Item C& D Not Applicable C

Transcription

1 GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER(S) REQUIRED FOR INSTALLATION: KIT CONTENTS: LED Fog Lamp Upgrade Rogue Sport 999F1 V4001 A B Item C& D Not Applicable C D Do not use for Rogue Sport E _T99F1_6MALDII Page 1 of 14

2 PART NUMBER(S) REQUIRED FOR INSTALLATION: A B C D E F 999F1 V4001 KIT CONTENTS: Item Qty. Part Description Service Part Number 1 RH LED Fog Lamp Assembly 1 LH LED Fog Lamp Assembly 2 Fog Lamp Sub Harness 4 Cable Ties 1 II Replacement Template N/A Installation Instructions Not Applicable - Do not use for Rogue Sport Not Serviceable- Part of Kit 999F1 V4001 TOOLS REQUIRED: Ratchet, 1/4" drive Torque Wrench, 1/4" drive Nylon Trim Stick Socket, 10mm, 1/4" drive Screwdriver, T-20, Torx Tape, Masking or equivalent Extension, 100mm, 1/4" drive Screwdriver, Phillips #2 INSTALLATION CAUTIONS: CAUTION Dealer installation recommended. Sub Harness Kit (C) not used for Rogue Sport, DO NOT USE - DISPOSE. Please read this instruction carefully before installing this product for correct installation. Please DO NOT use or install the part in ways other than what is described herein. Always use floor, seat and steering wheel protection. If problem occurs during installation, please contact Nissan dealer where product was purchased. Always remove vehicle parts in the sequence directed, improper procedure can damage parts. Take care not to scratch or damage any component during the removal or re-installation process. Trim pieces found to have witness marks or broken clips ARE NOT to be reinstalled. Store removed parts in a safe and protected manner. Apply masking tape as needed to protect any areas that may become scratched or damaged _T99F1_6MALDII Page 2 of 14

3 SECTION 1 - OVERVIEW 1.1) SYSTEM 1.2) VEHICLE _T99F1_6MALDII Page 3 of 14

4 SECTION 2 - OVERVIEW CAUTION Always confirm the ignition is in the "OFF" position before changing the E.S.S. position. If E.S.S. is not in Customer Mode, there will be a loss of normal vehicle operation, preventing accessory function check. A 2.1) Check Extended Storage Switch Position a) Put shift lever in "P" position for A/T and CVT or "1st" for M/T. b) c ) d) e) f ) Apply park brake. Place ignition in "OFF" mode. Locate Extended Storage Switch in cabin fuse block as Confirm Extended Storage Switch is in "Customer" (In/Engaged) position. If ESS is not In/Engaged, then proceed to step ) Changing ESS Position a) To disengage Customer Mode, pull out in A direction as b) To engage Customer Mode, press in B direction as B C Condition Switch Position Note Vehicle is delivered to the dealer Transit (OUT) Vehicle is being stored at the dealer Transit (OUT) Vehicle is delivered to customer Customer (IN) 2.3) Record Customer Presets Place ignition in "ON" mode. a) b) Record the customer radio presets and other presets as required. Preset c ) Place ignition in "OFF" mode _T99F1_6MALDII Page 4 of 14

5 SECTION 2 - VEHICLE PREPARTION 2.4) Removing airbox assembly. a) Locate lift points, set hoist arms and raise vehicle to necessary work height. WARNING Always use proper lift points as specified in Service Manual Section: GI Be sure vehicle is secure on locks before proceeding underneath. 2.5) Removing airbox assembly. a) b) Open vehicle hood. Locate three (3) retainers for air box. Clip 1 Clip 2 Ball Mount Stud Front of Vehicle 2.6) Removing airbox assembly. a) Gently pull Clip 2 outward to release tab as 2.7) Removing airbox assembly. Lift ball stud out of socket as a) b) Remove airbox assembly, place in safe area until re-installation _T99F1_6MALDII Page 5 of 14

6 SECTION 2 - VEHICLE PREPARTION 2.8) Battery terminal removal. a) Locate negative battery terminal. b) Loosen nut with 10mm socket. Battery Terminal Nut CAUTION Allow 3 min after key off with doors closed for vehicle power to time out. 2.9) Battery terminal removal. a) Lift negative battery terminal off nut. b ) Isolate negative battery terminal. CAUTION Allow 3 min after negative terminal disconnect before separating any electrical connectors. 2.10) Moving front under cover. a) b ) c ) Remove six (6) Large Trim Clip from covers front edge as Remove nine (9) trim clips as Carefully let engine under cover hang down. Large Trim Clip Small Trim Clip _T99F1_6MALDII Page 6 of 14

7 SECTION 3 - TRIM REMOVAL, EXTERIOR 3.1) Moving RH fender protector. a ) Locate front part of RH fender protector as b ) Remove five (5) T20 Torx screws. c ) Remove one (1) Small trim clip. T20 Torx screws Small Trim Clip 3.2) Moving RH fender protector. a) Remove splash shield from RH fender protector. 3.3) Moving RH fender protector. a) Remove one (1) T20 Torx screw. T20 Torx screws 3.4) Moving RH fender protector. a) Move RH fender protector down and back as Front of Vehicle _T99F1_6MALDII Page 7 of 14

