Terminal Block Box (Spring Type) SY3000/5000/7000 Series

Transcription

1 INFORMATION 5 ort olenoid alve Terminal lock ox (pring Type) Y3000/5000/7000 eries Compact RoH Height 6.7 mm shorter (Approx. 9% reduction) Installation area of the terminal block box Reduced by approx. 40% mm shorter (Approx. 9% reduction) Reduced work-hours! mm shorter Flat head screwdriver (Approx. 4% reduction) Lead wire pring type terminal block adopted. Crimping work using Y-terminals is not necessary. No need to tighten any retaining screws. (Torque control is not necessary.) crewless construction. No tightening of retaining screws required. A A 4A 3A 6 5A 3 pring type terminal block N umber of outputs: 3 Enclosure: I67 Connector Connecting ase ariations D-sub Connector I40 Terminal lock ox I67 New pring Type Flat Ribbon Cable C Wiring Lead Wire Circular Connector erial Transmission EX500 (8 points) EX500 (64 points) EX600 EX50 EX60 EX6 EX0 5-E666

2 Connector Connecting ase Type 0 ide orted Terminal lock ox (pring Type) Y3000/5000/7000 eries Type ottom orted RoH How to Order Manifold 5Y 3 0 TC 05 D Internal pilot Internal pilot, uilt-in silencer * 3 /5(E) port is plugged for the built-in silencer type. * W hen the built-in silencer type is used, keep the exhaust port from coming in direct contact with water or other liquids. How to Order Manifold Assembly Example (5Y3-0TC-m) -position double (4 DC) Y300-5 ( set) 3-position closed center (4 DC) Y ( set) -position single (4 DC) Y300-5 (3 sets) e sid s ion at t 3 e sid 5Y3-0TC-05D-C6 set (Type 0 5-station manifold base part no.) * Y sets (-position single part no.) * Y300-5 set (-position double part no.) * Y set (3-position closed center part no.) The asterisk denotes the symbol for assembly. refix it to the part numbers of the valve etc. T he valve arrangement is numbered as the st station from the. nder the manifold part number, state the valves to be mounted in order from the st station as shown in the figure above. If the arrangement becomes complicated, specify on a manifold specification sheet. DIN rail mounting (with DIN rail) DIN rail mounting (without DIN rail) For 3 stations pecify a longer rail than the For 4 stations standard length. 4 y A, port size (Metric/) C C3 C4 C6 C8 C0 C CM* L4 L6 L8 L0 L LM* A, port traight ymbol ø ø3. ø4 ø6 ø8 ø0 ø traight port, mixed sizes ø4 ø6 ø8 ø0 ø ø4 ø6 ø8 ø0 ø Type 0/ide ported Type /ottom ported Y3000 Y5000 Y7000 Y5000 Y7000 Elbow port, mixed sizes (Including upward and downward piping), E port size (s) ø8 ø0 ø ø0 ø A, port size (Inch/) ymbol D Manifold base (5 stations) 5Y3-0TC-05D-C6 0 3 * Enter the number of stations inside m. (Refer to DIN Rail Option above.) * Only direct mounting is available for Type (ottom ported). pward R * D ouble wiring: -position single, double, 3-position, and 4-position valves can be used on all manifold stations. se of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. * pecified layout: Indicate the wiring specifications with the manifold specification sheet. (Note that -position double, 3-position, and 4-position valves cannot be used where single wiring has been specified.) * T his also includes the number of blanking plate assembly. Elbow * t /EXH block assembly (p to 3 solenoids available) DIN Rail Option Option Direct None Name plate (with station number) AA mounting Name plate (without station number) A Without name plate Dm DIN rail Am mounting Name plate (with station number) Name plate (without station number) m N N3 N7 N9 N CM* LN3 LN7 LN9 LN N3 N7 N9 N LM* A, port traight side ( to 0 stations) ( to 0 stations) oth sides ( to 4 stations) 4 4 stations u r, E port entry ide ported ottom ported * * T he Y5000 manifold base is used for the bottom ported Y3000. When ordering, refer to the Mixed Mounting Type Manifold (Web Catalog). D 6 6 stations 0 stations pecified layout * 0 Double wiring * w Type Note ymbol Mounting Downward TC: pring type terminal block box ymbol tations 0 stations y u Mounting and Option e alve stations Y3000 Y5000 Y7000 r t e Elbow * q eries w ø/8" ø5/3" ø/4" ø5/6" ø3/8" traight port, mixed sizes ø5/3" ø/4" ø5/6" ø3/8" ø5/3" ø/4" ø5/6" ø3/8" Type 0/ide ported Type /ottom ported Y3000 Y5000 Y7000 Y5000 Y7000 Downward pward q C6 Elbow port, mixed sizes (Including upward and downward piping), E port size (s) ø5/6" ø3/8" ø/" ø3/8" ø/" * I ndicate the sizes on the manifold specification sheet in the case of CM or LM. The direction of, E port fittings is the same as for the A, port. If selecting LM, indicate it on the manifold specification sheet for the, E port fitting direction. * To avoid interference with the body or piping, select a downward elbow port when mounting the optional spacer assembly.

