
More informationIN-VEHICLE REPAIR. Differential Bearings. Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear. Special Tool(s)
205-02A-1 IN-VEHICLE REPAIR Differential Bearings Special Tool(s) Protector, Drive Pinion Thread 205-460 Special Tool(s) Installer, Differential Shim 205-220 (T85L-4067-AH) 205-02A-1 2-Jaw Puller 205-D072
More information1984 Dodge W250 PICKUP
1984 Dodge W250 PICKUP Submodel: Engine Type: V8 Liters: 5.2 Fuel Delivery: CARB Fuel: GAS Dana 44 MODELS THROUGH 1984 2. Raise and safely support the vehicle, then remove the wheel hub and bearings as
More informationSUSPENSION - FRONT Infiniti G20 DESCRIPTION ADJUSTMENTS & INSPECTION SUSPENSION Front G20
SUSPENSION - FRONT 1992 Infiniti G20 1991-92 SUSPENSION Front G20 DESCRIPTION G20 uses a 4-wheel independent multi-link suspension system. Transverse links are connected to bottom of steering knuckle.
More information2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
More information2. Rear Axle 4-2 [W2A1] SERVICE PROCEDURE A: REMOVAL 1. DISC BRAKE. Tightening torque: 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.
4-2 [W2A1] SERVICE PROCEDURE 9) Install tie-rod end ball joint on housing knuckle arm. 27.0±2.5 N m (2.75±0.25 kg-m, 19.9±1.8 (1) Cotter pin (2) Castle nut (3) Tie-rod B4M2214B 10) While depressing brake
More information*THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS*
*THIS KIT IS NOT INTENDED FOR VEHICLES WITH ABS* Notes: New full-cast rotors from 1990 or newer Wrangler must be used with this kit, this rotor (ITT #65225 or equivalent) has a.25 thick mounting flange.
More informationJK 8 Lug Front Locking Hub Conversion Kit
JK 8 Lug Front Locking Hub Conversion Kit Kit #3034411 w/ Performance Rotors Kit #3034410 w/ Performance Slotted Rotors Kit #3034412 w/ Big Brake Kit Kit #3034413 w/ Big Brake Kit and Slotted Rotors Important
More informationSUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm. Acrobat Printable Version
SUSP-09, Rear Wheel Bearing Replacement - Steel Trailing Arm Introduction Acrobat Printable Version I'd like to thank Ben Davis for providing the pictures for this procedure. Ben took the time to take
More informationTiming Chain: Service and Repair
1996 Nissan-Datsun Truck D21 Hardbody 2WD L4-2389cc 2.4L SOHC MFI (KA24E) Copyright 2013, ALLDATA 10.52 Page 1 Timing Chain: Service and Repair *** THIS ARTICLE INCLUDES UPDATES MADE BY TSB 95027, DATED
More informationDIFFERENTIALS & AXLE SHAFTS
DIFFERENTIALS & AXLE SHAFTS 2001 Chevrolet Camaro 2000-01 DRIVE AXLES General Motors Differentials & Axle Shafts Chevrolet; Camaro Pontiac; Firebird DESCRIPTION & OPERATION Drive axle is a semi-floating,
More information4. Rear Axle REAR AXLE
REAR AXLE DRIVE SHAFT SYSTEM 4. Rear Axle A: REMOVAL 1) Disconnect the ground cable from battery. 2) Lift-up the vehicle, and remove the rear wheel. 3) Unlock the axle nut. 4) Remove the axle nut using
More informationOn-Vehicle Service Hub and Drum Assembly. Remove or Disconnect (Figures 1, 3-5) 1 of 8 11/25/2016 2:47 PM
1 of 8 11/25/2016 2:47 PM On-Vehicle Service Hub and Drum Assembly Remove or Disconnect (Figures 1, 3-5) Tools Required: J-35012 Rear Hub Bearing Nut Wrench J-35013 Rear Hub Remover 1. Remove the drain
More informationREAR DRIVE SHAFT (3S GTE ENGINE)
SA52 REAR DRIVE SHAFT (3SGTE ENGINE) COMPONENTS SA53 NOTICE: The axle bearing could be damaged if it is subjected to the vehicle weight, such as when moving the vehicle with the drive shaft removed. Therefore,
More informationSUSPENSION - REAR Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - REAR 1988 Toyota Celica REAR SUSPENSION Toyota IRS DESCRIPTION The Toyota Independent Rear Suspension (IRS) system utilizes MacPherson struts, which fasten to axle carrier and wheel housing.
