Automatic Transmission/Transaxle: Removal and Replacement Transmission Replacement
|
|
- Neil Berry
- 6 years ago
- Views:
Transcription
1 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 1 Automatic Transmission/Transaxle: Removal and Replacement Transmission Replacement Transmission Replacement Tools Required * J B Cooler Quick Connect Tool * J Steering Column Anti-Rotation Pin Removal Procedure Notice: The wheels of the vehicle must be straight ahead and the steering column in the LOCK position before disconnecting the steering column or intermediate shaft from the steering gear. Failure to do so will cause the SIR coil assembly to become uncentered, which may cause damage to the coil assembly. 1. Lock the steering column by installingj into the underside of the steering column. 2. Disconnect the negative battery cable. Refer to Battery Negative Cable Replacement (See: Starting and Charging/Battery/Battery Cable/Negative/Service and Repair). 3. Remove the front compartment sight shield. Refer to Front Compartment Sight Shields Replacement (See: Body and Frame/Spoilers, Flaps, and Air Dams/Air Dam/Service and Repair/Front Compartment Sight Shields Replacement). 4. Remove the air cleaner assembly. Refer to Air Cleaner Assembly Replacement (See: Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance Checks/Air Cleaner Housing/Service and Repair). 5. Remove the range select cable terminal from the transaxle range select lever. 6. Remove the range selector cable bracket nuts. 7. Remove the range selector cable with bracket from the transmission case and position aside.
2 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 2 8. Disconnect the transaxle electrical connector C100 (2). 9. Remove the wiring harness (3) from the wiring harness retainer (1) on the transaxle. 10. Remove the ground cable bolt (1) from the transaxle. 11. Install the engine support fixture. Refer to Engine Support Fixture (See: Engine, Cooling and Exhaust/Engine/Service and Repair/Removal and Replacement/Engine Support Fixture). 12. Remove the upper engine to transaxle case bolts (2-5). 13. Raise and Support the vehicle. Refer to Lifting and Jacking the Vehicle (See: Maintenance/Vehicle Lifting/Service and Repair). 14. Remove the front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair).
3 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page Remove the left front wheelhouse liner (1). Refer to Front Wheelhouse Liner Replacement (See: Body and Frame/Fender/Front Fender/Front Fender Liner/Service and Repair). 16. Remove the front air deflector. Refer to Front Air Deflector Replacement (See: Body and Frame/Spoilers, Flaps, and Air Dams/Air Dam/Service and Repair/Front Air Deflector Replacement). 17. Remove the stabilizer shaft links. Refer to Stabilizer Shaft Link Replacement (See: Steering and Suspension/Suspension/Stabilizer Bar/Stabilizer Link/Service and Repair/Front Suspension). 18. Swing the stabilizer shaft downward in order to gain access to the power steering gear retaining bolts.
4 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 4 Caution: Failure to disconnect the intermediate shaft from the rack and pinion steering gear stub shaft can result in damage to the steering gear or to the intermediate shaft. This damage may cause loss of steering control, which could result in an accident and possible personal injury. 19. Remove the intermediate shaft lower pinch bolt. 20. Disconnect the intermediate shaft from the power steering gear. 21. Remove the power steering gear heat shield. Refer to Steering Gear Heat Shield Replacement (See: Steering and Suspension/Steering/Steering Gear/Service and Repair). 22. Remove the power steering gear mounting bolts. 23. Remove the power steering line retainers from the frame. 24. Secure the power steering gear to the exhaust manifold. 25. Remove the mounting bolts (2) in order to allow removal of the brake pressure modulator valve from the bracket. 26. Remove the brake line retainers (1) from the frame.
5 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 5 Important: The following are exceptions while following the frame removal procedure: * Do not remove the front stabilizer shaft from the frame. * Do not remove the insulators from the frame. * Do not remove the control arms from the frame. 27. Remove the frame. Refer to Front Frame Replacement (3.8L) ()Front Frame Replacement (4.6L) (See: Body and Frame/Frame/Subframe/Front Subframe/Service and Repair/Front Frame Replacement (4.6L)). 28. Remove the right and left drive axles from the transaxle. Refer to Wheel Drive Shaft Replacement (See: Drive Axles, Bearings and Joints/Axle Shaft Assembly/Service and Repair). 29. Disconnect the transmission oil cooler hoses from the transaxle using the J B. Refer to Transmission Fluid Cooler Hose/Pipe Replacement (See: Fluid Line/Hose/Service and Repair). 30. Remove the transaxle fluid filler tube. Refer to Transmission Fluid Filler Tube and Seal Replacement (See: Automatic Transmission Dipstick - Dipstick Tube/Service and Repair/4T65-E - Automatic Transaxle). 31. Remove the torque converter cover. Refer to Torque Converter Cover Replacement (See: Torque Converter Cover/Service and Repair/4T65-E - Automatic Transaxle). 32. Mark the flywheel to converter relationship to ensure proper reassembly. Remove the flywheel to torque converter bolts (1). 33. Support transaxle using an appropriate transaxle jack. 34. Disconnect vehicle speed sensor electrical connector.