3 Connector Connecting ase Y3000/5000/7000 eries How to Order alves (With mounting screw) Refer to the Web Catalog for valve specifications. Y q w e r t y u i o!0! ase mounted q eries 3 Y Y Y7000 w Type of actuation ingle -position Double 3 Closed center 4 3-position Exhaust center 5 ressure center A* N.C./N.C. 4-position * N.O./N.O. dual 3-port C* N.C./N.O. * Only the rubber seal type is available for the 4-position dual 3-port valve. e eal type 0 Rubber seal Metal seal r ilot type R Internal pilot t ack pressure check valve (uilt-in valve type) None H uilt-in * Only the rubber seal type. The manifold installed type is available if the back pressure check valve is required for a valve with a metal seal. Refer to the Web Catalog for ordering example. However, it is not recommended to use the built-in valve type and the manifold installed type at the same time because it will reduce the flow. * The built-in valve type back pressure check valve is not available for the 3-position type and the Y7000. y ilot valve option tandard (0.7 Ma) Quick response type (0.7 Ma) K* High pressure type (.0 Ma) * Only the metal seal type is available for the high pressure type. u Coil type tandard T With power saving circuit (Continuous duty type) * e sure to select the power saving circuit type when the valve is continuously energized for long periods of time. * e careful of the energizing time when the power saving circuit is selected. Refer to the Web Catalog for details. i Rated voltage 5 4 DC 6 DC o Light/surge voltage suppressor and common specification ymbol With light urge voltage Common suppressor specification R Non-polar ositive Z common N Negative NZ common * Only Z and NZ types are available with the power saving circuit.!0 : Non-locking push type E: ush-turn locking lever type D: ush-turn locking slotted type F: lide locking type * Refer to the Web Catalog for the safety slide locking manual override.! Type of mounting screw Round head combination screw Hexagon socket head cap screw K Round head combination screw (Fall-out prevention type) H Hexagon socket head cap screw (Fall-out prevention type) * For K and H, the valve body cover has a drop prevention construction to stop the mounting screws from falling out when the valve is removed for maintenance etc. * When ordering a valve individually, the base gasket is not included. ince the base gasket is attached to the manifold, please order the base gasket separately if it is needed for maintenance service. Refer to the Web Catalog for base gasket and mounting screw part numbers. * and H cannot be selected for the individual /EXH spacer assembly, interface regulator, or double check spacer assembly with residual pressure release valve. rotective class class # (Mark: )

4 Y3000/5000/7000 eries Dimensions: Y3000 eries 5Y3-0TC- tations D C C3, N C4, N3 Connector Connecting ase side Type 0/ide orted Terminal lock ox (L5) L lug DIN rail holding screw (For DIN rail mounting) (DIN rail) (5) (8) (35) (5.5) ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow (40.9) ilencer (Exhaust port) (uilt-in silencer specification) (4.9) C6: 3.6 (N7: 7.4) x M4 Mounting hole (Fitting for the type with /E ports on the or both sides) 74 L.5 (5.3) (L4) (DIN rail mounting hole pitch:.5) (L3) (tation ) (tation n) [(), 3/5(E) port] Applicable tubing O.D. C8: ø8 (MC) N9: ø5/6" (MC) : Double wiring : ingle wiring /5 E 4 A (7.5) 63. (.8) 68.8 (lide locking x M0 x.5 thread depth (itch) = (7.8) [4(A), () port] Applicable tubing O.D. C: ø (MC) C3: ø3. (MC) C4: ø4 (MC) C6: ø6 (MC) N: ø/8" (MC) N3: ø5/3" (MC) N7: ø/4" (MC) n: tations L L L L L

