MUSTANG PROJECT. INSTALLING THE Mustang Project LED SEQUENTIAL TAILLIGHT KIT P/N MP-2004-LED AND MP-2004-LED-QK. Price:$9.
|
|
- Barbara Park
- 5 years ago
- Views:
Transcription
1 VOLUME 6 Price:$9.95 A SafeCode Inc. Publication INSTALLING THE Mustang Project LED SEQUENTIAL TAILLIGHT KIT P/N MP-2004-LED AND MP-2004-LED-QK
2 Page 2 Read these instructions carefully before installing your Taillights!!! Components included in your kit: Your kit includes 6 Flamethrower LED modules especially designed for your late model mustang. Wire connectors ( 6 ) instructions are also included. Tools Required for Installation: ¼ Drive 11mm Deep Well or 11mm Wrench T-30 Torx Bit with Driver Small Flat Screwdriver
3 Housing Removal: Page 3 It is not necessary to remove the housing from the car or to disconnect the wire harness. The housing is shown here removed from the car for clarity only. Make sure the lights are turned off and the ignition is off before you proceed further. Remove all of the turn/driving lamps from each housing ( 6 lamps total ).
4 Page 4 Attach wire tap connectors Start by attaching 1 wire tap connector per car side. It is not necessary to remove the harness from the car or to modify the harness by cutting it in any way. Apply connectors on each side as follows: On one side of the car: Apply a wire tap connector on the Orange/Blue or Grey -stripe wire which exits the middle lamp socket this will be the orange with blue stripe wire which exits the socket near the edge of the socket( see white arrow). Do not attach the wire tap connector to the wire exiting from the middle of the socket or to the black wire exiting the socket. On the other side of the car: Apply a wire tap connector on the Green/Orange -stripe wire which exits the middle lamp socket this will be the green with orange stripe wire which exits the socket near the edge of the socket( see white arrow). Do not attach the wire tap connector to the wire exiting from the middle of the socket or to the black wire exiting the socket.
5 Page 5 Attach Wire Tap Connectors:.
6 Page 6 Insert the LED modules as follows: 1) Install the inner most LED module first. All of the LED modules are inserted into the socket so that the microprocessor faces TOWARDS the wires exiting the socket. This module has a black wire and sub-harness connected to it. Insert the module as shown. Be careful to allow the small diameter black wire to exit the housing under the rubber washer so that it is not pinched by one of the locking tabs on the inner socket. 2) Install the middle LED module. Again be sure that the modules are inserted into the socket so that the microprocessor faces TO- WARDS the wires exiting the socket. Install LED Modules:
7 Page 7 Make Connections: 3) Install the outer LED module in the same way. be sure that the modules are inserted into the socket so that the microprocessor faces TOWARDS the wires exiting the socket. Sub-Harness Connections: Now make the sub harness connections as follows: 1) Connect the black wire from the subharness to the wire tap connector you previously installed on the middle socket. Do this for both housings on each side of the car. The inner LED module sub-harness will connect here as shown. The black wire will exit the most inner lamp socket under the gasket and connect at the wire white/redstripe tap connector. Make this connection on both sides Black of the car white/redstripe Green Green Black
8 Page Mustang Flasher Installation MP-2004-LED-QK The flasher is located on drivers side of the car next to hump under the dash. Unplug the OEM square 5 pin module and replace. Simply plug-in directly the new module pictured above. The plug cannot be plugged in wrong as it is polarized. Remove OEM flasher and plug new flasher module in here.
