MEYER MATE 9.0 CU FT. SPREADER

Transcription

1 MEYER MATE 9.0 CU FT. SPREADER General Specifications Overall Height: 41.25" Overall Width: 49.5" Overall Depth: 32" Weight Empty: 140 lbs. Spreading Width: Minimum 3 Maximum 30 Spreading Material: Dry No. 1 rock salt Calcium chloride Sand Grass seed / fertilizer Hopper Material: Capacity: Cover: Linear Low-Density Polyethylene (LLDPE) 9.0 Cubic Feet (sand capacity 900 lbs.) LLDPE, with irregular (half circle opening) Motor Specifications Horsepower:.166 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction with shaft seal. Gear drive, 3:1 ratio. Spinner Drive Spinner Electrical Control Spinner Bank Direct from keyed-motor shaft. 14" diameter, 0.5" thick. One piece polymer with 4 fins. Built-in flow control auger and agitator. Hub agitator bolted to spinner. #10 gauge wiring from battery to motor. 2 conductor 14 AWG wire from vibrator. Quick connector at motor and vibrator. Speed control, viable in cab with Blast Feature High-density polyethylene spinner band, 0.19 wall.

2 MEYER MINI JR. SPREADER General Specifications Overall Height: 40" Overall Width: 28" Overall Depth: 29" Weight Empty: 120 lbs. Spreading Width: Minimum 3 Maximum 30 Spreading Material: Dry No. 1 rock salt Calcium chloride pellets or urea Pellets not recommended. Hopper Material: Capacity: Cover: Thermoplastic (steel mounting frame) 5.75 Cubic Feet (rock salt capacity 400 lbs.) Thermoplastic with two hold down latches. Motor Specifications Horsepower: 1/8 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction with shaft seal. Direct Drive. Spinner Drive Direct from keyed-motor shaft. Spinner 9" diameter #12 gauge (.1046) Fins welded to spinner 1/8" x 1", 2-1/2" long. Built-in flow control auger and agitator. Hub agitator bolted to spinner plate. Electrical Control Spinner Bank #10 gauge wiring from battery to motor. Quick connector at motor. Speed control, variable in cab with Blast Feature Black Fade Resistant High Density Polyethylene.

3 MEYER BLASTER CU FT. SPREADER General Specifications Overall Height: 35.50" Overall Width: 49" Overall Depth: 30" Weight Empty: 120 lbs. Spreading Width: Minimum 3 Maximum 40 Spreading Material: Dry No. 1 rock salt Hopper Material: Capacity: Cover: Linear Low-Density Polyethylene (LLDPE) 5.75 Cubic Feet (sand capacity 350 lbs.) LLDPE, with rectangular opening. Thermoplastic with two hold down latches. Motor Specifications Horsepower:.5 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction (Explosion Proof) 650 RPM Spinner Drive Spinner Electrical Control Spinner Bank Options Direct from keyed-motor shaft. 9" diameter,.06" thick. One piece stainless steel with 4 fins. Built-in flow control auger and agitator. Hub agitator bolted to spinner. #10 gauge wiring from battery to motor. Quick connector at motor. Speed control, viable in cab with with Blast Feature Low-density polyethylene spinner band, 3/16 wall. Vibrator Flow Control Hopper Screen

4 MEYER BLASTER 350S 5.75 CU FT. SPREADER General Specifications Overall Height: 35.50" Overall Width: 49" Overall Depth: 30" Weight Empty: 130 lbs. Spreading Width: Minimum 3 Maximum 40 Spreading Material: Dry No. 1 rock salt Dry Sand Hopper Material: Capacity: Cover: Linear Low-Density Polyethylene (LLDPE) 5.75 Cubic Feet (sand capacity 350 lbs.) LLDPE, with rectangular opening. Thermoplastic with two hold down latches. Motor Specifications Horsepower:.5 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction (Explosion Proof) 650 RPM Spinner Drive Spinner Electrical Control Spinner Bank Options Direct from keyed-motor shaft. 9" diameter,.06" thick. One piece stainless steel with 4 fins. Built-in flow control auger and agitator. Hub agitator bolted to spinner. #10 gauge wiring from battery to motor. 2 conductor 14 AWG wire from vibrator. Quick connector at motor and vibrator. Speed control, viable in cab with with Blast Feature Low-density polyethylene spinner band, 3/16 wall. Flow Control Hopper Screen

