Breaker Failure Protection PSRC K2 WG

Transcription

1 Breaker Failure Protection PSRC K2 WG

2 Last Publication on Breaker Failure Protection by PSRC An IEEE PSRC Report, Summary Update of Practices on Breaker Failure Protection, IEEE Transaction Power Apparatus and Systems, Vol. PAS-101, No. 3, pp , March 1982

3 Why a Guide? Things have changed in 20 years. New Engineers need guidance. Breaker Failure Function being incorporated in multifunction relays.

4 PSRC K2 Established Working Group members

5 K2 Members Roger Hedding, Chair S.Anderson Alex Apostlov John Appleyard Roy Ball George Bartok Ron Beazer Ken Behrendt Robert Beresh Martin Best Gustav Brunello Art Buanno Zeeky Bukhala Arvind Chaudhary, Vice Chair Simon Chano Terry Crawley Randy Crellin Randy Cunico Albert N. Darlington Paul Drum Walt Elmore David Emigh Jon Ferraro Kelly Gardner Tony Giuliante George Gresko

6 K2 Members Irwin Hassenwinkle Stan Horowitz Randy Horton Mohamed Ibrahim Bob Jackson Gerald Johnson Peter Kemp Tim Kern Shoukat Khan Mike Kloiber Gary Kobet Tom Lanigan Larry Lawhead Bill Lowe Vahid Madani Walter McCannon Mike McDonald Dean Miller Pratap Mysore Mukesh Nagpal George Nail Russell Patterson Frank Plumptre Elmo Price Dan Reckerd Don Sevcik Charles Sufana Joe Uchiyama Sahib Usman Don Ware James Whatley Roger Whittaker Skip Williams Ray Young Rich Young

7 Assignment This working group will investigate issues pertaining to breaker failure protection which will include : breaker failure mechanisms, fault detectors, breaker failure circuits, effect of bus configurations, effect of multifunction microprocessor relays, and the effect of modern breaker control schemes. Prepare a guide covering the application of breaker failure protection to power circuit breakers.

8 Why Breaker Failure Protection? A B 3 FAULT 4 C LOAD LOAD 7 8 LOAD Figure 1 - Remote Breaker Clearing

9 Basic Breaker Failure Scheme BF BFI AND Timer Breaker Failure Scheme Output

10 Timing Chart PROTECTIVE RELAY TIME BREAKER INTERRUPT TIME 50BF CURRENT DETECTOR RESET TIME MARGIN TIME FAULT CLEARED TIME BFI FAULT OCCURS 62-1 BREAKER FAILURE TIMER TIME AUX TRIP RELAY TIME TOTAL FAULT CLEARING TIME LOCAL BACKUP BREAKER INTERRUPT TIME TRANSFER TRIP TIME REMOTE BACKUP BREAKER INTERRUPT TIME

11 Two Components Current Detector Breaker Failure Timer

12 Current Detector Detects current flow Pick up for minimum fault If phase current set above load current If ground current set above unbalance Drop out not delayed by dc offset Use 52a only if no current

13 Timer Longer than it takes the breaker to clear a fault Shorter than the Critical Clearing Time plus some margin. Could be longer for Line to Ground Faults than for Three Phase Faults

14 Critical clearing Time Dictated by Transient Stability limit Somewhere between 7 and 30 cycles Results from Stability Study

15 Total Clearing Time The sum of : BFI pick up + Breaker Failure Timer + Auxiliary trip relay time + Local back up breaker time + (Transfer trip time if remote)

16 Transient Stability time Severity of Fault Loading on System Mass of Generators Type of Fault

17 Circuit Breaker Failure Modes Failure to Trip Failure to Clear

18 Failure to Trip Contacts do not open after trip circuit energized. Short or open in Trip coil Mechanical problem with breaker

19 Failure to Clear Contacts open but fault not extinguished. Current continues to flow Mechanical or Dielectric problem Why auxiliary switches not reliable

20 Breaker Failure ReTrip BF BFI AND Timer Breaker Failure Scheme Output 62-2 Timer Re-Trip the Breaker (Time Delay May be Zero Time)

21 Elimination of 50BF Reset Time 50BF 62-1 Enables 50BF AND Breaker Failure Scheme Output BFI Timer

22 Addition of Control Timer BFI Control timer Enabled only after 62-1 times out 62-1 Timer 50BF Enable AND Breaker Failure Scheme Output

23 Breaker Failure Seal-In 62-1 BFI OR 50BF AND Timer Breaker Failure Scheme Output

24 Minimum Fault Current Use where current magnitude may not be enough to pick up current detector Transformers Generators Harmonic Filters

25 Minimum Fault Current BF 52a OR BFI AND Timer Breaker Failure Scheme Output

26 Ring Bus Application 21/ 79 21/ 79 Ring Bus

27 Ring Bus Separate Ct inputs into relay Careful of current distribution after one breaker opens in setting current detectors. Another Working group (K5) to look into this issue.

28 Distributed Breaker Failure GOOSE Breaker Failure Protection Relay Relay Relay Trip Fault Point

29 Design Considerations Total Breaker Failure clearing time should be less than system stability limit. Independent of type of failure detected Should operate during loss of dc to breaker

30 Conclusions BFP should operate only when desired Timer setting should allow adequate margin between backup breaker clearing and system critical clearing time. Multiple timers can be used for different types of faults Use auxiliary contacts as last resort for BFI.

31 Conclusions Phase current detectors should be set above load to protect from scheme operating during testing. Seal in circuits should be used to insure breaker failure scheme does not drop out prematurely Care should be taken when applying breaker failure to ring bus and breaker and one half.

32 Questions?