9 Page 9 Test the taillights BEFORE securing the light housings to your car. Before testing complete the installation on both sides of the car. The computer control in the Mustang will have to be reset by removing the negative battery terminal and re-connecting it if testing is not done with both side installed properly. Do all testing with the LED modules installed on both sides of the car. Do not reinstall the housings until testing is complete however. Test as follows: Start the car or turn the ignition to on or accessory. 1) With the headlights off have someone step on the brake. Make sure both sides sequence one and stay on. 2) With the headlights off activate the turn signal on each. Ensure that the taillights sequence from inside to outside. If a module has been placed in the wrong socket you will see improper sequencing order. Just move the module to the correct socket. Remember that the inside socket must hold the LED module with the sub harness connected. 3) Now repeat the above with the headlights on. You will notice that during turn signaling the light sequence from dim to bright this is correct operation. Troubleshooting: 1) Some LED modules do not light. Make sure that you have the modules installed in the right polarity in each socket. The microprocessor must face AWAY from the socket wires. See pictures. 2) Sequencing is in the wrong order. Make sure you have installed the correct modules in the correct socket. GREE N 3) Lamps sequence rapidly but not properly. Make sure the subharness is connected properly. Be ORANGE/BLUE sure the harness connector blades are inserted properly into the wire-tap connectors. A properly inserted connector hides the blade in the wire tap connector BLACK
EU DLX LED Tail-Light Kit Installation:
WWW.MUSTANGPROJECT.COM Page 1 1964.5-1966 EU DLX LED Tail-Light Kit Installation: First we will remove the old original flasher module. The original flasher module will be located on the driver side of
More informationConvert from original 1969 Mustang style taillights to Shelby Style!
WWW.MUSTANGPROJECT.COM VOLUME 6 Price:$9.95 MUSTANG PROJECT A SafeCode Inc. Publication INSTALLING THE MUSTANG PROJECT SHELBY SEQUENTIAL CONVERSION KIT ON YOUR 69 MUSTANG Convert from original 1969 Mustang
More informationMUSTANG PROJECT INSTALLING THE MUSTANG PROJECT SHELBY SEQUENTIAL CONVERSION KIT ON YOUR MUSTANG
VOLUME 6 Price:$9.95 MUSTANG PROJECT A SafeCode Inc. Publication INSTALLING THE MUSTANG PROJECT SHELBY SEQUENTIAL CONVERSION KIT ON YOUR 64.5-66 MUSTANG Convert from original 1964.5-66 Mustang style taillights
More informationComponents included in your kit:
Page 1 Components included in your kit: All of the equipment illustrated in this manual was proudly manufactured in the USA by Mustang Project a SafeCode Inc. enterprise. For accessories and spare parts
More informationComponents included in your kit:
Page 1 Components included in your kit: The LED flasher module will replace your existing flasher module. The left and right taillight modules will replace your existing All of the equipment illustrated
More informationTurn Signal / Horn Kit PN 7101 by All years Polaris RZR 1000 and RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED
All years Polaris RZR 1000 and 1000-4 2015 RZR 900, 900-4, 900 trail, 900S and 900XC STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODEL POLARIS RZR 1000 AND 1000-4. ALSO THE 2015 POLARIS RZR
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory TRIM Application 2009 ACCORD 4-DOOR Publications No. AII 40008 Issue Date JULY 2008 PARTS LIST Steering Wheel Trim (Without Navigation) P/N 08Z13-TA0-100 Right steering
More informationInstalling LED courtesy lights in Mustang.
Installing LED courtesy lights in 2005 2010 Mustang. This procedure is to provide you with the basics for installing LED strips under the dash and changing the map or courtesy lights to LED. Use the Ford
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 23302 2002 MDX Issue Date PN 08U97-S3V-210 (BLACK) P/N 08U97-S3V-270 (SADDLE) NOV 2001 PARTS LIST Wood trim steering wheel 1. Make sure
More informationClassicLEDs LLC. Sequential LED System
ClassicLEDs LLC 1967 and 1968 Mustang Sequential LED System CLE30015S Thank you for your purchase. This is the latest design of our 1967 and 1968 Mustang sequential LED system. There have been several
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 37248 2008 TSX Issue Date JUNE 2007 PARTS LIST 1. Make sure you have the anti-theft code for the radio, then write down the frequencies
More informationSequential Tail Light System
Sequential Tail Light System Installation Instructions Notice: Our conversion systems are intended for 1965-70 Ford Mustangs only. This is not a replacement system for Shelby Mustangs or Mercury Cougars
More informationFord Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List:
2015-2017 Ford Mustang V6 OEM-Style Fog Light Kit Parts List: Quantity: Tool List: LED Foglights/ Bezels 2 Flat head & Phillips screwdriver (if you ordered part#3600) Ratchet & Socket set OR Wiring harness
More informationDepress each tab as you pull the bezel off. The bezels are tight. L.H. shown.