5 MEYER BLASTER CU FT. SPREADER General Specifications Overall Height: 44.50" Overall Width: 53.60" Overall Depth: 25" Weight Empty: 165 lbs. Spreading Width: Minimum 3 Maximum 40 Spreading Material: Dry No. 1 rock salt Hopper Material: Capacity: Cover: Linear Low-Density Polyethylene (LLDPE) Cubic Feet (sand capacity 750 lbs.) LLDPE, with rectangular opening. Thermoplastic with two hold down latches. Motor Specifications Horsepower:.5 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction (Explosion Proof) 650 RPM Spinner Drive Spinner Electrical Control Spinner Bank Options Direct from keyed-motor shaft. 9" diameter,.06" thick. One piece stainless steel with 4 fins. Built-in flow control auger and agitator. Hub agitator bolted to spinner. #10 gauge wiring from battery to motor. Quick connector at motor. Speed control, viable in cab with with Blast Feature Low-density polyethylene spinner band, 3/16 wall. Vibrator Flow Control Hopper Screen

6 MEYER BLASTER 750R CU FT. SPREADER General Specifications Overall Height: 44.50" Overall Width: 53.60" Overall Depth: 25" Weight Empty: 165 lbs. Spreading Width: Minimum 3 Maximum 40 Spreading Material: Dry No. 1 rock salt Hopper Material: Capacity: Cover: Linear Low-Density Polyethylene (LLDPE) Cubic Feet (sand capacity 750 lbs.) LLDPE, with rectangular opening. Thermoplastic with two hold down latches. Motor Specifications Horsepower:.5 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction (Explosion Proof) 650 RPM Spinner Drive Spinner Electrical Control Spinner Bank Options Direct from keyed-motor shaft. 9" diameter,.06" thick. One piece stainless steel with 4 fins. Built-in flow control auger and agitator. Hub agitator bolted to spinner. #10 gauge wiring from battery to motor. Quick connector at motor. Speed control, viable in cab with with Blast Feature Low-density polyethylene spinner band, 3/16 wall. Vibrator Flow Control Hopper Screen

7 MEYER BLASTER 750S CU FT. SPREADER General Specifications Overall Height: 44.50" Overall Width: 53.60" Overall Depth: 25" Weight Empty: 175 lbs. Spreading Width: Minimum 3 Maximum 40 Spreading Material: Dry No. 1 rock salt Dry Sand Hopper Material: Capacity: Cover: Linear Low-Density Polyethylene (LLDPE) Cubic Feet (sand capacity 750 lbs.) LLDPE, with rectangular opening. Thermoplastic with two hold down latches. Motor Specifications Horsepower:.5 Voltage: 12 volts D.C. Type: Permanent Magnet Sealed construction (Explosion Proof) 650 RPM Spinner Drive Spinner Electrical Control Spinner Bank Options Direct from keyed-motor shaft. 9" diameter,.06" thick. One piece stainless steel with 4 fins. Built-in flow control auger and agitator. Hub agitator bolted to spinner. #10 gauge wiring from battery to motor. 2 conductor 14 AWG wire from vibrator. Quick connector at motor and vibrator. Speed control, viable in cab with with Blast Feature Low-density polyethylene spinner band, 3/16 wall. Vibrator Flow Control Hopper Screen

8 MEYER 1.8 CUBIC YARD INSERT HOPPER SPREADER HOPPER 1. Type Mechanical Drive Insert V Box Hopper Spreader 2. Length (overall) 102" (inside) 84" 3. Top Width 54" 4. Capacity 1.8 Cubic Yards 5. Height 34" 6. Side Slope 45 Degrees 7. Material: Side, Longitudinales Hopper Ends Single piece construction, 12 Gauge Carbon Steel, double formed at top for added strength 14 Gauge Carbon Steel 8. Center Lift Hook Lift point at center of gravity 9. Gate Opening 7-3/4" x 4" 10. Feed Gate 7 Gauge Steel 11. Body Jacks 12 Gauge Steel (2 per side) 12. Floor 10 Gauge Steel CONVEYER 13. Overall Width 16" 14. Chain Shields Bolt on 15. Conveyor Chains Self Cleaning Pintle Type 16. Pitch 2-5/16" 17. Crossbar ¼ x 1 Rectangular Bar 18. Bar Spacing 6-5/16" Center to Center