5 Connector Connecting ase Y3000/5000/7000 eries Dimensions: Y5000 eries 5Y5-0TC- tations D C4, N3 C8, N9 Connector Connecting ase Type 0/ide orted Terminal lock ox (L5) DIN rail holding screw (For DIN rail mounting) (DIN rail) L side ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow lug (5) (8) (5.5) (35) 4.7 (6.7) ilencer (Exhaust port) (uilt-in silencer specification) (8.3) (5.9) 4 x M5 Mounting hole (Fitting for the type with /E ports on the or both sides) (5.3) 73.5 L (L4) (DIN rail mounting hole pitch:.5) (L3).5 (tation ) (tation n) [(), 3/5(E) port] Applicable tubing O.D. C0: ø0 (MC) N: ø3/8" (MC) : Double wiring : ingle wiring A (7.5) 73. (.8) 78.9 (lide locking x M0 x.5 thread depth (itch) = 6 (0.5) [4(A), () port] Applicable tubing O.D. C4: ø4 (MC) C6: ø6 (MC) C8: ø8 (MC) N3: ø5/3" (MC) N7: ø/4" (MC) N9: ø5/6" (MC) n: tations L L L L L

6 Y3000/5000/7000 eries Dimensions: Y7000 eries 5Y7-0TC- tations D C8, N9 C0, N C (L5) Connector Connecting ase L side Type 0/ide orted Terminal lock ox DIN rail holding screw (For DIN rail mounting) (DIN rail) ilencer (Exhaust port) (uilt-in silencer specification) ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow lug (8) (5) 4 A 33.8 (5.5) (35) 3.9 (77.) (7.9) (6) x M5 Mounting hole (9.3) (N3: 0.4) (Fitting for the type with /E ports on the or both sides) (A, port: ø) 73.7 L.5 (5.3) (L4) (DIN rail mounting hole pitch:.5) (L3) (tation ) (tation n) : Double wiring : ingle wiring [(), 3/5(E) port] Applicable tubing O.D. C: ø (MC) N3: ø/" (MC) [4(A), () port] Applicable tubing O.D. C6 : ø6 (MC) C8 : ø8 (MC) C0: ø0 (MC) C: ø (MC) N7 : ø/4" (MC) N9 : ø5/6" (MC) N: ø3/8" (MC) A (lide locking x M0 x.5 thread depth (itch) = 9 (.7) (0) (4.3) n: tations L L L L L

7 Connector Connecting ase Y3000/5000/7000 eries Dimensions: Y5000 eries 5Y5-TC- tations D C4, N3 C8, N9 Connector Connecting ase Type /ottom orted Terminal lock ox side lug ilencer (Exhaust port) (uilt-in silencer specification) (5) L ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow L.5 4 x M5 Mounting hole (tation ) (tation n) 89.8 (0 ) X (3.7) [E: ilot EXH port] [X : port] Applicable tubing O.D. C4: ø4 (MC) N3: ø5/3" (MC) 3/5 E E 4A (59.8) : Double wiring : ingle wiring x M0 x.5 thread depth 3 7 (.9) (9.5) (lide locking (Fitting for the type with /E ports on the or both sides) (itch) = 6 (0.5) anel fitting dimensions 8 4 A 7 Fitting dimensions for panel mounting Refer to panel fitting dimensions for details. L x M5 4 x ø5.5 [(), 3/5(E) port] Applicable tubing O.D. C0: ø0 (MC) N: ø3/8" (MC) [4(A), () port] Applicable tubing O.D. C4: ø4 (MC) C6: ø6 (MC) C8: ø8 (MC) N3: ø5/3" (MC) N7: ø/4" (MC) N9: ø5/6" (MC) n: tations L L

8 Y3000/5000/7000 eries Dimensions: Y7000 eries 5Y7-TC- lug tations D C8, N9 C0, N C ilencer (Exhaust port) (uilt-in silencer specification) 33.8 (5) Connector Connecting ase L 4 A Type /ottom orted side Terminal lock ox 96.7 ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow L.5 4 x M5 Mounting hole 93. (0 ) (tation ) (tation n) 3/5E E : Double wiring : ingle wiring (74.) (3.5) [E: ilot EXH port] [X : port] Applicable tubing O.D. C6: ø6 (MC) N7: ø/4" (MC) X x M0 x.5 thread depth 3 7 (4.5) (N3: 5.6) (A, port: ø) () 77.7 (3.9) (lide locking (Fitting for the type with /E ports on the or both sides) (itch) = (.7) Fitting dimensions for panel mounting Refer to panel fitting dimensions for details. anel fitting dimensions /5 E 3/5 E A L x M5 4 x ø5.5 [(), 3/5(E) port] Applicable tubing O.D. C: ø (MC) N3: ø/" (MC) [4(A), () port] Applicable tubing O.D. C6 : ø6 (MC) C8 : ø8 (MC) C0: ø0 (MC) C: ø (MC) N7 : ø/4" (MC) N9 : ø5/6" (MC) N: ø3/8" (MC) n: tations L L

