1ASD-6CDSS-6P-1D-2S-LM "Salt Special" sander, dual spinner, w/unidirectional reversible auger, includes extra salt shields (Per Ea)

Transcription

1 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model FALLS 1ASD-6 Stainless Steel Under tailgate type, 6" dia (carbon steel) 6" pitch, single auger, direct hydraulic drive, LH Discharge w/poly self-leveling spinner assembly, Dual over-center locks on hopper cleanout door, mtg brackets and mtg tabs for hopper, In Stainlesss Steel 24 months from In-Service date TOTAL PRICE: SEE TABLE BELOW ASD-6CDSS-6P-1D-1S-SM complete sander (Per Ea) 3, or More in Single Order (Per Ea) 3, ASD-6CDSS-6P-1D-2S-SM sander, dual spinner, w/uni-directional 4, reversible auger (Per Ea) 10 or More in Single Order (Per Ea) 4, ASD-6CDSS-6P-1D-1S-LM "Salt Special" complete sander, includes 4, extra salt shield (Per Ea) 10 or More in Single Order (Per Ea) 4, ASD-6CDSS-6P-1D-2S-LM "Salt Special" sander, dual spinner, w/unidirectional reversible auger, includes extra salt shields (Per Ea) 5, or More in Single Order (Per Ea) 5, Installation of Install sander w/dual manifold at RH & LH rear corners, with standard couplers Install sander w/dual manifold at RH & LH rear corners, with dripless couplers 1, Install sander dual spinner w/uni-directional reversible auger, w/dual manifolds at RH & LH rear corners, with std couplers 1, Install sander dual spinner w/uni-directional reversible auger, w/dual manifolds at RH & LH rear corners, w/dripless couplers 1, OTHER OPTIONS Exterior (removable) sander/tailgate spill plates, Stainless Steel Exterior (bolt-on) sander/tailgate spill plates, Stainless Steel Prep & Adapt for existing body or for ship-out Stainless steel (optional) salt shield TMTE adjustable roller sander stand Cost per loaded mile for delivery of sander

2 FAX NO

3 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model FALLS 1ASD-9 Stainless Steel Under tailgate type, 9" dia (carbon steel) 6" pitch, single auger, direct hydraulic drive, LH Discharge w/poly self-leveling spinner assembly, RH berm chute assembly, Dual overcenter locks on hopper cleanout door, mtg brackets and mtg tab 24 months from In-Service date TOTAL PRICE: SEE TABLE BELOW ASD9SS-6P-1D-1S (6" pitch auger) complete sander (Per Ea) 4, or More in Single Order (Per Ea) 4, ASD9SS-6P-1D-2S (6" pitch auger) uni-directional reversible, w/dual spinners sander (Per Ea) 5, or More in Single Order (Per Ea) 4, ASD9SS-4P-1D-1S (4" pitch auger) complete sander (Per Ea) 4, or More in Single Order (Per Ea) 4, ASD9SS-4P-1D-2S (4" pitch auger) uni-directional reversible w/dual spinners sander (Per Ea) 5, or More in Single Order (Per Ea) 5, Installation of Install sander w/dual manifold at RH & LH rear corners, with standard couplers Install sander w/dual manifold at RH & LH rear corners, with dripless couplers 1, Install sander dual spinner w/uni-directional reversible auger, w/dual manifolds at RH & LH rear corners, with std couplers 1, Install sander dual spinner w/uni-directional reversible auger, w/dual manifolds at RH & LH rear corners, w/dripless couplers 1, OTHER OPTIONS Exterior (removable) sander/tailgate spill plates, Stainless Steel Exterior (bolt-on) sander/tailgate spill plates, Stainless Steel Prep & Adapt for existing body or for ship-out Stainless steel (optional) salt shield TMTE adjustable roller sander stand Cost per loaded mile for delivery of sander

4 FAX NO

5 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Swenson STCC Cross-Conveyor 14" wide hi-temp belt over chain, hinged 7 ga top cover, w/2 positive latches to allow material dump over. Dual 10" x 14" feed gates with gate jacks, 102" trough opening. 24" extension to help position matl outside of tire path. Mtg hdwe & stabilizer k 12 months from In-Service date TOTAL PRICE: 7, Installation of Install Cross Conveyer w/light Bar 1, Install Cross Conveyer w/light Bar & Reversing Valve 1, Install Cross Conveyor w/light bar & Dripless Couplers 1, Install Cross Conveyor w/light bar, Reversing Valve, & Dripless Couplers 1, OTHER OPTIONS Reversing valve for STCC (ship out) Self storage legs (ship out) 2, Swenson 4' MOTORIZED EXTENSION POWDER COATED BLACK (ship out) 4, FAX NO Cost per loaded mile for delivery of sander

6 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Swenson SADS-6 STAINLESS STEEL Under tailgate type, 6" dia single auger w/continuous flighting, to discharge at extreme left end. Discharges 6.0 lbs/revolution. Direct drive motors. 18" POLY spinner assembly w/stabilizer arm. 12 months from In-Service date TOTAL PRICE: 3, Installation of Install sander & manifold RH rear Install sander & dual manifold RH & LH rear 1, Install sander & manifold RH rear with dripless coupler 1, Install sander & dual manifold RH & LH rear with dripless couplers 1, OTHER OPTIONS Exterior (removable) sander/tailgate spill plates, Stainless Steel Exterior (bolt-on) sander/tailgate spill plates, Stainless Steel Prep & Adapt for existing body or for ship-out Stainless steel (optional) salt shield TMTE adjustable roller sander stand FAX NO Cost per loaded mile for delivery of sander