9 PAGE 2 OF 3 MEYER 1.8 YARD INSERT HOPPER SPREADER 19. Tensile Strength 12,500 lbs. per Strand 20. Pin 5/16" Hardened Pin 21. Conveyor Drive Ratio 20:1 Gearbox 22. Worm Gear Hardened and Ground 23. Bull Gear Drive Gear Bronze Alloy 24. Chain Take Up (2) Adjustable ½ Cadmium Plated Bolts with 3" adjustments. 25. Drive Sprocket 6 Tooth Forged Steel keyed to Drive Shaft 26. Drive Shaft 1-1/4" Cold Finished Shaft 27. Idler Sprocket 6 Tooth Forged Steel (1) Welded (1) Floats 28. Idler Shaft 1-1/4" Cold Finished Shaft 29. Idler Bearings Relube Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing 30. Drive Shaft Bearings Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing SPINNER ASSEMBLY 31. Disc 13" Diameter / 10 Gauge Steel 32. Chute 12 Gauge Steel 33. External Baffles (3) Overlapping adjustable / 10 Gauge Steel Fixed Baffle to protect truck 34. Flite 6 Molded in 35. Bearing (2) 1" Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing 36. Hub Bolted to Spinner Shaft and molded to Spinner Disc 37. Spreading Width 4 to 30 Feet

10 PAGE 3 OF 3 MEYER 1.8 YARD INSERT HOPPER SPREADER ENGINE 38. Horsepower 10-1/2 H.P. Vertical Shaft Tecumseh 39. Start Electric Start 40. Control In Cab Start, Electric Throttle Controls 41. Battery Box and Hold Down Cables ONLY DRIVE 42. First Reduction B Section V-Belt and Pulleys 43. Clutch Electric Rated at 90Foot Pounds 44. Second Reduction 41 Roller Chain and Sprockets for Spinner Drive 45. Inverted Vee 10 Gauge Formed Steel 46. Screens 3/8" Rods Forming 2-1/2" Openings Sections hinged on one side OPTIONAL EQUIPMENT 47. Chain Hold Down 4 Reinforced nylon straps with ratchet and installation hardware. 48. Side Extension 14 Gauge Formed Steel 6" High Adds ½ Cubic Yard 49. Spinner Extension 6" Spinner Extension (For Stake and Dump trucks) Lowers Spinner to the proper height for spreading material. NOTE: SHOULD BE ORDERED WITH SPREADER 50. Prewetting System Powered by an electric 2.8 GPM 12V DC pump with cab mounted console which includes an ON/OFF switch, variable speed control and low pressure light and alarm. The system comes equipped with a low pressure sensor, weather proof polyurethane enclosure, two nozzle assembly, two 15 gallon polyurethane reservoirs, miscellaneous hardware and

11 MEYER 2.0 CUBIC YARD INSERT HOPPER SPREADER instruction manual. HOPPER 1. Type Mechanical Drive Insert V Box Hopper Spreader 2. Length (overall) 116" (inside) 96" 3. Top Width 54" 4. Capacity 1.8 Cubic Yards 5. Height 34" 6. Side Slope 45 Degrees 7. Material: Side, Longitudinales Hopper Ends Single piece construction, 12 Gauge Carbon Steel, double formed at top for added strength 14 Gauge Carbon Steel 8. Center Lift Hook Lift point at center of gravity 9. Gate Opening 7-3/4" x 4" 10. Feed Gate 7 Gauge Steel 11. Body Jacks 12 Gauge Steel (2 per side) 12. Floor 10 Gauge Steel CONVEYER 13. Overall Width 16" 14. Chain Shields Bolt on 15. Conveyor Chains Self Cleaning Pintle Type 16. Pitch 2-5/16" 17. Crossbar ¼ x 1 Rectangular Bar

12 18. Bar Spacing 6-5/16" Center to Center DATA SPECIFICATION SHEET PAGE 2 OF 3 MEYER 2.0 YARD INSERT HOPPER SPREADER 19. Tensile Strength 12,500 lbs. per Strand 20. Pin 5/16" Hardened Pin 21. Conveyor Drive Ratio 20:1 Gearbox 22. Worm Gear Hardened and Ground 23. Bull Gear Drive Gear Bronze Alloy 24. Chain Take Up (2) Adjustable ½ Cadmium Plated Bolts with 3" adjustments. 25. Drive Sprocket 6 Tooth Forged Steel keyed to Drive Shaft 26. Drive Shaft 1-1/4" Cold Finished Shaft 27. Idler Sprocket 6 Tooth Forged Steel (1) Welded (1) Floats 28. Idler Shaft 1-1/4" Cold Finished Shaft 29. Idler Bearings Relube Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing 30. Drive Shaft Bearings Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing SPINNER ASSEMBLY 31. Disc 13" Diameter / 10 Gauge Steel 32. Chute 12 Gauge Steel 33. External Baffles (3) Overlapping adjustable / 10 Gauge Steel Fixed Baffle to protect truck 34. Flite 6 Molded in 35. Bearing (2) 1" Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing 36. Hub Bolted to Spinner Shaft and molded to Spinner Disc