More informationkit contents trail-safe samurai inner axle seal suzuki samurai (all engines) InstalLation Instructions
InstalLation Instructions trail-safe samurai inner axle seal 300748-3-kit 1986-1995 suzuki samurai (all engines) kit contents 5356 PINE AVE FRESNO, CA 93727 USA TOLL FREE: 877.4X4.TOYS WORLDWIDE: 559.252.4950
More informationALLDATA Online Lexus LS 400 V8-4.0L (1UZ-FE) - Front. Front
Page 1 of 18 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 1991 Lexus LS 400 V8-4.0L (1UZ-FE) Conversion Calculator Vehicle
More informationDF 47 DIFFERENTIAL REAR DIFFERENTIAL CARRIER ASSEMBLY REMOVAL
47 REMOVAL 1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL 2. REMOVE REAR WHEEL 3. DRAIN BRAKE FLUID Immediately wash off any brake fluid that comes into contact with any painted surfaces. 4. DRAIN
More informationFront and Rear Suspension Modification Kit Installation
Page 1 of 12 2014 Chevrolet Sonic (US/Canada) Sonic US/Canada Accessory Installation Manual Accessories Performance Accessories Accessories Document ID: 3471343 Front and Rear Suspension Modification Kit
More informationParking Brake Shoe: Adjustments
1997 Ford Truck F 350 2WD Pickup V8-460 7.5L VIN G EFI Copyright 2007, ALLDATA 9.50 Page 1 Parking Brake Shoe: Adjustments Transmission-Mounted Parking Brake Disassembly 1. Remove the Parking brake assembly
More informationDifferential Bearings
SECTION 205-02A: Rear Drive Axle/Differential Ford 7.5-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 04/02/2009 Differential Bearings Special Tool(s) 2 Jaw Puller
More informationWD Dodge Suspension Kit
92137600 02-05 2WD Dodge 1500 6 Suspension Kit Thank you for choosing Rough Country for your suspension needs. Rough Country recommends a certified technician installs this system. In addition to these
More informationPage 1 of 5 Section 05-03A: Axle, Front Drive, Dana Models 44 and 50 1996 Bronco/F-Series Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/19/2000 Spindle, RH and LH Shaft and Joint
More information3. Front Axle FRONT AXLE. A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. DS-17
FRONT AXLE DRIVE SHAFT SYSTEM 3. Front Axle A: REMOVAL 1) Lift-up the vehicle and remove the front wheels. 2) Unlock the axle nut. 6) Remove the disc rotor from hub. If the disc rotor seizes up within
More informationBRAKE SYSTEM Toyota Celica DESCRIPTION DRUM BRAKES ADJUSTMENTS BRAKE PEDAL HEIGHT ADJUSTMENTS BRAKE PEDAL FREE PLAY ADJUSTMENTS
BRAKE SYSTEM 1988 Toyota Celica 1988-89 BRAKES Toyota Celica, Corolla, MR2, Tercel DESCRIPTION The hydraulic brake system uses a tandem master cylinder with a vacuum power assist servo. MR2 and some Celica
More informationFront Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014. Axle
204-01 Front Suspension 2015 E-Series REMOVAL AND INSTALLATION Procedure revision date: 08/11/2014 Axle 1 N620604 Axle pivot nut 2 N806859 Axle pivot bolt 3 3007 LH/ 3006 RH LH/ 3006 RH Axle Removal NOTICE:
More informationFront Wheel Bearing - New Replacement Procedures 55E230 APRIL Eagle Comanche Cherokee-Wagoneer 1987 Wrangler-YJ
1987 Jeep Truck Wrangler L4-150 2.5L VIN H TBI Copyright 2013, ALLDATA 10.52SS Page 1 Technical Service Bulletin # 55E230 Date: 870401 Front Wheel Bearing - New Replacement Procedures 55E230 APRIL 1987
More informationOff-Highway Axle Planetary Wheel Ends
Maintenance Manual MM-1189 Off-Highway Axle Planetary Wheel Ends Revised 06-16 Service Notes About This Manual This manual provides service and repair procedures for planetary wheel ends on off-highway
More informationInstallation Instructions
Installation Instructions 6 Suspension System FTS25005BK / FTS25006BK 2006-2012 Nissan Frontier 2wd/4wd SHORT BED ONLY Tool List: (not included) Floor Jack & Jack Stands Assorted Metric & S.A.E Sockets
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2005 2010 DROPPED SPINDLE DATSUN 720 2 WHEEL DRIVE PICK-UPS NISSAN HARDBODY 2WD PICK-UPS Congratulations! You were selective enough to choose a BELLTECH PRODUCT. We have spent
More informationFox 2.0 Adjustable Coilovers (Par# ) Installation on a 2013 F-150 (2WD)
Fox 2.0 Adjustable Coilovers (Par# 983-02-052-2) Installation on a 2013 F-150 (2WD) This guide is for the install of the Fox 2.0 adjustable leveling struts on a 2013 F-150 2WD, these are being installed
More informationWheel end bearing and seal installation guide. Automotive edition Featuring front and rear wheel drive models