7 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Swenson SBDS-9 STAINLESS STEEL Under tailgate type, 9" dia single auger w/continuous flighting, to discharge at extreme left or right end. Includes berm chute for RH or LH. Discharges 21.0 lbs/revolution. Direct drive motors. 18" POLY LH spinner assembly w/stabilizer arm. 12 months from In-Service date TOTAL PRICE: 4, Installation of Install sander & manifold RH rear Install sander & dual manifold RH & LH rear 1, Install sander & manifold RH rear with dripless coupler 1, Install sander & dual manifold RH & LH rear with dripless couplers 1, OTHER OPTIONS Exterior (removable) sander/tailgate spill plates, Stainless Steel Exterior (bolt-on) sander/tailgate spill plates, Stainless Steel Prep & Adapt for existing body or for ship-out Stainless steel (optional) salt shield TMTE adjustable roller sander stand FAX NO Cost per loaded mile for delivery of sander

8 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Swenson Stainless Steel EV-100 Series EV-100 series: hydraulic drive spreader manufactured of 10 gauge carbon steel sides/ends, 82 wide hopper ends, 7gauge slotted longitudinals for easy gearbox/drive shaft removal, 45 side slope, bolt in 6 wide flange H beam, Drop-N-loc top screens, self cleaning pintle style conveyor chain, rear chain wiper, 12 adjustable in height spinner extension, lower spinner assembly with bottom mounted motor, 7 ga 20 carbon steel spinner assembly, & 50:1 ratio gear box. 8 tooth sprockets, w/1-1/2 drive & 1-1/4"idler shafts, w/spring loaded chain take-up. 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW Optional Features included in the sanders listed below Front bearing grease extension to rear manifold; Chain Oiler - Gravity type - Stainless Steel, 1 gal, with Cap; Swing up Spinner; Winch for Swing-up Spinner; Inverted Vee; Low temp Belt over Chain Swenson SS EV Complete 13, Swenson SS EV Complete 14, Swenson SS EV Complete 14, Swenson SS EV Complete 15, Swenson SS EV Complete 15, Swenson SS EV Complete 16, Swenson SS EV Complete 16, Swenson SS EV Complete 17, Swenson SS EV Complete 13, Swenson SS EV Complete 14, Swenson SS EV Complete 14, Swenson SS EV Complete 15, Swenson SS EV Complete 15, Swenson SS EV Complete 16, Swenson SS EV Complete 16, Swenson SS EV Complete 17, Swenson SS EV Complete 14, Swenson SS EV Complete 14, Swenson SS EV Complete 14, Swenson SS EV Complete 15, Swenson SS EV Complete 15, Swenson SS EV Complete 16, Swenson SS EV Complete 17, Swenson SS EV Complete 17,627.00

9 Line Item P/N Option Description PRICE Swenson SS 1-90 GAL V-BOX TANK OPTIONS 1, Swenson SS 2-90 GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 2, Swenson SS GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 2, Swenson 1 V-BOX TANK SYSTEM FACTORY INSTALLED Swenson 2 V-BOX TANK SYSTEM FACTORY INSTALLED Swenson PPS II system - G2 COMPLETE , Swenson G2 controls, cables, spinner chute , Swenson G2 metering wheel , Swenson Aviation Spinner Assembly 4, Swenson Light Bar with Stop, Turn, Tail Lights , Swenson Light Bar with Stop, Turn, Tail and Flashing Lights , Swenson Light Bar with Stop, Turn, Tail and Strobe Lights , Swenson Light Bar with Stop, Turn, Tail and Back Up Lights , Swenson 4" Pedestal Mount Work Light Installation of Install V-Box (as Slide-In) into Dump Body 1, Install V-Box as rigid frame mount on chassis 1, Install V-Box on A-FRAME for Hooklift application NOTE: See 1.0 Body Options for A-Frame pricing 1, FAX NO Cost per loaded mile for delivery of sander

10 PRICE SCHEDULE Make and Model TO PROVIDE Swenson Stainless Steel EVA-100 Series EVA-100 series: SINGLE AUGER hydraulic drive spreader manufactured of 10 gauge carbon steel sides/ends, 84 wide hopper ends, 7gauge slotted longitudinals for easy gearbox/drive shaft removal, 45 side slope, bolt in 6 wide flange H beam, Drop-N-loc top screens, self, 7" diameter hard surfaced auger with 3 pitch lengths for even unloading front to back, Direct drive 18 HP hydraulic motor, 12" adjustable in height spinner extension, 1 internal baffle, 4 baffle (3 adjustable, front fixed) lower spinner assembly with bottom mounted motor. Rear grease extension, Inverted vee, Powder coated Omaha Orange, or Stainless Steel 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW Swenson EVA V-Box Complete 9, Swenson EVA V-Box Complete 10, Swenson EVA V-Box Complete 10, Swenson EVA V-Box Complete 11, Swenson EVA V-Box Complete 12, Swenson EVA V-Box Complete 9, Swenson EVA V-Box Complete 10, Swenson EVA V-Box Complete 10, Swenson EVA V-Box Complete 11, Swenson EVA V-Box Complete 12, Swenson EVA V-Box Complete 10, Swenson EVA V-Box Complete 10, Swenson EVA V-Box Complete 11, Swenson EVA V-Box Complete 11, Swenson EVA V-Box Complete 12, Swenson EVA STAINLESS STEEL V-Box Complete 14, Swenson EVA STAINLESS STEEL V-Box Complete 15, Swenson EVA STAINLESS STEEL V-Box Complete 16, Swenson EVA STAINLESS STEEL V-Box Complete 16, Swenson EVA STAINLESS STEEL V-Box Complete 17, Swenson EVA STAINLESS STEEL V-Box Complete 15, Swenson EVA STAINLESS STEEL V-Box Complete 15, Swenson EVA STAINLESS STEEL V-Box Complete 16, Swenson EVA STAINLESS STEEL V-Box Complete 17, Swenson EVA STAINLESS STEEL V-Box Complete 17, Swenson EVA STAINLESS STEEL V-Box Complete 18, Swenson EVA STAINLESS STEEL V-Box Complete 15, Swenson EVA STAINLESS STEEL V-Box Complete 15, Swenson EVA STAINLESS STEEL V-Box Complete 16, Swenson EVA STAINLESS STEEL V-Box Complete 17,393.00