9 Type Top orted Connector Connecting ase Terminal lock ox (pring Type) Y3000/5000/7000 eries RoH How to Order Manifold 5Y 3 TC 05 D q w e r t y u q eries 3 Y Y Y7000 w Type Top ported * Double wiring: -position single, double, 3-position, and 4-position valves can be used on all manifold stations. se of a -position single solenoid will result in an unused control signal. If this is not desired, order with a specified layout. * pecified layout: Indicate the wiring specifications with the manifold specification sheet. (Note that -position double, 3-position, and 4-position valves cannot be used where single wiring has been specified.) * This also includes the number of blanking plate assembly. How to Order Manifold Assembly Example (5Y3-TC-m) -position double (4 DC) Y330-5-C6 ( set) -position single (4 DC) Y330-5-C6 (3 sets) e alve stations TC: pring type terminal block box ymbol tations Note 0 stations Double wiring * 6 6 stations 0 stations pecified layout * (p to 3 solenoids available) 4 4 stations 3-position closed center (4 DC) Y C6 ( set) 3 tations side r, E port entry side ( to 0 stations) D ( to 0 stations) oth sides ( to 4 stations) t /EXH block assembly Internal pilot Internal pilot uilt-in silencer R * 3/5(E) port is plugged for the built-in silencer type. * When the built-in silencer type is used, keep the exhaust port from coming in direct contact with water or other liquids. y, E port size (s) ymbol Y3000 Y5000 Y7000 ø8 ø0 ø N ø5/6" ø3/8" ø/" * For N, sizes are in inches. u Mounting Direct mounting D DIN rail mounting (with DIN rail) D0 DIN rail mounting (without DIN rail) D3 D4 For 3 stations For 4 stations pecify a longer rail than the standard length. * Refer to the Web Catalog (Y3000/5000/7000 series: pecific product precautions 6) for instructions on fastening the DIN rail mounting type manifold. Manifold base (5 stations) 5Y3-TC-05D 5Y3-TC-05D set (Type 5-station manifold base part no.) * Y330-5-C63 sets (-position single part no.) * Y330-5-C6 set (-position double part no.) * Y C6 set (3-position closed center part no.) The asterisk denotes the symbol for assembly. refix it to the part numbers of the valve etc. The valve arrangement is numbered as the st station from the. nder the manifold part number, state the valves to be mounted in order from the st station as shown in the figure above. If the arrangement becomes complicated, specify on a manifold specification sheet. 8