2013-2014 Ford Mustang V6 & Boss 302 Lower Valance Fog Light Kit Parts List: Quantity: Tool List: Fog light & bulb with bracket 2 Flat head & Phillips screwdriver Black bezels 2 Ratchet & Socket set OR
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SNA-100 2007 CIVIC HYBRID AII 33829 Issue Date SEP 2006 PARTS LIST Fog light harness Right fog light Left fog light Subharness
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-100 2006 CIVIC 2-DOOR All 30890 Issue Date SEP 2005 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped
More informationInstallation Instructions
Installation Instructions Jeep JK Unlimited (2007 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Bracket for ARB Compressor
More informationInstalling the STS-4CH Dodge Challenger Sequential Turn Signal System
Installing the STS-4CH 2008-2010 Dodge Challenger Sequential Turn Signal System The STS-4CH is an exciting addition to your 2008-2010 Dodge Challenger. This Plug-N-Play system comes complete with pre-wired
More informationINSTALL INSTRUCTIONS
INSTALL INSTRUCTIONS Models: 6005 & 6005TK (For Non Electric Mirrors) GM CK Body Style If your stock mirrors are stock electric the wrong set has been ordered. Do not attempt to manually extend or retract
More informationRemove black panel shown. Save 6 retaining pins for re-install later. Pry up on center part of pin first. Then pry out entire retaining pin.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver Supplemental wire leads 2 Ratchet & Socket set OR Wire tap red 2 Adjustable Wrench
More informationRemove 4 circled pins. Route wiring along dashed line. Remove the 2 9mm nuts and black retaining plate that secure extractor.
2015 Ford Mustang Turn Signal Hood Kit Parts List: Quantity: Tool List: Bracket & pre-installed lamp 2 Flat head screwdriver Wiring harness 1 Phillips screwdriver PB-3660 Parts Bag 1 Ratchet & Socket set
More information2005 and 09 Mustang install instructions Sequential / Chase Unit Partial Plug-N-Play Kit Meter4it Eng. Updated: 3/28/09
Updated: 3/28/09 Verify content of kit: 1- Unit with wiring harness 1- Red power wire with 15 amp fuse 1- Color instruction 2- Velcro for mounting 1-Driver taillight harness 1- Passenger taillight harness
More informationCVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing
CVO - with ipod Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 5/16 inch Socket Phillips Screwdriver 1/2 inch
More informationLiteDOT Installation Document
LiteDOT Installation Document This document designed to aid in installation of LiteDOT s on Jeep TJ models, other models are similar. NOTE: Installing LiteDOT s on a Jeep where the 2 necessary mounting
More information2015 Ford F150 Rear Bumper w/ LED
2015 Ford F150 Bumper w/ LED T527990 T527991 PARTS LIST: 1 Bumper Assembly 4 12mm Lock Washers 2 Mounting Brackets 6 12 mm Nylon Lock Nuts 4 Sensor Hole Plugs 8 4mm x 10mm Button Head Bolts 2 Plastic Plugs
More informationECO-SERIES REAR BUMPER FORD F150 PART # FD-2962
15-16 FORD F150 PART # FD-2962 Body Armor 4x4 272 Corporate Terrace St. Corona, CA 92879 951-808-0750 Customer Service hours: M-TH: 7:30am to 4:30 PM Pacific Time Friday: 8 AM Noon Pacific Time PARTS LIST:
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. CIVIC AII 24171 S 2- AND 4-DOOR Issue Date (DX, HX) AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationREAR ROOF SPEAKER KIT
REAR ROOF SPEAKER KIT P/N 2882876 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationBarton Short Throw Shifter 11/12 V6, GT Mustang:
Barton Short Throw Shifter 11/12 V6, GT Mustang: Tools Required: 10mm deep socket Socket wrench 10 extension for socket wrench Jack Jack stand Small piece of wood Small hook tool (recommended) *can be
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SVA-110 2007 CIVIC 2-DOOR All33536-34848 Issue Date FEB 2007 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. ATTACHMENT (EX-L WITH NAVI) 2008 RIDGELINE AII 36587 Issue Date MAY 2007 PARTS LIST Attachment Kit P/N: 08B21-SJC-102 Template Rear camera
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory LED FOGLIGHT ATTACHMENT KIT P/N 08V70-MKC-A00 Application GL1800/B/BD/D/DA Honda Dealer: Please give a copy of these instructions to your customer. Publication No. MII