11 Swenson EVA STAINLESS STEEL V-Box Complete 18, SWENSON UP CHARGE SINGLE AUGER TO DUAL AUGER 1, Line Item P/N Option Description PRICE Swenson SS 1-90 GAL V-BOX TANK OPTIONS 1, Swenson SS 2-90 GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 2, Swenson SS GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 2, Swenson 1 V-BOX TANK SYSTEM FACTORY INSTALLED Swenson 2 V-BOX TANK SYSTEM FACTORY INSTALLED Swenson PPS II system - G2 COMPLETE , Swenson G2 controls, cables, spinner chute , Swenson G2 metering wheel , Swenson Aviation Spinner Assembly 4, Swenson Light Bar with Stop, Turn, Tail Lights , Swenson Light Bar with Stop, Turn, Tail and Flashing Lights , Swenson Light Bar with Stop, Turn, Tail and Strobe Lights , Swenson Light Bar with Stop, Turn, Tail and Back Up Lights , Swenson 4" Pedestal Mount Work Light Installation of Install V-Box (as Slide-In) into Dump Body 1, Install V-Box as rigid frame mount on chassis 1, Install V-Box on A-FRAME for Hooklift application NOTE: See 1.0 Body Options for A-Frame pricing 1, FAX NO Cost per loaded mile for delivery of sander

12 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Swenson Stainless Steel EVDA Aviation Special EVDA-17-66, DUAL AUGER hydraulic drive spreader manufactured of 12 gauge STAINLESS steel sides/ends, 84 wide hopper ends, 7gauge slotted longitudinals for easy gearbox/drive shaft removal, 45 side slope, bolt in 6 wide flange H beam, DUAL 7" diameter hard surfaced auger with 3 pitch lengths for even unloading front to back, DUAL Direct drive 18 HP hydraulic motors, AVIATION SPINNER system, GAL Liquid TANKS W/STAINLESS STEEL MOUNTING HARDWARE 12 months from In-Service date TOTAL PRICE: 29, Installation of Install V-Box as rigid frame mount on chassis 1, FAX NO Cost per loaded mile for delivery of sander

13 PRICE SCHEDULE Make and Model TO PROVIDE Swenson Stainless Steel EV-150 Series EV-150 series: hydraulic drive spreader manufactured of 10 gauge carbon steel sides/ends, 82 wide hopper ends, 7gauge slotted longitudinals for easy gearbox/drive shaft removal, 45 side slope, bolt in 6 wide flange H beam, Drop-N-loc top screens, self cleaning pintle style conveyor chain, rear chain wiper, 12 adjustable in height spinner extension, lower spinner assembly with bottom mounted motor, 7 ga 20 carbon steel spinner assembly, & 50:1 ratio gear box. 8 tooth sprockets, w/2 drive & idler shafts, w/spring loaded chain take-up. 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW Swenson SS EV Installed 16, Swenson SS EV Installed 17, Swenson SS EV Installed 17, Swenson SS EV Installed 18, Swenson SS EV Installed 18, Swenson SS EV Installed 19, Swenson SS EV Installed 20, Swenson SS EV Installed 20, Swenson SS EV Installed 16, Swenson SS EV Installed 17, Swenson SS EV Installed 17, Swenson SS EV Installed 18, Swenson SS EV Installed 18, Swenson SS EV Installed 19, Swenson SS EV Installed 20, Swenson SS EV Installed 20, Swenson SS EV Installed 16, Swenson SS EV Installed 17, Swenson SS EV Installed 17, Swenson SS EV Installed 18, Swenson SS EV Installed 19, Swenson SS EV Installed 19, Swenson SS EV Installed 20, Swenson SS EV Installed 21, Optional Features included in the sanders listed above Front bearing grease extension to rear manifold; Chain Oiler - Gravity type - Stainless Steel, 1 gal, with Cap; Swing up Spinner; Winch for Swing-up Spinner; Inverted Vee; Low temp Belt over Chain. Line Item P/N Option Description PRICE

14 Swenson SS 1-90 GAL V-BOX TANK OPTIONS 1, Swenson SS 2-90 GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 2, Swenson SS GAL V-BOX TANK OPTIONS 1, Swenson SS GAL V-BOX TANK OPTIONS 2, Swenson 1 V-BOX TANK SYSTEM FACTORY INSTALLED Swenson 2 V-BOX TANK SYSTEM FACTORY INSTALLED Swenson PPS II system - G2 COMPLETE , Swenson G2 controls, cables, spinner chute , Swenson G2 metering wheel , Swenson Aviation Spinner Assembly 4, Swenson Light Bar with Stop, Turn, Tail Lights , Swenson Light Bar with Stop, Turn, Tail and Flashing Lights , Swenson Light Bar with Stop, Turn, Tail and Strobe Lights , Swenson Light Bar with Stop, Turn, Tail and Back Up Lights , Swenson 4" Pedestal Mount Work Light Installation of Install V-Box (as Slide-In) into Dump Body 1, Install V-Box as rigid frame mount on chassis 1, Install V-Box on A-FRAME for Hooklift application NOTE: See 1.0 Body Options for A-Frame pricing 1, FAX NO Cost per loaded mile for delivery of sander