8 SECTION 3 - TRIM REMOVAL, EXTERIOR 3.5) Moving LH fender protector. Locate front part of LH fender protector as a) b) c ) Remove five (5) T20 Torx screws. Remove one (1) Small trim clip. T20 Torx screws Small Trim Clip 3.6) Moving LH fender protector. a) Remove splash shield from LH fender protector. 3.7) Moving LH fender protector. a) Remove one (1) T20 Torx screw. T20 Torx screws 3.8) Moving LH fender protector. a ) Move LH fender protector down and back as Front of Vehicle _T99F1_6MALDII Page 8 of 14

9 SECTION 3 - TRIM REMOVAL, EXTERIOR 3.9) LH halogen fog lamp removal. a) Remove pre wire connector from fog lamp assembly as 3.10) LH halogen fog lamp removal. a ) Remove two (2) 10mm screw into location as 10mm Screw 3.11) LH halogen fog lamp removal. a ) Remove halogen fog lamp assembly as _T99F1_6MALDII Page 9 of 14

10 SECTION 4 - INSTALLATION PROCEDURE, EXTERIOR 4.1) LH LED fog lamp installation. a) Install LED fog lamp assembly into location as 4.2) Installing LH fog lamp bracket a) Install two (2) 10mm screw into location as b) Torque two (2) 10mm bolts to 5.4 N-m. 10mm SCREW 4.3) Installing LH fog lamp bracket a) Install one (1) 10mm screw into location 10mm SCREW 4.4) Installing LH splash shield. a) Install LH splash shield from LH fender protector. Front of Vehicle _T99F1_6MALDII Page 10 of 14

11 SECTION 4 - INSTALLATION PROCEDURE, EXTERIOR 4.5) Installing LH fender protector fasteners. a) Install five (5) T20 Torx screws. b) Install one (1) Small trim clip. T20 Torx screws Small Trim Clip 4.6) Installing LH fender protector fasteners. a) Install one (1) T20 Torx screws. T20 Torx screws 4.7) Installing the RH fog lamp assy a) Repeat steps for RH side of vehicle. 4.16) Installing front under cover. a) Carefully manuever engine under cover up and back into position. b) Install six (6) Large Trim Clip as c ) Install nine (9) Small Trim Clips Large Trim Clip Small Trim Clip _T99F1_6MALDII Page 11 of 14

12 SECTION 5 - FINAL CAUTION Take care not to scratch or damage any component during the removal or re-installation process. Trim pieces found to have witness marks or broken clips should be replaced with new parts. 5.1) Accessory function check. a) Perform checklist as follows. Connect the battery negative terminal and tighten the nut to 5.4 N-m. Re-install underhood air box assembly Verify re-installed trim parts for proper flush fit (no gaps, no waviness, etc.). Verify all clips are fully engaged and locked. Verify re-installed trim parts for proper fit (no gap, waviness, etc.). Verify all windows and sunroof (if equipped), one touch operation and perform the reset procedure if necessary. Refer to the vehicle Service Manual for more details. Re-program radio presets and other vehicle settings to the recorded settings if necessary. Remove all tools, templates, and other debris from interior of vehicle. Verify vehicle headliner, seat, steering wheel, center console, carpet, etc. are not soiled. Verify interior and exterior are not damaged _T99F1_6MALDII Page 12 of 14

13 SECTION 5 - FINAL CAUTION Refer to the vehicle service manual for more information on the procedures outlined below Make sure all connectors are engaged and locked before proceeding with accessory check. Make sure no system malfunction is detected by air bag warning lamp. If malfunction is detected, reset by self-diagnosis function and delete code using CONSULT III+. Follow Front fog lamp aiming adjustment procedure as directed in Service Manual, Sect L - Exterior Lighting System EXL-122 Inspection and Adjustment. 5.2) Accessory function check. a) Perform checklist as follows. Turn ignition switch to "ON" and confirm proper operation of the following vehicle systems and verify: Confirm proper audio function (AM, FM, SAT, CD and AUX) and re-program radio presets. That there are no new Diagnostic Trouble Codes. Verify all windows and sunroof (if equipped), one touch operation and perform the reset procedure if necessary. Refer to the vehicle service manual for more details. Power Back Door (If equipped). - Turn on the car, push and note if trunk opens. Tail Lamp - Turn on headlamps; open glove box and note whether light goes on. Start vehicle. Note whether vehicle starts. Turn headlamp and fog lamp switches to the ON position. Verify headlamps, fog lamps and tail lamps are illuminated. Verify headlamps and fog lamp indicators are illuminated on the meter assembly. Verify turn signal, hazard and high beam functionality. Verify turn signal, hazard and high beam indicators are illuminated on the meter assembly. Verify turn wiper and washer functionality. Turn headlamp switch to the OFF position, leaving the fog lamp switch in the ON position. Verify both headlamp and fog lamps turn off. Re-program radio presets and other vehicle settings to the recorded settings. Front Sonar Module Connector (if equipped) - Turn on vehicle, put vehicle in 'Drive'. Move slowly towards a large object in front of the vehicle. Note whether alarm sounds. Rear Sonar Module Connector (if equipped) - Turn on vehicle, put vehicle in 'Reverse'. Move slowly towards a large object behind the vehicle. Note whether alarm sounds _T99F1_6MALDII Page 13 of 14

14 APPENDIX A - MECHANIZATION: Fog Lamp Function : System Description _T99F1_6MALDII Page 14 of 14