HYDROLUME SLIM RGB LED Strip Light

Transcription

1 HYDROUME SIM R ED Strip ight COOR-CHAI 4VDC UV RESISTAT DRY/WET OCATIO IP68 SAFETY & WARIS QUICK SPECS / MODES 1. Install in accordance with national and local electrical code regulations.. This product is intended to be installed and serviced by a qualified, licensed electrician.. Do not modify or disassemble this product beyond instructions or the warranty will be void. 4. All plastics are affected by the elements and may shift in color and other properties after product installation, particularly with direct exposure to sun, chlorinated water, and other chemicals. 5. Only install with a isted Class DC ED driver. 6. To avoid Voltage Drop, ensure wire gauge used with ED Strip ight is sufficient to keep under % voltage drop. 7. Do not exceed maximum run recommended for Strip ight. 8. Diode ED Strip ight is designed to be cut at designated cut points only. Cutting anywhere other than the cut points will result in damage to the Strip ight. 9. Failure to follow safety warnings, and installation instructions will void the warranty for this product. Input Power Max Run Ambient Temp 4VDC Constant Voltage W/ft. (1.5W/cut point) 6 ft F (-0-60 C) Do not install product in environment outside listed temperature. POWER SUPPY CASS HYDROUME SIM R ED STRIP IHT 1 OF 6 I

2 HYDROUME SIM R ED Strip ight PRE-ISTAATIO HADE PRODUCT WITH CARE! ADDITIOA ACCESSORIES Mounting racket DI-HS-MTR 4 in. DO OT ED ED STRIP IHT TO A DIAMETER ESS THA 4 ICHES. DO OT ED ED STRIP IHT O A HORIZOTA PAE. Mounting Channel DI-HS-MTCH DO OT COVER STRIP IHT WITH AY MATERIAS. COECTOR COMPRESSIO HYDROUME Connectors may become compressed during shipping. To decompress, insert flathead screwdriver under top of connector and apply upward pressure until pins are completely removed from opening. DO OT FOD, CREASE, OR TWIST ED STRIP IHT. DO OT POWER STRIP IHT WHIE ATTACHED TO SPOO OR TIHTY COIED. WIRE AUE & VOTAE DROP Ensure appropriate wire is installed between driver, fixture, and any controls in between. When choosing wire, factor in voltage drop, amperage rating, and type (in-wall rated, wet location rated, etc.) For more information, refer to system diagrams and voltage drop charts at the end of this document. HYDROUME SIM R ED STRIP IHT OF 6 I

3 HYDROUME SIM R ED Strip ight ISTAATIO REQUIRED COMPOETS 1 TUR POWER OFF AT CIRCUIT 1 REAKER AC I MASTER SAVE EARI KEY D1+ D1 D+ D D DATA I/OUT TOUCHDIA Receiver V V W WW R W CW W WW W CW W POWER IPUT V 5 4 SHOCK HAZARD! May result in serious injury or death. Turn power OFF at circuit breaker prior to installation. OUTPUT TO OAD DC OUT Appropriate Junction ox Class rated Driver Color Controller HYDROUME SIM R ED Strip ight HYDROUME SIM Mounting rackets or Channels HYDROUME SIM R Connectors and other accessories REQUIRED TOOS DETERMIE OCATIO TO ISTA COMPOETS REMOVE PROTECTIVE FIM FROM HYDROUME SIM R STRIP IHT Clear protective film is included on back of HYDROUME SIM R ED Strip ight. Peel film from Strip ight before mounting. 4 Flathead Screwdriver Ruler Wire Stripper Wood Screws HYDROUME SIM R ED STRIP IHT OF 6 I

4 HYDROUME SIM R ED Strip ight ISTAATIO (COT.) 4 MOUT HYDROUME SIM R ED STRIP IHT TO SURFACE See mounting options a, & b (below). 5 ATTACH COTRO AD DRIVER Verify compatible driver is installed. Utilize applicable wiring when installing outdoors. (Use of wet location-rated junction box recommended) a HYDROUME SIM MOUTI RACKETS 6 REVIEW SYSTEM Mark placement for HYDROUME SIM Mounting rackets -- roughly 1 inches apart. Fasten brackets with M.9 (#4) screw or similar size (not provided). Once mounted, fasten HYDROUME SIM R ED Strip ight to brackets. 7 Ensure all polarities are correct and connections are secure. TUR POWER O AT CIRCUIT REAKER TROUESHOOTI b HYDROUME SIM MOUTI CHAE Mount channel to desired surface using minimum x M.9 (#4) screws or similar size (not provided). Once channel is mounted, firmly press HYDROUME SIM R ED Strip ight into channel pressing one end to the other. Shift in brightness and/or kelvin Some EDs are not functional ights are flickering Ensure an appropriate gauge of wire is installed between strip light and ED driver. See VOTAE DROP CHARTS. Ensure strip light has not been bent excessively, which could damage circuitry. Ensure a compatible driver and/or dimming control is installed. Check for loose connections. ights are turning on/off repeatedly Ensure driver is not overloaded. An overloaded driver will trip the internal auto-reset (of driver) repeatedly, turning the system on/off. HYDROUME SIM R ED STRIP IHT 4 OF 6 I