6 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page Remove the right engine to transaxle brace bolts (1). 36. Remove the front transaxle to engine brace bolt (1).
7 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page Remove the engine to transaxle case bolt (6) which is accessible through right wheel opening. 38. Remove the remaining transaxle to engine bolt (1). 39. Remove the transaxle from vehicle using an appropriate transaxle jack. 40. Remove the rear transaxle mount bracket from the transaxle.
8 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page Remove the left transaxle mount bracket from the transaxle. 42. Flush the transmission cooler and lines. Refer to Transmission Fluid Cooler Flushing and Flow Test (J35944-A) (See: Testing and Inspection/Component Tests and General Diagnostics/4T65-E Automatic Transaxle/Automatic Transmission Oil Cooler Flushing and Flow Test (J35944-A))Transmission Fluid Cooler Flushing and Flow Test (J45096) (See: Testing and Inspection/Component Tests and General Diagnostics/4T65-E Automatic Transaxle/Automatic Transmission Oil Cooler Flushing and Flow Test (J-45096)). nstallation Procedure 1. Install the left transaxle mount bracket to the transaxle. Notice: Refer to Fastener Notice (See: Service Precautions/Vehicle Damage Warnings/Fastener Notice). 2. Install the left transaxle bracket bolts. Tighten the bolts to 70 N.m (52 lb ft).
9 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 9 3. Install the rear transaxle mount bracket to the transaxle. 4. Install the rear transaxle mount bracket bolts. Tighten the bolts to 50 N.m (37 lb ft). 5. Install the transaxle into the vehicle and align the engine alignment dowels (1 and 5). 6. Install the transaxle case to engine bolts (1 and 6).
10 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 10 Tighten the bolts to 75 N.m (55 lb ft). 7. Install the front transaxle to engine brace bolt (1). Tighten the bolt to 50 N.m (37 lb ft). 8. Install the right engine to transaxle brace bolts (1). Tighten the bolts to 50 N.m (37 lb ft). 9. Connect vehicle speed sensor electrical connector. 10. Remove the transaxle jack
11 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 11 Important: * Align the mark made on the torque converter with the mark made on the flywheel made in the disassembly unless installing a new converter. * Tighten all the torque converter to flywheel bolts twice. 11. Install the flywheel to torque converter bolts (1). Tighten the bolts to 63 N.m (47 lb ft). 12. Install the torque converter cover. Refer to Torque Converter Cover Replacement (See: Torque Converter Cover/Service and Repair/4T65-E - Automatic Transaxle). 13. Install the transaxle fluid filler tube. Refer to Transmission Fluid Filler Tube and Seal Replacement (See: Automatic Transmission Dipstick - Dipstick Tube/Service and Repair/4T65-E - Automatic Transaxle). 14. Connect the transmission oil cooler hoses to the transaxle. Refer to Transmission Fluid Cooler Hose/Pipe Replacement (See: Fluid Line/Hose/Service and Repair). Important: Use care when installing the right side drive axle into the transaxle case. The splined shaft of the drive axle can easily damage the seal. 15. Install the left and the right drive axle into the transaxle. Refer to Wheel Drive Shaft Replacement (See: Drive Axles, Bearings and Joints/Axle Shaft Assembly/Service and Repair). 16. Install the front frame assembly to the vehicle. Refer to Front Frame Replacement (3.8L) ()Front Frame Replacement (4.6L) (See: Body and Frame/Frame/Subframe/Front Subframe/Service and Repair/Front Frame Replacement (4.6L)). 17. Install the left transaxle mount. Refer to Transmission Mount Replacement - Left Side (See: Transmission Mount/Service and Repair/4T65-E - Automatic Transmission/Transmission Mount Replacement - Left Side).
12 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page Position the brake pressure modulator valve into the bracket. 19. Install the mounting bolt (2). Tighten the bolt to 10 N.m (89 lb in). 20. Install the brake line retainers (1) onto the frame. 21. Install the power steering gear mounting bolts. Tighten the bolts to 75 N.m (55 lb ft). 22. Install the power steering line retainers onto the frame. 23. Install the power steering gear heat shield. Refer to Steering Gear Heat Shield Replacement (See: Steering and Suspension/Steering/Steering Gear/Service and Repair).