13 37. Spreading Width 4 to 30 Feet DATA SPECIFICATION SHEET PAGE 3 OF 3 MEYER 2.0 YARD INSERT HOPPER SPREADER ENGINE 38. Horsepower 10-1/2 H.P. Vertical Shaft Tecumseh 39. Start Electric Start 40. Control In Cab Start, Electric Throttle Controls 41. Battery Box and Hold Down Cables ONLY DRIVE 42. First Reduction B Section V-Belt and Pulleys 43. Clutch Electric Rated at 90Foot Pounds 44. Second Reduction 41 Roller Chain and Sprockets for Spinner Drive 45. Inverted Vee 10 Gauge Formed Steel 46. Screens 3/8" Rods Forming 2-1/2" Openings Sections hinged on one side OPTIONAL EQUIPMENT 47. Chain Hold Down 4 Reinforced nylon straps with ratchet and installation hardware. 48. Side Extension 14 Gauge Formed Steel 6" High Adds ½ Cubic Yard 49. Spinner Extension 6" Spinner Extension (For Stake and Dump trucks) Lowers Spinner to the proper height for spreading material. NOTE: SHOULD BE ORDERED WITH SPREADER 50. Prewetting System Powered by an electric 2.8 GPM 12V DC pump with cab mounted console which includes an ON/OFF switch, variable speed control and low pressure light and alarm. The system comes equipped with a low pressure sensor, weather proof polyurethane enclosure, two nozzle assembly, two 15 gallon polyurethane reservoirs, miscellaneous hardware and instruction manual.

14 MEYER MEDIUM DUTY HOPPER SPREADER HOPPER 1. Type Mechanical Drive Insert V Box Hopper Spreader 2. Length (overall) 116", 128" OR 140" 3. Top Width 70" 4. Capacity 3.0, 4.0, OR 4.5 CUBIC YARDS 5. Height 40", OR 44" 6. Side Slope 45 Degrees 7. Material: Side, Longitudinales Hopper Ends Single piece construction, 12 Gauge Carbon Steel, double formed at top for added strength 12 Gauge Carbon Steel 8. Center Lift Hook Lift point at center of gravity 9. Gate Opening 9" x 7" 10. Feed Gate 7 Gauge Steel 11. Body Jacks 12 Gauge Steel (3 per side) 12. Floor 10 Gauge Steel CONVEYER 13. Overall Width 16" 14. Chain Shields Replaceable chain shields 15. Conveyor Chains Self Cleaning Pintle Type 16. Pitch 2-5/16" 17. Crossbar ¼ x 1" Rectangular Bar 18. Bar Spacing 4-5/8" Center to Center

15 PAGE 2 OF 3 MEYER MEDIUM DUTY HOPPER 19. Tensile Strength 12,500 lbs. per Strand 20. Pin 5/16" Hardened Pin 21. Conveyor Drive Ratio 20:1 Gearbox 22. Worm Gear Hardened and Ground 23. Bull Gear Drive Gear Bronze Alloy 24. Chain Take Up (2) Spring loaded S.S. bolts w/ 3" adjustments 25. Drive Sprocket 6 Tooth Forged Steel keyed to Drive Shaft 26. Drive Shaft 1-1/4" Cold Finished Shaft 27. Idler Sprocket 6 Tooth Forged Steel (1) Welded (1) Floats 28. Idler Shaft 1-1/4" Cold Finished Shaft 29. Idler Bearings Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing 30. Drive Shaft Bearings Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing SPINNER ASSEMBLY 31. Disc 13" Diameter / Poly 32. Chute 12 Gauge Steel 33. External Baffles (3) Overlapping adjustable / 10 Gauge Steel Fixed Baffle to protect truck 34. Flite (6) Molded Poly 35. Bearing (2) 1" Precision Grade Self-Aligning Ball Type Sealed Re-lubricatable Bearing 36. Hub Bolted to Spinner Shaft and Molded to Spinner Disc 37. Spreading Width 4 to 30 Feet