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 24570 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2003 MDX Issue Date OCT 2002 PARTS LIST Wood steering wheel 1. Make sure
More informationHow to Install a 997, Boxster, & Cayman Radio
How to Install a 997, Boxster, & Cayman Radio Step-by-step instructions for a 997.1, Boxster, & Cayman Radio Installation. *Credit to CAI- Store.com for this Guide* Written By: Danielle 2017 guides.drivediy.com
More informationFog Lamp Instructions
Fog Lamp Instructions 2011+ Ford Super Duty Congratulations on your purchase of a high quality PUTCO product. Should you need any application or technical assistance feel free to call us at: 1-800-247-3974
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2010 INSIGHT Publications No. AII 40881 Issue Date MARCH 2009 PARTS LIST Right fog light bracket D Fog Lights Kit P/N 08V31-TM8-100 Left fog light Fog
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 39890 2009 MDX Issue Date JULY 2008 PARTS LIST Backup Sensor Attachment Kit P/N 08V67-STX-200A Self-tapping screw, 5 x 16 mm 12 Wire
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. 2007 CIVIC 2-DOOR All33536-34068 Issue Date SEP 2006 PARTS LIST 11 Wire ties Right fog light Clip Left fog light 4 Stepped screws 2 Washer
More informationGENUINE ACCESSORIES INSTALLATION INSTRUCTIONS FOG LIGHT KIT
PART NUMBER: 0000-8F-H99 ( 09-10) 0000-8F-H89 ( 11 - ) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS FOG LIGHT KIT APPLICABLE MODELS: 2009> MAZDA6 NOTE: Supplemental combination switch is required for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. S CIVIC 2 AND 4-DOOR (EX, LX) AII 24188 Issue Date AUG 2002 NOTE: Fog Lights cannot be installed if the vehicle is equipped with an optional
More informationINSTALLATION INSTRUCTIONS
OEM Tailgate Camera/Bezel Assembly with Chassis Harness 2014-current Chevrolet Silverado and GMC Sierra (Kit part number 9002-1005) Kit Contents: Chassis Harness 1 bubble bag containing: Tailgate Handle
More informationProcedure. These guidelines can be found in the "Accessory Installation Practices" document.
Toyota Tundra 207 LED Illumination Package Part Number: 0006-00069 (Interior and Exterior) Accessory Code: LL000 Conf licts V ehicles with Option Code BZ Color Applicability/Trim Level Kit Content 4 Puddle
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. BII 25831-26975 P/N 08U97-S3V-210A (BLACK) P/N 08U97-S3V-220A(SADDLE) 2004 MDX Issue Date MARCH 2004 PARTS LIST Wood steering wheel 1. Make
More informationNot Included. Rear Half Harness
Basic Light Kit 60102 Caution! Wear appropriate eye protection! Disconnect the battery or batteries. Place run/tow switch in tow position before disconnecting the batteries on models using that feature.
More informationConflicts: Vehicles with a sunroof
Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:
More informationACD-PRO Install in 2008 EvoX
Turning in a counter clockwise direction, unscrew ift knob ACD-PRO Install in 2008 EvoX Slide back and remove the floor console panel assembly Pull up to remove the center console tray Disconnect the plug
More informationInstallation Instructions
Installation Instructions Jeep JK 2-Door (2011 Present) Mounting Bracket and Air Line System Kit for ARB On-Board Twin Air Compressor (CKMTA12) Made in the USA Kit Contents: 1 Flat Bracket 1 Formed Bracket
More informationPush Start Ignition (05-10 All) Installation
Tools Required: Phillips head screwdriver Flat head screwdriver Ratchet 7mm Socket Torx T20 bit Wire strippers/cutters Hand file Needle nose pliers Installation Instructions: Push Start Ignition (05-10
More informationHow To: Convert Headlight DRLs Into Marker DRLs A CFans Members Mod Project by burn
How To: Convert Headlight DRLs Into Marker DRLs A CFans Members Mod Project by burn Skill Level: Easy Disclaimer: Please use caution and seek professional assistance when necessary. ColoradoFans.com, the
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SNA-100D Application 2010 CIVIC 4-DOOR Publications No. AII 42452 Issue Date SEP 2009 PARTS LIST Right fog light 6 Wire ties Left fog light Clip Switch harness
More information*70200BAG1* 70200BAG FORD F150 GRILLE LIGHT MOUNT
927020000 *70200BAG1* 70200BAG1 2015-2018 FORD F150 GRILLE LIGHT MOUNT PRIOR TO INSTALLATION Make sure the kit is complete and you have read these instructions thoroughly before beginning installation.