13 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 13 Caution: When installing the intermediate shaft make sure that the shaft is seated prior to pinch bolt installation. If the pinch bolt is inserted into the coupling before shaft installation, the two mating shafts may disengage. Disengagement of the two mating shafts will cause loss of steering control which could result in personal injury. 24. Connect the intermediate shaft to the power steering gear. 25. Install the intermediate shaft lower pinch bolt. Tighten the bolt to 45 N.m (33 lb ft). 26. Install the stabilizer shaft links. Refer to Stabilizer Shaft Link Replacement (See: Steering and Suspension/Suspension/Stabilizer Bar/Stabilizer Link/Service and Repair/Front Suspension). 27. Install the air deflector extension. Refer to Front Air Deflector Replacement (See: Body and Frame/Spoilers, Flaps, and Air Dams/Air Dam/Service and Repair/Front Air Deflector Replacement). 28. Install the left front wheelhouse liner (1). Refer to Front Wheelhouse Liner Replacement (See: Body and Frame/Fender/Front Fender/Front
14 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page 14 Fender Liner/Service and Repair). 29. Install the front tire and wheel assembly. Refer to Tire and Wheel Removal and Installation (See: Maintenance/Wheels and Tires/Service and Repair). 30. Lower the vehicle. 31. Install the upper transaxle case to engine bolts (2-5). Tighten the bolts to 75 N.m (55 lb ft). 32. Remove the engine support fixture. 33. Install the range selector cable with bracket. 34. Install the range selector cable bracket nuts. Tighten the nuts to 25 N.m (18 lb ft). 35. Install the range selector cable onto the range selector lever. 36. Check adjustment of the range selector cable. Re-adjust as needed. Refer to Range Selector Lever Cable Adjustment (See: Shift Linkage/Shift Cable/Adjustments).
15 2008 Buick Lucerne V8-4.6L Copyright 2013, ALLDATA Page Install ground cable and bolt (1) to transaxle. Tighten the bolt to 17 N.m (13 lb ft). 38. Connect the transaxle electrical connector C100 (2). 39. Install the wiring harness (3) into the wiring harness retainer (1) on the transaxle. 40. Install the air cleaner assembly. Refer to Air Cleaner Assembly Replacement (See: Engine, Cooling and Exhaust/Engine/Tune-up and Engine Performance Checks/Air Cleaner Housing/Service and Repair). 41. Install the front compartment sight shield. Refer to Front Compartment Sight Shields Replacement (See: Body and Frame/Spoilers, Flaps, and Air Dams/Air Dam/Service and Repair/Front Compartment Sight Shields Replacement). 42. Connect the negative battery cable. Refer to Battery Negative Cable Replacement (See: Starting and Charging/Battery/Battery Cable/Negative/Service and Repair). 43. Remove the J from the steering column. 44. Fill the transaxle to the proper level. Refer to Fluid Capacity Specifications. 45. Inspect the transaxle fluid level. Refer to Transmission Fluid Check (See: Fluid - A/T/Testing and Inspection/4T65-E Automatic Transaxle). 46. Inspect for fluid leaks. 47. Clear transmission adaptive pressures (TAPS). Refer to Transmission Adaptive Functions (See: Description and Operation/4T65-E Automatic Transaxle/Transmission Adaptive Functions). 48. Check the front end alignment. 49. Road test the vehicle and check for transaxle leaks.
3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationSteering Gear Replacement
Page 1 of 7 Steering Gear Replacement Removal Procedure Notice: With wheels of the vehicle facing straight ahead, secure the steering wheel utilizing steering column anti-rotation pin, steering column
More information1 of 11 7/11/2015 6:48 AM
1 of 11 7/11/2015 6:48 AM 43. Disconnect the A/C pressure sensor. 44. Disconnect the A/C discharge hose from the compressor and secure to the cooling fan assembly. 45. Disconnect the A/C suction hose from
More informationGM 4T65E Installation Tips
GM 4T65E Installation Tips WARNING: DO NOT operate vehicle without installing a new transmission oil cooler. We recommend installing a Hayden 1403 or 1404. Bypass the radiator and install the new cooler.