10 Y3000/5000/7000 eries How to Order alves (With mounting screw) Refer to the Web Catalog for valve specifications. Y C6 q w e r t y u i o!0!!!3 Top ported q eries 3 Y Y Y7000 w Type of actuation ingle -position Double 3 Closed center 4 3-position Exhaust center 5 ressure center A* N.C./N.C. 4-position * N.O./N.O. dual 3-port C* N.C./N.O. * Only the rubber seal type is available for the 4-position dual 3-port valve. e eal type 0 Rubber seal Metal seal r ilot type R Internal pilot t ack pressure check valve (uilt-in valve type) None H uilt-in * Only the rubber seal type. The manifold installed type is available if the back pressure check valve is required for a valve with a metal seal. Refer to the Web Catalog for ordering example. However, it is not recommended to use the built-in valve type and the manifold installed type at the same time because it will reduce the flow. * The built-in valve type back pressure check valve is not available for the 3-position type and the Y7000. y ilot valve option tandard (0.7 Ma) Quick response type (0.7 Ma) K* High pressure type (.0 Ma) * Only the metal seal type is available for the high pressure type. u Coil type tandard T With power saving circuit (Continuous duty type) * e sure to select the power saving circuit type when the valve is continuously energized for long periods of time. * e careful of the energizing time when the power saving circuit is selected. Refer to the Web Catalog for details. i Rated voltage 5 4 DC 6 DC o Light/surge voltage suppressor and common specification ymbol With light urge voltage Common suppressor specification R Non-polar ositive Z common N Negative NZ common * Only Z and NZ types are available with the power saving circuit.!0 : Non-locking push type E: ush-turn locking lever type D: ush-turn locking slotted type F: lide locking type! A, port size Thread piping ymbol ort size Applicable series M5 M5 x 0.8 Y /8 Y /4 Y7000 (Metric) ymbol A, port Y3000 Y5000 Y7000 C ø C3 ø3. C4 ø4 C6 ø6 C8 ø8 C0 ø0 C ø (Inch) ymbol A, port Y3000 Y5000 Y7000 N ø/8" N3 ø5/3" N7 ø/4" N9 ø5/6" N ø3/8"! Thread type Rc F G N NT T NTF * Only is available for M5.!3 Type of mounting screw Round head combination screw Hexagon socket head cap screw K Round head combination screw (Fall-out prevention type) H Hexagon socket head cap screw (Fall-out prevention type) * For K and H, the valve body cover has a drop prevention construction to stop the mounting screws from falling out when the valve is removed for maintenance etc. * When ordering a valve individually, the base gasket is not included. ince the base gasket is attached to the manifold, please order the base gasket separately if it is needed for maintenance service. Refer to the Web Catalog for base gasket and mounting screw part numbers. * and H cannot be selected for the individual /EXH spacer assembly or interface regulator. * Refer to the Web Catalog for the safety slide locking manual override. 9 rotective class class # (Mark: )

11 Connector Connecting ase Y3000/5000/7000 eries Dimensions: Y3000 eries Connector Connecting ase Type /Top orted Terminal lock ox 5Y3-TC- tations D C C3, N C4, N3 side (L5) L DIN rail holding screw (For DIN rail mounting) [(), 3/5(E) port] Applicable tubing O.D. C8: ø8 (MC) N9: ø5/6" (MC) (itch) 0.5 ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow (DIN rail) lug (5) (8) ilencer (Exhaust port) (uilt-in silencer specification) E 3/5E X (5.5) (40.9) 4 x M4 Mounting hole 4.6 (35) M5 x 0.8 [4(A), () port] 74 L.5 [E: ilot EXH port] [X : port] Applicable tubing O.D. C4: ø4 (MC) N3: ø5/3" (MC) 7.4 E 3/5E X (73.8) (5.3) : Double wiring : ingle wiring 3.5 (L4) (DIN rail mounting hole pitch:.5) (L3) (tation ) (tation n) 3/5 E (5.3) 4 A [4(A), () port] Applicable tubing O.D. C: ø (MC) C3: ø3. (MC) C4: ø4 (MC) C6: ø6 (MC) N: ø/8" (MC) N3: ø5/3" (MC) N7: ø/4" (MC) (Fitting for the type with /E ports on the or both sides) (7.5) 3.6 (.8) 68.8 (lide locking ( C6: 77.3 N7: 8. ) 3/5 E 4 (73.) [E, X port] x M0 x.5 thread depth n: tations L L L L L

12 Y3000/5000/7000 eries Dimensions: Y5000 eries 5Y5-TC- tations D C4, N3 Connector Connecting ase side Type /Top orted Terminal lock ox (L5) L 78.9 (lide locking DIN rail holding screw (For DIN rail mounting) (DIN rail) (itch) = 6 ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow ilencer (Exhaust port) (uilt-in silencer specification) lug (5) (8) (6.7) E 3/5 E X (5.5) 5.5 (35) 0:6. C : [(), 3/5(E) port] Applicable tubing O.D. C0: ø0 (MC) N: ø3/8" (MC) /8" [4(A), () port] 4 x M5 Mounting hole L E 3/5 E X (5.3) : Double wiring : ingle wiring (L4) (DIN rail mounting hole pitch:.5) (L3) (tation ) (tation n) (7.4) [4(A), () port] Applicable tubing O.D. C4: ø4 (MC) C6: ø6 (MC) C8: ø8 (MC) N3: ø5/3" (MC) N7: ø/4" (MC) N9: ø5/6" (MC) (Fitting for the type with /E ports on the or both sides) [E: ilot EXH port] [X : port] Applicable tubing O.D. C4: ø4 (MC) N3: ø5/3" (MC) (69.7) A 8.7 (7.5) (.8) (9.3) (65.4) x M0 x.5 thread depth n: tations L L L L L