16 PAGE 3 OF 3 MEYER MEDIUM DUTY HOPPER ENGINE 38. Horsepower 101/2 H.P. Vertical Shaft Tecumseh 39. Start Electric Start 40. Control In Cab Start, Electric Throttle Controls 41. Battery Box and Hold Down Cables ONLY DRIVE 42. First Reduction B Section V-Belt and Pulleys 43. Clutch Electric Rated at 90 Foot Pounds 44. Second Reduction 41 Roller Chain and Sprockets for Spinner Drive 45. Inverted Vee 10 Gauge Formed Steel 46. Screens 5/16 Rods Forming 2-1/2 Openings (2) Sections hinged on one side OPTIONAL EQUIPMENT 47. Chain Hold Down Kit 4 Reinforced nylon straps with ratchet and installation hardware. 48. Prewetting System Powered by an electric 2.8 GPM 12V DC pump with cab mounted console which includes an ON/OFF switch, variable speed control and low pressure light and alarm. The system comes equipped with a low pressure sensor, weather proof polyurethane enclosure, two nozzle assembly, two 30 gallon polyurethane reservoirs, miscellaneous hardware and instruction manual.

17 MEYER RTG DIRECT DRIVE 1. Type Replaceable Tailgate 2. Width 84 inches 3. Trough 7 Gauge (3/16") 4. End Plates ¼ 5. Discharge Opening 5" x 6-1/2" rectangular 6. Auger Standard 6" straight flite continuous auger; auger pipe 2-7/8" O.D.; Fliting 3/8" thick 7. Bearings Self-aligning, sealed, dust proof, with grease fittings, 1-1/4" diameter 8. Chain and Gear Drive #60 Single strand straight riveted with ¾ pitch 9. Chain Cover Hinged for easy access; no tools required 10. Spinner Horizontal adjustments 11. Spinner Material 18" Polyurethane disc 6 formed 3/16" spinner with fins for low trajectory 12. Spreading Pattern Spreads left to center or center to right 13. Spinner Motor Orbital type 14. Stabilizer Bar Keeps spinner parallel to road surface at all dump angles 15. Pump 16 / 19 GPM (@ 1000/1200 RPM) with thru shaft, gear type 16. Auger Motor Orbital type, protected from external damage by configuration of trough 17. Oil Reservoir (option) 7 Gallon capacity 18. Filter (option) 10 Micron, replaceable element

18 PAGE 2 OF 2 MEYER RTG DIRECT DRIVE 19. Control (option) Dual flow control valve, pressure compensated, separate controls 20. Control Mounting In cab 21. Clean Out Bottom opening One man operation; no parts to detach. 22. Latch 5/8" diameter 23. Couplers ½, and ¾ Quick disconnect with dust covers 24. Anti-flow plate 10 Gauge hot rolled steel 16" long 25. Color Trough, Meyer high visibility yellow spinner and attaching parts - black 26. Options Centerline chute

19 MEYER UTG DIRECT DRIVE 1. Type Under Tailgate 2. Width 88 inches or 96 inches 3. Trough 7 Gauge (3/16") 4. End Plates ¼ 5. Discharge Opening 5" x 7" rectangular 6. Cover 7 Gauge two position; spreading and dump 7. Auger Standard 6" straight, and reverse flite auger; auger pipe 2-7/8" O.D.; Fliting 3/8" thick 8. Bearing Self-aligning, sealed, dust proof, with grease fittings, 1-1/4" diameter 9. Direct Drive Auger Hydraulic Motor mounts directly into auger pipe by non-corrosive sleeve and a 42" grade 5 bolt 10. Spinner Horizontal adjustments 11. Spinner Material 18" Polyurethane disc 6 formed in spinner with low trajectory fins 12. Spreading Pattern Spreads left to center or center to right 13. Spinner Motor Orbital type 14. Stabilizer Bar Keeps spinner parallel to road surface at all dump angles 15. Pump (option) 16 / 19 GPM (@ 1000 RPM/1200) with thru shaft, gear type 16. Auger Motor Orbital type, protected from external damage by configuration of trough 17. Oil Reservoir (option) 7 Gallon capacity 18. Filter (option) 10 Micron, replaceable element

20 PAGE 2 OF 2 MEYER UTG DIRECT DRIVE 19. Control (option) Dual flow control valve, pressure compensated, separate controls 20. Control Mounting In cab 21. Clean Out One piece, hinged bottom One man operation; no parts to detach. 22. Latch 5/8" diameter 23. Couplers (option) ½, and ¾ Quick disconnect with dust covers 24. Anti-flow plate 10 Gauge hot rolled steel 20" long 25. Color Trough, Meyer high visibility yellow spinner and attaching parts - black 26. Options Centerline chute