More informationALLDATA Online Chevy Truck Avalanche WD V8-5.3L VIN T - Steering... Page 1 of 12. Steering Wheel Module Coil Replacement (Coil)
ALLDATA Online - 2006 Chevy Truck Avalanche 1500 2WD V8-5.3L VIN T - Steering... Page 1 of 12 Steering Wheel Module Coil Replacement (Coil) INFLATABLE RESTRAINT STEERING WHEEL MODULE COIL REPLACEMENT (COIL)
More information2008 Saturn Aura V6-3.6L
1 of 14 7/17/2016 7:26 PM 2008 Saturn Aura V6-3.6L Vehicle» Engine, Cooling and Exhaust» Cooling System» Radiator» Service and Repair» Radiator Replacement Radiator Replacement (LY7 - Gas, 6 Cyl, 3.6L,
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More informationAxle Bearing: Service and Repair Rear Axle Hub, Bearing, Cup, and/or Seal Replacement
2011 Chevy Truck Silverado 3500 2WD V8-6.6L DSL Turbo Copyright 2013, ALLDATA 10.52 Page 1 Axle Bearing: Service and Repair Rear Axle Hub, Bearing, Cup, and/or Seal Replacement Rear Axle Hub, Bearing,
More informationIN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
More informationOil Pan Replacement Buick Regal
2000 Buick Regal Oil Pan Replacement Removal Procedure Tools Required J 28467-90A Engine Support Adapters J 28467-B Universal Engine Support Fixture J 36462-A Engine Support Adapter Leg Set 1. Disconnect
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More informationVehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More information1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder
ENGINE IDENTIFICATION 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder For engine repair procedures not covered in this article, see ENGINE OVERHAUL PROCEDURES - GENERAL INFORMATION article in the GENERAL INFORMATION
More informationALLDATA Online Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12. Service and Repair
ALLDATA Online - 2000 Chevy Truck S10/T10 P/U 2WD L4-2.2L VIN 4 - Service and... Page 1 of 12 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationFront Bumper Fascia Replacement
Page 1 of 10 2008 Pontiac G8 G8 Service Manual Body Repair Bumpers and Fascias Repair Instructions Document ID: 2044380 Front Bumper Fascia Replacement Removal Procedure Caution: Refer to Safety Glasses
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More information2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
More informationAutomatic Transmission Assembly Remove and Install (2,9 V6 24V engine) ( ) Remove
Automatic Transmission Assembly Remove and Install (,9 V6 4V engine) (7 4 0) Special Tools -40 Engine support bar -40-0 Adaptor for -40-40-03 Adaptor for -40 Workshop Equipment Transmission jack Materials
More information7. Remove the starter motor. Refer to Starter Motor Replacement (2.2L) or Starter Motor Replacement (4.3L).
1 of 9 1/5/2013 6:40 PM Removal Procedure 1. Disconnect the battery negative cable. Refer to Battery Replacement. 2. Remove the hood. Refer to Hood Replacement. 3. If the vehicle is equipped with a manual
More informationPage 1 of 5 2004 Pontiac GRAND PRIX Submodel: Engine Type: V6 Liters: 3.8 Fuel Delivery: FI Fuel: GAS Oil Pan Replacement Removal Procedure Disconnect the negative battery cable. Refer to Battery Negative
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More informationTiming Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: , Removal
2003 Volvo XC90 T6 AWD L6-2.9L Turbo VIN 91 B6294T Copyright 2009, ALLDATA 10.10 Page 1 Timing Belt: Service and Repair Replacing the Timing Belt Timing belt, replacing Special tools: 999 5433, 999 5456
More informationfile://c:\program Files\tsocache\OFFICE_2780\SXN~us~en~file=SXNB2012.htm~gen~ref...
Page 1 of 14 SECTION 211-02: Power Steering 1999 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 07/27/1998 Gear 5.0L Removal 1. Place the front wheels in the straight
More information1 of 7 7/22/2013 8:41 AM
1 of 7 7/22/2013 8:41 AM REMOVAL 1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead. 2. Turn the ignition switch to "LOCK". 3. Disconnect the battery "-" terminal cable,
More information2001 Chevrolet CORVETTE
riveline Support Assembly Replacement (Automatic Transmission) 1 of 21 10/24/2012 8:58 PM 2001 Chevrolet CORVETTE Submodel: Engine Type: V8 Liters: 5.7 Fuel Delivery: FI Fuel: GAS Driveline Support Assembly
More information1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
More informationSUSPENSION - FRONT Toyota Celica DESCRIPTION ADJUSTMENTS & INSPECTION WHEEL ALIGNMENT SPECIFICATIONS & PROCEDURES WHEEL BEARING
SUSPENSION - FRONT 1988 Toyota Celica FRONT SUSPENSION Toyota DESCRIPTION Vehicles are equipped with front wheel drive and independent MacPherson strut front suspension. Suspension consists of vertically
More information1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT
Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage
More informationSECTION Automatic Transaxle/Transmission 4R70E/4R75E
307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic
More informationPage 1 of 14 Oil Pan Removal & Installation 4.2L Engine 4WD Vehicles To Remove: 1. Before servicing the vehicle refer to the precautions at the beginning of this section. 2. Raise and support the vehicle.