Wheel end bearing and seal installation guide Automotive edition Featuring front and rear wheel drive models Introduction Contents The SKF Seal and Bearing lnstallation Guide (SKF #457809) covers the removal
More informationWheel Hub: Service and Repair Front
2004 Acura Truck MDX V6-3471cc 3.5L Copyright 2009, ALLDATA 10.10 Page 1 Wheel Hub: Service and Repair Front Knuckle/Hub Replacement Special Tools Required - Ball joint remover, 28 mm 07MAC-SL00200 - Hub
More information07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES
MAXTRAC SUSPENSION 4030 E LEAVERTON CT ANAHEIM, CA 92807 714-630-0363 WWW.MAXTRACSUSPENSION.COM SALES@MAXTRACSUSPENSION.COM PRODUCT: K886764 07-13 TOYOTA TUNDRA 2WD 6" LIFT SPINDLES PARTS LIST QTY LIFT
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767 3100-3200 3 DROPPED FRONT SPINDLE 73-87 1/2 TON C-10 PICK-UP / 1/2 TON BLAZER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2100 DROPPED FRONT SPINDLE CHEVROLET 2WD S-10 / S-15 PICKUP / BLAZER / JIMMY, including models with ABS General Motors G-Body Rear Wheel Drive Cars CONGRATULATIONS! You were selective
More informationBRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
More informationFRONT & 4 REAR GM WD LOWERING KIT
92725200 88-98 2 FRONT & 4 REAR GM 1500 2WD LOWERING KIT Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition
More informationPleasereadandfulyunderstandthisprocedurepriortoperforminganybearingmaintenance.
Pleasereadandfulyunderstandthisprocedurepriortoperforminganybearingmaintenance. Thismanualoutlinesgeneraldirectionsforbearingmaintenanceusingtestedefective techniques.additionaly,alcommonandacceptedsafetypracticesaretobefolowedin
More informationFRONT & REAR AXLE SECTIONAX CONTENTS. FRONT AXLE...2 Precautions...2
FRONT & REAR AXLE SECTIONAX CONTENTS FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness (NVH) Troubleshooting...3
More informationTECHNICAL BULLETIN. Servicing Meritor TM EASY STEER PLUS TM Series Unitized Truck Hub Unit Assembly
TP-9819 Revised 12-97 TECHNICAL BULLETIN Servicing Meritor TM EASY STEER PLUS TM Series Unitized Truck Hub Unit Assembly Attention Freightliner dealers and direct warranty customers. Please discard this
More information2000 F-Super Duty /Excursion/F-53 Motorhome Chassis Workshop Manual
Page 1 of 6 SECTION 205-02E: Wheel Hubs and Bearings Full Floating Axle Ford 2000 F-Super Duty 250-550/Excursion/F-53 Motorhome Chassis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date:
More informationFRONT AXLE GROUP 11A CONTENTS 11A-0. SECTION 0 GENERAL Removal 3 SECTION 1 FRONT AXLE HUB 1
11A-0 GROUP 11A FRONT AXLE CONTENTS SECTION 0 GENERAL 1 1-1 Removal 3 SECTION 1 FRONT AXLE HUB 1 1-2 Inspection 3 1-3 Installation 4 1. Removal and Installation 1 1-1 Removal 1 SECTION 3 WHEEL ALIGNMENT
More informationSAFETY RECALL Volvo Trucks North America Greensboro, NC USA
SAFETY RECALL Greensboro, NC USA This Safety Recall replaces recall, RVXX1403, Disc Brake Caliper Bolts, Dated (10.2014). Date Number Release Page 12.2014 1 (11) RVXX1403 02 DISC BRAKE CALIPER BOLTS VAH,
More informationInspection and Verification, Ranger
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svk53a03.htm~gen~ref.htm Page 1 of 1 Section 05-03A: Wheel Hubs and Bearings, Front Wheels, 4- Wheel Drive DIAGNOSIS AND TESTING 1997 Ranger 4x4 with Dana
More informationINSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA
INSTALLATION INSTRUCTIONS: LONG TRAVEL KIT 07+ FJ CRUISER and 05+ TACOMA ISNTALLATION DIFFICULTY: Advanced APPROX TIME: 6-8 Hours REQUIRED TOOLS: 14mm-35mm sockets, wrenches, and ratchet 9/16 and 5/8 12
More informationService Parts Instructions
Issued 07-00 Service Parts Instructions RPL Series Permalube TM Generation II Driveline Removal and Installation WARNING To prevent serious eye injury, always wear safe eye protection when you perform
More informationFRONT DROP SPINDLES
92725000 88-98 2 FRONT DROP SPINDLES Thank you for choosing Rough Country for all your suspension needs. Rough Country recommends a certified technician install this system. In addition to these instructions,
More informationBrake Pad: Service and Repair Front PADS - BRAKE FRONT
2005 Dodge Truck RAM 3500 4WD Pickup L6-5.9L DSL Turbo VIN C Page 1 Brake Pad: Service and Repair Front PADS - BRAKE FRONT REMOVAL 1. Raise and support vehicle. 2. Remove the wheel and tire assemblies.
More informationBRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM
Article Text ARTICLE BEGINNING 1992 BRAKES Chrysler Motors/Mitsubishi - Disc & Drum Chrysler Motors: Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon; Mitsubishi: Diamante, Eclipse, Expo/Expo
More informationFRONT AXLE AND SUSPENSION FA 1
FRONT AXLE AND SUSPENSION FA1 FRONT AXLE AND SUSPENSION FA2 FRONT AXLE AND SUSPENSION Troubleshooting TROUBLESHOOTING Problem Possible cause Remedy Page Wanders/pulls Tires worn or improperly inflated
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any
More informationSTOP---READ THIS FIRST!
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2007-2013 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART# 50700 & 50720) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196
More informationRHINO SUSPENSION SYSTEM INSTALLATION INSTRUCTIONS
PARTS INCLUDED: 2 FRONT UPPER A-ARMS 2 FRONT LOWER A-ARMS 2 UNI-BALL JOINTS 2 UNI-BALL JOINT STUDS 2 UNI-BALL JOINT CAPS 2 RETAINING RINGS 1 FRONT SHOCK ASSEM. 2 DELRON STEERING STOPS 2 SHOCK MOUNT SPACERS
More information1999 Toyota RAV DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2. AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2
1999-2000 DRIVE AXLES AWD & FWD Axle Shafts - RAV4 & RWD Axle Shafts - MR2 DESCRIPTION & OPERATION On RAV4 models, axle shafts transfer power from transaxle to front wheels (FWD), or front and rear wheels
More information2014 GM 1500 TRUCK STOP---READ THIS FIRST! 7" Lift KIT. **Read These Entire Instructions Before Starting Anything**
STOP---READ THIS FIRST! **Read These Entire Instructions Before Starting Anything** 2014 GM 1500 TRUCK LIFT KIT INSTRUCTIONS (PART #50768 & #50769 ) 5680 W. Barstow, Fresno, CA 93722 PH: (559) 226-8196
More information1 of 25 9/12/2013 9:07 PM
1 of 25 9/12/2013 9:07 PM 46RE Automatic Transmission DISASSEMBLY 1. Clean exterior of transmission with suitable solvent or pressure washer. 2. Place transmission in vertical position. 3. Measure the
More information'88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N
4/10/13 '88-'00 CHEVROLET/GMC IFS 4WD(8LUG) OLD BODY STYLE 6" SUSPENSION SYSTEM P/N. 10-41888 INSTALLATION INSTRUCTIONS APPLICATION WARNING: Applicable for hub mounted ABS sensor models only. Not for 1992-94
More informationDRIVE AXLE Nissan 240SX DESCRIPTION & OPERATION AXLE RATIO & IDENTIFICATION AXLE SHAFT & BEARING R & I DRIVE SHAFT R & I
DRIVE AXLE 1990 Nissan 240SX 1990 DRIVE AXLES Rear Axle - R200 240SX, 300ZX DESCRIPTION & OPERATION The axle assembly is a hypoid type gear with integral carrier housing. The pinion bearing preload adjustment
More information5. Front Drive Shaft FRONT DRIVE SHAFT. B: INSTALLATION 1) Insert the BJ into hub splines.