13 Connector Connecting ase Y3000/5000/7000 eries Dimensions: Y7000 eries 5Y7-TC- tations D Connector Connecting ase Type /Top orted Terminal lock ox (L5) L side DIN rail holding screw (For DIN rail mounting) (DIN rail) (itch) = 9 ( ush-turn locking slotted type: ress, then rotate it. ) 4(A) port side: lue (For rubber seal) () port side: Yellow lug 85.8 (lide locking (5) (8) ilencer (Exhaust port) (uilt-in silencer specification) E (5.5) 3/5E (77.) X 5.5 (35) [(), 3/5(E) port] Applicable tubing O.D. C: ø (MC) N3: ø/" (MC) /4 [4(A), () port] 73.7 L.5 4 x M5 Mounting hole [E: ilot EXH port] [X : port] Applicable tubing O.D. C6: ø6 (MC) N7: ø/4" (MC) 3/5E E X (5.3) : Double wiring : ingle wiring x M0 x.5 thread depth 3 (L4) (DIN rail mounting hole pitch:.5) (L3) [4(A), () port] Applicable tubing O.D. C6 : ø6 (MC) C8 : ø8 (MC) C0: ø0 (MC) (tation ) (tation n) C: ø (MC) N7 : ø/4" (MC) N9 : ø5/6" (MC) N: ø3/8" (MC) (A, port: ø) (Fitting for the type with /E ports on the or both sides) 4 (69.5) 88.8 (75.) A (0) (00.3) (4.3) (.) 6.5 n: tations L L L L L

14 Y3000/5000/7000 eries Terminal lock Connection tep. Remove the terminal block cover Loosen the 4 mounting screws (M3) to remove the terminal block cover. Terminal block cover Mounting screw (M3) tep. The diagram below shows the terminal block wiring. All stations are provided with double wiring regardless of the mounted valves. Connect each wire to the power supply side, according to the markings provided inside the terminal block. e sure to connect the wire with the push button pressed down. Gasket lug (Y30M-33-) is mounted Tightening torque: 0.8 N m itch 3.5 mm ush button A A 3A 4A 5A 6 3 tep 3. Mount the terminal block cover ecurely tighten the mounting screws (M3) to the torque shown in the table below only after confirming that the gasket is installed correctly. Conduit port x M0 x.5 pring type terminal block roper tightening torque [N m] 0.54 to 0.66 Applicable wire range: Conductor diameter ø0.5 to ø. mm, tranded wire AWG4 to 6 Drip-proof plug: Y30M-33- (Tightening torque: 0.75 to 0.85 N m) Electrical Wiring pecifications (I67 compatible) COM A A 3A 4A 5A 6A 7A 8A 9A 0A A A 3A 4A 5A 6A COM If alignment is not specified, the internal wiring will be double wiring (connected to OL. a and OL. b) regardless of number of stations, valve types, and option types. * When using a valve with no polarity, either positive common or negative common can be used. 3 tation tation tation 3 tation 4 tation 5 tation 6 tation 7 tation 8 tation 9 tation 0 tation tation tation 3 tation 4 tation 5 tation 6 tandard wiring Terminal no. olarity A ( ) (+) ( ) (+) A ( ) (+) ( ) (+) 3A ( ) (+) 3 ( ) (+) 4A ( ) (+) 4 ( ) (+) 5A ( ) (+) 5 ( ) (+) 6A ( ) (+) 6 ( ) (+) 7A ( ) (+) 7 ( ) (+) 8A ( ) (+) 8 ( ) (+) 9A ( ) (+) 9 ( ) (+) 0A ( ) (+) 0 ( ) (+) A ( ) (+) ( ) (+) A ( ) (+) ( ) (+) 3A ( ) (+) 3 ( ) (+) 4A ( ) (+) 4 ( ) (+) 5A ( ) (+) 5 ( ) (+) 6A ( ) (+) 6 ( ) (+) COM. COM. (+) (+) ( ) ( ) ositive Negative common common pecified Layout A mixture of single and double wiring can be specified on the manifold specification sheet. The maximum number of stations is determined according to the number of solenoids. The total number of solenoids should be 3 or less. solenoid is required for the -position single, and solenoids for the -position double, 3-position, and 4-position COM A A 3A 4A 5A 6A 7A 8A 9A 0A A A 3A 4A 5A 6A COM

15 afety Instructions e sure to read the Handling recautions for MC roducts (M-E03-3) and Operation Manual before use.