More informationSTEERING COLUMN REPLACEMENT (... STEERING COLUMN REPLACEMENT (ELECTRONIC) (STEERING WHEEL AND COLUMN) Document ID#
STEERING COLUMN REPLACEMENT (... STEERING COLUMN REPLACEMENT (ELECTRONIC) (STEERING WHEEL AND COLUMN) Document ID# 1641009 Steering Column Replacement (Electronic) Removal Procedure Caution: Refer to SIR
More informationTransmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
More informationEngine, removing and installing
Стр 1 из 16 10-1 Engine, removing and installing Special tools, testers and auxiliary items required Torque wrench VAG 1331 Torque wrench VAG 1332 Engine/transmission jack VAG 1383 A Spring type clip pliers
More informationIMPORTANT: When replacing the ignition lock cylinder only, the passlock relearn procedure is not required.
A 1 of 11 2/18/2012 3:27 PM IMPORTANT: The important statement at the beginning of the "Ignition Lock Cylinder removal procedure on page 188 in the 2000/2001 Saturn S-Series Body/Electrical Volume II Service
More informationTiming Chain: Service and Repair
2005 Nissan-Datsun Altima L4-2.5L (QR25DE) Copyright 2013, ALLDATA 10.52SS Page 1 Timing Chain: Service and Repair TIMING CHAIN Removal and Installation Apply new engine oil to parts marked in illustration
More informationREMOVAL AND INSTALLATION
204-00-1 Suspension System 204-00-1 REMOVAL AND INSTALLATION Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm Rear Special Tool(s) 3. Remove the parts in the order indicated in the following illustrations
More informationfile://c:\program Files\tsocache\OFFICE_5164\SYA~us~en~file=SYA1C003.htm~gen~re...
Page 1 of 26 SECTION 501-12: Instrument Panel and Console 2000 Crown Victoria/Grand Marquis Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/21/1999 Instrument Panel Removal CAUTION:
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More informationPage 1 of 7 Section 07-01: Transaxle, Automatic FLC REMOVAL AND INSTALLATION 1992 Tempo/Topaz Workshop Manual Differential In Vehicle Removal Before beginning the Removal procedure, perform the following
More information1991 Volkswagen Vanagon Syncro
corner of radiator. See Fig. 1. Fig. 1: Bleeding Cooling System 2. Open bleeder valve in engine compartment (turn counterclockwise). See Fig. 1. Fill expansion tank until full. Start and run engine at
More informationFUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID#
FUEL SENDER ASSEMBLY REPLACEM... FUEL TANK REPLACEMENT (CAB/CHASSIS FRONT) (ENGINE CONTROLS 4.8L, 5.3L, AND 6.0L) Document ID# 824435 Fuel Tank Replacement (Cab/Chassis Front) Removal Procedure http://dh.identifix.com/searchfixes/index?roid=158586813&vid=2018330&vsm=4&hasbookmark=0&locationid=2#kw=fuel+pump&soption=1&vetid=8&stmode=1&paging=&smode=2&position=assetcat_9
More information2000 Ranger Workshop Manual
SECTION 211-02: Power Steering 2000 Ranger Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 06/1/1999 Gear Torsion Bar Suspension Special Tool(s) Remover, Tie Rod End 211-001 (TOOL-3290-D)
More informationPiston Cooling Nozzle, Replacement
Volvo Trucks North America Greensboro, NC USA This Service Bulletin replaces Service Bulletin 221-49, Piston Cooling, dated (1.2007), publication no. PV776-20177472. DService Bulletin Trucks Date Group
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More informationLINCOLN. Continental 1
3154_U01.qxd 8/1/03 7:28 AM Page 1 Continental 1 BRAKES...1-27 DRIVE TRAIN...1-21 ENGINE REPAIR...1-7 FUEL SYSTEM...1-20 PRECAUTIONS...1-7 SPECIFICATION CHARTS...1-2 STEERING AND SUSPENSION...1-22 A Air
More informationChevrolet Ford Dodge LCT1000--LCT RH / 47RE / 48RE E4OD / 4R100. Transmission removal, Installation And testing
ATS Transmission Procedures Chevrolet Ford Dodge LCT1000--LCT2500 47RH / 47RE / 48RE E4OD / 4R100 Transmission removal, Installation And testing Please read before any work is done Removal NOTE: NOTE:
More informationFront Door Panel: Service and Repair Front Door Trim Panel - Removal
Front Door Panel: Service and Repair Front Door Trim Panel - Removal REMOVAL Special Tools: 1. Disconnect and isolate the negative battery cable 2. Using trim stick or equivalent, disengage the two retaining
More informationBrake Shoe: Service and Repair Removal Procedure
