TOUCHDIAL Mini-Receiver DI-RF-REC-CV-SC H A. TOUCHDIAL Wall Paddle Dimmer DI-RF-WPD-DIM-1. TOUCHDIAL Wall Paddle Dimmer DI-RF-WPD-DIM-2

Transcription

1 TOUCHDIL Full Control System SPECIFICTION GUIDE RECEIVERS/HUBS ( RECEIVER IS REQUIRED) B TOUCHDIL Receiver DI--REC-CV- C TOUCHDIL Mini-Receiver DI--REC-CV-SC TOUCHDIL ifi Hub DI-IFI--TRMS SINGLE COLOR DIMMERS G E H F D TOUCHDIL Mini-Remote Dimmer DI--REM-DIM-1 TOUCHDIL all Paddle Dimmer DI--PD-DIM-2 TOUCHDIL all Paddle Dimmer DI--PD-DIM-1 TOUCHDIL Remote Dimmer Control DI--REM-DIM-5 TOUCHDIL all Dimmer DI--MT-DIM COLOR CONTROLLERS I SPECIFICTIONS K J Voltage¹ 12VDC/24VDC Environment² Indoor / Dry Location arranty 3-Year arranty mbient Temp³ F ( C) Operating Temp⁴ F ( C) Visit the product page at for installation guides,.ies files, voltage drop charts, and LM-79 reports. TOUCHDIL () all Control DI--MT- 12VDC TOUCHDIL Mini-Remote () Control DI--REM--1 TOUCHDIL Remote () Control DI--REM--4 *Note: TOUCHDIL Receiver may only be synced/controlled by one of the following controllers at a time. Item # Project 24VDC 2017 Elemental LED, Inc. ll rights reserved. Specifications are subject to change without notice. Toll Free: Fax: info@diodeled.com DRY LOCTION COLOR-CHNGING DJUSTBLE KELVIN DIMMBLE SPEC GUIDE TOUCHDIL Full Control System SS OF 10

2 TOUCHDIL Full Control System COMPLINCE & REGULTORY PPROVLS Safety CE Compliant Environmental RoHS Compliant COLOR-CHNGING TOUCHDIL RECEIVER TOUCHDIL Receiver DI--REC-CV- Receiver for use with color changing, adjustable kelvin, and single color applications. DJUSTBLE KELVIN (), adjustable kelvin, and single color control Input from Driver: 12-24VDC Constant Voltage Output to Load: 12-24VDC Constant Voltage Max Load: 4CH x 5, 4CH x 60 (12V), 4CH x 100 (24V) Power Failure Memory: Yes MSTER SLVE LERNING KEY GND D1+ D1 D2+ D2 DT IN/OUT TOUCHDIL Receiver OUTPUT TO LOD R C G B C POER 2.09 in in in. 1. TOUCHDIL accessories are rated to be used with 12V, or 24V DC Constant Voltage (Non-dimmable) Drivers. 2. These products are rated for indoor installation and are not protected against moisture. 3. Do not install product in an environment outside the listed ambient temperature. Exceeding the maximum ambient temperature may damage LED chips, reduce the total lamp life, lumen output, and/or adversely impact color consistency. 4. Operating temperature is measured according to the minimum and maximum ambient temperature environment. SPEC GUIDE TOUCHDIL Full Control System SS OF 10

3 B DIMMBLE TOUCHDIL MINI-RECEIVER TOUCHDIL Mini-Receiver DI--REC-CV-SC Miniature Receiver for use with single color applications. TOUCHDIL Full Control System C COLOR-CHNGING TOUCHDIL IFI HUB TOUCHDIL ifi Hub DI-IFI--TRMS ifi Hub for expanded connectivity utilizing the Diode LED ndroid or IOS mobile pp. Input from Driver: 12-24VDC Constant Voltage Output to Load: 12-24VDC Constant Voltage Max Load: 1CH, 1CH x 60 (12V), 1CH x 100 (24V) Power Failure Memory: Yes DJUSTBLE KELVIN (), adjustable kelvin, or single color control Input from Driver: 5VDC Constant Voltage Operating Frequency: 868 MHz Connections: LN OS Compatibility: ios or ndroid system Range: 300 ft. PUSH SITCH TOUCHDIL MINI RECEIVER DI--REC-CV-SC OUTPUT TO LOD POER 1.46 in. ndroid and ios Mobile pps for use with the TOUCHDIL ifi Hub may be found at Learning Key 3.74 in..78 in in. Note: The TOUCHDIL Mini-Receiver is not compatible with the DI--REM--4 TOUCHDIL Remote () Control in in. SPEC GUIDE TOUCHDIL Full Control System SS OF 10