More informationINSTALLATION INSTRUCTIONS HEAVY DUTY FRONT BUMPER CHEVY SILVERADO 1500
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Heavy Duty Bumper Assembly 16 12mm Nylon Lock Nuts 1 Driver Mounting Bracket 8 4mm x 10mm Socket Head Screws 1 Passenger Mounting Bracket 4 Sensor Plugs 4 Support
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2011 PILOT Publications No. AII 43298 Issue Date MARCH 2010 PARTS LIST Back-up Sensor Attachment Kit P/N 08V67-SZA-100A Back-up sensor harness Fuse label
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V31-SZT-100 Application 2012 CR-Z Publications No. AII 46896 Issue Date OCT 2011 PARTS LIST Left fog light Relay Right fog light 20A Fuse Fuse label Left fog
More informationCLASSIC UPDATE WIRING KIT
by Randy Irwin 1955-57 CLASSIC UPDATE WIRING KIT Randy Irwin - Technical Writer Randy has been involved in the Chevy parts business for over 25 years. He is a wizard at creating, making and modifying custom
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. XM SATELLITE RADIO SYSTEM (EX) 2008 PILOT All 37110 Issue Date JUN 2007 PARTS LIST XM Radio Attachment (sold separately) P/N 08B15-S9V-100A
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SNA-100 2008 CIVIC 4-DOOR AII 37730 Issue Date AUG 2007 PARTS LIST Fog light harness Right fog light Left fog light Sub harness
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Heated Grips Kit P/N 0ST71-HR3-A00 Application After 13 TRX420 All (except 14 TRX420FA/FPA) After 13 TRX500 All (except 14 TRX500FA/FPA) Honda Dealer: Please give a
More information18SP675Rev. MBE 900 Grid Heater Relay Installation Instructions (P/N: A )
18SP675Rev. MBE 900 Grid Heater Relay Installation Instructions (P/N: A9061590004) KIT DESCRIPTION Kit P/N: A9061590004 includes a relay and bracket assembly for installation on all EPA04 and EPA07 MBE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application 2008 ACCORD 2-DOOR Publications No. AII 37561-38377 Issue Date NOV 2007 PARTS LIST Control unit bracket (L4) Back-up Sensor Attachment Kit P/N 08V67-TE0-100A
More informationAmp & Speaker Upgrade Install Instructions for Victory Cross Country
Amp & Speaker Upgrade Install Instructions for Victory Cross Country Tools Needed: 13mm Socket 4mm Ball Head Allen Socket 5mm Allen Wrench 10mm Wrench Wire Cutters Wire Strippers Phillips Screwdriver Pocket
More informationLGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions
LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions Caution: Please read through the instructions carefully. Before starting this project, remove the system s positive and
More informationGentex by VOXX Corporation Installation Instructions
Gentex by VOXX Corporation Installation Instructions Bezelled ADVGEN45A4 Bezelled w/ Homelink ADVGEN80EXP ADVGEN45A4PW4 ADVGEN40A4 Frameless ADVGEN8EXP Frameless w/ Homelink ADVGEN85EXP ADVGEN45AB5 TOOLS
More informationSmall knife. Remove black panel shown. Save 6 retaining pins for re-install later.