2000 Buick Century V6-3.1L VIN J Copyright 2013, ALLDATA 10.52 Page 1 Brake Shoe: Service and Repair Removal Procedure ^ Tools Required - J38400 Brake Shoe Spanner and Spring Remover Caution: Keep fingers
More informationProperty of American Airlines
Operation and Maintenance Manual Appendix C, GM 4L6XE/4L70E Service This manual provides Maintenance and some On-Vehicle Service Information for the 4L6XE/70E series transmission. For diagnostic information,
More informationPARTIAL ENGINE ASSY COMPONENTS. Clip. Radiator Grille. Clip. Front Bumper Cover. Engine Under Cover LH. N m (kgf cm, ft lbf) : Specified torque
ENGINE MECHANICAL 1417 COMPONENTS 141FP01 Radiator Grille Front Bumper Cover Engine Under Cover RH Engine Under Cover LH A79361 962 1418 ENGINE MECHANICAL Heater Outlet Water Hose 7.0 (71, 62 in. lbf)
More informationAR46.20-P-0600P Remove/install rack-and-pinion steering
AR46.20-P-0600P Remove/install rack-and-pinion steering 11.3.10 MODEL 203 (except 203.081 /084 /087 /092 /281 /284 /287 /292) MODEL 209 P46.20-2123-09 1 Front axle carrier 23b Bolts, retaining plate to
More information1 M-3000-H4 F150 4X4 Lowering Kit
READ INSTRUCTIONS COMPLETELY THROUGH BEFORE STARTING. IT IS RECOMMENDED THAT INSTALLATION BE DONE BY A QUALIFIED MECHANIC. REPLACE ALL STOCK PARTS THAT ARE DAMAGED OR WORN. ALWAYS WEAR EYE PROTECTION.
More informationCLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica
CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationWARNING: ALWAYS relieve fuel pressure before disconnecting any fuel related component. DO NOT allow fuel to contact engine or electrical components.
4.0L V8 - VINS [K,U] Selected Block 1990 Lexus LS 400 For Lextreme Powertrain 2020 S. Hacienda Blvd. # D Hacienda Heights California 91745 Copyright 1998 Mitchell Repair Information Company, LLC Friday,
More informationSTEERING COLUMN SWITCHES
STEERING COLUMN SWITCHES 1998 Pontiac Bonneville 1998 ACCESSORIES & EQUIPMENT General Motors Corp. - Steering Column Switches Buick; LeSabre Oldsmobile; Eighty Eight, LSS & Regency Pontiac; Bonneville
More informationThe following tools will be required to perform this new service procedure outlined in this bulletin:
The following new service information outlined in this bulletin will aid technicians in removal and installation of the cylinder head without the removal of the front engine cover. The new service procedure
More informationCHEVY COLORADO GMC CANYON BODY LIFT INSTALLATION INSTRUCTIONS KIT # 10153
CHEVY COLORADO GMC CANYON BODY LIFT INSTALLATION INSTRUCTIONS 2004-2005 3 KIT # 10153 Installation of a Performance Automotive Group body lift kit will change the vehicle s center of gravity and handling
More informationTRANSMISSION REMOVAL & INSTALLATION - A/T
TRANSMISSION REMOVAL & INSTALLATION - A/T 1990 Nissan 240SX 1990 TRANSMISSION SERVICING Nissan Automatic Transmission Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX NOTE: For
More informationRemoval and Replacement
Page 1 of 10 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Suzuki Forenza L4-2.0L Conversion Calculator
More informationFour-Wheel Alignment ( )
Published: Mar 7, 2005 Four-Wheel Alignment (57.65.04) CAUTION: Make sure the vehicle is on a flat level surface. CAUTION: Make sure the tire pressures are within specification. CAUTION: Make sure that
More informationPage 1 of 7 Bumpers - Front Bumper Cover Removal and Installation Removal 1. WARNING: Do not work on or under a vehicle supported only by a jack. Always support the vehicle on safety stands. Raise and
More informationProperty of American Airlines
Maintenance / On Vehicle Service 4L6XE/70E 2013 PAGE 145 This manual provides Maintenance and some On-Vehicle Service Information for the 4L6XE/70E series transmission. For diagnostic information, refer
More informationCatalytic Converter: Service and Repair
2007 GMC Truck Envoy 4WD V8-5.3L Copyright 2009, ALLDATA 10.10 Page 1 Catalytic Converter: Service and Repair Catalytic Converter Replacement (5.3L and 6.0L Engines) Removal Procedure 1. Raise and suitably
More informationDash Board / Instrument Panel: Service and Repair
1995 Chevy Truck C 1500 P/U 2WD V8-350 5.7L VIN K TBI Copyright 2008, ALLDATA 9.90 Page 1 Dash Board / Instrument Panel: Service and Repair INSTRUMENT PANEL ASSEMBLY REPLACEMENT Remove or Disconnect 1.