5. Front Drive Shaft A: REMOVAL 1) Jack-up the vehicle, support it with rigid racks, and then remove the front wheel cap and wheels. 2) Raise the caulking portion of axle nut. 3) Depress the brake pedal
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2000 1984 1991 Toyota 2 Wheel Drive Pick-Ups 2 Front Dropped Spindles Congratulations!
More informationREAR HUB UNIT BEARING
2014 Subaru Forester F4-2.5L DOHC Vehicle > Steering and Suspension > Wheels and Tires > Wheel Bearing > Service and Repair > Removal and Replacement REAR HUB UNIT BEARING Rear Hub Unit Bearing REMOVAL
More informationDetroit Speed, Inc. Rear Cradle Mounts Camaro P/N:
Detroit Speed, Inc. Rear Cradle Mounts 2010-15 Camaro P/N: 041510 Replace the weak, compliant factory rear cradle mounts in your 2010-15 Camaro with Detroit Speed s Solid Rear Cradle Mounts, and completely
More informationPRE-INSTALLATION. INSTALLATION INSTRUCTIONS Front Ford F150 4WD 4" Suspension Lift Kit
2015 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front Brake Line
More informationPRE-INSTALLATION Ford F150 4WD 4" Suspension Lift Kit
2009-2013 Ford F150 4WD 4" Suspension Lift Kit PRE-INSTALLATION 25007 2 - Knuckle (Driv/Pass) 2 - Crossmember (Front/Rear) 2 - Differential Bracket (Driv/Pass) 1 - Diff. Brace Bracket (Pass) 2 - Front
More informationTABLE OF CONTENTS 0 FRONT DRIVE , WHEEL HUB , WHEEL HUB BEARING , KNUCKLE
Subsection 01 (TABLE OF CONTENTS) TABLE OF CONTENTS 0 FRONT DRIVE... 06-02-1 1, WHEEL HUB... 06-02-2 2, WHEEL HUB BEARING... 06-02-2, KNUCKLE... 06-02- FINAL DRIVE... 06-0-1 1, DRIVE CHAIN... 06-0-2 2,
More informationnissan patrol birfield kit
nissan patrol birfield kit 300795-kit 1987-1997 nissan patrol gr(y60) 1988-1994 ford maverick 1987-1997 nissan patrol gq 1987-1997 nissan patrol safari 1987-1997 nissan safari kit contents 5356 PINE AVE
More information'99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N INSTALLATION INSTRUCTIONS
1/16/04 '99-03 CHEVROLET/GMC IFS 4WD 6" SUSPENSION SYSTEM P/N. 10-41099 INSTALLATION INSTRUCTIONS NOTE: Each Lift Kit and options to Lift Kits are packaged separately. Therefore, installation procedures
More informationDifferential Bearings
SECTION 205-02B: Rear Drive Axle/Differential Ford 8.8-Inch Ring Gear 2009 Mustang Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 01/06/2010 Differential Bearings Special Tool(s) 2 Jaw Puller
More informationTrim Panel: Service and Repair. Garnish Molding Replacement - Center Pillar
2004 Chevy Truck Silverado 1500 2WD V8-5.3L VIN T Copyright 2013, ALLDATA 10.52 Page 1 Trim Panel: Service and Repair Garnish Molding Replacement - Center Pillar Garnish Molding Replacement - Center Pillar
More informationSteer Axles. Spicer. Service Manual. AXSM-0070 November Front Drive Steer Axle Model 60
Spicer Steer Axles Service Manual AXSM-0070 November 2017 Front Drive Steer Axle Model 60 General Information The description and specifications contained in this service publication are current at the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO
More informationElectric to Hydraulic Disc Brake Conversion
Electric to Hydraulic Disc Brake Conversion Installation and Owner s Manual (For Aftermarket Applications) Table of Contents Introduction... 1 Document Information... 1 Trailer Axle Brake Inspection...
More informationDRIVE AXLES. Differentials & Axle Shafts - Corvette
DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case
More informationWARNING: Only perform this installation if you are experienced, fully equipped mechanic.
DYNATRAC V3.2 2005-Present Ford Super Duty 250/350-4x4, Front Axle, Free Spin Conversion Kit Some of the less common tools, which will be required: 6 point Spanner socket (OTC #7090-A or equivalent). These
More informationMASTER CYLINDER INSPECTION
7-16 CHASSIS A-PDF Split DEMO : Purchase from www.a-pdf.com to remove the watermark Remove the piston assembly. MASTER CYLINDER INSPECTION MASTER CYLINDER Inspect the master cylinder bore for any scratches
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More informationBMW 3 Series E46 Front Wheel Bearing
BMW 3 Series E46 Front Wheel Bearing Replacement A step-by-step guide on BMW 3 Series E46 Front Wheel Bearing Replacement. Written By: Danielle 2017 guides.drivediy.com Page 1 of 13 INTRODUCTION Discover
More informationSlide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided.