15 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Heavy-duty 7-gauge cover/back plate and trough with 1/4" endgates. (Steel gauges remain the same for 304SS units.) Body is designed to fit below the tailgate of dump bodies with an outside width of 94" to 96". 7-guage, 3-point hinged bottom panel exposes the entire length of the auger for ease in clean out and service. Heavy-duty cam lock latches with lift handle to secure bottom panel when in operation. 6" diameter carbon steel auger with 3/8" thick bi-directional helicoid flighting welded to a heavy-duty 2-1/2" pipe. Direct drive hydraulic motor eliminates the maintenance of chain and sprocket drive or gear case drive. Quick disconnect mounting kit. (Mounting kit matches the steel type of the unit.) 304 stainless steel tailgate baffle kit is standard on stainless steel units. 18" polyurethane spinner disc with 6 formed radial fins to produce a uniform pattern from 4 to 40 feet in width. The carbon steel spinner assembly can be easily adjusted to vary spread pattern and is easily removed by pulling two pins and uncoupling two hydraulic hoses. Included is a curved adjustable steel spinner baffle to control material direction and a universal parallel arm. (Spinner frame and baffles match steel type of unit.) 304 stainless steel units are unpainted (non-304ss components are painted black). HI-WAY SA-6C STAINLESS STEEL Under Tailgate Spreader 12 months from In-Service date TOTAL PRICE: 4, Installation of Install sander & manifold RH rear Install sander & dual manifold RH & LH rear 1, Install sander & manifold RH rear with dripless coupler 1, Install sander & dual manifold RH & LH rear with dripless couplers 1, OTHER OPTIONS Exterior (removable) sander/tailgate spill plates, Stainless Steel Exterior (bolt-on) sander/tailgate spill plates, Stainless Steel Prep & Adapt for existing body or for ship-out Stainless steel (optional) salt shield TMTE adjustable roller sander stand FAX NO Cost per loaded mile for delivery of sander

16

17 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model Heavy-duty 7-gauge cover/back plate and trough with 1/4" endgates. (Steel gauges remain the same for 304SS units.) Body is designed to fit below the tailgate of dump bodies with an outside width of 94" to 96". 7-guage, 3-point hinged bottom panel exposes the entire length of the auger for ease in clean out and service. Heavy-duty cam lock latches with lift handle to secure bottom panel when in operation. 9" diameter carbon steel auger with 5/8" thick helicoid flighting welded to a heavy-duty 2-1/2" pipe. Unit is capable of discharging up to 3/4" aggregate for road shoulder berming. Direct drive hydraulic motor eliminates the maintenance of chain and sprocket drive or gear case drive. Quick disconnect mounting kit. (Mounting kit matches the steel type of the unit.) 304 stainless steel tailgate baffle kit is standard on stainless steel units. 18" polyurethane spinner disc with 6 formed radial fins to produce a uniform pattern from 4 to 40 feet in width. The carbon steel spinner assembly can be easily adjusted to vary spread pattern and is easily removed by pulling two pins and uncoupling two hydraulic hoses. Included is a curved adjustable steel spinner baffle to control material direction and a universal parallel arm. (Spinner frame and baffles match steel type of unit.) 304 stainless steel units are unpainted (non-304ss components are painted black). Dual purpose heavy-duty carbon steel material chute. This chute can be easily removed or installed without the use of tools for either right-hand berming applications or left-hand centerline windrowing. HI-WAY SA-9 STAINLESS STEEL Under Tailgate Spreader 12 months from In-Service date TOTAL PRICE: 5, Installation of Install sander & manifold RH rear Install sander & dual manifold RH & LH rear 1, Install sander & manifold RH rear with dripless coupler 1, Install sander & dual manifold RH & LH rear with dripless couplers 1, OTHER OPTIONS Exterior (removable) sander/tailgate spill plates, Stainless Steel Exterior (bolt-on) sander/tailgate spill plates, Stainless Steel Prep & Adapt for existing body or for ship-out Stainless steel (optional) salt shield TMTE adjustable roller sander stand Cost per loaded mile for delivery of sander

18 FAX NO

19 - Make and Model PRICE SCHEDULE 8.0 TO PROVIDE HI-WAY TGC-18 Fully welded 7-gauge trough, bottom and endgates. Both endgates adjust for controlled material flow and swing open for high-speed dumping. Body is designed to fit below the tailgate of dump bodies with an outside width of 94" to 96". 18" wide Hi-Temp (-10 F to 350 F) belt over chain conveyor (BOC). Heat & oil resistant belt screwed to 1/4" X 1" crossbars for positive discharge of materials. (Not recommended for abrasive materials.) NOTE: Hi-Temp belt is not rated for operation in a temperature range of less than -10 F. Conveyor is reversible for either right- or left-hand discharge. Quick disconnect mounting kit to enable quick removal and mounting of spreader without the use of tools. Prior to painting, all components are chemically cleaned. Upon completion of the cleaning process, all exposed hopper seams not welded are chemically sealed. All components are then double coated with a lead- and chrome-free plural-component epoxy primer. The hopper body is painted with two finish coats of Hi-Way yellow plural-component urethane paint and then oven-cured. Bolt-on components are painted Hi-Way black urethane, oven-cured & assembled. All units are topped with a black decal group. Note: For proper operation, hydraulic system requires GPM at 1500 PSI. reversible tailgate conveyor/spreader 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW HI-WAY TGC-18 reversible tailgate PAINTED STEEL conveyor/spreader complete 5, INTALLATION Install Cross Conveyer 1, Install Cross Conveyer & Reversing Valve 1, Install Cross Conveyor & Dripless Couplers 1, Install Cross Conveyor w/reversing Valve, & Dripless Couplers 1, OTHER OPTIONS Reversing valve FAX NO Cost per loaded mile for delivery of sander