4 TOUCHDIL Full Control System D TOUCHDIL MINI-REMOTE DIMMER E TOUCHDIL LL PDDLE DIMMER DIMMBLE TOUCHDIL Mini-Remote Dimmer DI--REM-DIM-1 One button, single zone dimmer for use with single color applications. DIMMBLE TOUCHDIL all Paddle Dimmer (Single Zone) DI--PD-DIM-1 One button, single zone wall mounted dimmer for use with single color applications. Input: 1x CR2025 3V Battery (Included) Operating Frequency: 869.5MHz / 434 MHz Input: 1x CR2430 3V Battery (Included) Operating Frequency: 868 / 869.5MHz / 434 MHz 1.5 in..5 in in. OPERTION Short press to turn ON/OFF. or decrease 3.38 in..55 in. OPERTION Short press to turn ON. Short press to turn OFF. Hold to decrease SPEC GUIDE TOUCHDIL Full Control System SS OF 10

5 TOUCHDIL Full Control System F TOUCHDIL LL DUL PDDLE DIMMER G TOUCHDIL REMOTE DIMMER CONTROL DIMMBLE TOUCHDIL all Paddle Dimmer (Dual Zone) DI--PD-DIM-2 Two button, two zone wall mounted dimmer for use with single color applications. DIMMBLE TOUCHDIL Remote Dimmer Control (Five Zone) DI--REM-DIM-5 Five zone, hand held dimmer for use with single color applications. Input: 1x CR2430 3V Battery (Included) Operating Frequency: 868 / 869.5MHz / 434 MHz Input: 1x CR2032 3V Battery (Included) Operating Frequency: 868 / 434 MHz 3.38 in in in..55 in. OPERTION ZONE 1 ZONE in..47 in. Short press to turn ON Zone 1. Short press to turn ON Zone 2. OPERTION Master Power ON/OFF Short press to turn zone LL ZONES ON. Power Indicator Indicator will flash red when data is transmitting. Short press to turn LL ZONES OFF. Short press to turn OFF Zone 1. Hold to decrease Short press to turn OFF Zone 2. Hold to decrease Single Zone Dimming Control Short press to turn SINGLE ZONE ON. Long press to increase Short press to turn SINGLE ZONE OFF. Long press to decrease 5 SPEC GUIDE TOUCHDIL Full Control System SS OF 10

6 H DIMMBLE TOUCHDIL LL DIMMER TOUCHDIL all Dimmer DI--MT-DIM Single zone, hand held, and wall mounted dimmer for use with single color applications. TOUCHDIL Full Control System I COLOR-CHNGING TOUCHDIL () LL CONTROL TOUCHDIL () all Control DI--MT- Single zone, hand held, and wall mounted color controller. Input: 1x CR2032 3V Battery (Included) Operating Frequency: MHz Magnetic Mount Removable Remote DJUSTBLE KELVIN (), and single color control Input: 1x CR2032 3V Battery (Included) Operating Frequency: 916.5MHz Magnetic Mount Removable Remote Standard Decora Plate.35 in. Magnet.35 in. Standard Decora Plate 2.59 in. Magnet 2.59 in in. OPERTION Short press to turn ON. Short Press to recall Brightness Level. Hold to save Brightness Level. Hold to decrease Short press to turn OFF. OPERTION 1.27 in. or decrease Short press to turn ON. SPEC GUIDE TOUCHDIL Full Control System SS OF 10 or decrease hite Long Press to change Color selected. Short press to turn OFF.