More informationREPLACEMENT. 9. REMOVE TRANSMISSION CONTROL CABLE BRACKET NO.1 (a) Remove the 2 bolts and control cable bracket No.1.
AUTOMATIC TRANSMISSION / TRANS REPLACEMENT 1. REMOVE HOOD SUBASSY 2. REMOVE BATTERY 3. REMOVE WINDSHIELD WIPER LINK ASSY (See page 666) 4. REMOVE FRONT PANEL ASSY (See page 2610) 5. REMOVE CYLINDER HEAD
More information1990 SUSPENSION Front ES250, LS400
SUSPENSION - FRONT Article Text 1990 Lexus LS 400 For Lextreme Copyright 1998 Mitchell Repair Information Company, LLC Thursday, January 29, 2004 04:56PM ARTICLE BEGINNING 1990 SUSPENSION Front ES250,
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More informationEngine Removal and Installation
Page 1 of 5 Home Account Contact ALLDATA Log Out Help TINO TORRES Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Chrysler Sebring Sedan V6-2.7L VIN R Conversion Calculator Vehicle
More informationCOMPONENT LOCATOR > DISASSEMBLED VIEWS
Page 1 of 45 2006 Pontiac Grand Prix 3.8L Eng Base Service Manual: ENGINE MECHANICAL - 3.8L COMPONENT LOCATOR > DISASSEMBLED VIEWS Fig 1: Engine Block Component Views Callout Component Name 100 Engine
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION Removal 1. Center steering wheel. Disconnect negative battery cable. Remove steering coupling shield (if equipped). Disconnect steering shaft at flexible coupling or pot joint. Note
More informationALLDATA Online Jaguar Vanden Plas L6-3980cc 4.0L DOHC - Service and Rep...
Page 1 of 7 RENEW Jack up the front of the vehicle. Fit camber tie-down bars (Service Tool JD 133) to the road spring pans. NOTE: If, for any reason, the front crossmember is being stripped down, Service
More informationIntake Manifold Replacement
ALLDATA Online - 2001 Cadillac DeVille V8-4.6L VIN 9 - Intake Manifold Replacement Page 1 of 15 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's
More informationALLDATA Online Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K - Steeri... Steering Column
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2002 Dodge Truck RAM 1500 Truck 2WD V6-3.7L VIN K Conversion Calculator
More informationMODEL: 310A and 3108 Tractor, Loader and Backhoe Volume 1 of 2
John Deere MODEL: 310A and 3108 Tractor, Loader and Backhoe Volume 1 of 2 THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS
More informationFRONT DRIVE SHAFT COMPONENTS DS 1 DRIVE SHAFT FRONT DRIVE SHAFT FRONT DRIVE SHAFT HOLE SNAP RING. w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR
FRONT DRIVE SHAFT DRIVE LINE SHAFT COMPONENTS 1 FRONT DRIVE SHAFT HOLE SNAP RING 23 (235, 17) FRONT DRIVE SHAFT ASSEMBLY RH w/o ABS: AUTOMATIC TRANSMISSION CASE PROTECTOR FRONT DRIVE SHAFT ASSEMBLY LH
More informationFront Grille Replacement
Document ID: 4298678 Page 1 of 1 2017 Cadillac XT5 XT5 Service Manual Europe, Korea, N America, Other IO 9325297 Document ID: 4298678 Front Grille Replacement Front Grille Replacement Preliminary Front
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More informationLB LB LLY LLY 1000
6 November 2006 GMC/Chevy Allison Performance Transmission 1 BD PERFORMANCE TRANSMISSION Allison Installation Instructions 2WD Transmissions 4WD Transmissions 1064702 2000-2003 LB7 1000 1064704 2000-2003
More informationREMOVAL. 10. REMOVE FRONT SUSPENSION MEMBER BRACE Remove the 8 bolts and brace.