20 PRICE SCHEDULE Make and Model TO PROVIDE HI-WAY Stainless Steel E2500 V-BOX SPREADER Standard 82" wide body is constructed of a 10-gauge hopper, stakes and longsills with a 7-gauge bolt-in replaceable conveyor bottom panel. (Stainless steel units are constructed of a 12-gauge hopper, stakes and longsills with a 10-gauge bolt-in replaceable conveyor bottom panel.) Equipped with 2 hydraulic motors. One motor is mounted to the gear case; the other motor provides power to the spinner disc. No other hydraulic components are included. (See hydraulics options - page 2.) 24" wide pintle-type chain conveyor with 1/4" X 1-1/2" crossbars. This conveyor is driven by a 50:1 reduction worm gear drive with a hitorque/low-speed hydraulic motor. Enclosed spinner hopper is height adjustable and has a hinged rear panel which allows material to be discharged without striking the spinner. Two internal spinner deflectors provide placement of material on to the spinner disc driven by a direct, top mounted hydraulic spinner motor. The 20" diameter spinner disc is provided with six bolt-on fins and four baffles designed for complete control of material application. The entire assembly shall swing-up to allow for bulk unloading, cleaning, or storage. Prior to painting, all components are chemically cleaned. Upon completion of the cleaning process, all exposed seams not welded are chemically sealed. All components are then double coated with a lead- and chrome-free plural-component epoxy primer. The hopper body is painted with two finish coats of Hi-Way yellow pluralcomponent urethane paint and then oven-cured. Bolt-on components are painted Hi-Way black urethane, oven-cured and assembled. 304 stainless steel units are unpainted (non-304 stainless steel components are painted black). All units are topped with a black decal group. Note: For proper operation, hydraulic system requires GPM at 1500 PSI. 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW HI-WAY STAINLESS STEEL V-BOX 9' E (4.7 cubic yard struck capacity) HI-WAY STAINLESS STEEL V-BOX 10' E (5.2 cubic yard HI-WAY STAINLESS STEEL V-BOX 11' E (5.8 cubic yard HI-WAY STAINLESS STEEL V-BOX 12' E (6.3 cubic yard HI-WAY STAINLESS STEEL V-BOX 13' E (6.9 cubic yard HI-WAY STAINLESS STEEL V-BOX 14' E (7.5 cubic yard HI-WAY STAINLESS STEEL V-BOX 15' E (8.0 cubic yard HI-WAY STAINLESS STEEL V-BOX 16' E (8.6 cubic yard , , , , , , , , Options included in the sanders listed above Front bearing grease extension to rear; Front Idler adjustment to the rear; Auto Oiler; Poly Spinner; & Swing up Spinner Assembly Line Item P/N Option Description PRICE HI-WAY E2020XT/E2500 6" integrated side extensions SS 9' HI-WAY E2020XT/E2500 6" integrated side extensions SS 10'

21 HI-WAY E2020XT/E2500 6" integrated side extensions SS 11' HI-WAY E2020XT/E2500 6" integrated side extensions SS 12' HI-WAY E2020XT/E2500 6" integrated side extensions SS 13' HI-WAY E2020XT/E2500 6" integrated side extensions SS 14' HI-WAY E2020XT/E2500 6" integrated side extensions SS 15' HI-WAY E2020XT/E2500 6" integrated side extensions SS 16' HI-WAY E2020XT/E " integrated side extensions SS 9' HI-WAY E2020XT/E " integrated side extensions SS 10' HI-WAY E2020XT/E " integrated side extensions SS 11' HI-WAY E2020XT/E " integrated side extensions SS 12' HI-WAY E2020XT/E " integrated side extensions SS 13' HI-WAY E2020XT/E " integrated side extensions SS 14' HI-WAY E2020XT/E " integrated side extensions SS 15' 1, HI-WAY E2020XT/E " integrated side extensions SS 16' 1, HI-WAY 2020XT/E2500 Inverted V SS 9' HI-WAY 2020XT/E2500 Inverted V SS 10' HI-WAY 2020XT/E2500 Inverted V SS 11' HI-WAY 2020XT/E2500 Inverted V SS 12' HI-WAY 2020XT/E2500 Inverted V SS 13' HI-WAY 2020XT/E2500 Inverted V SS 14' HI-WAY 2020XT/E2500 Inverted V SS 15' HI-WAY 2020XT/E2500 Inverted V SS 16' HI-WAY 2020XT/E2500 Hinged screens 9' 1, HI-WAY 2020XT/E2500 Hinged screens 10' 1, HI-WAY 2020XT/E2500 Hinged screens 11' 1, HI-WAY 2020XT/E2500 Hinged screens 12' 1, HI-WAY 2020XT/E2500 Hinged screens 13' 2, HI-WAY 2020XT/E2500 Hinged screens 14' 2, HI-WAY 2020XT/E2500 Hinged screens 15' 2, HI-WAY 2020XT/E2500 Hinged screens 16' 2, INTALLATION Install V-Box (as Slide-In) into Dump Body 1, Install V-Box as rigid frame mount on chassis 1, Install V-Box on A-FRAME for Hooklift application NOTE: See 1.0 Body Options for A-Frame pricing 1, FAX NO Cost per loaded mile for delivery of sander