7 TOUCHDIL Full Control System J TOUCHDIL MINI-REMOTE () CONTROL COLOR-CHNGING TOUCHDIL Mini-Remote () Control DI--REM--1 Single zone, hand held, or wall mounted color controller. DJUSTBLE KELVIN (), and single color control Input: 1x CR2430 3V Battery (Included) Operating Frequency: 869.5MHz / 434 MHz 2.16 in in..43 in. OPERTION Hold to decrease Short press to turn ON/OFF. or decrease hite brightness only. Long Press to change Color selected. SPEC GUIDE TOUCHDIL Full Control System SS OF 10

8 TOUCHDIL Full Control System K COLOR-CHNGING TOUCHDIL REMOTE () CONTROL TOUCHDIL Remote () Control DI--REM--4 Four zone hand held color controller. DJUSTBLE KELVIN (), adjustable kelvin, and single color control Input: 3x 1.5V Batteries (Not Included) Operating Frequency: 434MHz / 868 MHz 4.72in S1 S2 S3 Note: The TOUCHDIL Remote () Control is not compatible with the DI--REC-CV-SC TOUCHDIL Mini-Receiver in in. OPERTION See TOUCHDIL PPLICTION INSTLLTION GUIDE for detailed mobile device setup and use. DYNMIC MODE CHRT Color heel djust color mixing. Zone Control Short press to control zones 1-4. Control two zones at once by pressing one zone, and then another. Long press to turn one individual zone ON/OFF. Power Press to turn all zones ON/OFF Power Indicator hite Channel Control Short press to turn CH4 ON/OFF. Long press to adjust Brightness Press to increase or decrease 8 levels of Brightness. Mode Description 1 Random Fade 2 Random Fade 3 Random Fade 4 Random Fade 5 Fade In/Out 6 Fade In Dynamic Modes Short press switches mode/pauses mode. Long press adjusts speed of dynamic mode. See Dynamic Mode Chart for mode descriptions. Save Function Save up to 3 colors. Long press to save color. Short press to retreive saved color. + S1 S2 S3 ON/OFF & hite Presets Double tap to turn channels ON/OFF. Short press for 3 variations of white created with color mixing (Neutral, Cool, arm). Useful for applications that don t utilize 4th channel for applications. 7 Fade Out 8 Skip 9 Random Fade 10 Random Fade SPEC GUIDE TOUCHDIL Full Control System SS OF 10

9 Learning Key Learning Key MSTER SLVE LERNING KEY GND D1+ D1 D2+ D2 MSTER SLVE LERNING KEY GND D1+ D1 D2+ D2 TOUCHDIL MINI RECEIVER TOUCHDIL MINI RECEIVER TOUCHDIL Receiver TOUCHDIL Receiver R C G B C R C G B C MSTER SLVE LERNING KEY GND D1+ D1 D2+ D2 MSTER SLVE LERNING KEY GND D1+ D1 D2+ D2 TOUCHDIL Receiver TOUCHDIL Receiver R C G B C R C G B C GENERL DIGRM TOUCHDIL Full Control System See TOUCHDIL INSTLLTION GUIDES for detailed connections to driver and luminaire. Max Distance Control to MSTER Receiver: 95 ft. Max # MSTER receivers paired to single zone: Unlimited Max # Controls Paired to Each MSTER Receiver: Unlimited 0 ft. 95 ft. Max Data ire Distance: 300 ft. Max Slaves ired to MSTER ithin 300 ft.: Unlimited 300 ft. TOUCHDIL ifi Hub w/ Mobile pp Control up to 8 Zones - ll Luminaires TOUCHDIL Mini-Remote Dimmer Control one Zone - Single Color Only ZONE 1 () w/ Dynamic Sync, Solid Color Dimming, K-RNGE DT IN/OUT TOUCHDIL Receiver (Set to MSTER) OUTPUT TO LOD MSTER POER DT IN/OUT DT IN/OUT TOUCHDIL Receiver (Set to SLVE) SLVE OUTPUT TO LOD POER TOUCHDIL all Paddle Dimmer Control one Zone - Single Color TOUCHDIL all Dual Paddle Dimmer Control two Zones - Single Color ZONE 2 () No Dynamic Sync, Solid Color Dimming, K-RNGE DT IN/OUT TOUCHDIL Receiver (Set to MSTER) OUTPUT TO LOD MSTER POER DT IN/OUT TOUCHDIL Receiver (Set to MSTER) OUTPUT TO LOD MSTER POER TOUCHDIL Remote Dimmer Control Control up to 5 Zones - Single Color Only TOUCHDIL all Dimmer Control one Zone - Single Color ZONE 1 Solid Color Dynamic Sync PUSH SITCH DI--REC-CV-SC TOUCHDIL Mini-Receiver POER OUTPUT TO LOD TOUCHDIL () all Control Control one Zone - Color Control TOUCHDIL Mini-Remote () Control Control one Zone - Color Control ZONE 2 Solid Color Dynamic Sync PUSH SITCH DI--REC-CV-SC TOUCHDIL Mini-Receiver POER OUTPUT TO LOD S1 S2 S3 TOUCHDIL () Remote Control Control up to 4 Zones - Color Control SPEC GUIDE TOUCHDIL Full Control System SS OF 10