Slide the billet aluminum cap over the bushing and secure with the 3/8-16 x 2 1/2 socket head allen and locknuts provided. Put the urethane bushings into the upper antiroll-bar-link eyebolt. Coat the bushings
More informationSECTION RA CONTENTS REAR AXLE & REAR SUSPENSION IDX
CONTENTS REAR AXLE & REAR SUSPENSION SECTION RA GI MA EM LC EC FE PRECAUTIONS AND PREPARATION...2 Precautions...2 Special Service Tools...2 Commercial Service Tools...3 NOISE, VIBRATION AND HARSHNESS (NVH)
More informationFRONT & REAR AXLE SECTIONAX CONTENTS IDX. FRONT AXLE...2 Precautions...2
FRONT & REAR AXLE SECTIONAX GI MA EM LC EC CONTENTS FE FRONT AXLE...2 Precautions...2 PRECAUTIONS...2 Preparation...2 SPECIAL SERVICE TOOLS...2 COMMERCIAL SERVICE TOOLS...2 Noise, Vibration and Harshness
More informationFORD RACING DIFFERENTIAL COVER 8.8 IRS
FORD RACING DIFFERENTIAL COVER 8.8 IRS Tools Needed: Socket set, metric and standard Sledge hammer Puller device, pitman puller Jack Jack stands Flat head screw drivers Torque wrench, capable of 8 ft/lbs
More informationSECTION C: Wheel Hubs and Bearings Full Floating Axle Dana
SECTION 205-02C: Wheel Hubs and Bearings Full Floating Axle Dana REMOVAL AND INSTALLATION 2007 F-53 Motorhome Chassis Workshop Manual Procedure revision date: 12/04/2006 Wheel Hub Material Item Premium
More information1 of 15 1/26/2017 8:57 AM
1 of 15 1/26/2017 8:57 AM Timing Belt and Balancer Belt Removal Special Tools Required ^ Holder Handle 07JAB-001020A ^ Holder Attachment, 50 mm, Offset 07MAB-PY3010A ^ Socket, 19 mm 07JAA-001020A or a
More informationReplacing the hub oil seal.
Replacing the hub oil seal. The most common reason for hub oil seal failure is a blocked axle breather, so check this first before you start. Remove the brass bell-shaped fitting on the top of the axle,
More informationWheel bearing housing, removing and installing
Page 1 of 17 40-54 Wheel bearing housing, removing and installing Removing - Remove wheel trim. On light alloy wheels use puller in vehicle tool kit to remove trim cap. - Remove bolt for drive axle. WARNING!
More informationFull Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra)
Full Tilt Boogie (FTBR) Subframe Bushing Kit Install (99-04 Cobra) Tools Required: Jack and jack stands (Or a lift) Metric sockets 8,12,15,18,21mm and a 12pt 12mm socket for driveshaft bolts T40 torx bit
More informationRekluse Motor Sports. The e-axle KTM. Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.
Rekluse Motor Sports The e-axle 2003 2007 KTM Installation Guide Copyright 2006 Rekluse Motor Sports e-axle Revision 1.000 RMS 2733 195-2733C Manual Revision: 032207 Rekluse Motor Sports, Inc. 110 E. 43
More informationMustang Differential Gears - Installation Instructions
Mustang Differential Gears - Installation Instructions The below installation instructions work for the following products: Ford Racing Gears - 3.73 Gears for 8.8" Ford Rear End Ford Racing Gears - FRPP
More informationInstallation Instructions. 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK GM 2WD C1500 P/U ONLY
Installation Instructions 6 Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500 P/U ONLY 2007-13 GM 1500 Truck Basic System FTS21060BK / FTS21061BK / FTS21042BK 2007-13 GM 2WD C1500
More informationFORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1)
FORD RACING DIFFERENTIAL INSTALLATION (99-04 GT, Mach 1) Time Necessary: Approximately 4 hours Tools Required: Wrenches: 8mm, 13mm, 15mm, 5.5 mm allen, 6mm allen Sockets: 5/8, 3/4 Ratchet Floor Jack Jack
More information