2005-2009 Ford Mustang V6 Fog Light Wiring Kit Parts List: Quantity: Tools Required: Wiring harness 1 Flat head screwdriver PB-3425 Parts Bag 1 Ratchet & Socket set OR Ford OEM Switch (if you 1 Adjustable
More informationMustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC #
1990-1993 Mustang CLASSIC LIGHT BAR INSTALLATION INSTRUCTIONS CDC # 101000 Kit Components: 1 Light Bar 4 Bolts ( 5 / 16-18 x 2.5 ) #182010 4 Washer #182005 4 Shims #182009 2 Dark Blue Connectors #182004
More informationAmp & Speaker Upgrade Install Instructions for Road Glide
Amp & Speaker Upgrade Install Instructions for Road Glide Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 10 mm Socket Phillips Screwdriver 1/2 inch Ratchet Wrench T25 Torx driver
More informationINSTALLATION. Note: Not all of the included parts will be used during this installation. -cont.-
Driving Lights for Road Glide 5007 Fits: 98-up Road Glide PartS Included 1 Right Light Assembly 1 Left Light Assembly 1 Right Mounting Bracket 1 Left Mounting Bracket 1 Hardware Kit Including: 2 Narrow
More informationWolverine Turn Signal / Horn Kit 2102
All years Yamaha Wolverine STOP - THIS KIT IS DESIGNED SPECIFICALLY FOR ALL YEAR AND MODELS YAMAHA WOLVERINE. IF YOUR MACHINE IS NOT ONE OF THESE MODELS DO NOT PROCEED. Contact Ryco Motorsports or your
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. REAR VIEW CAMERA ATTACHMENT PILOT AII 23620 Issue Date MAY 2002 PARTS LIST Attachment Kit : P/N 08B21-S9V-100 Control unit harness Rear
More informationINSTALLATION INSTRUCTIONS Accessory ACCESSORY HANDSFREELINK Application 2010 CR-V Publications No. AII 42587 Issue Date AUG 2009 PARTS LIST HFL Attachment Kit P/N 08E02-SWA-130 (Ivory) P/N 08E02-SWA-170
More informationTOYOTA PRIUS V LED DRL Black-Out
TOYOTA PRIUS V 2012 - LED DRL Black-Out Part Number: 00016-47021 Accessory Code:LDBO10 Conflicts Fog Lights Kit Contents Item # Quantity Reqd. Description 1 2 DRL Housing 2 2 DRL s bezels 3 1 Driver Box
More informationAmp & Speaker Upgrade Install Instructions for Batwing Fairing
Amp & Speaker Upgrade Install Instructions for Batwing Fairing Tools Needed: 1/2 inch Socket Wire Cutters 7/16 inch Socket Wire Strippers 10 mm Socket Phillips Screwdriver 1/2 inch Ratchet Wrench T25 Torx
More informationwiring instructions NEW FORD WIRE MOD 60 INCH BLADE INCH BLADE
wiring instructions 2018-2019 + NEW FORD WIRE MOD New technologically advanced logic box solves and eliminates all codes from trailering, backup assist, BLIS (Blind Spot Information System) and all currently
More informationRaingear Mustang Windshield Wiper System Installation Instructions E F A
Raingear 1965-1966 Mustang Windshield Wiper System Installation Instructions J I H J G E F A D K 2 speed switch B C L Intermittent switch Please try our way first. This system is designed to fit in your
More information2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions
2017 Current Ford Raptor Stealth Fighter Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: KIT-CARBON FIBER REAR SPOILER INFINITI Q50 T99J1 J5000 KIT CONTENTS: Item A B C D Qty. 1 4 1 1 Part Description Spoiler Assembly
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S Application 2013 ACCORD 4-DOOR Publications No. AII 13026 Issue Date AUG 2012 PARTS LIST Aluminum tape Backup Sensors Attachment Kit P/N 08V67-T2A-100A Control unit
More informationLED Fog Light. Conflicts Note: 1226, General Applicability Fits Models Additional Items Required For Installation
LED Fog Light Year & Model Part Number Conflicts Note: 1226, 1228 2017 Prius TPR-817 General Applicability Fits Models 1221 1225 1223 1227 1224 Additional Items Required For Installation Items 1 N/A 2
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2012 RIDGELINE Publications No. AII 12006 Issue Date NOV 2011 PARTS LIST Back-up sensor harness 3 Wire ties with small clips (2 Not used)
More information(1) License Plate Light (2) License Plate Plugs
PARTS LIST: 1 HD Replacement Bumper 4 12mm x 40mm Hex Bolts 1 Driver/Left Bracket 4 12mm Nylon Lock Nuts 1 Passenger/Right Bracket 8 12mm x 37mm x 3mm Oversize Flat Washers 2 Thin Side Spacers 4 Rubber
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory HARNESS P/N 08L91-SJC-100C Application 2009 RIDGELINE Publications No. AII 40322 Issue Date AUG 2008 PARTS LIST 3 Riv nuts, 6 mm Trailer socket harness Subharness kit
More informationMustang 5.0L Cold Air Intake Installation Instructions P/N:
2015-2017 Mustang 5.0L Cold Air Intake Installation Instructions P/N: 421826 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH 2015-2017 Mustang 5.0L Cold Air Intake Installation Instructions P/N:
More informationToggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta
Toggle Button Kit Installation Instructions MK5 / MK6 Golf, MK5 Jetta Thank you for choosing the Double Apex Toggle Button kit. If you have any questions about the installation please do not hesitate to
More informationINSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 33026 S 2007 ODYSSEY Issue Date JULY 2006 PARTS LIST Short sub harness (LX model) Right fog light Long sub harness (EX model and Touring
More informationRemove the 3-11mm nuts holding mirror on. Don t drop the nuts!