10 TOUCHDIL Full Control System DDITIONL INFORMTION TOUCHDIL Control System Installation Guide TOUCHDIL Mini-Receiver Installation Guide TOUCHDIL ifi Hub Installation Guide TOUCHDIL Mini-Remote Dimmer Installation Guide TOUCHDIL all Paddle Dimmer Installation Guide TOUCHDIL all Dual Paddle Dimmer Installation Guide TOUCHDIL Remote Dimmer Control Installation Guide TOUCHDIL all Dimmer Installation Guide TOUCHDIL () all Control Installation Guide TOUCHDIL Mini-Remote () Control Installation Guide TOUCHDIL Remote () Control Installation Guide TOUCHDIL pplication Operation SFETY / RNINGS / DISCLOSURES 1. Install in accordance with national and local electrical code regulations. 2. This product is intended to be installed and serviced by a qualified, licensed electrician. 3. DO NOT connect directly to high voltage power. Install with a compatible Class 2 constant voltage LED driver (power supply). 4. Only install with a Class 2 DC Constant Voltage LED driver. 5. Only use copper wiring. Use wires rated for at least 176 F (80 C) and certified for use with external connection of electrical equipment. 6. Ensure applicable wire is installed between driver, fixture, and any controls in-between. hen choosing wire, factor in voltage drop, amperage rating, and type (in-wall rated, wet location rated, etc.). Inadequate wire installation could overheat wires, and cause fire. 7. This product is rated for indoor installation and is not protected against moisture. 8. Do not install in environment where excessive heat may exist (ex. close proximity to fireplace, etc.) See mbient Temperature ratings 9. Do not modify product beyond instructions or warranty will be void. 10. e reserve the right to modify and improve the design of our controls without prior notice. e cannot guarantee to match existing installed system for subsequent orders or replacements in regards to product appearance, or operation. RRNTY Limited arranty This product has a three (3) year limited warranty from the date of shipment. This warranty does not include the additional accessories referenced in this specification sheet. Complete warranty details for fixtures and additional accessories are available at limited-warranty/ within the Policies section. For warranty related questions please contact product support. Consumer s cknowledgment Elemental LED, Inc. stands behind its products when they are used properly and according to our specifications. By purchasing our products, the purchaser agrees and acknowledges that lighting design, configuration and installation is a complex process, wherein seemingly minor factors or changes in layout and infield adjustments can have a significant impact on an entire system. Choosing the correct components is essential. Elemental LED is able to work with the original purchaser to make an appropriate product selection to the extent of the limited information that the customer can provide, but it is virtually impossible for Elemental LED to design a system that foresees every unknown factor. For this reason, this arranty does not cover problems caused by improper design, configuration or installation issues. ny statement from an Elemental LED employee or agent regarding a customer s bill of goods and/or purchase order is NOT an acknowledgment that the products purchased are designed and configured correctly. The purchaser agrees and acknowledges that it is the customer s responsibility to adhere strictly to all information contained in the Product Specification Sheets. There is often more than one way to design, configure and layout an LED lighting application properly to achieve the same lighting effect. Elemental LED strongly recommends that licensed professionals be used in the design and installation of lighting systems that include Elemental LED products. The specifications include important information that a designer and installer should carefully review and strictly follow. Qualified designers and certified and/or licensed installers, with access to the final installation environment, customer goals, and Elemental LED product specifications can make the requisite decisions appropriate for a successful finished lighting application Elemental LED, Inc. ll rights reserved. Specifications are subject to change without notice. Toll Free: Fax: info@diodeled.com SPEC GUIDE TOUCHDIL Full Control System SS OF 10