5 RU SYSTEM DIARAMS HYDROUME SIM R ED Strip ight The following diagrams are provided as example system designs. For information regarding larger systems or systems not pictured below, please see our web page or contact technical support. Always review each component installation guide for detailed and up-to-date wiring instructions. Install in accordance with national and local electrical codes. R/RW COOR COTRO SYSTEMS AC Power 50/60Hz Install applicable wire gauge / type * IPUT Class ow Voltage Driver Installed in Junction ox Address Setting Power DC+ DC OUTPUT Output R W R (RW) Controller W R ADDITIOA COOR COTRO SYSTEMS TOUCHDIA, ATTRIUTE, and other control system diagrams are available on-line at RW Strip ight / Fixture 8 DMX COTRO SYSTEM Class ow Voltage Driver 1 Installed in Junction ox DMX Controller Installed in Wall ox AC Power 50/60Hz * IPUT OUTPUT DMX Data Output + - Power Input Power input of DMX controllers may vary. See DMX controller specifications to ensure appropriate high or low voltage power input. RJ45 Splice Cable Wiring Connections Install applicable wire gauge / type CAT5 / Ethernet Cable (RJ45 Connections) CH1 - R Data I CH - CH Data OUT CH4 - W DMX Decoder CH1 - R CH1 R CH CH CH1 R RJ45 Coupler RJ45 Splice Cable R Tape ight / Fixture rown round White/Orange Data + Orange Data - White/rown wire may be used as an additional ground. Data I Data OUT CH - CH - CH4 - W CH CH CH4 W RW Tape ight / Fixture DMX Decoder CH4 - W connection only utilized for RW / R(X) installation. 1. Driver may not require a fault ground connection. Refer to driver specifications for additional information.. See fixture specifications for maximum series run limits. HYDROUME SIM R ED STRIP IHT 5 OF 6 I

6 HYDROUME SIM R ED Strip ight VOTAE DROP CHARTS For best performance and lumen output, ensure proper wire gauge is installed to compensate for voltage drop of low voltage circuits. Example: 4V Voltage Drop & Wire ength Distance Chart Wire auge 10 W.4 A 0 W.8 A 0 W 1. A 40 W 1.7 A 50 W.1 A 60 W.5 A 18 AW 14 ft. 68 ft. 45 ft. ft. 7 ft. ft. 16 AW 15 ft. 109 ft. 7 ft. 54 ft. 4 ft. 6 ft. 14 AW 45 ft. 174 ft. 115 ft. 86 ft. 69 ft. 57 ft. 1 AW 59 ft. 7 ft. 181 ft. 15 ft. 108 ft. 90 ft. 10 AW 784 ft. 97 ft. 6 ft. 197 ft. 158 ft. 11 ft. 1 Determine load size. et s assume load is 55 W. Round up to nearest load. Determine distance from driver to load. et s assume the distance is 90 ft. It is recommended to install 1 AW to eliminate excess voltage drop. 4V Voltage Drop & Wire ength Distance Chart Wire auge 10 W.4 A 0 W.8 A 0 W 1. A 40 W 1.7 A 50 W.1 A 60 W.5 A 70 W.9 A 80 W. A 100 W 4. A 18 AW 14 ft. 68 ft. 45 ft. ft. 7 ft. ft. 19 ft. 17 ft. 14 ft. 16 AW 15 ft. 109 ft. 7 ft. 54 ft. 4 ft. 6 ft. 1 ft. 7 ft. ft. 14 AW 45 ft. 174 ft. 115 ft. 86 ft. 69 ft. 57 ft. 49 ft. 4 ft. 6 ft. 1 AW 59 ft. 7 ft. 181 ft. 15 ft. 108 ft. 90 ft. 77 ft. 68 ft. 56 ft. 10 AW 784 ft. 97 ft. 6 ft. 197 ft. 158 ft. 11 ft. 11 ft. 98 ft. 8 ft. Toll Free: Fax: info@diodeed.com 019 Elemental ED Inc. All rights reserved. Specifications are subject to change without notice. HYDROUME SIM R ED STRIP IHT 6 OF 6 I