GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS FOG LIGHT KIT

Size: px

Start display at page:

Download "GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS FOG LIGHT KIT"

Alyson Caldwell
5 years ago
Views:

PART NUMBER: 0000-8F-H99 ( 09-10) 0000-8F-H89 ( 11 - ) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS FOG LIGHT KIT APPLICABLE MODELS: 2009> MAZDA6 NOTE: Supplemental combination switch is required

PACKAGE CONTENTS: Cover RH Service # Cover LH Service # GS3M-50-C10E ( 09-10) GS3M-50-C20E ( 09-10) GEG1-51-C10 ( 11 - ) GEG1-51-C20 ( 11 - ) Jumper Harness Service # GS3L-51-688 ( 09-10) GEG1-51-688

1 PART NUMBER: F-H99 ( 09-10) F-H89 ( 11 - ) GENUINE ACCESSORIES INSTALLATION INSTRUCTIONS FOG LIGHT KIT APPLICABLE MODELS: 2009> MAZDA6 NOTE: Supplemental combination switch is required for installation on North American vehicles, part number listed below. PACKAGE CONTENTS: Cover RH Service # Cover LH Service # GS3M-50-C10E ( 09-10) GS3M-50-C20E ( 09-10) GEG1-51-C10 ( 11 - ) GEG1-51-C20 ( 11 - ) Jumper Harness Service # GS3L ( 09-10) GEG ( 11 - ) Bracket RH Service # GS3M ( 09-10) GEG ( 11 - ) Bracket LH Service # GS3M ( 09-10) GEG ( 11 - ) Bracket Set Screw (Qty 2) Self Tapping Screw (Qty 8) Service # ( 09-10) Service # ( 11 - ) Fog Lamp RH Service # GS3L ( 09-10) GEG ( 11 - ) Fog Lamp LH Service # GS3L ( 09-10) GEG ( 11 - ) Combination Screw (Qty 2) Supplemental Part Required For Installing Fog Light Kit in North American Vehicles: Combination Switch Part # GS3M A Tools Required: - Philips Screw Driver - 8mm Socket - 10 mm Socket - Fiber Stick or Non Marking Plastic Tool - Torque Wrench Page1of11 Part No: INST-8F-H99A Revised: Aug 30, 2010

2 Page2of11

-2.- -4.- -5.- -3.- Remove 3 screws from the steering column. Remove the 2 screws securing the combination switch to the steering column.

3 Remove 3 screws from the steering column. Remove the 2 screws securing the combination switch to the steering column. Using a fiber stick, release the harness from the back of the combination switch. Note this harness is simply attached to the back of the switch, it is not part of the combination switch assembly. Disconnect and remove the combination switch Obtain the new combination switch, GS3M A not included in the installation kit. Reconnect the combination switch. Page3of11

Install combination switch screws G22E-51-695.

seated. Reinstall the 3 removed steering column cover screws. -11.- -10.- -8.- -9.

Remove the 12 screws shown. -13.- -12.- Save for re assembly!

4 Install combination switch screws G22E Note, the combination switch will slide completely in and nest to the steering column when properly seated. Reinstall the 3 removed steering column cover screws Inspect cover to ensure there is no gap around column or key cylinder shown in box -8-. Remove the 12 screws shown Save for re assembly! Save for re assembly! Remove the 3 screws holding the OEM bezel in place, and disconnect the prewire from the bezel on the drivers side. Remove the 3 screws holding the bezel in place on the passanger side. Page4of11

5 -14.- Locate the 6 retaining tabs on the OEM bezel and front fascia. Using a fiber stick, release the 6 tabs from the OEM bezel. Carefully push the OEM bezel in side to free from the fascia. Slide the OEM bezel out. Repeat the procedure on the drivers side Remove the lower horn from the bracket, 10 mm (passenger side only for room for re installation) Connect jumper harness GS3L (from installation kit) into open connector by the bottom of the windshield washer fluid tank. (Passenger side only) Page5of11

- Inspect both assemblies ensuring bezels are completely seated to the front fascia on both the drivers and passenger side.

6 -26.- Attach Jumper harness (from installation kit) to the fog light assembly (Passenger side only) Attach the previously removed 3 screws, and connect the OEM harness to the fog light assembly, drivers side. Torque to.3 ~ 1.5 N.m Inspect both assemblies ensuring bezels are completely seated to the front fascia on both the drivers and passenger side. Re-install horn to horn bracket. Torque to x pounds Re-install splash shield, outer then middle. Re-install 12 screws retaining splash guard Page6of11

Note the bracket screw will seat in the cut out, preventing the need for lamp adjustment. Torque to 4.41 ~ 5.39 N.m -23.

7 On a protected surface, assemble the RH bracket, with RH lamp, by carefully inserting the side post of the lamp into the bracket, and installing bracket screw from the installation kit. Note the bracket screw will seat in the cut out, preventing the need for lamp adjustment. Torque to 4.41 ~ 5.39 N.m Install 4 of the 8 self tapping screws from the installation to secure the lamp bracket assembly to the fog light bezel from the installation kit. Repeat steps for the LH side. Torque to.3 ~ 1.5 N.m Carefully slide assembly into front fascia and align for re-assembly. Re align the 6 retaining tabs from the front fascia to the Fog light bezel. Note: Use care to prevent scratching vehicle or bezel! Push the bezel and fascia together so the bezel nest flush to the bumper. Repeat these steps on the drivers side. Install the three previously removed screws in the fog light assembly to the fascia. Torque to.3 ~ 1.5 N.m Page7of11

8 -32.- Basic operation and function check. Page8of11

9 -33.- Verify aiming, and adjust if needed using below procedure Bulb replacement procedure (for reference). Access fog lamp assembly using step 11, it will not necessary to remove the assembly to change the bulb. Page9of11

-31.- -32.- 1. Complete the inspection sheet and retain the sheet for evidence of quality of installation 2.

10 Complete the inspection sheet and retain the sheet for evidence of quality of installation 2. Make sure to reset automatic windows and radio stations. 3. Offer removed parts to customer. 4. Review the operations with customer Page10of11

11 Record preset radio and satellite stations. Am ( up to 6 channels) FM ( up to 12 channels) Sat ( up to 18 channels) Page11 of11

GENUINE PARTS INSTALLATION INSTRUCTIONS

GENUINE PARTS INSTALLATION INSTRUCTIONS 1. DESCRIPTION: 2. APPLICATION: 3. PART NUMBER(S) REQUIRED FOR INSTALLATION: 4. KIT CONTENTS: Item Qty. Fog Lamp Kit Titan MY16 999F1 W4000 Fog Lamp Kit Part Description