2005-2012 Ford Mustang Puddle Lamp Kit Parts List: Quantity: Tool List: LED Lamps 2 Flat head screwdriver Seals 2 Ratchet & Socket set OR Nuts 2 Adjustable Wrench Wiring harness 1 Drill & 11/16 th bit
More informationPart Number: Code: YU1 Kit Contents Item # Quantity Reqd. Description 1 1 RH Lamp Assy. 2 1 LH Lamp Assy.
Document # 3263 5/16/05 SCION tc 2005 - TAIL LIGHT ENHANCEMENT Preparation Part Number: 00016-21550 Code: YU1 Kit Contents 1 1 RH Lamp Assy. 2 1 LH Lamp Assy. 3 1 Hardware Bag Hardware Bag Contents 1 1
More informationDASH AUDIO KIT P/N APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Instr Rev 01 04/16 Page 1 of 6. Verify accessory fitment at Polaris.com.
DASH AUDIO KIT P/N 2882030 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain these
More informationPassenger/Right Upper U- Bracket OE fog light only. Driver/Left Upper U- Bracket OE fog light only. Winch Tray
PARTS LIST: 1 HD Bull Nose Bumper 48 12mm x 32mm x 3mm Flat Washers 1 Driver/left Frame Bracket 28 12mm Lock Washers 1 Passenger/right Frame Bracket 28 12-1.75mm Hex Nuts 1 Winch Tray 1 Access Cover 2
More informationSCION xb AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/ PRNDL 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description 1 2 T-tap Connectors,
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory S P/N 08V67-SJC-101 Application 2010 RIDGELINE Publications No. AII 42117 Issue Date AUG 2009 PARTS LIST Back-up sensor harness 3 Wire ties with small clip (2 Not used)
More informationSCION xa AUTO-DIMMING MIRROR Preparation
Preparation Part Number: PT374-52040 (Compass) PT374-21050 (Homelink) Kit Contents Item # Quantity Reqd. Description 1a 1 AD Mirror Assembly w/compass & Map Lights (P/N PT374-52040) 1b 1 AD Mirror Assembly
More informationSTEERING COLUMN SWITCHES
STEERING COLUMN SWITCHES 1994 Toyota Celica 1994 ACCESSORIES & EQUIPMENT Toyota Motor Sales, U.S.A., Inc. - Steering Column Switches Celica * PLEASE READ THIS FIRST * WARNING: Are equipped with a driver-side
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. All 28593 2006 RIDGELINE P/N 08F23-SJC-100 Issue Date FEB 2005 PARTS LIST Center front bumper trim (Not used if the vehicle is equipped
More informationInstallation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo
Installation instruction do88 Intercooler for SAAB 9-3SS/SC 4-cyl Turbo This instruction shows how to replace the OEM intercooler with this performance intercooler. 1. 4. 5. At this type of installation
More informationTOYOTA RAV FOG LIGHT KIT Preparation
Preparation Part Number: PT413-42163 Kit Contents Item # Quantity Reqd. Description 1 7 7 Wire Tie 2 4 #10-16 Cross Pan-Washer Head Screws 3 1 Switch 4 1 Relay 5 1 LH Fog Light Bezel 6 1 RH Fog Light Bezel
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory P/N 08U97-TX4-200 Application 2016 RDX Publications No. VERSION 1 Issue Date APRIL 2015 PARTS LIST Steering wheel Illustration of the Steering Wheel in the Vehicle 2
More informationMulti-Function Switch
1 of 9 Nissan Frontier, Xterra 1998-05 Multi-Function Switch REMOVAL & INSTALLATION Fig. Multi-function switch component locations 1998-2000-2000 shown Before servicing, or working around, the SRS system,
More information