22 PRICE SCHEDULE Make and Model TO PROVIDE HI-WAY Stainless Steel 2020XT V-BOX SPREADER Standard 82" wide "easy service" body is constructed of a 10- gauge hopper and stakes with 7-gauge longsills and bolt-in replaceable conveyor bottom panel. (Stainless steel units are constructed of a 12-gauge hopper and stakes with 10-gauge conveyor bottom panel and longsills.) Equipped with 2 hydraulic motors. One motor is mounted to the gear case; the other motor provides power to the spinner disc. No other hydraulic components are included. 24" wide roller-type chain conveyor with 3/8" X 1-1/2" crossbars. This conveyor is driven by a 6:1 reduction spur gear drive with a hi-torque/low-speed hydraulic motor (highest efficiency-98% for lower operational and maintenance cost). Fully enclosed spinner hopper with two internal deflectors and a 20" diameter hydraulically driven spinner disc with six bolt-on harden fins and four baffles designed for complete control of material application. Prior to painting, all components are chemically cleaned. Upon completion of the cleaning process, all exposed seams not welded are chemically sealed. All components are then double coated with a lead- and chrome-free plural-component epoxy primer. Bolt-on components are painted Hi-Way black urethane, oven-cured and assembled. 304 stainless steel units are unpainted (non-304 stainless steel components are painted black). All units are topped with a black decal group. Note: For proper operation, hydraulic system requires GPM at 1500 PSI for series system, and GPM at 1500 PSI for dual system. 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW HI-WAY STAINLESS STEEL V-BOX 9' 2020XT - (4.7 cubic yard struck capacity) HI-WAY STAINLESS STEEL V-BOX 10' 2020XT - (5.2 cubic yard HI-WAY STAINLESS STEEL V-BOX 11' 2020XT - (5.8 cubic yard HI-WAY STAINLESS STEEL V-BOX 12' 2020XT - (6.3 cubic yard HI-WAY STAINLESS STEEL V-BOX 13' 2020XT - (6.9 cubic yard HI-WAY STAINLESS STEEL V-BOX 14' 2020XT - (7.5 cubic yard HI-WAY STAINLESS STEEL V-BOX 15' 2020XT - (8.0 cubic yard HI-WAY STAINLESS STEEL V-BOX 16' 2020XT- (8.6 cubic yard , , , , , , , , Options included in the sanders listed above Front bearing grease extension to rear; Front Idler adjustment to the rear; Auto Oiler; Poly Spinner; & Swing up Spinner Assembly Line Item P/N Option Description PRICE HI-WAY E2020XT/E2500 6" integrated side extensions SS 9' HI-WAY E2020XT/E2500 6" integrated side extensions SS 10' HI-WAY E2020XT/E2500 6" integrated side extensions SS 11'

23 HI-WAY E2020XT/E2500 6" integrated side extensions SS 12' HI-WAY E2020XT/E2500 6" integrated side extensions SS 13' HI-WAY E2020XT/E2500 6" integrated side extensions SS 14' HI-WAY E2020XT/E2500 6" integrated side extensions SS 15' HI-WAY E2020XT/E2500 6" integrated side extensions SS 16' HI-WAY E2020XT/E " integrated side extensions SS 9' HI-WAY E2020XT/E " integrated side extensions SS 10' HI-WAY E2020XT/E " integrated side extensions SS 11' HI-WAY E2020XT/E " integrated side extensions SS 12' HI-WAY E2020XT/E " integrated side extensions SS 13' HI-WAY E2020XT/E " integrated side extensions SS 14' HI-WAY E2020XT/E " integrated side extensions SS 15' 1, HI-WAY E2020XT/E " integrated side extensions SS 16' 1, HI-WAY 2020XT/E2500 Inverted V SS 9' HI-WAY 2020XT/E2500 Inverted V SS 10' HI-WAY 2020XT/E2500 Inverted V SS 11' HI-WAY 2020XT/E2500 Inverted V SS 12' HI-WAY 2020XT/E2500 Inverted V SS 13' HI-WAY 2020XT/E2500 Inverted V SS 14' HI-WAY 2020XT/E2500 Inverted V SS 15' HI-WAY 2020XT/E2500 Inverted V SS 16' HI-WAY 2020XT/E2500 Hinged screens 9' 1, HI-WAY 2020XT/E2500 Hinged screens 10' 1, HI-WAY 2020XT/E2500 Hinged screens 11' 1, HI-WAY 2020XT/E2500 Hinged screens 12' 1, HI-WAY 2020XT/E2500 Hinged screens 13' 2, HI-WAY 2020XT/E2500 Hinged screens 14' 2, HI-WAY 2020XT/E2500 Hinged screens 15' 2, HI-WAY 2020XT/E2500 Hinged screens 16' 2, INTALLATION Install V-Box (as Slide-In) into Dump Body 1, Install V-Box as rigid frame mount on chassis 1, Install V-Box on A-FRAME for Hooklift application NOTE: See 1.0 Body Options for A-Frame pricing 1, FAX NO Cost per loaded mile for delivery of sander