EM64 ENGINE MECHANICAL (2JZGE) EM1S801 REMOVAL 1. REMOVE ENGINE UNDER COVER 2. DRAIN ENGINE COOLANT 3. DRAIN ENGINE OIL 4. REMOVE ENGINE COVER Remove the 4 nuts and engine cover. 5. REMOVE AIR CLEANER
More information1998 Ford EXPEDITION. Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS. Transmission
1998 Ford EXPEDITION Submodel: Engine Type: V8 Liters: 5.4 Fuel Delivery: FI Fuel: GAS SECTION 307-01C: Automatic Transmission 4R100 1998 Expedition/Navigator Workshop Manual REMOVAL Procedure revision
More informationADJUSTMENTS Mazda MX-3. Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. VALVE CLEARANCE ADJUSTMENT
Fig. 1: Identifying Engine Code & Number Courtesy of MAZDA MOTORS CORP. ADJUSTMENTS VALVE CLEARANCE ADJUSTMENT 1. No valve clearance adjustment is required, as hydraulic valve lash adjusters are used.
More informationPRECAUTIONS ENGINE REPAIR
3234_U01.qxd 9/23/03 3:44 PM Page 13 BLAZER XTREME TRAILBLAZER BRAVADA ENVOY JIMMY 1-13 PRECAUTIONS Before servicing any vehicle, please be sure to read all of the following precautions, which deal with
More informationThis information covers the proper procedure for replacing the Volvo D16F engine in a VT or VNL chassis.
Volvo Trucks North America Greensboro, NC USA Engine, Replacement DService Bulletin Trucks Date Group No. Page 10.2007 210 139 1(47) Engine, Replacement Volvo D16F VNL, VT W2005773 This information covers
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
More informationSensor A/C Ambient Temperature 1951
SECTION 412-04: Control Components REMOVAL AND INSTALLATION Sensor A/C Ambient Temperature Removal 1. Remove the radiator upper sight shield. 2. Disconnect the wire harness connector. 3. Remove the A/C
More informationMODEL: 400 Hydrostatic Tractor
John Deere MODEL: 400 Hydrostatic Tractor THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF JOHN DEERE OR IT'S SUCCESSORS. JOHN DEERE AND IT'S SUCCESSORS ARE NOT RESPONSIBLE FOR THE
More information2004 Explorer/Mountaineer Workshop Manual
Page 1 of 6 SECTION 204-00: Suspension System 2004 Explorer/Mountaineer Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 08/05/2005 Wheel Bearing, Hub, Knuckle, Upper Arm and Lower Arm
More informationDISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,
More informationRemoving/installing final drive
1(16) Removing/installing final drive Special tools: 998 5972, 999 5561, 999 5652, 999 5659, 999 5660 Removing Note! Position the rear lifting arms on the arrows on the sills. This is so the support arm
More information3651 N Highway 89 Chino Valley, AZ (928)
3651 N Highway 89 Chino Valley, AZ 86323 (928) 636-7080 www.p-a-g.net CHEVY/GMC 1500 P/U GAS ENG. NEW BODY STYLE (INCLUDING AUTOMATIC TRANS W/ ELECTRONIC 4WD) 3 BODY LIFT KIT INSTALLATION INSTRUCTIONS
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More informationIntake Manifold Replacement
Page 1 of 13 Your Current Vehicle: 2008 Cadillac STS Intake Manifold Replacement Intake Manifold Replacement Removal Procedure 1. Turn the ignition OFF. 2. Remove the fuel injector sight shield. Refer
More informationThe steering column is of a modular construction and features easy to service electrical switches.
file://c:\tso\tsocache\vdtom_5368\svk~us~en~file=svkb4a01.htm~gen~ref.htm Page 1 of 3 Section 11-04A: Steering Column, Ranger DESCRIPTION AND OPERATION 1997 Ranger Workshop Manual Steering Column NOTE:
More informationTransmission, removing and
Page 1 of 20 34-18 Transmission, removing and installing Removing Special tools and equipment 3282 transmission support 3282/10 adjustment plate 3337 ring spanner 7-piece set VAG1383A engine/transmission
More informationMODEL NO & UP
FORM NO. 97 50xi GARDEN TRACTOR MODEL NO. 7570 990000 & UP SET UP INSTRUCTIONS Loose Parts Use the chart below to identify parts for assembly. DESCRIPTION QTY. USE Rear Wheel Wheel Bolt R.H. Wheel Spindle
More information