24 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model HI-WAY E3020 (Carbon Steel) CHASSIS MOUNT V-BOX SPREADER Standard 88" wide body is constructed of a fully welded 10-gauge hopper and stakes with 7-gauge longsills and bolt-in replaceable conveyor bottom panel. 30" wide pintle-type conveyor chain with 3/8" X 1-1/2" crossbars. This conveyor is driven by a 6:1 reduction twin-pinion spur gear drive with a hi-torque/low -speed hydraulic motor (highest efficiency-98% for lower operational and maintenance cost). Fully enclosed hydraulic drive spinner hopper with two internal deflectors, a Prior to painting, all components are chemically cleaned. Upon completion of the cleaning process, all exposed hopper seams not welded are chemically sealed. All components are then double coated with a lead- and chrome-free plural-component epoxy primer. The hopper body is painted with two finish coats of Hi-Way yellow plural-component urethane paint and then oven-cured. Bolt-on components are painted Hi-Way black urethane, oven-cured and assembled. 304 stainless steel units are unpainted (non-304 stainless steel components are painted black). All units are topped with a black decal group. Swinging rear endgate adjusts for controlled material flow and highspeed no-hoist dumping. Hi-torque/hi-speed conveyor selector valve, in-cab control valve with Note: For proper operation, hydraulic system requires GPM at 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW HI-WAY STEEL SPREADER 10' V-BOX E (7.0 cubic yard struck capacity) 17, HI-WAY STEEL SPREADER 11' V-BOX E (7.7 cubic yard struck capacity) 17, HI-WAY STEEL SPREADER 12' V-BOX E (8.5 cubic yard struck capacity) 18, HI-WAY STEEL SPREADER 13' V-BOX E (9.2cubic yard struck capacity) 19, HI-WAY STEEL SPREADER 14' V-BOX E (9.9 cubic yard struck capacity) 19, HI-WAY STEEL SPREADER 15' V-BOX E (10.7cubic yard struck capacity) 20, HI-WAY STEEL SPREADER 16' V-BOX E (11.4 cubic yard struck capacity) 21, Line Item P/N Option Description PRICE HI-WAY E3020 Inverted V, Carbon Steel, 10' HI-WAY E3020 Inverted V, Carbon Steel, 11' HI-WAY E3020 Inverted V, Carbon Steel, 12' HI-WAY E3020 Inverted V, Carbon Steel, 13' HI-WAY E3020 Inverted V, Carbon Steel, 14' HI-WAY E3020 Inverted V, Carbon Steel, 15'

25 HI-WAY E3020 Inverted V, Carbon Steel, 16' HI-WAY E3020 High-Temp Belt over Chain 10' 1, HI-WAY E3020 High-Temp Belt over Chain 11' 1, HI-WAY E3020 High-Temp Belt over Chain 12' 1, HI-WAY E3020 High-Temp Belt over Chain 13' 1, HI-WAY E3020 High-Temp Belt over Chain 14' 1, HI-WAY E3020 High-Temp Belt over Chain 15' 1, HI-WAY E3020 High-Temp Belt over Chain 16' 2, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 10' 1, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 11' 1, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 12' 2, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 13' 2, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 14' 2, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 15' 2, HI-WAY E3020 Hinged screens w/2-1/2" x 2-1/2" openings 16' 3, INTALLATION Install V-Box as rigid frame mount on chassis 1, FAX NO Cost per loaded mile for delivery of sander

26 PRICE SCHEDULE 8.0 TO PROVIDE - Make and Model HI-WAY XT3 TYPE III HYDRAULIC DUMP/SPREADER The XT3 Type III body is designed to function as a traditional dump body and as a center conveyor discharge through the tailgate. As a standard rear conveyor discharge, the 25:1 planetary drive is located at the rear of the body/conveyor. The conveyor feeds material through the adjustable feedgate, located within the tailgate, and is directed to the spinner through a chute assembly under the apron. The tailgate is double acting and will lay substantially flat for hauling brush and like items. The head sheet is flat with an internal doghouse that houses the trunnion mounted telescopic cylinder. 95.5" width for maximum capacity. The design of the side sheet/floor shall be such that the vertical surface (side wall) transforms into a horizontal surface (floor) through a large radius. This design will provide a 42" flat surface of the dump body floor allowing for the transportation of palletized materials, barrels, sign posts and other like items. 7-gauge 304 stainless steel sides and ends (85,000 psi tensile/35,000 psi yield strength). The side sheets, endgate, and head sheet are all of one-piece construction. 7-gauge 304 stainless steel full depth rear corner posts tied to a 12 channel rear apron. 304 stainless steel formed longitudinals 7-gauge inner & 7-gauge outer. One-piece 3/16 AR400 steel conveyor floor positioned 12-1/2 above the chassis frame rails. 28 wide center conveyor extending beyond the tailgate which allows for a vertical feedgate. The standard conveyor has 1/2 x 1-1/2 crossbars welded to every link. Feedgate is pin adjustable and has 8 positions to vary discharge rates. Conveyor idler and drive shafts are 2 diameter and equipped with 8- tooth drop forged steel sprockets. Dual pancake type air tailgate latch with dual over-center linkage. (Valve is not included.) Single acting, trunnion mount, nitrided telescopic hoist with 2 year warranty. 8 x 6 x 1/2 structural angle rear hinge assembly with 2 diameter 300 series stainless steel pins through 2-1/2 hinge blocks. Cylinder mounts and hinge blocks are equipped with grease fittings. Body is equipped as standard with sloped fenders. All 304 stainless steel is left unpainted. Non-304 stainless steel components are painted black. 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW HI-WAY 10' XT3 Type III Body - Rear Discharge Stainless Steel 32, HI-WAY 11' XT3 Type III Body - Rear Discharge Stainless Steel 33, HI-WAY 12' XT3 Type III Body - Rear Discharge Stainless Steel 34, HI-WAY 13' XT3 Type III Body - Rear Discharge Stainless Steel 35, HI-WAY 14' XT3 Type III Body - Rear Discharge Stainless Steel 38,178.00

27 HI-WAY 15' XT3 Type III Body - Rear Discharge Stainless Steel 38, HI-WAY 16' XT3 Type III Body - Rear Discharge Stainless Steel 39, Line Item P/N Option Description PRICE HI-WAY 10' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 1, HI-WAY 11' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 1, HI-WAY 12' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 1, HI-WAY 13' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 2, HI-WAY 14' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 2, HI-WAY 15' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 2, HI-WAY 16' XT3 Type III Body - #4 belt-over-chain conveyor - ILO standard and steel conveyor cover 2, HI-WAY XT3 Type III Body - Conveyor chain oiler - installed HI-WAY XT3 Type III Body -Conveyor motor with speed sensor HI-WAY XT3 Type III Body Double-acting hoist cylinder ILO single-acting HI-WAY XT3 Type III Body - Polyurethane spinner disc ILO steel HI-WAY XT3 Type III Body -Asphalt patching pan HI-WAY XT3 Type III Body -Rear discharge chute - carbon steel HI-WAY XT3 Type III Body -Rear mount sandbagger (no control) stainless steel 1, HI-WAY XT3 Type III Body -LED light kit - includes stop/tail/turn & clearance HI-WAY 10' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: HI-WAY 11' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: HI-WAY 12' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: 1, HI-WAY 13' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: 1, HI-WAY 14' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: HI-WAY 15' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: 1, HI-WAY 16' XT3 Type III Body - Flat Fenders ILO Sloped Fenders: 1, HI-WAY XT3 Type III Body - Pre-Wet Tank Options (Tank Only) / Installed gallon fender mount tank - 304SS (each side) 2, HI-WAY 13',14',15',16' XT3 Type III Body - Pre-Wet Tank Options (Tank Only) / Installed 95-gallon fender mount tank - 304SS (each side) 2, HI-WAY XT3 Type III Body Pre-Wet System Options / Not Installed Single tank HWXTSTS-ME - Manual Electric pre-wet system 2, HI-WAY XT3 Type III Body Pre-Wet System Options / Not Installed Dual tank HWXTSTS-ME - Manual Electric pre-wet system 2, HI-WAY XT3 Type III Body Pre-Wet System Options / Not Installed Single tank HWXTSTS-HCL - Hydraulic Closed Loop system (tank not included) 3, HI-WAY XT3 Type III Body Pre-Wet System Options / Not Installed Single tank HWXTSTS-HCL - Hydraulic Closed Loop system (tank not included) HI-WAY STEEL DUMP SPREADER 10' V-BOX E (7.0 cubic yard HI-WAY STEEL DUMP SPREADER 11' V-BOX E (7.7 cubic yard HI-WAY STEEL DUMP SPREADER 12' V-BOX E (8.5 cubic yard HI-WAY STEEL DUMP SPREADER 13' V-BOX E (9.2cubic yard HI-WAY STEEL DUMP SPREADER 14' V-BOX E (9.9 cubic yard 3, , , , , ,859.00

28 HI-WAY STEEL DUMP SPREADER 15' V-BOX E (10.7cubic yard HI-WAY STEEL DUMP SPREADER 16' V-BOX E (11.4 cubic yard , , INTALLATION Install HI-WAY Dump/Spreader Body 3, FAX NO Cost per loaded mile for delivery of sander

29 - Make and Model PRICE SCHEDULE 8.0 TO PROVIDE HI-WAY XZALT SERIES 304 stainless steel construction, the standard body width is 82". The Xzalt is able to uniformly spread granular materials alone or blended with liquid at a width of up to a 36 feet wide. The main support frame is coated with a hot dipped zinc galvanized finish for longer life with minimal maintenance. "Endless" design straight belt conveyor system installed over a stainless steel bottom panel provides for a low maintenance conveyor system capable of spreading most granular materials. The idler roller and take-up mechanism is complete stainless construction with sealed bearings, providing for low maintenance costs. The drive assembly consists of a 6:1 spur gear case providing 98% hydraulic efficiency, for lower operating and maintenance costs. The drive drum consists of a stainless shaft and drum assembly connected to the gear case through a stainless steel coupling. Positive drive, to the belt, is provided through the vulcanized rubber covering on the drum. All high wear items, such as the metering gate, spinner chute and spinner disk are stainless steel construction on both carbon and stainless steel bodies. The stainless steel metering gate has three discharge settings. No operator input or adjustment is required for rate application. This provides for a constant and highly accurate rate of discharge for all granular material. The directional spinner is vertically adjustable from 12" to 20" above the road surface. Liquid tanks with 2" fill port, and dual cross over hoses provide for quick loading and unloading of tanks. Hydraulic and electrical controls protected in stainless steel enclosure. The standard unit is equipped with domed galvanized screens - opening size of 4" x 4". The standard unit is equipped with a rear mounted fold-up inspection ladder. Precsion Placement, V-Box Style sander, for both Granular & Liquid Application 12 months from In-Service date TOTAL PRICE: SEE TABLE BELOW Dump Body Mounted Unit 'DB Xzalt - (5.2 cubic yard struck capacity w/ 465 gallon liquid capacity) 47, 'DB Xzalt - (6.4 cubic yard struck capacity w/ 585 gallon liquid capacity) 49, 'DB Xzalt - (7.5 cubic yard struck capacity w/ 700 gallon liquid capacity) 51, Chassis Mounted Unit 'CM Xzalt - (5.2 cubic yard struck capacity w/ 465 gallon liquid capacity) 42, 'CM Xzalt - (6.4 cubic yard struck capacity w/ 585 gallon liquid capacity) 45, 'CM Xzalt - (7.5 cubic yard struck capacity w/ 700 gallon liquid capacity) 46, Installation of